[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: (draft-polk-geopriv-dhcp-lbyr-uri-option) 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15

Network WG                                                   James Polk
Internet-Draft                                            Cisco Systems
Intended status: Proposed Standard                         Mar 12, 2012
Expires: Sept 12, 2012


        Dynamic Host Configuration Protocol (DHCP) IPv4 and IPv6
         Option for a Location Uniform Resource Identifier (URI)
              draft-ietf-geopriv-dhcp-lbyr-uri-option-14


Abstract

   This document creates a Dynamic Host Configuration Protocol (DHCP)
   Option for transmitting a client's geolocation Uniform Resource
   Identifier (URI). This Location URI can then be dereferenced in a
   separate transaction by the client or sent to another entity and
   dereferenced to learn physically where the client is located.


Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six
   months and may be updated, replaced, or obsoleted by other documents
   at any time.  It is inappropriate to use Internet-Drafts as
   reference material or to cite them other than as "work in progress."

   This Internet-Draft will expire on September 12, 2012.

Copyright Notice

   Copyright (c) 2011 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with
   respect to this document.  Code Components extracted from this
   document must include Simplified BSD License text as described in
   Section 4.e of the Trust Legal Provisions and are provided without
   warranty as described in the Simplified BSD License.





Polk                    Expires Sept 12, 2012                  [Page 1]

Internet-Draft     Geopriv DHCP Location URI Option            Mar 2012


Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .  2
   2.  Format of the DHCP LocationURI Option . . . . . . . . . . . .  4
       2.1.  Overall Format of LocationURI Option in IPv4  . . . . .  4
       2.2.  Overall Format of LocationURI Option in IPv6  . . . . .  5
       2.3.  LocationURI Format for both IPv4 and IPv6 . . . . . . .  5
   3.  DHCP Option Operation . . . . . . . . . . . . . . . . . . . .  6
       3.1 Architectural Assumptions . . . . . . . . . . . . . . . .  8
       3.2 Harmful URIs and URLs . . . . . . . . . . . . . . . . . .  8
       3.3 Valid Location URI Schemes or Types . . . . . . . . . . .  9
   4.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  9
   5.  Security Considerations . . . . . . . . . . . . . . . . . . . 10
   6.  Acknowledgements  . . . . . . . . . . . . . . . . . . . . . . 11
   7.  References  . . . . . . . . . . . . . . . . . . . . . . . . . 12
       7.1. Normative References . . . . . . . . . . . . . . . . . . 12
       7.2. Informative References . . . . . . . . . . . . . . . . . 12
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . . 13


   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].


1.  Introduction

   This document creates a Dynamic Host Configuration Protocol (DHCP)
   Option for transmitting a client's geolocation Uniform Resource
   Identifier (URI). The DHCP implementation of the client can then
   make this location information available to upper layer protocols
   for their usage.  This location URI points a Location Server
   [RFC5808] which has the geolocation of the client (through means
   not defined in this document).  In this scenario, the DHCP client
   is a Geopriv Target (i.e., the entity whose geolocation is
   associated with the location URI).

   Applications using upper layer protocols within the Target can then
   choose to deference this location URI and/or transmit the URI to
   another entity as a means of conveying where the Target is located.
   Dereferencing a location URI is described in [RFC6442]. Conveying
   a location URI is also described in [RFC6442]. Session Initiation
   Protocol (SIP) is not the only protocol that can dereference a
   location URI; there is also HTTP-Enabled Location Delivery (HELD)
   [ID-HELD-DEREF] and HTTP [RFC2616].

   Having a location URI has advantages over having a PIDF-LO,
   especially when a target's location changes.  With a location URI,
   when a target moves, the location URI does not change (at least
   within the same domain). It can still be given out as the reference
   to the Target's current location. The opposite is true if the


Polk                    Expires Sept 12, 2012                  [Page 2]

Internet-Draft     Geopriv DHCP Location URI Option            Mar 2012

   location is conveyed by value in a message. Once the Target moves,
   the previously given location is no longer valid, and if the Target
   wants to inform another entity about its location, it has to send
   the PIDF-LO to the location recipient (again).

