[Docs] [txt|pdf|xml|html] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: (draft-cole-manet-olsrv2-mib) 00 01 02 03 04 05 06 07 08 09 10 11 12 RFC 7184

Internet Engineering Task Force                               U. Herberg
Internet-Draft                           Fujitsu Laboratories of America
Intended status: Standards Track                                 R. Cole
Expires: December 14, 2013                                US Army CERDEC
                                                              T. Clausen
                                                LIX, Ecole Polytechnique
                                                           June 12, 2013


  Definition of Managed Objects for the  Optimized Link State Routing
                           Protocol version 2
                     draft-ietf-manet-olsrv2-mib-11

Abstract

   This document defines the Management Information Base (MIB) module
   for configuring and managing the Optimized Link State Routing
   protocol version 2 (OLSRv2).  The OLSRv2-MIB module is structured
   into configuration information, state information, performance
   information, and notifications.  This additional state and
   performance information is useful to troubleshoot problems and
   performance issues of the routing protocol.  Two levels of compliance
   allow this MIB module to be deployed on constrained routers.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on December 14, 2013.

Copyright Notice

   Copyright (c) 2013 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents



Herberg, et al.         Expires December 14, 2013               [Page 1]

Internet-Draft               The OLSRv2-MIB                    June 2013


   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
   2.  The Internet-Standard Management Framework . . . . . . . . . .  3
   3.  Conventions  . . . . . . . . . . . . . . . . . . . . . . . . .  3
   4.  Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .  3
     4.1.  Terms  . . . . . . . . . . . . . . . . . . . . . . . . . .  4
   5.  Structure of the MIB Module  . . . . . . . . . . . . . . . . .  4
     5.1.  The Configuration Group  . . . . . . . . . . . . . . . . .  5
     5.2.  The State Group  . . . . . . . . . . . . . . . . . . . . .  5
     5.3.  The Performance Group  . . . . . . . . . . . . . . . . . .  5
     5.4.  The Notifications Group  . . . . . . . . . . . . . . . . .  6
     5.5.  Tables and Indexing  . . . . . . . . . . . . . . . . . . .  6
   6.  Relationship to Other MIB Modules  . . . . . . . . . . . . . .  9
     6.1.  Relationship to the SNMPv2-MIB . . . . . . . . . . . . . .  9
     6.2.  Relationship to the NHDP-MIB . . . . . . . . . . . . . . .  9
     6.3.  MIB modules required for IMPORTS . . . . . . . . . . . . .  9
   7.  Definitions  . . . . . . . . . . . . . . . . . . . . . . . . . 10
   8.  Security Considerations  . . . . . . . . . . . . . . . . . . . 76
   9.  Applicability Statement  . . . . . . . . . . . . . . . . . . . 79
   10. IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 80
   11. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 80
   12. References . . . . . . . . . . . . . . . . . . . . . . . . . . 80
     12.1. Normative References . . . . . . . . . . . . . . . . . . . 80
     12.2. Informative References . . . . . . . . . . . . . . . . . . 82
   Appendix A.  Appendix A: . . . . . . . . . . . . . . . . . . . . . 82
   Appendix B.  Note to the RFC Editor  . . . . . . . . . . . . . . . 84
















Herberg, et al.         Expires December 14, 2013               [Page 2]

Internet-Draft               The OLSRv2-MIB                    June 2013


1.  Introduction

   This document defines the Management Information Base (MIB) module
   for configuring and managing the Optimized Link State Routing
   protocol version 2 (OLSRv2).  The OLSRv2-MIB module is structured
   into configuration information, state information, performance
   information, and notifications.  In addition to configuration, this
   additional state and performance information is useful to
   troubleshoot problems and performance issues of the routing protocol.
   Different levels of compliance allow implementers to use smaller
   subsets of all defined objects, allowing for this MIB module to be
   deployed on more constrained routers.

2.  The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to Section 7 of
   [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB module are defined using the mechanisms defined in
   the Structure of Management Information (SMI).  This document
   specifies a MIB module that is compliant to the SMIv2, which is
   described in [RFC2578], [RFC2579], and [RFC2580].

3.  Conventions

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   [RFC2119].

4.  Overview

   The Optimized Link State Routing Protocol version 2 (OLSRv2) [OLSRv2]
   is a table driven, proactive routing protocol, i.e., it exchanges
   topology information with other routers in the network periodically.
   OLSRv2 is an optimization of the classical link state routing
   protocol.  Its key concept is that of MultiPoint Relays (MPRs).  Each
   router selects a set of its neighbor routers (which "cover" all of
   its symmetrically connected 2-hop neighbor routers) as MPRs.  MPRs
   are then used to achieve both flooding reduction and topology
   reduction.

   This document provides management and control capabilities of an
   OLSRv2 instance, allowing management applications to monitor the



Herberg, et al.         Expires December 14, 2013               [Page 3]

Internet-Draft               The OLSRv2-MIB                    June 2013


   state and performance of an OLSRV2 router, as well as to change
   settings of the OLSRv2 instance (e.g., router or interface parameters
   such as message intervals etc.).

   As OLSRv2 relies on the neighborhood information discovered by the
   "Mobile Ad Hoc Network (MANET) Neighborhood Discovery Protocol
   (NHDP)" [RFC6130], the OLSRv2-MIB module is aligned with the NHDP-MIB
   [RFC6779] module and augments several of the tables and objects in
   the NHDP-MIB.  In particular, common indexes for router interfaces
   and discovered neighbors are used, as described in Section 5.2.

4.1.  Terms

   The following definitions apply throughout this document:

   o  Configuration Objects - switches, tables, objects which are
      initialized to default settings or set through the management
      interface defined by this MIB module.

   o  State Objects - automatically generated values which define the
      current operating state of the OLSRv2 protocol instance in the
      router.

   o  Performance Objects - automatically generated values which help an
      administrator or automated tool to assess the performance of the
      OLSRv2 routing process on the router.

   o  Notification Objects - define triggers and associated notification
      messages allowing for asynchronous tracking of pre-defined events
      on the managed router.

5.  Structure of the MIB Module

   This section presents the structure of the OLSRv2-MIB module.  The
   objects are arranged into the following structure:

   o  olsrv2MIBObjects - defines objects forming the basis for the
      OLSRv2-MIB module.  These objects are divided up by function into
      the following groups:

      *  Configuration Group - defining objects related to the
         configuration of the OLSRv2 instance on the router.

      *  State Group - defining objects which reflect the current state
         of the OLSRv2 instance running on the router.

      *  Performance Group -defining objects which are useful to a
         management station when characterizing the performance of



Herberg, et al.         Expires December 14, 2013               [Page 4]

Internet-Draft               The OLSRv2-MIB                    June 2013


         OLSRv2 on the router and in the MANET.

   o  olsrv2MIBNotifications - objects defining OLSRv2-MIB module
      notifications.

   o  olsrv2MIBConformance - defining the minimal and maximal
      conformance requirements for implementations of this MIB module.

5.1.  The Configuration Group

   The OLSRv2 router is configured with a set of controls.  The
   authoritative list of configuration controls within the OLSRv2-MIB
   module is found within the MIB module itself.  Generally, an attempt
   was made in developing the OLSRv2-MIB module to support all
   configuration objects defined in [OLSRv2].  For all of the
   configuration parameters, the same constraints and default values of
   these parameters as defined in [OLSRv2] are followed.

5.2.  The State Group

   The State Group reports current state information of a router running
   [OLSRv2].  The OLSRv2-MIB module State Group tables were designed to
   contain the complete set of state information defined within the
   information bases in [OLSRv2].

   The OLSRv2-MIB module State Group tables are constructed as
   extensions to the corresponding tables within the State Group of the
   NHDP-MIB [RFC6779] module.  Use of the AUGMENTS clause is made, when
   possible, to accomplish these table extensions.  Further, the State
   Group tables defined in this MIB module are aligned with the
   according tables in the NHDP-MIB [RFC6779] module, as described in
   Section 6.2.

5.3.  The Performance Group

   The Performance Group reports values relevant to system performance.
   Frequent changes of sets or frequent recalculation of the routing set
   or the MPRs can have a negative influence on the performance of
   OLSRv2.  This MIB module defines several objects that can be polled
   in order to, e.g., calculate histories or monitor frequencies of
   changes.  This may help the network administrator to determine
   unusual topology changes or other changes that affect stability and
   reliability of the MANET.  One such framework is specified in REPORT-
   MIB [REPORT-MIB].







Herberg, et al.         Expires December 14, 2013               [Page 5]

Internet-Draft               The OLSRv2-MIB                    June 2013


5.4.  The Notifications Group

   The Notifications Group contains Control
   (olsrv2NotificationsControl), Objects (olsrv2NotificationsObjects)
   and States (olsrv2NotificationsStates), where the Control contains
   definitions of objects to control the frequency of notifications
   being generated.  The Objects define the supported notifications and
   the State is used to define additional information to be carried
   within the notifications.

   The olsrv2NotificationsObjects sub-tree contains the list of
   notifications supported within the OLSRv2-MIB module and their
   intended purpose or utility.

   The same mechanisms for improving the network performance by reducing
   the number of notifications apply as defined in Section 5.1 of
   [RFC6779].  The following objects are used to define the thresholds
   and time windows for specific notifications defined in the NHDP-MIB
   module: olsrv2RoutingSetRecalculationCountThreshold,
   olsrv2RoutingSetRecalculationCountWindow,
   olsrv2MPRSetRecalculationCountThreshold, and
   olsrv2MPRSetRecalculationCountWindow.

5.5.  Tables and Indexing

   The OLSRv2-MIB module's tables are indexed by the following
   constructs:

   o  nhdpIfIndex - the ifIndex of the local router on which NHDP is
      configured.  This is defined in the NHDP-MIB.

   o  nhdpDiscIfIndex - a locally managed index representing a known
      interface on a neighboring router.  This is defined in the NHDP-
      MIB.

   o  nhdpDiscRouterIndex - a locally managed index representing an ID
      of a known neighboring router.  This is defined in the NHDP-MIB.

   o  {olsrv2LibOrigSetIpAddrType, olsrv2LibOrigSetIpAddr} - this index
      (pair) uniquely identifies recently used originator addresses
      found within the olsrv2LibOrigSetTable.

   o  {olsrv2LibLocAttNetSetIpAddrType, olsrv2LibLocAttNetSetIpAddr,
      olsrv2LibLocAttNetSetIpAddrPerfixLen} - this index (triplet)
      uniquely identifies local attached networks reachable through
      local (non-OLSRv2) interfaces on this router.  These are recorded
      in the olsrv2LibLocAttNetSetTable.




Herberg, et al.         Expires December 14, 2013               [Page 6]

Internet-Draft               The OLSRv2-MIB                    June 2013


   o  {olsrv2TibAdRemoteRouterSetIpAddrType,
      olsrv2TibAdRemoteRouterSetIpAddr} - this index (pair) uniquely
      identifies each router in the network that transmits TC messages
      received by this router.  These records are recorded in the
      olsrv2TibAdRemoteRouterSetIpAddr.

   o  {olsrv2TibRouterTopologySetFromOrigIpAddrType,
      olsrv2TibRouterTopologySetFromOrigIpAddr,
      olsrv2TibRouterTopologySetToOrigIpAddrType,
      olsrv2TibRouterTopologySetToOrigIpAddr} - this index (quadruplet)
      uniquely identifies discovered links within the network recorded
      by this router.  Information associated with each link is stored
      in the olsrv2TibRouterTopologySetTable.

   o  {olsrv2TibRoutableAddressTopologySetFromOrigIpAddrType,
      olsrv2TibRoutableAddressTopologySetFromOrigIpAddr,
      olsrv2TibRoutableAddressTopologySetFromDestIpAddrType,
      olsrv2TibRoutableAddressTopologySetFromDestIpAddr} - this index
      (quadruplet) uniquely identifies reachable addresses within the
      network and the router's advertising these addresses.  This
      information is stored in the
      olsrv2TibRoutableAddressTopologySetTable.

   o  {olsrv2TibAttNetworksSetOrigIpAddrType,
      olsrv2TibAttNetworksSetOrigIpAddr,
      olsrv2TibAttNetworksSetNetIpAddrType,
      olsrv2TibAttNetworksSetNetIpAddr,
      olsrv2TibAttNetworksSetNetIpAddrPrefixLen} - this index
      (quintuplet) uniquely identifies the networks (which may be
      outside the MANET) and the routers through which these networks
      can be reached.  This information is stored in the
      olsrv2TibAttNetworksSetTable.

   o  {olsrv2TibRoutingSetDestIpAddrType, olsrv2TibRoutingSetDestIpAddr,
      olsrv2TibRoutingSetDestIpAddrPrefixLen} - this index (triplet)
      uniquely identifies the address of a reachable destination in the
      network.  This indexes the olsrv2TibRoutingSetTable which contains
      the next hop information to reach the indexed addresses.

   These tables and their indexing are:

   o  olsrv2InterfaceTable - describes the OLSRv2 status on the NHDP
      interfaces of this router.  This table augments nhdpInterfaceEntry
      and as such it is indexed by the {nhdpIfIndex} from the NHDP-MIB.

   o  olsrv2IibLinkSetTable - records all links from other routers which
      are, or recently were, 1-hop neighbors.  This table augments
      nhdpIibLinkSetEntry and as such it is indexed by nhdpIfIndex and



Herberg, et al.         Expires December 14, 2013               [Page 7]

Internet-Draft               The OLSRv2-MIB                    June 2013


      nhdpDiscIfIndex.

   o  olsrv2Iib2HopSetTable - records network addresses of symmetric
      2-hop neighbors and the links to the associated 1-hop neighbors.
      This table augments nhdpIib2HopSetEntry and as such it is indexed
      by {nhdpIfIndex, nhdpDiscIfIndex, nhdpIib2HopSetIpAddressType,
      nhdpIib2HopSetIpAddress}.

   o  olsrv2LibOrigSetTable - records addresses that were recently used
      as originator addresses by this router.  This table is indexed by
      {olsrv2LibOrigSetIpAddrType, olsrv2LibOrigSetIpAddr}.

   o  olsrv2LibLocAttNetSetTable - records its local non-OLSRv2
      interfaces via which it can act as gateways to other networks.
      This table is indexed by {olsrv2LibLocAttNetSetIpAddrType,
      olsrv2LibLocAttNetSetIpAddr,
      olsrv2LibLocAttNetSetIpAddrPerfixLen}.

   o  olsrv2NibNeighborSetTable - records all network addresses of each
      1-hop neighbor.  This table augments nhdpNibNeighborSetEntry and
      as such it is indexed by the {nhdpDiscRouterIndex}.

   o  olsrv2TibAdRemoteRouterSetTable - records information describing
      each remote router in the network that transmits TC messages.
      This table is indexed by {olsrv2TibAdRemoteRouterSetIpAddrType,
      olsrv2TibAdRemoteRouterSetIpAddr}.

   o  olsrv2TibRouterTopologySetTable - records topology information
      about the network.  This table is indexed by
      {olsrv2TibRouterTopologySetFromOrigIpAddrType,
      olsrv2TibRouterTopologySetFromOrigIpAddr,
      olsrv2TibRouterTopologySetToOrigIpAddrType,
      olsrv2TibRouterTopologySetToOrigIpAddr}.

   o  olsrv2TibRoutableAddressTopologySetTable - records topology
      information about the routable addresses within the MANET, and via
      which routers they may be reached.  This table is indexed by
      {olsrv2TibRoutableAddressTopologySetFromOrigIpAddrType,
      olsrv2TibRoutableAddressTopologySetFromOrigIpAddr,
      olsrv2TibRoutableAddressTopologySetFromDestIpAddrType,
      olsrv2TibRoutableAddressTopologySetFromDestIpAddr}.

   o  olsrv2TibAttNetworksSetTable - records information about networks
      (which may be outside the MANET) attached to other routers and
      their routable addresses.  This table is indexed by
      {olsrv2TibAttNetworksSetOrigIpAddrType,
      olsrv2TibAttNetworksSetOrigIpAddr,
      olsrv2TibAttNetworksSetNetIpAddrType,



Herberg, et al.         Expires December 14, 2013               [Page 8]

Internet-Draft               The OLSRv2-MIB                    June 2013


      olsrv2TibAttNetworksSetNetIpAddr,
      olsrv2TibAttNetworksSetNetIpAddrPrefixLen}.

   o  olsrv2TibRoutingSetTable - records the first hop along a selected
      path to each destination for which any such path is known.  This
      table is indexed by {olsrv2TibRoutingSetDestIpAddrType,
      olsrv2TibRoutingSetDestIpAddr,
      olsrv2TibRoutingSetDestIpAddrPrefixLen}.

   o  olsrv2InterfacePerfTable - records performance counters for each
      active OLSRv2 interface on this device.  This table augments
      nhdpInterfacePerfEntry and as such it is indexed by {nhdpIfIndex}
      from the NHDP-MIB.

