[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 RFC 2617

HTTP Working Group                  J. Franks, Northwestern University
INTERNET DRAFT                         P. Hallam-Baker, Verisign, Inc.
<draft-ietf-http-authentication-03>      J. Hostetler, AbiSource, Inc.
                                            S. Lawrence, Agranat, Inc.
                                       P. Leach, Microsoft Corporation
                      A. Luotonen, Netscape Communications Corporation
                                         L. Stewart, Open Market, Inc.
Expires: March 2, 1999                              September 2, 1998



      HTTP Authentication: Basic and Digest Access Authentication




Status of this Memo

This document is an Internet-Draft. Internet-Drafts are working
documents of the Internet Engineering Task Force (IETF), its areas, and
its working groups. Note that other groups may also distribute working
documents as Internet-Drafts.

Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or made obsolete by other documents at any
time. It is inappropriate to use Internet-Drafts as reference material
or to cite them other than as "work in progress".

To learn the current status of any Internet-Draft, please check the
"1id-abstracts.txt" listing contained in the Internet-Drafts Shadow
Directories on ftp.is.co.za (Africa), nic.nordu.net (Europe),
munnari.oz.au (Pacific Rim), or ftp.isi.edu (US West Coast).

Distribution of this document is unlimited. Please send comments to the
HTTP working group at <http-wg@hplb.hpl.hp.com>. Discussions of the
working group are archived at
<URL:http://www.ics.uci.edu/pub/ietf/http/>.

Copyright NoticeCopyright (C) The Internet Society (1998). All Rights
Reserved. See section 9 for the full copyright notice.




Abstract

'HTTP/1.0' includes the specification for a Basic Access Authentication
scheme. This scheme is not considered to be a secure method of user
authentication (unless used in conjunction with some external secure
system such as SSL [5]), as the user name and password are passed over
the network as cleartext.

This document also provides the specification for HTTP's authentication
framework, the original Basic authentication scheme and a scheme based
on cryptographic hashes, referred to as 'Digest Access Authentication'.
It is therefore also intended to serve as a replacement for RFC 2069
[6].  Some optional elements specified by RFC 2069 have been removed
from this specification due to problems found since its publication;
other new elements have been added -for compatibility, those new
elements have been made optional, but are strongly recommended.



INTERNET-DRAFT      HTTP Authentication            09/02/98

Like Basic, Digest access authentication verifies that both parties to a
communication know a shared secret (a password); unlike Basic, this
verification can be done without sending the password in the clear,
which is Basic's biggest weakness. As with most other authentication
protocols, the greatest sources of risks are usually found not in the
core protocol itself but in policies and procedures surrounding its use.



















































Franks, et al.                                      [Page 2]

INTERNET-DRAFT      HTTP Authentication            09/02/98


Table of Contents



HTTP AUTHENTICATION: BASIC AND DIGEST ACCESS AUTHENTICATION1

Status of this Memo........................................1

Abstract...................................................1

Table of Contents..........................................3

1   Access Authentication.................................5
 1.1   Reliance on the HTTP/1.1 Specification............5
 1.2   Access Authentication Framework...................5

2   Basic Authentication Scheme...........................7

3   Digest Access Authentication Scheme...................8
 3.1   Introduction......................................8
  3.1.1  Purpose.........................................8
  3.1.2  Overall Operation...............................8
  3.1.3  Representation of digest values.................8
  3.1.4  Limitations.....................................8
 3.2   Specification of Digest Headers...................9
  3.2.1  The WWW-Authenticate Response Header............9
  3.2.2  The Authorization Request Header...............11
  3.2.3  The Authentication-Info Header.................16
 3.3   Digest Operation.................................17
 3.4   Security Protocol Negotiation....................18
 3.5   Example..........................................18
 3.6   Proxy-Authentication and Proxy-Authorization.....19

4   Security Considerations..............................19
 4.1   Authentication of Clients using Basic Authentication    19
 4.2   Authentication of Clients using Digest Authentication   20
 4.3   Limited Use Nonce Values.........................21
 4.4   Comparison of Digest with Basic Authentication...21
 4.5   Replay Attacks...................................21
 4.6   Weakness Created by Multiple Authentication Schemes22
 4.7   Online dictionary attacks........................23
 4.8   Man in the Middle................................23
 4.9   Chosen plaintext attacks.........................23
 4.10  Precomputed dictionary attacks...................24
 4.11  Batch brute force attacks........................24
 4.12  Spoofing by Counterfeit Servers..................24
 4.13  Storing passwords................................24
 4.14  Summary..........................................25

5   Sample implementation................................25

6   Acknowledgments......................................29

7   References...........................................29

8   Authors' Addresses...................................30

Franks, et al.                                      [Page 3]

INTERNET-DRAFT      HTTP Authentication            09/02/98

9   Full Copyright Statement.............................31
























































Franks, et al.                                      [Page 4]

INTERNET-DRAFT      HTTP Authentication            09/02/98

1 Access Authentication

1.1 Reliance on the HTTP/1.1 Specification

This specification is a companion to the HTTP/1.1 specification [2]. It
uses the augmented BNF section 2.1 of that document, and relies on both
the non-terminals defined in that document and other aspects of the
HTTP/1.1 specification.

1.2 Access Authentication Framework

HTTP provides a simple challenge-response authentication mechanism that
MAY be used by a server to challenge a client request and by a client to
provide authentication information. It uses an extensible, case-
insensitive token to identify the authentication scheme, followed by a
comma-separated list of attribute-value pairs which carry the parameters
necessary for achieving authentication via that scheme.

       auth-scheme    = token
       auth-param     = token "=" ( token | quoted-string )


The 401 (Unauthorized) response message is used by an origin server to
challenge the authorization of a user agent. This response MUST include
a WWW-Authenticate header field containing at least one challenge
applicable to the requested resource. The 407 (Proxy Authentication
Required) response message is used by a proxy to challenge the
authorization of a client and MUST include a Proxy-Authenticate header
field containing at least one challenge applicable to the proxy for the
requested resource.

    challenge   = auth-scheme 1*SP 1#auth-param

Note: User agents will need to take special care in parsing the WWW-
Authenticate or Proxy-Authenticate header field value if it contains
more than one challenge, or if more than one WWW-Authenticate header
field is provided, since the contents of a challenge may itself contain
a comma-separated list of authentication parameters.

The authentication parameter realm is defined for all authentication
schemes:

    realm       = "realm" "=" realm-value
    realm-value = quoted-string


The realm directive (case-insensitive) is required for all
authentication schemes that issue a challenge. The realm value (case-
sensitive), in combination with the canonical root URL (the absoluteURI
for the server whose abs_path is empty; see section 5.1.2 of [2]) of the
server being accessed, defines the protection space. These realms allow
the protected resources on a server to be partitioned into a set of
protection spaces, each with its own authentication scheme and/or
authorization database. The realm value is a string, generally assigned
by the origin server, which may have additional semantics specific to


Franks, et al.                                      [Page 5]

INTERNET-DRAFT      HTTP Authentication            09/02/98

the authentication scheme. Note that there may be multiple challenges
with the same auth-scheme but different realms.

A user agent that wishes to authenticate itself with an origin server--
usually, but not necessarily, after receiving a 401 (Unauthorized)--MAY
do so by including an Authorization header field with the request. A
client that wishes to authenticate itself with a proxy--usually, but not
necessarily, after receiving a 407 (Proxy Authentication Required)--MAY
do so by including a Proxy-Authorization header field with the request.
Both the Authorization field value and the Proxy-Authorization field
value consist of credentials containing the authentication information
of the client for the realm of the resource being requested. The user
agent MUST choose to use one of the challenges with the strongest auth-
scheme it understands and request credentials from the user based upon
that challenge.

credentials = auth-scheme #auth-param

     Note that many browsers will only recognize Basic and will require
     that it be the first auth-scheme presented. Servers should only
     include Basic if it is minimally acceptable.

