[Docs] [txt|pdf|xml|html] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: (draft-cole-manet-olsrv2-mib) 00 01 02 03 04 05 06 07 08 09 10 11 12 RFC 7184

Internet Engineering Task Force                               U. Herberg
Internet-Draft                           Fujitsu Laboratories of America
Intended status: Standards Track                                 R. Cole
Expires: October 10, 2013                                 US Army CERDEC
                                                              T. Clausen
                                                LIX, Ecole Polytechnique
                                                           April 8, 2013


  Definition of Managed Objects for the  Optimized Link State Routing
                           Protocol version 2
                     draft-ietf-manet-olsrv2-mib-06

Abstract

   This document defines the Management Information Base (MIB) module
   for configuring and managing the Optimized Link State Routing
   protocol version 2 (OLSRv2).  The OLSRv2-MIB module is structured
   into state information, performance metrics, and notifications.  This
   additional state and performance information is useful to
   troubleshoot problems and performance issues of the routing protocol.
   Different levels of compliance allow implementers to use smaller
   subsets of all defined objects, allowing for this MIB module to be
   deployed on more constrained routers.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on October 10, 2013.

Copyright Notice

   Copyright (c) 2013 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal



Herberg, et al.         Expires October 10, 2013                [Page 1]

Internet-Draft               The OLSRv2-MIB                   April 2013


   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
   2.  The Internet-Standard Management Framework . . . . . . . . . .  3
   3.  Conventions  . . . . . . . . . . . . . . . . . . . . . . . . .  3
   4.  Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .  3
     4.1.  Terms  . . . . . . . . . . . . . . . . . . . . . . . . . .  4
   5.  Structure of the MIB Module  . . . . . . . . . . . . . . . . .  4
     5.1.  The Configuration Group  . . . . . . . . . . . . . . . . .  5
     5.2.  The State Group  . . . . . . . . . . . . . . . . . . . . .  5
     5.3.  The Performance Group  . . . . . . . . . . . . . . . . . .  5
     5.4.  The Notifications Group  . . . . . . . . . . . . . . . . .  5
     5.5.  Tables and Indexing  . . . . . . . . . . . . . . . . . . .  6
   6.  Relationship to Other MIB Modules  . . . . . . . . . . . . . .  8
     6.1.  Relationship to the SNMPv2-MIB . . . . . . . . . . . . . .  8
     6.2.  Relationship to the NHDP-MIB . . . . . . . . . . . . . . .  8
     6.3.  MIB modules required for IMPORTS . . . . . . . . . . . . .  9
   7.  Definitions  . . . . . . . . . . . . . . . . . . . . . . . . .  9
   8.  Security Considerations  . . . . . . . . . . . . . . . . . . . 69
   9.  Applicability Statement  . . . . . . . . . . . . . . . . . . . 71
   10. IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 73
   11. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 73
   12. References . . . . . . . . . . . . . . . . . . . . . . . . . . 73
     12.1. Normative References . . . . . . . . . . . . . . . . . . . 73
     12.2. Informative References . . . . . . . . . . . . . . . . . . 74
   Appendix A.  Note to the RFC Editor  . . . . . . . . . . . . . . . 75
















Herberg, et al.         Expires October 10, 2013                [Page 2]

Internet-Draft               The OLSRv2-MIB                   April 2013


1.  Introduction

   This document defines the Management Information Base (MIB) module
   for configuring and managing the Optimized Link State Routing
   protocol version 2 (OLSRv2).  The OLSRv2-MIB module is structured
   into state information, performance metrics, and notifications.  In
   addition to configuration, this additional state and performance
   information is useful to troubleshoot problems and performance issues
   of the routing protocol.  Different levels of compliance allow
   implementers to use smaller subsets of all defined objects, allowing
   for this MIB module to be deployed on more constrained routers.

2.  The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to Section 7 of
   [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB module are defined using the mechanisms defined in
   the Structure of Management Information (SMI).  This document
   specifies a MIB module that is compliant to the SMIv2, which is
   described in [RFC2578], [RFC2579], and [RFC2580].

3.  Conventions

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   [RFC2119].

4.  Overview

   The Optimized Link State Routing Protocol version 2 (OLSRv2) [OLSRv2]
   is a table driven, proactive routing protocol, i.e., it exchanges
   topology information with other routers in the network periodically.
   OLSRv2 is an optimization of the classical link state routing
   protocol.  Its key concept is that of MultiPoint Relays (MPRs).  Each
   router selects a set of its neighbor routers (which "cover" all of
   its symmetrically connected 2-hop neighbor routers) as MPRs.  MPRs
   are then used to achieve both flooding reduction and topology
   reduction.

   This document provides management and control capabilities of an
   OLSRv2 instance, allowing to monitor the state and performance of an
   OLSRV2 router, as well as to change settings of the OLSRv2 instance



Herberg, et al.         Expires October 10, 2013                [Page 3]

Internet-Draft               The OLSRv2-MIB                   April 2013


   (e.g., router or interface parameters such as message intervals
   etc.).

   As OLSRv2 relies on the neighborhood information discovered by the
   "Mobile Ad Hoc Network (MANET) Neighborhood Discovery Protocol
   (NHDP)" [RFC6130], the OLSRv2-MIB module is aligned with the NHDP-MIB
   [RFC6779] module and augments several of the tables and objects in
   the NHDP-MIB.  In particular, common indexes for router interfaces
   and discovered neighbors are used, as described in Section 5.2.

4.1.  Terms

   The following definitions apply throughout this document:

   o  Configuration Objects - switches, tables, objects which are
      initialized to default settings or set through the management
      interface defined by this MIB module.

   o  State Objects - automatically generated values which define the
      current operating state of the OLSRv2 protocol process in the
      router.

   o  Performance Objects - automatically generated values which help an
      administrator or automated tool to assess the performance of the
      OLSRv2 routing process on the router.

   o  Notification Objects - define triggers and associated notification
      messages allowing for asynchronous tracking of pre-defined events
      on the managed router.

5.  Structure of the MIB Module

   This section presents the structure of the OLSRv2-MIB module.  The
   objects are arranged into the following structure:

   o  olsrv2Objects - defines objects forming the basis for the OLSRv2-
      MIB module.  These objects are divided up by function into the
      following groups:

      *  Configuration Group - defining objects related to the
         configuration of the OLSRv2 instance on the router.

      *  State Group - defining objects which reflect the current state
         of the OLSRv2 instance running on the router.

      *  Performance Group -defining objects which are useful to a
         management station when characterizing the performance of
         OLSRv2 on the router and in the MANET.



Herberg, et al.         Expires October 10, 2013                [Page 4]

Internet-Draft               The OLSRv2-MIB                   April 2013


   o  olsrv2Notifications - objects defining OLSRv2-MIB module
      notifications.

   o  olsrv2Conformance - defining the minimal and maximal conformance
      requirements for implementations of this MIB module.

5.1.  The Configuration Group

   The OLSRv2 router is configured with a set of controls.  The
   authoritative list of configuration controls within the OLSRv2-MIB
   module are found within the MIB module itself.  Generally, an attempt
   was made in developing the OLSRv2-MIB module to support all
   configuration objects defined in [OLSRv2].  For all of the
   configuration parameters, the same constraints and default values of
   these parameters as defined in [OLSRv2] are followed.

5.2.  The State Group

   The State Group reports current state information of a router running
   [OLSRv2].  The OLSRv2-MIB module State Group tables were designed to
   contain the complete set of state information defined within the
   information bases in [OLSRv2].

   The OLSRv2-MIB module State Group tables are constructed as
   extensions to the corresponding tables within the State Group of the
   NHDP-MIB [RFC6779] module.  Use of the AUGMENTS clause is made, when
   possible, to accomplish these table extensions.  Further, the State
   Group tables defined in this MIB module are aligned with the
   according tables in the NHDP-MIB [RFC6779] module, as described in
   Section 6.2.

5.3.  The Performance Group

   The Performance Group reports values relevant to system performance.
   Frequent changes of sets or frequent recalculation of the routing set
   or the MPRs can have a negative influence on the performance of
   OLSRv2.  This MIB module defines several objects that can be polled
   in order to, e.g., calculate histories or monitor frequencies of
   changes.  This may help the network administrator to determine
   unusual topology changes or other changes that affect stability and
   reliability of the MANET.  One such framework is specified in REPORT-
   MIB [REPORT-MIB].

5.4.  The Notifications Group

   The Notifications sub-tree contains the list of notifications
   supported within the OLSRv2-MIB module and their intended purpose or
   utility.



Herberg, et al.         Expires October 10, 2013                [Page 5]

Internet-Draft               The OLSRv2-MIB                   April 2013


   The same mechanisms for improving the network performance by reducing
   the number of notifications apply as defined in Section 5.1 of
   [RFC6779].  The following objects are used to define the thresholds
   and time windows for specific notifications defined in the NHDP-MIB
   module: olsrv2RoutingSetRecalculationCountThreshold,
   olsrv2RoutingSetRecalculationCountWindow,
   olsrv2MPRSetRecalculationCountThreshold, and
   olsrv2MPRSetRecalculationCountWindow.

   The Notifications Group contains Control, Objects and States, where
   the Control contains definitions of objects to control the frequency
   of notifications being sent.  The Objects define the supported
   notifications and the State is used to define additional information
   to be carried within the notifications.

5.5.  Tables and Indexing

   The OLSRv2-MIB module's tables are indexed via the following
   constructs:

   o  nhdpIfIndex - the ifIndex of the local router on which NHDP is
      configured.  This is defined in the NHDP-MIB.

   o  nhdpDiscIfIndex - a locally managed index representing a known
      interface on a neighboring router.  This is defined in the NHDP-
      MIB.

   o  nhdpDiscRouterIndex - a locally managed index representing an ID
      of a known neighboring router.  This is defined in the NHDP-MIB.

   o  olsrv2LibOrigSetIpAddrType and olsrv2LibOrigSetIpAddr - a recently
      used originator address by this router, and its type and prefix
      length.

   o  olsrv2LibLocAttNetSetIpAddrType, olsrv2LibLocAttNetSetIpAddr and
      olsrv2LibLocAttNetSetIpAddrPrefixLen - the network address of an
      attached network which can be reached via this router, and its
      type and its prefix length.

   o  olsrv2TibAdRemoteRouterSetRouterId - this is an additional index
      for each Remote Router's IfAddr associated with the
      olsrv2TibAdRemoteRouterSetIpAddr.

   o  olsrv2TibRouterTopologySetFromOrigIpAddrType and
      olsrv2TibRouterTopologySetFromOrigIpAddr - this is the originator
      address of a router which can reach the router with originator
      address TR_to_orig_addr in one hop.




Herberg, et al.         Expires October 10, 2013                [Page 6]

Internet-Draft               The OLSRv2-MIB                   April 2013


   o  olsrv2TibAttNetworksSetNetIpAddrType,
      olsrv2TibAttNetworksSetNetIpAddr and
      olsrv2TibAttNetworksSetNetIpAddrPrefixLen - this is is the network
      address of an attached network, which may be reached via the
      router with originator address AN_orig_addr.

   o  olsrv2TibRoutingSetDestIpAddrType, olsrv2TibRoutingSetDestIpAddr
      and olsrv2TibRoutingSetDestIpAddrPrefixLen - this is the address
      of the destination, either the address of an interface of a
      destination router, or the network address of an attached network.

   These tables and their indexing are:

   o  olsrv2InterfaceTable - describes the OLSRv2 status on the NHDP
      interfaces of this router.  This table has AUGMENTS {
      nhdpInterfaceEntry } and as such it is indexed via the nhdpIfIndex
      from the NHDP-MIB.

   o  olsrv2IibLinkSetTable - records all links from other routers which
      are, or recently were, 1-hop neighbors.  This table has AUGMENTS {
      nhdpIibLinkSetEntry } and as such it is indexed via the set
      nhdpIfIndex and nhdpDiscIfIndex.

   o  olsrv2Iib2HopSetTable - records network addresses of symmetric
      2-hop neighbors and the links to the associated 1-hop neighbors.
      This table has AUGMENTS { nhdpIib2HopSetEntry } and as such it is
      indexed via the set nhdpIfIndex, nhdpDiscIfIndex,
      nhdpIib2HopSetIpAddressType and nhdpIib2HopSetIpAddress.

   o  olsrv2LibOrigSetTable - records addresses that were recently used
      as originator addresses by this router.  This table has INDEX {
      olsrv2LibOrigSetIndex }.

   o  olsrv2LibLocAttNetSetTable - records its local non-OLSRv2
      interfaces via which it can act as gateways to other networks.
      This table has INDEX { olsrv2LibLocAttNetSetIndex }.

   o  olsrv2NibNeighborSetTable - records all network addresses of each
      1-hop neighbor.  This table has AUGMENTS { nhdpNibNeighborSetEntry
      } and as such it is indexed via the nhdpDiscRouterIndex.

   o  olsrv2TibAdRemoteRouterSetTable - records information describing
      each remote router in the network that transmits TC messages.
      This table has INDEX { olsrv2TibAdRemoteRouterSetRouterId }.

   o  olsrv2TibRouterTopologySetTable - records topology information
      about the network.  This table has INDEX {
      olsrv2TibRouterTopologySetIndex }.