6.  Relationship to Other MIB Modules

   This section specifies the relationship of the MIB modules contained
   in this document to other standards, particularly to standards
   containing other MIB modules.  MIB modules and specific definitions
   imported from MIB modules that SHOULD be implemented in conjunction
   with the MIB module contained within this document are identified in
   this section.

6.1.  Relationship to the SNMPv2-MIB

   The System group in the SNMPv2-MIB [RFC3418] module is defined as
   being mandatory for all systems, and the objects apply to the entity
   as a whole.  The System group provides identification of the
   management entity and certain other system-wide data.  The OLSRv2-MIB
   module does not duplicate those objects.

6.2.  Relationship to the NHDP-MIB

   OLSRv2 depends on the neighborhood information that is discovered by
   [RFC6130].  An instance of OLSRv2 MUST have an associated instance of
   NHDP running on the same device for proper operations of the
   discovery and routing system.  In order for the OLSRv2-MIB module to
   correctly populate the objects relating to discovered neighbors, the
   State Group tables of the NHDP-MIB [RFC6779] module are aligned with
   the State Group tables of this MIB module.  This is accomplished
   through the use of the AUGMENTS capability of SMIv2 (where
   appropriate).  This will allow for cross referencing of information
   between the two MIB modules within a given SNMP context.

6.3.  MIB modules required for IMPORTS

   The following OLSRv2-MIB module IMPORTS objects from NHDP-MIB
   [RFC6779], SNMPv2-SMI [RFC2578], SNMPv2-TC [RFC2579], SNMPv2-CONF



Herberg, et al.         Expires December 14, 2013               [Page 9]

Internet-Draft               The OLSRv2-MIB                    June 2013


   [RFC2580], IF-MIB [RFC2863] and INET-ADDRESS-MIB [RFC4001].

7.  Definitions

   This section contains the OLSRv2-MIB module defined by the
   specification.


    OLSRv2-MIB DEFINITIONS ::= BEGIN

    IMPORTS

       MODULE-IDENTITY, OBJECT-TYPE, Counter32, Counter64,
       Integer32, Unsigned32, mib-2, TimeTicks,
       NOTIFICATION-TYPE
                FROM SNMPv2-SMI -- RFC 2578

       TEXTUAL-CONVENTION, TimeStamp, TruthValue
                FROM SNMPv2-TC -- RFC 2579

       MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
                FROM SNMPv2-CONF -- STD 58

       InetAddressType, InetAddress,
       InetAddressPrefixLength
                FROM INET-ADDRESS-MIB -- RFC 3291

       nhdpInterfaceEntry,
       nhdpIibLinkSetEntry, nhdpIib2HopSetEntry,
       nhdpNibNeighborSetEntry, nhdpInterfacePerfEntry
                FROM NHDP-MIB -- RFC 6779

       IANAolsrv2LinkMetricTypeTC
                FROM IANAolsrv2LinkMetricType-MIB
       ;

    manetOlsrv2MIB MODULE-IDENTITY
       LAST-UPDATED "201306120000Z"   --12 June 2013
       ORGANIZATION "IETF MANET Working Group"
       CONTACT-INFO
          "WG E-Mail: manet@ietf.org

           WG Chairs: sratliff@cisco.com
                      jmacker@nrl.navy.mil


           Editors:   Ulrich Herberg
                      Fujitsu Laboratories of America



Herberg, et al.         Expires December 14, 2013              [Page 10]

Internet-Draft               The OLSRv2-MIB                    June 2013


                      1240 East Arques Avenue
                      Sunnyvale, CA 94085
                      USA
                      ulrich@herberg.name
                      http://www.herberg.name/

                      Thomas Heide Clausen
                      Ecole Polytechnique
                      LIX
                      91128 Palaiseau Cedex
                      France
                      http://www.thomasclausen.org/
                      T.Clausen@computer.org

                      Robert G. Cole
                      US Army CERDEC
                      Space and Terrestrial Communications
                      6010 Frankford Street
                      Bldg 6010, Room 453H
                      Aberdeen Proving Ground, MD 21005
                      USA
                      +1 443 395-8744
                      robert.g.cole@us.army.mil
                      http://www.cs.jhu.edu/~rgcole/"

       DESCRIPTION
          "This OLSRv2-MIB module is applicable to routers
           implementing the Optimized Link State Routing Protocol
           version 2 (OLSRv2) defined in RFC XXXX.

           Copyright (c) 2013 IETF Trust and the persons
           identified as authors of the code.  All rights reserved.

           Redistribution and use in source and binary forms, with
           or without modification, is permitted pursuant to, and
           subject to the license terms contained in, the Simplified
           BSD License set forth in Section 4.c of the IETF Trust's
           Legal Provisions Relating to IETF Documents
           (http://trustee.ietf.org/license-info).

           This version of this MIB module is part of RFC YYYY; see
           the RFC itself for full legal notices."

         -- Revision History
         REVISION    "201306120000Z"   -- 12 June 2013
         DESCRIPTION
          "Initial version of this MIB module,
           published as RFC YYYY."



Herberg, et al.         Expires December 14, 2013              [Page 11]

Internet-Draft               The OLSRv2-MIB                    June 2013


         -- RFC-Editor assigns ZZZZ (this comment can be removed)
         ::= { mib-2 ZZZZ }


 --
 -- TEXTUAL CONVENTIONS
 --

 Olsrv2MetricValueCompressedFormTC ::= TEXTUAL-CONVENTION
    DISPLAY-HINT "x"
    STATUS      current
    DESCRIPTION
       "OLSRv2 Metrics are expressed in terms of a Link Metric
        Compressed Form within the OLSRv2 protocol.  This textual
        convention defines the syntax of the metric objects
        consistent with the definitions of the OLSRv2 Link
        Metric Compressed Form in Section 6.2 of RFC XXXX.

        The 12-bit compressed form of a link metric uses a modified
        form of a representation with an 8-bit mantissa (denoted a)
        and a 4-bit exponent (denoted b).  Note that if represented
        as the 12 bit value 256b+a then the ordering of those 12 bit
        values is identical to the ordering of the represented values.

        The value so represented is (257+a)2^b - 256, where ^ denotes
        exponentiation.  This has a minimum value
        (when a = 0 and b = 0) of MINIMUM_METRIC = 1 and a maximum
        value (when a = 255 and b = 15) of MAXIMUM_METRIC = 2^24 - 256.

        Hence the compressed form metric values range from 1 to
        16776960.  The special value of 0 is reserved for the
        UNKNOWN_METRIC value.

        If a network manager sets the metric value 'm' through the
        MIB-module, then the OLSRv2 code can derive 'compressed_m'
        = M(a,b) according to the algorithm in RFC 5497 and
        'compressed_m' is the value represented in the OLSRv2 messages.
        But the value 'm' is persistently stored by the MIB-module.
        If the MIB-module is pulling this time parameter from some other
        source, i.e., the protocol instance, then this value is stored
        as is."
    SYNTAX  Unsigned32 (0..16776960)

 Olsrv2TimeValueCompressedForm32TC ::= TEXTUAL-CONVENTION
    DISPLAY-HINT "x"
    STATUS      current
    DESCRIPTION
       "OLSRv2 time values may be expressed in terms of a compressed



Herberg, et al.         Expires December 14, 2013              [Page 12]

Internet-Draft               The OLSRv2-MIB                    June 2013


        form within the OLSRv2 protocol.  This textual convention
        defines the syntax of the time objects defined in terms of
        an interger number of millisceonds, consistent with the
        definitions of the 8-bit exponent-mantissa compressed form
        defined in Section 5 of RFC 5497.  Time values with this
        representation are defined in terms of a constant C which
        is represented in terms of seconds.  The constant C
        (time granularity) is used as specified in RFC 5497.
        It MUST be the same as is used by the NHDP protocol
        RFC 6130.

        The 8-bit compressed form of a time value uses a modified
        form of a representation with an 3-bit mantissa (denoted a)
        and a 5-bit exponent (denoted b).  Note that if represented
        as the 8 bit value 8b+a then the ordering of those 8 bit
        values is identical to the ordering of the represented values.

        The minimum time-value that can be represented in this manner
        is C.  The maximum time-value that can be represented in
        this manner is 15 * 2^28 * C,  15*268,435,456 * C,
        4,026,531,840 * C or about 45 days if, for example,
        C = 1/1024 second.

        This TEXTUAL-CONVENTION limits the maximum value of the
        time granularity constant C to be no greater than 1/1024
        seconds due to its use of the Unsigned32 syntax limiting
        the maximum number of milliseconds to no more than
        3932160000.

        When OLSRv2 uses this 8-bit exponent-mantissa compressed
        form, this object value MUST be translated from the
        integer form represented in this MIB-module into the
        exponent-mantissa form for the OLSRv2 protocol to use
        according to the algorithm defined in Section 5 of
        RFC 5497 for finding the next larger time value within
        the exponent-mantissa format.

        If a network manager sets the time value 't' through the
        MIB-module, then the OLSRv2 code can derive
        'compressed_t' = T(a,b) according to the algorithm
        in RFC 5497 and 'compressed_t' is the value represented
        in the OLSRv2 messages. But the value 't' is persistently
        stored by the MIB-module. If the MIB-module is pulling
        this time parameter from some other source which is using
        the compressed form, i.e., the protocol instance, then
        this value is stored as is, after converting from
        number of time constants C into number of milliseconds."
    SYNTAX  Unsigned32 (1..3932160000)



Herberg, et al.         Expires December 14, 2013              [Page 13]

Internet-Draft               The OLSRv2-MIB                    June 2013


 Olsrv2StatusTC ::= TEXTUAL-CONVENTION
    STATUS      current
    DESCRIPTION
       "Controls the operation of the OLSRv2
        protocol on the device or a specific interface.
        For example, for an interface: 'enabled' indicates
        that OLSRv2 is permitted to operate,
        and 'disabled' indicates that it is not."
    SYNTAX  INTEGER {
       enabled (1),
       disabled (2)
    }

 WillingnessTC ::= TEXTUAL-CONVENTION
    DISPLAY-HINT "x"
    STATUS    current
    DESCRIPTION
       "A willingness value which evaluates to the
        device's interest in participating in
        a particular function, process or behavior.

        The williness ranges from a low value of
        WILL_NEVER(0) to a high value of
        WILL_ALWAYS(15).  For each parameter x,
        there is an associated willingness value
        W(x) such that WILL_NEVER < W(x) <= WILL_ALWAYS."
    SYNTAX   Unsigned32 (0..15)


 --
 -- Top-Level Object Identifier Assignments
 --

 olsrv2MIBNotifications OBJECT IDENTIFIER ::= { manetOlsrv2MIB 0 }
 olsrv2MIBObjects       OBJECT IDENTIFIER ::= { manetOlsrv2MIB 1 }
 olsrv2MIBConformance   OBJECT IDENTIFIER ::= { manetOlsrv2MIB 2 }

 --
 -- olsrv2ConfigurationGroup
 --

 --    Contains the OLSRv2 objects that configure specific
 --    options that determine the overall performance and operation
 --    of the OLSRv2 routing process.

 olsrv2ConfigurationGroup OBJECT IDENTIFIER ::= {olsrv2MIBObjects 1}





Herberg, et al.         Expires December 14, 2013              [Page 14]

Internet-Draft               The OLSRv2-MIB                    June 2013


    olsrv2AdminStatus  OBJECT-TYPE
       SYNTAX      Olsrv2StatusTC
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "The configured status of the OLSRv2 process
           on this device.  'enabled(1)' means that
           OLSRv2 is configured to run on this device.
           'disabled(2)' mean that the OLSRv2 process
           is configured off.

           Operation of the OLSRv2 routing protocol
           requires the operation of the Neighborhood
           Discovery Protocol (RFC 6130).  Hence, this
           object cannot have a status of 'enabled'
           unless at least one interface on the device
           is a MANET interface with NHDP enabled on that
           interface.  If a network manager attempts to
           set this object to 'enabled' when no interfaces
           on this device have HNDP enabled, the device
           MUST fail the set with inconsistentValue.
           If all device interfaces running NHDP become
           disabled or removed, then the
           olsrv2AdminStatus MUST be 'disabled'.

           If the network manager, or other means, sets
           this object to 'disabled', then the associated
           interface specific objects, i.e., the
           olsrv2InterfaceAdminStatus objects MUST all
           be 'disabled'.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       DEFVAL { 2 }
    ::= { olsrv2ConfigurationGroup 1 }

    olsrv2InterfaceTable  OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2InterfaceEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The olsrv2InterfaceTable describes the OLSRv2
           status on the NHDP interfaces of this router.
           As such, this table augments the nhdpInterfaceTable
           defined in the NHDP-MIB (RFC 6779). NHDP interfaces
           are explicitly defined by network management, CLI,
           or other means for interfaces on the device that are



Herberg, et al.         Expires December 14, 2013              [Page 15]

Internet-Draft               The OLSRv2-MIB                    June 2013


           intended to run MANET protocols.  The
           olsrv2InterfaceTable contains a single object, the
           olsrv2InterfaceAdminStatus object.  This
           object is set either by network management, or by
           other means, e.g., CLI.

           A conceptual row in this table exists if and only
           if a corresponding entry in the nhdpInterfaceTable
           exists. If the corresponding entry with nhdpIfIndex
           value is deleted from the nhdpInterfaceTable, then
           the entry in this table is automatically deleted and
           OLSRv2 is disabled on this interface,
           and all configuration and state information
           related to this interface is to be removed
           from memory.

           The olsrv2InterfaceAdminStatus can only be
           'enabled' if the corresponding olsrv2AdminStatus
           object is also set to 'enabled'."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2ConfigurationGroup 2 }

    olsrv2InterfaceEntry OBJECT-TYPE
       SYNTAX      Olsrv2InterfaceEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The olsrv2InterfaceEntry describes one OLSRv2
           local interface configuration as indexed by
           its nhdpIfIndex as defined in the
           NHDP-MIB (RFC 6779).

           The objects in this table are persistent and when
           written the device SHOULD save the change to
           non-volatile storage.  For further information
           on the storage behavior for these objects, refer
           to the description for the nhdpIfRowStatus
           object in the NHDP-MIB (RFC6779)."
       REFERENCE
          "RFC 6779 - The Neighborhood Discovery Protocol MIB,
           Herberg, U., Cole, R.G. and I. Chakeres,
           October 2012"
       AUGMENTS { nhdpInterfaceEntry }
    ::= { olsrv2InterfaceTable 1 }




Herberg, et al.         Expires December 14, 2013              [Page 16]

Internet-Draft               The OLSRv2-MIB                    June 2013


    Olsrv2InterfaceEntry ::=
       SEQUENCE {
          olsrv2InterfaceAdminStatus
             Olsrv2StatusTC
       }

    olsrv2InterfaceAdminStatus OBJECT-TYPE
       SYNTAX      Olsrv2StatusTC
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
          "The OLSRv2 interface's administrative status.
           The value 'enabled(1)' denotes that the interface
           is permitted to participate in the OLSRv2 routing
           process.  The value 'disabled(2)' denotes that
           the interface is not permitted to participate
           in the OLSRv2 routing process.

           The configuration objects for the OLSRv2 routing
           process, other than the administrative status objects,
           are common to all interfaces on this device.
           As such, the OLSRv2 configuration objects are globally
           defined for the device and are not contained within
           the olsrv2InterfaceTable."
       DEFVAL { 2 }
    ::= { olsrv2InterfaceEntry 1 }

    olsrv2OrigIpAddrType  OBJECT-TYPE
        SYNTAX      InetAddressType { ipv4(1) , ipv6(2) }
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION
           "The type of the olsrv2OrigIpAddr, as defined
            in the InetAddress MIB module (RFC 4001).

            Only the values 'ipv4(1)' and
            'ipv6(2)' are supported."
        REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2ConfigurationGroup 3 }

    olsrv2OrigIpAddr  OBJECT-TYPE
        SYNTAX      InetAddress (SIZE(4|16))
        MAX-ACCESS  read-write
        STATUS      current
        DESCRIPTION



Herberg, et al.         Expires December 14, 2013              [Page 17]

Internet-Draft               The OLSRv2-MIB                    June 2013


           "The router's originator address. An address that
            is unique (within the MANET) to this router.