The protection space determines the domain over which credentials can be
automatically applied. If a prior request has been authorized, the same
credentials MAY be reused for all other requests within that protection
space for a period of time determined by the authentication scheme,
parameters, and/or user preference. Unless otherwise defined by the
authentication scheme, a single protection space cannot extend outside
the scope of its server.

If the origin server does not wish to accept the credentials sent with a
request, it SHOULD return a 401 (Unauthorized) response. The response
MUST include a WWW-Authenticate header field containing at least one
(possibly new) challenge applicable to the requested resource. If a
proxy does not accept the credentials sent with a request, it SHOULD
return a 407 (Proxy Authentication Required). The response MUST include
a Proxy-Authenticate header field containing a (possibly new) challenge
applicable to the proxy for the requested resource.

The HTTP protocol does not restrict applications to this simple
challenge-response mechanism for access authentication. Additional
mechanisms MAY be used, such as encryption at the transport level or via
message encapsulation, and with additional header fields specifying
authentication information. However, these additional mechanisms are not
defined by this specification.

Proxies MUST be completely transparent regarding user agent
authentication by origin servers. That is, they must forward the WWW-
Authenticate and Authorization headers untouched, and follow the rules
found in section 14.8 of [2]. Both the Proxy-Authenticate and the Proxy-
Authorization header fields are hop-by-hop headers (see section 13.5.1
of [2]).





Franks, et al.                                      [Page 6]

INTERNET-DRAFT      HTTP Authentication            09/02/98

2 Basic Authentication Scheme

The "basic" authentication scheme is based on the model that the client
must authenticate itself with a user-ID and a password for each realm.
The realm value should be considered an opaque string which can only be
compared for equality with other realms on that server. The server will
service the request only if it can validate the user-ID and password for
the protection space of the Request-URI. There are no optional
authentication parameters.

For Basic, the framework above is utilized as follows:

      challenge   = "Basic" realm
      credentials = "Basic" basic-credentials


Upon receipt of an unauthorized request for a URI within the protection
space, the origin server MAY respond with a challenge like the
following:

       WWW-Authenticate: Basic realm="WallyWorld"

where "WallyWorld" is the string assigned by the server to identify the
protection space of the Request-URI. A proxy may respond with the same
challenge using the Proxy-Authenticate header field.

To receive authorization, the client sends the userid and password,
separated by a single colon (":") character, within a base64                                                               [7                                                                                                                              ] encoded
string in the credentials.

       basic-credentials = base64-user-pass
       base64-user-pass  = <base64 [4] encoding of user-pass,
                        except not limited to 76 char/line>
       user-pass   = userid ":" password
       userid      = *<TEXT excluding ":">
       password    = *TEXT

Userids might be case sensitive.

If the user agent wishes to send the userid "Aladdin" and password "open
sesame", it would use the following header field:

       Authorization: Basic QWxhZGRpbjpvcGVuIHNlc2FtZQ==


A client SHOULD assume that all paths at or deeper than the depth of the
last symbolic element in the path field of the Request-URI also are
within the protection space specified by the Basic realm value of the
current challenge. A client MAY preemptively send the corresponding
Authorization header with requests for resources in that space without
receipt of another challenge from the server. Similarly, when a client
sends a request to a proxy, it may reuse a userid and password in the
Proxy-Authorization header field without receiving another challenge
from the proxy server. See section 4 for security considerations
associated with Basic authentication.


Franks, et al.                                      [Page 7]

INTERNET-DRAFT      HTTP Authentication            09/02/98

3 Digest Access Authentication Scheme

3.1 Introduction

3.1.1 Purpose

The protocol referred to as "HTTP/1.0" includes the specification for a
Basic Access Authentication scheme[1]. That scheme is not considered to
be a secure method of user authentication, as the user name and password
are passed over the network in an unencrypted form. This section
provides the specification for a scheme that does not send the password
in cleartext,  referred to as "Digest Access Authentication".

The Digest Access Authentication scheme is not intended to be a complete
answer to the need for security in the World Wide Web. This scheme
provides no encryption of message content. The intent is simply to
create an access authentication method that avoids the most serious
flaws of Basic authentication.

3.1.2 Overall Operation

Like Basic Access Authentication, the Digest scheme is based on a simple
challenge-response paradigm. The Digest scheme challenges using a nonce
value. A valid response contains a checksum (by default, the MD5
checksum) of the username, the password, the given nonce value, the HTTP
method, and the requested URI. In this way, the password is never sent
in the clear. Just as with the Basic scheme, the username and password
must be prearranged in some fashion not addressed by this document.

3.1.3 Representation of digest values

An optional header allows the server to specify the algorithm used to
create the checksum or digest. By default the MD5 algorithm is used and
that is the only algorithm described in this document.

For the purposes of this document, an MD5 digest of 128 bits is
represented as 32 ASCII printable characters. The bits in the 128 bit
digest are converted from most significant to least significant bit,
four bits at a time to their ASCII presentation as follows. Each four
bits is represented by its familiar hexadecimal notation from the
characters 0123456789abcdef. That is, binary 0000 gets represented by
the character '0', 0001, by '1', and so on up to the representation of
1111 as 'f'.

3.1.4 Limitations

The Digest authentication scheme described in this document suffers from
many known limitations. It is intended as a replacement for Basic
authentication and nothing more. It is a password-based system and (on
the server side) suffers from all the same problems of any password
system. In particular, no provision is made in this protocol for the
initial secure arrangement between user and server to establish the
user's password.

Users and implementors should be aware that this protocol is not as
secure as Kerberos, and not as secure as any client-side private-key

Franks, et al.                                      [Page 8]

INTERNET-DRAFT      HTTP Authentication            09/02/98

scheme. Nevertheless it is better than nothing, better than what is
commonly used with telnet and ftp, and better than Basic authentication.

3.2 Specification of Digest Headers

The Digest Access Authentication scheme is conceptually similar to the
Basic scheme. The formats of the modified WWW-Authenticate header line
and the Authorization header line are specified below. In addition, a
new header, Authentication-Info, is specified.

3.2.1 The WWW-Authenticate Response Header

If a server receives a request for an access-protected object, and an
acceptable Authorization header is not sent, the server responds with a
"401 Unauthorized" status code, and a WWW-Authenticate header as per the
framework defined above, which for the digest scheme is utilized as
follows:

     challenge        =  "Digest" digest-challenge

     digest-challenge  = 1#( realm | [ domain ] | nonce |
                         [ opaque ] |[ stale ] | [ algorithm ] |
                         [ qop-options ] | [auth-param] )


     domain            = "domain" "=" <"> URI ( 1*SP URI ) <">
     URI               = absoluteURI | abs_path
     nonce             = "nonce" "=" nonce-value
     nonce-value       = quoted-string
     opaque            = "opaque" "=" quoted-string
     stale             = "stale" "=" ( "true" | "false" )
     algorithm         = "algorithm" "=" ( "MD5" | "MD5-sess" |
                          token )
     qop-options       = "qop" "=" <"> 1#qop-value <">
     qop-value         = "auth" | "auth-int" | token


The meanings of the values of the directives used above are as follows:


realm
  A string to be displayed to users so they know which username and
  password to use. This string should contain at least the name of the
  host performing the authentication and might additionally indicate
  the collection of users who might have access. An example might be
  "registered_users@gotham.news.com".


domain
  A quoted, space-separated list of URIs, as specified in RFC XURI [7],
  that define the protection space.  If a URI is an abs_path, it is
  relative to the canonical root URL (see section 1.2 above) of the
  server being accessed. An absoluteURI in this list may refer to a
  different server than the one being accessed. The client can use this
  list to determine the set of URIs for which the same authentication
  information may be sent: any URI that has a URI in this list as a
  prefix (after both have been made absolute) may be assumed to be in

Franks, et al.                                      [Page 9]

INTERNET-DRAFT      HTTP Authentication            09/02/98

  the same protection space. If this directive is omitted or its value
  is empty, the client should assume that the protection space consists
  of all URIs on the responding server. This directive is not
  meaningful in Proxy-Authenticate headers, for which the protection
  space is always the entire proxy; if present it should be ignored.


nonce
  A server-specified data string which should be uniquely generated
  each time a 401 response is made. It is recommended that this string
  be base64 or hexadecimal data. Specifically, since the string is
  passed in the header lines as a quoted string, the double-quote
  character is not allowed.

