[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 04 05 06 07 08 09 RFC 4193

INTERNET-DRAFT                                          R. Hinden, Nokia
September 24, 2004                                   B. Haberman, JHU-APL





                  Unique Local IPv6 Unicast Addresses

               <draft-ietf-ipv6-unique-local-addr-06.txt>




Status of this Memo

   By submitting this Internet-Draft, we certify that any applicable
   patent or other IPR claims of which I am aware have been disclosed,
   and any of which I become aware will be disclosed, in accordance with
   RFC 3668.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than a "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/1id-abstracts.html

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html

   This internet draft expires on March 29, 2005.


Abstract

   This document defines an IPv6 unicast address format that is globally
   unique and is intended for local communications, usually inside of a
   site.  They are not expected to be routable on the global Internet.






draft-ietf-ipv6-unique-local-addr-06.txt                        [Page 1]

INTERNET-DRAFT     Unique Local IPv6 Unicast Addresses    September 2004


Table of Contents

   1.0 Introduction....................................................2
   2.0 Acknowledgments.................................................3
   3.0 Local IPv6 Unicast Addresses....................................3
   3.1 Format..........................................................3
   3.1.1 Background....................................................4
   3.2 Global ID.......................................................4
   3.2.1 Locally Assigned Global IDs...................................5
   3.2.2 Sample Code for Pseudo-Random Global ID Algorithm.............6
   3.2.3 Analysis of the Uniqueness of Global IDs......................6
   3.3 Scope Definition................................................7
   4.0 Routing.........................................................7
   5.0 Renumbering and Site Merging....................................8
   6.0 Site Border Router and Firewall Packet Filtering................8
   7.0 DNS Issues......................................................9
   8.0 Application and Higher Level Protocol Issues....................9
   9.0 Use of Local IPv6 Addresses for Local Communications............9
   10.0 Use of Local IPv6 Addresses with VPNs.........................10
   11.0 Advantages and Disadvantages..................................10
   12.0 Security Considerations.......................................11
   13.0 IANA Considerations...........................................11
   14.0 References....................................................12
   14.1 Normative References..........................................12
   14.2 Informative References........................................13
   15.0 Authors' Addresses............................................13
   16.0 Change Log....................................................14


1.0 Introduction

   This document defines an IPv6 unicast address format that is globally
   unique and is intended for local communications [IPV6].  These
   addresses are called Unique Local IPv6 Unicast Addresses and are
   abbreviated in this document as Local IPv6 addresses.  They are not
   expected to be routable on the global Internet.  They are routable
   inside of a more limited area such as a site.  They may also be
   routed between a limited set of sites.

   Local IPv6 unicast addresses have the following characteristics:

      - Globally unique prefix.
      - Well known prefix to allow for easy filtering at site
        boundaries.
      - Allows sites to be combined or privately interconnected without
        creating any address conflicts or requiring renumbering of
        interfaces using these prefixes.
      - Internet Service Provider independent and can be used for



draft-ietf-ipv6-unique-local-addr-06.txt                        [Page 2]

INTERNET-DRAFT     Unique Local IPv6 Unicast Addresses    September 2004


        communications inside of a site without having any permanent or
        intermittent Internet connectivity.
      - If accidentally leaked outside of a site via routing or DNS,
        there is no conflict with any other addresses.
      - In practice, applications may treat these addresses like global
        scoped addresses.

   This document defines the format of Local IPv6 addresses, how to
   allocate them, and usage considerations including routing, site
   border routers, DNS, application support, VPN usage, and guidelines
   for how to use for local communication inside a site.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC 2119].


2.0 Acknowledgments

   The underlying idea of creating Local IPv6 addresses described in
   this document been proposed a number of times by a variety of people.
   The authors of this draft do not claim exclusive credit.  Credit goes
   to Brian Carpenter, Christian Huitema, Aidan Williams, Andrew White,
   Charlie Perkins, and many others.  The authors would also like to
   thank Brian Carpenter, Charlie Perkins, Harald Alvestrand, Keith
   Moore, Margaret Wasserman, Shannon Behrens, Alan Beard, Hans Kruse,
   Geoff Huston, Pekka Savola, Christian Huitema, and Tim Chown for
   their comments and suggestions on this document.


