[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 04 05 06 07 08 09 10 RFC 4327

Network Working Group                                       Martin Dubuc
Internet Draft                                          Meriton Networks
Expires: November 2002
                                                     Sudheer Dharanikota
                                                          Nayna Networks

                                                        Thomas D. Nadeau
                                                           Cisco Systems

                                                        Jonathan P. Lang
                                                           Evan McGinnis
                                                        Calient Networks

                                                                May 2002


          Link Management Protocol Management Information Base


                    draft-ietf-ccamp-lmp-mib-02.txt


Status of this Memo

   This document is an Internet-Draft and is in full conformance with
   all provisions of Section 10 of RFC 2026.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups. Note that other
   groups may also distribute working documents as Internet- Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time. It is inappropriate to use Internet- Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

Table of Contents

1.   Abstract .....................................................    2
2.   Introduction .................................................    2
3.   Terminology ..................................................    3
4.   The SNMP Management Framework ................................    3



Dubuc et al.             Expires November 2002                  [Page 1]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


5.   Feature Checklist ............................................    4
6.   Outline ......................................................    5
6.1. Summary of LMP MIB ...........................................    5
7.   Brief Description of MIB Objects .............................    6
7.1. lmpNbrTable ..................................................    6
7.2. lmpControlChannelTable .......................................    6
7.3. lmpControlChannelPerfTable ...................................    6
7.4. lmpTeLinkTable ...............................................    7
7.5. lmpLinkVerificationTable .....................................    7
7.6. lmpTeLinkPerfTable ...........................................    7
7.7. lmpDataBearingLinkTable ......................................    7
7.8. lmpDataBearingLinkPerfTable ..................................    7
8.   Example of LMP Control Channel Interface Setup ...............    7
9.   Application of the Interfaces Group to LMP ...................   10
9.1. Support of the LMP Layer by ifTable ..........................   10
10.  Link Management Protocol MIB Definitions .....................   12
11.  Security Considerations ......................................   78
12.  Acknowledgments ..............................................   79
13.  References ...................................................   79
14.  Authors' Addresses ...........................................   82
15.  Full Copyright Statement .....................................   82


1.  Abstract

   This memo defines an experimental portion of the Management Informa-
   tion Base (MIB) for use with network management protocols in the
   Internet community. In particular, it describes managed objects for
   modeling the Link Management Protocol (LMP) [LMP].


2.  Introduction

   Current work is underway in the IETF to specify a suite of protocols
   to be used as a common control plane and a separate common measure-
   ment plane. The Link Management Protocol, which primary purpose is to
   manage traffic engineering (TE) links, is one of the key components
   of this standardization activity. Primary goals of LMP are the
   maintenance of the control channel connectivity, correlation of link
   properties, verification of data-bearing links and detection and iso-
   lation of link faults.

   We describe in this document a MIB that can be used to manage LMP
   implementations. This MIB covers both configuration and performance
   monitoring aspects of LMP.

   Comments should be made directly to the ccamp mailing list at
   ccamp@ops.ietf.org.



Dubuc et al.             Expires November 2002                  [Page 2]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   This memo does not, in its draft form, specify a standard for the
   Internet community.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119, reference
   [BCP14].


3.  Terminology

   This document uses terminology from the document describing the Link
   Management Protocol [LMP]. An "LMP adjacency" is formed between two
   nodes that support the same capabilities, and LMP messages are
   exchanged between the node pair over control channels that form this
   adjacency. Several control channels can be active at the same time.
   With the exception of messages related to control channel management,
   any time a LMP message needs to be transferred to a neighbor node, it
   can be sent on any of the active control channels. The control chan-
   nels can also be used to exchange MPLS control plane information or
   routing information.

   LMP is designed to support aggregation of one or more data-bearing
   links into a traffic-engineering (TE) link. The data-bearing links
   can be either component links or ports depending on their multiplex-
   ing capability (see [LMP] for distinction between port and component
   link).

   Each TE link is associated with an LMP adjacency, and one or more
   control channels are used to exchange LMP messages for a particular
   adjacency. In turn, control channels are used to manage the TE links
   associated with the LMP adjacency.


4.  The SNMP Management Framework

   The SNMP Management Framework presently consists of five major com-
   ponents:

   -  An overall architecture, described in RFC 2571 [RFC2571].

   -  Mechanisms for describing and naming objects and events for the
      purpose of management.  The first version of this Structure of
      Management Information (SMI) is called SMIv1 and described in
      STD 16, RFC 1155 [RFC1155], STD 16, RFC 1212 [RFC1212] and RFC
      1215 [RFC1215].  The second version, called SMIv2, is described
      in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and
      STD 58, RFC 2580 [RFC2580].



Dubuc et al.             Expires November 2002                  [Page 3]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   -  Message protocols for transferring management information.  The
      first version of the SNMP message protocol is called SNMPv1 and
      described in STD 15, RFC 1157 [RFC1157].  A second version of
      the SNMP message protocol, which is not an Internet standards
      track protocol, is called SNMPv2c and described in RFC 1901
      [RFC1901] and RFC 1906 [RFC1906].  The third version of the
      message protocol is called SNMPv3 and described in RFC 1906
      [RFC1906], RFC 2572 [RFC2572] and RFC 2574 [RFC2574].

   -  Protocol operations for accessing management information.  The
      first set of protocol operations and associated PDU formats is
      described in STD 15, RFC 1157 [RFC1157].  A second set of
      protocol operations and associated PDU formats is described in
      RFC 1905 [RFC1905].

   -  A set of fundamental applications described in RFC 2573
      [RFC2573] and the view-based access control mechanism described
      in RFC 2575 [RFC2575].

   A more detailed introduction to the current SNMP Management Framework
   can be found in RFC 2570 [RFC2570].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  Objects in the MIB are
   defined using the mechanisms defined in the SMI.

   This memo specifies a MIB module that is compliant to the SMIv2.  A
   MIB conforming to the SMIv1 can be produced through the appropriate
   translations.  The resulting translated MIB must be semantically
   equivalent, except where objects or events are omitted because no
   translation is possible (use of Counter64).  Some machine readable
   information in SMIv2 will be converted into textual descriptions in
   SMIv1 during the translation process.  However, this loss of machine
   readable information is not considered to change the semantics of the
   MIB.


5.  Feature Checklist

   The Link Management protocol MIB (LMP-MIB) is designed to satisfy the
   following requirements and constraints:

   -  The MIB supports the enabling and disabling of LMP capability
      on LMP capable interfaces of a photonic switch, optical
      cross-connect or router.

   -  The MIB is used provide information about LMP adjacencies.




Dubuc et al.             Expires November 2002                  [Page 4]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   -  Support is provided for configuration of the keep alive and
      link verification parameters.

   -  The MIB is used to express the mapping between local and remote
      TE links, as well as local and remote interface identifiers for
      port or component link.

   -  Performance counters are provided for measuring LMP
      performance on a per-control channel basis. Performance counters
      are also provided for measuring LMP performance on the data-
      bearing links.

   Note that the LMP MIB goes hand-in-hand with the Link Bundling MIB
   [BUNDLE-MIB]. The TE link table, which is used to associate data-
   bearing links to TE links, is defined in the Link Bundling MIB. The
   TE link table in the LMP MIB contains TE link information specific to
   LMP.


6.  Outline

   Configuring LMP through an optical device involves the following
   steps:

   -  Enabling LMP on LMP capable interfaces through control channel
      configuration.

   -  Optionally specifying link verification parameters.

   -  Configuring the data-bearing links and associating them to the
      appropriate TE link (this association is stored in the
      ifStackTable of the Interfaces Group MIB).

   TE links are managed by the control channels that run between the
   same pair of nodes (LMP adjacency).

6.1.  Summary of LMP MIB

   The MIB objects for performing these actions consist of the following
   tables:

   -  The remote node table (lmpNbrTable) is used to identify the pair
      of nodes that exchange LMP messages over control channels.

   -  The control channel table (lmpControlChannelTable) is used
      for enabling the LMP protocol on LMP-capable interfaces.

   -  The control channel performance table



Dubuc et al.             Expires November 2002                  [Page 5]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


      (lmpControlChannelPerfTable) is used for collecting
      LMP performance counts on a per-control channel basis.

   -  The TE link table (lmpTeLinkTable) is used for
      specifying LMP information associated with TE links.

   -  The link verification table (lmpLinkVerificationTable) is used for
      configuring the LMP link verification parameters of TE links.

   -  The TE link performance table (lmpTeLinkPerfTable) is used for
      collecting LMP performance counts on a per-TE link basis.

   -  The data-bearing link table (lmpDataBearingLinkTable) is used to
      specify the data-bearing links that are associated with TE links.

   -  The data-bearing link performance table
      (lmpDataBearingLinkPerfTable) is used for collecting LMP
      performance counts on data-bearing links.

   These tables are described in the subsequent sections.


7.  Brief Description of MIB Objects

   Sections 7.1-7.3 describe objects pertaining to LMP-capable inter-
   faces. Section 7.4 to 7.7 describes objects for specifying TE links
   and data-bearing links. The MIB objects were derived from the LMP
   document [LMP].


7.1.  lmpNbrTable

   This table identifies the pairs of nodes on which LMP is enabled.


7.2.  lmpControlChannelTable

   This table represents the interfaces that are LMP capable (i.e. capa-
   ble of transmitting LMP messages). A photonic switch, optical cross-
   connect, or router creates an entry in this table for every LMP capa-
   ble interface on that device.


7.3.  lmpControlChannelPerfTable

   This table contains the objects to measure the LMP performance of LMP
   capable interfaces and is an AUGMENT to the lmpControlChannelTable.




Dubuc et al.             Expires November 2002                  [Page 6]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


7.4.  lmpTeLinkTable

   This table represents the TE link information specific to LMP.


7.5.  lmpLinkVerificationTable

   This table augments the lmpTeLinkTable and represents the link verif-
   ication parameters associated with the TE links.


7.6.  lmpTeLinkPerfTable

   This table contains the objects to measure the LMP performance of LMP
   capable interfaces and is an AUGMENT to the lmpTeLinkTable.


7.7.  lmpDataBearingLinkTable

   The data-bearing link table enumerates the data-bearing links that
   are associated with each TE link.


7.8.  lmpDataBearingLinkPerfTable

   This table augments the lmpDataBearingLinkTable. It contains the
   objects to measure the LMP performance of data-bearing links.


8.  Example of LMP Control Channel Setup

   In this section we provide a brief example of using the MIB
   objects described in section 10 to set up an LMP control channel.
   While this example is not meant to illustrate every nuance of the
   MIB, it is intended as an aid to understanding some of the key
   concepts. It is meant to be read after going through the MIB itself.

   Suppose that one would like to form an LMP adjacency between two
   nodes using two control channels. Suppose also that there are
   three data-bearing links. We also assume that the data-bearing
   links are ports (lambdas). We also assume that the link
   verification procedure is not enabled. The following example
   illustrates which rows and corresponding objects might be created
   to accomplish this.

   First, LMP must be enabled between the pair of nodes.

   In lmpNbrTable:



Dubuc et al.             Expires November 2002                  [Page 7]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   {
      lmpNbrNodeId                       = 'c0010101'H, -- 192.1.1.1
      lmpNbrRetransmitInterval           = 10,
      lmpNbrRetransmitTimeoutInterval    = 0,
      lmpNbrAdminStatus                  = up(1),
      lmpNbrRowStatus                    = createAndGo(4)
   }

   Then, the control channels must be set up. These are created in
   the lmpControlChannelTable.

   In lmpControlChannelTable:
   {
      lmpCcId                           = 1,
      lmpCcUnderlyingIfIndex            = 1,
      lmCcIsIf                          = false(1),
      lmpCcAuthentication               = false(1),
      lmpCcConfigRetransmitInterval     = 10,
      lmpCcHelloInterval                = 15,
      lmpCcHelloIntervalMin             = 15,
      lmpCcHelloIntervalMax             = 1000,
      lmpCcHelloDeadInterval            = 45,
      lmpCcHelloDeadIntervalMin         = 45,
      lmpCcHelloDeadIntervalMax         = 1000,
      lmpCcAdminStatus                  = up(1),
      lmpCcRowStatus                    = createAndGo(4)
   }

   {
      lmpCcId                           = 2,
      lmpCcUnderlyingIfIndex            = 2,
      lmCcIsIf                          = false(1),
      lmpCcAuthentication               = false(1),
      lmpCcConfigRetransmitInterval     = 10,
      lmpCcHelloInterval                = 15,
      lmpCcHelloIntervalMin             = 15,
      lmpCcHelloIntervalMax             = 1000,
      lmpCcHelloDeadInterval            = 45,
      lmpCcHelloDeadIntervalMin         = 45,
      lmpCcHelloDeadIntervalMax         = 1000,
      lmpCcAdminStatus                  = up(1),
      lmpCcRowStatus                    = createAndGo(4)
   }

   Next, the three data-bearing links are created. For each data-
   bearing link, an ifEntry with the same ifIndex needs to be created
   beforehand.




Dubuc et al.             Expires November 2002                  [Page 8]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   In lmpDataBearingLinkTable:
   {
      ifIndex                         = 41,
      lmpDataBearingLinkNumberingType = unnumbered(1),
      lmpDataBearingLinkRemoteIfId    = 47,
      lmpDataBearingLinkRowStatus     = createAndGo(4)
   }

   {
      ifIndex                         = 43,
      lmpDataBearingLinkNumberingType = unnumbered(1),
      lmpDataBearingLinkRemoteIfId    = 42,
      lmpDataBearingLinkRowStatus     = createAndGo(4)
   }

   {
      ifIndex                         = 44,
      lmpDataBearingLinkNumberingType = unnumbered(1),
      lmpDataBearingLinkRemoteIfId    = 48,
      lmpDataBearingLinkRowStatus     = createAndGo(4)
   }

   Note that the data-bearing link type (lmpDataBearingLinkType) does
   not need to be provisioned as it is automatically populated by the
   node. The definition of the protection role (primary or
   secondary) for the data-bearing links is stored in the
   dataBearingChannelTable of the Link Bundling MIB [BUNDLE-MIB].

   Then, a TE link is created as an ifEntry with ifType teLink in
   the ifTable.

   Once the TE link is created in the ifTable, a TE link entry
   is created in the LMP MIB to specify TE link information specific
   to LMP.