   A Location Server (LS) stores the Target's location as a presence
   document, called a Presence Information Data Format - Location
   Object (PIDF-LO), defined in RFC 4119 [RFC4119]. The Location Server
   is the entity contacted during the act of dereferencing a Target's
   location.  If the dereferencing entity has permission, defined in
   [ID-GEO-POL], the location of the target will be received.  The LS
   will grant permission to location inquires based on the rules
   established by a Rule Holder [RFC3693].  The LS has the ability to
   challenge any request for a target's location, thereby providing
   additive security properties before location revelation.

   A problem exists within existing RFCs that provide location to the
   UA ([RFC3825] and [RFC4776]). These DHCP Options for geolocation
   values require an update of the entire location information (LI)
   every time a client moves.  Not all clients will move frequently,
   but some will.  Refreshing location values every time a client moves
   does not scale in certain networks/environments, such as IP-based
   cellular networks, enterprise networks or service provider networks
   with mobile endpoints.  An 802.11 based access network is one
   example of this. Constantly updating LCI to endpoints might not
   scale in mobile (residential or enterprise or municipal) networks in
   which the client is moving through more than one network attachment
   point, perhaps as a person walks or drives with their client down a
   neighborhood street or apartment complex or a shopping center or
   through a municipality (that has IP connectivity as a service).

   If the client was provided a location URI reference to retain and
   hand out when it wants or needs to convey its location (in a
   protocol other than DHCP), a location URI that would not change as
   the client's location changes (within a domain), scaling issues
   would be significantly reduced to needing an update of the location
   URI only when a client changes administrative domains - which is
   much less often.  This delivery of an indirect location has the
   added benefit of not using up valuable or limited bandwidth to the
   client with the constant updates.  It also relieves the client from
   having to determine when it has moved far enough to consider asking
   for a refresh of its location.

   In enterprise networks, if a known location is assigned to each
   individual Ethernet port in the network, a device that attaches to
   the network a wall-jack (directly associated with a specific
   Ethernet Switch port) will be associated with a known location via a
   unique circuit-ID that's used by the RAIO Option defined in RFC 3046
   [RFC3046].  This assumes wall-jacks have an updated wiremap
   database.  RFC 3825 and RFC 4776 would return an LCI value of
   location.  This document specifies how a location URI is returned
   using DHCP.  The location URI points to a PIDF-LO contained on an


Polk                    Expires Sept 12, 2012                  [Page 3]

Internet-Draft     Geopriv DHCP Location URI Option            Mar 2012

   LS. Performing a dereferencing transaction, that Target's PIDF-LO
   will be returned.  If local configuration has the requirement of
   only assigning unique location URIs to each client at the same
   attachment point to the network (i.e., same RJ-45 jack or same
   802.11 Access Point - except when triangulation is used), then
   unique location URIs will be given out, though they will all have
   the same location at the record, relieving the backend Sighter or LS
   from individually maintaining each location independently.

   This Option can be useful in IEEE 802.16e connected endpoints or IP
   cellular endpoints.  The location URI Option can be configured on a
   router, such as a residential home gateway, such that the router
   receives this Location URI Option as a client with the ability to
   communicate to downstream endpoints as a server.

   How an LS responds to a dereference request can vary, and a policy
   established by a Ruleholder [RFC3693] for a Location Target as to
   what type of challenge(s) is to be used, how strong a challenge is
   used or how precise the location information is given to a
   Location Recipient (LR). This document does not provide mechanisms
   for the LS to tell the client about policies or for the client to
   specify a policy for the LS. While an LS should apply an appropriate
   access-control policy, clients must assume that the LS will provide
   location in response to any request (following the possession model
   [RFC5808]).  For further discussion of privacy, see the Security
   Considerations.

