[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 04 05 06 RFC 4137

EAP Working Group                                          J. Vollbrecht
Internet-Draft                                 Vollbrecht Consulting LLC
Expires: March 25, 2005                                        P. Eronen
draft-ietf-eap-statemachine-05                                     Nokia
                                                              N. Petroni
                                                  University of Maryland
                                                                 Y. Ohba
                                                                    TARI
                                                      September 24, 2004

      State Machines for Extensible Authentication Protocol (EAP)
                         Peer and Authenticator

Status of this Memo

   By submitting this Internet-Draft, I certify that any applicable
   patent or other IPR claims of which I am aware have been disclosed,
   or will be disclosed, and any of which I become aware will be
   disclosed, in accordance with RFC 3668.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than a "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/1id-abstracts.html

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html

Copyright Notice

   Copyright (C) The Internet Society (2004).  All Rights Reserved.

Abstract

   This document describes a set of state machines for Extensible
   Authentication Protocol (EAP) peer, EAP standalone authenticator
   (non-pass-through), EAP backend authenticator (for use on
   Authentication, Authorization and Accounting (AAA) servers), and EAP
   full authenticator (for both local and pass-through).  This set of
   state machines shows how EAP can be implemented to support deployment
   in either a peer/authenticator or peer/authenticator/AAA Server
   environment.  The peer and standalone authenticator machines are
   illustrative of how the EAP protocol defined in RFC 3748 may be
   implemented.  The backend and full/pass-through authenticators



Vollbrecht, et al.            Informational                     [Page 1]

Internet-Draft             EAP State Machines             September 2004


   illustrate how EAP/AAA protocol support defined in RFC 3579 may be
   implemented.  Where there are differences RFC 3748/RFC 3579 are
   authoritative.

   The state machines are based on the EAP "Switch" model.  This model
   includes events and actions for the interaction between the EAP
   Switch and EAP methods.  A brief description of the EAP "Switch"
   model is given in the Introduction section.

   The state machine and associated model are informative only.
   Implementations may achieve the same results using different methods.








































Vollbrecht, et al.            Informational                     [Page 2]

Internet-Draft             EAP State Machines             September 2004


Table of Contents

   1.  Specification of Requirements  . . . . . . . . . . . . . . . .  4
   2.  The EAP Switch Model . . . . . . . . . . . . . . . . . . . . .  4
   3.  Notational conventions used in state diagrams  . . . . . . . .  5
       3.1.  Notational specifics . . . . . . . . . . . . . . . . . .  5
       3.2.  State Machine Symbols. . . . . . . . . . . . . . . . . .  8
       3.3.  Document authority . . . . . . . . . . . . . . . . . . .  9
   4.  Peer State Machine . . . . . . . . . . . . . . . . . . . . . . 10
       4.1.  Interface between peer state machine and lower layer . . 10
       4.2.  Interface between peer state machine and methods . . . . 12
       4.3.  Peer state machine local variables . . . . . . . . . . . 14
       4.4.  Peer state machine procedures. . . . . . . . . . . . . . 15
       4.5.  Peer state machine states. . . . . . . . . . . . . . . . 16
   5.  Standalone Authenticator State Machine . . . . . . . . . . . . 18
       5.1.  Interface between standalone authenticator state machine
             and lower layer. . . . . . . . . . . . . . . . . . . . . 18
       5.2.  Interface between standalone authenticator state machine
             and methods. . . . . . . . . . . . . . . . . . . . . . . 20
       5.3.  Standalone authenticator state machine local variables . 22
       5.4.  EAP standalone authenticator procedures. . . . . . . . . 23
       5.5.  EAP standalone authenticator states. . . . . . . . . . . 25
   6.  EAP Backend Authenticator  . . . . . . . . . . . . . . . . . . 27
       6.1.  Interface between backend authenticator state machine
             and lower layer. . . . . . . . . . . . . . . . . . . . . 27
       6.2.  Interface between backend authenticator state machine
             and methods. . . . . . . . . . . . . . . . . . . . . . . 29
       6.3.  Backend authenticator state machine local variables. . . 29
       6.4.  EAP backend authenticator procedures . . . . . . . . . . 29
       6.5.  EAP backend authenticator states . . . . . . . . . . . . 30
   7.  EAP Full Authenticator . . . . . . . . . . . . . . . . . . . . 31
       7.1.  Interface between full authenticator state machine and
             lower layers . . . . . . . . . . . . . . . . . . . . . . 31
       7.2.  Interface between full authenticator state machine and
             methods  . . . . . . . . . . . . . . . . . . . . . . . . 33
       7.3.  Full authenticator state machine local variables . . . . 33
       7.4.  EAP full authenticator procedures. . . . . . . . . . . . 34
       7.5.  EAP full authenticator states. . . . . . . . . . . . . . 34
   8.  Implementation Considerations. . . . . . . . . . . . . . . . . 36
       8.1 Robustness . . . . . . . . . . . . . . . . . . . . . . . . 36
       8.2 Method/Method and Method/Lower-Layer Interfaces. . . . . . 36
   9.  Security Considerations  . . . . . . . . . . . . . . . . . . . 37
   10. Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . . 38
   11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 38
       11.1. Normative References . . . . . . . . . . . . . . . . . . 38
       11.2. Informative References . . . . . . . . . . . . . . . . . 38





Vollbrecht, et al.            Informational                     [Page 3]

Internet-Draft             EAP State Machines             September 2004


   Appendix. ASCII versions of state diagrams . . . . . . . . . . . . 40
       A.1.  EAP Peer State Machine (Figure 3)  . . . . . . . . . . . 40
       A.2.  EAP Standalone Authenticator State Machine (Figure 4)  . 43
       A.3.  EAP Backend Authenticator State Machine (Figure 5) . . . 46
       A.4.  EAP Full Authenticator State Machine (Figures 6 and 7) . 49
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 52
   Full Copyright Statement . . . . . . . . . . . . . . . . . . . . . 53

1.  Specification of Requirements

   In this document, several words are used to signify the requirements
   of the specification.  These words are often capitalized.  The key
   words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD",
   "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document
   are to be interpreted as described in [RFC2119].

2.  The EAP Switch Model

   This document offers a proposed state machine for RFCs [RFC3748] and
   [RFC3579].  There are state machines for the peer, the standalone
   authenticator, a backend authenticator and a full/pass-through
   authenticator.  Accompanying each state machine diagram is a
   description of the variables, the functions and the states in the
   diagram.  Whenever possible, the same notation has been used in each
   of the state machines.

   An EAP authentication consists of one or more EAP methods in sequence
   followed by an EAP Success or EAP Failure sent from the authenticator
   to the peer.  The EAP Switches control negotiation of EAP methods and
   sequences of methods.

      Peer             Peer  |  Authenticator       Auth
      Method                 |                      Method
              \              |                    /
               \             |                   /
                Peer         |             Auth
                EAP    <-----|---------->  EAP
                Switch       |             Switch

                    Figure 1: EAP Switch Model

   At both the peer and authenticator one or more EAP methods exist.
   The EAP switches select which methods each is willing to use, and
   negotiate between themselves to pick a method or sequence of methods.

   Note that the methods may also have state machines.  The details of
   these are outside the scope of this paper.




Vollbrecht, et al.            Informational                     [Page 4]

Internet-Draft             EAP State Machines             September 2004


       Peer  |  Authenticator              | Backend
             |              /   Local      |
             |             /    Method     |
       Peer  |        Auth                 |       Backend
       EAP --|----->  EAP                  |     -> EAP
      Switch |       Switch                |   /    Server
             |             \               |  /
             |              \ pass-through |
             |                             |

          Figure 2: EAP Pass-Through Model

   The Full/Pass-Through state machine allows a NAS or Edge Device to
   pass EAP Response messages to a Backend Server where the
   Authentication Method resides.  This paper includes a state machine
   for the EAP authenticator that supports both local and pass-through
   methods as well as a state machine for the backend authenticator
   existing at the AAA server.  A simple "Standalone" authenticator is
   also provided to show a basic, non-pass-through authenticator's
   behavior.

   This document describes a set of State Machines that can manage EAP
   authentication from the peer to an EAP method on the authenticator or
   from the peer through the authenticator pass-through method to the
   EAP method on the Backend EAP server.

   Some environments where EAP is used, such as PPP, may support peer-
   to-peer operation.  That is, both parties act as peers and
   authenticators at the same time, in two simultaneous and independent
   EAP conversations.  In this case, the implementation at each node has
   to perform demultiplexing of incoming EAP packets.  EAP packets with
   Code set to Response are delivered to the authenticator state machine
   and EAP packets with Code set to Request, Success or Failure are
   delivered to the peer state machine.

   The state diagrams presented in this document have been coordinated
   with the diagrams in [1X-REV].  The format of the diagrams is adapted
   from the format therein.  The interface between the state machines
   defined here and the IEEE-802-1X-REV state machines is also explained
   in Appendix F of [1X-REV].

3.  Notational conventions used in state diagrams

3.1.  Notational specifics

   The following state diagrams have been completed based on the
   conventions specified in [1X-REV], section 8.2.1.  The complete text
   is reproduced here:



Vollbrecht, et al.            Informational                     [Page 5]

Internet-Draft             EAP State Machines             September 2004


      State diagrams are used to represent the operation of the protocol
      by a number of cooperating state machines each comprising a group
      of connected, mutually exclusive states.  Only one state of each
      machine can be active at any given time.

      Each state is represented in the state diagram as a rectangular
      box, divided into two parts by a horizontal line.  The upper part
      contains the state identifier, written in upper case letters.  The
      lower part contains any procedures that are executed on entry to
      the state.

      All permissible transitions between states are represented by
      arrows, the arrowhead denoting the direction of the possible
      transition.  Labels attached to arrows denote the condition(s)
      that must be met in order for the transition to take place.  All
      conditions are expressions that evaluate to TRUE or FALSE; if a
      condition evaluates to TRUE, then the condition is met.  The label
      UCT denotes an unconditional transition (i.e., UCT always
      evaluates to TRUE).  A transition that is global in nature (i.e.,
      a transition that occurs from any of the possible states if the
      condition attached to the arrow is met) is denoted by an open
      arrow; i.e., no specific state is identified as the origin of the
      transition.  When the condition associated with a global
      transition is met, it supersedes all other exit conditions
      including UCT.  The special global condition BEGIN supersedes all
      other global conditions, and once asserted remains asserted until
      all state blocks have executed to the point that variable
      assignments and other consequences of their execution remain
      unchanged.