   In lmpTeLinkTable:
   {
      ifIndex                    = 20,
      lmpTeLinkVerification      = true(2),
      lmpTeLinkFaultManagement   = true(2),
      lmpTeLinkDwdm              = false(1),
      lmpTeLinkBitRate           = 100000,
      lmpTeLinkWavelength        = 0,
      lmpTeLinkRowStatus         = createAndGo(4)
   }

   The association between the data-bearing links and the TE links is
   stored in the ifStackTable [IF-MIB].



Dubuc et al.             Expires November 2002                  [Page 9]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   In parallel with the entry created in the lmpTeLinkTable, an entry
   may be created in the teLinkTable of Link Bundling MIB
   [BUNDLE-MIB].


9.  Application of the Interfaces Group to LMP

   The Interfaces Group [IFMIB] defines generic managed objects for
   managing interfaces. This memo contains the media-specific
   extensions to the Interfaces Group for managing LMP control channels
   that are modeled as interfaces. If the control channel as defined in
   the lmpControlChannelTable is modeled as an ifEntry, then the
   following definition applies. An lmpControlChannelTable entry is
   designated as being represented as an Interfaces MIB ifEntry if the
   lmpControlChannelEntry object lmpCcIsIf is set to true (2). In this
   case, the control channel SHOULD be modeled as an ifEntry and
   provide appropriate interface stacking as defined below.

   This memo assumes the interpretation of the Interfaces Group to be
   in accordance with [IFMIB] which states that the interfaces table
   (ifTable) contains information on the managed resource's
   interfaces and that each sub-layer below the internetwork layer of
   a network interface is considered an interface. Since the LMP
   interface only carries control traffic, it is considered to be below
   the internetwork layer. Thus, the LMP interface may be represented
   as an entry in the ifTable. The inter-relation of entries in the
   ifTable is defined by Interfaces Stack Group defined in [IFMIB].

   When LMP control channels are modeled as interfaces, the interface
   stack table must appear as follows for the LMP control channel
   interfaces:

   +----------------------------------------+
   | LMP-interface ifType = lmp(TBD)        +
   +----------------------------------------+
   | Underlying Layer...                    +
   +----------------------------------------+

   In the above diagram, "Underlying Layer..." refers to the ifIndex
   of any interface type over which the LMP interface will transmit
   its traffic. Note that if the underlying layer provides multiple
   access to its media (i.e.: Ethernet), then it is possible to stack
   multiple LMP interfaces on top of this interface in parallel.


9.1.  Support of the LMP Layer by ifTable

   Some specific interpretations of ifTable for the LMP layer



Dubuc et al.             Expires November 2002                 [Page 10]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   follow.

   Object        Use for the LMP layer

   ifIndex       Each LMP interface may be represented by an ifEntry.

   ifDescr       Description of the LMP interface.

   ifType        The value that is allocated for LMP is TBD.
                 This number will be assigned by the IANA.

   ifSpeed       The total bandwidth in bits per second for use by
                 the LMP layer.

   ifPhysAddress Unused.

   ifAdminStatus This variable indicates the administrator's intent
                 as to whether LMP should be enabled, disabled, or
                 running in some diagnostic testing mode on this
                 interface. Also see [IFMIB].

   ifOperStatus  This value reflects the actual or operational
                 status of LMP on this interface.

   ifLastChange  See [IFMIB].

   ifInOctets    The number of received octets over the interface,
                 i.e., the number of octets received as LMP
                 packets.

   ifOutOctets   The number of transmitted octets over the
                 interface, i.e., the number of octets transmitted
                 as LMP packets.

   ifInErrors    The number of LMP packets dropped due to
                 uncorrectable errors.

   ifInUnknownProtos
                 The number of received packets discarded during
                 packet header validation, including packets with
                 unrecognized label values.

   ifOutErrors   See [IFMIB].

   ifName        Textual name (unique on this system) of the
                 interface or an octet string of zero length.

   ifLinkUpDownTrapEnable



Dubuc et al.             Expires November 2002                 [Page 11]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


                 Default is disabled (2).

   ifConnectorPresent
                 Set to false (2).

   ifHighSpeed   See [IFMIB].

   ifHCInOctets  The 64-bit version of ifInOctets; supported if
                 required by the compliance statements in [IFMIB].

   ifHCOutOctets The 64-bit version of ifOutOctets; supported if
                 required by the compliance statements in [IFMIB].

   ifAlias       The non-volatile 'alias' name for the interface as
                 specified by a network manager.

   ifCounterDiscontinuityTime
                 See [IFMIB].


10.  LMP MIB Definitions

LMP-MIB DEFINITIONS ::= BEGIN

IMPORTS
   MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
   experimental, Unsigned32, Counter32, TimeTicks
      FROM SNMPv2-SMI

   MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
      FROM SNMPv2-CONF

   TEXTUAL-CONVENTION, TruthValue, RowStatus, StorageType,
   TimeStamp
      FROM SNMPv2-TC

   InterfaceIndexOrZero, ifIndex
      FROM IF-MIB

   InetAddressType, InetAddress
      FROM INET-ADDRESS-MIB

   teLinkRemoteIpAddr, teLinkIncomingIfId
      FROM LINK-BUNDLING-MIB;

lmpMIB MODULE-IDENTITY
   LAST-UPDATED "200205291200Z"  -- 29 May 2002 12:00:00 EST
   ORGANIZATION "Common Control and Measurement Protocols (CCAMP)



Dubuc et al.             Expires November 2002                 [Page 12]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


                 Working Group"
   CONTACT-INFO
       "        Martin Dubuc
        Postal: Meriton Networks
                3026 Solandt Road
                Kanata, ON, CANADA K2K 2A5
        Tel:    +1-613-270-9279 x253
        Email:  martin.dubuc@meriton.com

                Sudheer Dharanikota
        Postal: Nayna Networks, Inc.
                157 Topaz Street
                Milipitas, CA 95035
        Tel:    +1-408-956-8000 x357
        Email:  sudheer@nayna.com

                Thomas D. Nadeau
        Postal: Cisco Systems, Inc.
                300 Apollo Drive
                Chelmsford, MA 01824
        Tel:    +1-978-244-3051
        Email:  tnadeau@cisco.com

                Jonathan P. Lang
        Postal: Calient Networks, Inc.
                25 Castilian Drive
                Goleta, CA 93117
        Email:  jplang@calient.net

                Evan McGinnis
        Postal: Calient Networks, Inc.
                5853 Rue Ferrari
                San Jose, CA 95138
        Email:  evan@calient.net"


   DESCRIPTION
       "This MIB contains managed object definitions for the
        Link Management Protocol (LMP) as
        defined in: Lang, J., Mitra, K., Drake, J., Kompella, K.,
        Rekhter, Y., Berger, L., Saha, D.,
        Basak, D., Sandick, H., Zinin, A., and
        Rajagopalan, B., Link Management Protocol,
        Internet Draft <draft-ietf-ccamp-lmp-03.txt>,
        March 2002."

   -- Revision history.
   REVISION



Dubuc et al.             Expires November 2002                 [Page 13]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


       "200205291200Z"  -- 29 May 2002 12:00:00 EST
   DESCRIPTION
      "Addresses Last Call comments.
       - Fixed syntax problems reported by SMICng and smilint.
       - Added lmpRemoteCcIpAddrType and lmpRemoteCcIpAddr.
       - Added lmpTeLinkPerfTable.
       - Added lmpDataBearingLinkIpAddr.
       - Added lmpTeLinkNotDegraded notification."
   REVISION
       "200202261200Z"  -- 26 February 2002 12:00:00 EST
   DESCRIPTION
      "- Used latest MIB boiler plate.
       - Added lmpFullModuleCompliance conformance statement.
       - Replaced IpAddress with InetAddress.
       - Added lmpOperStatus.
       - Added lmpCcHelloIntervalNegotiated and
         lmpCcHelloDeadIntervalNegotiated.
       - Converted all 64-bit counters to 32-bit counters.
       - Added counters for all LMP message types.
       - Added counters to monitor data-bearing link tests.
       - Reintroduced lmpNbrRetransmitTimeout.
       - Added lmpDataBearingLinkNumberingType and
         lmpDataBearingLinkRemoteIpAddress.
       - Split data-bearing link operational status into active and
         passive operational status.
       - Updated description of all row status and storage type objects.
       - Updated references."
   REVISION
       "200110211200Z"  -- 21 October 2001 12:00:00 EST
   DESCRIPTION
      "- Minor syntax fixes.
       - Added lmpCcId. Changed type of lmpRemoteCcId.
       - Updated lmpTeLinkEncodingType.
       - Removed lmpRemoteTeLinkType and lmpRemoteTeLinkId (their
         content can be derived from LINK-BUNDLING-MIB).
       - Added lmpCcLastChange, lmpCcCounterDiscontinuityTime and
         lmpDataBearingLinkCounterDiscontinuityTime.
       - Moved lmpTeLinkBitRate and lmpTeLinkWavelength to
         lmpLinkVerificationTable.
       - Updated lmpDataBearingLinkOperStatus.
       - Modified performance counters to account for changes in
         channel status message types.
       - Changed indices for lmpTeLinkPropertyMismatch and
         lmpDataBearingLinkPropertyMismatch notifications.
       - Renamed lmpNbrLinkSumRetransmitInterval. Removed
         lmpNbrRetransmitTimeout.
       - Added lmpCcUnderlyingIfId, lmpCcIsIf and lmpCcSetupRole."
   REVISION



Dubuc et al.             Expires November 2002                 [Page 14]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


       "200105221200Z"  -- 22 May 2001 12:00:00 EST
   DESCRIPTION
      "Updates based on IETF-50 feedback. Aligned with
       upcoming version of LMP draft."
   REVISION
       "200102221200Z"  -- 22 February 2001 12:00:00 EST
   DESCRIPTION
      "Updates based on MPLS mailing list feedback."
   REVISION
       "200101261200Z"  -- 26 January 2001 12:00:00 EST
   DESCRIPTION
      "Initial draft version."
   ::= { experimental 113 }


-- Textual Conventions

LmpInterval ::= TEXTUAL-CONVENTION
   DISPLAY-HINT "d"
   STATUS        current
   DESCRIPTION
       "The interval delay in milliseconds."
   SYNTAX        Unsigned32 (1..65535)

LmpRetransmitInterval ::= TEXTUAL-CONVENTION
   DISPLAY-HINT "d"
   STATUS        current
   DESCRIPTION
       "The retransmission interval delay in milliseconds."
   SYNTAX        Unsigned32 (1..4294967295)


-- Top level components of this MIB

-- Notifications
lmpNotifications OBJECT IDENTIFIER ::= { lmpMIB 0 }
-- Tables, Scalars
lmpObjects       OBJECT IDENTIFIER ::= { lmpMIB 1 }
-- Conformance
lmpConformance   OBJECT IDENTIFIER ::= { lmpMIB 2 }


lmpAdminStatus OBJECT-TYPE
   SYNTAX        INTEGER { up(1), down(2) }
   MAX-ACCESS    read-write
   STATUS        current
   DESCRIPTION
       "The desired operational status of LMP on the node."



Dubuc et al.             Expires November 2002                 [Page 15]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   DEFVAL        { up }
   ::= { lmpObjects 1 }

lmpOperStatus OBJECT-TYPE
   SYNTAX        INTEGER { up(1), down(2) }
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "The actual operational status of LMP on the node."
   ::= { lmpObjects 2 }


-- LMP Neighbor Table

lmpNbrTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF LmpNbrEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies the neighbor node(s) to which control channels
        may be established."
   ::= { lmpObjects 3 }

lmpNbrEntry OBJECT-TYPE
   SYNTAX        LmpNbrEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table is created by a LMP-enabled device for
        every pair of nodes that can establish control channels."
   INDEX         { lmpNbrNodeId }
   ::= { lmpNbrTable 1 }

LmpNbrEntry ::= SEQUENCE {
  lmpNbrNodeId              InetAddress,
  lmpNbrRetransmitInterval  LmpRetransmitInterval,
  lmpNbrRetransmitTimeout   Unsigned32,
  lmpNbrAdminStatus         INTEGER,
  lmpNbrOperStatus          INTEGER,
  lmpNbrRowStatus           RowStatus,
  lmpNbrStorageType         StorageType
}

lmpNbrNodeId OBJECT-TYPE
   SYNTAX        InetAddress (SIZE(4))
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION



Dubuc et al.             Expires November 2002                 [Page 16]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


       "This is a unique index for an entry in the LmpNbrTable.
        This value represents the remote Node ID. The Node ID
        address type must be IPv4."
   ::= { lmpNbrEntry 1 }

lmpNbrRetransmitInterval OBJECT-TYPE
   SYNTAX        LmpRetransmitInterval
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object specifies the interval that is used for the
        retransmission of LinkSummary, BeginVerify, EndVerify,
        TestStatusSuccess, TestStatusFailure, ChannelStatus and
        ChannelStatusRequest messages."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   ::= { lmpNbrEntry 2 }

lmpNbrRetransmitTimeout OBJECT-TYPE
   SYNTAX        Unsigned32
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object specifies the LinkSummary, BeginVerify, EndVerify,
        TestStatusSuccess, TestStatusFailure, ChannelStatus and
        ChannelStatusRequest retransmission timeout period. If the specified
        timeout expires and the message has not yet been acknowledged,
        a node can stop retransmitting the message. A value of 0 is used
        to indicate that a node should never stop retransmission."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   DEFVAL        { 0 }
   ::= { lmpNbrEntry 7 }

lmpNbrAdminStatus OBJECT-TYPE
   SYNTAX        INTEGER { up(1), down(2) }
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The desired operational status of LMP to this remote node."
   ::= { lmpNbrEntry 3 }




Dubuc et al.             Expires November 2002                 [Page 17]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


lmpNbrOperStatus OBJECT-TYPE
   SYNTAX        INTEGER { up(1), down(2) }
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "The actual operational status of LMP to this remote node."
   ::= { lmpNbrEntry 4 }

lmpNbrRowStatus OBJECT-TYPE
   SYNTAX        RowStatus
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This variable is used to create, modify, and/or
        delete a row in this table. All read-create objects
        can only be changed when lmpNbrRowStatus is active."
   ::= { lmpNbrEntry 5 }

lmpNbrStorageType OBJECT-TYPE
   SYNTAX        StorageType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The storage type for this conceptual row in the
        lmpNbrTable. Conceptual rows having the value
        'permanent' need not allow write-access to any
        columnar object in the row."
   ::= { lmpNbrEntry 6 }