   This document IANA-registers the new IPv4 and IPv6 DHCP Options for
   a location URI.


2.  Format of the DHCP LocationURI Option


2.1 Overall Format of LocationURI Option in IPv4

   The LocationURI Option format for IPv4 is as follows:

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |   Code XXX    |   Length=XX   |                               .
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+                               .
    .                         LocationURI...                       ...
    .                  (see Section 2.3 for details) ...            |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

    Figure 1. IPv4 Fields for this LocationURI Option

   Code XXX:  The code for this DHCPv4 option (IANA assigned).

   Length=XX: The length of this option, counted in bytes - not


Polk                    Expires Sept 12, 2012                  [Page 4]

Internet-Draft     Geopriv DHCP Location URI Option            Mar 2012

              counting the Code and Length bytes. This is a variable
              length Option, therefore the length value will change
              based on the length of the URI within the Option.

   LocationURI: see Section 2.3 for details


2.2 Overall Format of LocationURI Option in IPv6

   The LocationURI Option format for IPv6 is as follows:

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |          option-code          |           option-len          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                        LocationURI...                         .
    .                 (see Section 2.3 for details)                 |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

    Figure 2. IPv6 fields of this LocationURI Option

   option-code: The code for this DHCPv6 option (IANA assigned).

   option-len:  The length of this option, counted in bytes - not
                counting the Code and Length bytes. This is a variable
                length Option, therefore the length value will change
                based on the length of the URI within the Option.

   LocationURI: see below (Section 2.3 for details).


2.3 LocationURI Format for both IPv4 and IPv6

   The LocationURI, in both DHCPv4 and DHCPv6, have the following
   format:


     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |    LuriType    |   LuriLength   |   LuriValue                ...
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

    Figure 3. LocationURI TLV Format for both IPv4 and IPv6

      LuriType:   A one-byte identifier of the data location value.

      LuriLength: The length of the LuriValue, not including the
                  LuriLength field itself, up to a maximum of 255
                  units. The unit of measurement is defined by the
                  LuriType field definition. The LuriLength itself is


Polk                    Expires Sept 12, 2012                  [Page 5]

Internet-Draft     Geopriv DHCP Location URI Option            Mar 2012

                  always a one-byte unsigned integer.

      LuriValue:  The LocationURI value, as described in detail below.

   The LuriTypes this document defines for a point are:

      LuriType=1 Location URI - This field, in bytes, is the URI
                 pointing at the location record where the PIDF-LO for
                 the Location Target resides. The LuriValue of
                 LuriType=1 is always represented in UTF-8.

      LuriType=2 Valid-For - The time, in seconds, this URI is to be
                 considered Valid for dereferencing. The timer
                 associated with this LuriType starts upon receipt of
                 this Option by the client. The LuriValue of LuriType=2
                 is always represented as a four-byte unsigned integer.

   The Valid-For (LuriType=2) indicates how long, in seconds, the
   client is to consider this location URI (LuriType=1) valid.
   Applications MUST NOT make use of a location URI after it becomes
   invalid (i.e., after the Valid-For timer expires).

   The choice of the Valid-For value is a policy decision for the
   operator of the DHCP server.  Like location URIs themselves, it can
   be statically configured on the DHCP server or provisioned
   dynamically (via an out-of-band exchange with a Location Information
   Server) as requests for location URIs are received.

   The Valid-For timer is used only at the application layer, as an
   indication of when the URI can be used to access location.  It is
   independent of the DHCP lease timer, and in no way related to the
   DHCP state machine.  Clients MUST NOT trigger an automatic DHCP
   refresh on expiry of the Valid-For timer; rather, they should follow
   normal DCHP mechanics.