      On entry to a state, the procedures defined for the state (if any)
      are executed exactly once, in the order that they appear on the
      page.  Each action is deemed to be atomic; i.e., execution of a
      procedure completes before the next sequential procedure starts to
      execute.  No procedures execute outside of a state block.  The
      procedures in only one state block execute at a time, even if the
      conditions for execution of state blocks in different state
      machines are satisfied, and all procedures in an executing state
      block complete execution before the transition to and execution of
      any other state block occurs, i.e., the execution of any state
      block appears to be atomic with respect to the execution of any
      other state block and the transition condition to that state from
      the previous state is TRUE when execution commences.  The order of
      execution of state blocks in different state machines is undefined
      except as constrained by their transition conditions.  A variable
      that is set to a particular value in a state block retains this
      value until a subsequent state block executes a procedure that
      modifies the value.



Vollbrecht, et al.            Informational                     [Page 6]

Internet-Draft             EAP State Machines             September 2004


      On completion of all of the procedures within a state, all exit
      conditions for the state (including all conditions associated with
      global transitions) are evaluated continuously until one of the
      conditions is met.  The label ELSE denotes a transition that
      occurs if none of the other conditions for transitions from the
      state are met (i.e., ELSE evaluates to TRUE if all other possible
      exit conditions from the state evaluate to FALSE).  Where two or
      more exit conditions with the same level of precedence become TRUE
      simultaneously, the choice as to which exit condition causes the
      state transition to take place is arbitrary.

      Where it is necessary to split a state machine description across
      more than one diagram, a transition between two states that appear
      on different diagrams is represented by an exit arrow drawn with
      dashed lines, plus a reference to the diagram that contains the
      destination state.  Similarly, dashed arrows and a dashed state
      box are used on the destination diagram to show the transition to
      the destination state.  In a state machine that has been split in
      this way, any global transitions that can cause entry to states
      defined in one of the diagrams are deemed to be potential exit
      conditions for all of the states of the state machine, regardless
      of which diagram the state boxes appear in.

      Should a conflict exist between the interpretation of a state
      diagram and either the corresponding global transition tables or
      the textual description associated with the state machine, the
      state diagram takes precedence.  The interpretation of the special
      symbols and operators used in the state diagrams is as defined in
      Section 3.2; these symbols and operators are derived from the
      notation of the  C++  programming language, ISO/IEC 14882.  If a
      boolean variable is described in this clause as being set it has
      or is assigned the value TRUE, if reset or clear the value FALSE.

   In addition to the above notation, there are a couple of
   clarifications specific to this document.  First, all boolean
   variables are initialized to FALSE before the state machine execution
   begins.  Second, the following notational shorthand is specific to
   this document:

   <variable> = <expression1> | <expression2> | ...

      Execution of a statement of this form will result in <variable>
      having a value of exactly one of the expressions.  The logic for
      which of those expressions gets executed is outside of the state
      machine and could be environmental, configurable, or based on
      another state machine such as that of the method.





Vollbrecht, et al.            Informational                     [Page 7]

Internet-Draft             EAP State Machines             September 2004


3.2.  State Machine Symbols

   ( )

      Used to force the precedence of operators in Boolean expressions
      and to delimit the argument(s) of actions within state boxes.

   ;

      Used as a terminating delimiter for actions within state boxes.
      Where a state box contains multiple actions, the order of
      execution follows the normal English language conventions for
      reading text.

   =

      Assignment action.  The value of the expression to the right of
      the operator is assigned to the variable to the left of the
      operator.  Where this operator is used to define multiple
      assignments, e.g., a = b = X the action causes the value of the
      expression following the right-most assignment operator to be
      assigned to all of the variables that appear to the left of the
      right-most assignment operator.

   !

      Logical NOT operator.

   &&

      Logical AND operator.

   ||

      Logical OR operator.

   if...then...

      Conditional action.  If the Boolean expression following the if
      evaluates to TRUE, then the action following the then is executed.

   { statement 1, ... statement N }

      Compound statement.  Braces are used to group statements that are
      executed together as if they were a single statement.






Vollbrecht, et al.            Informational                     [Page 8]

Internet-Draft             EAP State Machines             September 2004


   !=

      Inequality.  Evaluates to TRUE if the expression to the left of
      the operator is not equal in value to the expression to the right.

   ==

      Equality.  Evaluates to TRUE if the expression to the left of the
      operator is equal in value to the expression to the right.

   >

      Greater than.  Evaluates to TRUE if the value of the expression to
      the left of the operator is greater than the value of the
      expression to the right.

   <=

      Less than or equal to.  Evaluates to TRUE if the value of the
      expression to the left of the operator is either less than or
      equal to the value of the expression to the right.

   ++

      Increment the preceding integer operator by 1.

3.3.  Document authority

   Should a conflict exist between the interpretation of a state diagram
   and either the corresponding global transition tables or the  textual
   description associated with the state machine, the state  diagram
   takes precedence.  When a discrepancy occurs between any part of this
   document (text or diagram) and any of the related documents
   ([RFC3748], [RFC3579], etc.) the latter (the other document) is
   considered authoritative and takes precedence.
















Vollbrecht, et al.            Informational                     [Page 9]

Internet-Draft             EAP State Machines             September 2004


4.  Peer State Machine

   The following is a diagram of the EAP peer state machine.  Also
   included is an explanation of the primitives and procedures
   referenced in the diagram, as well as a clarification of notation.

               (see the .pdf version for missing diagram or
            refer to Appendix A.1 if reading the .txt version)

                     Figure 3: EAP Peer State Machine

4.1.  Interface between peer state machine and lower layer

   The lower layer presents messages to the EAP peer state machine by
   storing the packet in eapReqData and setting the eapReq signal to
   TRUE.  Note that despite the name of the signal, the lower layer does
   not actually inspect the contents of the EAP packet (it could be a
   Success or Failure message instead of a Request).

   When the EAP peer state machine has finished processing the message
   it sets either eapResp or eapNoResp.  If it sets eapResp, the
   corresponding response packet is stored in eapRespData.  The lower
   layer is responsible for actually transmitting this message.  When
   the EAP peer state machine authentication is complete it will set
   eapSuccess or eapFailure to indicate to the lower layer that the
   authentication has succeeded or failed.

4.1.1.  Variables (lower layer to peer)

   eapReq (boolean)

      Set to TRUE in lower layer, FALSE in peer state machine.
      Indicates there is a request available in the lower layer.

   eapReqData (EAP packet)

      Set in lower layer when eapReq is set to TRUE.  The contents of
      the available request.

   portEnabled (boolean)

      Indicates that the EAP peer state machine should be ready for
      communication.  This is set to TRUE when the EAP conversation is
      started by the lower layer.  If at any point the communication
      port or session is not available, portEnabled is set to FALSE and
      the state machine transitions to DISABLED.  To avoid unnecessary
      resets, the lower layer may dampen link down indications when it
      believes that the link is only temporarily down and that it will



Vollbrecht, et al.            Informational                    [Page 10]

Internet-Draft             EAP State Machines             September 2004


      soon be back up (see [RFC3748], Section 7.12).  In this case,
      portEnabled may not always be equal to the the "link up" flag of
      the lower layer.

   idleWhile (integer)

      Outside timer used to indicate how long remains before the peer
      will timeout while waiting for a valid request.

   eapRestart (boolean)

      Indicates the lower layer would like to restart authentication

   altAccept (boolean)

      Alternate indication of success, as described in [RFC3748].

   altReject (boolean)

      Alternate indication of failure, as described in [RFC3748].

4.1.2.  Variables (peer to lower layer)

   eapResp (boolean)

      Set to TRUE in peer state machine, FALSE in lower layer.
      Indicates there is a response to be sent.

   eapNoResp (boolean)

      Set to TRUE in peer state machine, FALSE in lower layer.
      Indicates the request has been processed, but there is no response
      to send.

   eapSuccess (boolean)

      Set to TRUE in peer state machine, FALSE in lower layer.
      Indicates the Peer has reached the SUCCESS state.

   eapFail (boolean)

      Set to TRUE in peer state machine, FALSE in lower layer.
      Indicates the Peer has reached the FAILURE state.

   eapRespData (EAP packet)

      Set in peer state machine when eapResp is set to TRUE.  The EAP
      packet which is the response to send.



Vollbrecht, et al.            Informational                    [Page 11]

Internet-Draft             EAP State Machines             September 2004


   eapKeyData (EAP key)

      Set in peer state machine when keying material becomes available.
      Set during the METHOD state.  Note that this document does not yet
      define the structure of the type "EAP key".  We expect it to be
      defined in [Keying].

   eapKeyAvailable (boolean)

      Set to TRUE in the SUCCESS state if keying material is available.
      The actual key is stored in eapKeyData.

4.1.3.  Constants

   ClientTimeout (integer)

      Configurable amount of time to wait for a valid request before
      aborting, initialized by implementation-specific means (e.g., a
      configuration setting).

4.2.  Interface between peer state machine and methods

   IN: eapReqData (includes reqId)

   OUT: ignore, eapRespData, allowNotifications, decision

   IN/OUT: methodState, (method-specific state)

   The following describes the interaction between the state machine and
   EAP methods.

   If methodState==INIT, the method starts by initializing its own
   method-specific state.

   Next, the method must decide whether to process the packet or
   silently discard it.  If the packet appears to have been sent by
   someone other than the legitimate authenticator (for instance,
   message integrity check fails) and the method is capable of treating
   such situations as non-fatal, the method can set ignore=TRUE.  In
   this case, the method should not modify any other variables.

   If the method decides to process the packet, it behaves as follows.

   o  Updates its own method-specific state.

   o  If the method has derived keying material it wants to export,
      stores the keying material to eapKeyData.