Herberg, et al.         Expires October 10, 2013                [Page 7]

Internet-Draft               The OLSRv2-MIB                   April 2013


   o  olsrv2TibRoutableAddressTopologySetTable - records topology
      information about the routable addresses within the MANET, and via
      which routers they may be reached.  This table has INDEX
      {olsrv2TibRoutableAddressTopologySetIndex }.

   o  olsrv2TibAttNetworksSetTable - records information about networks
      (which may be outside the MANET) attached to other routers and
      their routable addresses.  This table has INDEX {
      olsrv2TibAttNetworksSetIndex }.

   o  olsrv2TibRoutingSetTable - records the first hop along a selected
      path to each destination for which any such path is known.  This
      table has INDEX { olsrv2TibRoutingSetDestIpAddrType,
      olsrv2TibRoutingSetDestIpAddr,
      olsrv2TibRoutingSetDestIpAddrPrefLen}.

   o  olsrv2InterfacePerfTable - records performance counters for each
      active OLSRv2 interface on this device. selected path to each
      destination for which any such path is known.  This table has
      AUGMENTS { nhdpInterfacePerfEntry } and as such it is indexed via
      nhdpIfIndex from the NHDP-MIB.

6.  Relationship to Other MIB Modules

   This section specifies the relationship of the MIB modules contained
   in this document to other standards, particularly to standards
   containing other MIB modules.  MIB modules and specific definitions
   imported from MIB modules that SHOULD be implemented in conjunction
   with the MIB module contained within this document are identified in
   this section.

6.1.  Relationship to the SNMPv2-MIB

   The System group in the SNMPv2-MIB [RFC3418] module is defined as
   being mandatory for all systems, and the objects apply to the entity
   as a whole.  The System group provides identification of the
   management entity and certain other system-wide data.  The OLSRv2-MIB
   module does not duplicate those objects.

6.2.  Relationship to the NHDP-MIB

   OLSRv2 depends on the neighborhood information that is discovered by
   [RFC6130].  In order access the Objects relating to discovered
   neighbors, the State Group tables of the NHDP-MIB [RFC6779] module
   are aligned with this MIB module.  This is accomplished through the
   use of the AUGMENTS capability of SMIv2 and the definition of
   TEXTUAL-CONVENTIONS in the NHDP-MIB module: specifically the
   NeighborRouterIndex.  These object types are used to develop indexes



Herberg, et al.         Expires October 10, 2013                [Page 8]

Internet-Draft               The OLSRv2-MIB                   April 2013


   into common NHDP-MIB module and routing protocol State Group tables.
   These objects are locally significant but should be locally common to
   the NHDP-MIB module and the OLSRv2-MIB module implemented on a common
   networked router.  This will allow for improved cross referencing of
   information across the two MIB modules.

6.3.  MIB modules required for IMPORTS

   The following OLSRv2-MIB module IMPORTS objects from NHDP-MIB
   [RFC6779], SNMPv2-SMI [RFC2578], SNMPv2-TC [RFC2579], SNMPv2-CONF
   [RFC2580], IF-MIB [RFC2863], INET-ADDRESS-MIB [RFC4001] and FLOAT-TC-
   MIB [RFC6340].

7.  Definitions

   This section contains the OLSRv2-MIB module defined by the
   specification.


    OLSRv2-MIB DEFINITIONS ::= BEGIN

    -- This MIB module defines objects for the management of
    -- RFC XXXX - The Optimized Link State Routing Protocol
    -- version 2, Clausen, T., Dearlove, C., Jacquet, P.
    -- and U. Herberg, March 2013.

    IMPORTS

       MODULE-IDENTITY, OBJECT-TYPE, Counter32, Counter64,
       Integer32, Unsigned32, mib-2, TimeTicks,
       NOTIFICATION-TYPE
                FROM SNMPv2-SMI -- RFC 2578

       TEXTUAL-CONVENTION, TimeStamp, TruthValue
                FROM SNMPv2-TC -- RFC 2579

       MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
                FROM SNMPv2-CONF -- STD 58

       InetAddressType, InetAddress,
       InetAddressPrefixLength
                FROM INET-ADDRESS-MIB -- RFC 3291

       Float32TC
                FROM FLOAT-TC-MIB  -- RFC 6340

       NeighborRouterIndex, nhdpInterfaceEntry,
       nhdpIibLinkSetEntry, nhdpIib2HopSetEntry,



Herberg, et al.         Expires October 10, 2013                [Page 9]

Internet-Draft               The OLSRv2-MIB                   April 2013


       nhdpNibNeighborSetEntry, nhdpInterfacePerfEntry
                FROM NHDP-MIB -- RFC 6779
       ;

    manetOlsrv2MIB MODULE-IDENTITY
       LAST-UPDATED "201304081000Z"   -- 08 April 2013
       ORGANIZATION "IETF MANET Working Group"
       CONTACT-INFO
          "WG E-Mail: manet@ietf.org

           WG Chairs: sratliff@cisco.com
                      jmacker@nrl.navy.mil


           Editors:   Ulrich Herberg
                      Fujitsu Laboratories of America
                      1240 East Arques Avenue
                      Sunnyvale, CA 94085
                      USA
                      ulrich@herberg.name
                      http://www.herberg.name/

                      Thomas Heide Clausen
                      Ecole Polytechnique
                      LIX
                      91128 Palaiseau Cedex
                      France
                      http://www.thomasclausen.org/
                      T.Clausen@computer.org

                      Robert G. Cole
                      US Army CERDEC
                      Space and Terrestrial Communications
                      6010 Frankford Street
                      Bldg 6010, Room 453H
                      Aberdeen Proving Ground, MD 21005
                      USA
                      +1 443 395-8744
                      robert.g.cole@us.army.mil
                      http://www.cs.jhu.edu/~rgcole/"

       DESCRIPTION
          "This OLSRv2-MIB module is applicable to routers
           implementing the Optimized Link State Routing Protocol
           version 2 (OLSRv2) defined in RFC XXXX.

           Copyright (c) 2013 IETF Trust and the persons
           identified as authors of the code.  All rights reserved.



Herberg, et al.         Expires October 10, 2013               [Page 10]

Internet-Draft               The OLSRv2-MIB                   April 2013


           Redistribution and use in source and binary forms, with
           or without modification, is permitted pursuant to, and
           subject to the license terms contained in, the Simplified
           BSD License set forth in Section 4.c of the IETF Trust's
           Legal Provisions Relating to IETF Documents
           (http://trustee.ietf.org/license-info).

           This version of this MIB module is part of RFC YYYY; see
           the RFC itself for full legal notices."

         -- Revision History
         REVISION    "201304081000Z"   -- 08 April 2013
         DESCRIPTION
          "Initial version of this MIB module,
           published as RFC YYYY."

         -- RFC-Editor assigns ZZZZ (this comment can be removed)
         ::= { mib-2 ZZZZ }


 --
 -- TEXTUAL CONVENTIONS
 --

 Olsrv2Status ::= TEXTUAL-CONVENTION
    STATUS      current
    DESCRIPTION
       "An indication of the operability of the OLSRv2
        protocol on the device or a specific interface.
        For example, the status
        of an interface: 'enabled' indicates that
        it is performing OLSRv2 operation,
        and 'disabled' indicates that it is not."
    SYNTAX      INTEGER {
       enabled (1),
       disabled (2)
    }


 --
 -- Top-Level Object Identifier Assignments
 --

 olsrv2MIBNotifications OBJECT IDENTIFIER ::= { manetOlsrv2MIB 0 }
 olsrv2MIBObjects       OBJECT IDENTIFIER ::= { manetOlsrv2MIB 1 }
 olsrv2MIBConformance   OBJECT IDENTIFIER ::= { manetOlsrv2MIB 2 }

 --



Herberg, et al.         Expires October 10, 2013               [Page 11]

Internet-Draft               The OLSRv2-MIB                   April 2013


 -- olsrv2ConfigurationGroup
 --

 --    Contains the OLSRv2 objects that configure specific
 --    options that determine the overall performance and operation
 --    of the OLSRv2 routing process.

 olsrv2ConfigurationGroup OBJECT IDENTIFIER ::= {olsrv2MIBObjects 1}


    olsrv2AdminStatus  OBJECT-TYPE
       SYNTAX      Olsrv2Status
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "The configured status of the OLSRv2 process
           on this device.  'enabled(1)' means that
           OLSRv2 is configured to run on this device.
           'disabled(2)' mean that the OLSRv2 process
           is configured off.

           Operation of the OLSRv2 routing protocol
           requires the operation of the Neighborhood
           Discovery Protocol (RFC 6130).  Hence, this
           object cannot have a status of 'enabled'
           unless at least one interface an the device
           is a MANET interface with NHDP enabled on that
           interface.  If all device interfaces running
           NHDP become disabled or removed, then the
           olsrv2AdminStatus MUST be set to 'disabled'.

           If the network manager sets this object to
           'disabled', then the associated interface specific
           objects, i.e., the olsrv2InterfaceAdminStatus
           objects must all be set to 'disabled'.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       DEFVAL { disabled }
    ::= { olsrv2ConfigurationGroup 1 }

    olsrv2InterfaceTable  OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2InterfaceEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The olsrv2InterfaceTable describes the



Herberg, et al.         Expires October 10, 2013               [Page 12]

Internet-Draft               The OLSRv2-MIB                   April 2013


           OLSRv2 status on the NHDP interfaces of this router.
           As such, this table AUGMENTS the nhdpInterfaceTable
           defined in the NHDP-MIB (RFC 6779). NHDP interfaces
           are explicitly defined by network manager servers
           for interfaces on the device that are intended to
           run MANET protocols.  The olsrv2InterfaceTable
           contains a single boolean object, the
           olsrv2InterfaceAdminStatus object.

           A conceptual row in this table exists if and only
           if either a manager has explicitly created the row
           in the nhdpInterfaceTable
           or there is an interface on the managed device
           that supports and runs NHDP.

           If the corresponding entry with nhdpIfIndex value
           is deleted from the nhdpInterfaceTable, then the entry
           in this table is automatically deleted and
           OLSRv2 is disabled on this interface,
           and all configuration and state information
           related to this interface is to be removed
           from memory.

           The olsrv2InterfaceAdminStatus can only be
           'enabled' if the corresponding olsrv2AdminStatus
           object is also set to 'enabled'."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2ConfigurationGroup 2 }

    olsrv2InterfaceEntry OBJECT-TYPE
       SYNTAX      Olsrv2InterfaceEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The olsrv2InterfaceEntry describes one OLSRv2
           local interface configuration as indexed by
           its nhdpIfIndex as defined in the
           NHDP-MIB (RFC 6779).

           The objects in this table are persistent and when
           written the device SHOULD save the change to
           non-volatile storage.  For further information
           on the storage behavior for these objects, refer
           to the description for the nhdpIfRowStatus
           object in the NHDP-MIB (RFC6779)."



Herberg, et al.         Expires October 10, 2013               [Page 13]

Internet-Draft               The OLSRv2-MIB                   April 2013


       REFERENCE
          "RFC 6779 - The Neighborhood Discovery Protocol MIB,
           Herberg, U., Cole, R.G. and I. Chakeres,
           October 2012"
       AUGMENTS { nhdpInterfaceEntry }
    ::= { olsrv2InterfaceTable 1 }

    Olsrv2InterfaceEntry ::=
       SEQUENCE {
          olsrv2InterfaceAdminStatus
             Olsrv2Status
       }

    olsrv2InterfaceAdminStatus OBJECT-TYPE
       SYNTAX      Olsrv2Status
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
          "The OLSRv2 interface's administrative status.
           The value 'enabled' denotes that the interface
           is running the OLSRv2 routing process.
           The value 'disabled' denotes that the interface is
           external to the OLSRv2 routing process.

           The configuration objects for the OLSRv2 routing
           process, other than the administrative status objects,
           are common to all interfaces on this device.
           As such, the OLSRv2 configuration objects are globally
           defined for the device and are not contained within
           the olsrv2InterfaceTable."
       DEFVAL { disabled }
    ::= { olsrv2InterfaceEntry 1 }

    olsrv2OrigIpAddrType  OBJECT-TYPE
        SYNTAX      InetAddressType
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
           "The type of the olsrv2OrigIpAddr, as defined
            in the InetAddress MIB module (RFC 4001).

            Only the values 'ipv4(1)' and
            'ipv6(2)' are supported."
        REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2ConfigurationGroup 3 }



Herberg, et al.         Expires October 10, 2013               [Page 14]

Internet-Draft               The OLSRv2-MIB                   April 2013


    olsrv2OrigIpAddr  OBJECT-TYPE
        SYNTAX      InetAddress (SIZE(4|16))
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
           "The router's originator address. An address that
            is unique (within the MANET) to this router.

