[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 04 05 06 07 08 RFC 6766

Network Working Group                                           E. Beili
Internet-Draft                                          Actelis Networks
Intended status: Standards Track                          March 12, 2012
Expires: September 13, 2012


    xDSL multi-pair bonding using Time-Division Inverse Multiplexing
                           (G.Bond/TDIM) MIB
                draft-ietf-adslmib-gbond-tdim-mib-08.txt

Abstract

   This document defines Management Information Base (MIB) module for
   use with network management protocols in TCP/IP based internets.
   This document proposes an extension to the GBOND-MIB module with a
   set of objects for managing multi-pair bonded xDSL interfaces using
   Time-Division Inverse Multiplexing (TDIM), defined in ITU-T
   recommendation G.998.3.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on September 13, 2012.

Copyright Notice

   Copyright (c) 2012 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of



Beili                  Expires September 13, 2012               [Page 1]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
   2.  The Internet-Standard Management Framework . . . . . . . . . .  3
   3.  The Broadband Forum Management Framework for xDSL Bonding  . .  3
   4.  Relationship to other MIB modules  . . . . . . . . . . . . . .  3
     4.1.  Relationship to Interfaces Group MIB module  . . . . . . .  4
     4.2.  Relationship to G.Bond MIB module  . . . . . . . . . . . .  4
   5.  MIB Structure  . . . . . . . . . . . . . . . . . . . . . . . .  4
     5.1.  Overview . . . . . . . . . . . . . . . . . . . . . . . . .  4
     5.2.  Link Protection Configuration  . . . . . . . . . . . . . .  5
     5.3.  Service Configuration  . . . . . . . . . . . . . . . . . .  5
       5.3.1.  Management of TDM Services and service drop
               priority during bandwidth degradation  . . . . . . . .  6
       5.3.2.  Service Notifications  . . . . . . . . . . . . . . . .  6
     5.4.  Performance Monitoring . . . . . . . . . . . . . . . . . .  7
     5.5.  Mapping of Broadband Forum TR-159 and ITU-T G.998.3
           Managed Objects  . . . . . . . . . . . . . . . . . . . . .  7
   6.  G.Bond/TDIM MIB Definitions  . . . . . . . . . . . . . . . . .  9
   7.  Security Considerations  . . . . . . . . . . . . . . . . . . . 50
   8.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 51
   9.  Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . . 51
   10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 52
     10.1. Normative References . . . . . . . . . . . . . . . . . . . 52
     10.2. Informative References . . . . . . . . . . . . . . . . . . 53























Beili                  Expires September 13, 2012               [Page 2]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


1.  Introduction

   The Multi-pair bonding using time-division inverse multiplexing
   (TDIM), a.k.a.  G.Bond/TDIM, is specified in ITU-T G.998.3
   recommendation [G.998.3], which defines a method for bonding (or
   aggregating) of multiple xDSL lines (or individual bearer channels in
   multiple xDSL lines) into a single bi-directional logical link,
   carrying a mix of various traffic streams, e.g.  Ethernet,
   Asynchronous Transfer Mode (ATM), Time-Division Multiplexing (TDM).

   The MIB module, defined in this document, provides G.Bond/
   TDIM-specific objects for the management of G.998.3 bonded
   interfaces, extending the common bonding objects specified in GBOND-
   MIB [I-D.ietf-adslmib-gbond-mib] module.

2.  The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI).  This memo specifies a MIB
   module that is compliant to the SMIv2, which is described in STD 58,
   RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
   [RFC2580].

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in RFC
   2119 [RFC2119].

3.  The Broadband Forum Management Framework for xDSL Bonding

   This document makes use of the Broadband Forum technical report
   Management Framework for xDSL Bonding [TR-159], defining a management
   model and a hierarchy of management objects for the bonded xDSL
   interfaces.

4.  Relationship to other MIB modules

   This section outlines the relationship of the MIB modules defined in
   this document with other MIB modules described in the relevant RFCs.
   Specifically, the following MIB modules are discussed: Interfaces
   Group MIB (IF-MIB) and G.Bond MIB (GBOND-MIB).



Beili                  Expires September 13, 2012               [Page 3]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


4.1.  Relationship to Interfaces Group MIB module

   A G.Bond/TDIM port is a private case of a Bonded multi-pair xDSL
   interface and as such is managed using generic interface management
   objects defined in the IF-MIB [RFC2863].  In particular an interface
   index (ifIndex) is used to index instances of G.Bond/TDIM ports, as
   well as xDSL lines/channels, in a managed system.

4.2.  Relationship to G.Bond MIB module

   GBOND-MIB [I-D.ietf-adslmib-gbond-mib] module defines management
   objects common for all Bonded multi-pair xDSL interfaces.  In
   particular it describes the bonding management, bonded port and
   channel configuration, initialization sequence etc.

   Both GBOND-MIB and G9983-MIB modules are REQUIRED to manage a G.Bond/
   TDIM port.

5.  MIB Structure

5.1.  Overview

   All management objects defined in the G9983-MIB module are contained
   in a single group g9983Port.  This group is further split into 6 sub-
   groups, structured as recommended by RFC 4181 [RFC4181]:

   o  g9983PortNotifications - containing notifications (TDIM Service
      Down/Up).

   o  g9983PortConfTable - containing objects for configuration of a
      G.Bond/TDIM port.

   o  g9983PortCapTable - containing objects reflecting capability of a
      G.Bond/TDIM port.

   o  g9983PortStatTable - containing objects providing overall status
      information of a G.Bond/TDIM port, complementing the generic
      status information from the ifTable of IF-MIB and
      gBondPortStatFltStatus of GBOND-MIB.

   o  g9983SvcTable - containing objects for configuration and status of
      the services in a G.Bond/TDIM port.

   o  g9983PM - containing objects for an OPTIONAL Historical
      Performance Monitoring (PM) of a G.Bond/TDIM port.






Beili                  Expires September 13, 2012               [Page 4]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


5.2.  Link Protection Configuration

   G.Bond/TDIM specification allows an optional Forward Error Correction
   (FEC) and Interleaver block, which, if supported and enabled,
   provides a degree of protection against micro-interruptions, alien
   noise, and even individual Bonding Channel Entity (BCE) failures,
   a.k.a. cut-line protection.

   Management objects in the g9983PortConfTable can be used to configure
   and query the FEC and Interleaver function of the G.Bond/TDIM port.

5.3.  Service Configuration

   Unlike the other two xDSL Multi-Pair Bonding schemes (G.Bond/ATM and
   G.Bond/Ethernet), which send the information required for reassembly
   of the fragmented data along with the data, G.Bond/TDIM is a
   synchronous scheme, requiring both ends to know the data distribution
   tables before any actual data transfer can happen.

   Management objects in the g9983PortConfTable
   (g9983PortConfAdminServices), g9983SvcTable and g9983OperSvcTable can
   be used to configure and query the configuration of services
   transported via the G.Bond/TDIM link.  The services may be configured
   independently of the link state (i.e. in- and out-of-service), as
   G.998.3 communicates changes in the service configuration via
   specific Bonding Communication Channel (BCC) messages, switching both
   ends of the link to the new configuration synchronously.

   There can be up to 60 active services defined on a G.Bond/TDIM link.
   This MIB module provides an ability to define up to 255 services via
   the g9983SvcTable, with each row representing a possible service, and
   then set the actual service configuration using the
   g9983PortConfAdminServices object (a byte-vector of service indices),
   listing the active services in the order of their position in the
   G.Bond/TDIM frame.  This design allows one to easily modify service
   drop priority, which directly corresponds to the service position.

   The actual list of services is provided via the read-only
   g9983OperSvcTable, where each entry's index corresponds to the
   service position, starting from index 1 for the first entry, 2 for
   the second entry etc., providing an easy service navigation for a
   management application using GET-NEXT (instead of counting bytes in
   the g9983PortConfAdminServices object).

   The service configuration can only be changed on a Bonding
   Transmission Unit at the Central Office (BTU-C).

   When configuring the services, please bear in mind that the sum of



Beili                  Expires September 13, 2012               [Page 5]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


   all the services' bandwidth SHOULD be less or equal to the target
   data rate of the bonded link.  Note that G.Bond/TDIM links are
   symmetrical, i.e. their upstream data rate equals to the downstream
   data rate.

5.3.1.  Management of TDM Services and service drop priority during
        bandwidth degradation

   G.Bond/TDIM protocol provides an ability to map TDM services into the
   TDIM bonded link directly, without any additional overhead.  It
   addresses only structure-agnostic TDM transport, disregarding any
   structure that may be imposed on these streams, in particular the
   structure imposed by the standard TDM framing [G.704].

   During bandwidth degradation services with a lower priority are
   impaired or dropped first.  Synchronous services (fractional DS1/E1,
   clear channel E1/T1, T3/E3, clock) positioned in the beginning of the
   G.Bond/TDIM frame, have higher priority than asynchronous services
   (Ethernet, ATM, GFP encapsulated), positioned farther away.  Within
   the services of the same type, those with lower position (index) have
   higher priority.

5.3.2.  Service Notifications

   This MIB module provides specific Up/Down notifications (g9983SvcUp/
   g9983SvcDown) for each of the configured services.  During bandwidth
   degradation a number of services may be suspended (dropped)
   simultaneously, according to their drop priority (position in the
   service list).  Please note that it is possible for a higher priority
   service to be dropped before a lower priority one.  For example,
   suppose there are two services configured on a 2 Mbps G.Bond/TDIM
   link: a T1 service (g9983SvcType with a value of ds1, with a
   bandwidth requirement of 1.5 Mbps) and an Ethernet service with a
   size of 0.5 Mbps.  When the actual link bandwidth is reduced to 1.4
   Mbps, the T1 service with a g9983OperSvcPosition value of 1 would be
   dropped, while the Ethernet service with a g9983PerSvcPosition value
   of 2 would remain up.

   Notifications SHOULD be rate-limited (throttled) such that there is
   an implementation-specific gap between the generation of consecutive
   notifications of the same event.  This mechanism prevents
   notification flooding in case g9983ServiceOperState oscillates
   between Up and Down states.  When notifications are rate-limited,
   they are dropped and not queued for sending at a future time.  This
   is intended to be a general rate-limiting statement for notifications
   that otherwise have no explicit rate-limiting assertions in this
   document.




Beili                  Expires September 13, 2012               [Page 6]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


5.4.  Performance Monitoring

   The OPTIONAL performance monitoring counters, thresholds and history
   buckets (interval-counters), similar to those defined in [TR-159] are
   implemented using the textual conventions defined in the HC-PerfHist-
   TC-MIB [RFC3705].  The HC-PerfHist-TC-MIB defines 64-bit versions of
   the textual conventions found in PerfHist-TC-MIB [RFC3593].

   The agent SHOULD align the beginning of each interval to a fifteen
   minute boundary of a wall clock.  Likewise, the beginning of each one
   day intervals SHOULD be aligned with the start of a day.

   Counters are not reset when a G.Bond TDIM port is reinitialized, but
   rather only when the agent is reset or reinitialized.

   Note that the accumulation of certain performance events for a
   monitored entity is inhibited (counting stops) during periods of
   service unavailability on that entity.  The DESCRIPTION clause of
   performance monitoring counters in this MIB module specifies which of
   the counters are inhibited during periods of service unavailability.