   Server operators should consider the relation between the Valid-For
   time and the lease time.  Clients typically request a lease refresh
   when half the lease time is up. If the Valid-For time is less than
   the typical refresh rate (i.e., half the lease time), then for the
   remaining interval, clients will run the risk of not having a usable
   location URI for applications.  If the Valid-For time is less than
   half the typical refresh rate, it is a near certainty clients will
   not have a usable location URI for the interval between the
   Valid-For time and the typical refresh time for applications.

   For example, if a lease is set to 24 hours, the typical refresh
   request is set to initiate at the 12 hour mark. If the Valid-For
   timer is set to less than 24 hours, but more than 12 hours (in this
   example), the client might not be refreshed at the 12 hour mark and
   runs the risk of not have a location URI for applications that
   request it.  If, on the other hand, the Valid-For timer is less than
   12 hours (in this example, which is before a typical client would


Polk                    Expires Sept 12, 2012                  [Page 6]

Internet-Draft     Geopriv DHCP Location URI Option            Mar 2012

   ask for a refresh, applications will be without a usable location
   URI until the full refresh has been received.

   It should be expected that clients will overwrite any previous
   Option values when receiving a new instance of that Option number.

   The Valid-For (LuriType=2) offers no meaningful information without
   an accompanying Location URI (LuriType=1), therefore a Valid-For
   (LuriType=2) MUST NOT be sent without a Location URI (LuriType=1).

   The Valid-For (LuriType=2) is not mandated for use by this document.
   However, its presence MUST NOT cause any error in handling the
   location URI (i.e., if not understood, it MUST be ignored).

   This Option format is highly extensible. Additional LuriType types
   created MUST be done so through IANA registration with a standards
   track RFC.


3. DHCP Option Operation

   The [RFC3046] RAIO can be utilized to provide the appropriate
   indication to the DHCP Server where this DISCOVER or REQUEST message
   came from, in order to supply the correct response.

   Caution SHOULD always be used involving the creation of large
   Options, meaning that this Option MAY need to be in its own INFORM,
   OPTION or ACK message.

   It is RECOMMENDED to avoid building URIs, with any parameters,
   larger than what a single DHCP response can be.  However, if a
   message is larger than 255 bytes, concatenation is allowed, per RFC
   3396 [RFC3396].

   Per [RFC2131], subsequent LocationURI Options, which are
   non-concatenated, overwrite the previous value.

   Location URIs MUST NOT reveal identity information of the user of
   the device, since DHCP is a cleartext delivery protocol. For
   example, creating a location URI such as

      sips:34LKJH534663J54@example.com

   is better than a location URI such as

      sips:aliceisat123mainstalantageorgiaus@example.com

   The username portion of the first example URI provides no direct
   identity information (in which 34LKJH534663J54 is considered to be a
   random number in this example).

   In the <presence> element of a PIDF-LO document, there is an


Polk                    Expires Sept 12, 2012                  [Page 7]

Internet-Draft     Geopriv DHCP Location URI Option            Mar 2012

   'entity' attribute that identities what entity *this* document
   (including the associated location) refers to.  It is up to the
   PIDF-LO generator, either Location Server or an application in the
   endpoint, to insert the identity in the 'entity' attribute.  This
   can be seen in [RFC4119].  The considerations for populating the
   entity attribute value in a PIDF-LO document are independent from
   the considerations for avoiding exposing identification information
   in the username part of a location URI.


   This Option is used only for communications between a DHCP client
   and a DHCP server.  It can be solicited (requested) by the client,
   or it can be pushed by the server without a request for it.  DHCP
   Options not understood MUST be ignored [RFC2131].  A DHCP server
   supporting this Option might or might not have the location of a
   client.  If a server does not have a client's location, but needs to
   provide this Location URI Option to a client (for whatever reason),
   an LS is contacted.  This server-to-LS transaction is not DHCP,
   therefore it is out of scope of this document. Note that this
   server-to-LS transaction could delay the DHCP messaging to the
   client. If the server fails to have location before it transmits its
   message to the client, location will not be part of that DHCP
   message. Any timers involved here are a matter of local
   configuration.