3.0 Local IPv6 Unicast Addresses

3.1 Format

   The Local IPv6 addresses are created using a pseudo-randomly
   allocated global ID.  They have the following format:

      | 7 bits |  41 bits   |  16 bits  |          64 bits            |
      +--------+------------+-----------+-----------------------------+
      | prefix | global ID  | subnet ID |        interface ID         |
      +--------+------------+-----------+-----------------------------+

   Where:

      prefix            FC00::/7 prefix to identify Local IPv6 unicast
                        addresses.

      global ID         41-bit global identifier used to create a



draft-ietf-ipv6-unique-local-addr-06.txt                        [Page 3]

INTERNET-DRAFT     Unique Local IPv6 Unicast Addresses    September 2004


                        globally unique prefix. See section 3.2 for
                        additional information.

      subnet ID         16-bit subnet ID is an identifier of a subnet
                        within the site.

      interface ID      64-bit interface ID as defined in [ADDARCH].


3.1.1 Background

   There were a range of choices available when choosing the size of the
   prefix and global ID field length.  There is a direct tradeoff
   between having a global ID field large enough to support foreseeable
   future growth and not using too much of the IPv6 address space
   needlessly.  A reasonable way of evaluating a specific field length
   is to compare it to a projected 2050 world population of 9.3 billion
   [POPUL] and the number of resulting /48 prefixes per person.  A range
   of prefix choices is shown in the following table:

    Prefix  Global ID     Number of          Prefixes    % of IPv6
            Length        /48 Prefixes       per Person  Address Space

    /11       37           137,438,953,472     15         0.049%
    /10       38           274,877,906,944     30         0.098%
    /9        39           549,755,813,888     59         0.195%
    /8        40         1,099,511,627,776    118         0.391%
    /7        41         2,199,023,255,552    236         0.781%
    /6        42         4,398,046,511,104    473         1.563%

   A very high utilization ratio of these allocations can be assumed
   because the global ID field does not require internal structure, and
   there is no reason to be able to aggregate the prefixes.

   The authors believe that a /7 prefix resulting in a 41 bit global ID
   is a good choice.  It provides for a large number of assignments
   (i.e., 2.2 trillion) and at the same time uses less than .8% of the
   total IPv6 address space.  It is unlikely that this space will be
   exhausted.  If more than this were to be needed, then additional IPv6
   address space could be allocated for this purpose.


3.2 Global ID

   The allocation of global IDs should be pseudo-random [RANDOM].  They
   should not be assigned sequentially or with well known numbers.  This
   is to ensure that there is not any relationship between allocations
   and to help clarify that these prefixes are not intended to be routed



draft-ietf-ipv6-unique-local-addr-06.txt                        [Page 4]

INTERNET-DRAFT     Unique Local IPv6 Unicast Addresses    September 2004


   globally.  Specifically, these prefixes are designed to not
   aggregate.

   There are two ways to allocate Global IDs.  These are centrally by a
   allocation authority and locally by the site.  The Global ID is split
   into two parts for each type of allocation.  The prefixes for each
   type are:

      FC00::/8    Centrally assigned
      FD00::/8    Locally assigned

   Each results in a 40-bit space to allocate.

   Two assignment methods are included because they have different
   properties.  The centrally assigned global IDs are uniquely assigned.
   The local assignments are self generated and do not need any central
   coordination or assignment, but have a lower (but still adequate)
   probability of being unique.  It is expected that large managed sites
   will prefer central assignments and small or disconnected sites will
   prefer local assignments.  It is recommended that sites planning to
   use Local IPv6 addresses for extensive inter-site communication,
   initially or as a future possibility, use a centrally assigned prefix
   as there is no possibility of assignment conflicts.  Sites are free
   to choose either approach.

   This document only allocates the prefix (FC00::/8) for centrally
   assigned local IPv6 addresses.  The characteristics and technical
   allocation requirements for centrally assigned Local IPv6 addresses
   will be defined in a separate document.


