[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: (draft-kelly-capwap-threat-analysis) 00 01 02 03 04 RFC 5418

Network Working Group                                           S. Kelly
Internet-Draft                                            Aruba Networks
Intended status: Informational                                 T. Clancy
Expires: January 22, 2009                                            LTS
                                                           July 21, 2008


           CAPWAP Threat Analysis for IEEE 802.11 Deployments
                  draft-ietf-capwap-threat-analysis-02

Status of this Memo

   By submitting this Internet-Draft, each author represents that any
   applicable patent or other IPR claims of which he or she is aware
   have been or will be disclosed, and any of which he or she becomes
   aware will be disclosed, in accordance with Section 6 of BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

   This Internet-Draft will expire on January 22, 2009.

Abstract

   Early Wireless Local Area Network (WLAN) deployments feature a "fat"
   Access Point (AP) which serves as a standalone interface between the
   wired and wireless network segments.  However, this model raises
   scaling, mobility, and manageability issues, and the Control and
   Provisioning for Wireless Access Points (CAPWAP) protocol is meant to
   address these issues.  CAPWAP effectively splits the fat AP
   functionality into two network elements, and the communication
   channel between these components may traverse potentially hostile
   hops.  This document analyzes the security exposure resulting from
   the introduction of CAPWAP, and summarizes the associated security
   considerations for IEEE 802.11-based CAPWAP implementations and



Kelly & Clancy          Expires January 22, 2009                [Page 1]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   deployments.


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  4
     1.1.  Rationale for Limiting Analysis Scope to IEEE 802.11 . . .  5
   2.  Abbreviations and Definitions  . . . . . . . . . . . . . . . .  6
   3.  CAPWAP Security Goals for IEEE 802.11 Deployments  . . . . . .  7
   4.  Overview of IEEE 802.11 and AAA Security . . . . . . . . . . .  8
     4.1.  IEEE 802.11 Authentication and AAA . . . . . . . . . . . .  9
     4.2.  IEEE 802.11 Link Security  . . . . . . . . . . . . . . . . 10
     4.3.  AAA Security . . . . . . . . . . . . . . . . . . . . . . . 10
     4.4.  Cryptographic Bindings . . . . . . . . . . . . . . . . . . 11
   5.  Structure of the Analysis  . . . . . . . . . . . . . . . . . . 12
   6.  Representative CAPWAP Deployment Scenarios . . . . . . . . . . 13
     6.1.  Preliminary Definitions  . . . . . . . . . . . . . . . . . 13
       6.1.1.  Split MAC  . . . . . . . . . . . . . . . . . . . . . . 14
       6.1.2.  Local MAC  . . . . . . . . . . . . . . . . . . . . . . 14
       6.1.3.  Remote MAC . . . . . . . . . . . . . . . . . . . . . . 15
       6.1.4.  Data Tunneling . . . . . . . . . . . . . . . . . . . . 15
     6.2.  Example Scenarios  . . . . . . . . . . . . . . . . . . . . 15
       6.2.1.  Localized Modular Deployment . . . . . . . . . . . . . 15
       6.2.2.  Internet Hotspot or Temporary Network  . . . . . . . . 16
       6.2.3.  Distributed Deployments  . . . . . . . . . . . . . . . 17
   7.  General Adversary Capabilities . . . . . . . . . . . . . . . . 18
     7.1.  Passive vs Active Adversaries  . . . . . . . . . . . . . . 19
   8.  Vulnerabilities Introduced by CAPWAP . . . . . . . . . . . . . 20
     8.1.  The Session Establishment Phase  . . . . . . . . . . . . . 21
       8.1.1.  The Discovery Phase  . . . . . . . . . . . . . . . . . 21
       8.1.2.  Forming an Association (Joining) . . . . . . . . . . . 22
     8.2.  The Connected Phase  . . . . . . . . . . . . . . . . . . . 22
   9.  Adversary Goals in CAPWAP  . . . . . . . . . . . . . . . . . . 23
     9.1.  Eavesdrop on AC-WTP Traffic  . . . . . . . . . . . . . . . 23
     9.2.  WTP Impersonation and/or Rootkit Installation  . . . . . . 24
     9.3.  AC Impersonation . . . . . . . . . . . . . . . . . . . . . 24
     9.4.  Other Goals or Sub-Goals . . . . . . . . . . . . . . . . . 25
   10. Countermeasures and Their Effects  . . . . . . . . . . . . . . 26
     10.1. Communications Security Elements . . . . . . . . . . . . . 26
       10.1.1. Mutual Authentication  . . . . . . . . . . . . . . . . 26
       10.1.2. Data Origin Authentication . . . . . . . . . . . . . . 26
       10.1.3. Data Integrity Verification  . . . . . . . . . . . . . 27
       10.1.4. Antireplay . . . . . . . . . . . . . . . . . . . . . . 27
       10.1.5. Confidentiality  . . . . . . . . . . . . . . . . . . . 27
     10.2. Putting the Elements Together  . . . . . . . . . . . . . . 27
       10.2.1. Control Channel Security . . . . . . . . . . . . . . . 27
       10.2.2. Data Channel Security  . . . . . . . . . . . . . . . . 27
   11. Countermeasures Provided By DTLS . . . . . . . . . . . . . . . 28



Kelly & Clancy          Expires January 22, 2009                [Page 2]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   12. Issues Not Addressed By DTLS . . . . . . . . . . . . . . . . . 28
     12.1. DoS Attacks  . . . . . . . . . . . . . . . . . . . . . . . 28
     12.2. Passive Monitoring (Sniffing)  . . . . . . . . . . . . . . 29
     12.3. Traffic Analysis . . . . . . . . . . . . . . . . . . . . . 29
     12.4. Active MitM Interference . . . . . . . . . . . . . . . . . 29
     12.5. Other Active Attacks . . . . . . . . . . . . . . . . . . . 29
   13. Security Considerations  . . . . . . . . . . . . . . . . . . . 30
   14. IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 30
   15. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 30
   16. References . . . . . . . . . . . . . . . . . . . . . . . . . . 30
     16.1. Normative References . . . . . . . . . . . . . . . . . . . 30
     16.2. Informative References . . . . . . . . . . . . . . . . . . 31
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 31
   Intellectual Property and Copyright Statements . . . . . . . . . . 33





































Kelly & Clancy          Expires January 22, 2009                [Page 3]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


1.  Introduction

   Wireless Local Area Network (WLAN) deployments are increasingly
   common as the technology matures and wireless interface chips become
   standard equipment in laptops and various hand-held computing
   devices.  In the simplest deployments, WLAN access is entirely
   provided by a wireless Access Point (AP), which bridges the client
   system (station or "STA") and the Distribution System (DS) or wired
   network.

        +------+
        |client|         +--------+     |
        |(STA) |         | Access |     |    +------+
        +------+ ) ) ) ) | Point  |-----|   /optional\    +-------+
       /      /          +--------+     |--(    L3    )---|  AAA  |
      +------+                          |   \ cloud  /    +-------+
                                        |    +------+

                  Figure 1: IEEE 802.11 deployment using RSN

   In this architecture the AP serves as a gatekeeper, facilitating
   client access to the wired LAN.  Typically, the client must somehow
   authenticate prior to being granted access, and in enterprise
   deployments this is frequently accomplished using IEEE 802.1X
   [8021X].  Here, the client is called the "supplicant", the AP is the
   "authenticator", and either the AP or an external Authentication,
   Authorization, and Accounting (AAA) server fulfill the role of
   "authentication server", depending on the authentication mechanism
   used.