Vollbrecht, et al.            Informational                    [Page 12]

Internet-Draft             EAP State Machines             September 2004


   o  Creates a response packet (with the same identifier as the
      request), and stores it to eapRespData.

   o  Sets ignore=FALSE.

   Next, the method must update methodState and decision according to
   the following rules.

   methodState=CONT: The method always continues at this point (and the
      peer wants to continue it).  The decision variable is always set
      to FAIL.

   methodState=MAY_CONT: At this point, the authenticator can decide
      either to continue the method or end the conversation.  The
      decision variable tells us what to do in the case the conversation
      ends.  If the current situation does not satisfy the peer's
      security policy (that is, if the authenticator now decides to
      allow access, the peer will not use it), set decision=FAIL.
      Otherwise, set decision=COND_SUCC.

   methodState=DONE: The method never continues at this point, (or the
      peer sees no point in continuing it).

      If either (a) the authenticator has informed us that it will not
      allow access, or (b) we're not willing to talk to this
      authenticator (e.g., our security policy is not satisfied), set
      decision=FAIL.  (Note that this state can occur even if the method
      still has additional messages left, if continuing it can not
      change the peer's decision to success).

      If both (a) the server has informed us that it will allow access
      and the next packet will be EAP Success, and (b) we're willing to
      use this access, set decision=UNCOND_SUCC.

      Otherwise, we do not know what the server's decision is, but are
      willing to use the access if the server allows.  In this case, set
      decision=COND_SUCC.

   Finally, the method must set the allowNotifications variable.  If the
   new methodState is either CONT or MAY_CONT, and the method
   specification does not forbid the use of Notification messages, set
   allowNotifications=TRUE.  Otherwise, set allowNotifications=FALSE.









Vollbrecht, et al.            Informational                    [Page 13]

Internet-Draft             EAP State Machines             September 2004


4.3.  Peer state machine local variables

4.3.1.  Long-term (maintained between packets)

   selectMethod (EAP type)

      Set in GET_METHOD state.  The method the peer believes to be
      currently "in progress"

   methodState (enumeration)

      As described above.

   lastId (integer)

      0-255 or NONE.  Set in SEND_RESPONSE state.  The EAP identifier
      value of the last request.

   lastRespData (EAP packet)

      Set in SEND_RESPONSE state.  The EAP packet last sent from the
      peer.

   decision (enumeration)

      As described above

   NOTE: EAP type can be normal type (0..253,255), or an extended type
   consisting of type 254, Vendor-Id, and Vendor-Type.

4.3.2.  Short-term (not maintained between packets)

   rxReq (boolean)

      Set in RECEIVED state.  Indicates the current received packet is
      an EAP request.

   rxSuccess (boolean)

      Set in RECEIVED state.  Indicates the current received packet is
      an EAP Success.

   rxFailure (boolean)

      Set in RECEIVED state.  Indicates the current received packet is
      an EAP Failure.





Vollbrecht, et al.            Informational                    [Page 14]

Internet-Draft             EAP State Machines             September 2004


   reqId (integer)

      Set in RECEIVED state.  The identifier value associated with the
      current EAP request.

   reqMethod (EAP type)

      Set in RECEIVED state.  The method type of the current EAP request

   ignore (boolean)

      Set in METHOD state.  Indicates whether the method has decided to
      drop the current packet.

4.4.  Peer state machine procedures

   NOTE: For method procedures, the method uses its internal state in
   addition to the information provided by the EAP layer.  The only
   arguments that are explicitly shown as inputs to the procedures are
   those provided to the method by EAP.  Those inputs provided by the
   method's internal state remain implicit.

   parseEapReq()

      Determine the code, identifier value, and type of the current
      request.  In case of a parsing error (e.g., the length field is
      longer than the received packet), rxReq, rxSuccess, and rxFailure
      will all be set to FALSE.  The values of reqId and reqMethod may
      be undefined as a result.  Returns three booleans, one integer,
      and one EAP type.

   processNotify()

      Process the contents of Notification Request (for instance,
      display it to the user or log it).  Return value is undefined.

   buildNotify()

      Create the appropriate notification response.  Returns an EAP
      packet.











Vollbrecht, et al.            Informational                    [Page 15]

Internet-Draft             EAP State Machines             September 2004


   processIdentity()

      Process the contents of Identity Request.  Return value is
      undefined.

   buildIdentity()

      Create the appropriate identity response.  Returns an EAP packet.

   m.check()

      Method-specific procedure to test for the validity of a message.
      Returns a boolean.

   m.process()

      Method procedure to parse and process a request for that method.
      Returns a methodState enumeration, a decision enumeration, and a
      boolean.

   m.buildResp()

      Method procedure to create a response message.  Returns an EAP
      packet.

   m.getKey()

      Method procedure to obtain key material for use by EAP or lower
      layers.  Returns an EAP key.

4.5.  Peer state machine states

   DISABLED

      This state is reached anytime service from the lower layer is
      interrupted or unavailable.  Immediate transition to INITIALIZE
      occurs when the port becomes enabled.

   INITIALIZE

      Initializes variables when the state machine is activated.

   IDLE

      The state machine spends most of its time here, waiting for
      something to happen.





Vollbrecht, et al.            Informational                    [Page 16]

Internet-Draft             EAP State Machines             September 2004


   RECEIVED

      This state is entered when an EAP packet is received: the packet
      header is parsed here.

   GET_METHOD

      This state is entered when a request for a new type comes in:
      either the correct method is started, or a Nak response is built.

   METHOD

      The method processing happens here: the request from the
      authenticator is processed, and an appropriate response packet is
      built.

   SEND_RESPONSE

      This state signals the lower layer that a response packet is ready
      to be sent.

   DISCARD

      This state signals the lower layer that the request was discarded,
      and no response packet will be sent at this time.

   IDENTITY:

      Handles requests for Identity method, and builds a response.

   NOTIFICATION

      Handles requests for Notification method, and builds a response.

   RETRANSMIT

      Retransmits the previous response packet.

   SUCCESS

      A final state indicating success.

   FAILURE

      A final state indicating failure.






Vollbrecht, et al.            Informational                    [Page 17]

Internet-Draft             EAP State Machines             September 2004


5.  Standalone Authenticator State Machine

   The following is a diagram of the "Standalone" EAP authenticator
   state machine.  This diagram should be used for those interested in a
   self-contained, or non-pass-through, authenticator.  Included is an
   explanation of the primitives and procedures referenced in the
   diagram, as well as a clarification of notation.

               (see the .pdf version for missing diagram or
            refer to Appendix A.2 if reading the .txt version)

           Figure 4: EAP Standalone Authenticator State Machine

5.1.  Interface between standalone authenticator state machine and lower
   layer

   The lower layer presents messages to the EAP authenticator state
   machine by storing the packet in eapRespData and setting the eapResp
   signal to TRUE.

   When the EAP authenticator state machine has finished processing the
   message, it sets one of the signals eapReq, eapNoReq, eapSuccess, and
   eapFail.  If it sets eapReq, eapSuccess, or eapFail, the
   corresponding request (or success/failure) packet is stored in
   eapReqData.  The lower layer is responsible for actually transmitting
   this message.

5.1.1.  Variables (lower layer to standalone authenticator)

   eapResp (boolean)

      Set to TRUE in lower layer, FALSE in authenticator state machine.
      Indicates an EAP response is available for processing.

   eapRespData (EAP packet)

      Set in lower layer when eapResp is set to TRUE.  The EAP packet to
      be processed.

   portEnabled (boolean)

      Indicates that the EAP authenticator state machine should be ready
      for communication.  This is set to TRUE when the EAP conversation
      is started by the lower layer.  If at any point the communication
      port or session is not available, portEnabled is set to FALSE and
      the state machine transitions to DISABLED.  To avoid unnecessary
      resets, the lower layer may dampen link down indications when it
      believes that the link is only temporarily down and that it will



Vollbrecht, et al.            Informational                    [Page 18]

Internet-Draft             EAP State Machines             September 2004


      soon be back up (see [RFC3748], Section 7.12).  In this case,
      portEnabled may not always be equal to the the "link up" flag of
      the lower layer.

   retransWhile (integer)

      Outside timer used to indicate how long the authenticator has
      waited for a new (valid) response.

   eapRestart (boolean)

      Indicates the lower layer would like to restart authentication

   eapSRTT (integer)

      Smoothed round-trip time.  (see [RFC3748], Section 4.3)

   eapRTTVAR (integer)

      Round-trip time variation.  (see [RFC3748], Section 4.3)

5.1.2.  Variables (standalone authenticator to lower layer)

   eapReq (boolean)

      Set to TRUE in authenticator state machine, FALSE in lower layer.
      Indicates a new EAP request is ready to be sent.

   eapNoReq (boolean)

      Set to TRUE in authenticator state machine, FALSE in lower layer.
      Indicates the most recent response has been processed, but there
      is no new request to send.

   eapSuccess (boolean)

      Set to TRUE in authenticator state machine, FALSE in lower layer.
      Indicates the state machine has reached the SUCCESS state.

   eapFail (boolean)

      Set to TRUE in authenticator state machine, FALSE in lower layer.
      Indicates the state machine has reached the FAILURE state.








Vollbrecht, et al.            Informational                    [Page 19]

Internet-Draft             EAP State Machines             September 2004


   eapTimeout (boolean)

      Set to TRUE in the TIMEOUT_FAILURE state if the authenticator has
      reached its maximum number of retransmissions without receiving a
      response.


   eapReqData (EAP packet)

      Set in authenticator state machine when eapReq, eapSuccess, or
      eapFail is set to TRUE.  The actual EAP request to be sent (or
      success/failure).

   eapKeyData (EAP key)

      Set in authenticator state machine when keying material becomes
      available.  Set during the METHOD state.  Note that this document
      does not yet define the structure of the type "EAP key".  We
      expect it to be defined in [Keying].

   eapKeyAvailable (boolean)

      Set to TRUE in the SUCCESS state if keying material is available.
      The actual key is stored in eapKeyData.

5.1.3.  Constants

   MaxRetrans (integer)

      Configurable maximum for how many retransmissions should be
      attempted before aborting.