            This object is persistent and when written
            the entity SHOULD save the change to
            non-volatile storage."
        REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2ConfigurationGroup 4 }

    --
    -- Local History Times
    --

    olsrv2OHoldTime  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2OHoldTime corresponds to
          O_HOLD_TIME of OLSRv2 and represents the
          time for which a recently used and replaced
          originator address is used to recognize the router's
          own messages.

          Guidance for setting this object may be found
          in Section 5 of the OLSRv2 specification (RFC XXXX),
          which indicates that:
              o  olsrv2OHoldTime > 0

          This object is persistent and when written
          the entity SHOULD save the change to
          non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 30000 }
    ::= { olsrv2ConfigurationGroup 5 }



Herberg, et al.         Expires October 10, 2013               [Page 15]

Internet-Draft               The OLSRv2-MIB                   April 2013


    --
    -- Message intervals
    --

    olsrv2TcInterval  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2TcInterval corresponds to
          TC_INTERVAL of OLSRv2 and represents the
          maximum time between the transmission of
          two successive TC messages by this router.

          Guidance for setting this object may be found
          in Section 5 of the OLSRv2 specification (RFC XXXX),
          which indicates that:

              o olsrv2TcInterval > 0
              o olsrv2TcInterval >= olsrv2TcMinInterval

          This object is persistent and when written
          the entity SHOULD save the change to
          non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 5000 }
    ::= { olsrv2ConfigurationGroup 6 }

    olsrv2TcMinInterval  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2TcMinInterval corresponds to
          TC_MIN_INTERVAL of OLSRv2 and represents
          the minimum interval between transmission of
          two successive TC messages by this router.

          Guidance for setting this object may be found
          in Section 5 of the OLSRv2 specification (RFC XXXX),
          which indicates that:
              o olsrv2TcInterval >= olsrv2TcMinInterval



Herberg, et al.         Expires October 10, 2013               [Page 16]

Internet-Draft               The OLSRv2-MIB                   April 2013


          This object is persistent and when written
          the entity SHOULD save the change to
          non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 1250 }
    ::= { olsrv2ConfigurationGroup 7 }


    --
    -- Advertised information validity times
    --

    olsrv2THoldTime  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2THoldTime corresponds to
          T_HOLD_TIME of OLSRv2 and is used as the
          minimum value in the TLV with
          Type = VALIDITY_TIME included in all
          TC messages sent by this router.

          Guidance for setting this object may be found
          in Section 5 of the OLSRv2 specification (RFC XXXX),
          which indicates that:
              o olsrv2THoldTime >= olsrv2TcInterval
              o If TC messages can be lost, then
                olsrv2THoldTime should be
                significantly greater than olsrv2TcInterval;
                a value >= 3 x olsrv2TcInterval is recommended.

          olsrv2THoldTime MUST be representable by way of the
          exponent-mantissa notation as described in RFC 5497.

          This object is persistent and when written
          the entity SHOULD save the change to
          non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."



Herberg, et al.         Expires October 10, 2013               [Page 17]

Internet-Draft               The OLSRv2-MIB                   April 2013


       DEFVAL { 15000 }
    ::= { olsrv2ConfigurationGroup 8 }

    olsrv2AHoldTime  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2AHoldTime corresponds to
          A_HOLD_TIME of OLSRv2 and represents
          the period during which TC messages are sent
          after they no longer have any advertised
          information to report, but are sent in order
          to accelerate outdated information removal by other routers.

          Guidance for setting this object may be found
          in Section 5 of the OLSRv2 specification (RFC XXXX),
          which indicates that:
             o If TC messages can be lost, then
               olsrv2AHoldTime should be
               significantly greater than olsrv2TcInterval;
               a value >= 3 x olsrv2TcInterval is
               recommended.

          olsrv2AHoldTime MUST be representable by way
          of the exponent-mantissa notation as
          described in RFC 5497.

          This object is persistent and when written
          the entity SHOULD save the change to
          non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 15000 }
    ::= { olsrv2ConfigurationGroup 9 }

    --
    -- Received message validity times
    --

    olsrv2RxHoldTime  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write



Herberg, et al.         Expires October 10, 2013               [Page 18]

Internet-Draft               The OLSRv2-MIB                   April 2013


       STATUS      current
       DESCRIPTION
          "olsrv2RxHoldTime corresponds to
           RX_HOLD_TIME of OLSRv2 and represents the period
           after receipt of a message by the appropriate OLSRv2
           interface of this router for which that information
           is recorded, in order that the message is recognized
           as having been previously received on this OLSRv2
           interface.

           Guidance for setting this object may be found
           in Section 5 of the OLSRv2 specification (RFC XXXX),
           which indicates that:
              o olsrv2RxHoldTime > 0
              o This parameter should be greater
                than the maximum difference in time that a
                message may take to traverse the MANET,
                taking into account any message forwarding
                jitter as well as propagation, queuing,
                and processing delays.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 30000 }
    ::= { olsrv2ConfigurationGroup 10 }

    olsrv2PHoldTime  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2PHoldTime corresponds to
           P_HOLD_TIME of OLSRv2 and represents the period
           after receipt of a message that is processed by
           this router for which that information is recorded,
           in order that the message is not processed again
           if received again.

           Guidance for setting this object may be found
           in Section 5 of the OLSRv2 specification (RFC XXXX),
           which indicates that:



Herberg, et al.         Expires October 10, 2013               [Page 19]

Internet-Draft               The OLSRv2-MIB                   April 2013


              o olsrv2PHoldTime > 0
              o This parameter should be greater
                than the maximum difference in time that a
                message may take to traverse the MANET,
                taking into account any message forwarding
                jitter as well as propagation, queuing,
                and processing delays.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 30000 }
    ::= { olsrv2ConfigurationGroup 11 }

    olsrv2FHoldTime  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2FHoldTime corresponds to
           F_HOLD_TIME of OLSRv2 and represents the period
           after receipt of a message that is forwarded by this
           router for which that information is recorded, in order
           that the message is not forwarded again if received again.

           Guidance for setting this object may be found
           in Section 5 of the OLSRv2 specification (RFC XXXX),
           which indicates that:
              o olsrv2FHoldTime > 0
              o This parameter should be greater
                than the maximum difference in time that a
                message may take to traverse the MANET,
                taking into account any message forwarding
                jitter as well as propagation, queuing,
                and processing delays.

           This parameter SHOULD be greater
           than the maximum difference in time that a
           message may take to traverse the MANET,
           taking into account any message forwarding
           jitter as well as propagation, queuing,
           and processing delays.



Herberg, et al.         Expires October 10, 2013               [Page 20]

Internet-Draft               The OLSRv2-MIB                   April 2013


           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 30000 }
    ::= { olsrv2ConfigurationGroup 12 }


    --
    -- Jitter times
    --

    olsrv2TpMaxJitter  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2TpMaxJitter corresponds to
           TP_MAXJITTER of OLSRv2 and represents the value
           of MAXJITTER used in RFC5148 for periodically
           generated TC messages sent by this router.

           For constraints on these parameters see RFC 5148.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 500 }
    ::= { olsrv2ConfigurationGroup 13 }

    olsrv2TtMaxJitter  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2TtMaxJitter corresponds to
           TT_MAXJITTER of OLSRv2 and represents the value



Herberg, et al.         Expires October 10, 2013               [Page 21]

Internet-Draft               The OLSRv2-MIB                   April 2013


           of MAXJITTER used in RFC5148 for externally
           triggered TC messages sent by this router.

           For constraints on these parameters see RFC 5148.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 500 }
    ::= { olsrv2ConfigurationGroup 14 }


    olsrv2FMaxJitter  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2FMaxJitter corresponds to
           F_MAXJITTER of OLSRv2 and represents the
           default value of MAXJITTER used in RFC 5148 for
           messages forwarded by this router.

           For constraints on these parameters see RFC 5148.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 500 }
    ::= { olsrv2ConfigurationGroup 15 }


    --
    -- Hop limits
    --

    olsrv2TcHopLimit  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..255)



Herberg, et al.         Expires October 10, 2013               [Page 22]

Internet-Draft               The OLSRv2-MIB                   April 2013


       UNITS       "hops"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2TcHopLimit corresponds to
           TC_HOP_LIMIT of OLSRv2.

           Guidance for setting this object may be found
           in Section 5 of the OLSRv2 specification (RFC XXXX),
           which indicates that:
              o The maximum value of
                olsrv2TcHopLimit >= the network diameter
               in hops, a value of 255 is recommended.
              o All values of olsrv2TcHopLimit >= 2.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
        REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
        DEFVAL { 255 }
    ::= { olsrv2ConfigurationGroup 16 }


    --
    -- Willingness
    --

    olsrv2WillRouting  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..15)
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2WillRouting corresponds to
           WILL_ROUTING of OLSRv2.

           Guidance for setting this object may be found
           in Section 5 of the OLSRv2 specification (RFC XXXX),
           which indicates that:
              o WILL_NEVER (0) <= olsrv2WillRouting <=
                                   WILL_ALWAYS (15)

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."



Herberg, et al.         Expires October 10, 2013               [Page 23]

Internet-Draft               The OLSRv2-MIB                   April 2013


       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 7 }
    ::= { olsrv2ConfigurationGroup 17 }


    olsrv2WillFlooding     OBJECT-TYPE
       SYNTAX      Unsigned32 (0..15)
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2WillFlooding corresponds to
           WILL_FLOODING of OLSRv2.

           Guidance for setting this object may be found
           in Section 5 of the OLSRv2 specification (RFC XXXX),
           which indicates that:
              o WILL_NEVER (0) <= olsrv2WillFlooding <=
                                   WILL_ALWAYS (15)

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 7 }
    ::= { olsrv2ConfigurationGroup 18 }


    olsrv2LinkMetricType  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..255)
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2LinkMetricType corresponds to
           LINK_METRIC_TYPE of OLSRv2.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.



Herberg, et al.         Expires October 10, 2013               [Page 24]

Internet-Draft               The OLSRv2-MIB                   April 2013


           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 0 }
    ::= { olsrv2ConfigurationGroup 19 }



 --
 -- olsrv2StateGroup
 --

 --
 -- Contains information describing the current state of
 -- the OLSRv2 process.
 --

 olsrv2StateGroup  OBJECT IDENTIFIER ::= { olsrv2MIBObjects 2 }

    --
    -- Interface Information Base (IIB)
    --

    --
    -- Link Set from RFC 6130, extended by L_in_metric,
    -- L_out_metric, and L_mpr_selector entries for each tuple
    --

    olsrv2IibLinkSetTable OBJECT-TYPE
       SYNTAX       SEQUENCE OF Olsrv2IibLinkSetEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
          "A Link Set of an interface records all links
           from other routers which are, or recently
           were, 1-hop neighbors."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 1 }

    olsrv2IibLinkSetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2IibLinkSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A Link Set consists of Link Tuples, each



Herberg, et al.         Expires October 10, 2013               [Page 25]

Internet-Draft               The OLSRv2-MIB                   April 2013


           representing a single link indexed by the
           local and remote interface pair. Each Link Set
           from NHDP is extended by OLSRv2 by the following
           fields:

           (L_in_metric, L_out_metric, L_mpr_selector)"
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       AUGMENTS { nhdpIibLinkSetEntry }
    ::= { olsrv2IibLinkSetTable 1 }

    Olsrv2IibLinkSetEntry ::=
       SEQUENCE {
          olsrv2IibLinkSetInMetric
             Float32TC,
          olsrv2IibLinkSetOutMetric
             Float32TC,
          olsrv2IibLinkSetMprSelector
             TruthValue
       }

    olsrv2IibLinkSetInMetric  OBJECT-TYPE
       SYNTAX      Float32TC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "olsrv2IibLinkSetInMetric is the metric of the link
           from the OLSRv2 interface with addresses
           L_neighbor_iface_addr_list to this OLSRv2 interface."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2IibLinkSetEntry 1 }

    olsrv2IibLinkSetOutMetric  OBJECT-TYPE
       SYNTAX      Float32TC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "olsrv2IibLinkSetInMetric is the metric of the
           link to the OLSRv2 interface with addresses
           L_neighbor_iface_addr_list from this OLSRv2 interface."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.



Herberg, et al.         Expires October 10, 2013               [Page 26]

Internet-Draft               The OLSRv2-MIB                   April 2013


           and U. Herberg, March 2013."
    ::= { olsrv2IibLinkSetEntry 2 }

    olsrv2IibLinkSetMprSelector  OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "olsrv2IibLinkSetMprSelector is a boolean flag,
           describing if this neighbor has selected this router
           as a flooding MPR, i.e., is a flooding MPR selector
           of this router."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2IibLinkSetEntry 3 }

    --
    -- 2-Hop Set; from RFC 6130, extended by OLSRv2 by the
    -- following fields: N2_in_metric, N2_out_metric
    --

    olsrv2Iib2HopSetTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2Iib2HopSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A 2-Hop Set of an interface records network
           addresses of symmetric 2-hop neighbors, and
           the symmetric links to symmetric 1-hop neighbors
           through which these symmetric 2-hop neighbors
           can be reached.  It consists of 2-Hop Tuples."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 2 }

    olsrv2Iib2HopSetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2Iib2HopSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "olsrv2Iib2HopSetTable consists of 2-Hop Tuples,
           each representing a single network address of
           a symmetric 2-hop neighbor, and a single MANET
           interface of a symmetric 1-hop neighbor.