5.5.  Mapping of Broadband Forum TR-159 and ITU-T G.998.3 Managed
      Objects

   This section contains the mapping between relevant managed objects
   (attributes) defined in [TR-159] and managed objects defined in this
   document.  Note that all management objects defined in [G.998.3] have
   corresponding objects in [TR-159].























Beili                  Expires September 13, 2012               [Page 7]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


   +----------------------------+--------------------------------------+
   | TR-159 Managed Object      | Corresponding SNMP Object            |
   +----------------------------+--------------------------------------+
   | oBondTDIM - Basic Package  |                                      |
   | (Mandatory)                |                                      |
   +----------------------------+--------------------------------------+
   | aCRC4Errors                | g9983PortStatCrc4Errors              |
   +----------------------------+--------------------------------------+
   | aCRC6Errors                | g9983PortStatCrc6Errors              |
   +----------------------------+--------------------------------------+
   | aCRC8Errors                | g9983PortStatCrc8Errors              |
   +----------------------------+--------------------------------------+
   | aFECSupported              | g9983PortCapFecSupported             |
   +----------------------------+--------------------------------------+
   | oBondTDIM - FEC Package    |                                      |
   | (Optional)                 |                                      |
   +----------------------------+--------------------------------------+
   | aFECAdminState             | g9983PortConfFecAdminState           |
   +----------------------------+--------------------------------------+
   | aFECOperState              | g9983PortStatFecOperState            |
   +----------------------------+--------------------------------------+
   | aFECWordSize               | g9983PortConfFecWordSize             |
   +----------------------------+--------------------------------------+
   | aFECRedundancySize         | g9983PortConfFecRedundancySize       |
   +----------------------------+--------------------------------------+
   | aFECInterleaverType        | g9983PortConfFecInterleaverType      |
   +----------------------------+--------------------------------------+
   | aFECInterleaverDepth       | g9983PortConfFecInterleaverDepth     |
   +----------------------------+--------------------------------------+
   | aFECMaxWordSize            | g9983PortCapFecMaxWordSize           |
   +----------------------------+--------------------------------------+
   | aFECMaxRedundancySize      | g9983PortCapFecMaxRedundancySize     |
   +----------------------------+--------------------------------------+
   | aFECInterleaverTypesSuppor | g9983PortCapFecInterleaverTypeSuppor |
   | ted                        | ted                                  |
   +----------------------------+--------------------------------------+
   | aFECMaxInterleaverDepth    | g9983PortCapFecMaxInterleaverDepth   |
   +----------------------------+--------------------------------------+
   | oTDIMService - Basic       |                                      |
   | Package (Mandatory)        |                                      |
   +----------------------------+--------------------------------------+
   | aServiceID                 | g9983OperSvcPosition                 |
   +----------------------------+--------------------------------------+
   | aServiceIfIdx              | g9983SvcIfIdx                        |
   +----------------------------+--------------------------------------+
   | aServiceType               | g9983SvcType                         |
   +----------------------------+--------------------------------------+
   | aServiceSize               | g9983SvcSize                         |



Beili                  Expires September 13, 2012               [Page 8]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


   | aServiceOperState          | g9983OperSvcState                    |
   +----------------------------+--------------------------------------+
   | aServiceUpDownEnable       | g9983PortConfSvcUpDownEnable         |
   +----------------------------+--------------------------------------+
   | nServiceUp                 | g9983SvcUp                           |
   +----------------------------+--------------------------------------+
   | nServiceDown               | g9983SvcDown                         |
   +----------------------------+--------------------------------------+

                Table 1: Mapping of TR-159 Managed Objects

   Note that some of the mapping between the objects defined in TR-159
   and the ones defined in this MIB module is not one-to-one, for
   example, while TR-159 PM attributes aGroupPerf* map to the
   corresponding gBondPortPm* objects of the GBOND-MIB module, there are
   no dedicated PM attributes for the g9983PortPm* and g9983SvcPm*
   objects introduced in this MIB module.  However, since their
   definition is identical to the definition of gBondPortPm* objects of
   the GBOND-MIB module, we can map g9983PortPm* and g9983SvcPm* to the
   relevant aGroupPerf* attributes of TR-159 and use the term 'partial
   mapping' to denote the fact that this mapping is not one-to-one.

6.  G.Bond/TDIM MIB Definitions

G9983-MIB DEFINITIONS ::= BEGIN

  IMPORTS
    MODULE-IDENTITY,
    OBJECT-TYPE,
    NOTIFICATION-TYPE,
    mib-2,
    Unsigned32,
    Counter32
      FROM SNMPv2-SMI         -- [RFC2578]
    TEXTUAL-CONVENTION,
    RowStatus,
    TruthValue
      FROM SNMPv2-TC          -- [RFC2579]
    MODULE-COMPLIANCE,
    OBJECT-GROUP,
    NOTIFICATION-GROUP
      FROM SNMPv2-CONF        -- [RFC2580]
    ifIndex,
    InterfaceIndex
      FROM IF-MIB             -- [RFC2863]
    HCPerfCurrentCount,
    HCPerfIntervalCount,
    HCPerfValidIntervals,



Beili                  Expires September 13, 2012               [Page 9]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


    HCPerfInvalidIntervals,
    HCPerfTimeElapsed
      FROM  HC-PerfHist-TC-MIB  -- [RFC3705]
    ;
------------------------------------------------------------------------
  g9983MIB MODULE-IDENTITY
    LAST-UPDATED "201203120000Z"  -- Mar 12, 2012
    ORGANIZATION "IETF ADSL MIB Working Group"
    CONTACT-INFO
      "WG charter:
        http://www.ietf.org/html.charters/adslmib-charter.html

      Mailing Lists:
        General Discussion: adslmib@ietf.org
        To Subscribe: adslmib-request@ietf.org
        In Body: subscribe your_email_address

       Chair: Menachem Dodge
      Postal: ECI Telecom, Ltd.
              30 Hasivim St.,
              Petach-Tikva 4951169
              Israel
       Phone: +972-3-926-8421
       EMail: menachem.dodge@ecitele.com

      Editor: Edward Beili
      Postal: Actelis Networks, Inc.
              25 Bazel St., P.O.B. 10173
              Petach-Tikva 49103
              Israel
       Phone: +972-3-924-3491
       EMail: edward.beili@actelis.com"

    DESCRIPTION
      "The objects in this MIB module are used to manage the
      multi-pair bonded xDSL Interfaces using time-division inverse
      multiplexing (TDIM), defined in ITU-T recommendation G.998.3
      (G.Bond/TDIM).

      This MIB module MUST be used in conjunction with GBOND-MIB
      module, common to all G.Bond technologies.

      The following references are used throughout this MIB module:

      [G.998.3] refers to:
        ITU-T Recommendation G.998.3: 'Multi-pair bonding using
        time-division inverse multiplexing', January 2005.




Beili                  Expires September 13, 2012              [Page 10]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


      [TR-159] refers to:
        Broadband Forum Technical Report: 'Management Framework for
        xDSL Bonding', December 2008.

      Naming Conventions:
        BCE    - Bonding Channel Entity
        BTU    - Bonding Transmission Unit
        BTU-C  - Bonding Transmission Unit, CO side
        BTU-R  - Bonding Transmission Unit, Remote Terminal (CPE) side
        CO     - Central Office
        CPE    - Customer Premises Equipment
        GBS    - Generic Bonding Sublayer
        GBS-C  - Generic Bonded Sub-layer, CO side
        GBS-R  - Generic Bonded Sub-layer, Remote Terminal (CPE) side
        SNR    - Signal to Noise Ratio

      Copyright (C) The IETF Trust (2012).
      This version of this MIB module is part of RFC YYYY;
      see the RFC itself for full legal notices."

    REVISION    "201203120000Z"  -- Mar 12, 2012
    DESCRIPTION "Initial version, published as RFC YYYY."

      -- EdNote: Replace YYYY with the actual RFC number &
      -- remove this note

    ::= { mib-2 ZZZ }

      -- EdNote: Replace ZZZ with a real OID once it is
      -- allocated & remove this note.

   -- Sections of the module
   -- Structured as recommended by [RFC4181], Appendix D

   g9983Objects     OBJECT IDENTIFIER ::= { g9983MIB 1 }

   g9983Conformance OBJECT IDENTIFIER ::= { g9983MIB 2 }

   -- Groups in the module

   g9983Port        OBJECT IDENTIFIER ::= { g9983Objects 1 }

   -- Textual Conventions

   G9983SvcIndex ::= TEXTUAL-CONVENTION
     DISPLAY-HINT "d"
     STATUS       current
     DESCRIPTION



Beili                  Expires September 13, 2012              [Page 11]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       "A unique value, greater than zero, for each Service defined
       in the managed G.Bond/TDIM port.
       It is RECOMMENDED that values are assigned contiguously
       starting from 1. The value for each Service MUST remain
       constant at least from one re-initialization of the local
       management subsystem to the next re-initialization."
     SYNTAX       Unsigned32 (1..255)

   G9983SvcIndexList ::= TEXTUAL-CONVENTION
     DISPLAY-HINT "1d:"
     STATUS       current
     DESCRIPTION
       "This textual convention represents a continuous ordered list of
       all the services defined for the managed G.Bond/TDIM port.
       The value of this object is a concatenation of zero or more (up
       to 60) octets, where each octet contains an 8-bit
       G9983SvcIndex value, identifying a particular service.
       An octet's position reflects the associated service position
       and its priority in the G.Bond/TDIM frame, with 1st octet being
       the 1st service of highest priority.

       A zero-length octet string is object-specific and MUST
       therefore be defined as part of the description of any object
       that uses this syntax. Examples of the usage of a zero-length
       value might include situations where an object using this
       textual convention is irrelevant for a specific G.Bond/TDIM port
       type or that no services have been defined for this port."
     SYNTAX       OCTET STRING (SIZE(0..60))

   G9983SvcOrderIndex ::= TEXTUAL-CONVENTION
     DISPLAY-HINT "d"
     STATUS       current
     DESCRIPTION
       "A unique value, greater than zero, for each Service defined
       in the managed G.Bond/TDIM port, showing its relative position
       inside the G.Bond/TDIM frame."
     SYNTAX       Unsigned32 (1..60)

  -- Port Notifications Group

   g9983PortNotifications OBJECT IDENTIFIER
     ::= { g9983Port 0 }

   g9983SvcUp NOTIFICATION-TYPE
     OBJECTS {
       -- ifIndex and g9983OperSvcPosition would be part of the trap OID
       g9983OperSvcIdx,
       g9983SvcIfIdx



Beili                  Expires September 13, 2012              [Page 12]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     }
     STATUS      current
     DESCRIPTION
       "This notification indicates that a service, indicated by the
       g9983OperSvcIdx (mapped to a particular interface
       indicated by the g9983SvcIfIdx), in a particular
       G.Bond/TDIM port is passing traffic.

       This notification is generated (unless disabled or dropped by
       the rate limiting mechanism), when the g9983OperSvcState
       object has left the Down state, while the G.Bond/TDIM port
       state (ifOperStatus of IF-MIB) is Up.

       Generation of this notification is controlled by the
       g9983PortConfSvcUpDownEnable object.