5.2.  Interface between standalone authenticator state machine and
   methods

   IN: eapRespData, methodState

   OUT: ignore, eapReqData

   IN/OUT: currentId, (method-specific state), (policy)

   The following describes the interaction between the state machine and
   EAP methods.

   m.init (in: -, out: -)

   When the method is first started, it must initialize its own method-
   specific state, possibly using some information from Policy (e.g.,



Vollbrecht, et al.            Informational                    [Page 20]

Internet-Draft             EAP State Machines             September 2004


   identity).

   m.buildReq (in: integer, out: EAP packet)

   Next, the method creates a new EAP Request packet, with the given
   identifier value, and updates its method-specific state accordingly.

   m.getTimeout (in: -, out: integer or NONE)

   The method can also provide a hint for retransmission timeout with
   m.getTimeout.

   m.check (in: EAP packet, out: boolean)

   When a new EAP Response is received, the method must first decide
   whether to process the packet or silently discard it.  If the packet
   looks like it was not sent by the legitimate peer (e.g., it has
   invalid MIC, and this case should never occur), the method can
   indicate this by returning FALSE.  In this case, the method should
   not modify its own method-specific state.

   m.process (in: EAP packet, out: -)

   m.isDone (in: -, out: boolean)

   m.getKey (in: -, out: EAP key or NONE)

   Next, the method processes the EAP Response and updates its own
   method-specific state.  Now the options are to continue the
   conversation (send another request) or end this method.

   If the method wants to end the conversation, it

   o  Tells Policy about the outcome of the method, and possibly other
      information.

   o  If the method has derived keying material it wants to export,
      returns it from m.getKey().

   o  Indicates that the method wants to end by returning TRUE from
      m.isDone().

   Otherwise, the method continues by sending another request, as
   described earlier.







Vollbrecht, et al.            Informational                    [Page 21]

Internet-Draft             EAP State Machines             September 2004


5.3.  Standalone authenticator state machine local variables

5.3.1.  Long-term (maintained between packets)

   currentMethod (EAP type)

      EAP type, IDENTITY, or NOTIFICATION.

   currentId (integer)

      0-255 or NONE.  Usually updated in PROPOSE_METHOD state.
      Indicates the identifier value of the currently outstanding EAP
      request.

   methodState (enumeration)

      As described above.

   retransCount (integer)

      Reset in SEND_REQUEST state and updated in RETRANSMIT state.
      Current number of retransmissions.

   lastReqData (EAP packet)

      Set in SEND_REQUEST state.  EAP packet containing the last sent
      request.

   methodTimeout (integer)

      Method-provided hint for suitable retransmission timeout, or NONE.

5.3.2.  Short-term (not maintained between packets)

   rxResp (boolean)

      Set in RECEIVED state.  Indicates the current received packet is
      an EAP response.

   respId (integer)

      Set in RECEIVED state.  The identifier from the current EAP
      response.

   respMethod (EAP type)

      Set in RECEIVED state.  The method type of the current EAP
      response.



Vollbrecht, et al.            Informational                    [Page 22]

Internet-Draft             EAP State Machines             September 2004


   ignore (boolean)

      Set in METHOD state.  Indicates whether the method has decided to
      drop the current packet.

   decision (enumeration)

      Set in SELECT_ACTION state.  Temporarily store the policy decision
      to succeed, fail, or continue.

5.4.  EAP standalone authenticator procedures

   NOTE: For method procedures, the method uses its internal state in
   addition to the information provided by the EAP layer.  The only
   arguments that are explicitly shown as inputs to the procedures are
   those provided to the method by EAP.  Those inputs provided by the
   method's internal state remain implicit.

   calculateTimeout()

      Calculates the retransmission timeout, taking into account the
      retransmission count, round-trip time measurements, and method-
      specific timeout hint (see [RFC3748], Section 4.3).  Returns an
      integer.

   parseEapResp()

      Determine the code, identifier value, and type of the current
      response.  In case of a parsing error (e.g., the length field is
      longer than the received packet), rxResp will be set to FALSE.
      The values of respId and respMethod may be undefined as a result.
      Returns a boolean, an integer, and an EAP type.

   buildSuccess()

      Create an EAP Success Packet.  Returns an EAP packet.

   buildFailure()

      Create an EAP Failure Packet.  Returns an EAP packet.

   nextId()

      Determine the next identifier value to use, based on the previous
      one.  Returns an integer.






Vollbrecht, et al.            Informational                    [Page 23]

Internet-Draft             EAP State Machines             September 2004


   Policy.update()

      Update all variables related to internal policy state.  Return
      value is undefined.

   Policy.getNextMethod()

      Determine the method that should be used at this point in the
      conversation based on pre-defined policy.  Policy.getNextMethod()
      MUST comply with [RFC3748] (Section 2.1), which forbids the use of
      sequences of authentication methods within an EAP conversation.
      Hence, if an authentication method has already been executed
      within an EAP dialog, Policy.getNextMethod() MUST NOT propose
      another authentication method within the same EAP dialog.  Returns
      an EAP type.

   Policy.getDecision()

      Determine if the policy will allow SUCCESS, FAIL, or is yet to
      determine (CONTINUE).  Returns a decision enumeration.

   m.check()

      Method-specific procedure to test for the validity of a message.
      Returns a boolean.

   m.process()

      Method procedure to parse and process a response for that method.
      Return value is undefined.

   m.init()

      Method procedure to initialize state just before use.  Return
      value is undefined.

   m.reset()

      Method procedure to indicate the method is ending in the middle or
      before completion.  Return value is undefined.

   m.isDone()

      Method procedure to check for method completion.  Returns a
      boolean.






Vollbrecht, et al.            Informational                    [Page 24]

Internet-Draft             EAP State Machines             September 2004


   m.getTimeout()

      Method procedure to determine an appropriate timeout hint for that
      method.  Returns an integer.

   m.getKey()

      Method procedure to obtain key material for use by EAP or lower
      layers.  Returns an EAP key.

   m.buildReq()

      Method procedure to produce the next request.  Returns an EAP
      packet.

5.5.  EAP standalone authenticator states

   DISABLED

      The authenticator is disabled until the port is enabled by the
      lower layer.

   INITIALIZE

      Initializes variables when the state machine is activated.

   IDLE

      The state machine spends most of its time here, waiting for
      something to happen.

   RECEIVED

      This state is entered when an EAP packet is received: the packet
      header is parsed here.

   INTEGRITY_CHECK

      A method state in which the integrity of the incoming packet from
      the peer is verified by the method.

   METHOD_RESPONSE

      A method state in which the incoming packet is processed.

   METHOD_REQUEST

      A method state in which a new request is formulated if necessary.



Vollbrecht, et al.            Informational                    [Page 25]

Internet-Draft             EAP State Machines             September 2004


   PROPOSE_METHOD

      A state in which the authenticator decides which method to try
      next in the authentication.

   SELECT_ACTION

      In between methods, the state machine re-evaluates whether or not
      its policy is satisfied and succeeds, fails, or remains undecided.

   SEND_REQUEST

      This state signals the lower layer that a request packet is ready
      to be sent.

   DISCARD

      This state signals the lower layer that the response was
      discarded, and no new request packet will be sent at this time.

   NAK

      This state processes Nak responses from the peer.

   RETRANSMIT

      Retransmits the previous request packet.

   SUCCESS

      A final state indicating success.

   FAILURE

      A final state indicating failure.

   TIMEOUT_FAILURE

      A final state indicating failure because no response has been
      received.  Because no response was received, no new message
      (including failure) should be sent to the peer.  Note that this is
      different from the FAILURE state, where a message indicating
      failure is sent to the peer.








Vollbrecht, et al.            Informational                    [Page 26]

Internet-Draft             EAP State Machines             September 2004


6.  EAP Backend Authenticator

   When operating in pass-through mode, there are conceptually two parts
   to the authenticator - the part that passes packets through and the
   backend that actually implements the EAP method.  The following
   diagram shows a state machine for the backend part of this model when
   using a AAA server.  Note that this diagram is identical to Figure 4
   except no retransmit is included in the IDLE state because with
   RADIUS retransmit is handled by the NAS, and  a PICK_UP_METHOD state
   and variable in INITIALIZE state are added to allow the Method to
   "pickup" a method started in a NAS.  Included is an explanation of
   the primitives and procedures referenced in the diagram, many of
   which are the same as above.  It should be noted that the "lower
   layer" in this case is some AAA protocol (e.g., RADIUS).

               (see the .pdf version for missing diagram or
            refer to Appendix A.3 if reading the .txt version)

             Figure 5: EAP Backend Authenticator State Machine

6.1.  Interface between backend authenticator state machine and lower
   layer

   The lower layer presents messages to the EAP backend authenticator
   state machine by storing the packet in aaaEapRespData and setting the
   aaaEapResp signal to TRUE.

   When the EAP backend authenticator state machine has finished
   processing the message, it sets one of the signals aaaEapReq,
   aaaEapNoReq, aaaSuccess, and aaaFail.  If it sets eapReq, eapSuccess,
   or eapFail, the corresponding request (or success/failure) packet is
   stored in aaaEapReqData.  The lower layer is responsible for actually
   transmitting this message.

6.1.1.  Variables (AAA interface to backend authenticator)

   aaaEapResp (boolean)

      Set to TRUE in lower layer, FALSE in authenticator state machine.
      Usually indicates that an EAP response, stored in aaaEapRespData,
      is available for processing by the AAA server.  If aaaEapRespData
      is set to NONE, indicates that the AAA server should send the
      initial EAP request.








Vollbrecht, et al.            Informational                    [Page 27]

Internet-Draft             EAP State Machines             September 2004


   aaaEapRespData (EAP packet)

      Set in lower layer when eapResp is set to TRUE.  The EAP packet to
      be processed or NONE.

   backendEnabled (boolean)

      Indicates that there is a valid link to use for the communication.
      If at any point the port is not available, backendEnabled is set
      to FALSE and the state machine transitions to DISABLED.