Herberg, et al.         Expires October 10, 2013               [Page 27]

Internet-Draft               The OLSRv2-MIB                   April 2013


           Each 2-Hop Set from NHDP is extended by
           OLSRv2 by the following fields:

           (N2_in_metric, N2_out_metric)"
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       AUGMENTS { nhdpIib2HopSetEntry }
    ::= { olsrv2Iib2HopSetTable 1 }

    Olsrv2Iib2HopSetEntry ::=
       SEQUENCE {
          olsrv2Iib2HopSetInMetric
             Float32TC,
          olsrv2Iib2HopSetOutMetric
             Float32TC
       }

    olsrv2Iib2HopSetInMetric  OBJECT-TYPE
       SYNTAX      Float32TC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "olsrv2Iib2HopSetInMetric is the neighbor metric
           from the router with address N2_2hop_iface_addr
           to the router with OLSRv2 interface addresses
           N2_neighbor_iface_addr_list."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2Iib2HopSetEntry 1 }

    olsrv2Iib2HopSetOutMetric  OBJECT-TYPE
       SYNTAX      Float32TC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "olsrv2Iib2HopSetN2Time is the neighbor metric
           to the router with address N2_2hop_iface_addr
           from the router with OLSRv2 interface addresses
           N2_neighbor_iface_addr_list."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2Iib2HopSetEntry 2 }



Herberg, et al.         Expires October 10, 2013               [Page 28]

Internet-Draft               The OLSRv2-MIB                   April 2013


    --
    -- Local Information Base  - as defined in RFC 6130,
    -- extended by the addition of an Originator Set,
    -- defined in Section 6.1 and a Local Attached
    -- Network Set, defined in Section 6.2.
    --

    --
    -- Originator Set
    --

    olsrv2LibOrigSetTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2LibOrigSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A router's Originator Set records addresses
           that were recently used as originator addresses
           by this router."
        REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 3 }

    olsrv2LibOrigSetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2LibOrigSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A router's Originator Set consists of
           Originator Tuples:

           (O_orig_addr, O_time)"
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       INDEX { olsrv2LibOrigSetIndex }
    ::= { olsrv2LibOrigSetTable 1 }

    Olsrv2LibOrigSetEntry ::=
       SEQUENCE {
          olsrv2LibOrigSetIndex
             Integer32,
          olsrv2LibOrigSetIpAddrType
             InetAddressType,
          olsrv2LibOrigSetIpAddr



Herberg, et al.         Expires October 10, 2013               [Page 29]

Internet-Draft               The OLSRv2-MIB                   April 2013


             InetAddress,
          olsrv2LibOrigSetExpireTime
             TimeStamp
       }

    olsrv2LibOrigSetIndex  OBJECT-TYPE
       SYNTAX      Integer32 (0..65535)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The index for this table."
    ::= { olsrv2LibOrigSetEntry 1 }

    olsrv2LibOrigSetIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2LibOrigSetIpAddr,
           as defined in the InetAddress MIB (RFC4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2LibOrigSetEntry 2 }

    olsrv2LibOrigSetIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "A recently used originator address
           by this router."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2LibOrigSetEntry 3 }

    olsrv2LibOrigSetExpireTime  OBJECT-TYPE
       SYNTAX      TimeStamp
       UNITS      "milliseconds"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION



Herberg, et al.         Expires October 10, 2013               [Page 30]

Internet-Draft               The OLSRv2-MIB                   April 2013


          "olsrv2LibOrigSetExpireTime specifies the value
           of sysUptime when this entry should expire and be
           removed from the olsrv2LibOrigSetTable."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2LibOrigSetEntry 4 }


    --
    -- Local Attached Network Set
    --

    olsrv2LibLocAttNetSetTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2LibLocAttNetSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A router's Local Attached Network Set records
           its local non-OLSRv2 interfaces via which it
           can act as gateways to other networks."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 4 }

    olsrv2LibLocAttNetSetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2LibLocAttNetSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The entries include the Local Attached
           Network Tuples:

           (AL_net_addr, AL_dist, AL_metric)

           where:

              AL_net_addr is the network address
              of an attached network which can
              be reached via this router.

              AL_dist is the number of hops to
              the network with address AL_net_addr
              from this router.




Herberg, et al.         Expires October 10, 2013               [Page 31]

Internet-Draft               The OLSRv2-MIB                   April 2013


              AL_metric is the metric of the link to
              the attached network with address
              AL_net_addr from this router."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       INDEX { olsrv2LibLocAttNetSetIndex }
    ::= { olsrv2LibLocAttNetSetTable 1 }

    Olsrv2LibLocAttNetSetEntry ::=
       SEQUENCE {
          olsrv2LibLocAttNetSetIndex
             Integer32,
          olsrv2LibLocAttNetSetIpAddrType
             InetAddressType,
          olsrv2LibLocAttNetSetIpAddr
             InetAddress,
          olsrv2LibLocAttNetSetIpAddrPrefixLen
             InetAddressPrefixLength,
          olsrv2LibLocAttNetSetDistance
             Unsigned32,
          olsrv2LibLocAttNetSetMetric
             Float32TC
       }

    olsrv2LibLocAttNetSetIndex  OBJECT-TYPE
       SYNTAX      Integer32 (0..65535)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The index for this table."
    ::= { olsrv2LibLocAttNetSetEntry 1 }

    olsrv2LibLocAttNetSetIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2LibLocAttNetSetIpAddr, as defined
           in the InetAddress MIB (RFC 4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."



Herberg, et al.         Expires October 10, 2013               [Page 32]

Internet-Draft               The OLSRv2-MIB                   April 2013


    ::= { olsrv2LibLocAttNetSetEntry 2 }

    olsrv2LibLocAttNetSetIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the network address of an attached
           network which can be reached via this router."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2LibLocAttNetSetEntry 3 }

    olsrv2LibLocAttNetSetIpAddrPrefixLen  OBJECT-TYPE
       SYNTAX      InetAddressPrefixLength
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "Indicates the number of leading one bits that form the
           mask to be logically ANDed with the destination address
           before being compared to the value in the
           olsrv2LibLocAttNetSetIpAddr field."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2LibLocAttNetSetEntry 4 }

    olsrv2LibLocAttNetSetDistance  OBJECT-TYPE
       SYNTAX      Unsigned32 (1..255)
       UNITS       "hops"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object specifies the number of hops
           to the network with address
           olsrv2LibLocAttNetSetIpAddr from this router."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2LibLocAttNetSetEntry 5 }

    olsrv2LibLocAttNetSetMetric  OBJECT-TYPE
       SYNTAX      Float32TC
       MAX-ACCESS  read-only



Herberg, et al.         Expires October 10, 2013               [Page 33]

Internet-Draft               The OLSRv2-MIB                   April 2013


       STATUS      current
       DESCRIPTION
          "This object specifies the metric of the
           link to the attached network with
           address AL_net_addr from this router."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2LibLocAttNetSetEntry 6 }


    --
    -- Neighbor Information Base  - as defined in RFC 6130,
    -- extended by OLSRv2 by the addition of the following
    -- elements to each Neighbor Tuple
    --

    --
    -- Neighbor Set
    --

    olsrv2NibNeighborSetTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2NibNeighborSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A router's Neighbor Set records all network
           addresses of each 1-hop neighbor. It consists
           of Neighbor Tuples, each representing a single
           1-hop neighbor. "
        REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
     ::= { olsrv2StateGroup 5 }

     olsrv2NibNeighborSetEntry  OBJECT-TYPE
        SYNTAX      Olsrv2NibNeighborSetEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
           "Each Neighbor Tuple in the Neighbor Set, defined
            in RFC 6130, has these additional elements:
               N_orig_addr
               N_in_metric
               N_out_metric
               N_will_flooding



Herberg, et al.         Expires October 10, 2013               [Page 34]

Internet-Draft               The OLSRv2-MIB                   April 2013


               N_will_routing
               N_flooding_mpr
               N_routing_mpr
               N_mpr_selector
               N_advertised
            defined here as extensions."
        REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
        AUGMENTS { nhdpNibNeighborSetEntry }
    ::= { olsrv2NibNeighborSetTable 1 }

    Olsrv2NibNeighborSetEntry ::=
       SEQUENCE {
          olsrv2NibNeighborSetNOrigIpAddrType
             InetAddressType,
          olsrv2NibNeighborSetNOrigIpAddr
             InetAddress,
          olsrv2NibNeighborSetNInMetric
             Float32TC,
          olsrv2NibNeighborSetNOutMetric
             Float32TC,
          olsrv2NibNeighborSetNWillFlooding
             Unsigned32,
          olsrv2NibNeighborSetNWillRouting
             Unsigned32,
          olsrv2NibNeighborSetNFloodingMpr
             TruthValue,
          olsrv2NibNeighborSetNRoutingMpr
             TruthValue,
          olsrv2NibNeighborSetNMprSelector
             TruthValue,
          olsrv2NibNeighborSetNAdvertised
             TruthValue
       }

    olsrv2NibNeighborSetNOrigIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2NibNeighborSetNOrigIpAddr, as defined
           in the InetAddress MIB module (RFC4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE



Herberg, et al.         Expires October 10, 2013               [Page 35]

Internet-Draft               The OLSRv2-MIB                   April 2013


          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 1 }

    olsrv2NibNeighborSetNOrigIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the originator IP address of that
           neighbor."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 2 }

    olsrv2NibNeighborSetNInMetric  OBJECT-TYPE
       SYNTAX      Float32TC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is the neighbor metric of any
           link from this neighbor to an OLSRv2 interface
           of this router, i.e., the minimum of all corresponding
           L_in_metric with L_status = SYMMETRIC and
           L_in_metric != UNKNOWN_METRIC, UNKNOWN_METRIC
           if there are no such Link Tuples."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 3 }

    olsrv2NibNeighborSetNOutMetric  OBJECT-TYPE
       SYNTAX      Float32TC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is is the neighbor metric of any
           link from an OLSRv2 interface of this router
           to this neighbor, i.e., the minimum of
           all corresponding L_out_metric with
           L_status = SYMMETRIC and
           L_out_metric != UNKNOWN_METRIC, UNKNOWN_METRIC
           if there are no such Link Tuples."
       REFERENCE



Herberg, et al.         Expires October 10, 2013               [Page 36]

Internet-Draft               The OLSRv2-MIB                   April 2013


          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 4 }

    olsrv2NibNeighborSetNWillFlooding  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..15)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is the neighbor's willingness to be
           selected as a flooding MPR, in the range from
           WILL_NEVER to WILL_ALWAYS, both inclusive, taking
           the value WILL_NEVER if no OLSRv2 specific
           information is received from this neighbor."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 5 }

    olsrv2NibNeighborSetNWillRouting  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..15)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is the neighbor's willingness to be
           selected as a routing MPR, in the range from
           WILL_NEVER to WILL_ALWAYS, both inclusive, taking
           the value WILL_NEVER if no OLSRv2 specific
           information is received from this neighbor."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 6 }

    olsrv2NibNeighborSetNFloodingMpr  OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is a boolean flag, describing if
           this neighbor is selected as a flooding MPR
           by this router."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.



Herberg, et al.         Expires October 10, 2013               [Page 37]

Internet-Draft               The OLSRv2-MIB                   April 2013


           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 7 }

    olsrv2NibNeighborSetNRoutingMpr  OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is a boolean flag, describing if
           this neighbor is selected as a routing MPR
           by this router."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 8 }

    olsrv2NibNeighborSetNMprSelector  OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is a boolean flag,
           describing if this neighbor has selected this router
           as a routing MPR, i.e., is a routing MPR
           selector of this router.