       This object maps to the TR-159 notification nServiceUp."
     REFERENCE
       "[TR-159] 5.5.5.7"
     ::= { g9983PortNotifications 1 }

   g9983SvcDown NOTIFICATION-TYPE
     OBJECTS {
       -- ifIndex and g9983OperSvcPosition would be part of the trap OID
       g9983OperSvcIdx,
       g9983SvcIfIdx
     }
     STATUS      current
     DESCRIPTION
       "This notification indicates that a service indicated by the
       g9983OperSvcIdx (mapped to a particular interface
       indicated by the g9983SvcIfIdx) in a particular
       G.Bond/TDIM port has stopped passing the traffic.

       This notification is generated (unless disabled or dropped by
       the rate limiting mechanism), when the g9983OperSvcState
       object has entered the Down state, while the G.Bond/TDIM port
       state (ifOperStatus of IF-MIB) is Up.

       Generation of this notification is controlled by the
       g9983PortConfSvcUpDownEnable object.

       This object maps to the TR-159 notification nServiceDown."
     REFERENCE
       "[TR-159] 5.5.5.8"
     ::= { g9983PortNotifications 2 }

   -- G.Bond/TDIM Port group



Beili                  Expires September 13, 2012              [Page 13]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


   g9983PortConfTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9983PortConfEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Table for Configuration of G.Bond/TDIM ports. Entries in
       this table MUST be maintained in a persistent manner"
     ::= { g9983Port 1 }

   g9983PortConfEntry OBJECT-TYPE
     SYNTAX      G9983PortConfEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/TDIM Port Configuration table.
       Each entry represents an G.Bond/TDIM port indexed by the
       ifIndex. Additional configuration parameters are available
       via the gBondPortConfEntry of GBOND-MIB.
       Note that an G.Bond/TDIM port runs on top of a single or
       multiple BCE port(s), which are also indexed by ifIndex."
     INDEX  { ifIndex }
     ::= { g9983PortConfTable 1 }

   G9983PortConfEntry ::=
     SEQUENCE {
       g9983PortConfFecAdminState        TruthValue,
       g9983PortConfFecWordSize          Unsigned32,
       g9983PortConfFecRedundancySize    Unsigned32,
       g9983PortConfFecInterleaverType   INTEGER,
       g9983PortConfFecInterleaverDepth  Unsigned32,
       g9983PortConfAdminServices        G9983SvcIndexList,
       g9983PortConfSvcUpDownEnable      TruthValue
     }

   g9983PortConfFecAdminState  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "A desired state of the OPTIONAL Forward Error Correction
       (FEC) function of the G.Bond/TDIM port.

       A value of 'false' indicates that the FEC function SHALL be
       disabled. A value of 'true' indicates that the FEC SHALL be
       enabled, if supported by the G.Bond/TDIM port, as indicated
       by the g9983PortCapFecSupported object.
       The g9983PortStatFecOperState object indicates current
       operational state of the FEC function.



Beili                  Expires September 13, 2012              [Page 14]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       For the GBS-R ports, the value of this object cannot be changed
       directly. This value may be changed as a result of writing
       operation on the g9983PortCapFecSupported object of a remote
       GBS-C.

       Modifications of this object MUST be performed when the link
       is Down.
       Attempts to change this object MUST be rejected, if the link is
       Up or Initializing or if it is an GBS-R.

       This object maps to TR-159/G.998.3 attribute aFECAdminState."
     REFERENCE
       "[TR-159] 5.5.4.5; [G.998.3] Appendix II, B-X"
     ::= { g9983PortConfEntry 1 }

   g9983PortConfFecWordSize  OBJECT-TYPE
     SYNTAX      Unsigned32(0|20..255)
     UNITS       "octets"
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "A FEC code word size in octets for the G.Bond/TDIM ports
       supporting FEC function.

       This object is read-write for the GBS-C ports and read-only
       for the GBS-R.

       A value of zero SHALL be returned if the FEC is disabled
       (via g9983PortConfFecAdminState) or not supported.

       Changing of the FEC code word size MUST be performed when the
       FEC enabled link is Down. Attempts to change this object MUST
       be rejected, if the link is Up or Initializing or the
       FEC function is disabled/not supported.

       This object maps to TR-159/G.998.3 attribute aFECWordSize."
     REFERENCE
       "[TR-159] 5.5.4.7; [G.998.3] Appendix II, B-XI"
     ::= { g9983PortConfEntry 2 }

   g9983PortConfFecRedundancySize  OBJECT-TYPE
     SYNTAX      Unsigned32(0|2|4|8|16|20)
     UNITS       "octets"
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "A FEC redundancy word size in octets for the G.Bond/TDIM
       ports supporting FEC function.



Beili                  Expires September 13, 2012              [Page 15]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       This object is read-write for the GBS-C ports and read-only
       for the GBS-R.

       A value of zero SHALL be returned if the FEC is disabled
       (via g9983PortConfFecAdminState) or not supported.

       Changing of the FEC redundancy word size MUST be performed
       when the FEC enabled link is Down. Attempts to change this
       object MUST be rejected, if the link is Up or Initializing or
       the FEC function is disabled/not supported.

       This object maps to TR-159/G.998.3 attribute
       aFECRedundancySize."
     REFERENCE
       "[TR-159] 5.5.4.8; [G.998.3] Appendix II, B-XII"
     ::= { g9983PortConfEntry 3 }

   g9983PortConfFecInterleaverType  OBJECT-TYPE
     SYNTAX      INTEGER {
       none(0),
       block(1),
       convolution(2)
     }
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "An Interleaver type for the G.Bond/TDIM ports supporting
       FEC function.

       This object is read-write for the GBS-C ports and read-only
       for the GBS-R.

       A value of none(0) SHALL be returned if the FEC is disabled
       (via g9983PortConfFecAdminState) or not supported.

       Changing of the Interleaver type MUST be performed when the
       FEC enabled link is Down. Attempts to change this object MUST
       be rejected, if the link is Up or Initializing or the FEC
       function is disabled/not supported.

       This object maps to TR-159/G.998.3 attribute
       aFECInterleaverType."
     REFERENCE
       "[TR-159] 5.5.4.9; [G.998.3] Appendix II, B-XIII"
     ::= { g9983PortConfEntry 4 }

   g9983PortConfFecInterleaverDepth  OBJECT-TYPE
     SYNTAX      Unsigned32(0|1|2|3|4|6|8|12|16|24|32|48|96)



Beili                  Expires September 13, 2012              [Page 16]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "An Interleaver Depth for the G.Bond/TDIM ports supporting
       FEC function.

       This object is read-write for the GBS-C ports and read-only
       for the GBS-R.

       A value of zero SHALL be returned if the FEC is disabled
       (via g9983PortConfFecAdminState) or not supported.

       Changing of the Interleaver Depth MUST be performed when the
       FEC enabled link is Down. Attempts to change this object MUST
       be rejected, if the link is Up or Initializing or the FEC
       function is disabled/not supported.

       This object maps to TR-159/G.998.3 attribute
       aFECInterleaverDepth."
     REFERENCE
       "[TR-159] 5.5.4.10; [G.998.3] Appendix II, B-XIV"
     ::= { g9983PortConfEntry 5 }

   g9983PortConfAdminServices  OBJECT-TYPE
     SYNTAX      G9983SvcIndexList
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
      "Desired list of services for a G.Bond/TDIM port. This object is
       a list of pointers to entries in the g9983SvcTable.

       The value of this object is a continuous ordered list of up to
       60 indices (g9983SvcIdx) of the active services carried
       via the G.Bond/TDIM link. The position of a service in the
       list determines its relative priority in case of a bandwidth
       degradation - the priority decreases towards the end of the
       list, which means that the last service in the list would be
       suspended first when the bandwidth degrades.

       This object is writable and readable for the GBS-C ports.
       It is irrelevant for the GBS-R ports - a zero-length octet
       string SHALL be returned on an attempt to read this object and
       an attempt to change this object MUST be rejected in this case.

       Note that the current operational service list is available
       via the g9983OperSvcTable object.

       This object for a GBS-C port MAY be modified independently of



Beili                  Expires September 13, 2012              [Page 17]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       the link's state, i.e. in- and out-of-service.
       Attempts to set this object to a list with a member value that
       is not the value of the index for an active entry in the
       corresponding g9983SvcTable table MUST be rejected."
     REFERENCE
       "[G.998.3] 10.2.3, 13.3.4.6-13.3.4.11"
     ::= { g9983PortConfEntry 6 }

   g9983PortConfSvcUpDownEnable  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Indicates whether g9983SvcUp and g9983SvcDown
       notifications should be generated for this interface.

       Value of true(1) indicates that the notifications are enabled.
       Value of false(2) indicates that the notifications are
       disabled.

       This object maps to the TR-159 attribute
       aServiceUpDownEnable."
     REFERENCE
       "[TR-159] 5.5.5.6"
     ::= { g9983PortConfEntry 7 }


   g9983PortCapTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9983PortCapEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Table for Capabilities of G.Bond/TDIM ports. Entries in this
       table MUST be maintained in a persistent manner."
     ::= { g9983Port 2 }

   g9983PortCapEntry OBJECT-TYPE
     SYNTAX      G9983PortCapEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/TDIM port Capability table.
       Each entry represents an G.Bond/TDIM port indexed by the
       ifIndex. Additional capabilities are available via the
       gBondPortCapabilityEntry of GBOND-MIB.
       Note that a G.Bond/TDIM port runs on top of a single
       or multiple BCE port(s), which are also indexed by ifIndex."
     INDEX  { ifIndex }



Beili                  Expires September 13, 2012              [Page 18]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     ::= { g9983PortCapTable 1 }

   G9983PortCapEntry ::=
     SEQUENCE {
       g9983PortCapFecSupported                TruthValue,
       g9983PortCapFecMaxWordSize              Unsigned32,
       g9983PortCapFecMaxRedundancySize        Unsigned32,
       g9983PortCapFecInterleaverTypeSupported INTEGER,
       g9983PortCapFecMaxInterleaverDepth      Unsigned32
     }

   g9983PortCapFecSupported  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "FEC and Interleaver Capability of the G.Bond/TDIM port.
       This object has a value of true(1) when the port supports the
       FEC and Interleaver function.
       A value of false(2) is returned when the port does not
       support the FEC and Interleaver function.

       This object maps to the TR-159/G.998.3 attribute
       aFECSupported."
     REFERENCE
       "[TR-159] 5.5.4.4; [G.998.3] Appendix II, B-VI"
     ::= { g9983PortCapEntry 1 }

   g9983PortCapFecMaxWordSize  OBJECT-TYPE
     SYNTAX      Unsigned32(0|20..255)
     UNITS       "octets"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A Maximum supported FEC code word size in octets for the
       G.Bond/TDIM ports with FEC function.

       A value of zero SHALL be returned if the FEC is not supported.

       This object maps to TR-159 attribute aFECWordSize"
     REFERENCE
       "[TR-159] 5.5.4.11; [G.998.3] Appendix II, B-XI"
     ::= { g9983PortCapEntry 2 }

   g9983PortCapFecMaxRedundancySize  OBJECT-TYPE
     SYNTAX      Unsigned32(0|2|4|8|16|20)
     UNITS       "octets"
     MAX-ACCESS  read-only



Beili                  Expires September 13, 2012              [Page 19]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     STATUS      current
     DESCRIPTION
       "A Maximum supported FEC redundancy word size in octets for
       the G.Bond/TDIM ports with FEC function.