            This object is persistent and when written
            the entity SHOULD save the change to
            non-volatile storage."
        REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2ConfigurationGroup 4 }

    --
    -- Local History Times
    --

    olsrv2OHoldTime  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2OHoldTime corresponds to
          O_HOLD_TIME of OLSRv2 and represents the
          time for which a recently used and replaced
          originator address is used to recognize the router's
          own messages.

          Guidance for setting this object may be found
          in Section 5 of the OLSRv2 specification (RFC XXXX),
          which indicates that:
              o  olsrv2OHoldTime > 0

          This object is persistent and when written
          the entity SHOULD save the change to
          non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 30000 }
    ::= { olsrv2ConfigurationGroup 5 }


    --
    -- Message intervals
    --



Herberg, et al.         Expires December 14, 2013              [Page 18]

Internet-Draft               The OLSRv2-MIB                    June 2013


    olsrv2TcInterval  OBJECT-TYPE
       SYNTAX      Olsrv2TimeValueCompressedForm32TC
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2TcInterval corresponds to
          TC_INTERVAL of OLSRv2 and represents the
          maximum time between the transmission of
          two successive TC messages by this router.

          Guidance for setting this object may be found
          in Section 5 of the OLSRv2 specification (RFC XXXX),
          which indicates that:

              o olsrv2TcInterval > 0
              o olsrv2TcInterval >= olsrv2TcMinInterval

          This object is persistent and when written
          the entity SHOULD save the change to
          non-volatile storage."
       REFERENCE
          "Section 5 on Representing Time.
           RFC 5497 - Representing Multi-Value Time in
           Mobile Ad Hoc Networks (MANETs),
           Clausen, T. and C. Dearlove, March 2009.

           and

           Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 5000 }
    ::= { olsrv2ConfigurationGroup 6 }

    olsrv2TcMinInterval  OBJECT-TYPE
       SYNTAX      Olsrv2TimeValueCompressedForm32TC
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2TcMinInterval corresponds to
          TC_MIN_INTERVAL of OLSRv2 and represents
          the minimum interval between transmission of
          two successive TC messages by this router.

          Guidance for setting this object may be found



Herberg, et al.         Expires December 14, 2013              [Page 19]

Internet-Draft               The OLSRv2-MIB                    June 2013


          in Section 5 of the OLSRv2 specification (RFC XXXX),
          which indicates that:
              o olsrv2TcInterval >= olsrv2TcMinInterval

          The OLSRv2 protocol may choose to represent this
          time interval in terms of the 8-bit exponent-mantissa
          form defined in Section 5 of RFC 5497.  When this
          is the case, this object value MUST be translated
          from the integer form represented in this
          MIB-module into the exponent-mantissa form for the
          OLSRv2 protocol to use according to the algorithm
          defined in Section 5 of RFC 5497 for finding the
          next larger time value within the exponent-mantissa
          format.

          This object is persistent and when written
          the entity SHOULD save the change to
          non-volatile storage."
       REFERENCE
          "Section 5 on Representing Time.
           RFC 5497 - Representing Multi-Value Time in
           Mobile Ad Hoc Networks (MANETs),
           Clausen, T. and C. Dearlove, March 2009.

           and

           Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 1250 }
    ::= { olsrv2ConfigurationGroup 7 }


    --
    -- Advertised information validity times
    --

    olsrv2THoldTime  OBJECT-TYPE
       SYNTAX      Olsrv2TimeValueCompressedForm32TC
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2THoldTime corresponds to
          T_HOLD_TIME of OLSRv2 and is used as the
          minimum value in the TLV with
          Type = VALIDITY_TIME included in all



Herberg, et al.         Expires December 14, 2013              [Page 20]

Internet-Draft               The OLSRv2-MIB                    June 2013


          TC messages sent by this router.

          Guidance for setting this object may be found
          in Section 5 of the OLSRv2 specification (RFC XXXX),
          which indicates that:
              o olsrv2THoldTime >= olsrv2TcInterval
              o If TC messages can be lost, then
                olsrv2THoldTime SHOULD be
                significantly greater than olsrv2TcInterval;
                a value >= 3 x olsrv2TcInterval is RECOMMENDED.

          This object is persistent and when written
          the entity SHOULD save the change to
          non-volatile storage."
       REFERENCE
          "Section 5 on Representing Time.
           RFC 5497 - Representing Multi-Value Time in
           Mobile Ad Hoc Networks (MANETs),
           Clausen, T. and C. Dearlove, March 2009.

           and

           Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 15000 }
    ::= { olsrv2ConfigurationGroup 8 }

    olsrv2AHoldTime  OBJECT-TYPE
       SYNTAX      Olsrv2TimeValueCompressedForm32TC
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2AHoldTime corresponds to
          A_HOLD_TIME of OLSRv2 and represents
          the period during which TC messages are sent
          after they no longer have any advertised
          information to report, but are sent in order
          to accelerate outdated information removal by other
          routers.

          Guidance for setting this object may be found
          in Section 5 of the OLSRv2 specification (RFC XXXX),
          which indicates that:
             o If TC messages can be lost, then
               olsrv2AHoldTime SHOULD be



Herberg, et al.         Expires December 14, 2013              [Page 21]

Internet-Draft               The OLSRv2-MIB                    June 2013


               significantly greater than olsrv2TcInterval;
               a value >= 3 x olsrv2TcInterval is
               RECOMMENDED.

          This object is persistent and when written
          the entity SHOULD save the change to
          non-volatile storage."
       REFERENCE
          "Section 5 on Representing Time.
           RFC 5497 - Representing Multi-Value Time in
           Mobile Ad Hoc Networks (MANETs),
           Clausen, T. and C. Dearlove, March 2009.

           and

           Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 15000 }
    ::= { olsrv2ConfigurationGroup 9 }

    --
    -- Received message validity times
    --

    olsrv2RxHoldTime  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2RxHoldTime corresponds to
           RX_HOLD_TIME of OLSRv2 and represents the period
           after receipt of a message by the appropriate OLSRv2
           interface of this router for which that information
           is recorded, in order that the message is recognized
           as having been previously received on this OLSRv2
           interface.

           Guidance for setting this object may be found
           in Section 5 of the OLSRv2 specification (RFC XXXX),
           which indicates that:
              o olsrv2RxHoldTime > 0
              o This parameter SHOULD be greater
                than the maximum difference in time that a
                message may take to traverse the MANET,
                taking into account any message forwarding



Herberg, et al.         Expires December 14, 2013              [Page 22]

Internet-Draft               The OLSRv2-MIB                    June 2013


                jitter as well as propagation, queuing,
                and processing delays.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 30000 }
    ::= { olsrv2ConfigurationGroup 10 }

    olsrv2PHoldTime  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2PHoldTime corresponds to
           P_HOLD_TIME of OLSRv2 and represents the period
           after receipt of a message that is processed by
           this router for which that information is recorded,
           in order that the message is not processed again
           if received again.

           Guidance for setting this object may be found
           in Section 5 of the OLSRv2 specification (RFC XXXX),
           which indicates that:
              o olsrv2PHoldTime > 0
              o This parameter SHOULD be greater
                than the maximum difference in time that a
                message may take to traverse the MANET,
                taking into account any message forwarding
                jitter as well as propagation, queuing,
                and processing delays.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 30000 }
    ::= { olsrv2ConfigurationGroup 11 }



Herberg, et al.         Expires December 14, 2013              [Page 23]

Internet-Draft               The OLSRv2-MIB                    June 2013


    olsrv2FHoldTime  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2FHoldTime corresponds to
           F_HOLD_TIME of OLSRv2 and represents the period
           after receipt of a message that is forwarded by this
           router for which that information is recorded, in order
           that the message is not forwarded again if received again.

           Guidance for setting this object may be found
           in Section 5 of the OLSRv2 specification (RFC XXXX),
           which indicates that:
              o olsrv2FHoldTime > 0
              o This parameter SHOULD be greater
                than the maximum difference in time that a
                message may take to traverse the MANET,
                taking into account any message forwarding
                jitter as well as propagation, queuing,
                and processing delays.

           This parameter SHOULD be greater
           than the maximum difference in time that a
           message may take to traverse the MANET,
           taking into account any message forwarding
           jitter as well as propagation, queuing,
           and processing delays.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 30000 }
    ::= { olsrv2ConfigurationGroup 12 }


    --
    -- Jitter times
    --

    olsrv2TpMaxJitter  OBJECT-TYPE
       SYNTAX      Unsigned32



Herberg, et al.         Expires December 14, 2013              [Page 24]

Internet-Draft               The OLSRv2-MIB                    June 2013


       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2TpMaxJitter corresponds to
           TP_MAXJITTER of OLSRv2 and represents the value
           of MAXJITTER used in RFC5148 for periodically
           generated TC messages sent by this router.

           For constraints on these parameters see RFC 5148.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 500 }
    ::= { olsrv2ConfigurationGroup 13 }

    olsrv2TtMaxJitter  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2TtMaxJitter corresponds to
           TT_MAXJITTER of OLSRv2 and represents the value
           of MAXJITTER used in RFC5148 for externally
           triggered TC messages sent by this router.

           For constraints on these parameters see RFC 5148.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 500 }
    ::= { olsrv2ConfigurationGroup 14 }


    olsrv2FMaxJitter  OBJECT-TYPE



Herberg, et al.         Expires December 14, 2013              [Page 25]

Internet-Draft               The OLSRv2-MIB                    June 2013


       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2FMaxJitter corresponds to
           F_MAXJITTER of OLSRv2 and represents the
           default value of MAXJITTER used in RFC 5148 for
           messages forwarded by this router.

           For constraints on these parameters see RFC 5148.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 500 }
    ::= { olsrv2ConfigurationGroup 15 }


    --
    -- Hop limits
    --

    olsrv2TcHopLimit  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..255)
       UNITS       "hops"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2TcHopLimit corresponds to
           TC_HOP_LIMIT of OLSRv2.

           Guidance for setting this object may be found
           in Section 5 of the OLSRv2 specification (RFC XXXX),
           which indicates that:
              o The maximum value of
                olsrv2TcHopLimit >= the network diameter
               in hops, a value of 255 is RECOMMENDED.
              o All values of olsrv2TcHopLimit >= 2.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."



Herberg, et al.         Expires December 14, 2013              [Page 26]

Internet-Draft               The OLSRv2-MIB                    June 2013


        REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
        DEFVAL { 255 }
    ::= { olsrv2ConfigurationGroup 16 }


    --
    -- Willingness
    --

    olsrv2WillRouting  OBJECT-TYPE
       SYNTAX      WillingnessTC
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2WillRouting corresponds to
           WILL_ROUTING of OLSRv2.

           Guidance for setting this object may be found
           in Section 5 of the OLSRv2 specification (RFC XXXX),
           which indicates that:
              o WILL_NEVER (0) <= olsrv2WillRouting <=
                                   WILL_ALWAYS (15)

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 7 }
    ::= { olsrv2ConfigurationGroup 17 }


    olsrv2WillFlooding     OBJECT-TYPE
       SYNTAX      WillingnessTC
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2WillFlooding corresponds to
           WILL_FLOODING of OLSRv2.

           Guidance for setting this object may be found



Herberg, et al.         Expires December 14, 2013              [Page 27]

Internet-Draft               The OLSRv2-MIB                    June 2013


           in Section 5 of the OLSRv2 specification (RFC XXXX),
           which indicates that:
              o WILL_NEVER (0) <= olsrv2WillFlooding <=
                                   WILL_ALWAYS (15)

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { 7 }
    ::= { olsrv2ConfigurationGroup 18 }


    olsrv2LinkMetricType  OBJECT-TYPE
       SYNTAX      IANAolsrv2LinkMetricTypeTC
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "olsrv2LinkMetricType corresponds to
           LINK_METRIC_TYPE of OLSRv2.

           If olsrv2LinkMetricType changes, then all
           link metric information recorded by this router
           is invalid.  The router MUST take the
           actions described in Section 5.5.
           'Parameter Change Constraints' and
           Section 17 'Information Base Changes'
           in RFC XXXX.

           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "Section 5 on Protocol Parameters.
           RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       DEFVAL { unknown }
    ::= { olsrv2ConfigurationGroup 19 }



 --
 -- olsrv2StateGroup



Herberg, et al.         Expires December 14, 2013              [Page 28]

Internet-Draft               The OLSRv2-MIB                    June 2013


 --

 --
 -- Contains information describing the current state of
 -- the OLSRv2 process.
 --

 olsrv2StateGroup  OBJECT IDENTIFIER ::= { olsrv2MIBObjects 2 }

    --
    -- Interface Information Base (IIB)
    --

    --
    -- Link Set from RFC 6130, extended by L_in_metric,
    -- L_out_metric, and L_mpr_selector entries for each tuple
    --

    olsrv2IibLinkSetTable OBJECT-TYPE
       SYNTAX       SEQUENCE OF Olsrv2IibLinkSetEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
          "A Link Set of an interface records all links
           from other routers which are, or recently
           were, 1-hop neighbors."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 1 }

    olsrv2IibLinkSetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2IibLinkSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A Link Set consists of Link Tuples, each
           representing a single link indexed by the
           local and remote interface pair. Each Link Set
           from NHDP is extended by OLSRv2 by the following
           fields:

           (L_in_metric (olsrv2IibLinkSetInMetric),
            L_out_metric (olsrv2IibLinkSetOutMetric),
            L_mpr_selector (olsrv2IibLinkSetMprSelector))"
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol



Herberg, et al.         Expires December 14, 2013              [Page 29]

Internet-Draft               The OLSRv2-MIB                    June 2013


           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       AUGMENTS { nhdpIibLinkSetEntry }
    ::= { olsrv2IibLinkSetTable 1 }

    Olsrv2IibLinkSetEntry ::=
       SEQUENCE {
          olsrv2IibLinkSetInMetric
             Olsrv2MetricValueCompressedFormTC,
          olsrv2IibLinkSetOutMetric
             Olsrv2MetricValueCompressedFormTC,
          olsrv2IibLinkSetMprSelector
             TruthValue
       }

    olsrv2IibLinkSetInMetric  OBJECT-TYPE
       SYNTAX      Olsrv2MetricValueCompressedFormTC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "olsrv2IibLinkSetInMetric is the metric of the link
           from the OLSRv2 interface with addresses
           L_neighbor_iface_addr_list to this OLSRv2 interface.
           The L_neighbor_iface_addr_list is identified by
           the nhdpDiscIfIndex which is an index to the
           nhdpIibLinkSetTable which this table augments."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2IibLinkSetEntry 1 }

    olsrv2IibLinkSetOutMetric  OBJECT-TYPE
       SYNTAX      Olsrv2MetricValueCompressedFormTC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "olsrv2IibLinkSetOutMetric is the metric of the
           link to the OLSRv2 interface with addresses
           L_neighbor_iface_addr_list from this OLSRv2 interface.
           The L_neighbor_iface_addr_list is identified by
           the nhdpDiscIfIndex which is an index to the
           nhdpIibLinkSetTable which this table augments."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2IibLinkSetEntry 2 }



Herberg, et al.         Expires December 14, 2013              [Page 30]

Internet-Draft               The OLSRv2-MIB                    June 2013


    olsrv2IibLinkSetMprSelector  OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "olsrv2IibLinkSetMprSelector is a boolean flag,
           recording whether this neighbor has selected this router
           as a flooding MPR, i.e., is a flooding MPR selector
           of this router."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2IibLinkSetEntry 3 }

    --
    -- 2-Hop Set; from RFC 6130, extended by OLSRv2 by the
    -- following fields: N2_in_metric, N2_out_metric
    --

    olsrv2Iib2HopSetTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2Iib2HopSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A 2-Hop Set of an interface records network
           addresses of symmetric 2-hop neighbors, and
           the symmetric links to symmetric 1-hop neighbors
           through which these symmetric 2-hop neighbors
           can be reached.  It consists of 2-Hop Tuples."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 2 }

    olsrv2Iib2HopSetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2Iib2HopSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "olsrv2Iib2HopSetTable consists of 2-Hop Tuples,
           each representing a single network address of
           a symmetric 2-hop neighbor, and a single MANET
           interface of a symmetric 1-hop neighbor.
           Each 2-Hop Set from NHDP is extended by
           OLSRv2 by the following fields:




Herberg, et al.         Expires December 14, 2013              [Page 31]

Internet-Draft               The OLSRv2-MIB                    June 2013


           (N2_in_metric (olsrv2Iib2HopSetInMetric),
            N2_out_metric (olsrv2Iib2HopSetOutMetric))"
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       AUGMENTS { nhdpIib2HopSetEntry }
    ::= { olsrv2Iib2HopSetTable 1 }

    Olsrv2Iib2HopSetEntry ::=
       SEQUENCE {
          olsrv2Iib2HopSetInMetric
             Olsrv2MetricValueCompressedFormTC,
          olsrv2Iib2HopSetOutMetric
             Olsrv2MetricValueCompressedFormTC
       }

    olsrv2Iib2HopSetInMetric  OBJECT-TYPE
       SYNTAX      Olsrv2MetricValueCompressedFormTC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "olsrv2Iib2HopSetInMetric is the neighbor metric
           from the router with address N2_2hop_iface_addr
           to the router with OLSRv2 interface addresses
           N2_neighbor_iface_addr_list.