   From the perspective of the network administrator, the wired LAN to
   which the AP is attached is typically considered to be more trusted
   than the wireless LAN, either because there is some physical boundary
   around the wired segment (i.e. the building walls), or because it is
   otherwise secured somehow (perhaps cryptographically).  The AAA
   server may reside within this same physical administrative domain, or
   it may be remote.

   CAPWAP [I-D.ietf-capwap-protocol-specification] modifies this
   architecture by splitting the AP into two pieces, the Wireless
   Termination Point (WTP), and the Access Controller (AC), and creating
   a communications link between the two new components.  In this model,
   the WTP implements the WLAN edge functions with respect to the user
   (wireless transmit/receive), while the AC implements the wired-side
   edge functions.  For a complete description of CAPWAP architecture,
   see [RFC4118].





Kelly & Clancy          Expires January 22, 2009                [Page 4]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


     +------+    +==========================+
     |client|    |           +---+          |   |    +------+
     |(STA) |    | +-----+  /  L3 \  +----+ |   |   /optional\   +-----+
     +------+ ) )|)| WTP |-( cloud )-| AC |-|---|--(    L3    )--| AAA |
    /      /     | +-----+  \     /  +----+ |   |   \ cloud  /   +-----+
   +------+      |           +---+          |   |    +------+
                 +==========================+
                    AP equivalence boundary

                        figure 2

   For our purposes, it is useful to think of the entire CAPWAP system
   as a sort of "AP equivalent", and the figure above illustrates this
   concept.  With this model in mind, our ideal is to ensure that CAPWAP
   introduces no vulnerabilities which aren't present in the original
   fat AP scenario.  As we will see, this is not entirely possible, but
   from a security perspective we should nonetheless strive to achieve
   this equivalence as nearly as we can.

1.1.  Rationale for Limiting Analysis Scope to IEEE 802.11

   Although CAPWAP derives from protocols which were designed explicitly
   for management of IEEE 802.11 wireless LANs, it may also turn out to
   be useful for managing other types of network device deployments,
   wireless and otherwise.  This might lead one to conclude that a
   single security analysis, except for minor per-binding variations,
   might be sufficient.  However, based on a limited number of
   additional related scenarios that have been described as likely
   candidates for CAPWAP thus far, e.g., use with Radion Frequency
   Identification (RFID) sensors, this does not seem to be a simple,
   binary decision.

   Contrasting RFID and IEEE 802.11 deployment scenarios, IEEE 802.11
   users typically authenticate to some sort of back-end AAA server, and
   as a result of that exchange, derive cryptographic keys which are
   used by the STA and WTP to encrypt and authenticate over-air
   communications.  That is, the threat environment is such that the
   following typically holds:

   o  the user is not immediately trusted, and therefore must
      authenticate

   o  the WTP is not immediately trusted, and therefore must indirectly
      authenticate to the user via the AAA server

   o  the AAA server is not necessarily trusted, and therefore must
      authenticate




Kelly & Clancy          Expires January 22, 2009                [Page 5]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   o  the medium is not trusted, and therefore communications must be
      secured

   RFID tags, on the other hand, typically do not have the same
   authentication, confidentiality, and integrity requirements as the
   principals in a WLAN deployment, and are not, generally speaking,
   well suited to environments in which similar threats exist.  As a
   result of the combination of WLAN security requirements and the MAC-
   splitting behavior which epitomizes the IEEE 802.11 binding for
   CAPWAP, there are definite security-related considerations in the
   WLAN case which simply do not exist for an RFID-based adaptation of
   CAPWAP.

   Now, there certainly are similarities and overlapping security
   considerations which will apply to any CAPWAP deployment scenario.
   For example, authentication of the AC for purposes of WTP device
   management operations is probably always important.  Even so, the
   threats to RFID are different enough to suggest the need for a
   separate security analysis in that case.  For example, since RFID
   tags commonly deployed today implement no over-air authentication,
   integrity, or confidentiality mechanisms, the need for similar
   mechanisms between the WTP and AC for RFID tag data communications is
   not clearly indicated - that is, the threats are different.

   We have limited visibility into the varied ways in which CAPWAP might
   be adapted in the future, although we may observe that it seems to
   provide the basis for a generalized scalable provisioning protocol.
   Given our currently limited view of the technologies for which it
   might be used, it seems prudent to recognize that our current view is
   colored by the IEEE 802.11 roots of the protocol, and make that
   recognition explicit in our analysis.  If newly added bindings turn
   out to be substantially similar to IEEE 802.11, then the associated
   binding documents can simply reference this document in their
   security considerations, while calling out any substantive
   differences.  However, it does appear, based on our current limited
   visibility, that per-binding threat analyses will be required.


2.  Abbreviations and Definitions

   o    AAA - Authentication Authorization and Accounting

   o    AC - Access Controller

   o    AES-CCMP - Advanced Encryption Standard - Counter mode Cbc MAC
        Protocol





Kelly & Clancy          Expires January 22, 2009                [Page 6]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   o    AP - (wireless) Access Point

   o    CAPWAP - Control And Provisioning of Wireless Access Points

   o    Cert - X509v3 Certificate

   o    DIAMETER - proposed successor to RADIUS protocol (see below)

   o    DoS - Denial of Service (attack)

   o    DTLS - Datagram Transport Layer Security

   o    EAP - Extensible Authentication Protocol

   o    MitM - Man in the Middle

   o    PMK - Pairwise Master Key

   o    PSK - PreShared Key

   o    RADIUS - Remote Authentication Dial-In User Service

   o    STA - (wireless) STAtion

   o    TK - Transient Key

   o    TKIP - Temporal Key Integrity Protocol

   o    WEP - Wired Equivalent Privacy

   o    WLAN - Wireless Local Area Network

   o    WTP - Wireless Termination Point


3.  CAPWAP Security Goals for IEEE 802.11 Deployments

   When deployed for use with IEEE 802.11, CAPWAP should avoid
   introducing any system security degradation as compared to the fat AP
   scenario.  However, by splitting the AP functions between the WTP and
   AC, CAPWAP places potentially sensitive protocol interactions that
   were previously internal to the WTP onto the L3 network between the
   AC and WTP.  Therefore, the security properties of this new system
   are dependent on the security properties of the intervening network
   cloud, as well as on the details of the split.

   Since CAPWAP does not directly interact with over-air or AAA
   protocols, these are, for the most part, out of scope for this



Kelly & Clancy          Expires January 22, 2009                [Page 7]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   analysis.  That is, we do not analyze the basic AAA or IEEE 802.11
   security protocols directly here, as CAPWAP does not modify these
   protocols in any way, nor do they directly interact with CAPWAP.
   However, by splitting AP functionality, CAPWAP may expose security
   elements of these protocols that would not otherwise be exposed.  In
   such cases, CAPWAP should explicitly avoid degrading the security of
   these protocols in any way when compared to the fat AP scenario.