6.1.2.  Variables (backend authenticator to AAA interface)

   aaaEapReq (boolean)

      Set to TRUE in authenticator state machine, FALSE in lower layer.
      Indicates a new EAP request is ready to be sent.

   aaaEapNoReq (boolean)

      Set to TRUE in authenticator state machine, FALSE in lower layer.
      Indicates the most recent response has been processed, but there
      is no new request to send.

   aaaSuccess (boolean)

      Set to TRUE in authenticator state machine, FALSE in lower layer.
      Indicates the state machine has reached the SUCCESS state.

   aaaFail (boolean)

      Set to TRUE in authenticator state machine, FALSE in lower layer.
      Indicates the state machine has reached the FAILURE state.

   aaaEapReqData (EAP packet)

      Set in authenticator state machine when aaaEapReq, aaaSuccess, or
      aaaFail is set to TRUE.  The actual EAP request to be sent (or
      success/failure).

   aaaEapKeyData (EAP key)

      Set in authenticator state machine when keying material becomes
      available.  Set during the METHOD_RESPONSE state.  Note that this
      document does not yet define the structure of the type "EAP key".
      We expect it to be defined in [Keying].





Vollbrecht, et al.            Informational                    [Page 28]

Internet-Draft             EAP State Machines             September 2004


   aaaEapKeyAvailable (boolean)

      Set to TRUE in the SUCCESS state if keying material is available.
      The actual key is stored in aaaEapKeyData.

   aaaMethodTimeout (integer)

      Method-provided hint for suitable retransmission timeout, or NONE
      (note that this hint is for the EAP retransmissions done by the
      pass-through authenticator, not retransmissions of AAA packets).

6.2.  Interface between backend authenticator state machine and methods

   The backend method interface is almost the same as in standalone
   authenticator described in Section 5.2.  The only difference is that
   some methods on the backend may support "picking up" a conversation
   started by the pass-through.  That is, the EAP Request packet was
   sent by the pass-through, but the backend must process the
   corresponding EAP Response.  Usually only the Identity method
   supports this, but others are possible.

   When "picking up" a conversation, m.initPickUp() is called instead of
   m.init().  Next, m.process() must examine eapRespData and update its
   own method-specific state to match what it would have been if it had

   actually sent the corresponding request.  (Obviously, this only works
   for methods that can determine what the initial request contained;
   Identity and EAP-TLS are good examples.)

   After this, the processing continues as described in Section 5.2.

6.3.  Backend authenticator state machine local variables

   For definitions of the variables used in the Backend Authenticator,
   see Section 5.3.

6.4.  EAP backend authenticator procedures

   Most of the procedures of the backend authenticator have already been
   defined in Section 5.4.  This section contains definitions for those
   not existent in the standalone version, as well as those which are
   defined differently.

   NOTE: For method procedures, the method uses its internal state in
   addition to the information provided by the EAP layer.  The only
   arguments that are explicitly shown as inputs to the procedures are
   those provided to the method by EAP.  Those inputs provided by the
   method's internal state remain implicit.



Vollbrecht, et al.            Informational                    [Page 29]

Internet-Draft             EAP State Machines             September 2004


   Policy.doPickUp()

      Notify the policy that an already-chosen method is being picked up
      and will be completed.  Returns a boolean.

   m.initPickUp()

      Method procedure to initialize state when continuing from an
      already-started method.  Return value is undefined.

6.5.  EAP backend authenticator states

   Most of the states of the backend authenticator have already been
   defined in Section 5.5.  This section contains definitions for those
   not existent in the standalone version, as well as those which are
   defined differently.

   PICK_UP_METHOD

      Set an initial state for a method that is being continued and was
      started elsewhere.






























Vollbrecht, et al.            Informational                    [Page 30]

Internet-Draft             EAP State Machines             September 2004


7.  EAP Full Authenticator

   The following two diagrams show the state machine for a complete
   authenticator.  The first diagram is identical to the Standalone
   State Machine, shown in Figure 4, with the exception that the
   SELECT_ACTION state has an added transition to PASSTHROUGH.  The
   second diagram also keeps most of the logic except the four method
   states, and shows how the state machine works once it goes to Pass-
   Through Mode.

   The first diagram is largely a reproduction of that found above, with
   the added hooks for a transition to PASSTHROUGH mode.

               (see the .pdf version for missing diagram or
            refer to Appendix A.4 if reading the .txt version)

          Figure 6: EAP Full Authenticator State Machine (Part 1)

   The second diagram describes the functionality necessary for an
   authenticator operating in pass-through mode.  This section of the
   diagram is the counterpart of the backend diagram above.

               (see the .pdf version for missing diagram or
            refer to Appendix A.4 if reading the .txt version)

          Figure 7: EAP Full Authenticator State Machine (Part 2)

7.1.  Interface between full authenticator state machine and lower
   layers

   The full authenticator is unique in that it interfaces to multiple
   lower layers in order to support pass-through mode.  The interface to
   the primary EAP transport layer is the same as described in Section
   5.  The following describes the interface to the second lower layer,
   which represents an interface to AAA.  It should be noted that there
   is not necessarily a direct interaction between the EAP layer and the
   AAA layer, as in the case of [1X-REV].

7.1.1.  Variables (AAA interface to full authenticator)

   aaaEapReq (boolean)

      Set to TRUE in lower layer, FALSE in authenticator state machine.
      Indicates a new EAP request is available from the AAA server.







Vollbrecht, et al.            Informational                    [Page 31]

Internet-Draft             EAP State Machines             September 2004


   aaaEapNoReq (boolean)

      Set to TRUE in lower layer, FALSE in authenticator state machine.
      Indicates the most recent response has been processed, but there
      is no new request to send.

   aaaSuccess (boolean)

      Set to TRUE in lower layer.  Indicates the AAA backend
      authenticator has reached the SUCCESS state.

   aaaFail (boolean)

      Set to TRUE in lower layer.  Indicates the AAA backend
      authenticator has reached the FAILURE state.

   aaaEapReqData (EAP packet)

      Set in the lower layer when aaaEapReq, aaaSuccess, or aaaFail is
      set to TRUE.  The actual EAP request to be sent (or success/
      failure).

   aaaEapKeyData (EAP key)

      Set in lower layer when keying material becomes available from the
      AAA server.  Note that this document does not yet define the
      structure of the type "EAP key".  We expect it to be defined in
      [Keying].

   aaaEapKeyAvailable (boolean)

      Set to TRUE in the lower layer if keying material is available.
      The actual key is stored in aaaEapKeyData.

   aaaMethodTimeout (integer)

      Method-provided hint for suitable retransmission timeout, or NONE
      (note that this hint is for the EAP retransmissions done by the
      pass-through authenticator, not retransmissions of AAA packets).

7.1.2.  Variables (full authenticator to AAA interface)

   aaaEapResp (boolean)

      Set to TRUE in authenticator state machine, FALSE in the lower
      layer.  Indicates an EAP response is available for processing by
      the AAA server.




Vollbrecht, et al.            Informational                    [Page 32]

Internet-Draft             EAP State Machines             September 2004


   aaaEapRespData (EAP packet)

      Set in authenticator state machine when eapResp is set to TRUE.
      The EAP packet to be processed.

   aaaIdentity (EAP packet)

      Set in authenticator state machine when an IDENTITY response is
      received.  Makes that identity available to AAA lower layer.

   aaaTimeout (boolean)

      Set in AAA_IDLE if after a configurable amount of time there is no
      response from the AAA layer.  The AAA layer in the NAS is itself
      alive and OK, but for some reason it has not received a valid
      Access-Accept/Reject indication from the backend

7.1.3.  Constants

   Same as Section 5.

7.2.  Interface between full authenticator state machine and methods

   Same as standalone authenticator (Section 5.2)

7.3.  Full authenticator state machine local variables

   Many of the variables of the full authenticator have already been
   defined in Section 5.  This section contains definitions for those
   not existent in the standalone version, as well as those which are
   defined differently.

7.3.1.  Short-term (not maintained between packets)

   decision (enumeration)

      Set in SELECT_ACTION state.  Temporarily store the policy decision
      to succeed, fail, continue with a local method, or continue in
      pass-through mode.












Vollbrecht, et al.            Informational                    [Page 33]

Internet-Draft             EAP State Machines             September 2004


7.4.  EAP full authenticator procedures

   All of the procedures defined in Section 5 exist in the full version.
   In addition, the following procedures are defined.

   getId()

      Determine the identifier value chosen by the AAA server for the
      current EAP request.  Return value is an integer.

7.5.  EAP full authenticator states

   All of the states defined in Section 5 exist in the full version.  In
   addition, the following states are defined.

   INITIALIZE_PASSTHROUGH

      Initializes variables when the pass-through portion of the state
      machine is activated.

   IDLE2

      The state machine waits for a response from the primary lower
      layer, which transports EAP traffic from the peer.

   IDLE

      The state machine spends most of its time here, waiting for
      something to happen.

   RECEIVED2

      This state is entered when an EAP packet is received and the
      authenticator is in PASSTHROUGH mode: the packet header is parsed
      here.

   AAA_REQUEST

      The incoming EAP packet is parsed for sending to the AAA server.

   AAA_IDLE

      Idle state which tells the AAA layer it has a response and then
      waits for a new request, a no-request signal, or success/failure.







Vollbrecht, et al.            Informational                    [Page 34]

Internet-Draft             EAP State Machines             September 2004


   AAA_RESPONSE

      State in which the request from the AAA interface is processed
      into an EAP request.

   SEND_REQUEST2

      This state signals the lower layer that a request packet is ready
      to be sent.

   DISCARD2

      This state signals the lower layer that the response was
      discarded, and no new request packet will be sent at this time.

   RETRANSMIT2

      Retransmits the previous request packet.

   SUCCESS2

      A final state indicating success.

   FAILURE2

      A final state indicating failure.

   TIMEOUT_FAILURE2

      A final state indicating failure because no response has been
      received.  Because no response was received, no new message
      (including failure) should be sent to the peer.  Note that this is
      different from the FAILURE2 state, where a message indicating
      failure is sent to the peer.

