-- End of lmpNbrTable


lmpCcHelloIntervalDefault OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-write
   STATUS        current
   DESCRIPTION
       "This object specifies the default value for the HelloInterval
        parameter used in the Hello protocol keep-alive phase. It
        indicates how frequently LMP Hello messages will be sent. It
        is used a the default value for lmpCcHelloInterval."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   ::= { lmpObjects 4 }




Dubuc et al.             Expires November 2002                 [Page 18]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


lmpCcHelloIntervalDefaultMin OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-write
   STATUS        current
   DESCRIPTION
       "This object specifies the default minimum value for the
        HelloInterval parameter. It is used as a default value
        for lmpCcHelloIntervalMin."
   ::= { lmpObjects 5 }

lmpCcHelloIntervalDefaultMax OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-write
   STATUS        current
   DESCRIPTION
       "This object specifies the default maximum value for the
        HelloInterval parameter. It is used as a default value
        for lmpCcHelloIntervalMax."
   ::= { lmpObjects 6 }

lmpCcHelloDeadIntervalDefault OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-write
   STATUS        current
   DESCRIPTION
       "This object specifies the default HelloDeadInterval parameter to
        use in the Hello protocol keep-alive phase. It indicates how long
        a device should wait before declaring the control channel dead.
        The HelloDeadInterval parameter should be at least three times the
        value of HelloInterval. It is used as a default value for
        lmpCcHelloDeadInterval."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   ::= { lmpObjects 7 }

lmpCcHelloDeadIntervalDefaultMin OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-write
   STATUS        current
   DESCRIPTION
       "This object specifies the default minimum value for the
        HelloDeadInterval parameter. It is used as a default value
        for lmpCcHelloDeadIntervalMin."
   ::= { lmpObjects 8 }




Dubuc et al.             Expires November 2002                 [Page 19]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


lmpCcHelloDeadIntervalDefaultMax OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-write
   STATUS        current
   DESCRIPTION
       "This object specifies the default maximum value for the
        HelloDeadInterval parameter. It is used as a default value
        for lmpCcHelloDeadIntervalMax."
   ::= { lmpObjects 9 }


-- LMP Control Channel Table

lmpControlChannelTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF LmpControlChannelEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies LMP control channel information."
   ::= { lmpObjects 10 }

lmpControlChannelEntry OBJECT-TYPE
   SYNTAX        LmpControlChannelEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table is created by a LMP-enabled device for
        every control channel. Whenever a new entry is created with lmpCcIsIf
        set to true(2), then a corresponding entry is created in ifTable as
        well (see RFC 2863)."
   INDEX         { lmpCcId }
   ::= { lmpControlChannelTable 1 }

LmpControlChannelEntry ::= SEQUENCE {
  lmpCcId                           Unsigned32,
  lmpCcUnderlyingIfIndex            InterfaceIndexOrZero,
  lmpCcIsIf                         TruthValue,
  lmpCcNbrNodeId                    InetAddress,
  lmpRemoteCcId                     Unsigned32,
  lmpRemoteCcIpAddrType             InetAddressType,
  lmpRemoteCcIpAddr                 InetAddress,
  lmpCcSetupRole                    INTEGER,
  lmpCcAuthentication               TruthValue,
  lmpCcConfigRetransmitInterval     LmpRetransmitInterval,
  lmpCcConfigRetransmitTimeout      Unsigned32,
  lmpCcHelloInterval                LmpInterval,
  lmpCcHelloIntervalMin             LmpInterval,
  lmpCcHelloIntervalMax             LmpInterval,



Dubuc et al.             Expires November 2002                 [Page 20]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


  lmpCcHelloIntervalNegotiated      LmpInterval,
  lmpCcHelloDeadInterval            LmpInterval,
  lmpCcHelloDeadIntervalMin         LmpInterval,
  lmpCcHelloDeadIntervalMax         LmpInterval,
  lmpCcHelloDeadIntervalNegotiated  LmpInterval,
  lmpCcLastChange                   TimeTicks,
  lmpCcAdminStatus                  INTEGER,
  lmpCcOperStatus                   INTEGER,
  lmpCcRowStatus                    RowStatus,
  lmpCcStorageType                  StorageType
}

lmpCcId OBJECT-TYPE
   SYNTAX        Unsigned32
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This value represents the local control channel identifier."
   ::= { lmpControlChannelEntry 1 }

lmpCcUnderlyingIfIndex OBJECT-TYPE
   SYNTAX        InterfaceIndexOrZero
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This value represents the underlying interface index, i.e. the
        interface index of the interface over which the LMP interface
        will transmit its traffic. If set to 0, then the control channel
        is not associated with any underlying interface. If the control
        channel is not associated with an underlying interface, the control
        channel's operational status must not be up(1), nor should the
        control channel forward or receive traffic."
   ::= { lmpControlChannelEntry 2 }

lmpCcIsIf OBJECT-TYPE
   SYNTAX        TruthValue
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "Denotes whether or not this control channel corresponds to
        an interface represented in the interfaces group table."
   ::= { lmpControlChannelEntry 3 }

lmpCcNbrNodeId OBJECT-TYPE
   SYNTAX        InetAddress (SIZE(4))
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION



Dubuc et al.             Expires November 2002                 [Page 21]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


       "This is the Node ID of the control channel remote node.
        This value is either configured or gets created by the node
        when a Config message is received or when an outgoing Config
        message is acknowledged by the remote node. The Node ID
        address type must be IPv4."
   ::= { lmpControlChannelEntry 4 }

lmpRemoteCcId OBJECT-TYPE
   SYNTAX        Unsigned32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This value represents the remote control channel identifier. It is
        determined during the negotiation phase. A value
        of zero means that the remote control channel identifier has not
        yet been learnt."
   ::= { lmpControlChannelEntry 5 }

lmpRemoteCcIpAddrType OBJECT-TYPE
   SYNTAX        InetAddressType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This value represents the remote control channel IP address type.
        In point-to-point configuration, this value can be set to
        unknown(0)."
   ::= { lmpControlChannelEntry 6 }

lmpRemoteCcIpAddr OBJECT-TYPE
   SYNTAX        InetAddress
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This value represents the remote control channel IP address for
        non point-to-point configuration. For point-to-point configuration,
        this value can be set to null."
   ::= { lmpControlChannelEntry 7 }

lmpCcSetupRole OBJECT-TYPE
   SYNTAX        INTEGER { active(1), passive(2) }
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The role that this node should take during establishment of this
        control channel. An active node will initiate establishment. A
        passive node will wait for the remote node to initiate. A pair
        of nodes that both take the passive role will never establish
        communications."



Dubuc et al.             Expires November 2002                 [Page 22]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   DEFVAL        { active }
   ::= { lmpControlChannelEntry 8 }

lmpCcAuthentication OBJECT-TYPE
   SYNTAX        TruthValue
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object indicates whether the control channel should use
        authentication."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   ::= { lmpControlChannelEntry 9 }

lmpCcConfigRetransmitInterval OBJECT-TYPE
   SYNTAX        LmpRetransmitInterval
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object specifies the interval that is used for the
        retransmission of Config messages during the parameter
        negotiation phase."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   ::= { lmpControlChannelEntry 10 }

lmpCcConfigRetransmitTimeout OBJECT-TYPE
   SYNTAX        Unsigned32
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object specifies the Config retransmission timeout
        period. If the specified timeout expires and no Config,
        ConfigAck or ConfigNack message has been received, a node
        can stop retransmitting Config messages on the control
        channel. A value of 0 is used to indicate that a node should
        never stop retransmission. This parameter (if non-zero)
        should be greater than lmpCcConfigRetransmitInterval."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,



Dubuc et al.             Expires November 2002                 [Page 23]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


        B. Rajagopalan, March 2002."
   DEFVAL        { 0 }
   ::= { lmpControlChannelEntry 11 }

lmpCcHelloInterval OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object specifies the value of the HelloInterval
        parameter. The default value for this object should be
        set to lmpCcHelloIntervalDefault."
   ::= { lmpControlChannelEntry 12 }

lmpCcHelloIntervalMin OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object specifies the minimum value for the
        HelloInterval parameter. The default value for this
        object should be set to lmpCcHelloIntervalMinDefault."
   ::= { lmpControlChannelEntry 13 }

lmpCcHelloIntervalMax OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object specifies the maximum value for the
        HelloInterval parameter. The default value for this
        object should be set to lmpCcHelloIntervalMaxDefault."
   ::= { lmpControlChannelEntry 14 }

lmpCcHelloIntervalNegotiated OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "Once the control channel is active, this object represents
        the negotiated HelloInterval value."
   ::= { lmpControlChannelEntry 15 }

lmpCcHelloDeadInterval OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION



Dubuc et al.             Expires November 2002                 [Page 24]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


       "This object specifies the value of the HelloDeadInterval
        parameter. The default value for this object should be
        set to lmpCcHelloDeadIntervalDefault."
   ::= { lmpControlChannelEntry 16 }

lmpCcHelloDeadIntervalMin OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object specifies the minimum value for the
        HelloDeadInterval parameter. The default value for this
        object should be set to lmpCcHelloDeadIntervalMinDefault."
   ::= { lmpControlChannelEntry 17 }

lmpCcHelloDeadIntervalMax OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object specifies the maximum value for the
        HelloDeadInterval parameter. The default value for this
        object should be set to lmpCcHelloIntervalMaxDefault."
   ::= { lmpControlChannelEntry 18 }

lmpCcHelloDeadIntervalNegotiated OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "Once the control channel is active, this object represents
        the negotiated HelloDeadInterval value."
   ::= { lmpControlChannelEntry 19 }

lmpCcLastChange OBJECT-TYPE
   SYNTAX       TimeTicks
   MAX-ACCESS   read-only
   STATUS       current
   DESCRIPTION
       "The value of sysUpTime at the time the control channel entered
        its current operational state. If the current state was
        entered prior to the last re-initialization of the local
        network management subsystem, then this object contains a
        zero value."
   ::= { lmpControlChannelEntry 20 }

lmpCcAdminStatus OBJECT-TYPE
   SYNTAX        INTEGER { up(1), down(2) }



Dubuc et al.             Expires November 2002                 [Page 25]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The desired operational status of this control channel."
   ::= { lmpControlChannelEntry 21 }

lmpCcOperStatus OBJECT-TYPE
   SYNTAX        INTEGER {
                     up(1),
                     down(2),
                     configSnd(3),
                     configRcv(4),
                     active(5),
                     goingDown(6)
                 }
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "The actual operational status of this control channel
        interface."
   ::= { lmpControlChannelEntry 22 }

lmpCcRowStatus OBJECT-TYPE
   SYNTAX        RowStatus
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This variable is used to create, modify, and/or
        delete a row in this table. All read-create objects
        can only be changed when lmpCcRowStatus is active."
   ::= { lmpControlChannelEntry 23 }

lmpCcStorageType OBJECT-TYPE
   SYNTAX        StorageType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The storage type for this conceptual row in the
        lmpControlChannelTable. Conceptual rows having the value
        'permanent' need not allow write-access to any
        columnar object in the row."
   ::= { lmpControlChannelEntry 24 }

-- End of lmpControlChannelTable


-- LMP Control Channel Performance Table




Dubuc et al.             Expires November 2002                 [Page 26]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


lmpControlChannelPerfTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF LmpControlChannelPerfEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies LMP control channel performance counters."
   ::= { lmpObjects 11 }

lmpControlChannelPerfEntry OBJECT-TYPE
   SYNTAX        LmpControlChannelPerfEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table is created by a LMP-enabled device for
        every control channel."
   AUGMENTS      { lmpControlChannelEntry }
   ::= { lmpControlChannelPerfTable 1 }

LmpControlChannelPerfEntry ::= SEQUENCE {
  lmpCcInOctets                       Counter32,
  lmpCcInDiscards                     Counter32,
  lmpCcInErrors                       Counter32,
  lmpCcOutOctets                      Counter32,
  lmpCcOutDiscards                    Counter32,
  lmpCcOutErrors                      Counter32,
  lmpCcConfigReceived                 Counter32,
  lmpCcConfigSent                     Counter32,
  lmpCcConfigRetransmit               Counter32,
  lmpCcConfigAckReceived              Counter32,
  lmpCcConfigAckSent                  Counter32,
  lmpCcConfigNackReceived             Counter32,
  lmpCcConfigNackSent                 Counter32,
  lmpCcHelloReceived                  Counter32,
  lmpCcHelloSent                      Counter32,
  lmpCcBeginVerifyReceived            Counter32,
  lmpCcBeginVerifySent                Counter32,
  lmpCcBeginVerifyRetransmit          Counter32,
  lmpCcBeginVerifyAckReceived         Counter32,
  lmpCcBeginVerifyAckSent             Counter32,
  lmpCcBeginVerifyNackReceived        Counter32,
  lmpCcBeginVerifyNackSent            Counter32,
  lmpCcEndVerifyReceived              Counter32,
  lmpCcEndVerifySent                  Counter32,
  lmpCcEndVerifyRetransmit            Counter32,
  lmpCcEndVerifyAckReceived           Counter32,
  lmpCcEndVerifyAckSent               Counter32,
  lmpCcTestStatusSuccessReceived      Counter32,
  lmpCcTestStatusSuccessSent          Counter32,