       A value of zero SHALL be returned if the FEC is not supported.

       This object maps to TR-159 attribute
       aFECMaxRedundancySize."
     REFERENCE
       "[TR-159] 5.5.4.12; [G.998.3] Appendix II, B-XII"
     ::= { g9983PortCapEntry 3 }

   g9983PortCapFecInterleaverTypeSupported  OBJECT-TYPE
     SYNTAX      INTEGER {
       none(0),
       block(1),
       convolution(2),
       blockConvolution(3)
     }
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "Supported Interleaver types for the G.Bond/TDIM ports with
       FEC function.

       Possible values are:
         none             - the port does not support interleaving
         block            - the port supports Block Interleaver
         convolution      - the port supports Convolution Interleaver
         blockConvolution - the port supports both Block and
                            Convolution Interleaver

       This object maps to TR-159 attribute
       aFECInterleaverTypesSupported."
     REFERENCE
       "[TR-159] 5.5.4.13; [G.998.3] Appendix II, B-XIII"
     ::= { g9983PortCapEntry 4 }

   g9983PortCapFecMaxInterleaverDepth  OBJECT-TYPE
     SYNTAX      Unsigned32(0|1|2|3|4|6|8|12|16|24|32|48|96)
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A Maximum Interleaver Depth for the G.Bond/TDIM ports with
       FEC function.

       A value of zero SHALL be returned if the Interleaver is not



Beili                  Expires September 13, 2012              [Page 20]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       supported.

       This object maps to TR-159 attribute aFECMaxInterleaverDepth."
     REFERENCE
       "[TR-159] 5.5.4.14; [G.998.3] Appendix II, B-XIV"
     ::= { g9983PortCapEntry 5 }


   g9983PortStatTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9983PortStatEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table provides overall status information of G.Bond
       TDIM ports, complementing the generic status information from
       the ifTable of IF-MIB and gBondFltStatus of GBOND-MIB.
       Additional status information about connected BCEs is
       available from the relevant line MIBs.

       This table contains live data from the equipment. As such,
       it is NOT persistent."
     ::= { g9983Port 3 }

   g9983PortStatEntry OBJECT-TYPE
     SYNTAX      G9983PortStatEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/TDIM port Status table.
       Each entry represents a G.Bond/TDIM port indexed by the
       ifIndex.
       Note that an G.Bond GBS port runs on top of a single
       or multiple BCE port(s), which are also indexed by ifIndex."
     INDEX  { ifIndex }
     ::= { g9983PortStatTable 1 }

   G9983PortStatEntry ::=
     SEQUENCE {
       g9983PortStatFecOperState         TruthValue,
       g9983PortStatFltStatus            BITS,
       g9983PortStatCrc4Errors           Counter32,
       g9983PortStatCrc6Errors           Counter32,
       g9983PortStatCrc8Errors           Counter32
     }

   g9983PortStatFecOperState  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-only



Beili                  Expires September 13, 2012              [Page 21]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     STATUS      current
     DESCRIPTION
       "A read-only value, indicating current operational state of
       the OPTIONAL Forward Error Correction (FEC) function for the
       G.998.3 port.
       A value of 'false' indicates that the FEC function is
       disabled. A value of 'true' indicates that the FEC function
       is enabled (and supported).

       This object maps to TR-159 attribute aFECOperState."
     REFERENCE
       "[TR-159] 5.5.4.6"
     ::= { g9983PortStatEntry 1 }

   g9983PortStatFltStatus  OBJECT-TYPE
     SYNTAX      BITS {
       serviceDown(0),
       wrongConfig(1)
     }
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "G.Bond/TDIM port Fault Status. This is a bitmap of possible
       conditions. The various bit positions are:
         serviceDown         - at least one of the services defined
                               for this aggregation group is down
                               (due to low rate).
         wrongConfig         - at least one BCE at the remote GBS-R
                               is already connected to another GBS.

       This object is intended to supplement ifOperStatus object
       in IF-MIB and gBondFltStatus in GBOND-MIB."
     REFERENCE
       "G.998.3 Section 6.3;
        IF-MIB, ifOperStatus; GBOND-MIB, gBondFltStatus"
     ::= { g9983PortStatEntry 2 }

   g9983PortStatCrc4Errors  OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The total number of CRC-4 errors (frame header error) on all
       pairs in the G.Bond/TDIM port. Simultaneous errors on M lines
       SHOULD be counted M times.

       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times



Beili                  Expires September 13, 2012              [Page 22]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB.

       This object maps to TR-159/G.998.3 attribute aCRC4Errors."
     REFERENCE
       "[TR-159] 5.5.4.1; [G.998.3] Appendix II, B-VII"
     ::= { g9983PortStatEntry 3 }

   g9983PortStatCrc6Errors  OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The total number of CRC-6 errors (super-frame error) on all
       pairs in the G.Bond/TDIM port. Simultaneous errors on M lines
       SHOULD be counted 1 time.

       Discontinuities in the value of this counter can occur at
       re-initialization of the local management subsystem, and at
       other times as indicated by the value of
       ifCounterDiscontinuityTime, defined in IF-MIB.

       This object maps to TR-159/G.998.3 attribute aCRC6Errors."
     REFERENCE
       "[TR-159] 5.5.4.2; [G.998.3] Appendix II, B-VIII"
     ::= { g9983PortStatEntry 4 }

   g9983PortStatCrc8Errors  OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The total number of CRC-8 errors (event/message error) on all
       pairs in the G.Bond/TDIM port. Simultaneous errors on M lines
       SHOULD be counted M times.

       Discontinuities in the value of this counter can occur at
       re-initialization of the local management subsystem, and at
       other times as indicated by the value of
       ifCounterDiscontinuityTime, defined in IF-MIB.

       This object maps to TR-159/G.998.3 attribute aCRC8Errors."
     REFERENCE
       "[TR-159] 5.5.4.3; [G.998.3] Appendix II, B-IX"
     ::= { g9983PortStatEntry 5 }


   g9983OperSvcTable OBJECT-TYPE



Beili                  Expires September 13, 2012              [Page 23]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     SYNTAX      SEQUENCE OF G9983OperSvcEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Table of the operational Services configured on a G.Bond/TDIM
       port. This table reflects current actual service configuration,
       set by the g9983PortConfAdminServices object. The number of
       entries (services) in this table therefore can vary between
       0, when no services are configured, and 60, for the maximum
       number of services.
       This table contains live data from the equipment. As such,
       it is NOT persistent."
     ::= { g9983Port 4 }

   g9983OperSvcEntry OBJECT-TYPE
     SYNTAX      G9983OperSvcEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/TDIM Port Operational Service table,
       containing the index of an active Service entry in the
       g9983SvcTable. The entry is indexed by ifIndex,
       indicating corresponding G.Bond/TDIM port, and by
       g9983OperSvcPosition (1..60), indicating the
       corresponding service position in the G.Bond/TDIM frame."
     INDEX  { ifIndex, g9983OperSvcPosition }
     ::= { g9983OperSvcTable 1 }

   G9983OperSvcEntry ::=
     SEQUENCE {
       g9983OperSvcPosition          G9983SvcOrderIndex,
       g9983OperSvcIdx               G9983SvcIndex,
       g9983OperSvcState             INTEGER
     }

   g9983OperSvcPosition OBJECT-TYPE
     SYNTAX      G9983SvcOrderIndex
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "G.Bond/TDIM operational Service position - a unique index,
       indicating relative placement of the associated service
       pointed by g9983OperSvcIdx, within the G.Bond/TDIM frame.

       There can be up to 60 services defined over TDIM bonded
       facility. Services with lower indices have higher priority in
       case of bandwidth degradation.




Beili                  Expires September 13, 2012              [Page 24]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       The value of g9983OperSvcPosition for the first
       g9983OperSvcEntry is always 1, incrementing sequentially
       for each consecutive entry, i.e. 2 for the second entry, 3 for
       the third etc.

       This objects maps to TR-159/G.998.3 attribute aServiceID."
     REFERENCE
       "[TR-159] 5.5.5.1; [G.998.3] Appendix II, C-I"
     ::= { g9983OperSvcEntry 1 }

   g9983OperSvcIdx OBJECT-TYPE
     SYNTAX      G9983SvcIndex
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "G.Bond/TDIM operational Service index - a read-only pointer to
       an existing entry in the g9983SvcTable (value of
       g9983SvcIdx), describing a particular service."
     ::= { g9983OperSvcEntry 2 }

   g9983OperSvcState  OBJECT-TYPE
     SYNTAX      INTEGER {
       up(1),
       down(2)
     }
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "G.Bond/TDIM Service Operational State.

       Possible values are:
         up                  - Service is up passing traffic.
         down                - Service is down, due to a variety of
                               reasons, e.g. G.Bond/TDIM port is
                               down, current link bandwidth is too
                               low to support a particular service,
                               etc.
       This objects maps to TR-159 attribute aServiceOperState."
     REFERENCE
       "[TR-159] 5.5.5.5"
     ::= { g9983OperSvcEntry 3 }


   g9983SvcTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9983SvcEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION



Beili                  Expires September 13, 2012              [Page 25]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       "Table of possible Services for a G.Bond/TDIM ports.
       Entries in this table MUST be maintained in a persistent
       manner"
     ::= { g9983Port 5 }

   g9983SvcEntry OBJECT-TYPE
     SYNTAX      G9983SvcEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/TDIM Port Service table, containing
       the management information applicable to a particular Service,
       indexed by the g9983SvcIdx, on a G.Bond/TDIM port,
       indexed by the ifIndex."
     INDEX  { ifIndex, g9983SvcIdx }
     ::= { g9983SvcTable 1 }

   G9983SvcEntry ::=
     SEQUENCE {
       g9983SvcIdx           G9983SvcIndex,
       g9983SvcIfIdx         InterfaceIndex,
       g9983SvcType          INTEGER,
       g9983SvcSize          Unsigned32,
       g9983SvcRowStatus     RowStatus
     }

   g9983SvcIdx OBJECT-TYPE
     SYNTAX      G9983SvcIndex
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "G.Bond/TDIM Service index - a unique index associated with
       a particular service entry."
     ::= { g9983SvcEntry 1 }

   g9983SvcIfIdx OBJECT-TYPE
     SYNTAX      InterfaceIndex
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "This is a unique index within the ifTable. It represents
       the interface index of a service to be transmitted over the
       G.Bond/TDIM service instance.

       This objects maps to TR-159 attribute aServiceIfIndex."
     REFERENCE
       "[TR-159] 5.5.5.2"
     ::= { g9983SvcEntry 2 }



Beili                  Expires September 13, 2012              [Page 26]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


   g9983SvcType  OBJECT-TYPE
     SYNTAX      INTEGER {
       ds1(0),
       e1(1),
       nxds0(2),
       nxe0(3),
       ds3(4),
       e3(5),
       clock(6),
       ethernet(7),
       atm(8),
       gfpNoFCS(9),
       gfp(10)
     }
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "G.Bond/TDIM Service Type.