4.  Overview of IEEE 802.11 and AAA Security

   While this document is not directly concerned with IEEE 802.11 or AAA
   security, there are some subtle interactions introduced by CAPWAP,
   and there will be related terminology we must touch on in discussing
   these.  The following figure illustrates some of the complex
   relationships between the various protocols, and illustrates where
   CAPWAP sits:


                             +-----+  RADIUS/Diameter
                             | AAA |<==============\\
                             +-----+               ||
                                |                  ||
                    +-----------+------------+     ||
                    |                        |     ||
                 +-----+                  +----+   ||
                 | AC  |                  | AC |<==//
                 +-----+                  +----+
              +---|  |---+             +---|  |---+
              |          |             |          |
              |          |             |  CAPWAP  |
           +-----+    +-----+       +-----+    +-----+
           | WTP |    | WTP |       | WTP |    | WTP |
           +-----+    +-----+       +-----+    +-----+
           ^                       ^^^
          ^^                      ^^^  802.11i,
          ^^                      ^^  802.1X, WPA,
      +-----+              +-----+     WEP
      | STA |              | STA |
      +-----+              +-----+
     /     /              /     /
    +-----+              +-----+


   CAPWAP is being inserted between the 802.ll link security mechanism
   and the authentication server communication, so to provide supporting
   context, we give a very brief overview of IEEE 802.11 and AAA
   security below.  It is very important to note that we only cover



Kelly & Clancy          Expires January 22, 2009                [Page 8]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   those topics which are relevant to our discussion, so what follows is
   not by any means exhaustive.  For more detailed coverage of IEEE
   802.11-related security, topics see e.g. [80211SEC]

4.1.  IEEE 802.11 Authentication and AAA

   IEEE 802.11 provides for multiple methods of authentication prior to
   granting access to the network.  In the simplest case, open
   authentication is used, and this is equivalent to no authentication.
   However, if IEEE 802.11 link security is to be provided, then some
   sort of authentication is required in order to bootstrap the trust
   relationship which underlies the associated key establishment
   process.

   This authentication can be implemented through use of a shared
   secret.  In such cases the authentication may be implicitly tied to
   the link security mechanism, (e.g. when Wired Equivalent Privacy
   (WEP) is used with open authentication), or it may be explicit, e.g.
   when Wi-fi Protected Access is used with a Pre-Shared Key (WPA-PSK).

   In other cases, authentication requires an explicit cryptographic
   exchange, and this operation bootstraps link security.  In most such
   cases, IEEE 802.1X is used in conjunction with the Extensible
   Authentication Protocol [RFC3748] to authenticate either the client
   or both the client and the authentication server.  This exchange
   produces cryptographic keying material for use with IEEE 802.11
   security mechnisms.

   The resulting trust relationships are complex, as can be seen from
   the following (simplified) figure:

             /--------------------------------------------\
             |                       TK (6)               | EAP Credentials,
             V                  /--------------\          | PMK (3)
          +------+              |  PSK/Cert(1) |          |
          |client|              V              |          V
          |(STA) |         +--------+     |    v     |  +-----+
          +------+ ) ) ) ) |  WTP   |-----|  +----+  |--| AAA |
         /      /          +--------+     |--| AC |--|  +-----+
        +------+              ^           |  +----+  |      ^
          ^  ^                |               ^  ^ (2,4)    |
          |  |    PTK (7)     |               |  \----------/
          |  \----------------/               |   Radius PSK,
          \-----------------------------------/       PMK
                  4-Way Handshake (w/PMK) (5)

                          figure 3




Kelly & Clancy          Expires January 22, 2009                [Page 9]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   1.  WTP and AC establish secure link

   2.  AC establishes secure link with AAA server

   3.  STA and AAA server conduct EAP, produce PMK

   4.  AAA server pushes PMK to AC

   5.  AC and STA conduct 4-way handshake (producing TK, among other
       keys)

   6.  AC pushes TK to WTP (if decentralized encryption is used)

   7.  WTP/STA use TK for IEEE 802.11 link security

4.2.  IEEE 802.11 Link Security

   The current CAPWAP binding for IEEE 802.11 only supports the use of
   IEEE 802.11i security on the wireless link.  However, IEEE 802.11i
   does not prohibit the use of WEP for link security.

   If WEP is used with CAPWAP, the CAPWAP system will inherit all the
   security problems associated with the use of WEP in any wireless
   network.  In particular, 40-bit keys can be subject to brute-force
   attacks, and statistical attacks can be used to crack session keys
   after enough packets have been collected [WEPSEC].

   Newer link security mechanisms described in IEEE 802.11i, including
   TKIP and AES-CCMP, significantly improve the security of wireless
   networks.  It is strongly RECOMMENDED that CAPWAP only be used with
   these newer techniques.

   The only slight insecurity introduced by CAPWAP when using it with
   IEEE 802.11i is the handling of the KeyRSC counter.  When performing
   decentralized encryption, this value is maintained by the WTP, but
   needed by the AC to perform the four-way handshake.  The value used
   during the handshake initializes the counter on the client.  In
   CAPWAP, this value is initialized to zero, allowing the possibility
   for replay attacks of broadcast traffic in the window between initial
   authentication and the client receiving the first valid broadcast
   packet from the WTP.  This slight window of attack has been
   documented in the CAPWAP bindings document.

4.3.  AAA Security

   CAPWAP has very little control over how AAA security is deployed, as
   it's not directly bound to AAA as it is to IEEE 802.11.  As a result,
   CAPWAP can only provide guidance on how to best secure the AAA



Kelly & Clancy          Expires January 22, 2009               [Page 10]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   portions of a CAPWAP-enabled wireless network.

   The AAA protocol is a term that refers to use of either RADIUS
   [RFC3579] or Diameter [RFC4072] to transport EAP communications
   between the authenticator and the AAA server.  Here the authenticator
   is the AC, thus the AAA protocol secures the link between the AC and
   AAA server.  Use of non-unique or low-entropy long-term credentials
   to secure the AC-AAA link can severely impact the overall security of
   a CAPWAP deployment, and consequently is NOT RECOMMENDED.  Each AC
   should have a mutually-authenticated link that provides robust data
   confidentiality and integrity.

   Since CAPWAP does not directly interact with AAA, it does not affect
   the overall security of a AAA network.  In fact, by decreasing the
   number of devices that communicate with the AAA server, we can
   actually decrease its exposure and risk of attack.

4.4.  Cryptographic Bindings

   One key shortcoming of both the EAP and AAA models is that they are
   inherently two-party models.  In CAPWAP deployments, we rely on a
   variety of security associations when an IEEE 802.11 WLAN client
   session is established.  These include:

   o  WTP-AC (CAPWAP Authentication)

   o  AC-AAA (AAA Authentication)

   o  STA-AAA (EAP Method Execution)

   o  STA-AC (AAA pushes keys to AC)

   o  STA-WTP (AC pushes keys to WTP)

   Each of these security associations involve a pairwise trust
   relationship, and none result from a multi-party key agreement
   protocol such as Kerberos.  In particular, just because a STA trusts
   a AAA server who trusts an AC who trusts a WTP doesn't necessarily
   mean that the STA should trust the WTP.  In particular, the WTP may
   be compromised and using his credentials to maintain a trust
   relationship with an AC, while advertising false information about
   the network to a STA.