3.2.1 Locally Assigned Global IDs

   Global IDs can be generated locally by an individual site.  This
   makes it easy to get a prefix without the need to contact an
   assignment authority or internet service provider.  There is not as
   high a degree of assurance that the prefix will not conflict with
   another locally generated prefix, but the likelihood of conflict is
   small.  Sites that are not comfortable with this degree of
   uncertainty should use a centrally assigned global ID.

   Locally assigned global IDs MUST be generated with a pseudo-random
   algorithm consistent with [RANDOM].  Section 3.2.2 describes a
   suggested algorithm.  It is important to ensure a reasonable
   likelihood uniqueness that all sites generating a Global IDs use a
   functionally similar algorithm.

   The use of a pseudo-random algorithm to generate global IDs in the



draft-ietf-ipv6-unique-local-addr-06.txt                        [Page 5]

INTERNET-DRAFT     Unique Local IPv6 Unicast Addresses    September 2004


   locally assigned prefix gives an assurance that any network numbered
   using such a prefix is highly unlikely to have that address space
   clash with any other network that has another locally assigned prefix
   allocated to it.   This is a particularly useful property when
   considering a number of scenarios including networks that merge,
   overlapping VPN address space, or hosts mobile between such networks.


3.2.2  Sample Code for Pseudo-Random Global ID Algorithm

   The algorithm described below is intended to be used for locally
   assigned Global IDs.  In each case the resulting global ID will be
   used in the appropriate prefix as defined in section 3.2.

     1) Obtain the current time of day in 64-bit NTP format [NTP].
     2) Obtain an EUI-64 identifier from the system running this
        algorithm.  If an EUI-64 does not exist, one can be created from
        a 48-bit MAC address as specified in [ADDARCH].  If an EUI-64
        cannot be obtained or created, a suitably unique identifier,
        local to the node, should be used (e.g. system serial number).
     3) Concatenate the time of day with the system-specific identifier
        creating a key.
     4) Compute an MD5 digest on the key as specified in [MD5DIG].
     5) Use the least significant 40 bits as the Global ID.

   This algorithm will result in a global ID that is reasonably unique
   and can be used as a Global ID.


3.2.3  Analysis of the Uniqueness of Global IDs

   The selection of a pseudo random global ID is similar to the
   selection of an SSRC identifier in RTP/RTCP defined in section 8.1 of
   [RTP].  This analysis is adapted from that document.

   Since the global ID is chosen randomly, it is possible that two or
   more networks that have an inter-network connection using globally-
   unique local addresses will chose the same global ID.  The
   probability of collision can be approximated based on the number of
   connections between networks using globally-unique local addresses
   and the length of the ID (40 bits).  The formula

      P = 1 - exp(-N**2 / 2**(L+1))

   approximates the probability of collision (where N is the number
   connections and L is the length of the global ID).

   The following table shows the probability of a collision for a range



draft-ietf-ipv6-unique-local-addr-06.txt                        [Page 6]

INTERNET-DRAFT     Unique Local IPv6 Unicast Addresses    September 2004


   of connections using a 40 bit global ID field.

      Connections      Probability of Collision

          2                1.81*10^-12
         10                4.54*10^-11
        100                4.54*10^-09
       1000                4.54*10^-07
      10000                4.54*10^-05

   Based on this analysis the uniqueness of locally generated global IDs
   is adequate for sites planning a small to moderate amount of inter-
   site communication using locally generated global IDs.  Sites
   planning more extensive inter-site communication should consider
   using the centrally assigned global ID.


3.3 Scope Definition

   By default, the scope of these addresses is global.  That is, they
   are not limited by ambiguity like the site-local addresses defined in
   [ADDARCH].  Rather, these prefixes are globally unique, and as such,
   their applicability is greater than site-local addresses.  Their
   limitation is in the routability of the prefixes, which is limited to
   a site and any explicit routing agreements with other sites to
   propagate them.  Also, unlike site-locals, a site may have more than
   one of these prefixes and use them at the same time.


4.0 Routing

   Local IPv6 addresses are designed to be routed inside of a site in
   the same manner as other types of unicast addresses.  They can be
   carried in any IPv6 routing protocol without any change.