       Possible values are:
         ds1            - Clear Channel DS1 (synchronous)
         e1             - Clear Channel E1 (synchronous)
         nxds0          - Fractional DS1 (synchronous)
         nxe0           - Fractional E1 (synchronous)
         ds3            - DS3 (synchronous)
         e3             - E3 (synchronous)
         clock          - Clock transfer (synchronous)
         ethernet       - Ethernet (asynchronous)
         atm            - ATM (asynchronous)
         gfpNoFCS       - GFP encapsulated without FCS (asynchronous)
         gfp            - GFP encapsulated with FCS (asynchronous)

       For the GBS-R ports, the value of this object cannot be
       changed directly. This value may be changed as a result of
       writing operation on the g9983SvcType object of a
       remote GBS-C.

       Attempts to change this object MUST be rejected for the GBS-R
       ports.

       This object maps to TR-159/G.998.3 attribute aServiceType."
     REFERENCE
       "[TR-159] 5.5.5.3; [G.998.3] Appendix II, C-II"
     ::= { g9983SvcEntry 3 }

   g9983SvcSize  OBJECT-TYPE
     SYNTAX      Unsigned32(0|20..255)
     UNITS       "octets"



Beili                  Expires September 13, 2012              [Page 27]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "Service size in octets per bonding sub-block for a specific
       service identified by g9983SvcIdx.

       For TDM (synchronous) services with variable size
       e.g. fractional DS1/E1 - this object represents the number of
       DS0/E0 channels.
       For asynchronous services (Ethernet, ATM, GFPnoFCS or GFP) -
       this object represents max. number of octets.
       For non-fractional TDM services, i.e. DS1, E1, DS3, E3 and
       Clock, the value of this object MUST be 0.

       A GET operation returns current value.
       A SET operation, allowed on GBS-C ports, changes the service
       size to the indicated value. If the service type is a fixed
       rate synchronous service (g9983SvcType is nxds0, nxe0,
       ds1, e1, ds3, e3 or clock), the operation MUST be rejected.

       This object maps to TR-159/G.998.3 attribute aServiceSize."
     REFERENCE
       "[TR-159] 5.5.5.4; [G.998.3] Appendix II, C-III"
     ::= { g9983SvcEntry 4 }

   g9983SvcRowStatus  OBJECT-TYPE
     SYNTAX      RowStatus
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "This object controls the creation, modification, or deletion
       of the associated entry in the g9983SvcTable per the
       semantics of RowStatus.

       If an 'active' entry is referenced via g9983OperSvcIdx
       or g9983PortConfAdminServices instance or indexes a
       g9983SvcPm*Entry, the entry MUST remain
       'active'.

       An 'active' entry SHALL NOT be modified. In order to modify an
       existing entry, it MUST be taken out of service (by setting
       this object to 'notInService'), modified, and set 'active'
       again."
     ::= { g9983SvcEntry 5 }


   -------------------------------
   -- Performance Monitoring group



Beili                  Expires September 13, 2012              [Page 28]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


   -------------------------------

   g9983PM   OBJECT IDENTIFIER ::= { g9983Port 6 }

   g9983PortPmCurTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9983PortPmCurEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table contains current Performance Monitoring information
       for a G.Bond/TDIM port. This table contains live data from the
       equipment and as such is NOT persistent."
     ::= { g9983PM 1 }

   g9983PortPmCurEntry OBJECT-TYPE
     SYNTAX      G9983PortPmCurEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/TDIM Port PM table.
       Each entry represents a G.Bond/TDIM port indexed by the
       ifIndex."
     INDEX  { ifIndex }
     ::= { g9983PortPmCurTable 1 }

   G9983PortPmCurEntry ::=
     SEQUENCE {
       g9983PortPmCur15MinValidIntervals   HCPerfValidIntervals,
       g9983PortPmCur15MinInvalidIntervals HCPerfInvalidIntervals,
       g9983PortPmCur15MinTimeElapsed      HCPerfTimeElapsed,
       g9983PortPmCur15MinCrc4s            HCPerfCurrentCount,
       g9983PortPmCur15MinCrc6s            HCPerfCurrentCount,
       g9983PortPmCur15MinCrc8s            HCPerfCurrentCount,
       g9983PortPmCur1DayValidIntervals    Unsigned32,
       g9983PortPmCur1DayInvalidIntervals  Unsigned32,
       g9983PortPmCur1DayTimeElapsed       HCPerfTimeElapsed,
       g9983PortPmCur1DayCrc4s             HCPerfCurrentCount,
       g9983PortPmCur1DayCrc6s             HCPerfCurrentCount,
       g9983PortPmCur1DayCrc8s             HCPerfCurrentCount
     }

   g9983PortPmCur15MinValidIntervals  OBJECT-TYPE
     SYNTAX      HCPerfValidIntervals
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only number of 15-minute intervals for which the
       performance data was collected. The value of this object will



Beili                  Expires September 13, 2012              [Page 29]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       be 96 or the maximum number of 15-minute history intervals
       collected by the implementation unless the measurement was
       (re-)started recently, in which case the value will be the
       number of complete 15 minutes intervals for which there are at
       least some data.
       In certain cases it is possible that some intervals are
       unavailable. In this case, this object reports the maximum
       interval number for which data is available.

       This object partially maps to the TR-159 attribute
       aGroupPerf15MinValidIntervals."
     REFERENCE
       "[TR-159] 5.5.1.32"
     ::= { g9983PortPmCurEntry 1 }

   g9983PortPmCur15MinInvalidIntervals  OBJECT-TYPE
     SYNTAX      HCPerfInvalidIntervals
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only number of 15-minute intervals for which the
       performance data was not always available. The value will
       typically be zero except in cases where the data for some
       intervals are not available.

       This object partially maps to the TR-159 attribute
       aGroupPerf15MinInvalidIntervals."
     REFERENCE
       "[TR-159] 5.5.1.33"
     ::= { g9983PortPmCurEntry 2 }

   g9983PortPmCur15MinTimeElapsed  OBJECT-TYPE
     SYNTAX      HCPerfTimeElapsed
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds that have elapsed since the
       beginning of the current 15-minute performance interval.

       This object partially maps to the TR-159 attribute
       aGroupPerfCurr15MinTimeElapsed."
     REFERENCE
       "[TR-159] 5.5.1.34"
     ::= { g9983PortPmCurEntry 3 }

   g9983PortPmCur15MinCrc4s  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount



Beili                  Expires September 13, 2012              [Page 30]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of CRC-4 errors (frame header errors) on all
       active pairs in the G.Bond/TDIM port during the current
       15-minute performance interval.
       Simultaneous errors on M lines SHOULD be counted M times.

       Note that the total number of CRC-4 errors is indicated by the
       g9983PortStatCrc4Errors object.

       This object is inhibited during Severely Errored Seconds (SES)
       or Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.4.1"
     ::= { g9983PortPmCurEntry 4}

   g9983PortPmCur15MinCrc6s  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of CRC-6 errors (super-frame errors) on all
       active pairs in the G.Bond/TDIM port during the current
       15-minute performance interval.
       Simultaneous errors on M lines SHOULD be counted 1 time.

       Note that the total number of CRC-6 errors is indicated by the
       g9983PortStatCrc6Errors object.

       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.4.2"
     ::= { g9983PortPmCurEntry 5}

   g9983PortPmCur15MinCrc8s  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of CRC-8 errors (event/message errors) on all
       active pairs in the G.Bond/TDIM port during the current
       15-minute performance interval.
       Simultaneous errors on M lines SHOULD be counted M times.

       Note that the total number of CRC-8 errors is indicated by the
       g9983PortStatCrc8Errors object.




Beili                  Expires September 13, 2012              [Page 31]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       This object is inhibited during Unavailable Seconds (UAS)."
     REFERENCE
       "[TR-159] 5.5.4.3"
     ::= { g9983PortPmCurEntry 6}

   g9983PortPmCur1DayValidIntervals  OBJECT-TYPE
     SYNTAX      Unsigned32 (0..7)
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only number of 1-day intervals for which data was
       collected. The value of this object will be 7 or the maximum
       number of 1-day history intervals collected by the
       implementation unless the measurement was (re-)started recently,
       in which case the value will be the number of complete 1-day
       intervals for which there are at least some data.
       In certain cases it is possible that some intervals are
       unavailable. In this case, this object reports the maximum
       interval number for which data is available."
     REFERENCE
       "[TR-159] 5.5.1.45"
     ::= { g9983PortPmCurEntry 7 }

   g9983PortPmCur1DayInvalidIntervals  OBJECT-TYPE
     SYNTAX      Unsigned32 (0..7)
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only number of 1-day intervals for which data was
       not always available. The value will typically be zero except in
       cases where the data for some intervals are not available."
     REFERENCE
       "[TR-159] 5.5.1.46"
     ::= { g9983PortPmCurEntry 8 }

   g9983PortPmCur1DayTimeElapsed  OBJECT-TYPE
     SYNTAX      HCPerfTimeElapsed
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds that have elapsed since the
       beginning of the current 1-day performance interval."
     REFERENCE
       "[TR-159] 5.5.1.47"
     ::= { g9983PortPmCurEntry 9 }

   g9983PortPmCur1DayCrc4s  OBJECT-TYPE



Beili                  Expires September 13, 2012              [Page 32]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     SYNTAX      HCPerfCurrentCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of CRC-4 errors on the G.Bond/TDIM port in
       the current 1-day performance interval.

       This object is inhibited during Severely Errored Seconds (SES)
       and Unavailable Seconds (UAS)."
     ::= { g9983PortPmCurEntry 10 }

   g9983PortPmCur1DayCrc6s  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of CRC-6 errors on the G.Bond/TDIM port
       in the current 1-day performance interval.

       This object is inhibited during Unavailable Seconds (UAS)."
     ::= { g9983PortPmCurEntry 11 }

   g9983PortPmCur1DayCrc8s  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count ofCRC-8 on the G.Bond/TDIM port in
       the current 1-day performance interval.

       This object is inhibited during Unavailable Seconds (UAS)."
     ::= { g9983PortPmCurEntry 12 }

   -- Port PM history: 15-min buckets

   g9983PortPm15MinTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9983PortPm15MinEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table contains historical 15-minute buckets of Performance
       Monitoring information for a G.Bond/TDIM port (a row for each
       15-minute interval, up to 96 intervals).
       Entries in this table MUST be maintained in a persistent manner."
     ::= { g9983PM 2 }

   g9983PortPm15MinEntry OBJECT-TYPE
     SYNTAX      G9983PortPm15MinEntry



Beili                  Expires September 13, 2012              [Page 33]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/TDIM Port historical 15-minute PM table.
       Each entry represents performance monitoring data for a G.Bond
       TDIM port, indexed by ifIndex, collected during a particular
       15-minute interval, indexed by
       g9983PortPm15MinIntervalIndex."
     INDEX  { ifIndex, g9983PortPm15MinIntervalIndex }
     ::= { g9983PortPm15MinTable 1 }

   G9983PortPm15MinEntry ::=
     SEQUENCE {
       g9983PortPm15MinIntervalIndex      Unsigned32,
       g9983PortPm15MinIntervalMoniTime   HCPerfTimeElapsed,
       g9983PortPm15MinIntervalCrc4s      HCPerfIntervalCount,
       g9983PortPm15MinIntervalCrc6s      HCPerfIntervalCount,
       g9983PortPm15MinIntervalCrc8s      HCPerfIntervalCount,
       g9983PortPm15MinIntervalValid      TruthValue
     }

   g9983PortPm15MinIntervalIndex  OBJECT-TYPE
     SYNTAX      Unsigned32 (1..96)
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Performance Data Interval number. 1 is the most recent previous
       interval; interval 96 is 24 hours ago.
       Intervals 2..96 are OPTIONAL.