   Protection against attacks like these can be very difficult, while
   maintaining scalable trust relationships with other entities in the
   network.  Since multiple protocols are being used, multi-party keying
   to derive end-to-end trust relationships is infeasible.




Kelly & Clancy          Expires January 22, 2009               [Page 11]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   Since CAPWAP is a collection of pairwise trust relationships, in
   order to claim CAPWAP is secure, we must believe in the transitivity
   of these trust relationships.  Its hierarchal nature mitigates the
   domino effect, but any compromised device in the hierarchy can affect
   those below it in the hierarchy.


5.  Structure of the Analysis

   In order to conduct a comprehensive threat analysis, there are some
   basic questions we must answer:

   o  Exactly what are we trying to protect?

   o  What are the risks?

      *  What are the capabilities of would-be attackers?

      *  What might be goals of would-be attackers?

      *  What are the vulnerabilities or conditions they might attempt
         to exploit?

      *  For various attackers, what is the likelihood of attempting to
         exploit a given vulnerability given the cost of the the exloit
         vs. the value of attack?

   o  What potential mitigation strategies are available to us?

   o  What kinds of trade-offs do these mitigation strategies offer, and
      do they introduce any new risks?

   This is a very simplistic overview of what we must accomplish below,
   but it should give some insight into the manner in which the
   discussion proceeds.

   As a preliminary, we describe some representative CAPWAP deployment
   scenarios.  This helps to frame subsequent discussion, so that we
   better understand what we are trying to protect.  Following this, we
   describe a threat model in terms of adversary capabilities,
   vulnerabilities introduced by the CAPWAP functionality split, and a
   representative sampling of adversary goals.  Note that we do not
   spend a lot of time speculating about specific attackers here, as
   this is a very general analysis, and there are many different
   circumstances under which a WLAN might be deployed.

   Following the development of the general threat model, we describe
   appropriate countermeasures, and discuss how these are implemented



Kelly & Clancy          Expires January 22, 2009               [Page 12]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   through various means within the CAPWAP protocol.  Finally, we
   discuss those issues which are not (or cannot be) completely
   addressed, and we give recommendations for mitigating the resulting
   exposure.


6.  Representative CAPWAP Deployment Scenarios

   In this section, we describe some representative CAPWAP deployment
   scenarios, and in particular, those scenarios which have been taken
   into consideration for the current CAPWAP protocol security design.
   For clarity, we first provide some preliminary definitions, along
   with descriptions of common deployment configurations which span
   multiple scenarios.  Following this is a sampling of individual
   deployment scenarios.

6.1.  Preliminary Definitions

   The IEEE 802.11 standard describes several frame types, and
   variations in WLAN architectures dictate where these frame types
   originate and/or terminate (i.e. at the WTP or AC).  There are three
   basic IEEE 802.11 frame types currently defined:

   o  Control - in general, these are for managing the transmission
      medium (i.e. the airwaves).  Examples include RTS, CTS, ACK, PS-
      POLL, CF-POLL, CF-END, and CF-ACK

   o  Management - in general, these are for managing access to the
      logical network, as opposed to the physical medium.  Example
      functions include association, disassociation, reassociation,
      deauthentication, beacons, and probes

   o  Data - transit data (network packets)

   There are a number of other services provided by the WLAN
   infrastructure, including these:

   o  Packet distribution

   o  Synchronization

   o  Retransmissions

   o  Transmission Rate Adaptation

   o  Privacy/Confidentiality/Integrity (e.g.  IEEE 802.11i)

   The manner in which these (and other) services are divided among the



Kelly & Clancy          Expires January 22, 2009               [Page 13]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   AC and WTP is collectively referred to in terms of "MAC-splitting"
   characteristics.  For convenience, we briefly describe various forms
   of MAC-splitting below.  For further detail, see
   [I-D.ietf-capwap-protocol-specification] and
   [I-D.ietf-capwap-protocol-binding-ieee80211]

6.1.1.  Split MAC

   Split-MAC scenarios are characterized by the fact that some IEEE
   802.11 MAC messages are processed by the WTP, while some are
   processed by the AC.  For example, a split MAC implementation might
   divide IEEE 802.11 frame processing as follows:

   WTP

      *  Beacons

      *  Probes

      *  RTS, CTS, ACK, PS-POLL, CF-POLL,CF-END, CF-ACK

   AC

      *  Association/Reassociation/Disassociation

      *  Authentication/Deauthentication

      *  Key Management

      *  IEEE 802.11 Link Security (WEP, TKIP, IEEE 802.11i)

   The split MAC model is not confined to any one particular deployment
   scenario, as we'll see below, and vendors have considerable leeway in
   choosing how to distribute the IEEE 802.11 functionality.

6.1.2.  Local MAC

   Local-MAC scenarios are characterized by the fact that all IEEE
   802.11 MAC messages are processed by the WTP.  Copies of some may be
   forwarded to the AC as a matter of convenience (i.e. when the AC
   needs to record some info from the frame, for example when providing
   accounting services), but the primary function of CAPWAP in local MAC
   scenarios is to provide centralized control and management for the
   WTPs, and STA packets are generally bridged locally.







Kelly & Clancy          Expires January 22, 2009               [Page 14]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


6.1.3.  Remote MAC

   Remote MAC scenarios are characterized by the fact that all IEEE
   802.11 MAC messages are forwarded to the AC - the WTP does not
   process any of these locally.  This model supports very light-weight
   WTP's which need be little more than smart antennas.

6.1.4.  Data Tunneling

   Regardless of the approach to MAC-splitting, there is also the matter
   of where user data packets are translated between wired and wireless
   frame formats, i.e. where the bridging function occurs.  In some
   cases, user data frames are tunneled back to the AC, and in others,
   they are locally bridged by the WTP.  While one might expect remote
   MAC implementations to always tunnel data packets back to the AC, for
   local and split MAC modes the decision is not so clear.  Also, it's
   important to note that there are no rules or standards in place which
   rigidly define these terms and associated handling.  Data tunneling
   is further discussed for each scenario below.

6.2.  Example Scenarios

   In this section we describe a number of example deployment scenarios.
   This is not meant to be an exhaustive enumeration; rather, it is
   intended to give a general sense of how WLANs currently are or may be
   deployed.  This will provide important context when we discuss
   adversaries and threats in subsequent sections below.

6.2.1.  Localized Modular Deployment

   The localized modular model describes a WLAN which is deployed within
   a single domain of control, typically within either a single building
   or some otherwise physically contained area.  This would be typical
   of a small to medium-sized organization.  In general, the LAN enjoys
   some sort of physical security (e.g. it's within the confines of a
   building for which access is somehow limited), although the actual
   level of physical security is often far less than is assumed.

   In such deployments, the WLAN is typically an extension of a wired
   LAN.  However, its interface to the wired LAN can vary.  For example,
   the interconnection between the WTPs and ACs can have its own wiring,
   and its only connection to the LAN is via the AC's Distribution
   System (DS) port(s).  In such cases, the WLAN frequently occupies its
   own distinct addressing partition(s) in order to facilitate routing,
   and the AC often acts as a forwarding element.