   It is expected that they would share the same subnet IDs with
   provider based global unicast addresses if they were being used
   concurrently [GLOBAL].

   Any router that is used between sites must be configured to filter
   out any incoming or outgoing Local IPv6 unicast routes.  The
   exception to this is if specific /48 or longer IPv6 local unicast
   routes have been configured to allow for inter-site communication.

   If BGP is being used at the site border with an ISP, the default BGP
   configuration must be set to to keep any Local IPv6 address prefixes
   from being advertised outside of the site or for these prefixes to be
   learned from another site.  The exception to this is if there are



draft-ietf-ipv6-unique-local-addr-06.txt                        [Page 7]

INTERNET-DRAFT     Unique Local IPv6 Unicast Addresses    September 2004


   specific /48 or longer routes created for one or more Local IPv6
   prefixes.


5.0 Renumbering and Site Merging

   The use of Local IPv6 addresses in a site results in making
   communication using these addresses independent of renumbering a
   site's provider based global addresses.

   When merging multiple sites the addresses created with these prefixes
   are unlikely to need to be renumbered because all of the addresses
   have a high probability of being unique.  Routes for each specific
   prefix would have to be configured to allow routing to work correctly
   between the formerly separate sites.


6.0 Site Border Router and Firewall Packet Filtering

   While no serious harm will be done if packets with these addresses
   are sent outside of a site via a default route, it is recommended
   that routers be configured by default to keep any packets with Local
   IPv6 destination addresses from leaking outside of the site and to
   keep any site prefixes from being advertised outside of their site.

   Site border routers should install a "reject" route for the Local
   IPv6 prefix FC00::/7.  This will ensure that packets with Local IPv6
   destination addresses will not be forwarded outside of the site via a
   default route.  Site border routers should respond with the
   appropriate ICMPv6 Destination Unreachable message to inform the
   source that the packet was not forwarded [ICMPV6].  This feedback is
   important to avoid transport protocol timeouts.

   Site border routers and firewalls should not forward any packets with
   Local IPv6 source or destination addresses outside of the site unless
   they have been explicitly configured with routing information about
   specific /48 or longer Local IPv6 prefixes.  The default behavior of
   these devices should be to install a "reject" route for these
   prefixes.  Site border routers should respond with the appropriate
   ICMPv6 Destination Unreachable message to inform the source that the
   packet was not forwarded.

   Routers that maintain peering arrangements between Autonomous Systems
   throughout the Internet should obey the recommendations for site
   border routers unless configured otherwise.






draft-ietf-ipv6-unique-local-addr-06.txt                        [Page 8]

INTERNET-DRAFT     Unique Local IPv6 Unicast Addresses    September 2004


7.0 DNS Issues

   AAAA and PTR records for locally assigned local IPv6 addresses are
   not recommended to be installed in the global DNS.


8.0 Application and Higher Level Protocol Issues

   Application and other higher level protocols can treat Local IPv6
   addresses in the same manner as other types of global unicast
   addresses.  No special handling is required.  This type of addresses
   may not be reachable, but that is no different from other types of
   IPv6 global unicast addresses.  Applications need to be able to
   handle multiple addresses that may or may not be reachable any point
   in time.  In most cases this complexity should be hidden in APIs.

   From a host's perspective this difference shows up as different
   reachability than global unicast and could be handled by default that
   way.  In some cases it is better for nodes and applications to treat
   them differently from global unicast addresses.  A starting point
   might be to give them preference over global unicast, but fall back
   to global unicast if a particular destination is found to be
   unreachable.  Much of this behavior can be controlled by how they are
   allocated to nodes and put into the DNS.  However it is useful if a
   host can have both types of addresses and use them appropriately.

   Note that the address selection mechanisms of [ADDSEL], and in
   particular the policy override mechanism replacing default address
   selection, are expected to be used on a site where Local IPv6
   addresses are configured.


9.0 Use of Local IPv6 Addresses for Local Communications

   Local IPv6 addresses, like global scope unicast addresses, are only
   assigned to nodes if their use has been enabled (via IPv6 address
   autoconfiguration [ADDAUTO], DHCPv6 [DHCP6], or manually).  They are
   not created automatically the way that IPv6 link-local addresses are
   and will not appear or be used unless they are purposely configured.