  The contents of the nonce are implementation dependent. The quality
  of the implementation depends on a good choice. A nonce might, for
  example, be constructed as the base 64 encoding of

      time-stamp H(time-stamp ":" ETag ":" private-key)

  where time-stamp is a server-generated time or other non-repeating
  value, ETag is the value of the HTTP ETag header associated with the
  requested entity, and private-key is data known only to the server.
  With a nonce of this form a server would recalculate the hash portion
  after receiving the client authentication header and reject the
  request if it did not match the nonce from that header or if the
  time-stamp value is not recent enough. In this way the server can
  limit the time of the nonce's validity. The inclusion of the ETag
  prevents a replay request for an updated version of the resource.
  (Note: including the IP address of the client in the nonce would
  appear to offer the server the ability to limit the reuse of the
  nonce to the same client that originally got it. However, that would
  break proxy farms, where requests from a single user often go through
  different proxies in the farm. Also, IP address spoofing is not that
  hard.)


  An implementation might choose not to accept a previously used nonce
  or a previously used digest, in order to protect against a replay
  attack. Or, an implementation might choose to use one-time nonces or
  digests for POST or PUT requests and a time-stamp for GET requests.
  For more details on the issues involved see section 4. of this
  document.


  The nonce is opaque to the client.


opaque
  A string of data, specified by the server, which should be returned
  by the client unchanged in the Authorization header of subsequent
  requests with URIs in the same protection space. It is recommended
  that this string be base64 or hexadecimal data.


stale
  A flag, indicating that the previous request from the client was
  rejected because the nonce value was stale. If stale is TRUE (case-
  insensitive), the client may wish to simply retry the request with a
  new encrypted response, without reprompting the user for a new

Franks, et al.                                     [Page 10]

INTERNET-DRAFT      HTTP Authentication            09/02/98

  username and password. The server should only set stale to TRUE if it
  receives a request for which the nonce is invalid but with a valid
  digest for that nonce (indicating that the client knows the correct
  username/password). If stale is FALSE, or anything other than TRUE,
  or the stale directive is not present, the username and/or password
  are invalid, and new values must be obtained.


algorithm
  A string indicating a pair of algorithms used to produce the digest
  and a checksum. If this is not present it is assumed to be "MD5". If
  the algorithm is not understood, the challenge should be ignored (and
  a different one used, if there is more than one).


  In this document the string obtained by applying the digest algorithm
  to the data "data" with secret "secret" will be denoted by KD(secret,
  data), and the string obtained by applying the checksum algorithm to
  the data "data" will be denoted H(data). The notation unq(X) means
  the value of the quoted-string X without the surrounding quotes.



  For the "MD5" and "MD5-sess" algorithms

      H(data) = MD5(data)

  and

      KD(secret, data) = H(concat(secret, ":", data))

  i.e., the digest is the MD5 of the secret concatenated with a
  colon concatenated with the data. The "MD5-sess" algorithm is
  intended to allow efficient 3rd party authentication servers;
  for the difference in usage, see the description in section
  3.2.2.2.


qop-options
  This directive is optional, but is made so only for backward
  compatibility with RFC 2069 [6]; it SHOULD be used by all
  implementations compliant with this version of the Digest scheme.
  If present, it is a quoted string of one or more tokens indicating
  the "quality of protection" values supported by the server.  The
  value "auth" indicates authentication; the value "auth-int" indicates
  authentication with integrity protection; see the descriptions below
  for calculating the response directive value for the application of
  this choice. Unrecognized options MUST be ignored.


auth-param
  This directive allows for future extensions. Any unrecognized
  directive MUST be ignored.

3.2.2 The Authorization Request Header

The client is expected to retry the request, passing an
Authorization header line, which is defined according to the
framework above, utilized as follows.

    credentials      = "Digest" digest-response

Franks, et al.                                     [Page 11]

INTERNET-DRAFT      HTTP Authentication            09/02/98


    digest-response  = 1#( username | realm | nonce | digest-uri
                    | response | [ algorithm ] | [cnonce] |
                    [opaque] | [message-qop] |
                        [nonce-count]  | [auth-param] )

    username         = "username" "=" username-value
    username-value   = quoted-string
    digest-uri       = "uri" "=" digest-uri-value
    digest-uri-value = request-uri   ; As specified by HTTP/1.1
    message-qop      = "qop" "=" qop-value
    cnonce           = "cnonce" "=" cnonce-value
    cnonce-value     = nonce-value
    nonce-count      = "nc" "=" nc-value
    nc-value         = 8LHEX
    response         = "response" "=" request-digest
    request-digest = <"> 32LHEX <">
    LHEX             =  "0" | "1" | "2" | "3" |
                        "4" | "5" | "6" | "7" |
                        "8" | "9" | "a" | "b" |
                        "c" | "d" | "e" | "f"


The values of the opaque and algorithm fields must be those
supplied in the WWW-Authenticate response header for the entity
being requested.


response
  A string of 32 hex digits computed as defined below, which proves
  that the user knows a password


username
  The user's name in the specified realm.


digest-uri
  The URI from Request-URI of the Request-Line; duplicated here because
  proxies are allowed to change the Request-Line in transit.


qop
  Indicates what "quality of protection" the client has applied to the
  message. If present, its value MUST be one of the alternatives the
  server indicated it supports in the WWW-Authenticate header. These
  values affect the computation of the request-digest. Note that this
  is a single token, not a quoted list of alternatives as in WWW-
  Authenticate.  This directive is optional in order to preserve
  backward compatibility with a minimal implementation of RFC 2069 [6],
  but SHOULD be used if the server indicated that qop is supported by
  providing a qop directive in the WWW-Authenticate header field.


cnonce
  This MUST be specified if a qop directive is sent (see above), and
  MUST NOT be specified if the server did not send a qop directive in
  the WWW-Authenticate header field.  The cnonce-value is an opaque
  quoted string value provided by the client and used by both client

Franks, et al.                                     [Page 12]

INTERNET-DRAFT      HTTP Authentication            09/02/98

  and server to avoid chosen plaintext attacks, to provide mutual
  authentication, and to provide some message integrity protection.
  See the descriptions below of the calculation of the response-digest
  and request-digest values.


nonce-count
  This MUST be specified if a qop directive is sent (see above), and
  MUST NOT be specified if the server did not send a qop directive in
  the WWW-Authenticate header field.  The nc-value is the hexadecimal
  count of the number of requests (including the current request) that
  the client has sent with the nonce value in this request.  For
  example, in the first request sent in response to a given nonce
  value, the client sends "nc=00000001".  The purpose of this directive
  is to allow the server to detect request replays by maintaining its
  own copy of this count - if the same nc-value is seen twice, then the
  request is a replay.   See the description below of the construction
  of the request-digest value.


auth-param
  This directive allows for future extensions. Any unrecognized
  directive MUST be ignored.