   In other cases, the WTPs may be mingled with the existing LAN
   elements, perhaps sharing address space, or perhaps somehow logically



Kelly & Clancy          Expires January 22, 2009               [Page 15]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   isolated from other wired elements (e.g. by VLAN).  Under these
   circumstances, it is possible that traffic destined to/from the WLAN
   is mixed with traffic to/from the LAN.

   Localized deployments such as these could potentially choose any one
   of the MAC-splitting scenarios, depending on the size of the
   deployment, mobility requirements, and other considerations.  In many
   cases, any one of the various MAC-splitting approaches would be
   sufficient.  This implies that user data may be bridged by either the
   WTP or the AC.

6.2.2.  Internet Hotspot or Temporary Network

   The Internet hotspot scenario is representative of a more general
   deployment model one might find at cafes, hotels, or airports.  It is
   also quite similar to temporary WLANs which are created for
   conferences, conventions, and the like.  Some common characteristics
   of these networks include the following:

   o  Primary function is to provide Internet access

   o  Authentication may be very weak

   o  There frequently is no IEEE 802.11 link security

   Sometimes, the local-MAC model is used.  In such cases the AC may be
   "in the cloud" (out on the Internet somewhere), and user data traffic
   will typically be locally bridged, rather than tunneled back to the
   AC.  Some IEEE 802.11 management traffic may be tunneled back to the
   AC, but frequently the authentication consists in simply knowing the
   SSID and perhaps a shared key for use with WEP or WPA-PSK.

   In other cases, a split-MAC model may be used.  This is more common
   in airport and hotel scenarios, where users may have an account which
   requires verification with some back-end infrastructure prior to
   access.  In these cases, IEEE 802.11 management frames are tunneled
   back to the AC (e.g. user authentication), and stronger IEEE 802.11
   link security may be provided (e.g.  WPA), but user data is still
   typically locally bridged, as the primary goal is to provide Internet
   access.

   A third variation on this scenario entails tunneling user data
   through a local AC in order to apply centralized policy.  For
   example, in a hotel or airport scenarios, there is no reason to
   provide direct access between WLAN users (who typically are within a
   private address space), and in fact, allowing such access might
   invite various sorts of malicious behavior.  In such cases, tunneling
   all user data back to the (local) AC provides a security choke point



Kelly & Clancy          Expires January 22, 2009               [Page 16]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   at which policy may be applied to the traffic.

6.2.3.  Distributed Deployments

   The distributed deployment model describes a more complex WLAN
   topology which features network segments that are typically somehow
   spatially separated, although not necessarily so.  These segments
   might be connected in a physically secure manner, or (if they are
   widely separated) they might be connected across potentially hostile
   hops.  Below we discuss several subgroups of this model.

6.2.3.1.  Large Physically-Contained Organization

   One distributed deployment example involves a single large
   organization which is physically contained, typically within one
   large building.  The network might feature logically distinct (e.g.
   per-department or per-floor) network segments, and in some cases,
   there might be firewalls between the segments for access control.  In
   such deployments, the AC is typically in a centralized datacenter,
   but there might also be a hierarchy of ACs, with a master in the
   datacenter, and subordinate ACs distributed among the network
   segments.  Such deployments typically assume some level of physical
   security for the network infrastructure.

6.2.3.2.  Campus Deployments

   Some large organizations have networks which span multiple buildings.
   The interconnections between these buildings might be wired (e.g.
   underground cables), or might be wireless (e.g. a point to point MAN
   link).  The interconnections may be secured, but sometimes they are
   not.  The organization may be providing outdoor wireless access to
   users, in which case some WTPs will typically be located outdoors,
   and these may or may not be within physically secure space.  For
   example, college campuses frequently provide outdoor wireless access,
   and the associated WTPs may simply be mounted on a light post.

   For such deployments, ACs may be centrally located in a datacenter,
   or they may be distributed.  User data traffic may be locally
   bridged, but more frequently it is tunneled back to AC, as this
   facilitates mobility and centralized policy enforcement.

6.2.3.3.  Branch Offices

   A common deployment model entails an enterprise consisting of a
   headquarters and one or more branch offices, with the branches
   connected to the central HQ.  In some cases, the site-to-site
   connection is via a private WAN link, and in others it is across the
   Internet.  For connections crossing potentially hostile hops (e.g.



Kelly & Clancy          Expires January 22, 2009               [Page 17]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   the Internet), some sort of VPN is typically employed as a protective
   measure.

   In some simple branch office scenarios, there are only WTP's at the
   remote site, and these are managed by a controller residing at the
   central site.  In other cases, a branch site may have its own
   subordinate controller, with the master controller again residing at
   the central site.  In the first case, local bridging is often the
   best choice for user data, due to latency and link capacity issues.
   In the second case, traffic may be locally bridged by the WTPs, or it
   may be forwarded to the local subordinate controller for centralized
   policy enforcement.  The choice depends on many factors, including
   local topology and security policy.

6.2.3.4.  Telecommuter or Remote Office

   It is becoming increasingly common to send WTPs home with employees
   for use as a telecommuting solution.  While there are not yet any
   standards or hard rules for how these work, a fairly typical
   configuration provides split MAC with all user data tunneled back to
   the controller in the organization's datacenter so that the WTP is
   essentially providing wireless VPN services.  These devices may in
   some cases provide their own channel security (e.g.  IPsec), but
   alternative approaches are possible.  For example, there may be a
   standalone VPN gateway between the WTP and the Internet which
   forwards all organization-bound traffic to the VPN gateway.

   Similarly, it is becoming increasingly common for travelers to plug a
   WTP into a hotel broadband connection.  While in many cases, these
   WTPs are standalone fat AP's, in some cases they are configured to
   create a secure connection to a centralized controller back at
   headquarters, essentially forming a VPN connection.  In such
   scenarios, a split-MAC approach is typical, but split-tunneling may
   also be suppported (i.e. only data traffic destined for the
   headquarters is tunneled back to the controller, with Internet-bound
   traffic locally bridged).


7.  General Adversary Capabilities

   This section describes general capabilities we might expect an
   adversary to have in various CAPWAP scenarios.  Obviously, it is
   possible to limit what an adversary can do through various deployment
   restrictions (e.g. provide strict physical security for the AC-WTP
   link), but such restrictions are simply not always feasible.  For
   example, it is not possible to provide strict physical security for
   various aspects of the telecommuter scenario.  Thus, we must consider
   what capabilities an adversary might have in the worst case, and plan



Kelly & Clancy          Expires January 22, 2009               [Page 18]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   accordingly.

7.1.  Passive vs Active Adversaries

   One way to classify adversaries is in terms of their ability to
   interact with AC/WTP communications.  For example, a passive
   adversary is one who can observe and perhaps record traffic, but
   cannot interact with it.  They can "see" the traffic as it goes by,
   but they cannot interfere in any way, and they cannot inject traffic
   of their own.  Note that such an adversary does not necessarily see
   all traffic - they may miss portions of a communication e.g. because
   some packets traverse a different path, or because the network is so
   busy that the adversary can't keep up (and drops packets as a
   result).