   The deference of a target's location URI would not involve DHCP, but
   an application layer protocol, such as SIP or HTTP, therefore
   dereferencing is out of scope of this document.

   In the case of residential gateways being DHCP servers, they usually
   perform as DHCP clients in a hierarchical fashion up into a service
   provider's network DHCP server(s), or learn what information to
   provide via DHCP to residential clients through a protocol, such as
   PPP.  In these cases, the location URI would likely indicate the
   residence's civic address to all wired or wireless clients within
   that residence.


3.1 Architectural Assumptions

   The following assumptions have been made for use of this LocationURI
   Option for a client to learn its location URI (in no particular
   order):

   o  Any user control (what [RFC3693] calls a 'Ruleholder') for access
      to the dereferencing step is assumed to be out of scope of this
      document. An example authorization policy is in [ID-GEO-POL].

   o  The authorization vs. possession security model can be found in
      [RFC5808], describing what is expected in each model of
      operation.  It should be assumed that a location URI attained
      using DHCP will operate under an possession model by default.


Polk                    Expires Sept 12, 2012                  [Page 8]

Internet-Draft     Geopriv DHCP Location URI Option            Mar 2012

      An authorization model can be instituted as a matter of local
      policy.  An authorization model means possessing the location URI
      does not give that entity the right to view the PIDF-LO of the
      target whose location is indicated in a presence document.  The
      dereference transaction will be challenged by the Location Server
      only in an authorization model.  The nature of this challenge is
      out of scope of this document.

   o  This document does not prevent some environments from operating
      in an authorization model, for example - in less tightly
      controlled networks. The costs associated with authorization vs.
      possession models are discussed in Section 3.3.2 of [RFC5606].


3.2 Harmful URIs and URLs

   There are, in fact, some types of URIs that are not good to receive,
   due to security concerns.  For example, any URLs that can have
   scripts, such as "data:" URLs, and some "HTTP:" URLs that go to web
   pages that have scripts.  Therefore,

   o URIs received via this Option MUST NOT be automatically sent to a
     general-browser to connect to a web page, because they could have
     harmful scripts.

   o This Option MUST NOT contain "data:" URLs, because they could
     contain harmful scripts.

   Instead of listing all the types of URIs and URLs that can be
   misused or potentially have harmful affects, Section 3.3 IANA
   registers acceptable location URI schemes (or types).


3.3  Valid Location URI Schemes or Types

   This section specifies which URI types are acceptable as a location
   URI scheme (or type) for this DHCP Option:

   1. sip:
   2. sips:
   3. pres:
   4. http:
   5. https:

   URIs using the "pres" scheme are dereferenced using the presence
   event package for SIP [RFC3856], so they will reference a PIDF-LO
   document when location is available.  Responses to requests for URIs
   with other schemes ("sip", "sips", "http", and "https") MUST have
   MIME type 'application/pidf+xml'.  Alternatively, HTTP and HTTPS
   URIs MAY refer to information with MIME type 'application/held+xml',
   in order to support HELD dereferencing [ID-HELD-DEREF].  Clients can
   indicate which MIME types they support using the "Accept" header


Polk                    Expires Sept 12, 2012                  [Page 9]

Internet-Draft     Geopriv DHCP Location URI Option            Mar 2012

   field in SIP [RFC3261] or HTTP [RFC2616].

   See RFC 3922 [RFC3922] for using the pres: URI with XMPP.

   It is RECOMMENDED that implementers follow Section 4.6 of RFC 6442
   [RFC6442] as guidance regarding which Location URI schemes to
   provide in DHCP. That document discusses what a receiving entity
   does when receiving a URI scheme that is not understood. Awareness
   to the two URI types there is important for conveying location, if
   SIP is used to convey a Location URI provided by DHCP.