If a directive or its value is improper, or required directives
are missing, the proper response is 400 Bad Request. If the
request-digest is invalid, then a login failure should be logged,
since repeated login failures from a single client may indicate
an attacker attempting to guess passwords.

The definition of request-digest above indicates the encoding for
its value. The following definitions show how the value is
computed.


3.2.2.1 Request-Digest

If the "qop" value is "auth" or "auth-int":

   request-digest  = <"> < KD ( H(A1),     unq(nonce-value)
                                       ":" nc-value
                                       ":" unq(cnonce-value)
                                       ":" unq(qop-value)
                                       ":" H(A2)
                               ) <">


If the "qop" directive is not present (this construction is for
compatibility with RFC 2069):

   request-digest  =
              <"> < KD ( H(A1), unq(nonce-value) ":" H(A2) ) >
<">

See below for the definitions for A1 and A2.

3.2.2.2 A1

Franks, et al.                                     [Page 13]

INTERNET-DRAFT      HTTP Authentication            09/02/98

If the "algorithm" directive's value is "MD5" or is unspecified, then A1
is:

   A1       = unq(username-value) ":" unq(realm-value) ":" passwd

where

   passwd   = < user's password >

If the "algorithm" directive's value is "MD5-sess", then A1 is
calculated only once - on the first request by the client
following receipt of a WWW-Authenticate challenge from the
server.  It uses the server nonce from that challenge, and the
first client nonce value to construct A1 as follows:

   A1       = H( unq(username-value) ":" unq(realm-value)
                  ":" passwd )
                  ":" unq(nonce-value) ":" unq(cnonce-value)

This creates a 'session key' for the authentication of subsequent
requests and responses which is different for each "authentication
session", thus limiting the amount of material hashed with any one key.
(Note: see further discussion of the authentication session in section
3.3.) Because the server need only use the hash of the user credentials
in order to create the A1 value, this construction could be used in
conjunction with a third party authentication service so that the web
server would not need the actual password value.  The specification of
such a protocol is beyond the scope of this specification.


3.2.2.3 A2

If the "qop" directive's value is "auth" or is unspecified, then A2 is:

   A2       = Method ":" digest-uri-value

If the "qop" value is "auth-int", then A2 is:

   A2       = Method ":" digest-uri-value ":" H(entity-body)


3.2.2.4 Directive values and quoted-string

Note that the value of many of the directives, such as "username-
value", are defined as a "quoted-string". However, the "unq"
notation indicates that surrounding quotation marks are removed
in forming the string A1. Thus if the Authorization header
includes the fields

  username="Mufasa", realm=myhost@testrealm.com

and the user Mufasa has password "Circle Of Life" then H(A1)
would be H(Mufasa:myhost@testrealm.com:Circle Of Life) with no
quotation marks in the digested string.



Franks, et al.                                     [Page 14]

INTERNET-DRAFT      HTTP Authentication            09/02/98

No white space is allowed in any of the strings to which the
digest function H() is applied unless that white space exists in
the quoted strings or entity body whose contents make up the
string to be digested. For example, the string A1 illustrated
above must be

     Mufasa:myhost@testrealm.com:Circle Of Life

with no white space on either side of the colons, but with the
white space between the words used in the password value.
Likewise, the other strings digested by H() must not have white
space on either side of the colons which delimit their fields
unless that white space was in the quoted strings or entity body
being digested.

Also note that if integrity protection is applied (qop=auth-int), the
H(entity-body) is the hash of the entity body, not the message body - it
is computed before any transfer encoding is applied by the sender and
after it has been removed by the recipient. Note that this includes
multipart boundaries and embedded headers in each part of any multipart
content-type.


3.2.2.5 Various considerations

The "Method" value is the HTTP request method as specified in
section 5.1.1 of [2]. The "request-uri" value is the Request-URI
from the request line as specified in section 5.1.2 of [2]. This
may be "*", an "absoluteURL" or an "abs_path" as specified in
section 5.1.2 of [2], but it MUST agree with the Request-URI. In
particular, it MUST be an "absoluteURL" if the Request-URI is an
"absoluteURL". The "cnonce-value" is an optional  client-chosen
value whose purpose is to foil chosen plaintext attacks.

The authenticating server must assure that the resource
designated by the "uri" directive is the same as the resource
specified in the Request-Line; if they are not, the server SHOULD
return a 400 Bad Request error. (Since this may be a symptom of
an attack, server implementers may want to consider logging such
errors.) The purpose of duplicating information from the request
URL in this field is to deal with the possibility that an
intermediate proxy may alter the client's Request-Line. This
altered (but presumably semantically equivalent) request would
not result in the same digest as that calculated by the client.

Implementers should be aware of how authenticated transactions
interact with shared caches. The HTTP/1.1 protocol specifies that
when a shared cache (see section 13.7 of [2]) has received a
request containing an Authorization header and a response from
relaying that request, it MUST NOT return that response as a
reply to any other request, unless one of two Cache-Control (see
section 14.9 of [2]) directives was present in the response. If
the original response included the "must-revalidate" Cache-
Control directive, the cache MAY use the entity of that response
in replying to a subsequent request, but MUST first revalidate it
with the origin server, using the request headers from the new

Franks, et al.                                     [Page 15]

INTERNET-DRAFT      HTTP Authentication            09/02/98

request to allow the origin server to authenticate the new
request. Alternatively, if the original response included the
"public" Cache-Control directive, the response entity MAY be
returned in reply to any subsequent request.

3.2.3 The Authentication-Info Header

The Authentication-Info header is used by the server to
communicate some information regarding the successful
authentication in the response.

     AuthenticationInfo = "Authentication-Info" ":" auth-info
     auth-info          = 1#(nextnonce | [ message-qop ]
                            | [ response-auth ] | [ cnonce ]
                            | [nonce-count] )
     nextnonce          = "nextnonce" "=" nonce-value
     response-auth      = "rspauth" "=" response-digest
     response-digest    = <"> *LHEX <">

The value of the nextnonce directive is the nonce the server
wishes the client to use for a future authentication response.
The server may send the Authentication-Info header with a
nextnonce field as a means of implementing one-time or otherwise
changing  nonces. If the nextnonce field is present the client
SHOULD use it when constructing the Authorization header for its
next request. Failure of the client to do so may result in a
request to re-authenticate from the server with the "stale=TRUE".

  Server implementations should carefully consider the
  performance implications of the use of this mechanism;
  pipelined requests will not be possible if every response
  includes a nextnonce directive that must be used on the next
  request received by the server.  Consideration should be given
  to the performance vs. security tradeoffs of allowing an old
  nonce value to be used for a limited time to permit request
  pipelining.  Use of the nonce-count can retain most of the
  security advantages of a new server nonce without the
  deleterious affects on pipelining.


message-qop
   Indicates the "quality of protection" options applied to the
  response by the server.  The value "auth" indicates authentication;
  the value "auth-int" indicates authentication with integrity
  protection. The server SHOULD use the same value for the message-qop
  directive in the response as was sent by the client in the
  corresponding request.

The optional response digest in the "response-auth" directive
supports mutual authentication -- the server proves that it knows
the user's secret, and with qop=auth-int also provides limited
integrity protection of the response. The "response-digest" value
is calculated as for the "request-digest" in the Authorization
header, except that if "qop=auth" or is not specified in the
Authorization header for the request, A2 is


Franks, et al.                                     [Page 16]

INTERNET-DRAFT      HTTP Authentication            09/02/98

   A2       = ":" digest-uri-value

and if "qop=auth-int", then A2 is

   A2       = ":" digest-uri-value ":" H(entity-body)

where "digest-uri-value" is the value of the "uri" directive on the
Authorization header in the request. The "cnonce-value" and "nc-value"
MUST be the ones for the client request to which this message is the
response. The "response-auth", "cnonce", and "nonce-count" directives
MUST BE present if "qop=auth" or "qop=auth-int" is specified.