   An active adversary, on the other hand, can directly interact with
   the traffic in realtime.  There are two modes in which an active
   adversary might operate:

   Pass-by (or sniffer)

      *  Can observe/record traffic

      *  Can inject packets

      *  Can replay packets

      *  Can reflect packets (i.e. send duplicate packets to a different
         destination, including the to the packet source)

      *  Can cause redirection (e.g. via ARP/DNS poisoning)

   Inline (Man in the Middle, or MitM)

      *  Can observe/record traffic

      *  Can inject packets

      *  Can replay packets

      *  Can reflect packets (with or without duplication)

      *  Can delete packets

      *  Can modify packets

      *  Can delay packets




Kelly & Clancy          Expires January 22, 2009               [Page 19]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   A passive adversary could be located anywere along the path between
   the AC and WTP, and is characterized by the fact that it only
   listens:

        +------+
        |client|         +--------+     |
        |(STA) |         |   WTP  |     |     +------+
        +------+ ) ) ) ) |        |-----|    /        \    +------+
       /      /          +--------+     |-x-( optional )---|  AC  |
      +------+                          | |  \ cloud  /    +------+
                                        | |   +------+
                                          |
                                          |  +-----------+
                                          +--|  pass-by  |
                                             |  listener |
                                             +-----------+

   An active adversary may attach in the same manner as the passive
   adversary (in which case it is in pass-by mode), or it may be lodged
   directly in the path between the AC and WTP (inline mode):

        +------+
        |client|       +--------+   |
        |(STA) |       |   WTP  |   | +------+    +------+
        +------+ ) ) ) |        |---| |active|   /        \    +------+
       /      /        +--------+   |-| MitM |--( optional )---|  AC  |
      +------+                      | +------+   \ cloud  /    +------+
                                    |             +------+


   If it is not inline, it can only observe and create traffic; if it is
   inline, it can do whatever it wishes with the traffic it sees.

   It is important to recognize that becoming a MitM does not
   necessarily require physical insertion directly into the transmission
   path.  Alternatively, the adversary can cause traffic to be diverted
   to the MitM system, e.g. via ARP or DNS poisoning.  Hence, launching
   a MitM attack is not so difficult as it might first appear.


8.  Vulnerabilities Introduced by CAPWAP

   In this section we discuss vulnerabilities which arise as a result of
   splitting the AP function across potentially hostile hops.  We
   primarily consider network-based vulnerabilities, and while in
   particular we do not address how an adversary might affect a physical
   compromise of the WTP and/or AC, we do consider the potential effects
   of such compromises with respect to CAPWAP and the operational



Kelly & Clancy          Expires January 22, 2009               [Page 20]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   changes it introduces when compared to standalone AP deployments.

   Functionally, we are interested in two general "states of being" with
   respect to AC-WTP communications: the session establishment phase or
   state, and the "connected" (or session established) state.  We
   discuss each of these further below.  Also, it is important to note
   that we first describe vulnerabilites assuming that the CAPWAP
   communications lack security of any kind.  Later, we will evaluate
   the protocol given the security mechanisms currently planned for
   CAPWAP.

8.1.  The Session Establishment Phase

   The session establishment phase consists of two subordinate phases:
   discovery, and association or joining.  These are treated
   individually in the following sections.

8.1.1.  The Discovery Phase

   Discovery consists of an information exchange between the AC and WTP.
   There are several potential areas of exposure:

   Information Leakage:  During discovery, information about the WTP and
      AC hardware and software are exchanged, as well as information
      about the AC's current operational state.  This could provide an
      adversary with valuable insights.

   DoS Potential:  During Discovery, there are several opportunities for
      Denial of Service (DoS), beyond those inherently available to an
      inline adversary.  For example, an adversary might respond to a
      WTP more quickly than a valid AC, causing the WTP to attempt to
      join with a non-existent AC, or one which is currently at maximum
      load.

   Redirection Potential:  There are multiple ways in which an adversary
      might redirect a WTP during discovery.  For example, the adversary
      might pretend to be a valid AC, and entice the WTP to connect to
      it.  Or, the adversary might instead cause the WTP to associate
      with the AC of the adversary's choosing, by posing as a DNS or
      DHCP server, injecting a spoofed discovery response, or by
      modifying valid AC responses.

   Misdirection:  An adversary might mislead either the WTP or AC by
      modifying the discovery request or response in flight.  In this
      way, the AC and/or WTP will have a false view of the other's
      capabilities, and this might cause a change in the way they
      interact (e.g. they might not use important features not supported
      by earlier versions).



Kelly & Clancy          Expires January 22, 2009               [Page 21]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


8.1.2.  Forming an Association (Joining)

   The association phase begins once the WTP has determined with which
   AC it wishes to join.  There are several potential areas of exposure
   during this phase:

   Information Leakage:  During association, the adversary could glean
      useful information about hardware, software, current
      configuration, etc. that could be used in various ways.

   DoS Potential:  During formation of a WTP-AC association, there are
      several opportunities for Denial of Service (DoS), beyond those
      inherently available to an inline adversary.  For example, the
      adversary could flood the AC with connection setup requests.  Or,
      it could respond to the WTP with invalid connection setup
      responses, causing a connection reset.  An adversary with MitM
      capability could delete critical session establishment packets.

   Misdirection:  An adversary might mislead either the WTP or AC by
      modifying the association request(s) or response(s) in flight.  In
      this way, the AC and/or WTP will have an inaccurate view of the
      other's capabilities, and this might cause a change in the way
      they interact.

   Some of these types of exposure are extremely difficult to prevent.
   However, there are things we can do to mitigate the effects, as we
   will see below.

8.2.  The Connected Phase

   Once the WTP and AC have established an association, the adversary's
   attention will turn to the network connection.  If we assume a
   passive adversary, the primary concern for established connections is
   eavesdropping.  If we assume an active adversary, there are several
   other potential areas of exposure:

   Connection Hijacking:  An adversary may assume the identity of one
      end of the connection and take over the conversation.  There are
      numerous ways in which the true owner of the identity may be taken
      offline, including DoS or MitM attacks.

   Eavesdropping:  An adversary may glean useful information from
      knowledge of the contents of CAPWAP control and/or data traffic.

   Modification of User Data:  An adversary with MitM capabilities could
      modify, delete, or insert user data frames.





Kelly & Clancy          Expires January 22, 2009               [Page 22]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   Modification of Control/Monitoring Messages:  An adversary with MitM
      capability could modify control traffic such as statistics, status
      information, etc. to create a false impression at the recipient.

   Modification/Control of Configuration  An adversary with MitM
      capability could modify configuration messages to create
      unexpected conditions at the recipient.  Likewise, if a WTP is
      redirected during discovery (or joining) and connects to an
      adversary rather than an authorized AC, the adversary may exert
      complete control over the WTP's configuration, including
      potentially loading tainted WTP firmware.


9.  Adversary Goals in CAPWAP

   This section gives an sampling of potential adversary goals.  It is
   not exhaustive, and makes no judgement as to the relative likelihood
   or value of each individual goal.  Rather, it is meant to give some
   idea of what is possible.  It is important to remember that clever
   attacks often result when seemingly innocuous flaws or
   vulnerabilities are combined in some non-intuitive way.  Hence, we
   don't rule out some goal that, taken alone, might not seem to make
   sense from an adversarial perspective.