           The N2_2hop_iface_addr is identified by the
           (nhdpIib2HopSetIpAddressType,
           nhdpIib2HopSetIpAddress) pair from the
           nhdpIibLinkSetTable which this table augments.

           The N2_neighbor_iface_addr_list is defined by
           the nhdpDiscIfIndex which is an index of the
           nhdpIibLinkSetTable which this table augments."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013.

           and

           RFC 6779 - Definition of Managed Objects for the
           Neighboorhood Discovery Process, Herberg, U.,
           Cole, R. and I. Chakeres, October 2012."
    ::= { olsrv2Iib2HopSetEntry 1 }

    olsrv2Iib2HopSetOutMetric  OBJECT-TYPE



Herberg, et al.         Expires December 14, 2013              [Page 32]

Internet-Draft               The OLSRv2-MIB                    June 2013


       SYNTAX      Olsrv2MetricValueCompressedFormTC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "olsrv2Iib2HopSetOutMetric is the neighbor metric
           to the router with address N2_2hop_iface_addr
           from the router with OLSRv2 interface addresses
           N2_neighbor_iface_addr_list.

           The N2_2hop_iface_addr is identified by the
           (nhdpIib2HopSetIpAddressType,
           nhdpIib2HopSetIpAddress) pair from the
           nhdpIibLinkSetTable which this table augments.

           The N2_neighbor_iface_addr_list is defined by
           the nhdpDiscIfIndex which is an index of the
           nhdpIibLinkSetTable which this table augments."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013.

           and

           RFC 6779 - Definition of Managed Objects for the
           Neighboorhood Discovery Process, Herberg, U.,
           Cole, R. and I. Chakeres, October 2012."
    ::= { olsrv2Iib2HopSetEntry 2 }


    --
    -- Local Information Base  - as defined in RFC 6130,
    -- extended by the addition of an Originator Set,
    -- defined in Section 6.1 and a Local Attached
    -- Network Set, defined in Section 6.2.
    --

    --
    -- Originator Set
    --

    olsrv2LibOrigSetTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2LibOrigSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A router's Originator Set records addresses
           that were recently used as originator addresses



Herberg, et al.         Expires December 14, 2013              [Page 33]

Internet-Draft               The OLSRv2-MIB                    June 2013


           by this router."
        REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 3 }

    olsrv2LibOrigSetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2LibOrigSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A router's Originator Set consists of
           Originator Tuples:

           (O_orig_addr (olsrv2LibOrigSetIpAddrType
            and olsrv2LibOrigSetIpAddr),
            O_time (olsrv2LibOrigSetExpireTime))."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       INDEX { olsrv2LibOrigSetIpAddrType,
               olsrv2LibOrigSetIpAddr }
    ::= { olsrv2LibOrigSetTable 1 }

    Olsrv2LibOrigSetEntry ::=
       SEQUENCE {
          olsrv2LibOrigSetIpAddrType
             InetAddressType,
          olsrv2LibOrigSetIpAddr
             InetAddress,
          olsrv2LibOrigSetExpireTime
             TimeStamp
       }

    olsrv2LibOrigSetIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType { ipv4(1) , ipv6(2) }
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2LibOrigSetIpAddr,
           as defined in the InetAddress MIB (RFC4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol



Herberg, et al.         Expires December 14, 2013              [Page 34]

Internet-Draft               The OLSRv2-MIB                    June 2013


           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2LibOrigSetEntry 1 }

    olsrv2LibOrigSetIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "An originator address recently employed
           by this router."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2LibOrigSetEntry 2 }

    olsrv2LibOrigSetExpireTime  OBJECT-TYPE
       SYNTAX      TimeStamp
       UNITS      "centiseconds"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "olsrv2LibOrigSetExpireTime specifies the value
           of sysUptime when this entry SHOULD expire and be
           removed from the olsrv2LibOrigSetTable.  This time
           is determined at the time the entry is added,
           derived from the following expression:

              O_time := current time + O_HOLD_TIME

           where O_time is olsrv2LibOrigSetExpireTime,
           current_time is current sysUpTime and
           O_HOLD_TIME is a parameter of the OLSRv2
           protocol.  In the event that the
           O_HOLD_TIME is changed, then the
           olsrv2LibOrigSetExpireTime needs to be
           recomputed for each of the entries in this Table."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2LibOrigSetEntry 3 }


    --
    -- Local Attached Network Set
    --



Herberg, et al.         Expires December 14, 2013              [Page 35]

Internet-Draft               The OLSRv2-MIB                    June 2013


    olsrv2LibLocAttNetSetTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2LibLocAttNetSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A router's Local Attached Network Set records
           its local non-OLSRv2 interfaces via which it
           can act as gateways to other networks."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 4 }

    olsrv2LibLocAttNetSetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2LibLocAttNetSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The entries include the Local Attached
           Network Tuples:

           (AL_net_addr, AL_dist, AL_metric)

           where:

              AL_net_addr is the network address
              of an attached network which can
              be reached via this router.  The
              AL_net_addr is defined in this MIB
              module by the tuple
              (olsrv2LibLocAttNetSetIpAddrType,
               olsrv2LibLocAttNetSetIpAddr,
               olsrv2LibLocAttNetSetIpAddrPrefixLen).

              AL_dist is the number of hops to
              the network with address AL_net_addr
              from this router.  The AL_dist is
              defined in this MIB module by the
              olsrv2LibLocAttNetSetDistance object.

              AL_metric is the metric of the link to
              the attached network with address
              AL_net_addr from this router. The
              AL_metric is defined in this MIB module
              by the olsrv2LibLocAttNetSetMetric
              object.




Herberg, et al.         Expires December 14, 2013              [Page 36]

Internet-Draft               The OLSRv2-MIB                    June 2013


           OLSRv2 (RFC XXXX) defines the rules for managing
           entries within this table, e.g., populating
           and purging entries.  Specific instructions for the
           olsrv2LibLocAttNetSetEntry(s) are found in
           Section 7.2 and Section 17 of OLSRv2 (RFC XXXX)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       INDEX { olsrv2LibLocAttNetSetIpAddrType,
               olsrv2LibLocAttNetSetIpAddr,
               olsrv2LibLocAttNetSetIpAddrPrefixLen }
    ::= { olsrv2LibLocAttNetSetTable 1 }

    Olsrv2LibLocAttNetSetEntry ::=
       SEQUENCE {
          olsrv2LibLocAttNetSetIpAddrType
             InetAddressType,
          olsrv2LibLocAttNetSetIpAddr
             InetAddress,
          olsrv2LibLocAttNetSetIpAddrPrefixLen
             InetAddressPrefixLength,
          olsrv2LibLocAttNetSetDistance
             Unsigned32,
          olsrv2LibLocAttNetSetMetric
             Olsrv2MetricValueCompressedFormTC
       }

    olsrv2LibLocAttNetSetIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType { ipv4(1) , ipv6(2) }
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2LibLocAttNetSetIpAddr, as defined
           in the InetAddress MIB (RFC 4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2LibLocAttNetSetEntry 1 }

    olsrv2LibLocAttNetSetIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  not-accessible
       STATUS      current



Herberg, et al.         Expires December 14, 2013              [Page 37]

Internet-Draft               The OLSRv2-MIB                    June 2013


       DESCRIPTION
          "This is the network address of an attached
           network which can be reached via this router."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2LibLocAttNetSetEntry 2 }

    olsrv2LibLocAttNetSetIpAddrPrefixLen  OBJECT-TYPE
       SYNTAX      InetAddressPrefixLength
       UNITS       "bits"
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "Indicates the number of leading one bits that form the
           mask to be logically ANDed with the destination address
           before being compared to the value in the
           olsrv2LibLocAttNetSetIpAddr field."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2LibLocAttNetSetEntry 3 }

    olsrv2LibLocAttNetSetDistance  OBJECT-TYPE
       SYNTAX      Unsigned32 (1..255)
       UNITS       "hops"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object specifies the number of hops
           to the network with address
           olsrv2LibLocAttNetSetIpAddr from this router."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2LibLocAttNetSetEntry 4 }

    olsrv2LibLocAttNetSetMetric  OBJECT-TYPE
       SYNTAX      Olsrv2MetricValueCompressedFormTC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object specifies the metric of the
           link to the attached network with
           address AL_net_addr from this router.  The



Herberg, et al.         Expires December 14, 2013              [Page 38]

Internet-Draft               The OLSRv2-MIB                    June 2013


           AL_net_addr is defined by the tuple
           (olsrv2LibLocAttNetSetIpAddrType,
            olsrv2LibLocAttNetSetIpAddr,
            olsrv2LibLocAttNetSetIpAddrPrefixLen)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2LibLocAttNetSetEntry 5 }


    --
    -- Neighbor Information Base  - as defined in RFC 6130,
    -- extended by OLSRv2 by the addition of the following
    -- elements to each Neighbor Tuple
    --

    --
    -- Neighbor Set
    --

    olsrv2NibNeighborSetTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2NibNeighborSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A router's Neighbor Set records all network
           addresses of each 1-hop neighbor. It consists
           of Neighbor Tuples, each representing a single
           1-hop neighbor. "
        REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
     ::= { olsrv2StateGroup 5 }

     olsrv2NibNeighborSetEntry  OBJECT-TYPE
        SYNTAX      Olsrv2NibNeighborSetEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION
           "Each Neighbor Tuple in the Neighbor Set, defined
            in RFC 6130, has these additional elements:
               N_orig_addr (olsrv2NibNeighborSetNOrigIpAddrType,
                            olsrv2NibNeighborSetNOrigIpAddr)
               N_in_metric (olsrv2NibNeighborSetNInMetric)
               N_out_metric (olsrv2NibNeighborSetNOutMetric)
               N_will_flooding (olsrv2NibNeighborSetNWillFlooding)



Herberg, et al.         Expires December 14, 2013              [Page 39]

Internet-Draft               The OLSRv2-MIB                    June 2013


               N_will_routing (olsrv2NibNeighborSetNWillRouting)
               N_flooding_mpr (olsrv2NibNeighborSetNFloodingMpr)
               N_routing_mpr (olsrv2NibNeighborSetNRoutingMpr)
               N_mpr_selector (olsrv2NibNeighborSetNMprSelector)
               N_advertised (olsrv2NibNeighborSetNAdvertised)
            defined here as extensions."
        REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
        AUGMENTS { nhdpNibNeighborSetEntry }
    ::= { olsrv2NibNeighborSetTable 1 }

    Olsrv2NibNeighborSetEntry ::=
       SEQUENCE {
          olsrv2NibNeighborSetNOrigIpAddrType
             InetAddressType,
          olsrv2NibNeighborSetNOrigIpAddr
             InetAddress,
          olsrv2NibNeighborSetNInMetric
             Olsrv2MetricValueCompressedFormTC,
          olsrv2NibNeighborSetNOutMetric
             Olsrv2MetricValueCompressedFormTC,
          olsrv2NibNeighborSetNWillFlooding
             WillingnessTC,
          olsrv2NibNeighborSetNWillRouting
             WillingnessTC,
          olsrv2NibNeighborSetNFloodingMpr
             TruthValue,
          olsrv2NibNeighborSetNRoutingMpr
             TruthValue,
          olsrv2NibNeighborSetNMprSelector
             TruthValue,
          olsrv2NibNeighborSetNAdvertised
             TruthValue
       }

    olsrv2NibNeighborSetNOrigIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType { ipv4(1) , ipv6(2) }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2NibNeighborSetNOrigIpAddr, as defined
           in the InetAddress MIB module (RFC4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE



Herberg, et al.         Expires December 14, 2013              [Page 40]

Internet-Draft               The OLSRv2-MIB                    June 2013


          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 1 }

    olsrv2NibNeighborSetNOrigIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the originator IP address of the neighbor
           represented by this table entry."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 2 }

    olsrv2NibNeighborSetNInMetric  OBJECT-TYPE
       SYNTAX      Olsrv2MetricValueCompressedFormTC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is the neighbor metric of any
           link from this neighbor to an OLSRv2 interface
           of this router, i.e., the minimum of all corresponding
           L_in_metric (olsrv2IibLinkSetInMetric)
           with L_status = SYMMETRIC and
           L_in_metric (olsrv2IibLinkSetInMetric) != UNKNOWN_METRIC,
           UNKNOWN_METRIC if there are no such Link Tuples.
           UNKNOWN_METRIC has a value of 0."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 3 }

    olsrv2NibNeighborSetNOutMetric  OBJECT-TYPE
       SYNTAX      Olsrv2MetricValueCompressedFormTC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is is the neighbor metric of any
           link from an OLSRv2 interface of this router
           to this neighbor, i.e., the minimum of all
           corresponding L_out_metric
           (olsrv2IibLinkSetOutMetric) with L_status =
           SYMMETRIC and L_out_metric



Herberg, et al.         Expires December 14, 2013              [Page 41]

Internet-Draft               The OLSRv2-MIB                    June 2013


           (olsrv2IibLinkSetOutMetric) != UNKNOWN_METRIC,
           UNKNOWN_METRIC if there are no such Link Tuples.
           UNKNOWN_METRIC has a value of 0."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 4 }

    olsrv2NibNeighborSetNWillFlooding  OBJECT-TYPE
       SYNTAX      WillingnessTC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is the neighbor's willingness to be
           selected as a flooding MPR, in the range from
           WILL_NEVER to WILL_ALWAYS, both inclusive, taking
           the value WILL_NEVER if no OLSRv2 specific
           information is received from this neighbor."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 5 }

    olsrv2NibNeighborSetNWillRouting  OBJECT-TYPE
       SYNTAX      WillingnessTC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is the neighbor's willingness to be
           selected as a routing MPR, in the range from
           WILL_NEVER to WILL_ALWAYS, both inclusive, taking
           the value WILL_NEVER if no OLSRv2 specific
           information is received from this neighbor."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 6 }

    olsrv2NibNeighborSetNFloodingMpr  OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is a boolean flag, recording whether
           this neighbor is selected as a flooding MPR



Herberg, et al.         Expires December 14, 2013              [Page 42]

Internet-Draft               The OLSRv2-MIB                    June 2013


           by this router."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 7 }

    olsrv2NibNeighborSetNRoutingMpr  OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is a boolean flag, recording whether
           this neighbor is selected as a routing MPR
           by this router."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 8 }

    olsrv2NibNeighborSetNMprSelector  OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is a boolean flag,
           recording whether this neighbor has selected this router
           as a routing MPR, i.e., is a routing MPR
           selector of this router.

           When set to 'true', then this router is selected as
           a routing MPR by the neighbor router.
           When set to 'false',
           then this router is not selected by the neighbor
           as a routing MPR."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 9 }

    olsrv2NibNeighborSetNAdvertised  OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object, N_mpr_selector



Herberg, et al.         Expires December 14, 2013              [Page 43]

Internet-Draft               The OLSRv2-MIB                    June 2013


           (olsrv2NibNeighborSetNMprSelector), is a boolean flag,
           recording whether this router has elected to
           advertise a link to this neighbor in its TC messages."
        REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NibNeighborSetEntry 10 }


    olsrv2NibNeighborSetTableAnsn OBJECT-TYPE
       SYNTAX      Unsigned32 (0..65535)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "Advertised Neighbor Sequence Number (ANSN), is
           a variable, whose value is included in TC messages to
           indicate the freshness of the information transmitted."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 6 }


    --
    -- Topology Information Base - this Information
    -- Base is specific to OLSRv2, and is defined in
    -- Section 10 of RFC XXXX.
    --

    --
    -- Advertising Remote Router Set
    --

    olsrv2TibAdRemoteRouterSetTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2TibAdRemoteRouterSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A router's Advertising Remote Router Set records
           information describing each remote router in the
           network that transmits TC messages."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 7 }



Herberg, et al.         Expires December 14, 2013              [Page 44]

Internet-Draft               The OLSRv2-MIB                    June 2013


    olsrv2TibAdRemoteRouterSetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2TibAdRemoteRouterSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A router's Advertised Neighbor Set Table entry
           consists of Advertising Remote Router Tuples:

           (AR_orig_addr (olsrv2TibAdRemoteRouterSetIpAddrType,
                          olsrv2TibAdRemoteRouterSetIpAddr),
            AR_seq_number (olsrv2TibAdRemoteRouterSetMaxSeqNo),
            AR_time (olsrv2TibAdRemoteRouterSetExpireTime).