           When set to 'true', then this router is selected as
           a routing MPR by the neighbor router.
           When set to 'false',
           then this router is not selected by the neighbor
           as a routing MPR."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 9 }

    olsrv2NibNeighborSetNAdvertised  OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object, N_mpr_selector, is a boolean flag, describing if
           this router has elected to advertise a link to this neighbor
           in its TC messages."
        REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol



Herberg, et al.         Expires October 10, 2013               [Page 38]

Internet-Draft               The OLSRv2-MIB                   April 2013


           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 10 }


    olsrv2NibNeighborSetTableAnsn OBJECT-TYPE
       SYNTAX      Unsigned32 (0..65535)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "Advertised Neighbor Sequence Number (ANSN), is
           a variable, whose value is included in TC messages to
           indicate the freshness of the information transmitted."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 6 }


    --
    -- Topology Information Base - this Information
    -- Base is specific to OLSRv2, and is defined in
    -- Section 10 of RFC XXXX.
    --

    --
    -- Advertising Remote Router Set
    --

    olsrv2TibAdRemoteRouterSetTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2TibAdRemoteRouterSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A router's Advertising Remote Router Set records
           information describing each remote router in the
           network that transmits TC messages."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 7 }

    olsrv2TibAdRemoteRouterSetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2TibAdRemoteRouterSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current



Herberg, et al.         Expires October 10, 2013               [Page 39]

Internet-Draft               The OLSRv2-MIB                   April 2013


       DESCRIPTION
          "A router's Advertised Neighbor Set Table entry
           consists of Advertising Remote Router Tuples:

           (AR_orig_addr, AR_seq_number, AR_time)

           Addresses associated with this router are
           found in the NHDP-MIB module's nhdpDiscIfSetTable."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       INDEX { olsrv2TibAdRemoteRouterSetRouterId }
    ::= { olsrv2TibAdRemoteRouterSetTable 1 }

    Olsrv2TibAdRemoteRouterSetEntry ::=
       SEQUENCE {
          olsrv2TibAdRemoteRouterSetIpAddrType
             InetAddressType,
          olsrv2TibAdRemoteRouterSetIpAddr
             InetAddress,
          olsrv2TibAdRemoteRouterSetRouterId
             NeighborRouterIndex,
          olsrv2TibAdRemoteRouterSetMaxSeqNo
             Unsigned32,
          olsrv2TibAdRemoteRouterSetExpireTime
             TimeStamp
       }

    olsrv2TibAdRemoteRouterSetIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibAdRemoteRouterSetIpAddr,
           as defined in the InetAddress MIB module (RFC4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAdRemoteRouterSetEntry 1 }

    olsrv2TibAdRemoteRouterSetIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only



Herberg, et al.         Expires October 10, 2013               [Page 40]

Internet-Draft               The OLSRv2-MIB                   April 2013


       STATUS      current
       DESCRIPTION
          "This is the originator address of a received
           TC message."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAdRemoteRouterSetEntry 2 }

    olsrv2TibAdRemoteRouterSetRouterId  OBJECT-TYPE
       SYNTAX      NeighborRouterIndex
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "This object is an additional index for each
           Remote Router's IfAddr associated with the
           olsrv2TibAdRemoteRouterSetIpAddr."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAdRemoteRouterSetEntry 3 }

    olsrv2TibAdRemoteRouterSetMaxSeqNo  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..65535)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the greatest ANSN in any TC message
           received which originated from the router
           with originator address
           olsrv2TibAdRemoteRouterSetIpAddr."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAdRemoteRouterSetEntry 4 }

    olsrv2TibAdRemoteRouterSetExpireTime  OBJECT-TYPE
       SYNTAX      TimeStamp
       UNITS       "milliseconds"
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "olsrv2TibAdRemoteRouterSetExpireTime specifies the value
           of sysUptime when this entry should expire and be
           removed from the olsrv2TibAdRemoteRouterSetTable."



Herberg, et al.         Expires October 10, 2013               [Page 41]

Internet-Draft               The OLSRv2-MIB                   April 2013


       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAdRemoteRouterSetEntry 5 }



    --
    -- Router Topology Set
    --

    olsrv2TibRouterTopologySetTable OBJECT-TYPE
       SYNTAX       SEQUENCE OF Olsrv2TibTopologySetEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
          "A router's Router Topology Set records topology
           information about the network."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 8 }

    olsrv2TibRouterTopologySetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2TibTopologySetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "It consists of Router Topology Tuples:

           (TR_from_orig_addr, TR_to_orig_addr,
            TR_seq_number, TR_metric, TR_time)"
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       INDEX { olsrv2TibRouterTopologySetIndex }
    ::= { olsrv2TibRouterTopologySetTable 1 }

    Olsrv2TibTopologySetEntry ::=
       SEQUENCE {
          olsrv2TibRouterTopologySetIndex
             Integer32,
          olsrv2TibRouterTopologySetFromOrigIpAddrType
             InetAddressType,
          olsrv2TibRouterTopologySetFromOrigIpAddr



Herberg, et al.         Expires October 10, 2013               [Page 42]

Internet-Draft               The OLSRv2-MIB                   April 2013


             InetAddress,
          olsrv2TibRouterTopologySetToOrigIpAddrType
             InetAddressType,
          olsrv2TibRouterTopologySetToOrigIpAddr
             InetAddress,
          olsrv2TibRouterTopologySetSeqNo
             Unsigned32,
          olsrv2TibRouterTopologySetMetric
             Float32TC,
          olsrv2TibRouterTopologySetExpireTime
             TimeStamp
       }

    olsrv2TibRouterTopologySetIndex  OBJECT-TYPE
       SYNTAX      Integer32 (0..16777215)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The index for this table."
    ::= { olsrv2TibRouterTopologySetEntry 1 }

    olsrv2TibRouterTopologySetFromOrigIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibRouterTopologySetFromOrigIpAddr,
           as defined in the InetAddress MIB module (RFC4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRouterTopologySetEntry 2 }

    olsrv2TibRouterTopologySetFromOrigIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the originator address of a router which can
           reach the router with originator address TR_to_orig_addr
           in one hop."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.



Herberg, et al.         Expires October 10, 2013               [Page 43]

Internet-Draft               The OLSRv2-MIB                   April 2013


           and U. Herberg, March 2013."
    ::= { olsrv2TibRouterTopologySetEntry 3 }

    olsrv2TibRouterTopologySetToOrigIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibRouterTopologySetToOrigIpAddr,
           as defined in the InetAddress MIB module (RFC4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRouterTopologySetEntry 4 }

    olsrv2TibRouterTopologySetToOrigIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the originator address of a router which can be
           reached by the router with originator address
           TR_to_orig_addr in one hop."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRouterTopologySetEntry 5 }

    olsrv2TibRouterTopologySetSeqNo  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..65535)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the greatest ANSN in any TC message
           received which originated from the router
           with originator address TR_from_orig_addr
           (i.e., which contributed to the information
           contained in this Tuple)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRouterTopologySetEntry 6 }



Herberg, et al.         Expires October 10, 2013               [Page 44]

Internet-Draft               The OLSRv2-MIB                   April 2013


    olsrv2TibRouterTopologySetMetric  OBJECT-TYPE
       SYNTAX      Float32TC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the neighbor metric from the router
           with originator address TR_from_orig_addr to
           the router with originator address
           TR_to_orig_addr."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRouterTopologySetEntry 7 }

    olsrv2TibRouterTopologySetExpireTime  OBJECT-TYPE
       SYNTAX      TimeStamp
       UNITS       "milliseconds"
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "olsrv2TibRouterTopologySetExpireTime specifies the value
           of sysUptime when this entry should expire and be
           removed from the olsrv2TibRouterTopologySetTable."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRouterTopologySetEntry 8 }


    --
    -- Routable Address Topology Set
    --

    olsrv2TibRoutableAddressTopologySetTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2TibRoutableAddressTopologySetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A router's Routable Address Topology Set records topology
           information about the routable addresses within the MANET,
           and via which routers they may be reached."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 9 }



Herberg, et al.         Expires October 10, 2013               [Page 45]

Internet-Draft               The OLSRv2-MIB                   April 2013


    olsrv2TibRoutableAddressTopologySetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2TibRoutableAddressTopologySetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "It consists of Router Topology Tuples:

           (TA_from_orig_addr, TA_dest_addr,
            TA_seq_number, TA_metric, TA_time)"
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       INDEX { olsrv2TibRoutableAddressTopologySetIndex }
    ::= { olsrv2TibRoutableAddressTopologySetTable 1 }

     Olsrv2TibRoutableAddressTopologySetEntry ::=
        SEQUENCE {
           olsrv2TibRoutableAddressTopologySetIndex
             Integer32,
           olsrv2TibRoutableAddressTopologySetFromOrigIpAddrType
             InetAddressType,
           olsrv2TibRoutableAddressTopologySetFromOrigIpAddr
             InetAddress,
           olsrv2TibRoutableAddressTopologySetDestIpAddrType
             InetAddressType,
           olsrv2TibRoutableAddressTopologySetDestIpAddr
             InetAddress,
           olsrv2TibRoutableAddressTopologySetSeqNo
             Unsigned32,
           olsrv2TibRoutableAddressTopologySetMetric
             Float32TC,
           olsrv2TibRoutableAddressTopologySetExpireTime
             TimeStamp
        }

    olsrv2TibRoutableAddressTopologySetIndex  OBJECT-TYPE
       SYNTAX      Integer32 (0..16777215)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The index for this table."
    ::= { olsrv2TibRoutableAddressTopologySetEntry 1 }

    olsrv2TibRoutableAddressTopologySetFromOrigIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType
       MAX-ACCESS  read-only
       STATUS      current



Herberg, et al.         Expires October 10, 2013               [Page 46]

Internet-Draft               The OLSRv2-MIB                   April 2013


       DESCRIPTION
          "The type of the
           olsrv2TibRoutableAddressTopologySetFromOrigIpAddr,
           as defined in the InetAddress MIB module (RFC 4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutableAddressTopologySetEntry 2 }

    olsrv2TibRoutableAddressTopologySetFromOrigIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the originator address of a router which can
           reach the router with routable address TA_dest_addr
           in one hop."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutableAddressTopologySetEntry 3 }

    olsrv2TibRoutableAddressTopologySetDestIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibRouterTopologySetToOrigIpAddr,
           as defined in the InetAddress MIB module (RFC 4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutableAddressTopologySetEntry 4 }

    olsrv2TibRoutableAddressTopologySetDestIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION



Herberg, et al.         Expires October 10, 2013               [Page 47]

Internet-Draft               The OLSRv2-MIB                   April 2013


          "This is a routable address of a router which can be
           reached by the router with originator address
           TA_from_orig_addr in one hop."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutableAddressTopologySetEntry 5 }

    olsrv2TibRoutableAddressTopologySetSeqNo  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..65535)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the greatest ANSN in any TC message
           received which originated from the router
           with originator address TA_from_orig_addr
           (i.e., which contributed to the information
           contained in this Tuple)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutableAddressTopologySetEntry 6 }

    olsrv2TibRoutableAddressTopologySetMetric  OBJECT-TYPE
       SYNTAX      Float32TC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the neighbor metric from the router
           with originator address TA_from_orig_addr to the
           router with OLSRv2 interface address TA_dest_addr."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutableAddressTopologySetEntry 7 }

    olsrv2TibRoutableAddressTopologySetExpireTime  OBJECT-TYPE
       SYNTAX      TimeStamp
       UNITS       "milliseconds"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "olsrv2TibRoutableAddressTopologySetExpireTime
           specifies the value of sysUptime when this entry
           should expire and be removed from the



Herberg, et al.         Expires October 10, 2013               [Page 48]

Internet-Draft               The OLSRv2-MIB                   April 2013


           olsrv2TibRoutableAddressTopologySetTable."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutableAddressTopologySetEntry 8 }


    --
    -- Attached Network Set
    --

    olsrv2TibAttNetworksSetTable OBJECT-TYPE
       SYNTAX       SEQUENCE OF Olsrv2TibAttNetworksSetEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
          "A router's Attached Network Set records information
           about networks (which may be outside the MANET)
           attached to other routers and their routable addresses."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 10 }

    olsrv2TibAttNetworksSetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2TibAttNetworksSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "It consists of Attached Network Tuples:

           (AN_orig_addr, AN_net_addr, AN_seq_number,
            AN_dist, AN_metric, AN_time)"
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       INDEX { olsrv2TibAttNetworksSetIndex }
    ::= { olsrv2TibAttNetworksSetTable 1 }

    Olsrv2TibAttNetworksSetEntry ::=
       SEQUENCE {
          olsrv2TibAttNetworksSetIndex
             Integer32,
          olsrv2TibAttNetworksSetOrigIpAddrType
             InetAddressType,



Herberg, et al.         Expires October 10, 2013               [Page 49]

Internet-Draft               The OLSRv2-MIB                   April 2013


          olsrv2TibAttNetworksSetOrigIpAddr
             InetAddress,
          olsrv2TibAttNetworksSetNetIpAddrType
             InetAddressType,
          olsrv2TibAttNetworksSetNetIpAddr
             InetAddress,
          olsrv2TibAttNetworksSetNetIpAddrPrefixLen
             InetAddressPrefixLength,
          olsrv2TibAttNetworksSetSeqNo
             Unsigned32,
          olsrv2TibAttNetworksSetDist
             Unsigned32,
          olsrv2TibAttNetworksSetMetric
             Float32TC,
          olsrv2TibAttNetworksSetExpireTime
             TimeStamp
       }

    olsrv2TibAttNetworksSetIndex  OBJECT-TYPE
       SYNTAX      Integer32 (0..16777215)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The index for this table."
    ::= { olsrv2TibAttNetworksSetEntry 1 }

    olsrv2TibAttNetworksSetOrigIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibAttNetworksSetOrigIpAddr,
           as defined in the InetAddress MIB module (RFC4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 2 }


    olsrv2TibAttNetworksSetOrigIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION



Herberg, et al.         Expires October 10, 2013               [Page 50]

Internet-Draft               The OLSRv2-MIB                   April 2013


          "This is the originator address of a
           router which can act as gateway to the
           network with address AN_net_addr."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 3 }

    olsrv2TibAttNetworksSetNetIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibAttNetworksSetNetIpAddr,
           as defined in the InetAddress MIB module (RFC 4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 4 }

    olsrv2TibAttNetworksSetNetIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is is the network address of an
           attached network, which may be reached via
           the router with originator address AN_orig_addr."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 5 }

    olsrv2TibAttNetworksSetNetIpAddrPrefixLen  OBJECT-TYPE
       SYNTAX      InetAddressPrefixLength
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "Indicates the number of leading one bits that form the
           mask to be logically ANDed with the destination address
           before being compared to the value in the
           olsrv2TibAttNetworksSetNetIpAddr field."