9.1.  Eavesdrop on AC-WTP Traffic

   There are numerous reasons why an adversary might want to eavesdrop
   on AC-WTP traffic.  For example, it allows for reconnaissance,
   providing answers to the following questions:

   o  Where are the ACs?

   o  Where are the WTPs?

   o  Who owns them?

   o  Who manufactured them?

   o  What version of firmware do they run?

   o  What cryptographic capabilities do they have?

   o  etc...

   Similarly, snooping on tunneled data traffic might potentially reveal
   a great deal about the network, including answers to the following:





Kelly & Clancy          Expires January 22, 2009               [Page 23]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   o  Who's using the WLAN?

   o  When, and for how long?

   o  What addresses are they using?

   o  What protocols are they using?

   o  What over-the-air security are they using?

   o  Who/what are they talking to?

   o  etc...

   Additionally, access to tunneled user data could allow the attacker
   to see confidential information being exchanged by applications (e.g.
   financial transactions).  An eavesdropper may gain access to valuable
   information that either provides the basis for another perhaps more
   sophisticated attack, or which has its own intrinsic value.

9.2.  WTP Impersonation and/or Rootkit Installation

   An adversary might want to impersonate or control an authorized WTP
   for many reasons, some of which we might realistically imagine today,
   and perhaps others about which we have no clue at this point.
   Examples we might reasonably imagine include the following:

   o  to facilitate MitM attacks against WLAN users

   o  to leak/inject or otherwise compromise WLAN data

   o  to give an inaccurate view of the state of the WLAN

   o  to gain access to a trusted channel to an AC, through which
      various protocol attacks might be launched (e.g. hijack client
      sessions from other WTPs)

   o  to facilitate denial of service attacks against WLAN users or the
      network

9.3.  AC Impersonation

   For reasons similar to the WTP impersonation discussed above, an
   adversary might want to impersonate an authorized AC for many
   reasons.  Examples we might reasonably imagine include the following:

   o  to facilitate DoS attack against WLAN




Kelly & Clancy          Expires January 22, 2009               [Page 24]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   o  to facilitate MitM attacks against WLAN users

   o  to intercept user mobility context from another AC (possibly
      including security-sensitive information such as cryptographic
      keys)

   o  to facilitate selective control of one or more WTPs

      *  modify WTP configuration

      *  load tainted firmware onto WTP

   o  to assist in controlling which AC associates with which WTP

   o  to facilitate IEEE 802.11 association of unauthorized WLAN user(s)

   o  to exploit inter-AC trust in order facilitate attacks on other ACs

   In general, AC impersonation opens the door to a large measure of
   control over the WLAN, and could be used as the foundation to many
   other attacks.

9.4.  Other Goals or Sub-Goals

   There are many less concrete goals an adversary might have which,
   taken alone, might not seem to have any purpose, but when combined
   with other goals/attacks, might have very definite and undesireable
   consquences.  Here are some examples:

   o  cause CAPWAP de-association of WTP/AC

   o  cause IEEE 802.11 deassociation of authorized user

   o  inject/modify/delete tunneled IEEE 802.11 user traffic

      *  to interact with a specific application

      *  to launch various attacks on WLAN user systems

      *  to launch protocol fuzzing or other attacks on the AC which
         bridges between IEEE 802.11 and 802.3 frame formats

   o  control DNS responses

   o  control DHCP/BOOTP responses

   Anticipating all of the things an adversary might want to do is a
   daunting task.  Part of the difficulty stems from the fact that we



Kelly & Clancy          Expires January 22, 2009               [Page 25]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   are analyzing CAPWAP in a very general sense, rather than in a
   specific deployment scenario with specific assets and very specific
   adversary goals.  However, we have no choice but to take this
   approach if we are to provide reasonably good security across the
   board.


10.  Countermeasures and Their Effects

   In the previous sections we described numerous vulnerabilities which
   result from splitting the AP function in two, and also discussed a
   number of adversary goals which could be realized by exploiting one
   or more of those vulnerabilities.  In this section, we describe
   countermeasures we can apply to mitigate the risks that come with the
   introduction of CAPWAP into WLAN deployment scenarios.

10.1.  Communications Security Elements

10.1.1.  Mutual Authentication

   Mutual authentication consists in each side proving its identity to
   the other.  There are numerous authentication protocols which
   accomplish this, typically using either a shared secret (e.g. a
   preshared key) or by relying on a trusted third party (e.g. with
   digital credentials such as X.509 certificates).

   Strong mutual authentication accomplishes the following:

   o  helps prevent AC/WTP impersonation

   o  helps prevent MitM attacks

   o  can be used to limit DoS attacks

10.1.2.  Data Origin Authentication

   Data origin authentication typically depends on first authenticating
   the party at the other end of the channel, and then binding the
   identity derived from that authentication process to the data origin
   authentication process.  Data origin authentication primarily
   prevents an attacker from injecting data into the communication
   channel and pretending it was originated by a valid endpoint.  This
   mitigates risk by preventing the following:

   o  packet injection

   o  connection hijacking




Kelly & Clancy          Expires January 22, 2009               [Page 26]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   o  modification of control and/or user data

   o  impersonation

10.1.3.  Data Integrity Verification

   Data integrity verification provides assurance that data has not been
   altered in transit, and is another link in the trust chain beginning
   from mutual authentication, extending to data origin authentication,
   and ending with integrity verification.  This prevents the adversary
   from undetectably modifying otherwise valid data while in transit.
   It effectively prevents reflection and modification, and in some
   cases may help to prevent re-ordering.

10.1.4.  Antireplay

   Antireplay is somewhat self-explanatory: it prevents replay of valid
   packets at a later time, or to a different recipient.  It may also
   prevent limited re-ordering of packets.  It is typically accomplished
   by assigning monotonically increasing sequence numbers to packets.

10.1.5.  Confidentiality

   Data confidentiality prevents eavesdropping by protecting data as it
   passes over the network.  This is typically accomplished using
   encryption.

10.2.  Putting the Elements Together

   Above we described various security elements and their properties.
   Below, we discuss combinations of these elements in terms of CAPWAP.

10.2.1.  Control Channel Security

   The CAPWAP control channel is used for forming an association between
   a WTP and AC, and subsequently it allows the AC to provision and
   monitor the WTP.  This channel is critical for the control,
   management, and monitoring of the WLAN, and thus requires all of the
   security elements described above.  With these elements in place, we
   can effectively create a secure channel which mitigates almost all of
   the vulnerabilities described above.

10.2.2.  Data Channel Security

   The CAPWAP data channel contains some IEEE 802.11 management traffic
   including association/disassociation, reassociation, and
   deathentication.  It also may contain potentially sensitive user
   data.  If we assume that threats to this channel exist (i.e. it



Kelly & Clancy          Expires January 22, 2009               [Page 27]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   traverses potentially hostile hops), then providing strong mutual
   authentication coupled with data origin/integrity verification would
   prevent an adversary from injecting and/or modifying transit data, or
   impersonating a valid AC or WTP.  Adding confidentiality would
   prevent eavesdropping.