           Addresses associated with this router are
           found in the NHDP-MIB module's nhdpDiscIfSetTable.

           OLSRv2 (RFC XXXX) defines the rules for managing
           entries within this table, e.g., populating
           and purging entries.  Specific instructions for the
           olsrv2TibAdRemoteRouterSetEntry(s) are found in
           Section 10.1 and Section 17 of OLSRv2 (RFC XXXX)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       INDEX { olsrv2TibAdRemoteRouterSetIpAddrType,
               olsrv2TibAdRemoteRouterSetIpAddr }
    ::= { olsrv2TibAdRemoteRouterSetTable 1 }

    Olsrv2TibAdRemoteRouterSetEntry ::=
       SEQUENCE {
          olsrv2TibAdRemoteRouterSetIpAddrType
             InetAddressType,
          olsrv2TibAdRemoteRouterSetIpAddr
             InetAddress,
          olsrv2TibAdRemoteRouterSetMaxSeqNo
             Unsigned32,
          olsrv2TibAdRemoteRouterSetExpireTime
             TimeStamp
       }

    olsrv2TibAdRemoteRouterSetIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType { ipv4(1) , ipv6(2) }
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibAdRemoteRouterSetIpAddr,
           as defined in the InetAddress MIB module (RFC4001).



Herberg, et al.         Expires December 14, 2013              [Page 45]

Internet-Draft               The OLSRv2-MIB                    June 2013


           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAdRemoteRouterSetEntry 1 }

    olsrv2TibAdRemoteRouterSetIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "This is the originator address of a received
           TC message."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAdRemoteRouterSetEntry 2 }

    olsrv2TibAdRemoteRouterSetMaxSeqNo  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..65535)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the greatest ANSN in any TC message
           received which originated from the router
           with originator address
           olsrv2TibAdRemoteRouterSetIpAddr."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAdRemoteRouterSetEntry 3 }

    olsrv2TibAdRemoteRouterSetExpireTime  OBJECT-TYPE
       SYNTAX      TimeStamp
       UNITS       "centiseconds"
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "olsrv2TibAdRemoteRouterSetExpireTime specifies the value
           of sysUptime when this entry SHOULD expire and be
           removed from the olsrv2TibAdRemoteRouterSetTable."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.



Herberg, et al.         Expires December 14, 2013              [Page 46]

Internet-Draft               The OLSRv2-MIB                    June 2013


           and U. Herberg, March 2013."
    ::= { olsrv2TibAdRemoteRouterSetEntry 4 }



    --
    -- Router Topology Set
    --

    olsrv2TibRouterTopologySetTable OBJECT-TYPE
       SYNTAX       SEQUENCE OF Olsrv2TibTopologySetEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
          "A router's Router Topology Set records topology
           information about the network."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 8 }

    olsrv2TibRouterTopologySetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2TibTopologySetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "It consists of Router Topology Tuples:

           (TR_from_orig_addr
              (olsrv2TibRouterTopologySetFromOrigIpAddrType,
               olsrv2TibRouterTopologySetFromOrigIpAddr),
            TR_to_orig_addr
              (olsrv2TibRouterTopologySetToOrigIpAddrType,
               olsrv2TibRouterTopologySetToOrigIpAddr),
            TR_seq_number (olsrv2TibRouterTopologySetSeqNo),
            TR_metric (olsrv2TibRouterTopologySetMetric),
            TR_time (olsrv2TibRouterTopologySetExpireTime)).

           OLSRv2 (RFC XXXX) defines the rules for managing
           entries within this table, e.g., populating
           and purging entries.  Specific instructions for the
           olsrv2TibRouterTopologySetEntry(s) are found in
           Section 10.2 and Section 17 of OLSRv2 (RFC XXXX)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."



Herberg, et al.         Expires December 14, 2013              [Page 47]

Internet-Draft               The OLSRv2-MIB                    June 2013


       INDEX { olsrv2TibRouterTopologySetFromOrigIpAddrType,
               olsrv2TibRouterTopologySetFromOrigIpAddr,
               olsrv2TibRouterTopologySetToOrigIpAddrType,
               olsrv2TibRouterTopologySetToOrigIpAddr }
    ::= { olsrv2TibRouterTopologySetTable 1 }

    Olsrv2TibTopologySetEntry ::=
       SEQUENCE {
          olsrv2TibRouterTopologySetFromOrigIpAddrType
             InetAddressType,
          olsrv2TibRouterTopologySetFromOrigIpAddr
             InetAddress,
          olsrv2TibRouterTopologySetToOrigIpAddrType
             InetAddressType,
          olsrv2TibRouterTopologySetToOrigIpAddr
             InetAddress,
          olsrv2TibRouterTopologySetSeqNo
             Unsigned32,
          olsrv2TibRouterTopologySetMetric
             Olsrv2MetricValueCompressedFormTC,
          olsrv2TibRouterTopologySetExpireTime
             TimeStamp
       }

    olsrv2TibRouterTopologySetFromOrigIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType { ipv4(1) , ipv6(2) }
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibRouterTopologySetFromOrigIpAddr,
           as defined in the InetAddress MIB module (RFC4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRouterTopologySetEntry 1 }

    olsrv2TibRouterTopologySetFromOrigIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "This is the originator address of a router which can
           reach the router with originator address TR_to_orig_addr
           in one hop."



Herberg, et al.         Expires December 14, 2013              [Page 48]

Internet-Draft               The OLSRv2-MIB                    June 2013


       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRouterTopologySetEntry 2 }

    olsrv2TibRouterTopologySetToOrigIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType { ipv4(1) , ipv6(2) }
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibRouterTopologySetToOrigIpAddr,
           as defined in the InetAddress MIB module (RFC4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRouterTopologySetEntry 3 }

    olsrv2TibRouterTopologySetToOrigIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "This is the originator address of a router which can be
           reached by the router with originator address
           TR_to_orig_addr in one hop."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRouterTopologySetEntry 4 }

    olsrv2TibRouterTopologySetSeqNo  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..65535)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the greatest Assigned Neighbor Sequence
           Number (ANSN) in any TC message
           received which originated from the router
           with originator address TR_from_orig_addr,
           i.e., which contributed to the information
           contained in this Tuple and is defined by the
           objects:



Herberg, et al.         Expires December 14, 2013              [Page 49]

Internet-Draft               The OLSRv2-MIB                    June 2013


              (olsrv2TibRouterTopologySetFromOrigIpAddrType,
               olsrv2TibRouterTopologySetFromOrigIpAddr).

           Sequence numbers are used in the OLSRv2 protocol
           for the purpose of discarding 'old' information,
           i.e., messages received out of order.  However
           with a limited number of bits for representing
           sequence numbers, wrap-around (that the sequence
           number is incremented from the maximum possible
           value to zero) will occur.  To prevent this from
           interfering with the operation of this protocol,
           the following MUST be observed when determining
           the ordering of sequence numbers.

           The term MAXVALUE designates in the following one
           more than the largest possible value for a sequence
           number.  For a 16 bit sequence number (as are those
           defined in this specification) MAXVALUE is 65536.

           The sequence number S1 is said to be 'greater than'
           the sequence number S2 if:

              o  S1 > S2 AND S1 - S2 < MAXVALUE/2 OR

              o  S2 > S1 AND S2 - S1 > MAXVALUE/2

           When sequence numbers S1 and S2 differ by MAXVALUE/2
           their ordering cannot be determined.  In this case,
           which should not occur, either ordering may be
           assumed.

           Thus when comparing two messages, it is possible
           - even in the presence of wrap-around - to determine
           which message contains the most recent information."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRouterTopologySetEntry 5 }

    olsrv2TibRouterTopologySetMetric  OBJECT-TYPE
       SYNTAX      Olsrv2MetricValueCompressedFormTC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the neighbor metric from the router
           with originator address TR_from_orig_addr
           (olsrv2TibRouterTopologySetFromOrigIpAddrType,



Herberg, et al.         Expires December 14, 2013              [Page 50]

Internet-Draft               The OLSRv2-MIB                    June 2013


           olsrv2TibRouterTopologySetFromOrigIpAddr) to
           the router with originator address TR_to_orig_addr
           (olsrv2TibRouterTopologySetToOrigIpAddrType,
           olsrv2TibRouterTopologySetToOrigIpAddr)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRouterTopologySetEntry 6 }

    olsrv2TibRouterTopologySetExpireTime  OBJECT-TYPE
       SYNTAX      TimeStamp
       UNITS       "centiseconds"
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "olsrv2TibRouterTopologySetExpireTime specifies the value
           of sysUptime when this entry SHOULD expire and be
           removed from the olsrv2TibRouterTopologySetTable."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRouterTopologySetEntry 7 }


    --
    -- Routable Address Topology Set
    --

    olsrv2TibRoutableAddressTopologySetTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2TibRoutableAddressTopologySetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A router's Routable Address Topology Set records topology
           information about the routable addresses within the MANET,
           and via which routers they may be reached."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 9 }

    olsrv2TibRoutableAddressTopologySetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2TibRoutableAddressTopologySetEntry
       MAX-ACCESS  not-accessible
       STATUS      current



Herberg, et al.         Expires December 14, 2013              [Page 51]

Internet-Draft               The OLSRv2-MIB                    June 2013


       DESCRIPTION
          "It consists of Router Topology Tuples:

           (TA_from_orig_addr
                (olsrv2TibRoutableAddressTopologySetFromOrigIpAddrType
                 olsrv2TibRoutableAddressTopologySetFromOrigIpAddr),
            TA_dest_addr
                (olsrv2TibRoutableAddressTopologySetFromDestIpAddrType
                 olsrv2TibRoutableAddressTopologySetFromDestIpAddr),
            TA_seq_number (olsrv2TibRoutableAddressTopologySetSeqNo)
            TA_metric (olsrv2TibRoutableAddressTopologySetMetric)
            TA_time (olsrv2TibRoutableAddressTopologySetExpireTime)
           )

           OLSRv2 (RFC XXXX) defines the rules for managing
           entries within this table, e.g., populating
           and purging entries.  Specific instructions for the
           olsrv2TibRoutableAddressTopologySetEntry(s) are found
           in Section 10.3 and Section 17 of OLSRv2 (RFC XXXX)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       INDEX { olsrv2TibRoutableAddressTopologySetFromOrigIpAddrType,
               olsrv2TibRoutableAddressTopologySetFromOrigIpAddr,
               olsrv2TibRoutableAddressTopologySetDestIpAddrType,
               olsrv2TibRoutableAddressTopologySetDestIpAddr }
    ::= { olsrv2TibRoutableAddressTopologySetTable 1 }

     Olsrv2TibRoutableAddressTopologySetEntry ::=
        SEQUENCE {
           olsrv2TibRoutableAddressTopologySetFromOrigIpAddrType
             InetAddressType,
           olsrv2TibRoutableAddressTopologySetFromOrigIpAddr
             InetAddress,
           olsrv2TibRoutableAddressTopologySetDestIpAddrType
             InetAddressType,
           olsrv2TibRoutableAddressTopologySetDestIpAddr
             InetAddress,
           olsrv2TibRoutableAddressTopologySetSeqNo
             Unsigned32,
           olsrv2TibRoutableAddressTopologySetMetric
             Olsrv2MetricValueCompressedFormTC,
           olsrv2TibRoutableAddressTopologySetExpireTime
             TimeStamp
        }

    olsrv2TibRoutableAddressTopologySetFromOrigIpAddrType  OBJECT-TYPE



Herberg, et al.         Expires December 14, 2013              [Page 52]

Internet-Draft               The OLSRv2-MIB                    June 2013


       SYNTAX      InetAddressType { ipv4(1) , ipv6(2) }
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The type of the
           olsrv2TibRoutableAddressTopologySetFromOrigIpAddr,
           as defined in the InetAddress MIB module (RFC 4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutableAddressTopologySetEntry 1 }

    olsrv2TibRoutableAddressTopologySetFromOrigIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "This is the originator address of a router which can
           reach the router with routable address TA_dest_addr
           in one hop."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutableAddressTopologySetEntry 2 }

    olsrv2TibRoutableAddressTopologySetDestIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType { ipv4(1) , ipv6(2) }
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibRouterTopologySetToOrigIpAddr,
           as defined in the InetAddress MIB module (RFC 4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutableAddressTopologySetEntry 3 }

    olsrv2TibRoutableAddressTopologySetDestIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))



Herberg, et al.         Expires December 14, 2013              [Page 53]

Internet-Draft               The OLSRv2-MIB                    June 2013


       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "This is a routable address of a router which can be
           reached by the router with originator address
           TA_from_orig_addr in one hop.  The TA_from_orig_addr
           is defined by the tuple
           (olsrv2TibRoutableAddressTopologySetFromOrigIpAddrType
            olsrv2TibRoutableAddressTopologySetFromOrigIpAddr)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutableAddressTopologySetEntry 4 }

    olsrv2TibRoutableAddressTopologySetSeqNo  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..65535)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the greatest ANSN in any TC message
           received which originated from the router
           with originator address TA_from_orig_addr,
           i.e., which contributed to the information
           contained in this Tuple.  The TA_from_orig_addr
           is defined by the tuple
           (olsrv2TibRoutableAddressTopologySetFromOrigIpAddrType
            olsrv2TibRoutableAddressTopologySetFromOrigIpAddr)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutableAddressTopologySetEntry 5 }

    olsrv2TibRoutableAddressTopologySetMetric  OBJECT-TYPE
       SYNTAX      Olsrv2MetricValueCompressedFormTC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This is the neighbor metric from the router
           with originator address TA_from_orig_addr (defined
           by the tuple
           (olsrv2TibRoutableAddressTopologySetFromOrigIpAddrType
            olsrv2TibRoutableAddressTopologySetFromOrigIpAddr))
           to the router with OLSRv2 interface address TA_dest_addr
           (defined by the tuple
           (olsrv2TibRoutableAddressTopologySetFromDestIpAddrType
            olsrv2TibRoutableAddressTopologySetFromDestIpAddr))."