Dubuc et al.             Expires November 2002                 [Page 27]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


  lmpCcTestStatusSuccessRetransmit    Counter32,
  lmpCcTestStatusFailureReceived      Counter32,
  lmpCcTestStatusFailureSent          Counter32,
  lmpCcTestStatusFailureRetransmit    Counter32,
  lmpCcTestStatusAckReceived          Counter32,
  lmpCcTestStatusAckSent              Counter32,
  lmpCcLinkSummaryReceived            Counter32,
  lmpCcLinkSummarySent                Counter32,
  lmpCcLinkSummaryRetransmit          Counter32,
  lmpCcLinkSummaryAckReceived         Counter32,
  lmpCcLinkSummaryAckSent             Counter32,
  lmpCcLinkSummaryNackReceived        Counter32,
  lmpCcLinkSummaryNackSent            Counter32,
  lmpCcChannelStatusReceived          Counter32,
  lmpCcChannelStatusSent              Counter32,
  lmpCcChannelStatusRetransmit        Counter32,
  lmpCcChannelStatusAckReceived       Counter32,
  lmpCcChannelStatusAckSent           Counter32,
  lmpCcChannelStatusRequestReceived   Counter32,
  lmpCcChannelStatusRequestSent       Counter32,
  lmpCcChannelStatusRequestRetransmit Counter32,
  lmpCcChannelStatusResponseSent      Counter32,
  lmpCcChannelStatusResponseReceived  Counter32,
  lmpCcCounterDiscontinuityTime       TimeStamp
}

lmpCcInOctets OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "The total number of LMP message octets received on the
             control channel."
    ::= { lmpControlChannelPerfEntry 1 }

lmpCcInDiscards OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "The number of inbound packets which were chosen to be
             discarded even though no errors had been detected. One
             possible reason for discarding such a packet could be to
             free up buffer space."
    ::= { lmpControlChannelPerfEntry 2 }

lmpCcInErrors OBJECT-TYPE
    SYNTAX      Counter32



Dubuc et al.             Expires November 2002                 [Page 28]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
            "The number of inbound packets that contained errors
             preventing them from being processed by LMP."
    ::= { lmpControlChannelPerfEntry 3 }

lmpCcOutOctets OBJECT-TYPE
    SYNTAX       Counter32
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
            "The total number of LMP message octets transmitted out of
             the control channel."
    ::= { lmpControlChannelPerfEntry 4 }

lmpCcOutDiscards OBJECT-TYPE
    SYNTAX       Counter32
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
            "The number of outbound packets which were chosen to be
             discarded even though no errors had been detected to prevent
             their being transmitted. One possible reason for discarding
             such a packet could be to free up buffer space."
    ::= { lmpControlChannelPerfEntry 5 }

lmpCcOutErrors OBJECT-TYPE
    SYNTAX       Counter32
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
            "The number of outbound packets that could not be
             transmitted because of errors."
    ::= { lmpControlChannelPerfEntry 6 }

lmpCcConfigReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of Config messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 7 }

lmpCcConfigSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only



Dubuc et al.             Expires November 2002                 [Page 29]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   STATUS        current
   DESCRIPTION
       "This object counts the number of Config messages that have
        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 8 }

lmpCcConfigRetransmit OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of Config messages that
        have been retransmitted over this control channel."
   ::= { lmpControlChannelPerfEntry 9 }

lmpCcConfigAckReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ConfigAck messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 10 }

lmpCcConfigAckSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ConfigAck messages that have
        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 11 }

lmpCcConfigNackReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ConfigNack messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 12 }

lmpCcConfigNackSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ConfigNack messages that have



Dubuc et al.             Expires November 2002                 [Page 30]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 13 }

lmpCcHelloReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of Hello messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 14 }

lmpCcHelloSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of Hello messages that have
        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 15 }

lmpCcBeginVerifyReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of BeginVerify messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 16 }

lmpCcBeginVerifySent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of BeginVerify messages that have
        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 17 }

lmpCcBeginVerifyRetransmit OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of BeginVerify messages that
        have been retransmitted over this control channel."
   ::= { lmpControlChannelPerfEntry 18 }




Dubuc et al.             Expires November 2002                 [Page 31]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


lmpCcBeginVerifyAckReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of BeginVerifyAck messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 19 }

lmpCcBeginVerifyAckSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of BeginVerifyAck messages that have
        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 20 }

lmpCcBeginVerifyNackReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of BeginVerifyNack messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 21 }

lmpCcBeginVerifyNackSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of BeginVerifyNack messages that have
        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 22 }

lmpCcEndVerifyReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of EndVerify messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 23 }

lmpCcEndVerifySent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only



Dubuc et al.             Expires November 2002                 [Page 32]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   STATUS        current
   DESCRIPTION
       "This object counts the number of EndVerify messages that have
        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 24 }

lmpCcEndVerifyRetransmit OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of EndVerify messages that
        have been retransmitted over this control channel."
   ::= { lmpControlChannelPerfEntry 25 }

lmpCcEndVerifyAckReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of EndVerifyAck messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 26 }

lmpCcEndVerifyAckSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of EndVerifyAck messages that have
        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 27 }

lmpCcTestStatusSuccessReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of TestStatusSuccess messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 28 }

lmpCcTestStatusSuccessSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of TestStatusSuccess messages that have



Dubuc et al.             Expires November 2002                 [Page 33]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 29 }

lmpCcTestStatusSuccessRetransmit OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of TestStatusSuccess messages that
        have been retransmitted over this control channel."
   ::= { lmpControlChannelPerfEntry 30 }

lmpCcTestStatusFailureReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of TestStatusFailure messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 31 }

lmpCcTestStatusFailureSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of TestStatusFailure messages that have
        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 32 }

lmpCcTestStatusFailureRetransmit OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of TestStatusFailure messages that
        have been retransmitted over this control channel."
   ::= { lmpControlChannelPerfEntry 33 }

lmpCcTestStatusAckReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of TestStatusAck messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 34 }




Dubuc et al.             Expires November 2002                 [Page 34]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


lmpCcTestStatusAckSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of TestStatusAck messages that have
        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 35 }

lmpCcLinkSummaryReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of LinkSummary messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 36 }

lmpCcLinkSummarySent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of LinkSummary messages that have
        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 37 }

lmpCcLinkSummaryRetransmit OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of LinkSummary messages that
        have been retransmitted over this control channel."
   ::= { lmpControlChannelPerfEntry 38 }

lmpCcLinkSummaryAckReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of LinkSummaryAck messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 39 }

lmpCcLinkSummaryAckSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only



Dubuc et al.             Expires November 2002                 [Page 35]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   STATUS        current
   DESCRIPTION
       "This object counts the number of LinkSummaryAck messages that have
        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 40 }

lmpCcLinkSummaryNackReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of LinkSummaryNack messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 41 }

lmpCcLinkSummaryNackSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of LinkSummaryNack messages that have
        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 42 }

lmpCcChannelStatusReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatus messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 43 }

lmpCcChannelStatusSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatus messages that have
        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 44 }

lmpCcChannelStatusRetransmit OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatus messages that have



Dubuc et al.             Expires November 2002                 [Page 36]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


        been retransmitted on this control channel."
   ::= { lmpControlChannelPerfEntry 45 }

lmpCcChannelStatusAckReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatusAck messages that have
        been received on this control channel."
   ::= { lmpControlChannelPerfEntry 46 }

lmpCcChannelStatusAckSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatus messages that have
        been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 47 }

lmpCcChannelStatusRequestReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatusRequest messages that
        have been received on this control channel."
   ::= { lmpControlChannelPerfEntry 48 }

lmpCcChannelStatusRequestSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatusRequest messages that
        have been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 49 }

lmpCcChannelStatusRequestRetransmit OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatusRequest messages that
        have been retransmitted on this control channel."
   ::= { lmpControlChannelPerfEntry 50 }




Dubuc et al.             Expires November 2002                 [Page 37]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


lmpCcChannelStatusResponseReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatusResponse messages that
        have been received on this control channel."
   ::= { lmpControlChannelPerfEntry 51 }

lmpCcChannelStatusResponseSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatusResponse messages that
        have been sent on this control channel."
   ::= { lmpControlChannelPerfEntry 52 }

lmpCcCounterDiscontinuityTime OBJECT-TYPE
    SYNTAX       TimeStamp
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "The value of sysUpTime on the most recent occasion at which
         any one or more of this control channel's counters suffered a
         discontinuity. The relevant counters are the specific
         instances associated with this control channel of any Counter32
         object contained in the lmpControlChannelPerfTable. If
         no such discontinuities have occurred since the last re-
         initialization of the local management subsystem, then this
         object contains a zero value."
    ::= { lmpControlChannelPerfEntry 53 }

-- End of lmpControlChannelPerfTable


-- LMP TE Link Table

lmpTeLinkTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF LmpTeLinkEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table contains a collection of TE link."
   ::= { lmpObjects 12 }

lmpTeLinkEntry OBJECT-TYPE
   SYNTAX        LmpTeLinkEntry



Dubuc et al.             Expires November 2002                 [Page 38]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table exists for each ifEntry with an
        ifType of teLink(TBD), i.e. for every TE link. An ifEntry
        with an ifIndex must exist before the corresponding
        teLinkEntry is created. If a TE link entry in the ifTable is
        destroyed, then so is the corresponding entry in the
        teLinkTable. The administrative status value is controlled
        from the ifEntry. Setting the administrative status to
        testing prompts LMP to start link verification on the TE link.
        Information about the TE link that is not LMP specific is also
        contained in teLinkTable [BUNDLE-MIB]."
   INDEX         { ifIndex }
   ::= { lmpTeLinkTable 1 }

LmpTeLinkEntry ::= SEQUENCE {
  lmpTeLinkNbrNodeId        InetAddress,
  lmpTeLinkVerification     TruthValue,
  lmpTeLinkFaultManagement  TruthValue,
  lmpTeLinkDwdm             TruthValue,
  lmpTeLinkOperStatus       INTEGER,
  lmpTeLinkRowStatus        RowStatus,
  lmpTeLinkStorageType      StorageType
}

lmpTeLinkNbrNodeId OBJECT-TYPE
   SYNTAX        InetAddress (SIZE(4))
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This is the Node ID of the TE link remote node. This value
        may be learned during control channel parameter negotiation
        phase (in the Config message). Node ID address type must
        be IPv4."
   ::= { lmpTeLinkEntry 1 }

lmpTeLinkVerification OBJECT-TYPE
   SYNTAX        TruthValue
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object indicates if the extended LMP link verification
        procedure is enabled for this TE link."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,



Dubuc et al.             Expires November 2002                 [Page 39]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


        B. Rajagopalan, March 2002."
   ::= { lmpTeLinkEntry 2 }

lmpTeLinkFaultManagement OBJECT-TYPE
   SYNTAX        TruthValue
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object indicates if the extended LMP fault management
        procedure is enabled on this TE link."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   ::= { lmpTeLinkEntry 3 }

lmpTeLinkDwdm OBJECT-TYPE
   SYNTAX        TruthValue
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object indicates if the extended LMP DWDM procedure
        is enabled on this TE link."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   ::= { lmpTeLinkEntry 4 }

lmpTeLinkOperStatus OBJECT-TYPE
   SYNTAX        INTEGER { up(1), down(2), testing(3), init(4), degraded(5) }
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "The actual operational status of this TE link. The status
        is set to testing when the TE link is performing link
        verification. A degraded state indicates that there are
        no active control channel between the pair of nodes that
        form the endpoints of the TE link, but yet at least one
        data-bearing links on the TE link is allocated."
   ::= { lmpTeLinkEntry 5 }

lmpTeLinkRowStatus OBJECT-TYPE
   SYNTAX        RowStatus
   MAX-ACCESS    read-create
   STATUS        current



Dubuc et al.             Expires November 2002                 [Page 40]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   DESCRIPTION
       "This variable is used to create, modify, and/or
        delete a row in this table. All read-create objects
        can only be changed when lmpTeLinkRowStatus is active."
   ::= { lmpTeLinkEntry 6 }

lmpTeLinkStorageType OBJECT-TYPE
   SYNTAX        StorageType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The storage type for this conceptual row in the
        lmpTeLinkTable. Conceptual rows having the value
        'permanent' need not allow write-access to any
        columnar object in the row."
   ::= { lmpTeLinkEntry 7 }

-- End of lmpTeLinkTable


lmpLinkVerificationInterval OBJECT-TYPE
   SYNTAX        Unsigned32
   MAX-ACCESS    read-write
   STATUS        current
   DESCRIPTION
       "This object indicates how often the link verification procedure
        is executed. The interval is in milliseconds."
   ::= { lmpObjects 13 }


-- LMP Link Verification Table

lmpLinkVerificationTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF LmpLinkVerificationEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies TE link information associated with the
        LMP verification procedure."
   ::= { lmpObjects 14 }

lmpLinkVerificationEntry OBJECT-TYPE
   SYNTAX        LmpLinkVerificationEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table is created by a LMP-enabled device for
        every TE link that supports the LMP verification



Dubuc et al.             Expires November 2002                 [Page 41]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


        procedure."
   AUGMENTS      { lmpTeLinkEntry }
   ::= { lmpLinkVerificationTable 1 }

LmpLinkVerificationEntry ::= SEQUENCE {
  lmpVerifyInterval           LmpInterval,
  lmpVerifyDeadInterval       LmpInterval,
  lmpVerifyTransportMechanism BITS,
  lmpVerifyAllLinks           INTEGER,
  lmpTeLinkBitRate            Unsigned32,
  lmpTeLinkWavelength         Unsigned32
}

lmpVerifyInterval OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object specifies the VerifyInterval parameter used
        in the LMP link verification process. It indicates the interval
        at which the Test messages are sent."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   ::= { lmpLinkVerificationEntry 1 }

lmpVerifyDeadInterval OBJECT-TYPE
   SYNTAX        LmpInterval
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object specifies the VerifyDeadInterval parameter used
        in the verification of the physical connectivity of data-bearing
        links. It specifies the observation period used to detect a Test
        message at the remote node."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   ::= { lmpLinkVerificationEntry 2 }

lmpVerifyTransportMechanism OBJECT-TYPE
   SYNTAX        BITS {
                     -- SONET/SDH encoding type:
                     j016OverheadBytes(0),



Dubuc et al.             Expires November 2002                 [Page 42]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


                     j064OverheadBytes(1),
                     dccSectionOverheadBytes(2),
                     dccLineOverheadBytes(3),
                     pos(4),
                     j0Trace(5)
                     -- GigE encoding type: TBD
                     -- 10GigE encoding type: TBD
                 }
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This defines the transport mechanism for the Test messages. The
        scope of this bit mask is restricted to each link encoding
        type. The local node will set the bits corresponding to the
        various mechanisms it can support for transmitting LMP Test
        messages. The receiver chooses the appropriate mechanism in the
        BeginVerifyAck message."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   ::= { lmpLinkVerificationEntry 3 }

lmpVerifyAllLinks OBJECT-TYPE
   SYNTAX        INTEGER { verifyAllLinks(1), verifyNewLinks(2) }
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object indicates whether the verification process checks
        all entities or only the new entities that have been added to
        this TE link."
   ::= { lmpLinkVerificationEntry 4 }

lmpTeLinkBitRate OBJECT-TYPE
   SYNTAX        Unsigned32
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This is the bit rate at which the Test messages will be
        transmitted and is expressed in bytes per second."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   ::= { lmpLinkVerificationEntry 5 }




Dubuc et al.             Expires November 2002                 [Page 43]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


lmpTeLinkWavelength OBJECT-TYPE
   SYNTAX        Unsigned32
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This value corresponds to the wavelength at
        which the Test messages will be transmitted over and is
        measured in nanometers (nm). If each data-bearing link
        corresponds to a separate wavelength, than this value should be
        set to 0."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   ::= { lmpLinkVerificationEntry 6 }