11.  Countermeasures Provided By DTLS

   Datagram TLS (DTLS) is the currently proposed security solution for
   CAPWAP.  DTLS supports the following security functionality:

   o  Mutual Authentication (preshared secrets or X.509 Certificates)

   o  Data Origin Authentication

   o  Data Integrity Verification

   o  Antireplay

   o  Confidentiality (supports strong cryptographic algorithms)

   Using DTLS for both the control and data channels mitigates nearly
   all risks resulting from splitting the AP function in two.


12.  Issues Not Addressed By DTLS

   Unfortunately, DTLS is not a magic elixir that dispenses with all of
   our CAPWAP security concerns.  There are some things it just cannot
   prevent.  These are enumerated below.

12.1.  DoS Attacks

   Even with the security provided by DTLS, CAPWAP is still susceptible
   to various types of DoS attack:

   o  Session Initialization: an adversary could initiate thousands of
      DTLS handshakes simultaneously in order to exhaust memory
      resources on the AC; DTLS provides a mitigation tool via the
      HelloVerifyRequest, which ensures that the initiator can receive
      packets at the claimed source address prior to allocating
      resources.  However, this would not thwart a botnet-style attack.

   o  Cryptographic DoS: an adversary could flood either the AC or WTP
      with properly formed DTLS records containing garbage, causing the
      recipient to waste compute cycles decrypting and authenticating
      the traffic



Kelly & Clancy          Expires January 22, 2009               [Page 28]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   o  Session interference: a MitM could either drop important session
      establishment packets, or inject bogus connection resets during
      session establishment phase.  It could also interfere with other
      traffic in an established session.

   These attacks can be mitigated thorugh various mechanisms, but not
   entirely avoided.  For example, session initialization can be rate-
   limited, and in case of resource exhaustion, some number of
   incompletely initialized sessions could be discarded.  Also, such
   events should be strictly audited.

   Likewise, cryptographic DoS attacks are detectable if appropriate
   auditing and monitoring controls are implemented.  When detected,
   these events should (at minimum) trigger an alert.  Additional
   mitigation might be realized by randomly discarding packets.

   Session interference is probably the most difficult of DoS attacks.
   It is very difficult to detect in realtime, although it may be
   detected if exceeding a lost packet threshhold triggers an alert.
   However, this depends on the MitM not being in a position to delete
   the alert before it reaches it's appropriate destination.

12.2.  Passive Monitoring (Sniffing)

   CAPWAP protocol security cannot prevent (or detect) passive
   monitoring.  The best we can do is provide a confidentiality
   mechanism.

12.3.  Traffic Analysis

   DTLS provides no defense for traffic analysis.  If this is a concern,
   there are traffic generation and padding techniques designed to
   mitigate this threat, but none of these are currently specified for
   CAPWAP.

12.4.  Active MitM Interference

   This was discussed in more limited scope in the section above on DoS
   attacks.  An active MitM can delete or re-order packets in a manner
   which is very difficult to detect, and there is little the CAPWAP
   protocol can do in such cases.  If packet loss is reported upon
   exceeding some threshold, then perhaps detection might be possible,
   but this is not guaranteed.

12.5.  Other Active Attacks

   In addition to the issues raised above, there are other active
   attacks that can be mounted if the adversary has access to the wired



Kelly & Clancy          Expires January 22, 2009               [Page 29]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   medium.  For example, the adversary may be able to impersonate a DNS
   or DHCP server, or to poison either a DNS or ARP cache.  Such attacks
   are beyond the scope of CAPWAP, and point to an underlying LAN
   security problem.


13.  Security Considerations

   This document outlines a threat analysis for CAPWAP, and as such, no
   additional CAPWAP-related security considerations are described here.
   However, in some cases additional management channels (e.g., SNMP)
   may be introduced into CAPWAP deployments.  Whenever this occurs,
   related security considerations MUST be described in detail in those
   documents.


14.  IANA Considerations

   This document introduces no IANA considerations.


15.  Acknowledgements

   The authors gratefully acknowledge the reviews and helpful comments
   of Dan Romascanu, Joe Salowey, Sam Hartman, and Mahalingham Mani.


16.  References

16.1.  Normative References

   [80211I]   "IEEE Std 802.11i: WLAN Specification for Enhanced
              Security", April 2004.

   [80211SEC]
              Edney, J. and W. Arbaugh, "Real 802.11 Security - Wi-Fi
              protected Access and 802.11i", 2004, <http://
              www.aw-bc.com/catalog/academic/product/
              0,1144,0321136209,00.html>.

   [8021X]    "IEEE Std 802.1X-2004: Port-based Network Access Control",
              December 2004.

   [I-D.ietf-capwap-protocol-binding-ieee80211]
              Calhoun, P., "CAPWAP Protocol Binding for IEEE 802.11",
              draft-ietf-capwap-protocol-binding-ieee80211-07 (work in
              progress), July 2008.




Kelly & Clancy          Expires January 22, 2009               [Page 30]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   [I-D.ietf-capwap-protocol-specification]
              Calhoun, P., "CAPWAP Protocol Specification",
              draft-ietf-capwap-protocol-specification-11 (work in
              progress), July 2008.

   [RFC4118]  Yang, L., Zerfos, P., and E. Sadot, "Architecture Taxonomy
              for Control and Provisioning of Wireless Access Points
              (CAPWAP)", RFC 4118, June 2005.

16.2.  Informative References

   [RFC3579]  Aboba, B. and P. Calhoun, "RADIUS (Remote Authentication
              Dial In User Service) Support For Extensible
              Authentication Protocol (EAP)", RFC 3579, September 2003.

   [RFC3748]  Aboba, B., Blunk, L., Vollbrecht, J., Carlson, J., and H.
              Levkowetz, "Extensible Authentication Protocol (EAP)",
              RFC 3748, June 2004.

   [RFC4017]  Stanley, D., Walker, J., and B. Aboba, "Extensible
              Authentication Protocol (EAP) Method Requirements for
              Wireless LANs", RFC 4017, March 2005.

   [RFC4072]  Eronen, P., Hiller, T., and G. Zorn, "Diameter Extensible
              Authentication Protocol (EAP) Application", RFC 4072,
              August 2005.

   [WEPSEC]   Petroni, N. and W. Arbaugh, "The Dangers of Mitigating
              Security Design Flaws: A Wireless Case Study",
              January 2003.


Authors' Addresses

   Scott G. Kelly
   Aruba Networks
   1322 Crossman Ave
   Sunnyvale, CA  94089
   US

   Email: scott@hyperthought.com










Kelly & Clancy          Expires January 22, 2009               [Page 31]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


   T. Charles Clancy
   DoD Laboratory for Telecommunications Sciences
   8080 Greenmead Drive
   College Park, MD  20740
   US

   Email: clancy@LTSnet.net












































Kelly & Clancy          Expires January 22, 2009               [Page 32]

Internet-Draft        CAPWAP 802.11 Threat Analysis            July 2008


Full Copyright Statement

   Copyright (C) The IETF Trust (2008).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
   THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
   OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.


Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.











Kelly & Clancy          Expires January 22, 2009               [Page 33]


Html markup produced by rfcmarkup 1.107, available from http://tools.ietf.org/tools/rfcmarkup/