The Authentication-Info header is allowed in the trailer of an
HTTP message transferred via chunked transfer-coding.

3.3 Digest Operation

Upon receiving the Authorization header, the server may check its
validity by looking up the password that corresponds to the
submitted username. Then, the server must perform the same digest
operation (e.g., MD5) performed by the client, and compare the
result to the given request-digest value.

Note that the HTTP server does not actually need to know the
user's cleartext password. As long as H(A1) is available to the
server, the validity of an Authorization header may be verified.

The client response to a WWW-Authenticate challenge for a
protection space starts an authentication session with that
protection space. The authentication session lasts until the
client receives another WWW-Authenticate challenge from any
server in the protection space. A client should remember the
username, password, nonce, nonce count and opaque values
associated with an authentication session to use to construct the
Authorization header in future requests within that protection
space. The Authorization header may be included preemptively;
doing so improves server efficiency and avoids extra round trips
for authentication challenges. The server may choose to accept
the old Authorization header information, even though the nonce
value included might not be fresh. Alternatively, the server may
return a 401 response with a new nonce value, causing the client
to retry the request; by specifying stale=TRUE with this
response, the server tells the client to retry with the new
nonce, but without prompting for a new username and password.

Because the client is required to return the value of the opaque
directive given to it by the server for the duration of a
session, the opaque data may be used to transport authentication
session state information. (Note that any such use can also be
accomplished more easily and safely by including the state in the
nonce.) For example, a server could be responsible for
authenticating content that actually sits on another server. It
would achieve this by having the first 401 response include a
domain directive whose value includes a URI on the second server,
and an opaque directive whose value contains the state
information. The client will retry the request, at which time the

Franks, et al.                                     [Page 17]

INTERNET-DRAFT      HTTP Authentication            09/02/98

server might respond with a 301/302 redirection, pointing to the
URI on the second server. The client will follow the redirection,
and pass an Authorization header , including the <opaque> data.

As with the basic scheme, proxies must be completely transparent
in the Digest access authentication scheme. That is, they must
forward the WWW-Authenticate, Authentication-Info and
Authorization headers untouched. If a proxy wants to authenticate
a client before a request is forwarded to the server, it can be
done using the Proxy-Authenticate and Proxy-Authorization headers
described in section 3.6 below.

3.4 Security Protocol Negotiation

It is useful for a server to be able to know which security
schemes a client is capable of handling.

It is possible that a server may want to require Digest as its
authentication method, even if the server does not know that the
client supports it. A client is encouraged to fail gracefully if
the server specifies only authentication schemes it cannot
handle.

3.5 Example

The following example assumes that an access-protected document
is being requested from the server via a GET request. The URI of
the document is "http://www.nowhere.org/dir/index.html". Both
client and server know that the username for this document is
"Mufasa", and the password is "Circle Of Life" (with one space
between each of the three words).

The first time the client requests the document, no Authorization
header is sent, so the server responds with:

      HTTP/1.1 401 Unauthorized
      WWW-Authenticate: Digest
              realm="testrealm@host.com",
              qop="auth,auth-int",
              nonce="dcd98b7102dd2f0e8b11d0f600bfb0c093",
              opaque="5ccc069c403ebaf9f0171e9517f40e41"


The client may prompt the user for the username and password,
after which it will respond with a new request, including the
following Authorization header:

      Authorization: Digest username="Mufasa",
              realm="testrealm@host.com",
              nonce="dcd98b7102dd2f0e8b11d0f600bfb0c093",
              uri="/dir/index.html",
              qop=auth,
              nc=00000001,
              cnonce="0a4f113b",
              response="6629fae49393a05397450978507c4ef1",
              opaque="5ccc069c403ebaf9f0171e9517f40e41"

Franks, et al.                                     [Page 18]

INTERNET-DRAFT      HTTP Authentication            09/02/98

3.6 Proxy-Authentication and Proxy-Authorization

The digest authentication scheme may also be used for
authenticating users to proxies, proxies to proxies, or proxies
to origin servers by use of the Proxy-Authenticate and Proxy-
Authorization headers. These headers are instances of the Proxy-
Authenticate and Proxy-Authorization headers specified in
sections 10.33 and 10.34 of the HTTP/1.1 specification [2] and
their behavior is subject to restrictions described there. The
transactions for proxy authentication are very similar to those
already described. Upon receiving a request which requires
authentication, the proxy/server must issue the "407 Proxy
Authentication Required" response with a "Proxy-Authenticate"
header.  The digest-challenge used in the Proxy-Authenticate
header is the same as that for the WWW-Authenticate header as
defined above in section 3.2.1.

The client/proxy must then re-issue the request with a Proxy-
Authorization header, with directives as specified for the Authorization
header in section 3.2.2 above.

On subsequent responses, the server sends Proxy-Authentication-Info with
directives the same as those for the Authentication-Info header field.

Note that in principle a client could be asked to authenticate
itself to both a proxy and an end-server, but never in the same
response.

4 Security Considerations


4.1 Authentication of Clients using Basic Authentication

The Basic authentication scheme is not a secure method of user
authentication, nor does it in any way protect the entity, which is
transmitted in cleartext across the physical network used as the
carrier. HTTP does not prevent additional authentication schemes and
encryption mechanisms from being employed to increase security or the
addition of enhancements (such as schemes to use one-time passwords) to
Basic authentication.

The most serious flaw in Basic authentication is that it results in the
essentially cleartext transmission of the user's password over the
physical network. It is this problem which Digest Authentication
attempts to address.

Because Basic authentication involves the cleartext transmission of
passwords it SHOULD NOT be used (without enhancements) to protect
sensitive or valuable information.

A common use of Basic authentication is for identification purposes --
requiring the user to provide a user name and password as a means of
identification, for example, for purposes of gathering accurate usage
statistics on a server. When used in this way it is tempting to think
that there is no danger in its use if illicit access to the protected
documents is not a major concern. This is only correct if the server

Franks, et al.                                     [Page 19]

INTERNET-DRAFT      HTTP Authentication            09/02/98

issues both user name and password to the users and in particular does
not allow the user to choose his or her own password. The danger arises
because naive users frequently reuse a single password to avoid the task
of maintaining multiple passwords.

If a server permits users to select their own passwords, then the threat
is not only unauthorized access to documents on the server but also
unauthorized access to any other resources on other systems that the
user protects with the same password. Furthermore, in the server's
password database, many of the passwords may also be users' passwords
for other sites. The owner or administrator of such a system could
therefore expose all users of the system to the risk of unauthorized
access to all those sites if this information is not maintained in a
secure fashion.

Basic Authentication is also vulnerable to spoofing by counterfeit
servers. If a user can be led to believe that he is connecting to a host
containing information protected by Basic authentication when, in fact,
he is connecting to a hostile server or gateway, then the attacker can
request a password, store it for later use, and feign an error. This
type of attack is not possible with Digest Authentication. Server
implementers SHOULD guard against the possibility of this sort of
counterfeiting by gateways or CGI scripts. In particular it is very
dangerous for a server to simply turn over a connection to a gateway.
That gateway can then use the persistent connection mechanism to engage
in multiple transactions with the client while impersonating the
original server in a way that is not detectable by the client.

4.2 Authentication of Clients using Digest Authentication

Digest Authentication does not provide a strong authentication
mechanism, when compared to public key based mechanisms, for
example. However, it is significantly stronger than (e.g.) CRAM-
MD5, which has been proposed for use with LDAP [10], POP and IMAP
(see RFC 2195 [9]).  It is intended to replace the much weaker
and even more dangerous Basic mechanism.

Digest Authentication offers no confidentiality protection beyond
protecting the actual password. All of the rest of the request
and response are available to an eavesdropper.