Herberg, et al.         Expires October 10, 2013               [Page 51]

Internet-Draft               The OLSRv2-MIB                   April 2013


       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 6 }

    olsrv2TibAttNetworksSetSeqNo  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..65535)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The greatest ANSN in any TC
           message received which originated from the
           router with originator address AN_orig_addr
           (i.e., which contributed to the information
           contained in this Tuple)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 7 }

    olsrv2TibAttNetworksSetDist  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..255)
       UNITS       "hops"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The number of hops to the network
           with address AN_net_addr from the router with
           originator address AN_orig_addr."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 8 }

    olsrv2TibAttNetworksSetMetric  OBJECT-TYPE
       SYNTAX      Float32TC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The metric of the link from the router with
           originator address AN_orig_addr to the attached
           network with address AN_net_addr."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.



Herberg, et al.         Expires October 10, 2013               [Page 52]

Internet-Draft               The OLSRv2-MIB                   April 2013


           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 9 }

    olsrv2TibAttNetworksSetExpireTime  OBJECT-TYPE
       SYNTAX      TimeStamp
       UNITS       "milliseconds"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "olsrv2TibAttNetworksSetExpireTime
           specifies the value of sysUptime when this
           entry should expire and be removed from the
           olsrv2TibAttNetworksSetTable."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 10 }



    --
    -- Routing Set
    --

    olsrv2TibRoutingSetTable OBJECT-TYPE
       SYNTAX       SEQUENCE OF Olsrv2TibRoutingSetEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
          "A router's Routing Set records the first hop along a
           selected path to each destination for which any such
           path is known."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 11 }

    olsrv2TibRoutingSetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2TibRoutingSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "It consists of Routing Tuples:

            (R_dest_addr, R_next_iface_addr,
             R_local_iface_addr, R_dist, R_metric)"



Herberg, et al.         Expires October 10, 2013               [Page 53]

Internet-Draft               The OLSRv2-MIB                   April 2013


       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       INDEX { olsrv2TibRoutingSetDestIpAddrType,
               olsrv2TibRoutingSetDestIpAddr,
               olsrv2TibRoutingSetDestIpAddrPrefLen }
    ::= { olsrv2TibRoutingSetTable 1 }

    Olsrv2TibRoutingSetEntry ::=
       SEQUENCE {
          olsrv2TibRoutingSetDestIpAddrType
             InetAddressType,
          olsrv2TibRoutingSetDestIpAddr
             InetAddress,
          olsrv2TibRoutingSetDestIpAddrPrefLen
             InetAddressPrefixLength,
          olsrv2TibRoutingSetNextIfIpAddrType
             InetAddressType,
          olsrv2TibRoutingSetNextIfIpAddr
             InetAddress,
          olsrv2TibRoutingSetLocalIfIpAddrType
             InetAddressType,
          olsrv2TibRoutingSetLocalIfIpAddr
             InetAddress,
          olsrv2TibRoutingSetDist
             Unsigned32,
          olsrv2TibRoutingSetMetric
             Float32TC
       }

    olsrv2TibRoutingSetDestIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibRoutingSetDestIpAddr
           and olsrv2TibRoutingSetNextIfIpAddr,
           as defined in the InetAddress MIB module (RFC 4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 1 }




Herberg, et al.         Expires October 10, 2013               [Page 54]

Internet-Draft               The OLSRv2-MIB                   April 2013


    olsrv2TibRoutingSetDestIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "This is the address of the destination,
           either the address of an interface of
           a destination router, or the network
           address of an attached network."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 2 }

    olsrv2TibRoutingSetDestIpAddrPrefLen  OBJECT-TYPE
       SYNTAX      InetAddressPrefixLength
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "Indicates the number of leading one bits that form the
           mask to be logically ANDed with the destination address
           before being compared to the value in the
           olsrv2TibRoutingSetDestIpAddr field.

           Note: This definition needs to be consistent
           with the current forwarding table MIB module description.
           Specifically, it should allow for longest prefix
           matching of network addresses."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 3 }

    olsrv2TibRoutingSetNextIfIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibRoutingSetNextIfIpAddr
           and olsrv2TibRoutingSetNextIfIpAddr,
           as defined in the InetAddress MIB module (RFC 4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol



Herberg, et al.         Expires October 10, 2013               [Page 55]

Internet-Draft               The OLSRv2-MIB                   April 2013


           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 4 }

    olsrv2TibRoutingSetNextIfIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is the OLSRv2 interface address of the
           next hop on the selected path to the
           destination."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 5 }

    olsrv2TibRoutingSetLocalIfIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibRoutingSetLocalIfIpAddr
           and olsrv2TibRoutingSetNextIfIpAddr,
           as defined in the InetAddress MIB module (RFC 4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 6 }


    olsrv2TibRoutingSetLocalIfIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is the address of the local OLSRv2
           interface over which a packet must be
           sent to reach the destination by the
           selected path."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.



Herberg, et al.         Expires October 10, 2013               [Page 56]

Internet-Draft               The OLSRv2-MIB                   April 2013


           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 7 }

    olsrv2TibRoutingSetDist  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..255)
       UNITS       "hops"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is the number of hops on the selected
           path to the destination."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 8 }

    olsrv2TibRoutingSetMetric  OBJECT-TYPE
       SYNTAX      Float32TC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is the metric of the route
           to the destination with address R_dest_addr."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 9 }




 --
 -- OLSRv2 Performance Group
 --

 --
 --    Contains objects which help to characterize the
 --    performance of the OLSRv2 routing process.
 --

 olsrv2PerformanceObjGrp  OBJECT IDENTIFIER ::= {olsrv2MIBObjects 3}

     --
     -- Objects per local interface
     --




Herberg, et al.         Expires October 10, 2013               [Page 57]

Internet-Draft               The OLSRv2-MIB                   April 2013


    olsrv2InterfacePerfTable  OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2InterfacePerfEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "This table summarizes performance objects that are
           measured per each active local OLSRv2 interface.
           If the olsrv2InterfaceAdminStatus of the interface
           changes to 'disabled' then the row associated with this
           interface should be removed from this table."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2PerformanceObjGrp 1 }

    olsrv2InterfacePerfEntry OBJECT-TYPE
       SYNTAX      Olsrv2InterfacePerfEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A single entry contains performance counters for
           each active local OLSRv2 interface."
       AUGMENTS { nhdpInterfacePerfEntry }
    ::= { olsrv2InterfacePerfTable 1 }

    Olsrv2InterfacePerfEntry ::=
       SEQUENCE {
          olsrv2IfTcMessageXmits
             Counter32,
          olsrv2IfTcMessageRecvd
             Counter32,
          olsrv2IfTcMessageXmitAccumulatedSize
             Counter64,
          olsrv2IfTcMessageRecvdAccumulatedSize
             Counter64,
          olsrv2IfTcMessageTriggeredXmits
             Counter32,
          olsrv2IfTcMessagePeriodicXmits
             Counter32,
          olsrv2IfTcMessageForwardedXmits
             Counter32,
          olsrv2IfTcMessageXmitAccumulatedMPRSelectorCount
             Counter32
       }

    olsrv2IfTcMessageXmits  OBJECT-TYPE
       SYNTAX      Counter32



Herberg, et al.         Expires October 10, 2013               [Page 58]

Internet-Draft               The OLSRv2-MIB                   April 2013


       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "A counter is incremented each time a TC
           message has been transmitted on that interface."
    ::= { olsrv2InterfacePerfEntry 1 }

    olsrv2IfTcMessageRecvd  OBJECT-TYPE
       SYNTAX      Counter32
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "A counter is incremented each time a
           TC message has been received on that interface."
    ::= { olsrv2InterfacePerfEntry 2 }

    olsrv2IfTcMessageXmitAccumulatedSize  OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "A counter is incremented by the number of octets in
           a TC message each time a
           TC message has been sent."
    ::= { olsrv2InterfacePerfEntry 3 }

    olsrv2IfTcMessageRecvdAccumulatedSize  OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "A counter is incremented by the number of octets in
           a TC message each time a
           TC message has been received."
    ::= { olsrv2InterfacePerfEntry 4 }

    olsrv2IfTcMessageTriggeredXmits  OBJECT-TYPE
       SYNTAX      Counter32
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "A counter is incremented each time a triggered
           TC message has been sent."
    ::= { olsrv2InterfacePerfEntry 5 }

    olsrv2IfTcMessagePeriodicXmits  OBJECT-TYPE
       SYNTAX      Counter32
       MAX-ACCESS  read-only



Herberg, et al.         Expires October 10, 2013               [Page 59]

Internet-Draft               The OLSRv2-MIB                   April 2013


       STATUS      current
       DESCRIPTION
          "A counter is incremented each time a periodic
           TC message has been sent."
    ::= { olsrv2InterfacePerfEntry 6 }

    olsrv2IfTcMessageForwardedXmits  OBJECT-TYPE
       SYNTAX      Counter32
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "A counter is incremented each time a
           TC message has been forwarded."
    ::= { olsrv2InterfacePerfEntry 7 }

    olsrv2IfTcMessageXmitAccumulatedMPRSelectorCount OBJECT-TYPE
       SYNTAX      Counter32
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "A counter is incremented by the number of advertised
           MPR selectors in a TC each time a TC
           message has been sent."
    ::= { olsrv2InterfacePerfEntry 8 }



    --
    -- Objects concerning the Routing set
    --

    olsrv2RoutingSetRecalculationCount  OBJECT-TYPE
       SYNTAX      Counter32
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This counter increments each time the Routing Set has
           been recalculated."
    ::= { olsrv2PerformanceObjGrp 2 }

    --
    -- Objects concerning the MPR set
    --

    olsrv2MPRSetRecalculationCount  OBJECT-TYPE
       SYNTAX      Counter32
       MAX-ACCESS  read-only
       STATUS      current



Herberg, et al.         Expires October 10, 2013               [Page 60]

Internet-Draft               The OLSRv2-MIB                   April 2013


       DESCRIPTION
          "This counter increments each time the MPRs
           of this router have been recalculated for
           any of its interfaces."
    ::= { olsrv2PerformanceObjGrp 3 }





 --
 -- Notifications
 --

 olsrv2NotificationsObjects OBJECT IDENTIFIER ::=
                                      { olsrv2MIBNotifications 0 }
 olsrv2NotificationsControl OBJECT IDENTIFIER ::=
                                      { olsrv2MIBNotifications 1 }
 olsrv2NotificationsStates  OBJECT IDENTIFIER ::=
                                      { olsrv2MIBNotifications 2 }


    -- olsrv2NotificationsObjects

    olsrv2RouterStatusChange NOTIFICATION-TYPE
        OBJECTS { olsrv2OrigIpAddrType, -- The address type of
                                        --    the originator of
                                        --    the notification.
                  olsrv2OrigIpAddr,     -- The originator of
                                        --    the notification.
                  olsrv2AdminStatus     -- The new state.
        }
        STATUS      current
        DESCRIPTION
           "olsrv2RouterStatusChange is a notification sent
            when the OLSRv2 router changes it status.
            The router status is maintained in the
            olsrv2AdminStatus object."
    ::= { olsrv2NotificationsObjects 1 }

    olsrv2OrigIpAddrChange NOTIFICATION-TYPE
       OBJECTS { olsrv2OrigIpAddrType, -- The address type of
                                       --    the originator of
                                       --    the notification.
                 olsrv2OrigIpAddr,     -- The originator of
                                       --    the notification.
                 olsrv2PreviousOrigIpAddrType, -- The address
                                       -- type of previous



Herberg, et al.         Expires October 10, 2013               [Page 61]