4.  IANA Considerations

4.1 The IPv4 Option number for this Option

   This document IANA registers this IPv4 Option number XXX (to be
   assigned by IANA once this document becomes an RFC).


4.2 The IPv6 Option-Code for this Option

   This document IANA registers this IPv6 Option-Code XXX (to be
   assigned by IANA once this document becomes an RFC).


4.3 IANA Considerations for LuriTypes

   IANA is requested to create a new registry for acceptable location
   types defined in Section 3.2 of this document, arranged similar to
   this:

   +------------+----------------------------------------+-----------+
   |  LuriType  |   Name                                 | Reference |
   +------------+----------------------------------------+-----------+
   |     1      |   Location URI                         | RFC XXXX* |
   |     2      |   Valid-For                            | RFC XXXX* |
   +------------+----------------------------------------+-----------+

    * RFC XXXX is to be replaced with this document's RFC-Editor RFC
      number.

   Additions to this registry require a standards track RFC.


5.  Security Considerations

   Where critical decisions might be based on the value of this
   location URI option, DHCP authentication in [RFC3118] SHOULD be used
   to protect the integrity of the DHCP options.

   A real concern with RFC 3118 it is that not widely deployed because


Polk                    Expires Sept 12, 2012                 [Page 10]

Internet-Draft     Geopriv DHCP Location URI Option            Mar 2012

   it requires pre-shared keys to successfully work (i.e., in the
   client and in the server).  Most implementations do not
   accommodate this.

   DHCP, initially, is a broadcast request (a client looking for a
   server), and a unicast response (answer from a server) type of
   protocol.  It does not provide security at the network layer.
   Instead, it relies on lower-layer security mechanisms.

   Once a client has a URI, it needs information on how the location
   server will control access to dereference requests.  A client might
   treat a tightly access-controlled URI differently from one that can
   be dereferenced by anyone on the Internet (i.e., one following the
   "possession model").  With the LuriTypes defined in this document,
   the DHCP option for delivering location URIs can only tell the user
   how long the URI will be valid.  Since the client does not know what
   policy will be applied during this validity interval, clients MUST
   handle location URIs as if they could be dereferenced by anybody
   until they expire.  For example, such open location URIs should only
   be transmitted in encrypted channels.  Nonetheless, location servers
   SHOULD apply appropriate access control policies, for example by
   limiting the number of queries that any given client can make, or
   limiting access to users within an enterprise.

   Extensions to this option, such as [ID-POLICY-URI] can provide
   mechanisms for accessing and provisioning policy.  Giving users
   access to policy information will allow them to make more informed
   decisions about how to use their location URIs.  Allowing users to
   provide policy information to the LS will enable them to tailor
   access control policies to their needs (within the bounds of policy
   that the LS will accept).

   As to the concerns about the location URI itself, as stated in the
   document (see Section 3), it MUST NOT have any user identifying
   information in the URI user-part/string itself.  The location URI
   also needs to be hard to guess that it belongs to a specific user.

   When implementing a DHCP server that will serve clients across an
   uncontrolled network, one should consider the potential security
   risks therein.


6.  Acknowledgements

   Thanks to James Winterbottom, Marc Linsner, Roger Marshall and
   Robert Sparks for their useful comments. And to Lisa Dusseault for
   her concerns about the types of URIs that can cause harm.  To
   Richard Barnes for inspiring a more robust Security Considerations
   section, and for offering the text to incorporate HTTP URIs.  To
   Hannes Tschofenig and Ted Hardie for riding me to comply with their
   concerns, including a good scrubbing of the nearly final doc.



Polk                    Expires Sept 12, 2012                 [Page 11]

Internet-Draft     Geopriv DHCP Location URI Option            Mar 2012

7.  References

7.1.  Normative References

 [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
           Requirement Levels", BCP 14, RFC 2119, March 1997.