Vollbrecht, et al.            Informational                    [Page 35]

Internet-Draft             EAP State Machines             September 2004


8.  Implementation Considerations

8.1.  Robustness

   In order to deal with erroneous cases that are not directly related
   to the protocol behavior, implementations may need additional
   considerations to provide robustness against errors.

   For example, an implementation of a state machine may spend a
   significant amount of time in a particular state for performing the
   procedure defined for the state without returning a response.  If
   such an implementation is made on a multithreading system, the
   procedure may be performed in a separate thread so that the
   implementation can perform appropriate action to deal with the case
   without blocking on the state for a long time (or forever if the
   procedure never completes due to, e.g., a non-responding user or a
   bug in an application callback function.)

   The following states are identified as the possible places of
   blocking:

   o  IDENTITY state in the peer state machine.  It may take some time
      to process Identity request when a user input is needed for
      obtaining an identity from the user.  The user may never input an
      identity.  An implementation may define an additional state
      transition from IDENTITY state to FAILURE state so that
      authentication can fail if no identity is obtained from the user
      before ClientTimeout timer expires.

   o  METHOD state in the peer state machine and in METHOD_RESPONSE
      state in the authenticator state machines.  It may take some time
      to perform method-specific procedures in these states.  An
      implementation may define an additional state transition from
      METHOD state and METHOD_RESPONSE state to FAILURE or
      TIMEOUT_FAILURE state so that authentication can fail if no method
      processing result is obtained from the method before methodTimeout
      timer expires.

8.2.  Method/Method and Method/Lower-Layer Interfaces

   Implementations may define additional interfaces to pass method-
   specific information between methods and lower layers.  These
   interfaces are beyond the scope of this document.








Vollbrecht, et al.            Informational                    [Page 36]

Internet-Draft             EAP State Machines             September 2004


9.  Security Considerations

   This document's intent is to describe the EAP state machine fully.
   To this end, any security concerns with this document are likely a
   reflection of security concerns with EAP itself.

   An accurate state machine can help reduce implementation errors.
   While [RFC3748] remains the normative protocol description, this
   state machine should help in this regard.

   As noted in [RFC3748], there are some security concerns that arise
   because of the following EAP packets:

      1. EAP-Request/Response Identity
      2. EAP-Response/NAK
      3. EAP-Success/Failure

   Since these packets are not cryptographically protected by
   themselves, an attacker can modify or insert them without immediate
   detection by the peer or authenticator.

   Following Figure 3 specification, an attacker may cause denial of
   service by:

   o  Sending an EAP-Failure to the peer before the peer has started an
      EAP authentication method.  As long as the peer has not modified
      the methodState variable (initialized to NONE), the peer MUST
      accept an EAP-Failure.

   o  Forcing the peer to engage in endless EAP-Request/Response
      Identity exchanges before it has started an EAP authentication
      method.  As long as the peer has not modified the selectedMethod
      variable (initialized to NONE), the peer MUST accept an EAP-
      Request/Identity and respond to it with an EAP-Response/ Identity.

   Following Figure 4 specification, an attacker may cause denial of
   service by:

   o  Sending a NAK to the authenticator after the authenticator first
      proposes an EAP authentication method to the peer.  When the
      methodState variable has the value PROPOSED, the authenticator is
      obliged to process a NAK that is received in response to its first
      packet of an EAP authentication method.

   There MAY be some cases when it is desired to prevent such attacks.
   This can be done by modifying initial values of some variables of the
   EAP state machines.  However, such modifications are NOT RECOMMENDED.




Vollbrecht, et al.            Informational                    [Page 37]

Internet-Draft             EAP State Machines             September 2004


   There is a trade-off between mitigating these denial of service
   attacks and being able to deal with EAP peers and authenticators in
   general.  For instance, should the sending of a NAK to the
   authenticator after it has just proposed an EAP authentication method
   to the peer be ignored, then a legitimate peer that is not able or
   willing to process the proposed EAP authentication method would fail
   without an opportunity to negotiate another EAP method.

10.  Acknowledgments

   The work in this document was done as part of the EAP Design Team.
   It was done primarily by Nick Petroni, John Vollbrecht, Pasi Eronen
   and Yoshihiro Ohba.  Nick started this work with Bryan Payne and Chuk
   Seng at the University of Maryland.  John Vollbrecht, of Vollbrecht
   Consulting, started independently with help from Dave Spence at
   Interlink Networks.  John and Nick combined to create a common
   document, and then were joined by Pasi Eronen of Nokia who has made
   major contributions in creating coherent state machines, and
   Yoshihiro Ohba of Toshiba who insisted on including Pass-Through
   documentation and provided significant support for understanding
   implementation issues.

   In addition significant response and conversation has come from the
   design team, especially including Jari Arkko of Ericsson and Bernard
   Aboba of Microsoft as well as the rest of the team.  It has also been
   passed through the 802.1aa group, and has had input from Jim Burns of
   Meetinghouse and Paul Congdon of Hewlett Packard.

11.  References

11.1.  Normative References

   [RFC2119]   Bradner, S., "Key words for use in RFCs to Indicate
               Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3579]   Aboba, B. and P. Calhoun, "RADIUS (Remote Authentication
               Dial In User Service) Support For Extensible
               Authentication Protocol (EAP)", RFC 3579, September 2003.

   [RFC3748]   Aboba, B., Blunk, L., Vollbrecht, J., Carlson, J., and H.
               Levkowetz, Ed., "Extensible Authentication Protocol
               (EAP)", RFC 3748, June 2004.

11.2.  Informative References

   [Keying]    Aboba, B., Simon, D., Arkko, J., Eronen, P., Levkowetz,
               H., "Extensible Authentication Protocol (EAP) Key
               Management Framework", Work in Progress, July 2004.



Vollbrecht, et al.            Informational                    [Page 38]

Internet-Draft             EAP State Machines             September 2004


   [1X-REV]    Institute of Electrical and Electronics Engineers, "DRAFT
               Standard for Local and Metropolitan Area Networks: Port-
               Based Network Access Control (Revision)", IEEE 802-1X-
               REV/D11, July 2004.















































Vollbrecht, et al.            Informational                    [Page 39]

Internet-Draft             EAP State Machines             September 2004


Appendix A. ASCII versions of state diagrams

   This appendix contains the state diagrams in ASCII format.  Please
   use the PDF version whenever possible: it is much easier to
   understand.

   The notation is as follows: state name and pseudocode executed when
   entering it are shown on the left; outgoing transitions with their
   conditions are shown on the right.

A.1.  EAP Peer State Machine (Figure 3)

---------------------------------------------------------------------
(global transitions)         |      !portEnabled      |      DISABLED
                             |------------------------+--------------
                             |     eapRestart &&      |    INITIALIZE
                             |      portEnabled       |
-----------------------------+------------------------+--------------
DISABLED                     |      portEnabled       |    INITIALIZE
-----------------------------+------------------------+--------------
INITIALIZE                   |                        |
                             |                        |
selectedMethod = NONE        |                        |
methodState = NONE           |                        |
allowNotifications = TRUE    |                        |
decision = FAIL              |          UCT           |          IDLE
idleWhile = ClientTimeout    |                        |
lastId = NONE                |                        |
eapSuccess = FALSE           |                        |
eapFail = FALSE              |                        |
eapKeyData = NONE            |                        |
eapKeyAvailable = FALSE      |                        |
eapRestart = FALSE           |                        |
-----------------------------+------------------------+--------------
IDLE                         |         eapReq         |      RECEIVED
                             |------------------------+--------------
                             |     (altAccept &&      |
                             |  decision != FAIL) ||  |
                             |   (idleWhile == 0 &&   |       SUCCESS
                             |      decision ==       |
                             |      UNCOND_SUCC)      |
                             |------------------------+--------------









Vollbrecht, et al.            Informational                    [Page 40]

Internet-Draft             EAP State Machines             September 2004


                             |------------------------+--------------
                             |      altReject ||      |
                             |   (idleWhile == 0 &&   |
                             |      decision !=       |
                             |    UNCOND_SUCC) ||     |       FAILURE
                             |     (altAccept &&      |
                             | methodState != CONT && |
                             |   decision == FAIL)    |
-----------------------------+------------------------+--------------
RECEIVED                     |        rxReq &&        |        METHOD
                             |  (reqId != lastId) &&  |
(rxReq,rxSuccess,rxFailure,  |     (reqMethod ==      |
  reqId,reqMethod) =         |   selectedMethod) &&   |
  parseEapReq(eapReqData)    | (methodState != DONE)  |
                             |------------------------+--------------
                             |        rxReq &&        |
                             |  (reqId != lastId) &&  |
                             |   (selectedMethod ==   |
                             |        NONE) &&        |    GET_METHOD
                             |     (reqMethod !=      |
                             |      IDENTITY) &&      |
                             |     (reqMethod !=      |
                             |     NOTIFICATION)      |
                             |------------------------+--------------
                             |        rxReq &&        |
                             |  (reqId != lastId) &&  |
                             |   (selectedMethod ==   |      IDENTITY
                             |        NONE) &&        |
                             |     (reqMethod ==      |
                             |       IDENTITY)        |
                             |------------------------+--------------
                             |        rxReq &&        |
                             |  (reqId != lastId) &&  |
                             |   (reqMethod ==        |  NOTIFICATION
                             |    NOTIFICATION) &&    |
                             |   allowNotifications   |
                             |------------------------+--------------
                             |        rxReq &&        |    RETRANSMIT
                             |   (reqId == lastId)    |
                             |------------------------+--------------
                             |      rxSuccess &&      |
                             |  (reqId == lastId) &&  |       SUCCESS
                             |   (decision != FAIL)   |
                             |------------------------+--------------







Vollbrecht, et al.            Informational                    [Page 41]