   In order for hosts to autoconfigure Local IPv6 addresses, routers
   have to be configured to advertise Local IPv6 /64 prefixes in router
   advertisements, or a DHCPv6 server must have been configured to
   assign them.  In order for a node to learn the Local IPv6 address of
   another node, the Local IPv6 address must have been installed in the
   DNS or another naming system.  For these reasons, it is straight
   forward to control their usage in a site.




draft-ietf-ipv6-unique-local-addr-06.txt                        [Page 9]

INTERNET-DRAFT     Unique Local IPv6 Unicast Addresses    September 2004


   To limit the use of Local IPv6 addresses the following guidelines
   apply:

      - Nodes that are to only be reachable inside of a site:  The local
        DNS should be configured to only include the Local IPv6
        addresses of these nodes.  Nodes with only Local IPv6 addresses
        must not be installed in the global DNS.

      - Nodes that are to be limited to only communicate with other
        nodes in the site:  These nodes should be set to only
        autoconfigure Local IPv6 addresses via [ADDAUTO] or to only
        receive Local IPv6 addresses via [DHCP6].  Note: For the case
        where both global and Local IPv6 prefixes are being advertised
        on a subnet, this will require a switch in the devices to only
        autoconfigure Local IPv6 addresses.

      - Nodes that are to be reachable from inside of the site and from
        outside of the site:  The DNS should be configured to include
        the global addresses of these nodes.  The local DNS may be
        configured to also include the Local IPv6 addresses of these
        nodes.

      - Nodes that can communicate with other nodes inside of the site
        and outside of the site: These nodes should autoconfigure global
        addresses via [ADDAUTO] or receive global address via [DHCP6].
        They may also obtain Local IPv6 addresses via the same
        mechanisms.


10.0 Use of Local IPv6 Addresses with VPNs

   Local IPv6 addresses can be used for inter-site Virtual Private
   Networks (VPN) if appropriate routes are set up.  Because the
   addresses are unique these VPNs will work reliably and without the
   need for translation.  They have the additional property that they
   will continue to work if the individual sites are renumbered or
   merged.


11.0 Advantages and Disadvantages

11.1 Advantages

   This approach has the following advantages:

      - Provides Local IPv6 prefixes that can be used independently of
        any provider based IPv6 unicast address allocations.  This is
        useful for sites not always connected to the Internet or sites



draft-ietf-ipv6-unique-local-addr-06.txt                       [Page 10]

INTERNET-DRAFT     Unique Local IPv6 Unicast Addresses    September 2004


        that wish to have a distinct prefix that can be used to localize
        traffic inside of the site.
      - Applications can treat these addresses in an identical manner as
        any other type of global IPv6 unicast addresses.
      - Sites can be merged without any renumbering of the Local IPv6
        addresses.
      - Sites can change their provider based IPv6 unicast address
        without disrupting any communication using Local IPv6 addresses.
      - Well known prefix that allows for easy filtering at site
        boundary.
      - Can be used for inter-site VPNs.
      - If accidently leaked outside of a site via routing or DNS, there
        is no conflict with any other addresses.

11.2 Disadvantages

   This approach has the following disadvantages:

      - Not possible to route Local IPv6 prefixes on the global Internet
        with current routing technology.  Consequentially, it is
        necessary to have the default behavior of site border routers to
        filter these addresses.
      - There is a very low probability of non-unique locally assigned
        global IDs being generated by the algorithm in section 3.2.3.
        This risk can be ignored for all practical purposes, but it
        leads to a theoretical risk of clashing address prefixes.


12.0 Security Considerations

   Local IPv6 addresses do not provide any inherent security to the
   nodes that use them.  They may be used with filters at site
   boundaries to keep Local IPv6 traffic inside of the site, but this is
   no more or less secure than filtering any other type of global IPv6
   unicast addresses.

   Local IPv6 addresses do allow for address-based security mechanisms,
   including IPSEC, across end to end VPN connections.