       This object partially maps to the TR-159 attribute
       aGroupPerf15MinIntervalNumber."
     REFERENCE
       "[TR-159] 5.5.1.57"
     ::= { g9983PortPm15MinEntry 1 }

   g9983PortPm15MinIntervalMoniTime  OBJECT-TYPE
     SYNTAX      HCPerfTimeElapsed
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds over which the performance data
       was actually monitored. This value will be the same as the
       interval duration (900 seconds), except in a situation where
       performance data could not be collected for any reason."
     ::= { g9983PortPm15MinEntry 2 }




Beili                  Expires September 13, 2012              [Page 34]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


   g9983PortPm15MinIntervalCrc4s  OBJECT-TYPE
     SYNTAX      HCPerfIntervalCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of CRC-4 errors on the G.Bond/TDIM port
       during the 15-minute performance history interval.

       This object is inhibited during Severely Errored Seconds (SES)
       and Unavailable Seconds (UAS)."
     ::= { g9983PortPm15MinEntry 3 }

   g9983PortPm15MinIntervalCrc6s  OBJECT-TYPE
     SYNTAX      HCPerfIntervalCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of CRC-6 erorrs on the G.Bond/TDIM port
       during the 15-minute performance history interval.

       This object is inhibited during Unavailable Seconds (UAS)."
     ::= { g9983PortPm15MinEntry 4 }

   g9983PortPm15MinIntervalCrc8s  OBJECT-TYPE
     SYNTAX      HCPerfIntervalCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of CRC-8 errors on the G.Bond/TDIM port
       during the current 15-minute performance interval.

       This object is inhibited during Unavailable Seconds (UAS)."
     ::= { g9983PortPm15MinEntry 5 }

   g9983PortPm15MinIntervalValid  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only object indicating whether or not this history
       bucket contains valid data. Valid bucket is reported as true(1)
       and invalid bucket as false(2).
       If this history bucket is invalid the BTU-C MUST NOT produce
       notifications based upon the value of the counters in this
       bucket.
       Note that an implementation may decide not to store invalid
       history buckets in its data base. In such case this object is
       not required as only valid history buckets are available while



Beili                  Expires September 13, 2012              [Page 35]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       invalid history buckets are simply not in the data base.

       This object partially maps to the TR-159 attribute
       aGroupPerf15MinIntervalValid."
     REFERENCE
       "[TR-159] 5.5.1.58"
     ::= { g9983PortPm15MinEntry 6 }

   -- Port PM history: 1-day buckets

   g9983PortPm1DayTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9983PortPm1DayEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table contains historical 1-day buckets of Performance
       Monitoring information for a G.Bond/TDIM port (a row for each
       1-day interval, up to 7 intervals).
       Entries in this table MUST be maintained in a persistent manner."
     ::= { g9983PM 3 }

   g9983PortPm1DayEntry OBJECT-TYPE
     SYNTAX      G9983PortPm1DayEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/TDIM port historical 1-day PM table.
       Each entry represents performance monitoring data for such port,
       indexed by ifIndex, collected during a particular 1-day
       interval, indexed by g9983PortPm1DayIntervalIndex."
     INDEX  { ifIndex, g9983PortPm1DayIntervalIndex }
     ::= { g9983PortPm1DayTable 1 }

   G9983PortPm1DayEntry ::=
     SEQUENCE {
       g9983PortPm1DayIntervalIndex      Unsigned32,
       g9983PortPm1DayIntervalMoniTime   HCPerfTimeElapsed,
       g9983PortPm1DayIntervalCrc4s      HCPerfIntervalCount,
       g9983PortPm1DayIntervalCrc6s      HCPerfIntervalCount,
       g9983PortPm1DayIntervalCrc8s      HCPerfIntervalCount,
       g9983PortPm1DayIntervalValid      TruthValue
     }

   g9983PortPm1DayIntervalIndex  OBJECT-TYPE
     SYNTAX      Unsigned32 (1..7)
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION



Beili                  Expires September 13, 2012              [Page 36]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       "Performance Data Interval number. 1 is the most recent previous
       interval; interval 7 is 7 days ago.
       Intervals 2..7 are OPTIONAL.

       This object partially maps to the TR-159 attribute
       aGroupPerf1DayIntervalNumber."
     REFERENCE
       "[TR-159] 5.5.1.62"
     ::= { g9983PortPm1DayEntry 1 }

   g9983PortPm1DayIntervalMoniTime  OBJECT-TYPE
     SYNTAX      HCPerfTimeElapsed
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds over which the performance data
       was actually monitored. This value will be the same as the
       interval duration (86400 seconds), except in a situation where
       performance data could not be collected for any reason.

       This object partially maps to the TR-159 attribute
       aGroupPerf1DayIntervalMoniSecs."
     REFERENCE
       "[TR-159] 5.5.1.64"
     ::= { g9983PortPm1DayEntry 2 }

   g9983PortPm1DayIntervalCrc4s  OBJECT-TYPE
     SYNTAX      HCPerfIntervalCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of CRC-4 errors on the G.Bond/TDIM port
       during the 1-day performance history interval.

       This object is inhibited during Severely Errored Seconds (SES)
       and Unavailable Seconds (UAS)."
     ::= { g9983PortPm1DayEntry 3 }

   g9983PortPm1DayIntervalCrc6s  OBJECT-TYPE
     SYNTAX      HCPerfIntervalCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of CRC-6 errors on the G.Bond/TDIM port
       during the 1-day performance history interval.

       This object is inhibited during Unavailable Seconds (UAS)."



Beili                  Expires September 13, 2012              [Page 37]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     ::= { g9983PortPm1DayEntry 4 }

   g9983PortPm1DayIntervalCrc8s  OBJECT-TYPE
     SYNTAX      HCPerfIntervalCount
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of CRC-6 errors on the G.Bond/TDIM port
       during the current 1-day performance interval.

       This object is inhibited during Unavailable Seconds (UAS)."
     ::= { g9983PortPm1DayEntry 5 }

   g9983PortPm1DayIntervalValid  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only object indicating whether or not this history
       bucket contains valid data. Valid bucket is reported as true(1)
       and invalid bucket as false(2).
       If this history bucket is invalid the BTU-C MUST NOT produce
       notifications based upon the value of the counters in this
       bucket.
       Note that an implementation may decide not to store invalid
       history buckets in its data base. In such case this object is
       not required as only valid history buckets are available while
       invalid history buckets are simply not in the data base.

       This object partially maps to the TR-159 attribute
       aGroupPerf1DayIntervalValid."
     REFERENCE
       "[TR-159] 5.5.1.63"
     ::= { g9983PortPm1DayEntry 6 }

   -- Services PM

   g9983SvcPmCurTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9983SvcPmCurEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table contains current Performance Monitoring information
       for the services of a G.Bond/TDIM port.
       This table contains live data from the equipment and as such is
       NOT persistent."
     ::= { g9983PM 4 }




Beili                  Expires September 13, 2012              [Page 38]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


   g9983SvcPmCurEntry OBJECT-TYPE
     SYNTAX      G9983SvcPmCurEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/TDIM Services PM table.
       Each entry represents a service, indexed by the
       g9983SvcIdx, in a G.Bond/TDIM port, indexed by the
       ifIndex."
     INDEX  { ifIndex, g9983SvcIdx }
     ::= { g9983SvcPmCurTable 1 }

   G9983SvcPmCurEntry ::=
     SEQUENCE {
       g9983SvcPmCur15MinValidIntervals   HCPerfValidIntervals,
       g9983SvcPmCur15MinInvalidIntervals HCPerfInvalidIntervals,
       g9983SvcPmCur15MinTimeElapsed      HCPerfTimeElapsed,
       g9983SvcPmCur15MinDowns            HCPerfCurrentCount,
       g9983SvcPmCur1DayValidIntervals    Unsigned32,
       g9983SvcPmCur1DayInvalidIntervals  Unsigned32,
       g9983SvcPmCur1DayTimeElapsed       HCPerfTimeElapsed,
       g9983SvcPmCur1DayDowns             HCPerfCurrentCount
     }

   g9983SvcPmCur15MinValidIntervals  OBJECT-TYPE
     SYNTAX      HCPerfValidIntervals
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only number of 15-minute intervals for which the
       performance data was collected. The value of this object will
       be 96 or the maximum number of 15-minute history intervals
       collected by the implementation unless the measurement was
       (re-)started recently, in which case the value will be the
       number of complete 15 minutes intervals for which there are at
       least some data.
       In certain cases it is possible that some intervals are
       unavailable. In this case, this object reports the maximum
       interval number for which data is available.

       This object partially maps to the TR-159 attribute
       aGroupPerf15MinValidIntervals."
     REFERENCE
       "[TR-159] 5.5.1.32"
     ::= { g9983SvcPmCurEntry 1 }

   g9983SvcPmCur15MinInvalidIntervals  OBJECT-TYPE
     SYNTAX      HCPerfInvalidIntervals



Beili                  Expires September 13, 2012              [Page 39]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only number of 15-minute intervals for which the
       performance data was not always available. The value will
       typically be zero except in cases where the data for some
       intervals are not available.

       This object partially maps to the TR-159 attribute
       aGroupPerf15MinInvalidIntervals."
     REFERENCE
       "[TR-159] 5.5.1.33"
     ::= { g9983SvcPmCurEntry 2 }

   g9983SvcPmCur15MinTimeElapsed  OBJECT-TYPE
     SYNTAX      HCPerfTimeElapsed
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds that have elapsed since the
       beginning of the current 15-minute performance interval.

       This object partially maps to the TR-159 attribute
       aGroupPerfCurr15MinTimeElapsed."
     REFERENCE
       "[TR-159] 5.5.1.34"
     ::= { g9983SvcPmCurEntry 3 }

   g9983SvcPmCur15MinDowns  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds in the current 15-minute
       performance interval, during which a particular TDIM
       Service was 'down', as indicated by the
       g9983OperSvcState object.