Herberg, et al.         Expires December 14, 2013              [Page 54]

Internet-Draft               The OLSRv2-MIB                    June 2013


       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutableAddressTopologySetEntry 6 }

    olsrv2TibRoutableAddressTopologySetExpireTime  OBJECT-TYPE
       SYNTAX      TimeStamp
       UNITS       "centiseconds"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "olsrv2TibRoutableAddressTopologySetExpireTime
           specifies the value of sysUptime when this entry
           SHOULD expire and be removed from the
           olsrv2TibRoutableAddressTopologySetTable."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutableAddressTopologySetEntry 7 }


    --
    -- Attached Network Set
    --

    olsrv2TibAttNetworksSetTable OBJECT-TYPE
       SYNTAX       SEQUENCE OF Olsrv2TibAttNetworksSetEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
          "A router's Attached Network Set records information
           about networks (which may be outside the MANET)
           attached to other routers and their routable addresses."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 10 }

    olsrv2TibAttNetworksSetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2TibAttNetworksSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "It consists of Attached Network Tuples:




Herberg, et al.         Expires December 14, 2013              [Page 55]

Internet-Draft               The OLSRv2-MIB                    June 2013


           (AN_orig_addr
              (olsrv2TibAttNetworksSetOrigIpAddrType,
               olsrv2TibAttNetworksSetOrigIpAddr),
            AN_net_addr
              (olsrv2TibAttNetworksSetNetIpAddrType,
               olsrv2TibAttNetworksSetNetIpAddr,
               olsrv2TibAttNetworksSetNetIpAddrPrefixLen),
            AN_seq_number (olsrv2TibAttNetworksSetSeqNo),
            AN_dist (olsrv2TibAttNetworksSetDist),
            AN_metric (olsrv2TibAttNetworksSetMetric),
            AN_time (olsrv2TibAttNetworksSetExpireTime)
           )

           OLSRv2 (RFC XXXX) defines the rules for managing
           entries within this table, e.g., populating
           and purging entries.  Specific instructions for the
           olsrv2TibRoutableAddressTopologySetEntry(s) are found
           in Section 10.4 and Section 17 of OLSRv2 (RFC XXXX)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
       INDEX { olsrv2TibAttNetworksSetOrigIpAddrType,
               olsrv2TibAttNetworksSetOrigIpAddr,
               olsrv2TibAttNetworksSetNetIpAddrType,
               olsrv2TibAttNetworksSetNetIpAddr,
               olsrv2TibAttNetworksSetNetIpAddrPrefixLen }
    ::= { olsrv2TibAttNetworksSetTable 1 }

    Olsrv2TibAttNetworksSetEntry ::=
       SEQUENCE {
          olsrv2TibAttNetworksSetOrigIpAddrType
             InetAddressType,
          olsrv2TibAttNetworksSetOrigIpAddr
             InetAddress,
          olsrv2TibAttNetworksSetNetIpAddrType
             InetAddressType,
          olsrv2TibAttNetworksSetNetIpAddr
             InetAddress,
          olsrv2TibAttNetworksSetNetIpAddrPrefixLen
             InetAddressPrefixLength,
          olsrv2TibAttNetworksSetSeqNo
             Unsigned32,
          olsrv2TibAttNetworksSetDist
             Unsigned32,
          olsrv2TibAttNetworksSetMetric
             Olsrv2MetricValueCompressedFormTC,
          olsrv2TibAttNetworksSetExpireTime



Herberg, et al.         Expires December 14, 2013              [Page 56]

Internet-Draft               The OLSRv2-MIB                    June 2013


             TimeStamp
       }

    olsrv2TibAttNetworksSetOrigIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType { ipv4(1) , ipv6(2) }
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibAttNetworksSetOrigIpAddr,
           as defined in the InetAddress MIB module (RFC4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 1 }


    olsrv2TibAttNetworksSetOrigIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "This is the originator address, of type
           olsrv2TibAttNetworksSetOrigIpAddrType, of a
           router which can act as gateway to the
           network with address AN_net_addr.  The
           AN_net_addr is defined by the tuple
              (olsrv2TibAttNetworksSetNetIpAddrType,
               olsrv2TibAttNetworksSetNetIpAddr,
               olsrv2TibAttNetworksSetNetIpAddrPrefixLen)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 2 }

    olsrv2TibAttNetworksSetNetIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType { ipv4(1) , ipv6(2) }
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibAttNetworksSetNetIpAddr,
           as defined in the InetAddress MIB module (RFC 4001).

           Only the values 'ipv4(1)' and



Herberg, et al.         Expires December 14, 2013              [Page 57]

Internet-Draft               The OLSRv2-MIB                    June 2013


           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 3 }

    olsrv2TibAttNetworksSetNetIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "This is is the network address,of type
           olsrv2TibAttNetworksSetNetIpAddrType, of an
           attached network, which may be reached via
           the router with originator address AN_orig_addr.
           The AN_orig_addr is defined by the tuple
              (olsrv2TibAttNetworksSetOrigIpAddrType,
               olsrv2TibAttNetworksSetOrigIpAddr)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 4 }

    olsrv2TibAttNetworksSetNetIpAddrPrefixLen  OBJECT-TYPE
       SYNTAX      InetAddressPrefixLength
       UNITS       "bits"
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "Indicates the number of leading one bits that form the
           mask to be logically ANDed with the destination address
           before being compared to the value in the
           olsrv2TibAttNetworksSetNetIpAddr field."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 5 }

    olsrv2TibAttNetworksSetSeqNo  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..65535)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The greatest ANSN in any TC
           message received which originated from the



Herberg, et al.         Expires December 14, 2013              [Page 58]

Internet-Draft               The OLSRv2-MIB                    June 2013


           router with originator address AN_orig_addr
           (i.e., which contributed to the information
           contained in this Tuple).  The AN_orig_addr
           is defined by the tuple
              (olsrv2TibAttNetworksSetOrigIpAddrType,
               olsrv2TibAttNetworksSetOrigIpAddr)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 6 }

    olsrv2TibAttNetworksSetDist  OBJECT-TYPE
       SYNTAX      Unsigned32 (0..255)
       UNITS       "hops"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The number of hops to the network
           with address AN_net_addr from the router with
           originator address AN_orig_addr.
           The AN_orig_addr is defined by the tuple
              (olsrv2TibAttNetworksSetOrigIpAddrType,
               olsrv2TibAttNetworksSetOrigIpAddr)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 7 }

    olsrv2TibAttNetworksSetMetric  OBJECT-TYPE
       SYNTAX      Olsrv2MetricValueCompressedFormTC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The metric of the link from the router with
           originator address AN_orig_addr to the attached
           network with address AN_net_addr.
           The AN_net_addr is defined by the tuple
             (olsrv2TibAttNetworksSetNetIpAddrType,
              olsrv2TibAttNetworksSetNetIpAddr,
              olsrv2TibAttNetworksSetNetIpAddrPrefixLen)."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 9 }




Herberg, et al.         Expires December 14, 2013              [Page 59]

Internet-Draft               The OLSRv2-MIB                    June 2013


    olsrv2TibAttNetworksSetExpireTime  OBJECT-TYPE
       SYNTAX      TimeStamp
       UNITS       "centiseconds"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "olsrv2TibAttNetworksSetExpireTime
           specifies the value of sysUptime when this
           entry SHOULD expire and be removed from the
           olsrv2TibAttNetworksSetTable."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibAttNetworksSetEntry 10 }



    --
    -- Routing Set
    --

    olsrv2TibRoutingSetTable OBJECT-TYPE
       SYNTAX       SEQUENCE OF Olsrv2TibRoutingSetEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
          "A router's Routing Set records the first hop along a
           selected path to each destination for which any such
           path is known."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2StateGroup 11 }

    olsrv2TibRoutingSetEntry  OBJECT-TYPE
       SYNTAX      Olsrv2TibRoutingSetEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "It consists of Routing Tuples:

            (R_dest_addr, R_next_iface_addr,
             R_local_iface_addr, R_dist, R_metric)"
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.



Herberg, et al.         Expires December 14, 2013              [Page 60]

Internet-Draft               The OLSRv2-MIB                    June 2013


           and U. Herberg, March 2013."
       INDEX { olsrv2TibRoutingSetDestIpAddrType,
               olsrv2TibRoutingSetDestIpAddr,
               olsrv2TibRoutingSetDestIpAddrPrefixLen }
    ::= { olsrv2TibRoutingSetTable 1 }

    Olsrv2TibRoutingSetEntry ::=
       SEQUENCE {
          olsrv2TibRoutingSetDestIpAddrType
             InetAddressType,
          olsrv2TibRoutingSetDestIpAddr
             InetAddress,
          olsrv2TibRoutingSetDestIpAddrPrefixLen
             InetAddressPrefixLength,
          olsrv2TibRoutingSetNextIfIpAddrType
             InetAddressType,
          olsrv2TibRoutingSetNextIfIpAddr
             InetAddress,
          olsrv2TibRoutingSetLocalIfIpAddrType
             InetAddressType,
          olsrv2TibRoutingSetLocalIfIpAddr
             InetAddress,
          olsrv2TibRoutingSetDist
             Unsigned32,
          olsrv2TibRoutingSetMetric
             Olsrv2MetricValueCompressedFormTC
       }

    olsrv2TibRoutingSetDestIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType { ipv4(1) , ipv6(2) }
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibRoutingSetDestIpAddr,
           as defined in the InetAddress MIB module (RFC 4001).

           Only the values 'ipv4(1)' and 'ipv6(2)' are
           supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 1 }

    olsrv2TibRoutingSetDestIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  not-accessible
       STATUS      current



Herberg, et al.         Expires December 14, 2013              [Page 61]

Internet-Draft               The OLSRv2-MIB                    June 2013


       DESCRIPTION
          "This is the address of the destination,
           either the address of an interface of
           a destination router, or the network
           address of an attached network."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 2 }

    olsrv2TibRoutingSetDestIpAddrPrefixLen  OBJECT-TYPE
       SYNTAX      InetAddressPrefixLength
       UNITS       "bits"
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "Indicates the number of leading one bits that form the
           mask to be logically ANDed with the destination address
           before being compared to the value in the
           olsrv2TibRoutingSetDestIpAddr field.

           Note: This definition needs to be consistent
           with the current forwarding table MIB module description.
           Specifically, it SHOULD allow for longest prefix
           matching of network addresses."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 3 }

    olsrv2TibRoutingSetNextIfIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType { ipv4(1) , ipv6(2) }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibRoutingSetNextIfIpAddr,
           as defined in the InetAddress MIB module (RFC 4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 4 }




Herberg, et al.         Expires December 14, 2013              [Page 62]

Internet-Draft               The OLSRv2-MIB                    June 2013


    olsrv2TibRoutingSetNextIfIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is the OLSRv2 interface address of the
           next hop on the selected path to the
           destination."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 5 }

    olsrv2TibRoutingSetLocalIfIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType { ipv4(1) , ipv6(2) }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2TibRoutingSetLocalIfIpAddr
           and olsrv2TibRoutingSetNextIfIpAddr,
           as defined in the InetAddress MIB module (RFC 4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 6 }


    olsrv2TibRoutingSetLocalIfIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is the address of the local OLSRv2
           interface over which a packet must be
           sent to reach the destination by the
           selected path."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 7 }

    olsrv2TibRoutingSetDist  OBJECT-TYPE



Herberg, et al.         Expires December 14, 2013              [Page 63]

Internet-Draft               The OLSRv2-MIB                    June 2013


       SYNTAX      Unsigned32 (0..255)
       UNITS       "hops"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is the number of hops on the selected
           path to the destination."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 8 }

    olsrv2TibRoutingSetMetric  OBJECT-TYPE
       SYNTAX      Olsrv2MetricValueCompressedFormTC
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This object is the metric of the route
           to the destination with address R_dest_addr."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2TibRoutingSetEntry 9 }




 --
 -- OLSRv2 Performance Group
 --

 --
 --    Contains objects which help to characterize the
 --    performance of the OLSRv2 routing process.
 --

 olsrv2PerformanceObjGrp  OBJECT IDENTIFIER ::= {olsrv2MIBObjects 3}

     --
     -- Objects per local interface
     --

    olsrv2InterfacePerfTable  OBJECT-TYPE
       SYNTAX      SEQUENCE OF Olsrv2InterfacePerfEntry
       MAX-ACCESS  not-accessible
       STATUS      current



Herberg, et al.         Expires December 14, 2013              [Page 64]

Internet-Draft               The OLSRv2-MIB                    June 2013


       DESCRIPTION
          "This table summarizes performance objects that are
           measured per each active local OLSRv2 interface.
           If the olsrv2InterfaceAdminStatus of the interface
           changes to 'disabled' then the row associated with this
           interface SHOULD be removed from this table."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2PerformanceObjGrp 1 }

    olsrv2InterfacePerfEntry OBJECT-TYPE
       SYNTAX      Olsrv2InterfacePerfEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "A single entry contains performance counters for
           each active local OLSRv2 interface."
       AUGMENTS { nhdpInterfacePerfEntry }
    ::= { olsrv2InterfacePerfTable 1 }

    Olsrv2InterfacePerfEntry ::=
       SEQUENCE {
          olsrv2IfTcMessageXmits
             Counter32,
          olsrv2IfTcMessageRecvd
             Counter32,
          olsrv2IfTcMessageXmitAccumulatedSize
             Counter64,
          olsrv2IfTcMessageRecvdAccumulatedSize
             Counter64,
          olsrv2IfTcMessageTriggeredXmits
             Counter32,
          olsrv2IfTcMessagePeriodicXmits
             Counter32,
          olsrv2IfTcMessageForwardedXmits
             Counter32,
          olsrv2IfTcMessageXmitAccumulatedMPRSelectorCount
             Counter32
       }

    olsrv2IfTcMessageXmits  OBJECT-TYPE
       SYNTAX      Counter32
       UNITS       "messages"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION



Herberg, et al.         Expires December 14, 2013              [Page 65]

Internet-Draft               The OLSRv2-MIB                    June 2013


          "A counter is incremented each time a TC
           message has been transmitted on that interface."
    ::= { olsrv2InterfacePerfEntry 1 }

    olsrv2IfTcMessageRecvd  OBJECT-TYPE
       SYNTAX      Counter32
       UNITS       "messages"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "A counter is incremented each time a
           TC message has been received on that interface.
           This excludes all messages that are ignored due to
           OLSRv2 protocol procedures."
    ::= { olsrv2InterfacePerfEntry 2 }

    olsrv2IfTcMessageXmitAccumulatedSize  OBJECT-TYPE
       SYNTAX      Counter64
       UNITS       "octets"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "A counter is incremented by the number of octets in
           a TC message each time a TC message has been sent."
    ::= { olsrv2InterfacePerfEntry 3 }

    olsrv2IfTcMessageRecvdAccumulatedSize  OBJECT-TYPE
       SYNTAX      Counter64
       UNITS       "octets"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "A counter is incremented by the number of octets in
           a TC message each time a TC message has been received.
           This excludes all messages that are ignored due to
           OLSRv2 protocol procedures."
    ::= { olsrv2InterfacePerfEntry 4 }

    olsrv2IfTcMessageTriggeredXmits  OBJECT-TYPE
       SYNTAX      Counter32
       UNITS       "messages"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "A counter is incremented each time a triggered
           TC message has been sent."
    ::= { olsrv2InterfacePerfEntry 5 }




Herberg, et al.         Expires December 14, 2013              [Page 66]

Internet-Draft               The OLSRv2-MIB                    June 2013


    olsrv2IfTcMessagePeriodicXmits  OBJECT-TYPE
       SYNTAX      Counter32
        UNITS      "messages"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "A counter is incremented each time a periodic
           TC message has been sent."
    ::= { olsrv2InterfacePerfEntry 6 }

    olsrv2IfTcMessageForwardedXmits  OBJECT-TYPE
       SYNTAX      Counter32
       UNITS       "messages"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "A counter is incremented each time a
           TC message has been forwarded."
    ::= { olsrv2InterfacePerfEntry 7 }

    olsrv2IfTcMessageXmitAccumulatedMPRSelectorCount OBJECT-TYPE
       SYNTAX      Counter32
       UNITS       "advertised MPR selectors"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "A counter is incremented by the number of advertised
           MPR selectors in a TC each time a TC
           message has been sent."
    ::= { olsrv2InterfacePerfEntry 8 }



    --
    -- Objects concerning the Routing set
    --

    olsrv2RoutingSetRecalculationCount  OBJECT-TYPE
       SYNTAX      Counter32
       UNITS       "recalculations"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This counter increments each time the Routing Set has
           been recalculated."
    ::= { olsrv2PerformanceObjGrp 2 }

    --



Herberg, et al.         Expires December 14, 2013              [Page 67]

Internet-Draft               The OLSRv2-MIB                    June 2013


    -- Objects concerning the MPR set
    --

    olsrv2MPRSetRecalculationCount  OBJECT-TYPE
       SYNTAX      Counter32
       UNITS       "recalculations"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "This counter increments each time the MPRs
           of this router have been recalculated for
           any of its interfaces."
    ::= { olsrv2PerformanceObjGrp 3 }





 --
 -- Notifications
 --

 olsrv2NotificationsObjects OBJECT IDENTIFIER ::=
                                      { olsrv2MIBNotifications 0 }
 olsrv2NotificationsControl OBJECT IDENTIFIER ::=
                                      { olsrv2MIBNotifications 1 }
 olsrv2NotificationsStates  OBJECT IDENTIFIER ::=
                                      { olsrv2MIBNotifications 2 }


    -- olsrv2NotificationsObjects

    olsrv2RouterStatusChange NOTIFICATION-TYPE
        OBJECTS { olsrv2OrigIpAddrType, -- The address type of
                                        --    the originator of
                                        --    the notification.
                  olsrv2OrigIpAddr,     -- The originator of
                                        --    the notification.
                  olsrv2AdminStatus     -- The new state.
        }
        STATUS      current
        DESCRIPTION
           "olsrv2RouterStatusChange is a notification generated
            when the OLSRv2 router changes it status.
            The router status is maintained in the
            olsrv2AdminStatus object."
    ::= { olsrv2NotificationsObjects 1 }




Herberg, et al.         Expires December 14, 2013              [Page 68]

Internet-Draft               The OLSRv2-MIB                    June 2013


    olsrv2OrigIpAddrChange NOTIFICATION-TYPE
       OBJECTS { olsrv2OrigIpAddrType, -- The address type of
                                       --    the originator of
                                       --    the notification.
                 olsrv2OrigIpAddr,     -- The originator of
                                       --    the notification.
                 olsrv2PreviousOrigIpAddrType, -- The address
                                       -- type of previous
                                       -- address of
                                       -- the originator of
                                       -- the notification.
                 olsrv2PreviousOrigIpAddr  -- The previous
                                       -- address of the
                                       -- originator of
                                       -- the notification.
       }
       STATUS      current
       DESCRIPTION
          "olsrv2OrigIpAddrChange is a notification generated when
           the OLSRv2 router changes it originator IP address.
           The notification includes the new and the previous
           originator IP address of the OLSRv2 router."
    ::= { olsrv2NotificationsObjects 2 }

    olsrv2RoutingSetRecalculationCountChange NOTIFICATION-TYPE
       OBJECTS { olsrv2OrigIpAddrType, -- The address type of
                                       --   the originator of
                                       --   the notification.
                 olsrv2OrigIpAddr,     -- The originator of
                                       --   the notification.
                 olsrv2RoutingSetRecalculationCount  -- Number
                                           -- of the
                                           -- routing set
                                           -- recalculations.
       }
       STATUS       current
       DESCRIPTION
          "The olsrv2RoutingSetRecalculationCountChange
           notification is generated when a significant number of
           routing set recalculations have occurred in a short time.
           This notification SHOULD be generated no more than once
           per olsrv2RoutingSetRecalculationCountWindow.
           The network administrator SHOULD select
           appropriate values for 'significant number of
           routing set recalculations' and 'short time' through
           the settings of the
           olsrv2RoutingSetRecalculationCountThreshold
           and olsrv2RoutingSetRecalculationCountWindow objects."