Internet-Draft               The OLSRv2-MIB                   April 2013


                                       -- address of
                                       -- the originator of
                                       -- the notification.
                 olsrv2PreviousOrigIpAddr  -- The previous
                                       -- address of the
                                       -- originator of
                                       -- the notification.
       }
       STATUS      current
       DESCRIPTION
          "olsrv2OrigIpAddrChange is a notification sent when
           the OLSRv2 router changes it originator IP address.
           The notification includes the new and the previous
           originator IP address of the OLSRv2 router."
    ::= { olsrv2NotificationsObjects 2 }

    olsrv2RoutingSetRecalculationCountChange NOTIFICATION-TYPE
       OBJECTS { olsrv2OrigIpAddrType, -- The address type of
                                       --   the originator of
                                       --   the notification.
                 olsrv2OrigIpAddr,     -- The originator of
                                       --   the notification.
                 olsrv2RoutingSetRecalculationCount  -- The
                                           -- new count of the
                                           -- routing set
                                           -- recalculations.
       }
       STATUS       current
       DESCRIPTION
          "olsrv2RoutingSetRecalculationCountChange is
           a notification sent when a significant number of
           routing set recalculations have occurred.
           The network administrator should select
           appropriate values for 'significant number of
           neighbors' and 'short time' through the settings
           of the olsrv2RoutingSetRecalculationCountThreshold
           and olsrv2RoutingSetRecalculationCountWindow
           objects."
    ::= { olsrv2NotificationsObjects 3 }

    olsrv2MPRSetRecalculationCountChange NOTIFICATION-TYPE
       OBJECTS { olsrv2OrigIpAddrType, -- The address type of
                                       --   the originator of
                                       --   the notification.
                 olsrv2OrigIpAddr,     -- The originator of
                                       --   the notification.
                 olsrv2MPRSetRecalculationCount  -- The new
                                       --   MPR set



Herberg, et al.         Expires October 10, 2013               [Page 62]

Internet-Draft               The OLSRv2-MIB                   April 2013


                                       --   recalculation
                                       --   count.
       }
       STATUS       current
       DESCRIPTION
          "olsrv2MPRSetRecalculationCountChange is
           a notification sent when a significant number of
           MPR set recalculations have occurred.
           The network administrator should select
           appropriate values for 'significant number of
           neighbors' and 'short time' through the settings
           of the olsrv2MPRSetRecalculationCountThreshold
           and olsrv2MPRSetRecalculationCountWindow
           objects."
    ::= { olsrv2NotificationsObjects 4 }


    -- olsrv2NotificationsControl

    olsrv2RoutingSetRecalculationCountThreshold OBJECT-TYPE
       SYNTAX      Integer32 (0..255)
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "A threshold value for the
           olsrv2RoutingSetRecalculationCount object.
           If the number of occurrences exceeds this
           threshold within the previous
           olsrv2RoutingSetReculculationCountWindow,
           then the olsrv2RoutingSetRecalculationCountChange
           notification is to be sent.

           It is recommended that the value of this
           threshold be set to at least 20 and higher
           in dense topologies with frequent expected
           topology changes."
    ::= { olsrv2NotificationsControl 1 }

    olsrv2RoutingSetRecalculationCountWindow OBJECT-TYPE
       SYNTAX      TimeTicks
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "A time window for the
           olsrv2RoutingSetRecalculationCount object.
           If the number of occurrences exceeds the
           olsrv2RoutingSetRecalculationCountThreshold
           within the previous



Herberg, et al.         Expires October 10, 2013               [Page 63]

Internet-Draft               The OLSRv2-MIB                   April 2013


           olsrv2RoutingSetRecalculationCountWindow,
           then the
           olsrv2RoutingSetRecalculationCountChange
           notification is to be sent.

           This object represents the time in hundredths
           of a second.

           It is recommended that the value for this
           window be set to at least 5 times the
           nhdpHelloInterval."
    ::= { olsrv2NotificationsControl 2 }

    olsrv2MPRSetRecalculationCountThreshold OBJECT-TYPE
       SYNTAX      Integer32 (0..255)
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "A threshold value for the
           olsrv2MPRSetRecalculationCount object.
           If the number of occurrences exceeds this
           threshold within the previous
           olsrv2MPRSetReculculationCountWindow,
           then the
           olsrv2MPRSetRecalculationCountChange
           notification is to be sent.

           It is recommended that the value of this
           threshold be set to at least 20 and higher
           in dense topologies with frequent expected
           topology changes."
    ::= { olsrv2NotificationsControl 3 }

    olsrv2MPRSetRecalculationCountWindow OBJECT-TYPE
       SYNTAX       TimeTicks
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
          "A time window for the
           olsrv2MPRSetRecalculationCount object.
           If the number of occurrences exceeds the
           olsrv2MPRSetRecalculationCountThreshold
           within the previous
           olsrv2MPRSetRecalculationCountWindow,
           then the
           olsrv2MPRSetRecalculationCountChange
           notification is to be sent.
           This object represents the time in hundredths



Herberg, et al.         Expires October 10, 2013               [Page 64]

Internet-Draft               The OLSRv2-MIB                   April 2013


           of a second.

           It is recommended that the value for this
           window be set to at least 5 times the
           nhdpHelloInterval."
    ::= { olsrv2NotificationsControl 4 }


    -- olsrv2NotificationStates

    olsrv2PreviousOrigIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2PreviousOrigIpAddr,
           as defined in the InetAddress MIB module (RFC 4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NotificationsStates 1 }

    olsrv2PreviousOrigIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The previous origination IP address
           of this OLSRv2 router.

           This object should be updated each time
           the olsrv2OrigIpAddr is modified.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NotificationsStates 2 }






Herberg, et al.         Expires October 10, 2013               [Page 65]

Internet-Draft               The OLSRv2-MIB                   April 2013


    --
    -- Compliance Statements
    --

    olsrv2Compliances  OBJECT IDENTIFIER ::= { olsrv2MIBConformance 1 }
    olsrv2MIBGroups    OBJECT IDENTIFIER ::= { olsrv2MIBConformance 2 }

    olsrv2BasicCompliance  MODULE-COMPLIANCE
       STATUS current
       DESCRIPTION
          "The basic implementation requirements for
           managed network entities that implement
           the OLSRv2 routing process."
       MODULE  -- this module
       MANDATORY-GROUPS { olsrv2ConfigObjectsGroup }
    ::= { olsrv2Compliances 1 }

    olsrv2FullCompliance MODULE-COMPLIANCE
       STATUS current
       DESCRIPTION
          "The full implementation requirements for
           managed network entities that implement
           the OLSRv2 routing process."
       MODULE  -- this module
       MANDATORY-GROUPS { olsrv2ConfigObjectsGroup,
                          olsrv2StateObjectsGroup,
                          olsrv2PerfObjectsGroup,
                          olsrv2NotificationsObjectsGroup,
                          olsrv2NotificationsGroup }
    ::= { olsrv2Compliances 2 }

    --
    -- Units of Conformance
    --

    olsrv2ConfigObjectsGroup OBJECT-GROUP
       OBJECTS {
          olsrv2AdminStatus,
          olsrv2InterfaceAdminStatus,
          olsrv2OrigIpAddrType,
          olsrv2OrigIpAddr,
          olsrv2OHoldTime,
          olsrv2TcInterval,
          olsrv2TcMinInterval,
          olsrv2THoldTime,
          olsrv2AHoldTime,
          olsrv2RxHoldTime,
          olsrv2PHoldTime,



Herberg, et al.         Expires October 10, 2013               [Page 66]

Internet-Draft               The OLSRv2-MIB                   April 2013


          olsrv2FHoldTime,
          olsrv2TpMaxJitter,
          olsrv2TtMaxJitter,
          olsrv2FMaxJitter,
          olsrv2TcHopLimit,
          olsrv2WillFlooding,
          olsrv2WillRouting,
          olsrv2LinkMetricType
       }
       STATUS      current
       DESCRIPTION
          "Set of OLSRv2 configuration objects implemented
           in this module."
    ::= { olsrv2MIBGroups 1 }

    olsrv2StateObjectsGroup  OBJECT-GROUP
       OBJECTS {
          olsrv2LibOrigSetIpAddrType,
          olsrv2LibOrigSetIpAddr,
          olsrv2LibOrigSetExpireTime,
          olsrv2LibLocAttNetSetIpAddrType,
          olsrv2LibLocAttNetSetIpAddr,
          olsrv2LibLocAttNetSetIpAddrPrefixLen,
          olsrv2LibLocAttNetSetDistance,
          olsrv2LibLocAttNetSetMetric,
          olsrv2IibLinkSetInMetric,
          olsrv2IibLinkSetOutMetric,
          olsrv2IibLinkSetMprSelector,
          olsrv2Iib2HopSetInMetric,
          olsrv2Iib2HopSetOutMetric,
          olsrv2NibNeighborSetNOrigIpAddrType,
          olsrv2NibNeighborSetNOrigIpAddr,
          olsrv2NibNeighborSetNInMetric,
          olsrv2NibNeighborSetNOutMetric,
          olsrv2NibNeighborSetNWillFlooding,
          olsrv2NibNeighborSetNWillRouting,
          olsrv2NibNeighborSetNFloodingMpr,
          olsrv2NibNeighborSetNRoutingMpr,
          olsrv2NibNeighborSetNMprSelector,
          olsrv2NibNeighborSetNAdvertised,
          olsrv2NibNeighborSetTableAnsn,
          olsrv2TibAdRemoteRouterSetIpAddrType,
          olsrv2TibAdRemoteRouterSetIpAddr,
          olsrv2TibAdRemoteRouterSetMaxSeqNo,
          olsrv2TibRouterTopologySetFromOrigIpAddrType,
          olsrv2TibRouterTopologySetFromOrigIpAddr,
          olsrv2TibRouterTopologySetToOrigIpAddrType,
          olsrv2TibRouterTopologySetToOrigIpAddr,



Herberg, et al.         Expires October 10, 2013               [Page 67]

Internet-Draft               The OLSRv2-MIB                   April 2013


          olsrv2TibRouterTopologySetSeqNo,
          olsrv2TibRouterTopologySetMetric,
          olsrv2TibRoutableAddressTopologySetExpireTime,
          olsrv2TibRoutableAddressTopologySetFromOrigIpAddrType,
          olsrv2TibRoutableAddressTopologySetFromOrigIpAddr,
          olsrv2TibRoutableAddressTopologySetDestIpAddrType,
          olsrv2TibRoutableAddressTopologySetDestIpAddr,
          olsrv2TibRoutableAddressTopologySetSeqNo,
          olsrv2TibRoutableAddressTopologySetMetric,
          olsrv2TibAttNetworksSetOrigIpAddrType,
          olsrv2TibAttNetworksSetOrigIpAddr,
          olsrv2TibAttNetworksSetNetIpAddrType,
          olsrv2TibAttNetworksSetNetIpAddr,
          olsrv2TibAttNetworksSetNetIpAddrPrefixLen,
          olsrv2TibAttNetworksSetSeqNo,
          olsrv2TibAttNetworksSetDist,
          olsrv2TibAttNetworksSetMetric,
          olsrv2TibAttNetworksSetExpireTime,
          olsrv2TibRoutingSetNextIfIpAddrType,
          olsrv2TibRoutingSetNextIfIpAddr,
          olsrv2TibRoutingSetLocalIfIpAddrType,
          olsrv2TibRoutingSetLocalIfIpAddr,
          olsrv2TibRoutingSetDist,
          olsrv2TibRoutingSetMetric
       }
       STATUS      current
       DESCRIPTION
          "Set of OLSRv2 state objects implemented
           in this module."
    ::= { olsrv2MIBGroups 2 }

    olsrv2PerfObjectsGroup  OBJECT-GROUP
       OBJECTS {
          olsrv2IfTcMessageXmits,
          olsrv2IfTcMessageRecvd,
          olsrv2IfTcMessageXmitAccumulatedSize,
          olsrv2IfTcMessageRecvdAccumulatedSize,
          olsrv2IfTcMessageTriggeredXmits,
          olsrv2IfTcMessagePeriodicXmits,
          olsrv2IfTcMessageForwardedXmits,
          olsrv2IfTcMessageXmitAccumulatedMPRSelectorCount,
          olsrv2RoutingSetRecalculationCount,
          olsrv2MPRSetRecalculationCount
       }
       STATUS      current
       DESCRIPTION
          "Set of OLSRv2 performance objects implemented
           in this module by total and per interface."



Herberg, et al.         Expires October 10, 2013               [Page 68]

Internet-Draft               The OLSRv2-MIB                   April 2013


    ::= { olsrv2MIBGroups 3 }

    olsrv2NotificationsObjectsGroup OBJECT-GROUP
       OBJECTS {
          olsrv2RoutingSetRecalculationCountThreshold,
          olsrv2RoutingSetRecalculationCountWindow,
          olsrv2MPRSetRecalculationCountThreshold,
          olsrv2MPRSetRecalculationCountWindow,
          olsrv2PreviousOrigIpAddrType,
          olsrv2PreviousOrigIpAddr
       }
       STATUS      current
       DESCRIPTION
          "Set of OLSRv2 notification objects implemented
           in this module."
    ::= { olsrv2MIBGroups 4 }


    olsrv2NotificationsGroup NOTIFICATION-GROUP
       NOTIFICATIONS {
          olsrv2RouterStatusChange,
          olsrv2OrigIpAddrChange,
          olsrv2RoutingSetRecalculationCountChange,
          olsrv2MPRSetRecalculationCountChange
       }
       STATUS current
       DESCRIPTION
           "Set of OLSRv2 notifications implemented
            in this module."
    ::= { olsrv2MIBGroups 5 }

 END


8.  Security Considerations

   This MIB module defines objects for the configuration, monitoring and
   notification of the Optimized Link State Routing protocol version 2
   [OLSRv2].  OLSRv2 allows routers to acquire topological information
   of the routing domain by virtue of exchanging TC message, to
   calculate shortest paths to each destination router in the routing
   domain, to select relays for network-wide transmissions etc.