Internet-Draft             EAP State Machines             September 2004


                             |------------------------+--------------
                             | (methodState!=CONT) && |
                             |     ((rxFailure &&     |
                             |      decision !=       |
                             |    UNCOND_SUCC) ||     |       FAILURE
                             |     (rxSuccess &&      |
                             | decision == FAIL)) &&  |
                             |   (reqId == lastId)    |
                             |------------------------+--------------
                             |          else          |       DISCARD
-----------------------------+------------------------+--------------
METHOD                       |                        |
                             |                        |
ignore = m.check(eapReqData) |         ignore         |       DISCARD
if (!ignore) {               |                        |
  (methodState, decision,    |                        |
  allowNotifications) =      |------------------------+--------------
  m.process(eapReqData)      |                        |
  /* methodState is CONT,    |                        |
     MAY_CONT, or DONE */    | (methodState==DONE) && |       FAILURE
  /* decision is FAIL,       |   (decision == FAIL)   |
     COND_SUCC, or           |                        |
     UNCOND_SUCC */          |                        |
  eapRespData =              |------------------------+--------------
    m.buildResp(reqId)       |                        |
  if (m.isKeyAvailable())    |          else          | SEND_RESPONSE
    eapKeyData = m.getKey()  |                        |
}                            |                        |
-----------------------------+------------------------+--------------
GET_METHOD                   |                        |
                             |   selectedMethod ==    |
if (allowMethod(reqMethod)) {|       reqMethod        |        METHOD
  selectedMethod = reqMethod |                        |
  methodState = INIT         |                        |
} else {                     |------------------------+--------------
  eapRespData =              |                        |
    buildNak(reqId)          |          else          | SEND_RESPONSE
}                            |                        |
-----------------------------+------------------------+--------------
IDENTITY                     |                        |
                             |                        |
processIdentity(eapReqData)  |          UCT           | SEND_RESPONSE
eapRespData =                |                        |
  buildIdentity(reqId)       |                        |
-----------------------------+------------------------+--------------






Vollbrecht, et al.            Informational                    [Page 42]

Internet-Draft             EAP State Machines             September 2004


-----------------------------+------------------------+--------------
NOTIFICATION                 |                        |
                             |                        |
processNotify(eapReqData)    |          UCT           | SEND_RESPONSE
eapRespData =                |                        |
  buildNotify(reqId)         |                        |
-----------------------------+------------------------+--------------
RETRANSMIT                   |                        |
                             |          UCT           | SEND_RESPONSE
eapRespData = lastRespData   |                        |
-----------------------------+------------------------+--------------
DISCARD                      |                        |
                             |          UCT           |          IDLE
eapReq = FALSE               |                        |
eapNoResp = TRUE             |                        |
-----------------------------+------------------------+--------------
SEND_RESPONSE                |                        |
                             |                        |
lastId = reqId               |                        |
lastRespData = eapRespData   |          UCT           |          IDLE
eapReq = FALSE               |                        |
eapResp = TRUE               |                        |
idleWhile = ClientTimeout    |                        |
-----------------------------+------------------------+--------------
SUCCESS                      |                        |
                             |                        |
if (eapKeyData != NONE)      |                        |
  eapKeyAvailable = TRUE     |                        |
eapSuccess = TRUE            |                        |
-----------------------------+------------------------+--------------
FAILURE                      |                        |
                             |                        |
eapFail = TRUE               |                        |
---------------------------------------------------------------------
                                Figure 8

A.2.  EAP Standalone Authenticator State Machine (Figure 4)

---------------------------------------------------------------------
(global transitions)          |    !portEnabled     |        DISABLED
                              |---------------------+----------------
                              |    eapRestart &&    |      INITIALIZE
                              |     portEnabled     |
------------------------------+---------------------+----------------
DISABLED                      |     portEnabled     |      INITIALIZE
------------------------------+---------------------+----------------





Vollbrecht, et al.            Informational                    [Page 43]

Internet-Draft             EAP State Machines             September 2004


------------------------------+---------------------+----------------
INITIALIZE                    |                     |
                              |                     |
currentId = NONE              |                     |
eapSuccess = FALSE            |                     |
eapFail = FALSE               |         UCT         |   SELECT_ACTION
eapTimeout = FALSE            |                     |
eapKeyData = NONE             |                     |
eapKeyAvailable = FALSE       |                     |
eapRestart = FALSE            |                     |
------------------------------+---------------------+----------------
IDLE                          |                     |
                              |  retransWhile == 0  |      RETRANSMIT
retransWhile =                |                     |
  calculateTimeout(           |---------------------+----------------
   retransCount, eapSRTT,     |       eapResp       |        RECEIVED
   eapRTTVAR, methodTimeout)  |                     |
------------------------------+---------------------+----------------
RETRANSMIT                    |                     |
                              |   retransCount >    | TIMEOUT_FAILURE
retransCount++                |     MaxRetrans      |
if (retransCount<=MaxRetrans){|                     |
  eapReqData = lastReqData    |---------------------+----------------
  eapReq = TRUE               |        else         |            IDLE
}                             |                     |
------------------------------+---------------------+----------------
RECEIVED                      |      rxResp &&      |
                              |     (respId ==      |
(rxResp,respId,respMethod)=   |    currentId) &&    |
  parseEapResp(eapRespData)   | (respMethod == NAK  |
                              |         ||          |             NAK
                              |    respMethod ==    |
                              |  EXPANDED_NAK) &&   |
                              |   (methodState ==   |
                              |      PROPOSED)      |
                              |---------------------+----------------
                              |      rxResp &&      |
                              |     (respId ==      |
                              |    currentId) &&    | INTEGRITY_CHECK
                              |   (respMethod ==    |
                              |   currentMethod)    |
                              |---------------------+----------------
                              |        else         |         DISCARD
------------------------------+---------------------+----------------







Vollbrecht, et al.            Informational                    [Page 44]

Internet-Draft             EAP State Machines             September 2004


------------------------------+---------------------+----------------
NAK                           |                     |
                              |         UCT         |   SELECT_ACTION
m.reset()                     |                     |
Policy.update(<...>)          |                     |
------------------------------+---------------------+----------------
SELECT_ACTION                 | decision == FAILURE |         FAILURE
                              |                     |
decision =                    |---------------------+----------------
  Policy.getDecision()        | decision == SUCCESS |         SUCCESS
/* SUCCESS, FAILURE, or       |---------------------+----------------
   CONTINUE */                |        else         |  PROPOSE_METHOD
------------------------------+---------------------+----------------
INTEGRITY_CHECK               |       ignore        |         DISCARD
                              |---------------------+----------------
ignore = m.check(eapRespData) |       !ignore       | METHOD_RESPONSE
------------------------------+---------------------+----------------
METHOD_RESPONSE               |                     |
                              | methodState == END  |   SELECT_ACTION
m.process(eapRespData)        |                     |
if (m.isDone()) {             |                     |
  Policy.update(<...>)        |---------------------+----------------
  eapKeyData = m.getKey()     |                     |
  methodState = END           |        else         |  METHOD_REQUEST
} else                        |                     |
  methodState = CONTINUE      |                     |
------------------------------+---------------------+----------------
PROPOSE_METHOD                |                     |
                              |                     |
currentMethod =               |                     |
  Policy.getNextMethod()      |                     |
m.init()                      |         UCT         |  METHOD_REQUEST
if (currentMethod==IDENTITY |||                     |
  currentMethod==NOTIFICATION)|                     |
  methodState = CONTINUE      |                     |
else                          |                     |
  methodState = PROPOSED      |                     |
------------------------------+---------------------+----------------
METHOD_REQUEST                |                     |
                              |                     |
currentId = nextId(currentId) |         UCT         |    SEND_REQUEST
eapReqData =                  |                     |
  m.buildReq(currentId)       |                     |
methodTimeout = m.getTimeout()|                     |
------------------------------+---------------------+----------------






Vollbrecht, et al.            Informational                    [Page 45]

Internet-Draft             EAP State Machines             September 2004


------------------------------+---------------------+----------------
DISCARD                       |                     |
                              |         UCT         |            IDLE
eapResp = FALSE               |                     |
eapNoReq = TRUE               |                     |
------------------------------+---------------------+----------------
SEND_REQUEST                  |                     |
                              |                     |
retransCount = 0              |         UCT         |            IDLE
lastReqData = eapReqData      |                     |
eapResp = FALSE               |                     |
eapReq = TRUE                 |                     |
------------------------------+---------------------+----------------
TIMEOUT_FAILURE               |                     |
                              |                     |
eapTimeout = TRUE             |                     |
------------------------------+---------------------+----------------
FAILURE                       |                     |
                              |                     |
eapReqData =                  |                     |
  buildFailure(currentId)     |                     |
eapFail = TRUE                |                     |
------------------------------+---------------------+----------------
SUCCESS                       |                     |
                              |                     |
eapReqData =                  |                     |
  buildSuccess(currentId)     |                     |
if (eapKeyData != NONE)       |                     |
  eapKeyAvailable = TRUE      |                     |
eapSuccess = TRUE             |                     |
---------------------------------------------------------------------
                                Figure 9

A.3.  EAP Backend Authenticator State Machine (Figure 5)

---------------------------------------------------------------------
(global transitions)          |   !backendEnabled   |        DISABLED
------------------------------+---------------------+----------------
DISABLED                      |  backendEnabled &&  |      INITIALIZE
                              |     aaaEapResp      |
------------------------------+---------------------+----------------










Vollbrecht, et al.            Informational                    [Page 46]

Internet-Draft             EAP State Machines             September 2004


------------------------------+---------------------+----------------
INITIALIZE                    |       !rxResp       |   SELECT_ACTION
                              |---------------------+----------------
currentMethod = NONE          |      rxResp &&      |
(rxResp,respId,respMethod)=   | (respMethod == NAK  |
  parseEapResp(aaaEapRespData)|         ||          |             NAK
if (rxResp)                   |    respMethod ==    |
  currentId = respId          |    EXPANDED_NAK)    |
else                          |---------------------+----------------
  currentId = NONE            |        else         |  PICK_UP_METHOD
------------------------------+---------------------+----------------
PICK_UP_METHOD                |                     |
                              |  currentMethod ==   |   SELECT_ACTION
if (Policy.doPickUp(          |        NONE         |
    respMethod)) {            |                     |
  currentMethod = respMethod  |---------------------+----------------
  m.initPickUp()              |        else         | METHOD_RESPONSE
}                             |                     |
------------------------------+---------------------+----------------
IDLE                          |     aaaEapResp      |        RECEIVED
------------------------------+---------------------+----------------
RECEIVED                      |      rxResp &&      |
                              |     (respId ==      |
(rxResp,respId,respMethod)=   |    currentId) &&    |
  parseEapResp(aaaEapRespData)| (respMethod == NAK  |
                              |         ||          |             NAK
                              |    respMethod ==    |
                              |  EXPANDED_NAK) &&   |
                              |   (methodState ==   |
                              |      PROPOSED)      |
                              |---------------------+----------------
                              |      rxResp &&      |
                              |     (respId ==      |
                              |    currentId) &&    | INTEGRITY_CHECK
                              |   (respMethod ==    |
                              |   currentMethod)    |
                              |---------------------+----------------
                              |        else         |         DISCARD
------------------------------+---------------------+----------------
NAK                           |                     |
                              |         UCT         |   SELECT_ACTION
m.reset()                     |                     |
Policy.update(<...>)          |                     |
------------------------------+---------------------+----------------