-- End of lmpLinkVerificationTable


-- LMP TE Link Performance Table

lmpTeLinkPerfTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF LmpTeLinkPerfEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies LMP TE link performance counters."
   ::= { lmpObjects 15 }

lmpTeLinkPerfEntry OBJECT-TYPE
   SYNTAX        LmpTeLinkPerfEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table is created by a LMP-enabled device for
        every TE link."
   AUGMENTS      { lmpTeLinkEntry }
   ::= { lmpTeLinkPerfTable 1 }

LmpTeLinkPerfEntry ::= SEQUENCE {
  lmpTeLinkInOctets                       Counter32,
  lmpTeLinkOutOctets                      Counter32,
  lmpTeLinkBeginVerifyReceived            Counter32,
  lmpTeLinkBeginVerifySent                Counter32,
  lmpTeLinkBeginVerifyRetransmit          Counter32,
  lmpTeLinkBeginVerifyAckReceived         Counter32,
  lmpTeLinkBeginVerifyAckSent             Counter32,



Dubuc et al.             Expires November 2002                 [Page 44]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


  lmpTeLinkBeginVerifyNackReceived        Counter32,
  lmpTeLinkBeginVerifyNackSent            Counter32,
  lmpTeLinkEndVerifyReceived              Counter32,
  lmpTeLinkEndVerifySent                  Counter32,
  lmpTeLinkEndVerifyRetransmit            Counter32,
  lmpTeLinkEndVerifyAckReceived           Counter32,
  lmpTeLinkEndVerifyAckSent               Counter32,
  lmpTeLinkTestStatusSuccessReceived      Counter32,
  lmpTeLinkTestStatusSuccessSent          Counter32,
  lmpTeLinkTestStatusSuccessRetransmit    Counter32,
  lmpTeLinkTestStatusFailureReceived      Counter32,
  lmpTeLinkTestStatusFailureSent          Counter32,
  lmpTeLinkTestStatusFailureRetransmit    Counter32,
  lmpTeLinkTestStatusAckReceived          Counter32,
  lmpTeLinkTestStatusAckSent              Counter32,
  lmpTeLinkSummaryReceived                Counter32,
  lmpTeLinkSummarySent                    Counter32,
  lmpTeLinkSummaryRetransmit              Counter32,
  lmpTeLinkSummaryAckReceived             Counter32,
  lmpTeLinkSummaryAckSent                 Counter32,
  lmpTeLinkSummaryNackReceived            Counter32,
  lmpTeLinkSummaryNackSent                Counter32,
  lmpTeLinkChannelStatusReceived          Counter32,
  lmpTeLinkChannelStatusSent              Counter32,
  lmpTeLinkChannelStatusRetransmit        Counter32,
  lmpTeLinkChannelStatusAckReceived       Counter32,
  lmpTeLinkChannelStatusAckSent           Counter32,
  lmpTeLinkChannelStatusRequestReceived   Counter32,
  lmpTeLinkChannelStatusRequestSent       Counter32,
  lmpTeLinkChannelStatusRequestRetransmit Counter32,
  lmpTeLinkChannelStatusResponseSent      Counter32,
  lmpTeLinkChannelStatusResponseReceived  Counter32,
  lmpTeLinkCounterDiscontinuityTime       TimeStamp
}

lmpTeLinkInOctets OBJECT-TYPE
    SYNTAX      Counter32
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
            "The total number of LMP message octets received for
             this TE link."
    ::= { lmpTeLinkPerfEntry 1 }

lmpTeLinkOutOctets OBJECT-TYPE
    SYNTAX       Counter32
    MAX-ACCESS   read-only
    STATUS       current



Dubuc et al.             Expires November 2002                 [Page 45]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


    DESCRIPTION
            "The total number of LMP message octets transmitted out
             for this TE link."
    ::= { lmpTeLinkPerfEntry 2 }

lmpTeLinkBeginVerifyReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of BeginVerify messages that have
        been received for this TE link."
   ::= { lmpTeLinkPerfEntry 3 }

lmpTeLinkBeginVerifySent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of BeginVerify messages that have
        been sent for this TE link."
   ::= { lmpTeLinkPerfEntry 4 }

lmpTeLinkBeginVerifyRetransmit OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of BeginVerify messages that
        have been retransmitted for this TE link."
   ::= { lmpTeLinkPerfEntry 5 }

lmpTeLinkBeginVerifyAckReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of BeginVerifyAck messages that have
        been received for this TE link."
   ::= { lmpTeLinkPerfEntry 6 }

lmpTeLinkBeginVerifyAckSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of BeginVerifyAck messages that have
        been sent for this TE link."



Dubuc et al.             Expires November 2002                 [Page 46]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   ::= { lmpTeLinkPerfEntry 7 }

lmpTeLinkBeginVerifyNackReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of BeginVerifyNack messages that have
        been received for this TE link."
   ::= { lmpTeLinkPerfEntry 8 }

lmpTeLinkBeginVerifyNackSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of BeginVerifyNack messages that have
        been sent for this TE link."
   ::= { lmpTeLinkPerfEntry 9 }

lmpTeLinkEndVerifyReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of EndVerify messages that have
        been received for this TE link."
   ::= { lmpTeLinkPerfEntry 10 }

lmpTeLinkEndVerifySent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of EndVerify messages that have
        been sent for this TE link."
   ::= { lmpTeLinkPerfEntry 11 }

lmpTeLinkEndVerifyRetransmit OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of EndVerify messages that
        have been retransmitted over this control channel."
   ::= { lmpTeLinkPerfEntry 12 }

lmpTeLinkEndVerifyAckReceived OBJECT-TYPE



Dubuc et al.             Expires November 2002                 [Page 47]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of EndVerifyAck messages that have
        been received for this TE link."
   ::= { lmpTeLinkPerfEntry 13 }

lmpTeLinkEndVerifyAckSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of EndVerifyAck messages that have
        been sent for this TE link."
   ::= { lmpTeLinkPerfEntry 14 }

lmpTeLinkTestStatusSuccessReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of TestStatusSuccess messages that have
        been received for this TE link."
   ::= { lmpTeLinkPerfEntry 15 }

lmpTeLinkTestStatusSuccessSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of TestStatusSuccess messages that have
        been sent for this TE link."
   ::= { lmpTeLinkPerfEntry 16 }

lmpTeLinkTestStatusSuccessRetransmit OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of TestStatusSuccess messages that
        have been retransmitted for this TE link."
   ::= { lmpTeLinkPerfEntry 17 }

lmpTeLinkTestStatusFailureReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current



Dubuc et al.             Expires November 2002                 [Page 48]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   DESCRIPTION
       "This object counts the number of TestStatusFailure messages that have
        been received for this TE link."
   ::= { lmpTeLinkPerfEntry 18 }

lmpTeLinkTestStatusFailureSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of TestStatusFailure messages that have
        been sent for this TE link."
   ::= { lmpTeLinkPerfEntry 19 }

lmpTeLinkTestStatusFailureRetransmit OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of TestStatusFailure messages that
        have been retransmitted on this TE link."
   ::= { lmpTeLinkPerfEntry 20 }

lmpTeLinkTestStatusAckReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of TestStatusAck messages that have
        been received for this TE link."
   ::= { lmpTeLinkPerfEntry 21 }

lmpTeLinkTestStatusAckSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of TestStatusAck messages that have
        been sent for this TE link."
   ::= { lmpTeLinkPerfEntry 22 }

lmpTeLinkSummaryReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of LinkSummary messages that have
        been received for this TE link."



Dubuc et al.             Expires November 2002                 [Page 49]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   ::= { lmpTeLinkPerfEntry 23 }

lmpTeLinkSummarySent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of LinkSummary messages that have
        been sent for this TE link."
   ::= { lmpTeLinkPerfEntry 24 }

lmpTeLinkSummaryRetransmit OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of LinkSummary messages that
        have been retransmitted over this control channel."
   ::= { lmpTeLinkPerfEntry 25 }

lmpTeLinkSummaryAckReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of LinkSummaryAck messages that have
        been received for this TE link."
   ::= { lmpTeLinkPerfEntry 26 }

lmpTeLinkSummaryAckSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of LinkSummaryAck messages that have
        been sent for this TE link."
   ::= { lmpTeLinkPerfEntry 27 }

lmpTeLinkSummaryNackReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of LinkSummaryNack messages that have
        been received for this TE link."
   ::= { lmpTeLinkPerfEntry 28 }

lmpTeLinkSummaryNackSent OBJECT-TYPE



Dubuc et al.             Expires November 2002                 [Page 50]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of LinkSummaryNack messages that have
        been sent for this TE link."
   ::= { lmpTeLinkPerfEntry 29 }

lmpTeLinkChannelStatusReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatus messages that have
        been received for this TE link."
   ::= { lmpTeLinkPerfEntry 30 }

lmpTeLinkChannelStatusSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatus messages that have
        been sent for this TE link."
   ::= { lmpTeLinkPerfEntry 31 }

lmpTeLinkChannelStatusRetransmit OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatus messages that have
        been retransmitted for this TE link."
   ::= { lmpTeLinkPerfEntry 32 }

lmpTeLinkChannelStatusAckReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatusAck messages that have
        been received for this TE link."
   ::= { lmpTeLinkPerfEntry 33 }

lmpTeLinkChannelStatusAckSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current



Dubuc et al.             Expires November 2002                 [Page 51]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   DESCRIPTION
       "This object counts the number of ChannelStatus messages that have
        been sent for this TE link."
   ::= { lmpTeLinkPerfEntry 34 }

lmpTeLinkChannelStatusRequestReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatusRequest messages that
        have been received for this TE link."
   ::= { lmpTeLinkPerfEntry 35 }

lmpTeLinkChannelStatusRequestSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatusRequest messages that
        have been sent for this TE link."
   ::= { lmpTeLinkPerfEntry 36 }

lmpTeLinkChannelStatusRequestRetransmit OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatusRequest messages that
        have been retransmitted for this TE link."
   ::= { lmpTeLinkPerfEntry 37 }

lmpTeLinkChannelStatusResponseReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatusResponse messages that
        have been received for this TE link."
   ::= { lmpTeLinkPerfEntry 38 }

lmpTeLinkChannelStatusResponseSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of ChannelStatusResponse messages that
        have been sent for this TE link."



Dubuc et al.             Expires November 2002                 [Page 52]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   ::= { lmpTeLinkPerfEntry 39 }

lmpTeLinkCounterDiscontinuityTime OBJECT-TYPE
    SYNTAX       TimeStamp
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "The value of sysUpTime on the most recent occasion at which
         any one or more of this TE link's counters suffered a
         discontinuity. The relevant counters are the specific
         instances associated with this TE link of any Counter32
         object contained in the lmpTeLinkPerfTable. If
         no such discontinuities have occurred since the last re-
         initialization of the local management subsystem, then this
         object contains a zero value."
    ::= { lmpTeLinkPerfEntry 40 }

-- End of lmpTeLinkPerfTable


-- LMP Data Bearing Link Table

lmpDataBearingLinkTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF LmpDataBearingLinkEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies the data-bearing links managed by the
        LMP."
   ::= { lmpObjects 16 }

lmpDataBearingLinkEntry OBJECT-TYPE
   SYNTAX        LmpDataBearingLinkEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table exists for each ifEntry that represents
        a data-bearing link. An ifEntry with an ifIndex must exist
        before the corresponding lmpDataBearingLinkEntry is created.
        If an entry representing the data-bearing link is destroyed in
        the ifTable, then so is the corresponding entry in the
        lmpDataBearingLinkTable. The administrative status value is
        controlled from the ifEntry. The index to this table also
        used to get information in the dataBearingChannelTable
        [BUNDLE-MIB]."
   INDEX         { ifIndex }
   ::= { lmpDataBearingLinkTable 1 }




Dubuc et al.             Expires November 2002                 [Page 53]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


LmpDataBearingLinkEntry ::= SEQUENCE {
  lmpDataBearingLinkType               INTEGER,
  lmpDataBearingLinkIpAddrType         InetAddressType,
  lmpDataBearingLinkIpAddr             InetAddress,
  lmpDataBearingLinkRemoteIpAddress    InetAddress,
  lmpDataBearingLinkRemoteIfId         InterfaceIndexOrZero,
  lmpDataBearingLinkEncodingType       INTEGER,
  lmpDataBearingLinkActiveOperStatus   INTEGER,
  lmpDataBearingLinkPassiveOperStatus  INTEGER,
  lmpDataBearingLinkRowStatus          RowStatus,
  lmpDataBearingLinkStorageType        StorageType
}

lmpDataBearingLinkType OBJECT-TYPE
   SYNTAX        INTEGER {
                     port(1),
                     componentLink(2)
                 }
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This attribute specifies whether this data-bearing link is
        a port or a component link. Component link are multiplex
        capable whereas, ports are not multiplex capable."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   ::= { lmpDataBearingLinkEntry 1 }

lmpDataBearingLinkIpAddrType OBJECT-TYPE
   SYNTAX        InetAddressType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the data-bearing link IP address
        type. If the data-bearing link is unnumbered, the address
        type must be set to unknown(0)."
   ::= { lmpDataBearingLinkEntry 2 }

lmpDataBearingLinkIpAddr OBJECT-TYPE
   SYNTAX        InetAddress
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "IP address of the data-bearing link. This
        If the data-bearing link is unnumbered, then the



Dubuc et al.             Expires November 2002                 [Page 54]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


        IP address must be null."
   ::= { lmpDataBearingLinkEntry 3 }

lmpDataBearingLinkRemoteIpAddress OBJECT-TYPE
   SYNTAX        InetAddress
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "IP address of the remote end point. This
        information is either configured manually or is
        communicated by the remote node during the link verification
        procedure. If the data-bearing link is unnumbered, then the
        remote IP address must be null."
   ::= { lmpDataBearingLinkEntry 4 }

lmpDataBearingLinkRemoteIfId OBJECT-TYPE
   SYNTAX        InterfaceIndexOrZero
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "Interface identifier of the remote end point. This
        information is either configured manually or is
        communicated by the remote node during the link verification
        procedure."
   ::= { lmpDataBearingLinkEntry 5 }

lmpDataBearingLinkEncodingType OBJECT-TYPE
   SYNTAX        INTEGER {
                     packet(1),
                     ethernet(2),
                     ansiEtsiPdh(3),
                     sdhItuSonetAnsi(5),
                     digitalWrapper(7),
                     lambda(8),
                     fiber(9),
                     fiberChannel(11)
                 }
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The encoding type of the data-bearing link."
   REFERENCE
       "draft-ietf-mpls-generalized-signaling-08.txt - Generalized
        MPLS Signaling Functional Description, P. Ashwood-Smith,
        A. Banarjee, L. Berger, G. Bernstein, J. Drake, Y. Fan,
        E. Mannie, J. Lang, B. Rajagopalan, Y. Rekhter, D. Saha,
        V. Sharma, G. Swallow, Z. Tang, April 2002."
   ::= { lmpDataBearingLinkEntry 6 }