Herberg, et al.         Expires December 14, 2013              [Page 69]

Internet-Draft               The OLSRv2-MIB                    June 2013


    ::= { olsrv2NotificationsObjects 3 }

    olsrv2MPRSetRecalculationCountChange NOTIFICATION-TYPE
       OBJECTS { olsrv2OrigIpAddrType, -- The address type of
                                       --   the originator of
                                       --   the notification.
                 olsrv2OrigIpAddr,     -- The originator of
                                       --   the notification.
                 olsrv2MPRSetRecalculationCount  -- Number of
                                       --   MPR set
                                       --   recalculations.
       }
       STATUS       current
       DESCRIPTION
          "The olsrv2MPRSetRecalculationCountChange
           notification is generated when a significant
           number of MPR set recalculations occur in
           a short period of time.  This notification
           SHOULD be generated no more than once
           per olsrv2MPRSetRecalculationCountWindow.
           The network administrator SHOULD select
           appropriate values for 'significant number of
           MPR set recalculations' and 'short period of
           time' through the settings of the
           olsrv2MPRSetRecalculationCountThreshold and
           olsrv2MPRSetRecalculationCountWindow objects."
    ::= { olsrv2NotificationsObjects 4 }


    -- olsrv2NotificationsControl

    olsrv2RoutingSetRecalculationCountThreshold OBJECT-TYPE
       SYNTAX      Integer32 (0..255)
       UNITS       "recalculations"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "A threshold value for the
           olsrv2RoutingSetRecalculationCount object.
           If the number of occurrences exceeds this
           threshold within the previous
           olsrv2RoutingSetRecalculationCountWindow,
           then the olsrv2RoutingSetRecalculationCountChange
           notification is to be generated.

           It is RECOMMENDED that the value of this
           threshold be set to at least 20 and higher
           in dense topologies with frequent expected



Herberg, et al.         Expires December 14, 2013              [Page 70]

Internet-Draft               The OLSRv2-MIB                    June 2013


           topology changes."
    ::= { olsrv2NotificationsControl 1 }

    olsrv2RoutingSetRecalculationCountWindow OBJECT-TYPE
       SYNTAX      TimeTicks
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "This object is used to determine whether to generate
           an olsrv2RoutingSetRecalculationCountChange notification.
           This object represents an interval from the present moment,
           extending into the past, expressed in hundredths of
           a second.  If the change in the value of the
           olsrv2RoutingSetRecalculationCount object during
           this interval has exceeded the value of
           olsrv2RoutingSetRecalculationCountThreshold, then
           an olsrv2RoutingSetRecalculationCountChange notification
           is generated.

           It is RECOMMENDED that the value for this
           window be set to at least 5 times the
           nhdpHelloInterval."
    ::= { olsrv2NotificationsControl 2 }

    olsrv2MPRSetRecalculationCountThreshold OBJECT-TYPE
       SYNTAX      Integer32 (0..255)
       UNITS       "recalculations"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
          "A threshold value for the
           olsrv2MPRSetRecalculationCount object.
           If the number of occurrences exceeds this
           threshold within the previous
           olsrv2MPRSetRecalculationCountWindow,
           then the
           olsrv2MPRSetRecalculationCountChange
           notification is to be generated.

           It is RECOMMENDED that the value of this
           threshold be set to at least 20 and higher
           in dense topologies with frequent expected
           topology changes."
    ::= { olsrv2NotificationsControl 3 }

    olsrv2MPRSetRecalculationCountWindow OBJECT-TYPE
       SYNTAX       TimeTicks
       MAX-ACCESS   read-write



Herberg, et al.         Expires December 14, 2013              [Page 71]

Internet-Draft               The OLSRv2-MIB                    June 2013


       STATUS       current
       DESCRIPTION
          "This object is used to determine whether to generate
           an olsrv2MPRSetRecalculationCountChange notification.
           This object represents an interval from the present moment,
           extending into the past, expressed in hundredths of
           a second.  If the change in the value of the
           olsrv2MPRSetRecalculationCount object during
           that interval has exceeded the value of
           olsrv2MPRSetRecalculationCountThreshold, then the
           an olsrv2MPRSetRecalculationCountChange notification
           is generated.

           It is RECOMMENDED that the value for this
           window be set to at least 5 times the
           nhdpHelloInterval."
    ::= { olsrv2NotificationsControl 4 }


    olsrv2PreviousOrigIpAddrType  OBJECT-TYPE
       SYNTAX      InetAddressType  { ipv4(1) , ipv6(2) }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The type of the olsrv2PreviousOrigIpAddr,
           as defined in the InetAddress MIB module (RFC 4001).

           Only the values 'ipv4(1)' and
           'ipv6(2)' are supported.

           This object MUST have the same persistence
           characteristics as olsrv2PreviousOrigIpAddr."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NotificationsStates 1 }

    olsrv2PreviousOrigIpAddr  OBJECT-TYPE
       SYNTAX      InetAddress (SIZE(4|16))
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          "The previous origination IP address
           of this OLSRv2 router.

           This object SHOULD be updated each time
           the olsrv2OrigIpAddr is modified.



Herberg, et al.         Expires December 14, 2013              [Page 72]

Internet-Draft               The OLSRv2-MIB                    June 2013


           This object is persistent and when written
           the entity SHOULD save the change to
           non-volatile storage."
       REFERENCE
          "RFC XXXX - The Optimized Link State Routing Protocol
           version 2, Clausen, T., Dearlove, C., Jacquet, P.
           and U. Herberg, March 2013."
    ::= { olsrv2NotificationsStates 2 }



    --
    -- Compliance Statements
    --

    olsrv2Compliances  OBJECT IDENTIFIER ::= { olsrv2MIBConformance 1 }
    olsrv2MIBGroups    OBJECT IDENTIFIER ::= { olsrv2MIBConformance 2 }

    olsrv2BasicCompliance  MODULE-COMPLIANCE
       STATUS current
       DESCRIPTION
          "The basic implementation requirements for
           managed network entities that implement
           the OLSRv2 routing process."
       MODULE  -- this module
       MANDATORY-GROUPS { olsrv2ConfigObjectsGroup }
    ::= { olsrv2Compliances 1 }

    olsrv2FullCompliance MODULE-COMPLIANCE
       STATUS current
       DESCRIPTION
          "The full implementation requirements for
           managed network entities that implement
           the OLSRv2 routing process."
       MODULE  -- this module
       MANDATORY-GROUPS { olsrv2ConfigObjectsGroup,
                          olsrv2StateObjectsGroup,
                          olsrv2PerfObjectsGroup,
                          olsrv2NotificationsObjectsGroup,
                          olsrv2NotificationsGroup }
    ::= { olsrv2Compliances 2 }

    --
    -- Units of Conformance
    --

    olsrv2ConfigObjectsGroup OBJECT-GROUP
       OBJECTS {



Herberg, et al.         Expires December 14, 2013              [Page 73]

Internet-Draft               The OLSRv2-MIB                    June 2013


          olsrv2AdminStatus,
          olsrv2InterfaceAdminStatus,
          olsrv2OrigIpAddrType,
          olsrv2OrigIpAddr,
          olsrv2OHoldTime,
          olsrv2TcInterval,
          olsrv2TcMinInterval,
          olsrv2THoldTime,
          olsrv2AHoldTime,
          olsrv2RxHoldTime,
          olsrv2PHoldTime,
          olsrv2FHoldTime,
          olsrv2TpMaxJitter,
          olsrv2TtMaxJitter,
          olsrv2FMaxJitter,
          olsrv2TcHopLimit,
          olsrv2WillFlooding,
          olsrv2WillRouting,
          olsrv2LinkMetricType
       }
       STATUS      current
       DESCRIPTION
          "Objects to permit configuration of OLSRv2.
           All of these SHOULD be backed by non-volatile
           storage."
    ::= { olsrv2MIBGroups 1 }

    olsrv2StateObjectsGroup  OBJECT-GROUP
       OBJECTS {
          olsrv2LibOrigSetExpireTime,
          olsrv2LibLocAttNetSetDistance,
          olsrv2LibLocAttNetSetMetric,
          olsrv2IibLinkSetInMetric,
          olsrv2IibLinkSetOutMetric,
          olsrv2IibLinkSetMprSelector,
          olsrv2Iib2HopSetInMetric,
          olsrv2Iib2HopSetOutMetric,
          olsrv2NibNeighborSetNOrigIpAddrType,
          olsrv2NibNeighborSetNOrigIpAddr,
          olsrv2NibNeighborSetNInMetric,
          olsrv2NibNeighborSetNOutMetric,
          olsrv2NibNeighborSetNWillFlooding,
          olsrv2NibNeighborSetNWillRouting,
          olsrv2NibNeighborSetNFloodingMpr,
          olsrv2NibNeighborSetNRoutingMpr,
          olsrv2NibNeighborSetNMprSelector,
          olsrv2NibNeighborSetNAdvertised,
          olsrv2NibNeighborSetTableAnsn,



Herberg, et al.         Expires December 14, 2013              [Page 74]

Internet-Draft               The OLSRv2-MIB                    June 2013


          olsrv2TibAdRemoteRouterSetMaxSeqNo,
          olsrv2TibRouterTopologySetSeqNo,
          olsrv2TibRouterTopologySetMetric,
          olsrv2TibRoutableAddressTopologySetExpireTime,
          olsrv2TibRoutableAddressTopologySetSeqNo,
          olsrv2TibRoutableAddressTopologySetMetric,
          olsrv2TibAttNetworksSetSeqNo,
          olsrv2TibAttNetworksSetDist,
          olsrv2TibAttNetworksSetMetric,
          olsrv2TibAttNetworksSetExpireTime,
          olsrv2TibRoutingSetNextIfIpAddrType,
          olsrv2TibRoutingSetNextIfIpAddr,
          olsrv2TibRoutingSetLocalIfIpAddrType,
          olsrv2TibRoutingSetLocalIfIpAddr,
          olsrv2TibRoutingSetDist,
          olsrv2TibRoutingSetMetric
       }
       STATUS      current
       DESCRIPTION
          "Objects to permit monitoring of OLSRv2 state."
    ::= { olsrv2MIBGroups 2 }

    olsrv2PerfObjectsGroup  OBJECT-GROUP
       OBJECTS {
          olsrv2IfTcMessageXmits,
          olsrv2IfTcMessageRecvd,
          olsrv2IfTcMessageXmitAccumulatedSize,
          olsrv2IfTcMessageRecvdAccumulatedSize,
          olsrv2IfTcMessageTriggeredXmits,
          olsrv2IfTcMessagePeriodicXmits,
          olsrv2IfTcMessageForwardedXmits,
          olsrv2IfTcMessageXmitAccumulatedMPRSelectorCount,
          olsrv2RoutingSetRecalculationCount,
          olsrv2MPRSetRecalculationCount
       }
       STATUS      current
       DESCRIPTION
          "Objects to support monitoring of OLSRv2 performance."
    ::= { olsrv2MIBGroups 3 }

    olsrv2NotificationsObjectsGroup OBJECT-GROUP
       OBJECTS {
          olsrv2RoutingSetRecalculationCountThreshold,
          olsrv2RoutingSetRecalculationCountWindow,
          olsrv2MPRSetRecalculationCountThreshold,
          olsrv2MPRSetRecalculationCountWindow,
          olsrv2PreviousOrigIpAddrType,
          olsrv2PreviousOrigIpAddr



Herberg, et al.         Expires December 14, 2013              [Page 75]

Internet-Draft               The OLSRv2-MIB                    June 2013


       }
       STATUS      current
       DESCRIPTION
          "Objects to support the notification types in the
           olsrv2NotificationsGroup.  Some of these appear in
           notification payloads, others serve to control
           notification generation."
    ::= { olsrv2MIBGroups 4 }


    olsrv2NotificationsGroup NOTIFICATION-GROUP
       NOTIFICATIONS {
          olsrv2RouterStatusChange,
          olsrv2OrigIpAddrChange,
          olsrv2RoutingSetRecalculationCountChange,
          olsrv2MPRSetRecalculationCountChange
       }
       STATUS current
       DESCRIPTION
           "Notification types to support management of OLSRv2."
    ::= { olsrv2MIBGroups 5 }

 END


8.  Security Considerations

   This MIB module defines objects for the configuration, monitoring and
   notification of the Optimized Link State Routing protocol version 2
   [OLSRv2].  OLSRv2 allows routers to acquire topological information
   of the routing domain by virtue of exchanging TC message, to
   calculate shortest paths to each destination router in the routing
   domain, to select relays for network-wide transmissions etc.

   There are a number of management objects defined in this MIB module
   with a MAX-ACCESS clause of read-write and/or read-create.  Such
   objects may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.  These are the tables and objects and their
   sensitivity/vulnerability:

   o  olsrv2TcInterval, olsrv2TcMinInterval - these writable objects
      control the rate at which TC messages are sent.  If set at too
      high a rate, this could represent a form of DOS attack by
      overloading interface resources.  If set low, OLSRv2 may not
      converge fast enough to provide accurate routes to all
      destinations in the routing domain.



Herberg, et al.         Expires December 14, 2013              [Page 76]

Internet-Draft               The OLSRv2-MIB                    June 2013


   o  olsrv2TcHopLimit - defines the hop limit for TC messages.  If set
      too low, messages will not be forwarded beyond the defined scope,
      and thus routers further away from the message originator will not
      be able to construct appropriate topology graphs.

   o  olsrv2OHoldTime, olsrv2THoldTime, olsrv2AHoldTime,
      olsrv2RxHoldTime, olsrv2PHoldTime, olsrv2FHoldTime - define hold
      times for tuples of different Information Bases of OLSRv2.  If set
      too low, information will expire quickly, and may this harm a
      correct operation of the routing protocol.

   o  olsrv2WillFlooding and olsrv2WillRouting - define the willingness
      of this router to become MPR.  If this is set to WILL_NEVER (0),
      the managed router will not forward any TC messages, nor accept a
      selection to become MPR by neighboring routers.  If set to
      WILL_ALWAYS (15), the router will be preferred by neighbors during
      MPR selection, and may thus attract more traffic.

   o  olsrv2TpMaxJitter, olsrv2TtMaxJitter, olsrv2FMaxJitter - define
      jitter values for TC message transmission and forwarding.  If set
      too low, control traffic may get lost if the channel is lossy.

   o  olsrv2LinkMetricType - defines the type of the link metric that a
      router uses (e.g., ETX or hop-count).  Whenever this value
      changes, all link metric information recorded by the router is
      invalid, causing a reset of information acquired from other
      routers in the MANET.  Moreover, if olsrv2LinkMetricType on a
      router is set to a value that is not known to other routers in the
      MANET, these routers will not be able to establish routes to that
      router or transiting that router.  Existing routes to the router
      with a olsrv2LinkMetricType unknown to other routers in the MANET
      will be removed.