       This object is inhibited during Unavailable Seconds (UAS)."
     ::= { g9983SvcPmCurEntry 4}

   g9983SvcPmCur1DayValidIntervals  OBJECT-TYPE
     SYNTAX      Unsigned32 (0..7)
     UNITS       "days"
     MAX-ACCESS  read-only
     STATUS      current



Beili                  Expires September 13, 2012              [Page 40]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     DESCRIPTION
       "A read-only number of 1-day performance history intervals for
       which the data was collected. The value of this object will be
       7 or the maximum number of 1-day history intervals collected by
       the implementation unless the measurement was (re-)started
       recently, in which case the value will be the number of complete
       1-day intervals for which there are at least some data.
       In certain cases it is possible that some intervals are
       unavailable. In this case, this object reports the maximum
       interval number for which data is available."
     REFERENCE
       "[TR-159] 5.5.1.45"
     ::= { g9983SvcPmCurEntry 5 }

   g9983SvcPmCur1DayInvalidIntervals  OBJECT-TYPE
     SYNTAX      Unsigned32 (0..7)
     UNITS       "days"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only number of 1-day performance history intervals for
       which the performance data was not always available. The value
       will typically be zero except in cases where the data for some
       intervals are not available."
     REFERENCE
       "[TR-159] 5.5.1.46"
     ::= { g9983SvcPmCurEntry 6 }

   g9983SvcPmCur1DayTimeElapsed  OBJECT-TYPE
     SYNTAX      HCPerfTimeElapsed
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds that have elapsed since the
       beginning of the current 1-day performance interval."
     REFERENCE
       "[TR-159] 5.5.1.47"
     ::= { g9983SvcPmCurEntry 7 }

   g9983SvcPmCur1DayDowns  OBJECT-TYPE
     SYNTAX      HCPerfCurrentCount
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds in the current 1-day performance
       interval, during which a particular TDIM Service was



Beili                  Expires September 13, 2012              [Page 41]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       'down', as indicated by the g9983OperSvcState object.

       This object is inhibited during Unavailable Seconds (UAS)."
     ::= { g9983SvcPmCurEntry 8 }

   -- Service PM history: 15-min buckets

   g9983SvcPm15MinTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9983SvcPm15MinEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table contains historical 15-minute buckets of Performance
       Monitoring information for the Services of a G.Bond/TDIM port
       (a multi-dimensional row for each 15-minute interval, up to 96
       intervals).

       Entries in this table MUST be maintained in a persistent manner."
     ::= { g9983PM 5 }

   g9983SvcPm15MinEntry OBJECT-TYPE
     SYNTAX      G9983SvcPm15MinEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/TDIM Services historical 15-minute PM
       table.
       Each entry represents performance monitoring data for a
       particular Service, indexed by g9983SvcIdx, in a G.Bond
       TDIM port, indexed by ifIndex, collected during a particular
       15-minute interval, indexed by
       g9983SvcPm15MinIntervalIndex."
     INDEX  { ifIndex, g9983SvcIdx,
              g9983SvcPm15MinIntervalIndex }
     ::= { g9983SvcPm15MinTable 1 }

   G9983SvcPm15MinEntry ::=
     SEQUENCE {
       g9983SvcPm15MinIntervalIndex      Unsigned32,
       g9983SvcPm15MinIntervalMoniTime   HCPerfTimeElapsed,
       g9983SvcPm15MinIntervalDowns      HCPerfIntervalCount,
       g9983SvcPm15MinIntervalValid      TruthValue
     }

   g9983SvcPm15MinIntervalIndex  OBJECT-TYPE
     SYNTAX      Unsigned32 (1..96)
     MAX-ACCESS  not-accessible
     STATUS      current



Beili                  Expires September 13, 2012              [Page 42]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     DESCRIPTION
       "Performance Data Interval number. 1 is the most recent previous
       interval; interval 96 is 24 hours ago.
       Intervals 2..96 are OPTIONAL.

       This object partially maps to the TR-159 attribute
       aGroupPerf15MinIntervalNumber."
     REFERENCE
       "[TR-159] 5.5.1.57"
     ::= { g9983SvcPm15MinEntry 1 }

   g9983SvcPm15MinIntervalMoniTime  OBJECT-TYPE
     SYNTAX      HCPerfTimeElapsed
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds over which the performance data
       was actually monitored. This value will be the same as the
       interval duration (900 seconds), except in a situation where
       performance data could not be collected for any reason."
     ::= { g9983SvcPm15MinEntry 2 }

   g9983SvcPm15MinIntervalDowns  OBJECT-TYPE
     SYNTAX      HCPerfIntervalCount
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds in the 15-minute performance
       history interval, during which a particular TDIM Service was
       'down', as indicated by the g9983OperSvcState object.

       This object is inhibited during Unavailable Seconds (UAS)."
     ::= { g9983SvcPm15MinEntry 3 }

   g9983SvcPm15MinIntervalValid  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only object indicating whether or not this history
       bucket contains valid data. Valid bucket is reported as true(1)
       and invalid bucket as false(2).
       If this history bucket is invalid the BTU-C MUST NOT produce
       notifications based upon the value of the counters in this
       bucket.
       Note that an implementation may decide not to store invalid



Beili                  Expires September 13, 2012              [Page 43]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       history buckets in its data base. In such case this object is
       not required as only valid history buckets are available while
       invalid history buckets are simply not in the data base.

       This object partially maps to the TR-159 attribute
       aGroupPerf15MinIntervalValid."
     REFERENCE
       "[TR-159] 5.5.1.58"
     ::= { g9983SvcPm15MinEntry 4 }

   -- Service PM history: 1-day buckets

   g9983SvcPm1DayTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF G9983SvcPm1DayEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table contains historical 1-day buckets of Performance
       Monitoring information for the Services of a G.Bond/TDIM port
       (a multi-dimensional row for each 1-day interval, up to 7
       intervals).
       Entries in this table MUST be maintained in a persistent manner."
     ::= { g9983PM 6 }

   g9983SvcPm1DayEntry OBJECT-TYPE
     SYNTAX      G9983SvcPm1DayEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the G.Bond/TDIM Service historical 1-day PM table.
       Each entry represents performance monitoring data for a
       particular Service, indexed by g9983SvcIdx, defined in a
       G.Bond/TDIM port, indexed by ifIndex, collected during a
       particular 1-day interval, indexed by
       g9983SvcPm1DayIntervalIndex."
     INDEX  { ifIndex, g9983SvcIdx,
              g9983SvcPm1DayIntervalIndex }
     ::= { g9983SvcPm1DayTable 1 }

   G9983SvcPm1DayEntry ::=
     SEQUENCE {
       g9983SvcPm1DayIntervalIndex       Unsigned32,
       g9983SvcPm1DayIntervalMoniTime    HCPerfTimeElapsed,
       g9983SvcPm1DayIntervalDowns       HCPerfIntervalCount,
       g9983SvcPm1DayIntervalValid       TruthValue
     }

   g9983SvcPm1DayIntervalIndex  OBJECT-TYPE



Beili                  Expires September 13, 2012              [Page 44]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     SYNTAX      Unsigned32 (1..7)
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Performance Data Interval number. 1 is the most recent previous
       interval; interval 7 is 7 days ago.
       Intervals 2..7 are OPTIONAL.

       This object partially maps to the TR-159 attribute
       aGroupPerf1DayIntervalNumber."
     REFERENCE
       "[TR-159] 5.5.1.62"
     ::= { g9983SvcPm1DayEntry 1 }

   g9983SvcPm1DayIntervalMoniTime  OBJECT-TYPE
     SYNTAX      HCPerfTimeElapsed
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds over which the performance data
       was actually monitored. This value will be the same as the
       interval duration (86400 seconds), except in a situation where
       performance data could not be collected for any reason.

       This object partially maps to the TR-159 attribute
       aGroupPerf1DayIntervalMoniSecs."
     REFERENCE
       "[TR-159] 5.5.1.64"
     ::= { g9983SvcPm1DayEntry 2 }

   g9983SvcPm1DayIntervalDowns  OBJECT-TYPE
     SYNTAX      HCPerfIntervalCount
     UNITS       "seconds"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "A read-only count of seconds in the 1-day performance history
       interval, during which a particular TDIM Service was 'down',
       as indicated by the g9983OperSvcState object.

       This object is inhibited during Unavailable Seconds (UAS)."
     ::= { g9983SvcPm1DayEntry 3 }

   g9983SvcPm1DayIntervalValid  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-only
     STATUS      current



Beili                  Expires September 13, 2012              [Page 45]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


     DESCRIPTION
       "A read-only object indicating whether or not this history
       bucket contains valid data. Valid bucket is reported as true(1)
       and invalid bucket as false(2).
       If this history bucket is invalid the BTU-C MUST NOT produce
       notifications based upon the value of the counters in this
       bucket.
       Note that an implementation may decide not to store invalid
       history buckets in its data base. In such case this object is
       not required as only valid history buckets are available while
       invalid history buckets are simply not in the data base.

       This object partially maps to the TR-159 attribute
       aGroupPerf1DayIntervalValid."
     REFERENCE
       "[TR-159] 5.5.1.63"
     ::= { g9983SvcPm1DayEntry 4 }


  --
  -- Conformance Statements
  --

   g9983Groups      OBJECT IDENTIFIER
     ::= { g9983Conformance 1 }

   g9983Compliances OBJECT IDENTIFIER
     ::= { g9983Conformance 2 }

   -- Object Groups

   g9983BasicGroup OBJECT-GROUP
     OBJECTS {
       g9983PortConfAdminServices,
       g9983PortStatCrc4Errors,
       g9983PortStatCrc6Errors,
       g9983PortStatCrc8Errors,
       g9983PortCapFecSupported,
       g9983OperSvcIdx,
       g9983OperSvcState,
       g9983SvcIfIdx,
       g9983SvcType,
       g9983SvcSize,
       g9983SvcRowStatus,
       g9983PortStatFltStatus
     }
     STATUS      current
     DESCRIPTION



Beili                  Expires September 13, 2012              [Page 46]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       "A collection of objects representing management information
       for G.Bond/TDIM ports."
     ::= { g9983Groups 1 }

   g9983FecGroup OBJECT-GROUP
     OBJECTS {
       g9983PortCapFecSupported,
       g9983PortConfFecAdminState,
       g9983PortStatFecOperState,
       g9983PortConfFecWordSize,
       g9983PortConfFecRedundancySize,
       g9983PortConfFecInterleaverType,
       g9983PortConfFecInterleaverDepth,
       g9983PortCapFecMaxWordSize,
       g9983PortCapFecMaxRedundancySize,
       g9983PortCapFecInterleaverTypeSupported,
       g9983PortCapFecMaxInterleaverDepth
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects supporting OPTIONAL Forward Error
       Correction (FEC) and Interleaver function in G.Bond/TDIM
       ports."
     ::= { g9983Groups 2 }

   g9983AlarmConfGroup OBJECT-GROUP
     OBJECTS {
       g9983PortConfSvcUpDownEnable
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects required for configuration of alarm
       thresholds and notifications in G.Bond/TDIM ports."
     ::= { g9983Groups 3 }

   g9983NotificationGroup NOTIFICATION-GROUP
     NOTIFICATIONS {
       g9983SvcUp,
       g9983SvcDown
     }
     STATUS      current
     DESCRIPTION
       "This group supports notifications of significant conditions
       associated with G.Bond/TDIM ports."
     ::= { g9983Groups 4 }

   g9983PerfCurrGroup OBJECT-GROUP
     OBJECTS {



Beili                  Expires September 13, 2012              [Page 47]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       g9983PortPmCur15MinValidIntervals,
       g9983PortPmCur15MinInvalidIntervals,
       g9983PortPmCur15MinTimeElapsed,
       g9983PortPmCur15MinCrc4s,
       g9983PortPmCur15MinCrc6s,
       g9983PortPmCur15MinCrc8s,
       g9983PortPmCur1DayValidIntervals,
       g9983PortPmCur1DayInvalidIntervals,
       g9983PortPmCur1DayTimeElapsed,
       g9983PortPmCur1DayCrc4s,
       g9983PortPmCur1DayCrc6s,
       g9983PortPmCur1DayCrc8s,
       g9983SvcPmCur15MinValidIntervals,
       g9983SvcPmCur15MinInvalidIntervals,
       g9983SvcPmCur15MinTimeElapsed,
       g9983SvcPmCur15MinDowns,
       g9983SvcPmCur1DayValidIntervals,
       g9983SvcPmCur1DayInvalidIntervals,
       g9983SvcPmCur1DayTimeElapsed,
       g9983SvcPmCur1DayDowns
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects supporting OPTIONAL current Performance
       Monitoring information for G.Bond/TDIM ports."
     ::= { g9983Groups 5 }

   g9983Perf15MinGroup OBJECT-GROUP
     OBJECTS {
       g9983PortPm15MinIntervalMoniTime,
       g9983PortPm15MinIntervalCrc4s,
       g9983PortPm15MinIntervalCrc6s,
       g9983PortPm15MinIntervalCrc8s,
       g9983PortPm15MinIntervalValid,
       g9983SvcPm15MinIntervalMoniTime,
       g9983SvcPm15MinIntervalDowns,
       g9983SvcPm15MinIntervalValid
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects supporting OPTIONAL historical
       Performance Monitoring information for G.Bond/TDIM ports, during
       previous 15-minute intervals ."
     ::= { g9983Groups 6 }

   g9983Perf1DayGroup OBJECT-GROUP
     OBJECTS {
       g9983PortPm1DayIntervalMoniTime,