13.0 IANA Considerations

   The IANA is instructed to assign the FC00::/7 prefix for Unique Local
   IPv6 unicast addresses.

   The prefix is divided in half for the following purposes:

      FC00::/8    Centrally assigned



draft-ietf-ipv6-unique-local-addr-06.txt                       [Page 11]

INTERNET-DRAFT     Unique Local IPv6 Unicast Addresses    September 2004


      FD00::/8    Locally assigned

   The IANA is instructed to reserve the prefix FC00::/8 for Centrally
   assigned Unique Local IPv6 unicast addresses.

   The FD00::/8 prefix is defined in this specification for Locally
   assigned Unique Local IPv6 unicast addresses.


14.0 References

14.1 Normative References

   [ADDARCH] Hinden, R., S. Deering, S., "IP Version 6 Addressing
             Architecture", RFC 3513, April 2003.

   [GLOBAL]  Hinden, R., S. Deering, E. Nordmark, "IPv6 Global Unicast
             Address Format", RFC 3587, August 2003.

   [ICMPV6]  Conta, A., S. Deering, "Internet Control Message Protocol
             (ICMPv6) for the Internet Protocol Version 6 (IPv6)
             Specification", RFC2463, December 1998.

   [IPV6]    Deering, S., R. Hinden, "Internet Protocol, Version 6
             (IPv6) Specification", RFC 2460, December 1998.

   [MD5DIG]  Rivest, R., "The MD5 Message-Digest Algorithm", RFC 1321,
             April 1992.

   [NTP]     Mills, David L., "Network Time Protocol (Version 3)
             Specification, Implementation and Analysis", RFC 1305,
             March 1992.

   [POPUL]   Population Reference Bureau, "World Population Data Sheet
             of the Population Reference Bureau 2002",  August 2002.

   [RANDOM]  Eastlake, D. 3rd, S. Crocker, J. Schiller, "Randomness
             Recommendations for Security", RFC 1750, December 1994.

   [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
             Requirement Levels", RFC 2119, BCP14, March 1997.










draft-ietf-ipv6-unique-local-addr-06.txt                       [Page 12]

INTERNET-DRAFT     Unique Local IPv6 Unicast Addresses    September 2004


14.2 Informative References

   [ADDAUTO] Thomson, S., T. Narten, "IPv6 Stateless Address
             Autoconfiguration", RFC 2462, December 1998.

   [ADDSEL]  Draves, R., "Default Address Selection for Internet
             Protocol version 6 (IPv6)", RFC 3484, February 2003.

   [DHCP6]   Droms, R., et. al., "Dynamic Host Configuration Protocol
             for IPv6 (DHCPv6)", RFC3315, July 2003.

   [RTP]     Schulzrinne, H., S. Casner, R. Frederick, V. Jacobson,
             "RTP: A Transport Protocol for Real-Time Applications"
             RFC3550, July 2003.


15.0 Authors' Addresses

   Robert M. Hinden
   Nokia
   313 Fairchild Drive
   Mountain View, CA 94043
   USA

   phone: +1 650 625-2004
   email: bob.hinden@nokia.com


   Brian Haberman
   Johns Hopkins University
   Applied Physics Lab
   11100 Johns Hopkins Road
   Laurel, MD 20723
   USA

   phone: +1 443 778 1319
   email: brian@innovationslab.net














draft-ietf-ipv6-unique-local-addr-06.txt                       [Page 13]

INTERNET-DRAFT     Unique Local IPv6 Unicast Addresses    September 2004


16.0 Change Log

   Draft <draft-ietf-ipv6-unique-local-addr-06.txt>
      o Clarify text to permit prefixes longer than /48 to be
        configured.
      o Changed text in section 7.0 to recommend that locally assigned
        ULA addresses are not installed in the global DNS and removed
        text about consequences of if they were installed in the global
        DNS.
      o Clarify the text in section 5.1 to state that there is a high
        probability that there will be no address conflict when
        renumbering.
      o Several minor editorial changes.

   Draft <draft-ietf-ipv6-unique-local-addr-05.txt>
      o Removed the definition and technical requirements for centrally
        assigned local address.  The Centrally assigned local addresses
        will be defined in a separate document.  This document defines
        the specific prefixes to be used for centrally and locally
        assigned IPv6 local addresses, but only the locally assigned
        local addresses are defined here.