Vollbrecht, et al.            Informational                    [Page 47]

Internet-Draft             EAP State Machines             September 2004


------------------------------+---------------------+----------------
SELECT_ACTION                 | decision == FAILURE |         FAILURE
                              |                     |
decision =                    |---------------------+----------------
  Policy.getDecision()        | decision == SUCCESS |         SUCCESS
/* SUCCESS, FAILURE, or       |---------------------+----------------
   CONTINUE */                |        else         |  PROPOSE_METHOD
------------------------------+---------------------+----------------
INTEGRITY_CHECK               |       ignore        |         DISCARD
                              |                     |
ignore =                      |---------------------+----------------
  m.check(aaaEapRespData)     |       !ignore       | METHOD_RESPONSE
------------------------------+---------------------+----------------
METHOD_RESPONSE               |                     |
                              | methodState == END  |   SELECT_ACTION
m.process(aaaEapRespData)     |                     |
if (m.isDone()) {             |                     |
  Policy.update(<...>)        |---------------------+----------------
  aaaEapKeyData = m.getKey()  |                     |
  methodState = END           |        else         |  METHOD_REQUEST
} else                        |                     |
  methodState = CONTINUE      |                     |
------------------------------+---------------------+----------------
PROPOSE_METHOD                |                     |
                              |                     |
currentMethod =               |                     |
  Policy.getNextMethod()      |                     |
m.init()                      |         UCT         |  METHOD_REQUEST
if (currentMethod==IDENTITY |||                     |
  currentMethod==NOTIFICATION)|                     |
  methodState = CONTINUE      |                     |
else                          |                     |
  methodState = PROPOSED      |                     |
------------------------------+---------------------+----------------
METHOD_REQUEST                |                     |
                              |                     |
currentId = nextId(currentId) |                     |
aaaEapReqData =               |         UCT         |    SEND_REQUEST
  m.buildReq(currentId)       |                     |
aaaMethodTimeout =            |                     |
  m.getTimeout()              |                     |
------------------------------+---------------------+----------------
DISCARD                       |                     |
                              |         UCT         |            IDLE
aaaEapResp = FALSE            |                     |
aaaEapNoReq = TRUE            |                     |
------------------------------+---------------------+----------------




Vollbrecht, et al.            Informational                    [Page 48]

Internet-Draft             EAP State Machines             September 2004


------------------------------+---------------------+----------------
SEND_REQUEST                  |                     |
                              |         UCT         |            IDLE
aaaEapResp = FALSE            |                     |
aaaEapReq = TRUE              |                     |
------------------------------+---------------------+----------------
FAILURE                       |                     |
                              |                     |
aaaEapReqData =               |                     |
  buildFailure(currentId)     |                     |
aaaEapFail = TRUE             |                     |
------------------------------+---------------------+----------------
SUCCESS                       |                     |
                              |                     |
aaaEapReqData =               |                     |
  buildSuccess(currentId)     |                     |
if (aaaEapKeyData != NONE)    |                     |
  aaaEapKeyAvailable = TRUE   |                     |
aaaEapSuccess = TRUE          |                     |
---------------------------------------------------------------------
                               Figure 10

A.4.  EAP Full Authenticator State Machine (Figures 6 and 7)

   This state machine contains all the states from EAP Standalone
   Authenticator State Machine, except that SELECT_ACTION state is
   replaced with the following:

---------------------------------------------------------------------
SELECT_ACTION                 | decision == FAILURE |         FAILURE
                              |                     |
decision =                    |---------------------+----------------
  Policy.getDecision()        | decision == SUCCESS |         SUCCESS
/* SUCCESS, FAILURE, CONTINUE,|---------------------+----------------
   or PASSTHROUGH */          |     decision ==     |     INITIALIZE_
                              |     PASSTHROUGH     |     PASSTHROUGH
                              |---------------------+----------------
                              |        else         |  PROPOSE_METHOD
---------------------------------------------------------------------
                               Figure 11

And the following new states are added:

---------------------------------------------------------------------
INITIALIZE_PASSTHROUGH        |  currentId != NONE  |     AAA_REQUEST
                              |---------------------+----------------
aaaEapRespData = NONE         |  currentId == NONE  |        AAA_IDLE
------------------------------+---------------------+----------------



Vollbrecht, et al.            Informational                    [Page 49]

Internet-Draft             EAP State Machines             September 2004


------------------------------+---------------------+----------------
IDLE2                         |                     |
                              |  retransWhile == 0  |     RETRANSMIT2
retransWhile =                |                     |
  calculateTimeout(           |---------------------+----------------
   retransCount, eapSRTT,     |       eapResp       |       RECEIVED2
   eapRTTVAR, methodTimeout)  |                     |
------------------------------+---------------------+----------------
RETRANSMIT2                   |                     |
                              |   retransCount >    |        TIMEOUT_
retransCount++                |     MaxRetrans      |        FAILURE2
if (retransCount<=MaxRetrans){|                     |
  eapReqData = lastReqData    |---------------------+----------------
  eapReq = TRUE               |        else         |           IDLE2
}                             |                     |
------------------------------+---------------------+----------------
RECEIVED2                     |      rxResp &&      |
                              |     (respId ==      |     AAA_REQUEST
(rxResp,respId,respMethod)=   |     currentId)      |
  parseEapResp(eapRespData)   |---------------------+----------------
                              |        else         |        DISCARD2
------------------------------+---------------------+----------------
AAA_REQUEST                   |                     |
                              |                     |
if (respMethod == IDENTITY) { |         UCT         |        AAA_IDLE
  aaaIdentity = eapRespData   |                     |
aaaEapRespData = eapRespData  |                     |
------------------------------+---------------------+----------------
AAA_IDLE                      |     aaaEapNoReq     |        DISCARD2
                              |---------------------+----------------
aaaFail = FALSE               |      aaaEapReq      |    AAA_RESPONSE
aaaSuccess = FALSE            |---------------------+----------------
aaaEapReq = FALSE             |     aaaTimeout      |        TIMEOUT_
aaaEapNoReq = FALSE           |                     |        FAILURE2
aaaEapResp = TRUE             |---------------------+----------------
                              |       aaaFail       |        FAILURE2
                              |---------------------+----------------
                              |     aaaSuccess      |        SUCCESS2
------------------------------+---------------------+----------------
AAA_RESPONSE                  |                     |
                              |                     |
eapReqData = aaaEapReqData    |         UCT         |   SEND_REQUEST2
currentId = getId(eapReqData) |                     |
methodTimeout =               |                     |
  aaaMethodTimeout            |                     |
------------------------------+---------------------+----------------





Vollbrecht, et al.            Informational                    [Page 50]

Internet-Draft             EAP State Machines             September 2004


------------------------------+---------------------+----------------
DISCARD2                      |                     |
                              |         UCT         |           IDLE2
eapResp = FALSE               |                     |
eapNoReq = TRUE               |                     |
------------------------------+---------------------+----------------
SEND_REQUEST2                 |                     |
                              |                     |
retransCount = 0              |         UCT         |           IDLE2
lastReqData = eapReqData      |                     |
eapResp = FALSE               |                     |
eapReq = TRUE                 |                     |
------------------------------+---------------------+----------------
TIMEOUT_FAILURE2              |                     |
                              |                     |
eapTimeout = TRUE             |                     |
------------------------------+---------------------+----------------
FAILURE2                      |                     |
                              |                     |
eapReqData = aaaEapReqData    |                     |
eapFail = TRUE                |                     |
------------------------------+---------------------+----------------
SUCCESS2                      |                     |
                              |                     |
eapReqData = aaaEapReqData    |                     |
eapKeyData = aaaEapKeyData    |                     |
eapKeyAvailable =             |                     |
  aaaEapKeyAvailable          |                     |
eapSuccess = TRUE             |                     |
---------------------------------------------------------------------
                               Figure 12




















Vollbrecht, et al.            Informational                    [Page 51]

Internet-Draft             EAP State Machines             September 2004


Authors' Addresses

   John R. Vollbrecht
   Vollbrecht Consulting LLC
   9682 Alice Hill Drive
   Dexter, MI  48130
   USA

   EMail: jrv@umich.edu


   Pasi Eronen
   Nokia Research Center
   P.O. Box 407
   FIN-00045 Nokia Group,
   Finland

   EMail: pasi.eronen@nokia.com


   Nick L. Petroni, Jr.
   University of Maryland, College Park
   A.V. Williams Building
   College Park, MD  20742
   USA

   EMail: npetroni@cs.umd.edu


   Yoshihiro Ohba
   Toshiba America Research, Inc.
   1 Telcordia Drive
   Piscataway, NJ  08854
   USA

   EMail: yohba@tari.toshiba.com















Vollbrecht, et al.            Informational                    [Page 52]

Internet-Draft             EAP State Machines             September 2004


Full Copyright Statement

   Copyright (C) The Internet Society (2004).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/S HE
   REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE
   INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR
   IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the IETF's procedures with respect to rights in IETF Documents can
   be found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at ietf-
   ipr@ietf.org.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.







Vollbrecht, et al.            Informational                    [Page 53]


Html markup produced by rfcmarkup 1.109, available from https://tools.ietf.org/tools/rfcmarkup/