Beili                  Expires September 13, 2012              [Page 48]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


       g9983PortPm1DayIntervalCrc4s,
       g9983PortPm1DayIntervalCrc6s,
       g9983PortPm1DayIntervalCrc8s,
       g9983PortPm1DayIntervalValid,
       g9983SvcPm1DayIntervalMoniTime,
       g9983SvcPm1DayIntervalDowns,
       g9983SvcPm1DayIntervalValid
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects supporting OPTIONAL historical
       Performance Monitoring information for G.Bond/TDIM ports, during
       previous 1-day intervals ."
     ::= { g9983Groups 7 }

  -- Compliance Statements

   g9983Compliance MODULE-COMPLIANCE
     STATUS      current
     DESCRIPTION
       "The compliance statement for G.Bond/TDIM interfaces.
       Compliance with the following external compliance statements
       is REQUIRED:

       MIB Module             Compliance Statement
       ----------             --------------------
       IF-MIB                 ifCompliance3
       GBOND-MIB              gBondCompliance"

     MODULE  -- this module
       MANDATORY-GROUPS {
         g9983BasicGroup,
         g9983AlarmConfGroup,
         g9983NotificationGroup
       }

       GROUP       g9983FecGroup
       DESCRIPTION
         "Support for this group is only required for implementations
         supporting G.Bond/TDIM FEC and Interleaver function."

       GROUP       g9983PerfCurrGroup
       DESCRIPTION
         "Support for this group is only required for implementations
         supporting Performance Monitoring."

       GROUP       g9983Perf15MinGroup
       DESCRIPTION



Beili                  Expires September 13, 2012              [Page 49]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


         "Support for this group is only required for implementations
         supporting historical Performance Monitoring."

       GROUP       g9983Perf1DayGroup
       DESCRIPTION
         "Support for this group is only required for implementations
         supporting historical Performance Monitoring."

     ::= { g9983Compliances 1 }
END

7.  Security Considerations

   There is a number of managed objects defined in this MIB module with
   a MAX-ACCESS clause of read-write and/or read-create.  Such objects
   may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.  These are the tables and objects and their
   sensitivity/vulnerability:

   o  Changing of g9983PortConfAdminServices object may lead to a
      potential service disruption, by changing a particular service'
      position (therefore changing its drop priority) or even removing
      the service from the link altogether.

   o  Changing of g9983SvcTable configuration parameters (e.g.
      g9983SvcType or g9983SvcSize) may lead to a potential service
      impairment, for example a TDM service would be dropped if there is
      not enough actual bandwidth on the bonded link to support this
      service.

   o  Changing of g9983PortConfTable configuration parameters (e.g.
      g9983PortConfFecAdminState) may lead to anything from link quality
      and rate degradation to a complete link initialization failure.

   Some of the readable objects in this MIB module (i.e., those with
   MAX-ACCESS other than not-accessible) may be considered sensitive or
   vulnerable in some network environments since, collectively, they
   provide information about the performance of network interfaces and
   can reveal some aspects of their configuration.

   In particular, since a bonded xDSL port can be comprised of multiple
   Unshielded Twisted Pair (UTP) voice grade copper, located in the same
   bundle with other pairs belonging to another operator/customer, it is
   theoretically possible to eavesdrop to a G.Bond transmission, simply
   by "listening" to a cross-talk from the bonded pairs, especially if
   the operating parameters of the G.Bond link in question are known.



Beili                  Expires September 13, 2012              [Page 50]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


   It is thus important to control even GET and/or NOTIFY access to
   these objects and possibly even encrypt the values of these objects
   when sending them over the network via SNMP.  These are the tables
   and objects and their sensitivity/vulnerability:

   o  g9983PortStatFecOperState in g9983PortStatTable indicate whether
      the FEC function is enabled, which may aid in deciphering of the
      G.Bond/TDIM transmissions.

   o  g9983OperSvcTable provide current operational service
      configuration, which may aid in deciphering of the G.Bond/TDIM
      transmissions.

   SNMP versions prior to SNMPv3 did not include adequate security.
   Even if the network itself is secure (for example by using IPSec),
   there is no control as to who on the secure network is allowed to
   access and GET/SET (read/change/create/delete) the objects in this
   MIB module.

   Implementations MUST provide the security features described by the
   SNMPv3 framework (see [RFC3410]), including full support for
   authentication and privacy via the User-based Security Model (USM)
   [RFC3414] with the AES cipher algorithm [RFC3826].  Implementations
   MAY also provide support for the Transport Security Model (TSM)
   [RFC5591] in combination with a secure transport such as SSH
   [RFC5592] or TLS/DTLS [RFC6353].

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED.  Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module is properly configured to give access to
   the objects only to those principals (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.

8.  IANA Considerations

   An object identifier for g9983MIB MODULE-IDENTITY SHALL be allocated
   by IANA [1] in the MIB-2 transmission sub-tree, before this document
   is published as an RFC.

9.  Acknowledgments

   This document was produced by the [ADSLMIB] working group.

   Special thanks to Dan Romascanu for his meticulous review of this
   text.




Beili                  Expires September 13, 2012              [Page 51]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


10.  References

10.1.  Normative References

   [G.998.3]                     ITU-T, "Multi-pair bonding using time-
                                 division inverse multiplexing", ITU-T
                                 Recommendation G.998.3, January 2005, <
                                 http://www.itu.int/rec/T-REC-
                                 G.998.3/en>.

   [I-D.ietf-adslmib-gbond-mib]  Beili, E. and M. Morgenstern, "xDSL
                                 multi-pair bonding (G.Bond) MIB",
                                 draft-ietf-adslmib-gbond-mib-10 (work
                                 in progress), March 2011.

   [RFC2119]                     Bradner, S., "Key words for use in RFCs
                                 to Indicate Requirement Levels",
                                 BCP 14, RFC 2119, March 1997.

   [RFC2578]                     McCloghrie, K., Ed., Perkins, D., Ed.,
                                 and J. Schoenwaelder, Ed., "Structure
                                 of Management Information Version 2
                                 (SMIv2)", STD 58, RFC 2578, April 1999.

   [RFC2579]                     McCloghrie, K., Ed., Perkins, D., Ed.,
                                 and J. Schoenwaelder, Ed., "Textual
                                 Conventions for SMIv2", STD 58,
                                 RFC 2579, April 1999.

   [RFC2580]                     McCloghrie, K., Perkins, D., and J.
                                 Schoenwaelder, "Conformance Statements
                                 for SMIv2", STD 58, RFC 2580,
                                 April 1999.

   [RFC2863]                     McCloghrie, K. and F. Kastenholz, "The
                                 Interfaces Group MIB", RFC 2863,
                                 June 2000.

   [RFC3414]                     Blumenthal, U. and B. Wijnen, "User-
                                 based Security Model (USM) for version
                                 3 of the Simple Network Management
                                 Protocol (SNMPv3)", STD 62, RFC 3414,
                                 December 2002.

   [RFC3705]                     Ray, B. and R. Abbi, "High Capacity
                                 Textual Conventions for MIB Modules
                                 Using Performance History Based on 15
                                 Minute Intervals", RFC 3705,



Beili                  Expires September 13, 2012              [Page 52]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


                                 February 2004.

   [RFC3826]                     Blumenthal, U., Maino, F., and K.
                                 McCloghrie, "The Advanced Encryption
                                 Standard (AES) Cipher Algorithm in the
                                 SNMP User-based Security Model",
                                 RFC 3826, June 2004.

   [RFC5591]                     Harrington, D. and W. Hardaker,
                                 "Transport Security Model for the
                                 Simple Network Management Protocol
                                 (SNMP)", RFC 5591, June 2009.

   [RFC5592]                     Harrington, D., Salowey, J., and W.
                                 Hardaker, "Secure Shell Transport Model
                                 for the Simple Network Management
                                 Protocol (SNMP)", RFC 5592, June 2009.

   [RFC6353]                     Hardaker, W., "Transport Layer Security
                                 (TLS) Transport Model for the Simple
                                 Network Management Protocol (SNMP)",
                                 RFC 6353, July 2011.

   [TR-159]                      Beili, E. and M. Morgenstern,
                                 "Management Framework for xDSL
                                 Bonding", Broadband Forum technical
                                 report TR-159, December 2008.

10.2.  Informative References

   [ADSLMIB]                     IETF, "ADSL MIB (adslmib) Charter", <ht
                                 tp://www.ietf.org/html.charters/
                                 adslmib-charter.html>.

   [G.704]                       ITU-T, "Synchronous frame structures
                                 used at 1544, 6312, 2048, 8448 and
                                 44736 Kbit/s hierarchical levels.",
                                 ITU-T Recommendation G.704,
                                 October 1998,
                                 <http://www.itu.int/rec/T-REC-
                                 G.704/en>.

   [RFC3410]                     Case, J., Mundy, R., Partain, D., and
                                 B. Stewart, "Introduction and
                                 Applicability Statements for Internet-
                                 Standard Management Framework",
                                 RFC 3410, December 2002.




Beili                  Expires September 13, 2012              [Page 53]

Internet-Draft               G.Bond/TDIM MIB                  March 2012


   [RFC3593]                     Tesink, K., "Textual Conventions for
                                 MIB Modules Using Performance History
                                 Based on 15 Minute Intervals",
                                 RFC 3593, September 2003.

   [RFC4181]                     Heard, C., "Guidelines for Authors and
                                 Reviewers of MIB Documents", BCP 111,
                                 RFC 4181, September 2005.

URIs

   [1]  <http://www.iana.org/>

Author's Address

   Edward Beili
   Actelis Networks
   25 Bazel St.
   Petach-Tikva  49103
   Israel

   Phone: +972-3-924-3491
   EMail: edward.beili@actelis.com




























Beili                  Expires September 13, 2012              [Page 54]


Html markup produced by rfcmarkup 1.109, available from https://tools.ietf.org/tools/rfcmarkup/