Digest Authentication offers only limited integrity protection
for the messages in either direction. If  qop=auth-int mechanism
is used, those parts of the message used in the calculation of
the WWW-Authenticate and Authorization header field response
directive values (see section 3.2 above) are  protected.  Most
header fields and their values could be modified as a part of a
man-in-the-middle attack.

Many needs for secure HTTP transactions cannot be met by Digest
Authentication. For those needs TLS or SHTTP are more appropriate
protocols. In particular Digest authentication cannot be used for
any transaction requiring confidentiality protection.
Nevertheless many functions remain for which Digest
authentication is both useful and appropriate.  Any service in


Franks, et al.                                     [Page 20]

INTERNET-DRAFT      HTTP Authentication            09/02/98

present use that uses Basic should be switched to Digest as soon
as practical.

4.3 Limited Use Nonce Values

The Digest scheme uses a server-specified nonce to seed the generation
of the request-digest value (as specified in section 3.2.2.1 above).  As
shown in the example nonce in section 3.2.1, the server is free to
construct the nonce such that it may only be used from a particular
client, for a particular resource, for a limited period of time or
number of uses, or any other restrictions.  Doing so strengthens the
protection provided against, for example, replay attacks (see 4.5).
However, it should be noted that the method chosen for generating and
checking the nonce also has performance and resource implications.  For
example, a server may choose to allow each nonce value to be used only
once by maintaining a record of whether or not each recently issued
nonce has been returned and sending a next-nonce directive in the
Authentication-Info header field of every response. This protects
against even an immediate replay attack, but has a high cost checking
nonce values, and perhaps more important will cause authentication
failures for any pipelined requests (presumably returning a stale nonce
indication).  Similarly, incorporating a request-specific element such
as the Etag value for a resource limits the use of the nonce to that
version of the resource and also defeats pipelining. Thus it may be
useful to do so for methods with side effects but have unacceptable
performance for those that do not.

4.4 Comparison of Digest with Basic Authentication

Both Digest and Basic Authentication are very much on the weak
end of the security strength spectrum. But a comparison between
the two points out the utility, even necessity, of replacing
Basic by Digest.

The greatest threat to the type of transactions for which these
protocols are used is network snooping. This kind of transaction
might involve, for example, online access to a database whose use
is restricted to paying subscribers. With Basic authentication an
eavesdropper can obtain the password of the user. This not only
permits him to access anything in the database, but, often worse,
will permit access to anything else the user protects with the
same password.

By contrast, with Digest Authentication the eavesdropper only gets
access to the transaction in question and not to the user's password.
The information gained by the eavesdropper would permit a replay attack,
but only with a request for the same document, and even that may be
limited by the server's choice of nonce.

4.5 Replay Attacks

A replay attack against Digest authentication would usually be
pointless for a simple GET request since an eavesdropper would
already have seen the only document he could obtain with a
replay. This is because the URI of the requested document is
digested in the client request and the server will only deliver

Franks, et al.                                     [Page 21]

INTERNET-DRAFT      HTTP Authentication            09/02/98

that document. By contrast under Basic Authentication once the
eavesdropper has the user's password, any document protected by
that password is open to him.

Thus, for some purposes, it is necessary to protect against
replay attacks. A good Digest implementation can do this in
various ways. The server created "nonce" value is implementation
dependent, but if it contains a digest of the client IP, a time-
stamp, the resource ETag, and a private server key (as
recommended above) then a replay attack is not simple. An
attacker must convince the server that the request is coming from
a false IP address and must cause the server to deliver the
document to an IP address different from the address to which it
believes it is sending the document. An attack can only succeed
in the period before the time-stamp expires. Digesting the client
IP and time-stamp in the nonce permits an implementation which
does not maintain state between transactions.

For applications where no possibility of replay attack can be
tolerated the server can use one-time nonce values which will not
be honored for a second use. This requires the overhead of the
server remembering which nonce values have been used until the
nonce time-stamp (and hence the digest built with it) has
expired, but it effectively protects against replay attacks.

An implementation must give special attention to the possibility
of replay attacks with POST and PUT requests. Unless the server
employs one-time or otherwise limited-use nonces and/or insists
on the use of the integrity protection of qop=auth-int, an
attacker could replay valid credentials from a successful request
with counterfeit form data or other message body. Even with the
use of integrity protection most metadata in header fields is not
protected. Proper nonce generation and checking provides some
protection against replay of previously used valid credentials,
but see 4.8.

4.6 Weakness Created by Multiple Authentication Schemes

An HTTP/1.1 server may return multiple challenges with a 401
(Authenticate) response, and each challenge may use a different auth-
scheme. A user agent MUST choose to use the strongest auth-scheme it
understands and request credentials from the user based upon that
challenge.

     Note that many browsers will only recognize Basic and will require
     that it be the first auth-scheme presented. Servers should only
     include Basic if it is minimally acceptable.

When the server offers choices of authentication schemes using the WWW-
Authenticate header, the strength of the resulting authentication is
only as good as that of the of the weakest of the authentication
schemes. See section 4.8 below for discussion of particular attack
scenarios that exploit multiple authentication schemes.




Franks, et al.                                     [Page 22]

INTERNET-DRAFT      HTTP Authentication            09/02/98

4.7 Online dictionary attacks

If the attacker can eavesdrop, then it can test any overheard
nonce/response pairs against a list of common words. Such a list is
usually much smaller than the total number of possible passwords. The
cost of computing the response for each password on the list is paid
once for each challenge.

The server can mitigate this attack by not allowing users to select
passwords that are in a dictionary.

4.8 Man in the Middle

Both Basic and Digest authentication are vulnerable to "man in the
middle" (MITM) attacks, for example, from a hostile or compromised
proxy. Clearly, this would present all the problems of eavesdropping.
But it also offers some additional opportunities to the attacker.

A possible man-in-the-middle attack would be to add a weak
authentication scheme to the set of choices, hoping that the client will
use one that exposes the user's credentials (e.g. password). For this
reason, the client should always use the strongest scheme that it
understands from the choices offered.

An even better MITM attack would be to remove all offered choices,
replacing them with a challenge that requests only Basic authentication,
then uses the cleartext credentials from the Basic authentication to
authenticate to the origin server using the stronger scheme it
requested. A particularly insidious way to mount such a MITM attack
would be to offer a "free" proxy caching service to gullible users.

User agents should consider measures such as presenting a visual
indication at the time of the credentials request of what authentication
scheme is to be used, or remembering the strongest authentication scheme
ever requested by a server and produce a warning message before using a
weaker one. It might also be a good idea for the user agent to be
configured to demand Digest authentication in general, or from specific
sites.

Or, a hostile proxy might spoof the client into making a request the
attacker wanted rather than one the client wanted. Of course, this is
still much harder than a comparable attack against Basic Authentication.

4.9 Chosen plaintext attacks

With Digest authentication, a MITM or a malicious server can arbitrarily
choose the nonce that the client will use to compute the response. This
is called a "chosen plaintext" attack. The ability to choose the nonce
is known to make cryptanalysis much easier [8].

However, no way to analyze the MD5 one-way function used by Digest using
chosen plaintext is currently known.

The countermeasure against this attack is for clients to be configured
to require the use of the optional "cnonce" directive; this allows the


Franks, et al.                                     [Page 23]

INTERNET-DRAFT      HTTP Authentication            09/02/98

client to vary the input to the hash in a way not chosen by the
attacker.