Dubuc et al.             Expires November 2002                 [Page 55]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


lmpDataBearingLinkActiveOperStatus OBJECT-TYPE
   SYNTAX        INTEGER {
                     upAlloc(1),
                     upFree(2),
                     down(3),
                     testing(4) }
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "The actual operational status of this data-bearing link
        (active FSM)."
   REFERENCE
       "draft-ietf-ccamp-lmp-03.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   ::= { lmpDataBearingLinkEntry 7 }

lmpDataBearingLinkPassiveOperStatus OBJECT-TYPE
   SYNTAX        INTEGER {
                     upAlloc(1),
                     upFree(2),
                     down(3),
                     psvTst(4) }
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "The actual operational status of this data-bearing link
        (passive FSM)."
   REFERENCE
       "draft-ietf-ccamp-lmp-02.txt - Link Management Protocol (LMP),
        J. Lang, K. Mitra, J. Drake, K. Kompella, Y. Rekhter,
        L. Berger, D. Saha, D. Basak, H. Sandick, A. Zinin,
        B. Rajagopalan, March 2002."
   ::= { lmpDataBearingLinkEntry 8 }

lmpDataBearingLinkRowStatus OBJECT-TYPE
   SYNTAX        RowStatus
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This variable is used to create, modify, and/or
        delete a row in this table. All read-create objects
        can only be changed when lmpDataBearingLinkRowStatus is active."
   ::= { lmpDataBearingLinkEntry 9 }

lmpDataBearingLinkStorageType OBJECT-TYPE
   SYNTAX        StorageType



Dubuc et al.             Expires November 2002                 [Page 56]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The storage type for this conceptual row in the
        lmpDataBearingLinkTable. Conceptual rows having the value
        'permanent' need not allow write-access to any
        columnar object in the row."
   ::= { lmpDataBearingLinkEntry 10 }

-- End of lmpDataBearingLinkTable


-- LMP Data Bearing Link Performance Table

lmpDataBearingLinkPerfTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF LmpDataBearingLinkPerfEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies the data-bearing links LMP performance
        counters."
   ::= { lmpObjects 17 }

lmpDataBearingLinkPerfEntry OBJECT-TYPE
   SYNTAX        LmpDataBearingLinkPerfEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table contains information about
        the LMP performance counters for the data-bearing links."
   AUGMENTS      { lmpDataBearingLinkEntry }
   ::= { lmpDataBearingLinkPerfTable 1 }

LmpDataBearingLinkPerfEntry ::= SEQUENCE {
  lmpDataBearingLinkTestReceived              Counter32,
  lmpDataBearingLinkTestSent                  Counter32,
  lmpDataBearingLinkActiveTestSuccess         Counter32,
  lmpDataBearingLinkActiveTestFailure         Counter32,
  lmpDataBearingLinkPassiveTestSuccess        Counter32,
  lmpDataBearingLinkPassiveTestFailure        Counter32,
  lmpDataBearingLinkCounterDiscontinuityTime  TimeStamp
}

lmpDataBearingLinkTestReceived OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION



Dubuc et al.             Expires November 2002                 [Page 57]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


       "This object counts the number of Test messages that have
        been received on this data-bearing link."
   ::= { lmpDataBearingLinkPerfEntry 1 }

lmpDataBearingLinkTestSent OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of Test messages that have
        been sent on this data-bearing link."
   ::= { lmpDataBearingLinkPerfEntry 2 }

lmpDataBearingLinkActiveTestSuccess OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of data-bearing link test
        that were successful on the active side of this data-
        bearing link."
   ::= { lmpDataBearingLinkPerfEntry 3 }

lmpDataBearingLinkActiveTestFailure OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of data-bearing link test
        that failed on the active side of this data-bearing link."
   ::= { lmpDataBearingLinkPerfEntry 4 }

lmpDataBearingLinkPassiveTestSuccess OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of data-bearing link test
        that were successful on the passive side of this data-
        bearing link."
   ::= { lmpDataBearingLinkPerfEntry 5 }

lmpDataBearingLinkPassiveTestFailure OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of data-bearing link test



Dubuc et al.             Expires November 2002                 [Page 58]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


        that failed on the passive side of this data-bearing link."
   ::= { lmpDataBearingLinkPerfEntry 6 }

lmpDataBearingLinkCounterDiscontinuityTime OBJECT-TYPE
    SYNTAX       TimeStamp
    MAX-ACCESS   read-only
    STATUS       current
    DESCRIPTION
        "The value of sysUpTime on the most recent occasion at which
         any one or more of this data-bearing link's counters suffered a
         discontinuity. The relevant counters are the specific
         instances associated with this data-bearing link of any Counter32
         object contained in the lmpDataBearingLinkPerfTable. If
         no such discontinuities have occurred since the last re-
         initialization of the local management subsystem, then this
         object contains a zero value."
    ::= { lmpDataBearingLinkPerfEntry 7 }

-- End of lmpDataBearingLinkPerfTable


-- Notification Configuration

lmpLinkPropertyMismatchNotifEnable OBJECT-TYPE
   SYNTAX        TruthValue
   MAX-ACCESS    read-write
   STATUS        current
   DESCRIPTION
       "If this object is true, then it enables the
        generation of lmpTeLinkPropertyMismatch
        and lmpDataBearingLinkPropertyMismatch notifications,
        otherwise these notifications are not emitted."
   DEFVAL        { false }
   ::= { lmpObjects 18 }

lmpUnprotectedNotifEnable OBJECT-TYPE
   SYNTAX        TruthValue
   MAX-ACCESS    read-write
   STATUS        current
   DESCRIPTION
       "If this object is true, then it enables the
        generation of lmpUnprotected notifications,
        otherwise these notifications are not emitted."
   DEFVAL        { false }
   ::= { lmpObjects 19 }

lmpCcUpDownNotifEnable OBJECT-TYPE
   SYNTAX        TruthValue



Dubuc et al.             Expires November 2002                 [Page 59]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   MAX-ACCESS    read-write
   STATUS        current
   DESCRIPTION
       "If this object is true, then it enables the generation of
        lmpControlChannelUp and lmpControlChannelDown notifications,
        otherwise these notifications are not emitted."
   DEFVAL        { false }
   ::= { lmpObjects 20 }

lmpTeLinkNotifEnable OBJECT-TYPE
   SYNTAX        TruthValue
   MAX-ACCESS    read-write
   STATUS        current
   DESCRIPTION
       "If this object is true, then it enables the
        generation of lmpTeLinkDegraded and lmpTeLinkNotDegraded
        notifications, otherwise these notifications are not emitted."
   DEFVAL        { false }
   ::= { lmpObjects 21 }

lmpDataBearingLinkNotifEnable OBJECT-TYPE
   SYNTAX        TruthValue
   MAX-ACCESS    read-write
   STATUS        current
   DESCRIPTION
       "If this object is true, then it enables the
        generation of lmpDataBearingLinkVerificationFailure
        notification, otherwise these notifications are not emitted."
   DEFVAL        { false }
   ::= { lmpObjects 22 }


-- Notifications

-- Link Property Mismatch Notifications

lmpTeLinkPropertyMismatch NOTIFICATION-TYPE
   OBJECTS       { teLinkRemoteIpAddr,
                   teLinkIncomingIfId }
   STATUS        current
   DESCRIPTION
       "This notification is generated when a TE link property
        mismatch is detected on the node. The received remote TE link
        id of the misconfigured TE link is represented by either
        teLinkRemoteIpAddr or teLinkIncomingIfId depending on whether
        the TE link is numbered or unnumbered. This notification should
        not be sent unless lmpLinkPropertyMismatchNotifEnable is
        true."



Dubuc et al.             Expires November 2002                 [Page 60]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   ::= { lmpNotifications 1 }

lmpDataBearingLinkPropertyMismatch NOTIFICATION-TYPE
   OBJECTS       { ifIndex,
                   lmpDataBearingLinkRemoteIfId }
   STATUS        current
   DESCRIPTION
       "This notification is generated when a data-bearing link
        property mismatch is detected on the node. ifIndex
        is the interface index of the TE link. The remote entity
        interface id is the remote entity interface id received in the
        LinkSummary message. This notification should
        not be sent unless lmpLinkPropertyMismatchNotifEnable is
        true."
   ::= { lmpNotifications 2 }

-- Neighbor Notification

lmpUnprotected NOTIFICATION-TYPE
   OBJECTS       { lmpCcNbrNodeId }
   STATUS        current
   DESCRIPTION
       "This notification is generated when there are more than one
        control channels between LMP neighbors and the last redundant
        control channel has failed. If the remaining operational control
        channel fails, then there will be no more control channels
        between the pair of nodes and all the TE links between the pair
        of nodes will go to degraded state. This notification should not
        be sent unless lmpUnprotectedNotifEnable is set to true."
   ::= { lmpNotifications 3 }

-- Control Channel Notifications

lmpControlChannelUp NOTIFICATION-TYPE
   OBJECTS       { lmpCcAdminStatus, lmpCcOperStatus }
   STATUS        current
   DESCRIPTION
       "This notification is generated when a control
        channel transitions to the up operational state. This
        notification should not be sent unless lmpCcUpDownNotifEnable
        is true."
   ::= { lmpNotifications 4 }

lmpControlChannelDown NOTIFICATION-TYPE
   OBJECTS       { lmpCcAdminStatus, lmpCcOperStatus }
   STATUS        current
   DESCRIPTION
       "This notification is generated when a control



Dubuc et al.             Expires November 2002                 [Page 61]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


        channel transitions out of the up operational state. This
        notification should not be sent unless lmpCcUpDownNotifEnable
        is true."
   ::= { lmpNotifications 5 }

-- TE Link Notification

lmpTeLinkDegraded NOTIFICATION-TYPE
   OBJECTS       { ifIndex }
   STATUS        current
   DESCRIPTION
       "This notification is generated when a lmpTeLinkOperStatus
        object for a TE link enters the degraded state. This
        notification should not be sent unless lmpTeLinkNotifEnable
        is true."
   ::= { lmpNotifications 6 }

lmpTeLinkNotDegraded NOTIFICATION-TYPE
   OBJECTS       { ifIndex }
   STATUS        current
   DESCRIPTION
       "This notification is generated when a lmpTeLinkOperStatus
        object for a TE link leaves the degraded state. This
        notification should not be sent unless lmpTeLinkNotifEnable
        is true."
   ::= { lmpNotifications 7 }

-- Data-bearing Link Notification

lmpDataBearingLinkVerificationFailure NOTIFICATION-TYPE
   OBJECTS       { ifIndex }
   STATUS        current
   DESCRIPTION
       "This notification is generated when a data-bearing
        link verification fails. This notification should not be sent
        unless lmpDataBearingLinkNotifEnable is true."
   ::= { lmpNotifications 8 }

-- End of notifications


-- Module compliance

lmpGroups
   OBJECT IDENTIFIER ::= { lmpConformance 1 }

lmpCompliances
   OBJECT IDENTIFIER ::= { lmpConformance 2 }



Dubuc et al.             Expires November 2002                 [Page 62]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


lmpFullModuleCompliance MODULE-COMPLIANCE
   STATUS current
   DESCRIPTION
       "Compliance statement for agents that support the
        configuration and monitoring of LMP MIB."
   MODULE -- this module

      -- The mandatory groups have to be implemented
      -- by all LMP-enabled devices. However, they may all be supported
      -- as read-only objects in the case where manual
      -- configuration is unsupported.

      MANDATORY-GROUPS    { lmpNodeGroup,
                            lmpControlChannelGroup,
                            lmpLinkPropertyCorrelationGroup,
                            lmpPerfGroup,
                            lmpTeLinkGroup,
                            lmpDataBearingLinkGroup }

      GROUP lmpControlChannelIsNotInterfaceGroup
      DESCRIPTION
          "This group is mandatory for devices which support
           control channels that are not interfaces, in addition to
           lmpControlChannelGroup. The following constraints apply:
           lmpCcIsIf must at least be read-only returning false(1)."

      GROUP lmpControlChannelIsInterfaceGroup
      DESCRIPTION
          "This group is mandatory for devices which support
           control channels that are interfaces, in addition to
           lmpControlChannelGroup. The following constraints apply:
           lmpCcIsIf must at least be read-only returning true(2)."

      GROUP lmpLinkVerificationGroup
      DESCRIPTION
          "This group is mandatory for devices which support
           the link verification procedure."

      GROUP lmpNotificationGroup
      DESCRIPTION
          "This group is optional."

      -- lmpNbrTable

      OBJECT      lmpNbrRowStatus
      SYNTAX      INTEGER { active(1), notInService(2),
                            createAndGo(4), destroy(6) }
      MIN-ACCESS  read-only



Dubuc et al.             Expires November 2002                 [Page 63]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


      DESCRIPTION
          "The notReady(3) and createAndWait(5) states need
           not be supported."

      OBJECT      lmpNbrStorageType
      SYNTAX      INTEGER { other(1) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Only other(1) needs to be supported."

      -- lmpControlChannelTable

      OBJECT      lmpRemoteCcIpAddrType
      SYNTAX      InetAddressType { unknown(0), ipv4(1), ipv6(2) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "The dns(16) adress type needs not be supported. For
           point-to-point configuration, this object MIN-ACCESS
           is read-create."

      OBJECT      lmpRemoteCcIpAddr
      SYNTAX      InetAddress (SIZE(0|4|16))
      MIN-ACCESS  read-only
      DESCRIPTION
          "The size of the IP address depends on the address type.
           For point-to-point configuration, this object MIN-ACCESS is
           read-create."

      OBJECT      lmpCcRowStatus
      SYNTAX      INTEGER { active(1), notInService(2),
                            createAndGo(4), destroy(6) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "The notReady(3) and createAndWait(5) states need
           not be supported."