   Some of the readable objects in this MIB module (i.e., objects with a
   MAX-ACCESS other than not-accessible) may be considered sensitive or
   vulnerable in some network environments.  It is thus important to
   control even GET and/or NOTIFY access to these objects and possibly
   to even encrypt the values of these objects when sending them over
   the network via SNMP.  These are the tables and objects and their
   sensitivity/vulnerability:

   o  olsrv2TibRouterTopologySetTable - The contains information on the
      topology of the MANET, specifically the IP address of the routers
      in the MANET (as identified by
      olsrv2TibRouterTopologySetFromOrigIpAddr and
      olsrv2TibRouterTopologySetToOrigIpAddr objects).  This information
      provides an adversary broad information on the members of the
      MANET, located within this single table.  This information can be



Herberg, et al.         Expires December 14, 2013              [Page 77]

Internet-Draft               The OLSRv2-MIB                    June 2013


      used to expedite attacks on the other members of the MANET without
      having to go through a laborious discovery process on their own.

   Some of the Tables in this MIB AUGMENT Tables defined in NHDP-MIB
   [RFC6779].  Hence, care must be taken in configuring access control
   here in order make sure that the permitted permissions granted for
   the AUGMENT-ing Tables here are consistent with the access controls
   permitted within the NHDP-MIB.  The below list identifies the
   AUGMENT-ing Tables and their NHDP-MIB counterparts.  It is recommend
   that access control policies for these Table pairs are consistently
   set.

   o  The olsrv2InterfaceTable AUGMENTs the nhdpInterfaceTable.

   o  The olsrv2IibLinkSetTable AUGMENTs the nhdpIibLinkSetTable.

   o  The olsrv2Iib2HopSetTable AUGMENTs the nhdpIib2HopSetTable.

   o  The olsrv2NibNeighborSetTable AUGMENTs the
      nhdpNibNeighborSetTable.

   o  The olsrv2InterfacePerfTable AUGMENTs the nhdpInterfacePerfTable.

   MANET technology is often deployed to support communications of
   emergency services or military tactical applications.  In these
   applications, it is imperative to maintain the proper operation of
   the communications network and to protect sensitive information
   related to its operation.  Therefore, when implementing these
   capabilities, the full use of SNMPv3 cryptographic mechanisms for
   authentication and privacy is RECOMMENDED.

   SNMP versions prior to SNMPv3 did not include adequate security.
   Even if the network itself is secure (for example by using IPsec),
   there is no control as to who on the secure network is allowed to
   access and GET/SET (read/change/create/delete) the objects in this
   MIB module.

   Implementations SHOULD provide the security features described by the
   SNMPv3 framework (see [RFC3410]), and implementations claiming
   compliance to the SNMPv3 standard MUST include full support for
   authentication and privacy via the User-based Security Model (USM)
   [RFC3414] with the AES cipher algorithm [RFC3826].  Implementations
   MAY also provide support for the Transport Security Model (TSM)
   [RFC5591] in combination with a secure transport such as SSH
   [RFC5592] or TLS/DTLS [RFC6353].

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED.  Instead, it is RECOMMENDED to deploy SNMPv3 and to



Herberg, et al.         Expires December 14, 2013              [Page 78]

Internet-Draft               The OLSRv2-MIB                    June 2013


   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module is properly configured to give access to
   the objects only to those principals (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.

9.  Applicability Statement

   This document describes objects for configuring parameters of the
   Optimized Link State Routing version 2 (OLSRv2) Protocol [OLSRv2]
   process on a router.  This MIB module, denoted OLSRv2-MIB, also
   reports state, performance information and notifications.  The OLSRv2
   protocol relies upon information gathered via the Neighborhood
   Discovery Protocol [RFC6130] in order to perform its operations.  The
   NHDP protocol is managed via the NHDP-MIB [RFC6779].

   MANET deployments can greatly differ in aspects of dynamics of the
   topology, capacity and loss rates of underlying channels, traffic
   flow directions, memory and CPU capacity of routers etc.  SNMP and
   therefore this MIB module are only applicable for a subset of MANET
   deployments, in particular deployments:

   o  In which routers have enough memory and CPU resources to run SNMP
      and expose the MIB module.

   o  Where a network management station (NMS) is defined to which
      notifications are generated, and from which routers can be
      managed.

   o  Where this NMS is reachable from routers in the MANET most of the
      time (as notifications to the NMS and management information from
      the NMS to the router will be lost when connectivity is
      temporarily lost).  This requires that the topology of the MANET
      is only moderately dynamic.

   o  Where the underlying wireless channel supports enough bandwidth to
      run SNMP, and where loss rates of the channel are not exhaustive.

   Certain MANET deployments, such as community networks with non-mobile
   routers, dynamic topology because of changing link quality, and a
   pre-defined gateway (that could also serve as NMS), are examples of
   networks applicable for this MIB module.  Other, more constrained
   deployments of MANETs may not be able to run SNMP and require
   different management protocols.

   Some level of configuration, i.e., read-write objects, is desirable
   for OLSRv2 deployments.  Topology related configuration such as the
   ability to enable OLSRv2 on new interfaces or initially configure



Herberg, et al.         Expires December 14, 2013              [Page 79]

Internet-Draft               The OLSRv2-MIB                    June 2013


   OLSRv2 on a router's interfaces through the
   olsrv2InterfaceAdminStatus object is critical to initial system
   startup.  The OLSRv2 protocol allows for some level of performance
   tuning through various protocol parameters and this MIB module allows
   for configuration of those protocol parameters through read-write
   objects such as the olsrv2TcHopLimit or the olsrv2FMaxJitter.  Other
   read-write objects allow for the control of Notification behavior
   through this MIB module, e.g., the
   olsrv2RoutingSetRecalculationCountThreshold object.  A fuller
   discussion of MANET network management applicability is to be
   provided elsewhere [USE-CASES].

10.  IANA Considerations

   The MIB module in this document uses the following IANA-assigned
   OBJECT IDENTIFIER value recorded in the SMI Numbers registry:

         Descriptor        OBJECT IDENTIFIER value
         ----------        -----------------------
         OLSRv2-MIB          { mib-2 ZZZZ }
         IANA EDITOR NOTE: please assign ZZZZ

11.  Acknowledgements

   The authors would like to thank Randy Presuhn, Benoit Claise, Adrian
   Farrel, as well as the entire MANET WG for reviews of this document.

   This MIB document uses the template authored by D. Harrington which
   is based on contributions from the MIB Doctors, especially Juergen
   Schoenwaelder, Dave Perkins, C.M.Heard and Randy Presuhn.

12.  References

12.1.  Normative References

   [OLSRv2]      Clausen, T., Dearlove, C., Jacquet, P., and U. Herberg,
                 "The Optimized Link State Routing Protocol version 2",
                 draft-ietf-manet-olsrv2-19 (work in progress),
                 March 2013.

   [RFC2119]     Bradner, S., "Key words for use in RFCs to Indicate
                 Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2578]     McCloghrie, K., Ed., Perkins, D., Ed., and J.
                 Schoenwaelder, Ed., "Structure of Management
                 Information Version 2 (SMIv2)", STD 58, RFC 2578,
                 April 1999.




Herberg, et al.         Expires December 14, 2013              [Page 80]

Internet-Draft               The OLSRv2-MIB                    June 2013


   [RFC2579]     McCloghrie, K., Ed., Perkins, D., Ed., and J.
                 Schoenwaelder, Ed., "Textual Conventions for SMIv2",
                 STD 58, RFC 2579, April 1999.

   [RFC2580]     McCloghrie, K., Perkins, D., and J. Schoenwaelder,
                 "Conformance Statements for SMIv2", STD 58, RFC 2580,
                 April 1999.

   [RFC2863]     McCloghrie, K. and F. Kastenholz, "The Interfaces Group
                 MIB", RFC 2863, June 2000.

   [RFC3414]     Blumenthal, U. and B. Wijnen, "User-based Security
                 Model (USM) for version 3 of the Simple Network
                 Management Protocol (SNMPv3)", December 2002.

   [RFC3418]     Presuhn, R., "Management Information Base (MIB) for the
                 Simple Network Management Protocol (SNMP)", STD 62,
                 RFC 3418, December 2002.

   [RFC3826]     Blumenthal, U., Maino, F., and K. McCloghrie, "The
                 Advanced Encryption Standard (AES) Cipher  Algorithm in
                 the SNMP User-based Security Model", June 2004.

   [RFC4001]     Daniele, M., Haberman, B., Routhier, S., and J.
                 Schoenwaelder, "Textual Conventions for Internet
                 Network Addresses", RFC 4001, February 2005.

   [RFC5591]     Harrington, D. and W. Hardaker, "Transport Security
                 Model for the Simple Network  Management Protocol
                 (SNMP)", June 2009.

   [RFC5592]     Harrington, D., Saloway, J., and W. Hardaker, "Secure
                 Shell Transport Model for the Simple Network
                 Management Protocol (SNMP)", June 2009.

   [RFC6130]     Clausen, T., Dearlove, C., and J. Dean, "Mobile Ad Hoc
                 Network (MANET) Neighborhood Discovery Protocol
                 (NHDP)", RFC 6130, April 2011.

   [RFC6353]     Hardaker, W., "Transport Layer Security (TLS) Transport
                 Model for the Simple Network Management Protocol
                 (SNMP)", July 2011.

   [RFC6779]     Herberg, U., Cole, R., and I. Chakeres, "Definition of
                 Managed Objects for the Neighborhood Discovery
                 Protocol", RFC 6779, May 2012.





Herberg, et al.         Expires December 14, 2013              [Page 81]

Internet-Draft               The OLSRv2-MIB                    June 2013


12.2.  Informative References

   [RFC3410]     Case, J., Mundy, R., Partain, D., and B. Stewart,
                 "Introduction and Applicability Statements for
                 Internet-Standard Management Framework", RFC 3410,
                 December 2002.

   [REPORT-MIB]  Cole, R., Macker, J., and A. Bierman, "Definition of
                 Managed Objects for Performance Reporting",
                 draft-ietf-manet-report-mib-03 (work in progress),
                 November 2012.

   [USE-CASES]   Nguyen, J., Cole, R., Herberg, U., Yi, J., and J. Dean,
                 "Network Management of Mobile Ad hoc Networks (MANET):
                 Architecture, Use Cases, and Applicability",
                 draft-nguyen-manet-management-00 (work in progress),
                 February 2013.

Appendix A.  Appendix A:

   This appendix contains the IANAolsrv2LinkMetricType-MIB module
   defined by this specification below.  The RFC editor should remove
   this specification of the IANAolsrv2LinkMetricType-MIB upon
   publication of the OLSRv2-MIB.  Further, IANA should take over the
   IANAolsrv2LinkMetricType-MIB and to keep it synchronized with the
   registry identified below within the IANAolsrv2LinkMetricType
   TEXTUAL-CONVENTION.


      IANAolsrv2LinkMetricType-MIB DEFINITIONS ::= BEGIN

      IMPORTS
          MODULE-IDENTITY, mib-2
                    FROM SNMPv2-SMI
          TEXTUAL-CONVENTION
                    FROM SNMPv2-TC;

      ianaolsrv2LinkMetricType MODULE-IDENTITY
          LAST-UPDATED "201306110000Z"  -- June 11, 2013
          ORGANIZATION "IANA"
          CONTACT-INFO "Internet Assigned Numbers Authority

                        Postal: ICANN
                                4676 Admiralty Way, Suite 330
                                Marina del Rey, CA 90292

                        Tel:    +1 310 823 9358
                        E-Mail: iana@iana.org"



Herberg, et al.         Expires December 14, 2013              [Page 82]

Internet-Draft               The OLSRv2-MIB                    June 2013


          DESCRIPTION  "This MIB module defines the
                        IANAolsrv2LinkMetricType Textual
                        Convention, and thus the enumerated values of
                        the olsrv2LinkMetricType object defined in
                        the OLSRv2-MIB."
          REVISION     "201306110000Z"  -- June 11, 2013
          DESCRIPTION  "Initial version of this MIB as published in
                        RFC KKKK."

          ::= { mib-2 kkkk }

   IANAolsrv2LinkMetricTypeTC ::= TEXTUAL-CONVENTION
      STATUS      current
      DESCRIPTION
         "This data type is used as the syntax of the
          olsrv2LinkMetricType object in the definition
          of the OLSRv2-MIB module.

          The olsrv2LinkMetricType corresponds to
          LINK_METRIC_TYPE of OLSRv2 (RFC XXXX).
          OLSRv2 uses bidirectional additive link metrics
          to determine shortest distance routes (i.e.,
          routes with smallest total of link metric values).

          OLSRv2 has established a registry for the LINK_METRIC_TYPEs
          (denoted 'LINK_METRIC Address Block TLV Type Extensions'):
                 http://www.iana.org/assignments/manet-parameters/
                      manet-parameters.xml#
                      link-metric-address-block-tlv-type-extension

          This is done in Section 24.5 in OLSRv2 (RFC XXXX).
          The LINK_METRIC_TYPE (which has as corresponding
          object in the MIB module olsrv2LinkMetricType)
          corresponds to the type extension of
          the LINK_METRIC TLV that is set up in the
          'LINK_METRIC Address Block TLV Type Extensions' registry.
          Whenever new link metric types are added to that registry,
          IANA MUST update this textual convention accordingly.

          The definition of this textual convention with the
          addition of newly assigned values is published
          periodically by the IANA, in either the Assigned
          Numbers RFC, or some derivative of it specific to
          Internet Network Management number assignments.  (The
          latest arrangements can be obtained by contacting the
          IANA.)

          Requests for new values should be made to IANA via



Herberg, et al.         Expires December 14, 2013              [Page 83]

Internet-Draft               The OLSRv2-MIB                    June 2013


          email (iana@iana.org)."
      SYNTAX  INTEGER {
                 unknown(0)     -- Link metric meaning assigned
                                --       by administrative action
                                -- 1-223 Unassigned
                                -- 224-255 Reserved for
                                --       Experimental Use
      }

      END

Appendix B.  Note to the RFC Editor


   ***************************************************************
   * Note to the RFC Editor (to be removed prior to publication) *
   *                                                             *
   * 1) The reference to RFCYYYY within the DESCRIPTION clauses  *
   * of the MIB module point to this draft and are to be         *
   * assigned by the RFC Editor.                                 *
   *                                                             *
   * 2) The reference to RFCXXXX throughout this document point  *
   * to the current draft-ietf-manet-olsrv2-xx.txt.  This        *
   * needs to be replaced with the XXXX RFC number for the       *
   * OLSRv2 publication.                                         *
   *                                                             *
   * 3) Appendix A contains the IANAolsrv2LinkMetricType-MIB     *
   * module which is defined by this specification in the        *
   * appendix.  The RFC editor should remove this specification  *
   * of the IANAolsrv2LinkMetricType-MIB upon publication of     *
   * the OLSRv2-MIB.  Further, IANA should take over the         *
   * IANAolsrv2LinkMetricType-MIB and keep it synchronized       *
   * with the registry identified within the contained           *
   * IANAolsrv2LinkMetricType TEXTUAL-CONVENTION.                *
   *                                                             *
   ***************************************************************

Authors' Addresses

   Ulrich Herberg
   Fujitsu Laboratories of America
   1240 East Arques Avenue
   Sunnyvale, CA  94085
   USA

   EMail: ulrich@herberg.name
   URI:   http://www.herberg.name/




Herberg, et al.         Expires December 14, 2013              [Page 84]

Internet-Draft               The OLSRv2-MIB                    June 2013


   Robert G. Cole
   US Army CERDEC
   6010 Frankford Road, Bldg 6010
   Aberdeen Proving Ground, Maryland  21005
   USA

   Phone: +1 443 395 8744
   EMail: robert.g.cole@us.army.mil
   URI:   http://www.cs.jhu.edu/~rgcole/


   Thomas Heide Clausen
   LIX, Ecole Polytechnique
   Palaiseau Cedex,   91128
   France

   Phone: +33 6 6058 9349
   EMail: T.Clausen@computer.org
   URI:   http://www.ThomasClausen.org/
































Herberg, et al.         Expires December 14, 2013              [Page 85]


Html markup produced by rfcmarkup 1.109, available from https://tools.ietf.org/tools/rfcmarkup/