   Draft <draft-ietf-ipv6-unique-local-addr-04.txt>

      o Clarified text in section 3.2.1 that central assigned prefixes
        should be assigned under the authority of a single allocation
        organization.
      o Added step to suggested pseudo-random algorithm that in the case
        of centrally assigned prefixes the computed global IDs should be
        verified against the escrow.
      o Added new text to section 3.2.2 that explains in more detail the
        need for pseudo-random global IDs (i.e., avoid duplicate
        allocations).
      o Rewrote section 7.0 to describe DNS AAAA and PTR records, and
        clarify when they might be installed in the global DNS.
      o Various editorial changes.

   Draft <draft-ietf-ipv6-unique-local-addr-03.txt>

      o Removed requirement of a fee per central allocation and updated
        IANA considerations to reflect this.  Rewrote text to focus on
        the requirement to avoid hoarding of allocations.
      o Changed "filtering" and "black hole routes" to "reject" routes.
      o Changed uppers case requirements (i.e., MUST, SHOULD, etc.) to
        lower case in sections giving operational advice.
      o Removed paragraph mentioning "Multicast DNS".
      o Various editorial changes.




draft-ietf-ipv6-unique-local-addr-06.txt                       [Page 14]

INTERNET-DRAFT     Unique Local IPv6 Unicast Addresses    September 2004


   Draft <draft-ietf-ipv6-unique-local-addr-02.txt>

      o Removed mention of 10 euro charge and changed text in section
        3.2.1 and IANA considerations to restate the requirement for low
        cost allocations and added specific requirement to prevent
        hording.
      o Added need to send ICMPv6 destination unreachable messages if
        packets are filtered or dropped at site boundaries.
      o Changed format section to list prefix sizes and definition, and
        changed discussion of prefix sizes to new background section.
      o Various editorial changes.

   Draft <draft-ietf-ipv6-unique-local-addr-01.txt>

      o Removed example of PIR as an example of an allocation authority
        and clarified the text that the IANA should delegate the
        centrally assigned prefix to an allocation authority.
      o Changed sample code for generating pseudo random Global IDs to
        not require any human input.  Changes from using birthday to
        unique token (e.g., EUI-64, serial number, etc.)  available on
        machine running the algorithm.
      o Added a new section analyzing the uniqueness properties of the
        pseudo random number algorithm.
      o Added text to recommend that centrally assigned local addresses
        be used for site planning extensive inter-site communication.
      o Clarified that domain border routers should follow site border
        router recommendations.
      o Clarified that AAAA DNS records should not be installed in the
        global DNS.
      o Several editorial changes.

   Draft <draft-ietf-ipv6-unique-local-addr-00.txt>

      o Changed file name to become an IPv6 w.g. group document.
      o Clarified language in Routing and Firewall sections.
      o Several editorial changes.

   Draft <draft-hinden-ipv6-global-local-addr-02.txt>

      o Changed title and name of addresses defined in this document to
        "Unique Local IPv6 Unicast Addresses" with abbreviation of
        "Local IPv6 addresses".
      o Several editorial changes.

   Draft <draft-hinden-ipv6-global-local-addr-01.txt>

      o Added section on scope definition and updated application
        requirement section.



draft-ietf-ipv6-unique-local-addr-06.txt                       [Page 15]

INTERNET-DRAFT     Unique Local IPv6 Unicast Addresses    September 2004


      o Clarified that, by default, the scope of these addresses is
        global.
      o Renumbered sections and general text improvements
      o Removed reserved global ID values
      o Added pseudo code for local allocation submitted by Brian
        Haberman and added him as an author.
      o Split Global ID values into centrally assigned and local
        assignments and added text to describe local assignments

   Draft <draft-hinden-ipv6-global-local-addr-00.txt>

      o Initial Draft







































draft-ietf-ipv6-unique-local-addr-06.txt                       [Page 16]


Html markup produced by rfcmarkup 1.109, available from https://tools.ietf.org/tools/rfcmarkup/