      OBJECT      lmpCcOperStatus
      SYNTAX      INTEGER { up(1), down(2) }
      DESCRIPTION
          "A value of active(3), configuring(4), goingDown(5)
           need not be supported."

      OBJECT      lmpCcStorageType
      SYNTAX      INTEGER { other(1) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Only other(1) needs to be supported."




Dubuc et al.             Expires November 2002                 [Page 64]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


      -- lmpTeLinkTable

      OBJECT      lmpTeLinkOperStatus
      SYNTAX      INTEGER { up(1), down(2), degraded(4) }
      DESCRIPTION
          "The testing(3) state need not be supported."

      OBJECT      lmpTeLinkRowStatus
      SYNTAX      INTEGER { active(1), notInService(2),
                            createAndGo(4), destroy(6) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "The notReady(3) and createAndWait(5) states need
           not be supported."

      OBJECT      lmpTeLinkStorageType
      SYNTAX      INTEGER { other(1) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Only other(1) needs to be supported."

      -- lmpDataBearingLinkTable

      OBJECT      lmpDataBearingLinkActiveOperStatus
      SYNTAX      INTEGER { up(1), down(2), degraded(4) }
      DESCRIPTION
          "A value of testing(3) need not be supported."

      OBJECT      lmpDataBearingLinkPassiveOperStatus
      SYNTAX      INTEGER { up(1), down(2), degraded(4) }
      DESCRIPTION
          "A value of testing(3) need not be supported."

      OBJECT      lmpDataBearingLinkRowStatus
      SYNTAX      INTEGER { active(1), notInService(2),
                            createAndGo(4), destroy(6) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "The notReady(3) and createAndWait(5) states need
           not be supported."

      OBJECT      lmpDataBearingLinkStorageType
      SYNTAX      INTEGER { other(1) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Only other(1) needs to be supported."

   ::= { lmpCompliances 1 }



Dubuc et al.             Expires November 2002                 [Page 65]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


lmpMonitoringModuleCompliance MODULE-COMPLIANCE
   STATUS current
   DESCRIPTION
       "Compliance statement for agents that support the
        monitoring of the LMP MIB."
   MODULE -- this module

      -- The mandatory groups have to be implemented
      -- by all LMP-enabled devices. However, they may all be supported
      -- as read-only objects in the case where manual
      -- configuration is unsupported.

      MANDATORY-GROUPS    { lmpNodeGroup,
                            lmpControlChannelGroup,
                            lmpLinkPropertyCorrelationGroup,
                            lmpPerfGroup,
                            lmpTeLinkGroup,
                            lmpDataBearingLinkGroup }

      GROUP lmpControlChannelIsNotInterfaceGroup
      DESCRIPTION
          "This group is mandatory for devices which support
           control channels that are not interfaces, in addition to
           lmpControlChannelGroup. The following constraints apply:
           lmpCcIsIf must at least be read-only returning false(1)."

      GROUP lmpControlChannelIsInterfaceGroup
      DESCRIPTION
          "This group is mandatory for devices which support
           control channels that are interfaces, in addition to
           lmpControlChannelGroup. The following constraints apply:
           lmpCcIsIf must at least be read-only returning true(2)."

      GROUP lmpLinkVerificationGroup
      DESCRIPTION
          "This group is mandatory for devices which support
           the link verification procedure."

      GROUP lmpNotificationGroup
      DESCRIPTION
          "This group is optional."

      -- Scalars

      OBJECT      lmpAdminStatus
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."



Dubuc et al.             Expires November 2002                 [Page 66]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


      OBJECT      lmpLinkVerificationInterval
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcHelloIntervalDefault
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcHelloIntervalDefaultMin
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcHelloIntervalDefaultMax
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcHelloDeadIntervalDefault
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcHelloDeadIntervalDefaultMin
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcHelloDeadIntervalDefaultMax
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      -- lmpNbrTable

      OBJECT      lmpNbrRetransmitInterval
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpNbrRetransmitTimeout
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpNbrRowStatus



Dubuc et al.             Expires November 2002                 [Page 67]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


      SYNTAX      INTEGER { active(1), notInService(2),
                            createAndGo(4), destroy(6) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "The notReady(3) and createAndWait(5) states need
           not be supported."

      OBJECT      lmpNbrStorageType
      SYNTAX      INTEGER { other(1) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Only other(1) needs to be supported."

      -- lmpControlChannelTable

      OBJECT      lmpCcUnderlyingIfIndex
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcIsIf
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcNbrNodeId
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpRemoteCcIpAddrType
      SYNTAX      InetAddressType { unknown(0), ipv4(1), ipv6(2) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "The dns(16) adress type needs not be supported."

      OBJECT      lmpRemoteCcIpAddr
      SYNTAX      InetAddress (SIZE(0|4|16))
      MIN-ACCESS  read-only
      DESCRIPTION
          "The size of the IP address depends on the address type."

      OBJECT      lmpCcSetupRole
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcAuthentication



Dubuc et al.             Expires November 2002                 [Page 68]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcConfigRetransmitInterval
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcConfigRetransmitTimeout
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcHelloIntervalMin
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcHelloIntervalMax
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcHelloDeadIntervalMin
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcHelloDeadIntervalMax
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpCcRowStatus
      SYNTAX      INTEGER { active(1), notInService(2),
                            createAndGo(4), destroy(6) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "The notReady(3) and createAndWait(5) states need
           not be supported."

      OBJECT      lmpCcOperStatus
      SYNTAX      INTEGER { up(1), down(2) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "A value of active(3), configuring(4), goingDown(5)
           need not be supported."



Dubuc et al.             Expires November 2002                 [Page 69]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


      OBJECT      lmpCcStorageType
      SYNTAX      INTEGER { other(1) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Only other(1) needs to be supported."

      -- lmpLinkVerificationTable

      OBJECT      lmpVerifyInterval
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpVerifyDeadInterval
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpVerifyAllLinks
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      -- lmpTeLinkTable

      OBJECT      lmpTeLinkNbrNodeId
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required if the link verification
           procedure is enabled."

      OBJECT      lmpTeLinkVerification
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpTeLinkFaultManagement
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpTeLinkDwdm
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpTeLinkOperStatus
      SYNTAX      INTEGER { up(1), down(2), degraded(4) }



Dubuc et al.             Expires November 2002                 [Page 70]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


      MIN-ACCESS  read-only
      DESCRIPTION
          "The testing(3) state need not be supported."

      OBJECT      lmpTeLinkRowStatus
      SYNTAX      INTEGER { active(1), notInService(2),
                            createAndGo(4), destroy(6) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "The notReady(3) and createAndWait(5) states need
           not be supported."

      OBJECT      lmpTeLinkStorageType
      SYNTAX      INTEGER { other(1) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Only other(1) needs to be supported."

      -- lmpTeLinkVerificationTable

      OBJECT      lmpTeLinkBitRate
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpTeLinkWavelength
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      -- lmpDataBearingLinkTable

      OBJECT      lmpDataBearingLinkIpAddrType
      SYNTAX      InetAddressType { unknown(0), ipv4(1), ipv6(2) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "The dns(16) address type need not be supported.
           The ipv4(1) and ipv6(2) address types need not be
           supported if numbered links are not supported. The
           unknown(0) address type needs not be supported if
           unnumbered links are not supported."

      OBJECT      lmpDataBearingLinkIpAddr
      SYNTAX      InetAddress (SIZE(0|4|16))
      MIN-ACCESS  read-only
      DESCRIPTION
          "Size of data-bearing link IP address depends on type
           of data-bearing link. Data-bearing link IP address size



Dubuc et al.             Expires November 2002                 [Page 71]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


           is zero if link is unnumbered, four if link IP address is
           IPv4 and sixteen if link IP address is IPv6."

      OBJECT      lmpDataBearingLinkRemoteIpAddress
      SYNTAX      InetAddress (SIZE(0|4|16))
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required if the link verification
           procedure is enabled."

      OBJECT      lmpDataBearingLinkRemoteIfId
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required if the link verification
           procedure is enabled."

      OBJECT      lmpDataBearingLinkEncodingType
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."

      OBJECT      lmpDataBearingLinkActiveOperStatus
      SYNTAX      INTEGER { up(1), down(2), degraded(4) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "A value of testing(3) need not be supported."

      OBJECT      lmpDataBearingLinkPassiveOperStatus
      SYNTAX      INTEGER { up(1), down(2), degraded(4) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "A value of psvTst(3) need not be supported."

      OBJECT      lmpDataBearingLinkRowStatus
      SYNTAX      INTEGER { active(1), notInService(2),
                            createAndGo(4), destroy(6) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "The notReady(3) and createAndWait(5) states need
           not be supported."

      OBJECT      lmpDataBearingLinkStorageType
      SYNTAX      INTEGER { other(1) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Only other(1) needs to be supported."

   ::= { lmpCompliances 2 }



Dubuc et al.             Expires November 2002                 [Page 72]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


-- Units of conformance

lmpNodeGroup OBJECT-GROUP
   OBJECTS { lmpAdminStatus,
             lmpOperStatus,
             lmpNbrAdminStatus,
             lmpNbrOperStatus,
             lmpNbrRowStatus,
             lmpNbrStorageType,
             lmpUnprotectedNotifEnable
           }
   STATUS  current
   DESCRIPTION
          "Collection of objects needed for LMP node configuration."
   ::= { lmpGroups 1 }

lmpControlChannelGroup OBJECT-GROUP
   OBJECTS {
             lmpNbrRetransmitInterval,
             lmpNbrRetransmitTimeout,
             lmpNbrAdminStatus,
             lmpNbrOperStatus,
             lmpNbrRowStatus,
             lmpNbrStorageType,
             lmpCcHelloIntervalDefault,
             lmpCcHelloIntervalDefaultMin,
             lmpCcHelloIntervalDefaultMax,
             lmpCcHelloDeadIntervalDefault,
             lmpCcHelloDeadIntervalDefaultMin,
             lmpCcHelloDeadIntervalDefaultMax,
             lmpCcNbrNodeId,
             lmpRemoteCcId,
             lmpRemoteCcIpAddrType,
             lmpRemoteCcIpAddr,
             lmpCcSetupRole,
             lmpCcAuthentication,
             lmpCcConfigRetransmitInterval,
             lmpCcConfigRetransmitTimeout,
             lmpCcHelloInterval,
             lmpCcHelloIntervalMin,
             lmpCcHelloIntervalMax,
             lmpCcHelloIntervalNegotiated,
             lmpCcHelloDeadInterval,
             lmpCcHelloDeadIntervalMin,
             lmpCcHelloDeadIntervalMax,
             lmpCcHelloDeadIntervalNegotiated,
             lmpCcOperStatus,
             lmpCcRowStatus,



Dubuc et al.             Expires November 2002                 [Page 73]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


             lmpCcStorageType,
             lmpCcUpDownNotifEnable
           }
   STATUS  current
   DESCRIPTION
          "Collection of objects needed for LMP interface
           configuration."
   ::= { lmpGroups 2 }

lmpControlChannelIsInterfaceGroup OBJECT-GROUP
   OBJECTS { lmpCcIsIf }
   STATUS  current
   DESCRIPTION
          "Objects needed to implement control channels that are
           interfaces."
   ::= { lmpGroups 3 }

lmpControlChannelIsNotInterfaceGroup OBJECT-GROUP
   OBJECTS {
             lmpCcUnderlyingIfIndex,
             lmpCcIsIf,
             lmpCcLastChange,
             lmpCcAdminStatus
           }
   STATUS  current
   DESCRIPTION
          "Objects needed to implement control channels that are not
           interfaces."
   ::= { lmpGroups 4 }

lmpLinkPropertyCorrelationGroup OBJECT-GROUP
   OBJECTS { lmpLinkPropertyMismatchNotifEnable }
   STATUS  current
   DESCRIPTION
          "Collection of objects needed to implement the link
           property correlation procedure."
   ::= { lmpGroups 5 }

lmpLinkVerificationGroup OBJECT-GROUP
   OBJECTS { lmpLinkVerificationInterval,
             lmpVerifyInterval,
             lmpVerifyDeadInterval,
             lmpVerifyTransportMechanism,
             lmpVerifyAllLinks,
             lmpTeLinkBitRate,
             lmpTeLinkWavelength,
             lmpDataBearingLinkNotifEnable
           }



Dubuc et al.             Expires November 2002                 [Page 74]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   STATUS  current
   DESCRIPTION
          "Collection of objects needed to implement the link
           verification procedure."
   ::= { lmpGroups 6 }

lmpPerfGroup OBJECT-GROUP
   OBJECTS { lmpCcInOctets,
             lmpCcInDiscards,
             lmpCcInErrors,
             lmpCcOutOctets,
             lmpCcOutDiscards,
             lmpCcOutErrors,
             lmpCcConfigReceived,
             lmpCcConfigSent,
             lmpCcConfigRetransmit,
             lmpCcConfigAckReceived,
             lmpCcConfigAckSent,
             lmpCcConfigNackSent,
             lmpCcConfigNackReceived,
             lmpCcHelloReceived,
             lmpCcHelloSent,
             lmpCcBeginVerifyReceived,
             lmpCcBeginVerifySent,
             lmpCcBeginVerifyRetransmit,
             lmpCcBeginVerifyAckReceived,
             lmpCcBeginVerifyAckSent,
             lmpCcBeginVerifyNackReceived,
             lmpCcBeginVerifyNackSent,
             lmpCcEndVerifyReceived,
             lmpCcEndVerifySent,
             lmpCcEndVerifyRetransmit,
             lmpCcEndVerifyAckReceived,
             lmpCcEndVerifyAckSent,
             lmpCcTestStatusSuccessReceived,
             lmpCcTestStatusSuccessSent,
             lmpCcTestStatusSuccessRetransmit,
             lmpCcTestStatusFailureReceived,
             lmpCcTestStatusFailureSent,
             lmpCcTestStatusFailureRetransmit,
             lmpCcTestStatusAckReceived,
             lmpCcTestStatusAckSent,
             lmpCcLinkSummaryReceived,
             lmpCcLinkSummarySent,
             lmpCcLinkSummaryRetransmit,
             lmpCcLinkSummaryAckReceived,
             lmpCcLinkSummaryAckSent,
             lmpCcLinkSummaryNackReceived,