4.10 Precomputed dictionary attacks

With Digest authentication, if the attacker can execute a chosen
plaintext attack, the attacker can precompute the response for many
common words to a nonce of its choice, and store a dictionary of
(response, password) pairs. Such precomputation can often be done in
parallel on many machines. It can then use the chosen plaintext attack
to acquire a response corresponding to that challenge, and just look up
the password in the dictionary. Even if most passwords are not in the
dictionary, some might be. Since the attacker gets to pick the
challenge, the cost of computing the response for each password on the
list can be amortized over finding many passwords. A dictionary with 100
million password/response pairs would take about 3.2 gigabytes of disk
storage.

The countermeasure against this attack is to for clients to be
configured to require the use of the optional "cnonce" directive.

4.11 Batch brute force attacks

With Digest authentication, a MITM can execute a chosen plaintext
attack, and can gather responses from many users to the same nonce. It
can then find all the passwords within any subset of password space that
would generate one of the nonce/response pairs in a single pass over
that space. It also reduces the time to find the first password by a
factor equal to the number of nonce/response pairs gathered. This search
of the password space can often be done in parallel on many machines,
and even a single machine can search large subsets of the password space
very quickly -- reports exist of searching all passwords with six or
fewer letters in a few hours.

The countermeasure against this attack is to for clients to be
configured to require the use of the optional "cnonce" directive.

4.12 Spoofing by Counterfeit Servers

Basic Authentication is vulnerable to spoofing by counterfeit servers.
If a user can be led to believe that she is connecting to a host
containing information protected by a password she knows, when in fact
she is connecting to a hostile server, then the hostile server can
request a password, store it away for later use, and feign an error.
This type of attack is more difficult with Digest Authentication -- but
the client must know to demand that Digest authentication be used,
perhaps using some of the techniques described above to counter "man-in-
the-middle" attacks.  Again, the user can be helped in detecting this
attack by a visual indication of the authentication mechanism in use
with appropriate guidance in interpreting the implications of each
scheme.

4.13 Storing passwords

Digest authentication requires that the authenticating agent (usually
the server) store some data derived from the user's name and password in

Franks, et al.                                     [Page 24]

INTERNET-DRAFT      HTTP Authentication            09/02/98

a "password file" associated with a given realm. Normally this might
contain pairs consisting of username and H(A1), where H(A1) is the
digested value of the username, realm, and password as described above.

The security implications of this are that if this password file is
compromised, then an attacker gains immediate access to documents on the
server using this realm. Unlike, say a standard UNIX password file, this
information need not be decrypted in order to access documents in the
server realm associated with this file. On the other hand, decryption,
or more likely a brute force attack, would be necessary to obtain the
user's password. This is the reason that the realm is part of the
digested data stored in the password file. It means that if one Digest
authentication password file is compromised, it does not automatically
compromise others with the same username and password (though it does
expose them to brute force attack).

There are two important security consequences of this. First the
password file must be protected as if it contained unencrypted
passwords, because for the purpose of accessing documents in its realm,
it effectively does.

A second consequence of this is that the realm string should be unique
among all realms which any single user is likely to use. In particular a
realm string should include the name of the host doing the
authentication. The inability of the client to authenticate the server
is a weakness of Digest Authentication.

4.14 Summary

By modern cryptographic standards Digest Authentication is weak. But for
a large range of purposes it is valuable as a replacement for Basic
Authentication. It remedies some, but not all, weaknesses of Basic
Authentication. Its strength may vary depending on the implementation.
In particular the structure of the nonce (which is dependent on the
server implementation) may affect the ease of mounting a replay attack.
A range of server options is appropriate since, for example, some
implementations may be willing to accept the server overhead of one-time
nonces or digests to eliminate the possibility of replay. Others may
satisfied with a nonce like the one recommended above restricted to a
single IP address and a single ETag or with a limited lifetime.

The bottom line is that *any* compliant implementation will be
relatively weak by cryptographic standards, but *any* compliant
implementation will be far superior to Basic Authentication.

5 Sample implementation

The following code implements the calculations of H(A1), H(A2), request-
digest and response-digest, and a test program which computes the values
used in the example of section 3.5. It uses the MD5 implementation from
RFC 1321.

File "digcalc.h":


#define HASHLEN 16

Franks, et al.                                     [Page 25]

INTERNET-DRAFT      HTTP Authentication            09/02/98

typedef char HASH[HASHLEN];
#define HASHHEXLEN 32
typedef char HASHHEX[HASHHEXLEN+1];
#define IN
#define OUT

/* calculate H(A1) as per HTTP Digest spec */
void DigestCalcHA1(
    IN char * pszAlg,
    IN char * pszUserName,
    IN char * pszRealm,
    IN char * pszPassword,
    IN char * pszNonce,
    IN char * pszCNonce,
    OUT HASHHEX SessionKey
    );

/* calculate request-digest/response-digest as per HTTP Digest spec */
void DigestCalcResponse(
    IN HASHHEX HA1,           /* H(A1) */
    IN char * pszNonce,       /* nonce from server */
    IN char * pszNonceCount,  /* 8 hex digits */
    IN char * pszCNonce,      /* client nonce */
    IN char * pszQop,         /* qop-value: "", "auth", "auth-int" */
    IN char * pszMethod,      /* method from the request */
    IN char * pszDigestUri,   /* requested URL */
    IN HASHHEX HEntity,       /* H(entity body) if qop="auth-int" */
    OUT HASHHEX Response      /* request-digest or response-digest */
    );

File "digcalc.c":

#include <global.h>
#include <md5.h>
#include <string.h>
#include "digcalc.h"

void CvtHex(
    IN HASH Bin,
    OUT HASHHEX Hex
    )
{
    unsigned short i;
    unsigned char j;

    for (i = 0; i < HASHLEN; i++) {
        j = (Bin[i] >> 4) & 0xf;
        if (j <= 9)
            Hex[i*2] = (j + '0');
         else
            Hex[i*2] = (j + 'a' - 10);
        j = Bin[i] & 0xf;
        if (j <= 9)
            Hex[i*2+1] = (j + '0');
         else
            Hex[i*2+1] = (j + 'a' - 10);

Franks, et al.                                     [Page 26]

INTERNET-DRAFT      HTTP Authentication            09/02/98

    };
    Hex[HASHHEXLEN] = '\0';
};

/* calculate H(A1) as per spec */
void DigestCalcHA1(
    IN char * pszAlg,
    IN char * pszUserName,
    IN char * pszRealm,
    IN char * pszPassword,
    IN char * pszNonce,
    IN char * pszCNonce,
    OUT HASHHEX SessionKey
    )
{
      MD5_CTX Md5Ctx;
      HASH HA1;

      MD5Init(&Md5Ctx);
      MD5Update(&Md5Ctx, pszUserName, strlen(pszUserName));
      MD5Update(&Md5Ctx, ":", 1);
      MD5Update(&Md5Ctx, pszRealm, strlen(pszRealm));
      MD5Update(&Md5Ctx, ":", 1);
      MD5Update(&Md5Ctx, pszPassword, strlen(pszPassword));
      MD5Final(HA1, &Md5Ctx);
      if (stricmp(pszAlg, "md5-sess") == 0) {
            MD5Init(&Md5Ctx);
            MD5Update(&Md5Ctx, HA1, HASHLEN);
            MD5Update(&Md5Ctx, ":", 1);
            MD5Update(&Md5Ctx, pszNonce, strlen(pszNonce));
            MD5Update(&Md5Ctx, ":", 1);
            MD5Update(&Md5Ctx, pszCNonce, strlen(pszCNonce));
            MD5Final(HA1, &Md5Ctx);
      };
      CvtHex(HA1, SessionKey);
};