   There are a number of management objects defined in this MIB module
   with a MAX-ACCESS clause of read-write and/or read-create.  Such
   objects may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on



Herberg, et al.         Expires October 10, 2013               [Page 69]

Internet-Draft               The OLSRv2-MIB                   April 2013


   network operations.  These are the tables and objects and their
   sensitivity/vulnerability:

   o  olsrv2TcInterval, olsrv2TcMinInterval - these writable objects
      control the rate at which TC messages are sent.  If set at too
      high a rate, this could represent a form of DOS attack by
      overloading interface resources.  If set low, OLSRv2 may not
      converge fast enough to provide accurate routes to all
      destinations in the routing domain.

   o  olsrv2TcHopLimit - defines the hop limit for TC messages.  If set
      too low, messages will not be forwarded beyond the defined scope,
      and thus routers further away from the message originator will not
      be able to construct appropriate topology graphs.

   o  olsrv2OHoldTime, olsrv2THoldTime, olsrv2AHoldTime,
      olsrv2RxHoldTime, olsrv2PHoldTime, olsrv2FHoldTime - define hold
      times for tuples of different Information Bases of OLSRv2.  If set
      too low, information will expire quickly, and may this harm a
      correct operation of the routing protocol.

   o  olsrv2WillFlooding and olsrv2WillRouting - define the willingness
      of this router to become MPR.  If this is set to WILL_NEVER (0),
      the managed router will not forward any TC messages, nor accept a
      selection to become MPR by neighboring routers.  If set to
      WILL_ALWAYS (15), the router will be preferred by neighbors during
      MPR selection, and may thus attract more traffic.

   o  olsrv2TpMaxJitter, olsrv2TtMaxJitter, olsrv2FMaxJitter - define
      jitter values for TC message transmission and forwarding.  If set
      too low, control traffic may get lost if the channel is lossy.

   o  olsrv2LinkMetricType - defines the type of the link metric that a
      router uses (e.g., ETX or hop-count).  Whenever this value
      changes, all link metric information recorded by the router is
      invalid, causing a reset of information acquired from other
      routers in the MANET.  Moreover, if olsrv2LinkMetricType on a
      router is set to a value that is not known to other routers in the
      MANET, these routers will not be able to establish routes to that
      router or transiting that router.  Existing routes to the router
      with a olsrv2LinkMetricType unknown to other routers in the MANET
      will be removed.

   Some of the readable objects in this MIB module (i.e., objects with a
   MAX-ACCESS other than not-accessible) may be considered sensitive or
   vulnerable in some network environments.  It is thus important to
   control even GET and/or NOTIFY access to these objects and possibly
   to even encrypt the values of these objects when sending them over



Herberg, et al.         Expires October 10, 2013               [Page 70]

Internet-Draft               The OLSRv2-MIB                   April 2013


   the network via SNMP.  These are the tables and objects and their
   sensitivity/vulnerability:

   o  olsrv2TibRouterTopologySetTable - The contains information on the
      topology of the MANET, specifically the IP address of the routers
      in the MANET (as identified by
      olsrv2TibRouterTopologySetFromOrigIpAddr and
      olsrv2TibRouterTopologySetToOrigIpAddr objects).  This information
      provides an adversary broad information on the members of the
      MANET, located within this single table.  This information can be
      use to expedite attacks on the other members of the MANET without
      having to go through a laborious discovery process on their own.
      olsrv2TibRouterTopologySetFromOrigIpAddr is the index into the
      table, and has a MAX-ACCESS of 'not-accessible'.  However, this
      information can be exposed using SNMP operations.

   MANET technology is often deployed to support communications of
   emergency services or military tactical applications.  In these
   applications, it is imperative to maintain the proper operation of
   the communications network and to protect sensitive information
   related to its operation.  Therefore, when implementing these
   capabilities, the full use of SNMPv3 cryptographic mechanisms for
   authentication and privacy is RECOMMENDED.

   SNMP versions prior to SNMPv3 did not include adequate security.
   Even if the network itself is secure (for example by using IPSec),
   there is no control as to who on the secure network is allowed to
   access and GET/SET (read/change/create/delete) the objects in this
   MIB module.

   It is RECOMMENDED that implementers consider the security features as
   provided by the SNMPv3 framework (see [RFC3410], Section 8, including
   full support for the SNMPv3 cryptographic mechanisms (for
   authentication and privacy).

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED.  Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module is properly configured to give access to
   the objects only to those principals (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.

9.  Applicability Statement

   This document describes objects for configuring parameters of the
   Optimized Link State Routing version 2 (OLSRv2) Protocol [OLSRv2]
   process on a router.  This MIB module, denoted OLSRv2-MIB, also



Herberg, et al.         Expires October 10, 2013               [Page 71]

Internet-Draft               The OLSRv2-MIB                   April 2013


   reports state, performance information and notifications.  The OLSRv2
   protocol relies upon information gathered via the Neighborhood
   Discovery Protocol [RFC6130] in order to perform its operations.  The
   NHDP protocol is managed via the NHDP-MIB [RFC6779].

   MANET deployments can greatly differ in aspects of dynamicity of the
   topology, capacity and loss rates of underlying channels, traffic
   flow directions, memory and CPU capacity of routers etc.  SNMP and
   therefore this MIB module are only applicable for a subset of MANET
   deployments, in particular deployments:

   o  In which routers have enough memory and CPU resources to run SNMP
      and expose the MIB module.

   o  Where a network management station (NMS) is defined to which
      notifications are sent, and from which routers can be managed.

   o  Where this NMS is reachable from routers in the MANET most of the
      time (as notifications to the NMS and management information from
      the NMS to the router will be lost when connectivity is
      temporarily lost).  This requires that the topology of the MANET
      is only moderately dynamic.

   o  Where the underlying wireless channel supports enough bandwidth to
      run SNMP, and where loss rates of the channel are not exhaustive.

   Certain MANET deployments, such as community networks with non-mobile
   routers, dynamic topology because of changing link quality, and a
   pre-defined gateway (that could also serve as NMS), are examples of
   networks applicable for this MIB module.  Other, more constrained
   deployments of MANETs may not be able to run SNMP and require
   different management protocols.

   Some level of configuration, i.e., read-write objects, are desirable
   for OLSRv2 deployments.  Topology related configuration such as the
   ability to enable OLSRv2 on new interfaces or initially configure
   OLSRv2 on a router's interfaces through the
   olsrv2InterfaceAdminStatus object is critical to initial system
   startup.  The OLSRv2 protocol allows for some level of performance
   tuning through various protocol parameters and this MIB allows for
   configuration of those protocol parameters through read-write objects
   such as the olsrv2TcHopLimit or the olsrv2FMaxJitter.  Other read-
   write objects allow for the control of Notification behavior through
   this MIB module, e.g., the
   olsrv2RoutingSetRecalculationCountThreshold object.  A fuller
   discussion of MANET network management applicability is to be
   provided elsewhere [USE-CASES].




Herberg, et al.         Expires October 10, 2013               [Page 72]

Internet-Draft               The OLSRv2-MIB                   April 2013


   OLSRv2 is designed to allow routers to leverage information on
   discovered routers and generate unicast routing paths within the
   MANET.

10.  IANA Considerations

   The MIB module in this document uses the following IANA-assigned
   OBJECT IDENTIFIER value recorded in the SMI Numbers registry:

         Descriptor        OBJECT IDENTIFIER value
         ----------        -----------------------
         OLSRv2-MIB          { mib-2 ZZZZ }
         IANA EDITOR NOTE: please assign ZZZZ

11.  Acknowledgements

   The authors would like thank Adrian Farrel, as well as the entire
   MANET WG for reviews of this document.

   This MIB document uses the template authored by D. Harrington which
   is based on contributions from the MIB Doctors, especially Juergen
   Schoenwaelder, Dave Perkins, C.M.Heard and Randy Presuhn.

12.  References

12.1.  Normative References

   [RFC2863]     McCloghrie, K. and F. Kastenholz, "The Interfaces Group
                 MIB", RFC 2863, June 2000.

   [RFC3418]     Presuhn, R., "Management Information Base (MIB) for the
                 Simple Network Management Protocol (SNMP)", STD 62,
                 RFC 3418, December 2002.

   [RFC2119]     Bradner, S., "Key words for use in RFCs to Indicate
                 Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2578]     McCloghrie, K., Ed., Perkins, D., Ed., and J.
                 Schoenwaelder, Ed., "Structure of Management
                 Information Version 2 (SMIv2)", STD 58, RFC 2578,
                 April 1999.

   [RFC2579]     McCloghrie, K., Ed., Perkins, D., Ed., and J.
                 Schoenwaelder, Ed., "Textual Conventions for SMIv2",
                 STD 58, RFC 2579, April 1999.

   [RFC2580]     McCloghrie, K., Perkins, D., and J. Schoenwaelder,
                 "Conformance Statements for SMIv2", STD 58, RFC 2580,



Herberg, et al.         Expires October 10, 2013               [Page 73]

Internet-Draft               The OLSRv2-MIB                   April 2013


                 April 1999.

   [OLSRv2]      Clausen, T., Dearlove, C., Jacquet, P., and U. Herberg,
                 "The Optimized Link State Routing Protocol version 2",
                 draft-ietf-manet-olsrv2-19 (work in progress),
                 March 2013.

   [RFC6130]     Clausen, T., Dearlove, C., and J. Dean, "Mobile Ad Hoc
                 Network (MANET) Neighborhood Discovery Protocol
                 (NHDP)", RFC 6130, April 2011.

   [RFC6340]     Presuhn, R., "Textual Conventions for the
                 Representation of Floating-Point Numbers", RFC 6340,
                 August 2011.

   [RFC6779]     Herberg, U., Cole, R., and I. Chakeres, "Definition of
                 Managed Objects for the Neighborhood Discovery
                 Protocol", RFC 6779, May 2012.

   [RFC4001]     Daniele, M., Haberman, B., Routhier, S., and J.
                 Schoenwaelder, "Textual Conventions for Internet
                 Network Addresses", RFC 4001, February 2005.

12.2.  Informative References

   [RFC3410]     Case, J., Mundy, R., Partain, D., and B. Stewart,
                 "Introduction and Applicability Statements for
                 Internet-Standard Management Framework", RFC 3410,
                 December 2002.

   [REPORT-MIB]  Cole, R., Macker, J., and A. Bierman, "Definition of
                 Managed Objects for Performance Reporting",
                 draft-ietf-manet-report-mib-03 (work in progress),
                 November 2012.

   [USE-CASES]   Nguyen, J., Cole, R., Herberg, U., Yi, J., and J. Dean,
                 "Network Management of Mobile Ad hoc Networks (MANET):
                 Architecture, Use Cases, and Applicability",
                 draft-nguyen-manet-management-00 (work in progress),
                 February 2013.











Herberg, et al.         Expires October 10, 2013               [Page 74]

Internet-Draft               The OLSRv2-MIB                   April 2013


Appendix A.  Note to the RFC Editor


   ***************************************************************
   * Note to the RFC Editor (to be removed prior to publication) *
   *                                                             *
   * 1) The reference to RFCYYYY within the DESCRIPTION clauses  *
   * of the MIB module point to this draft and are to be         *
   * assigned by the RFC Editor.                                 *
   *                                                             *
   * 2) The reference to RFCXXXX throughout this document point  *
   * to the current draft-ietf-manet-olsrv2-xx.txt.  This        *
   * needs to be replaced with the XXXX RFC number for the       *
   * OLSRv2 publication.                                         *
   *                                                             *
   ***************************************************************

Authors' Addresses

   Ulrich Herberg
   Fujitsu Laboratories of America
   1240 East Arques Avenue
   Sunnyvale, CA  94085
   USA

   EMail: ulrich@herberg.name
   URI:   http://www.herberg.name/


   Robert G. Cole
   US Army CERDEC
   6010 Frankford Road, Bldg 6010
   Aberdeen Proving Ground, Maryland  21005
   USA

   Phone: +1 443 395 8744
   EMail: robert.g.cole@us.army.mil
   URI:   http://www.cs.jhu.edu/~rgcole/













Herberg, et al.         Expires October 10, 2013               [Page 75]

Internet-Draft               The OLSRv2-MIB                   April 2013


   Thomas Heide Clausen
   LIX, Ecole Polytechnique
   Palaiseau Cedex,   91128
   France

   Phone: +33 6 6058 9349
   EMail: T.Clausen@computer.org
   URI:   http://www.ThomasClausen.org/











































Herberg, et al.         Expires October 10, 2013               [Page 76]


Html markup produced by rfcmarkup 1.109, available from https://tools.ietf.org/tools/rfcmarkup/