Dubuc et al.             Expires November 2002                 [Page 75]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


             lmpCcLinkSummaryNackSent,
             lmpCcChannelStatusReceived,
             lmpCcChannelStatusSent,
             lmpCcChannelStatusRetransmit,
             lmpCcChannelStatusAckReceived,
             lmpCcChannelStatusAckSent,
             lmpCcChannelStatusRequestReceived,
             lmpCcChannelStatusRequestSent,
             lmpCcChannelStatusRequestRetransmit,
             lmpCcChannelStatusResponseReceived,
             lmpCcChannelStatusResponseSent,
             lmpCcCounterDiscontinuityTime,
             lmpTeLinkInOctets,
             lmpTeLinkOutOctets,
             lmpTeLinkBeginVerifyReceived,
             lmpTeLinkBeginVerifySent,
             lmpTeLinkBeginVerifyRetransmit,
             lmpTeLinkBeginVerifyAckReceived,
             lmpTeLinkBeginVerifyAckSent,
             lmpTeLinkBeginVerifyNackReceived,
             lmpTeLinkBeginVerifyNackSent,
             lmpTeLinkEndVerifyReceived,
             lmpTeLinkEndVerifySent,
             lmpTeLinkEndVerifyRetransmit,
             lmpTeLinkEndVerifyAckReceived,
             lmpTeLinkEndVerifyAckSent,
             lmpTeLinkTestStatusSuccessReceived,
             lmpTeLinkTestStatusSuccessSent,
             lmpTeLinkTestStatusSuccessRetransmit,
             lmpTeLinkTestStatusFailureReceived,
             lmpTeLinkTestStatusFailureSent,
             lmpTeLinkTestStatusFailureRetransmit,
             lmpTeLinkTestStatusAckReceived,
             lmpTeLinkTestStatusAckSent,
             lmpTeLinkSummaryReceived,
             lmpTeLinkSummarySent,
             lmpTeLinkSummaryRetransmit,
             lmpTeLinkSummaryAckReceived,
             lmpTeLinkSummaryAckSent,
             lmpTeLinkSummaryNackReceived,
             lmpTeLinkSummaryNackSent,
             lmpTeLinkChannelStatusReceived,
             lmpTeLinkChannelStatusSent,
             lmpTeLinkChannelStatusRetransmit,
             lmpTeLinkChannelStatusAckReceived,
             lmpTeLinkChannelStatusAckSent,
             lmpTeLinkChannelStatusRequestReceived,
             lmpTeLinkChannelStatusRequestSent,



Dubuc et al.             Expires November 2002                 [Page 76]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


             lmpTeLinkChannelStatusRequestRetransmit,
             lmpTeLinkChannelStatusResponseSent,
             lmpTeLinkChannelStatusResponseReceived,
             lmpTeLinkCounterDiscontinuityTime,
             lmpDataBearingLinkTestReceived,
             lmpDataBearingLinkTestSent,
             lmpDataBearingLinkActiveTestSuccess,
             lmpDataBearingLinkActiveTestFailure,
             lmpDataBearingLinkPassiveTestSuccess,
             lmpDataBearingLinkPassiveTestFailure,
             lmpDataBearingLinkCounterDiscontinuityTime
           }
   STATUS  current
   DESCRIPTION
          "Collection of objects needed for providing performance
           information about LMP interfaces and data-bearing links."
   ::= { lmpGroups 7 }

lmpTeLinkGroup OBJECT-GROUP
   OBJECTS { lmpTeLinkNbrNodeId,
             lmpTeLinkVerification,
             lmpTeLinkFaultManagement,
             lmpTeLinkDwdm,
             lmpTeLinkOperStatus,
             lmpTeLinkRowStatus,
             lmpTeLinkStorageType,
             lmpTeLinkNotifEnable
           }
   STATUS  current
   DESCRIPTION
          "Collection of objects needed for TE link configuration."
   ::= { lmpGroups 8 }

lmpDataBearingLinkGroup OBJECT-GROUP
   OBJECTS { lmpDataBearingLinkType,
             lmpDataBearingLinkIpAddrType,
             lmpDataBearingLinkIpAddr,
             lmpDataBearingLinkRemoteIpAddress,
             lmpDataBearingLinkRemoteIfId,
             lmpDataBearingLinkEncodingType,
             lmpDataBearingLinkActiveOperStatus,
             lmpDataBearingLinkPassiveOperStatus,
             lmpDataBearingLinkRowStatus,
             lmpDataBearingLinkStorageType
           }
   STATUS  current
   DESCRIPTION
          "Collection of objects needed for data-bearing link



Dubuc et al.             Expires November 2002                 [Page 77]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


           configuration."
   ::= { lmpGroups 9 }

lmpNotificationGroup NOTIFICATION-GROUP
   NOTIFICATIONS { lmpTeLinkPropertyMismatch,
                   lmpDataBearingLinkPropertyMismatch,
                   lmpUnprotected,
                   lmpControlChannelUp,
                   lmpControlChannelDown,
                   lmpTeLinkDegraded,
                   lmpTeLinkNotDegraded,
                   lmpDataBearingLinkVerificationFailure }
   STATUS  current
   DESCRIPTION
          "Set of notifications implemented in this module.
           None is mandatory."
   ::= { lmpGroups 10 }

-- End of LMP-MIB
END


11.  Security Considerations

   It is clear that this MIB is potentially useful for monitoring of LMP
   enabled devices. This MIB can also be used for configuration of cer-
   tain objects, and anything that can be configured can be incorrectly
   configured, with potentially disastrous results.

   At this writing, no security holes have been identified beyond those
   that SNMP Security [RFC2571] is itself intended to address.  These
   relate to primarily controlled access to sensitive information and
   the ability to configure a device - or which might result from opera-
   tor error, which is beyond the scope of any security architecture.

   There are a number of management objects defined in this MIB which
   have a MAX-ACCESS clause of read-write and/or read-create. Such
   objects may be considered sensitive or vulnerable in some network
   environments. The support for SET operations in a non-secure environ-
   ment without proper protection can have a negative effect on network
   operations. The use of SNMP Version 3 is recommended over prior ver-
   sions, for configuration control, as its security model is improved.

   SNMPv1 or SNMPv2 are by themselves not a secure environment. Even if
   the network itself is secure (for example by using IPSec [IPSEC]),
   there is no control as to who on the secure network is allowed to
   access and GET/SET (read/change/create/delete) the objects in this
   MIB. It is recommended that the implementers consider the security



Dubuc et al.             Expires November 2002                 [Page 78]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   features as provided by the SNMPv3 framework. Specifically, the use
   of the User-based Security Model [RFC2574] and the View-based Access
   Control [RFC2575] is recommended. It is then a customer/user respon-
   sibility to ensure that the SNMP entity giving access to an instance
   of this MIB is properly configured to give access to the objects only
   to those principals (users) that have legitimate rights to indeed GET
   or SET (change/create/delete) them.

   There are a number of managed objects in this MIB that may contain
   information that may be sensitive from a business perspective, in
   that they can be used to derive the network topology, e.g. list of
   nodes and their IP address (lmpNbrTable) and list of data-bearing
   links (lmpDataBearingLinkTable). Allowing uncontrolled access to
   these objects could result in malicious and unwanted disruptions of
   network traffic, incorrect network configurations or theft of com-
   petitive business information. There are no objects that are particu-
   larly sensitive in their own right, such as passwords or monetary
   amounts.


12.  Acknowledgments

   The general structure of this draft has been modeled around draft-
   ietf-mpls-lsr-mib-06.txt.

   The authors wish to thank Dmitry Ryumkin, Baktha Muralidharan and
   George Wang.


13.  References

   [LMP]         Lang, J., Mitra, K., Drake, J., Kompella, K.,
                 Rekhter, Y., Berger, L., Saha, S., Basak, D.,
                 Sandick, H., Zinin, A., and Rajagopalan, B.,
                 "Link Management Protocol", Internet Draft
                 <draft-ietf-ccamp-lmp-03.txt>, March 2002.

   [GMPLS]       Ashwood-Smith, P., Banarjee, A., Berger, L.,
                 Bernstein, G., Drake, J., Fan, Y., Kompella, K.,
                 Mannie, E., Lang, J., Rajagopalan, B., Rekhter, Y.,
                 Saha, D., Sharma, V., Swallow, G., and Tang, Z.,
                 "Generalized MPLS Signaling Function Description",
                 Internet Draft
                 <draft-ietf-mpls-generalized-signaling-08.txt>,
                 April 2002.

   [BUNDLE]      Kompella, K., Rekhter, Y., and Berger, L.,
                 "Link Bundling in MPLS Traffic Engineering",



Dubuc et al.             Expires November 2002                 [Page 79]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


                 Internet Draft <draft-ietf-mpls-bundle-03.txt>,
                 May 2002.

   [BUNDLE-MIB]  Dubuc, M., Dharanikota, S. Nadeau, T., Lang, J.,
                 "Link Bundling Management Information Base",
                 Internet Draft <draft-ietf-mpls-bundle-mib-02.txt>,
                 May 2002.

   [Assigned]    Reynolds, J., and J. Postel, "Assigned Numbers",
                 RFC 1700, October 1994. See also:
                 http://www.isi.edu/in-notes/iana/assignments/smi-
                 numbers

   [IANAFamily]  Internet Assigned Numbers Authority (IANA), ADDRESS
                 FAMILY NUMBERS, (http://www.isi.edu/in-
                 notes/iana/assignements/address-family-numbers),
                 for MIB see:
                 ftp://ftp.isi.edu/mib/ianaaddressfamilynumbers.mib

   [RFC2571]     Harrington, D., Presuhn, R., and B. Wijnen, "An
                 Architecture for Describing SNMP Management
                 Frameworks", RFC 2571, April 1999.

   [RFC1155]     Rose, M., and K. McCloghrie, "Structure and
                 Identification of Management Information for TCP/IP-
                 based Internets", STD 16, RFC 1155, May 1990.

   [RFC1212]     Rose, M., and K. McCloghrie, "Concise MIB Definitions",
                 STD 16, RFC 1212, March 1991.

   [RFC1215]     M. Rose, "A Convention for Defining Traps for use with
                 the SNMP", RFC 1215, March 1991.

   [RFC2578]     McCloghrie, K., Perkins, D., Schoenwaelder, J., Case,
                 J., Rose, M., and S. Waldbusser, "Structure of
                 Management Information Version 2 (SMIv2)", STD 58,
                 RFC 2578, April 1999.

   [RFC2579]     McCloghrie, K., Perkins, D., Schoenwaelder, J., Case,
                 J., Rose, M., and S. Waldbusser, "Textual Conventions
                 for SMIv2", STD 58, RFC 2579, April 1999.

   [RFC2580]     McCloghrie, K., Perkins, D., Schoenwaelder, J., Case,
                 J., Rose, M., and S. Waldbusser, "Conformance
                 Statements for SMIv2", STD 58, RFC 2580, April 1999.

   [RFC1157]     Case, J., Fedor, M., Schoffstall, M., and J. Davin,
                 "Simple Network Management Protocol", STD 15, RFC 1157,



Dubuc et al.             Expires November 2002                 [Page 80]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


                 May 1990.

   [RFC1901]     Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
                 "Introduction to Community-based SNMPv2", RFC 1901,
                 January 1996.

   [RFC1906]     Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
                 "Transport Mappings for Version 2 of the Simple Network
                 Management Protocol (SNMPv2)", RFC 1906, January 1996.

   [RFC2572]     Case, J., Harrington D., Presuhn R., and B. Wijnen,
                 "Message Processing and Dispatching for the Simple
                 Network Management Protocol (SNMP)", RFC 2572, April
                 1999.

   [RFC2574]     Blumenthal, U., and B. Wijnen, "User-based Security
                 Model (USM) for version 3 of the Simple Network
                 Management Protocol (SNMPv3)", RFC 2574, April 1999.

   [RFC1905]     Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
                 "Protocol Operations for Version 2 of the Simple
                 Network Management Protocol (SNMPv2)", RFC 1905,
                 January 1996.

   [RFC2573]     Levi, D., Meyer, P., and B. Stewart, "SNMPv3
                 Applications", RFC 2573, April 1999.

   [RFC2575]     Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based
                 Access Control Model (VACM) for the Simple Network
                 Management Protocol (SNMP)", RFC 2575, April 1999.

   [RFC2570]     Case, J., Mundy, R., Partain, D., and B. Stewart,
                 "Introduction to Version 3 of the Internet-standard
                 Network Management Framework", RFC 2570, April 1999.

   [IPSEC]       Kent, S., and Atkinson, R., "Security Architecture
                 for the Internet Protocol", RFC 2401, November
                 1998.

   [IFMIB]       McCloghrie, K., and Kastenholtz, F., "The Interfaces
                 Group MIB", RFC 2863, June 2000.

   [BCP14]       Bradner, S., "Key words for use in RFCs to Indicate
                 Requirement Levels", BCP 14, RFC 2119, March 1997.







Dubuc et al.             Expires November 2002                 [Page 81]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


14.  Authors' Addresses

Martin Dubuc                         Jonathan P. Lang
Meriton Networks                     Calient Networks, Inc.
3026 Solandt Road                    25 Castilian Drive
Kanata, ON, CANADA K2K 2A5           Goleta, CA 93117
Phone: +1-613-270-9279 x253          Email: jplang@calient.net
Email: martin.dubuc@meriton.com

Sudheer Dharanikota                  Evan McGinnis
Nayna Networks, Inc.                 Calient Networks, Inc.
157 Topaz Street                     5853 Rue Ferrari
Milipitas, CA 95035                  San Jose, CA 95138
Phone: +1-408-956-8000 x357          Email: evan@calient.net
Email: sudheer@nayna.com

Thomas D. Nadeau
Cisco Systems, Inc.
300 Apollo Drive
Chelmsford, MA 01824
Phone: +1-978-244-3051
Email: tnadeau@cisco.com


15.  Full Copyright Statement


   Copyright (C) The Internet Society (2001). All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works. However, this docu-
   ment itself may not be modified in any way, such as by removing the
   copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of develop-
   ing Internet standards in which case the procedures for copyrights
   defined in the Internet Standards process must be followed, or as
   required to translate it into languages other than English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.  This
   document and the information contained herein is provided on an "AS
   IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK
   FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
   LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL



Dubuc et al.             Expires November 2002                 [Page 82]

Internet Draft               CCAMP LMP MIB                  May 29, 2002


   NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY
   OR FITNESS FOR A PARTICULAR PURPOSE.

















































Dubuc et al.             Expires November 2002                 [Page 83]


Html markup produced by rfcmarkup 1.109, available from https://tools.ietf.org/tools/rfcmarkup/