/* calculate request-digest/response-digest as per HTTP Digest spec */
void DigestCalcResponse(
    IN HASHHEX HA1,           /* H(A1) */
    IN char * pszNonce,       /* nonce from server */
    IN char * pszNonceCount,  /* 8 hex digits */
    IN char * pszCNonce,      /* client nonce */
    IN char * pszQop,         /* qop-value: "", "auth", "auth-int" */
    IN char * pszMethod,      /* method from the request */
    IN char * pszDigestUri,   /* requested URL */
    IN HASHHEX HEntity,       /* H(entity body) if qop="auth-int" */
    OUT HASHHEX Response      /* request-digest or response-digest */
    )
{
      MD5_CTX Md5Ctx;
      HASH HA2;
      HASH RespHash;
       HASHHEX HA2Hex;

      // calculate H(A2)

Franks, et al.                                     [Page 27]

INTERNET-DRAFT      HTTP Authentication            09/02/98

      MD5Init(&Md5Ctx);
      MD5Update(&Md5Ctx, pszMethod, strlen(pszMethod));
      MD5Update(&Md5Ctx, ":", 1);
      MD5Update(&Md5Ctx, pszDigestUri, strlen(pszDigestUri));
      if (stricmp(pszQop, "auth-int") == 0) {
            MD5Update(&Md5Ctx, ":", 1);
            MD5Update(&Md5Ctx, HEntity, HASHHEXLEN);
      };
      MD5Final(HA2, &Md5Ctx);
       CvtHex(HA2, HA2Hex);

      // calculate response
      MD5Init(&Md5Ctx);
      MD5Update(&Md5Ctx, HA1, HASHHEXLEN);
      MD5Update(&Md5Ctx, ":", 1);
      MD5Update(&Md5Ctx, pszNonce, strlen(pszNonce));
      MD5Update(&Md5Ctx, ":", 1);
      if (*pszQop) {
          MD5Update(&Md5Ctx, pszNonceCount, strlen(pszNonceCount));
          MD5Update(&Md5Ctx, ":", 1);
          MD5Update(&Md5Ctx, pszCNonce, strlen(pszCNonce));
          MD5Update(&Md5Ctx, ":", 1);
          MD5Update(&Md5Ctx, pszQop, strlen(pszQop));
          MD5Update(&Md5Ctx, ":", 1);
      };
      MD5Update(&Md5Ctx, HA2Hex, HASHHEXLEN);
      MD5Final(RespHash, &Md5Ctx);
      CvtHex(RespHash, Response);
};

File "digtest.c":


#include <stdio.h>
#include "digcalc.h"

void main(int argc, char ** argv) {

      char * pszNonce = "dcd98b7102dd2f0e8b11d0f600bfb0c093";
      char * pszCNonce = "0a4f113b";
      char * pszUser = "Mufasa";
      char * pszRealm = "testrealm@host.com";
      char * pszPass = "Circle Of Life";
      char * pszAlg = "md5";
      char szNonceCount[9] = "00000001";
      char * pszMethod = "GET";
      char * pszQop = "auth";
      char * pszURI = "/dir/index.html";
      HASHHEX HA1;
      HASHHEX HA2 = "";
      HASHHEX Response;

      DigestCalcHA1(pszAlg, pszUser, pszRealm, pszPass, pszNonce,
pszCNonce, HA1);
      DigestCalcResponse(HA1, pszNonce, szNonceCount, pszCNonce, pszQop,
       pszMethod, pszURI, HA2, Response);

Franks, et al.                                     [Page 28]

INTERNET-DRAFT      HTTP Authentication            09/02/98

      printf("Response = %s\n", Response);
};
6 Acknowledgments

Eric W. Sink, of AbiSource, Inc., was one of the original authors before
the specification underwent substantial revision.

In addition to the authors, valuable discussion instrumental in creating
this document has come from Peter J. Churchyard, Ned Freed, and David M.
Kristol.

Jim Gettys and Larry Masinter edited this document for update.

7 References


[1]  Berners-Lee, T.,  Fielding, R., and H. Frystyk, "Hypertext Transfer
  Protocol -- HTTP/1.0", RFC 1945, May 1996.


[2]  Fielding, R.,  Gettys, J., Mogul, J. C., Frysyk, H., Masinter, L.,
  Leach, P., Berners-Lee, T., " Hypertext Transfer Protocol --
  HTTP/1.1",  Work In Progress of the HTTP working group, July, 1998.


[3]  Rivest, R., "The MD5 Message-Digest Algorithm", RFC 1321, April
  1992.


[4]  Freed, N., and N. Borenstein. "Multipurpose Internet Mail
  Extensions (MIME) Part One: Format of Internet Message Bodies." RFC
  2045, Innosoft, First Virtual, November 1996.


[5]  Dierks, T. and C. Allen "The TLS Protocol, Version 1.0," Work In
  Progress of the TLS working group, November, 1997.


[6]  Franks, J., Hallam-Baker, P., Hostetler, J., Leach, P., Luotonen,
  A., Sink, E., Stewart, L.,"An Extension to HTTP : Digest Access
  Authentication." RFC 2069,  January, 1997.


[7]  Berners Lee, T, Fielding, R., Masinter, L., "Uniform Resource
  Identifiers (URI): Generic Syntax and Semantics," Work in Progress,
  November, 1997.

[8]  Kaliski, B.,Robshaw, M., "Message Authentication with MD5",
CryptoBytes, Sping 1995, RSA Inc,
(http://www.rsa.com/rsalabs/pubs/cryptobytes/spring95/md5.htm)

[9]  Klensin, J.,Catoe, R., Krumviede, P., "IMAP/POP AUTHorize Extension
for Simple Challenge/Response", September 1997.

[10] Morgan, B., Alvestrand, H., Hodges, J., Wahl, M., "Authentication
Methods for LDAP", 07/07/1998. Work in progress, <draft-ietf-ldapext-
authmeth-02.txt>




Franks, et al.                                     [Page 29]

INTERNET-DRAFT      HTTP Authentication            09/02/98

8 Authors' Addresses

John Franks
Professor of Mathematics
Department of Mathematics
Northwestern University
Evanston, IL 60208-2730, USA

EMail: john@math.nwu.edu

Phillip M. Hallam-Baker
Principal Consultant
Verisign Inc.
301 Edgewater Place
Suite 210
Wakefield MA 01880, USA

EMail: pbaker@verisign.com

Jeffery L. Hostetler
Software Craftsman
AbiSource, Inc.
6 Dunlap Court
Savoy, IL 61874

EMail: jeff@AbiSource.com

Scott D. Lawrence
Agranat Systems, Inc.
1345 Main St.
Waltham, MA  02154, USA

EMail: lawrence@agranat.com

Paul J. Leach
Microsoft Corporation
1 Microsoft Way
Redmond, WA 98052, USA

EMail: paulle@microsoft.com

Ari Luotonen
Member of Technical Staff
Netscape Communications Corporation
501 East Middlefield Road
Mountain View, CA 94043, USA

EMail: luotonen@netscape.com

Lawrence C. Stewart
Open Market, Inc.
215 First Street
Cambridge, MA  02142, USA

EMail: stewart@OpenMarket.com


Franks, et al.                                     [Page 30]

INTERNET-DRAFT      HTTP Authentication            09/02/98

9 Full Copyright Statement

Copyright (C) The Internet Society (1998). All Rights Reserved.

This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it or
assist in its implmentation may be prepared, copied, published and
distributed, in whole or in part, without restriction of any kind,
provided that the above copyright notice and this paragraph are included
on all such copies and derivative works. However, this document itself
may not be modified in any way, such as by removing the copyright notice
or references to the Internet Society or other Internet organizations,
except as needed for the purpose of developing Internet standards in
which case the procedures for copyrights defined in the Internet
Standards process must be followed, or as required to translate it into
languages other than English.

The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.

This document and the information contained herein is provided on an "AS
IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK
FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT
INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.































Franks, et al.                                     [Page 31]


Html markup produced by rfcmarkup 1.107, available from http://tools.ietf.org/tools/rfcmarkup/