 [RFC2131] Droms, R., "Dynamic Host Configuration Protocol", RFC 2131,
           March 1997.

 [RFC3046] Patrick, M., "DHCP Relay Agent Information Option", RFC
           3046, January 2001.

 [RFC3118] Droms, R. and W. Arbaugh, "Authentication for DHCP
           Messages", RFC 3118, June 2001.

 [RFC3261] J. Rosenberg, H. Schulzrinne, G. Camarillo, A. Johnston, J.
           Peterson, R. Sparks, M. Handley, and E. Schooler, "SIP:
           Session Initiation Protocol", RFC 3261, May 2002.

 [RFC3396] T. Lemon, S. Cheshire, "Encoding Long Options in the Dynamic
           Host Configuration Protocol (DHCPv4)", RFC 3396, November
           2002

 [RFC3856] J. Rosenberg, "A Presence Event Package for the Session
           Initiation Protocol (SIP)", RFC 3856, August 2004

 [RFC3922] P. Saint-Andre, " Mapping the Extensible Messaging and
           Presence Protocol (XMPP) to Common Presence and Instant
           Messaging (CPIM)", RFC 3922, October 2004

 [RFC4119] J. Peterson, "A Presence-based GEOPRIV Location Object
           Format", RFC 4119, December 2005

 [RFC5808] R. Marshall, Ed., "Requirements for a Location-by-Reference
           Mechanism", RFC 5808, May 2010

 [RFC6442] Polk, J., Rosen, B., and J. Peterson, "Location Conveyance
           for the Session Initiation Protocol", RFC 6442, December
           2011.


7.2.  Informative References

 [RFC2616] R. Fielding, J. Gettys, J., Mogul, H. Frystyk, L.,
           Masinter, P. Leach, T. Berners-Lee, "Hypertext Transfer
           Protocol - HTTP/1.1", RFC 2616, June 1999

 [RFC3693] J. Cuellar, J. Morris, D. Mulligan, J. Peterson. J. Polk,
           "Geopriv Requirements", RFC 3693, February 2004

 [RFC3825] J. Polk, J. Schnizlein, M. Linsner, "Dynamic Host


Polk                    Expires Sept 12, 2012                 [Page 12]

Internet-Draft     Geopriv DHCP Location URI Option            Mar 2012

           Configuration Protocol Option for Coordinate-based Location
           Configuration Information", RFC 3825, July 2004

 [RFC4776] H. Schulzrinne, "Dynamic Host Configuration Protocol
           (DHCPv4 and DHCPv6) Option for Civic Addresses Configuration
           Information ", RFC 4776, November 2006

 [RFC5606] J. Peterson, T. Hardie, J. Morris, "Implications of
           'retransmission-allowed' for SIP Location Conveyance",
           August 2009

 [RFC5808] R. Marshall, "Requirements for a Location-by-Reference
           Mechanism", RFC 5808, May 2010

 [ID-HELD-DEREF] J. Winterbottom, H. Tschofenig, H. Schulzrinne, M.
           Thomson, M. Dawson, "A Location Dereferencing Protocol Using
           HELD", "work in progress", October 2011

 [ID-GEO-POL] H. Schulzrinne, H. Tschofenig, J. Morris, J. Cuellar, J.
           Polk, "Geolocation Policy: A Document Format for Expressing
           Privacy Preferences for Location Information", "work in
           progress", October 2011

 [ID-POLICY-URI] R. Barnes, M. Thomson, J. Winterbottom, "Location
           Configuration Extensions for Policy Management", "work in
           progress", November 2011


Authors' Address

   James Polk
   3913 Treemont Circle
   Colleyville, Texas 76034
   USA

   Email: jmpolk@cisco.com


















Polk                    Expires Sept 12, 2012                 [Page 13]

Html markup produced by rfcmarkup 1.109, available from https://tools.ietf.org/tools/rfcmarkup/