[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 RFC 3813

Network Working Group                               Cheenu Srinivasan
Internet Draft                                         Bloomberg L.P.
Expires: March 2004
                                                     Arun Viswanathan
                                               Force10 Networks, Inc.

                                                     Thomas D. Nadeau
                                                  Cisco Systems, Inc.

                                                          August 2003


       Multiprotocol Label Switching (MPLS) Label Switching
             Router (LSR) Management Information Base

                   draft-ietf-mpls-lsr-mib-12.txt


Status of this Memo

   This document is an Internet-Draft and is in full conformance with
   all provisions of Section 10 of RFC 2026.

   Internet-Drafts are working documents of the In ternet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six
   months and may be updated, replaced, or obsoleted by other
   documents at any time.  It is inappropriate to use Internet-
   Drafts as reference material or to cite them other than as "work
   in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.


Abstract

   This memo defines an portion of the Management
   Information Base (MIB) for use with network management protocols
   in the Internet community.  In particular, it describes managed
   objects to configure and/or monitor a Multi-Protocol Label
   Switching (MPLS) Label Switching Router (LSR).

Table of Contents

        Abstract .................................................1
  1.    Introduction .............................................2
  2.    Terminology ..............................................2



MPLS Working Group             Expires March 2004            [Page 1]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



  3.    The SNMP Management Framework ............................3
  4.    Outline ..................................................3
  4.1   Summary of LSR MIB Module ................................3
  5.    Brief Description of MIB Module Objects ..................4
  5.1.  mplsInterfaceTable .......................................4
  5.2.  mplsInterfacePerfTable ...................................4
  5.3.  mplsInSegmentTable .......................................4
  5.4.  mplsInSegmentPerfTable ...................................5
  5.5.  mplsOutSegmentTable ......................................5
  5.6.  mplsOutSegmentPerfTable ..................................5
  5.7.  mplsXCTable ..............................................5
  5.8.  mplsLabelStackTable ......................................6
  5.9   mplsInSegmentMapTable ....................................6
  6.    Use of 32-bit and 64-bit Counters ........................6
  7.    Example of LSP Setup .....................................6
  8.    Application of the Interface Group to MPLS ...............8
  8.1.  Support of the MPLS Layer by ifTable .....................8
  9.    The Use of RowPointer ....................................10
  10.   MPLS Label Switching Router MIB Module Definitions .......10
  11.   Security Considerations ..................................52
  12.   Acknowledgments ..........................................54
  13.   IANA Considerations ......................................54
  13.1.  IANA Considerations for MPLS-LSR-STD-MIB ................54
  14.   References ...............................................54
  14.1. Normative References  ....................................54
  14.2. Informative References  ..................................56
  15. Authors' Addresses .........................................56
  16. Full Copyright Statement ...................................56
  17. Intellectual Property Notice ...............................57

1. Introduction

   This memo defines an portion of the Management
   Information Base (MIB) for use with network management protocols
   in the Internet community.  In particular, it describes managed
   objects for modeling a Multi-Protocol Label Switching (MPLS)
   [RFC3031] Label Switching Router (LSR).

   Comments should be made directly to the MPLS mailing list at
   mpls@uu.net.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
   NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED",  "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   RFC 2119, reference [RFC2119].

2. Terminology

   This document uses terminology from the document describing the
   MPLS architecture [RFC3031].  A label switched path (LSP) is



MPLS Working Group             Expires March 2004            [Page 2]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   modeled as a connection consisting of one or more incoming
   segments (in-segments) and/or one or more outgoing segments (out-
   segments) at a LSR.  The association or interconnection
   of the in-segments and out-segments is accomplished by
   using a cross-connect.  We use the terminology
   "connection" and "LSP" interchangeably where the meaning is clear
   from the context.

   in-segment     This is analagous to an MPLS label.
   out-segment    This is analagous to an MPLS label.
   cross-connect  This describes the conceptual connection
                  between a set of in-segments and out-segments.
                  Note that either set may be 0; that is, a
                  cross-connect may connect only out-segments
                  together with no in-segments in the case
                  where an LSP is originating on an LSR.

3. The SNMP Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI).  This memo specifies a MIB
   module that is compliant to the SMIv2, which is described in STD 58,
   RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
   [RFC2580].

4. Outline

   Configuring LSPs through an LSR involves the following steps:

   -  Enabling MPLS on MPLS capable interfaces.

   -  Configuring in-segments and out-segments.

   -  Setting up the cross-connect table to associate segments and/or
      to indicate connection origination and termination.

   -  Optionally specifying label stack actions.

   -  Optionally specifying segment traffic parameters.

4.1.  Summary of LSR MIB Module

   The MIB objects for performing these actions consist of the



MPLS Working Group             Expires March 2004            [Page 3]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   following tables:

   -  The interface table (mplsInterfaceTable),
      which is used for revealing the MPLS protocol on
      MPLS-capable interfaces.

   -  The in-segment (mplsInSegmentTable) and out-segment
      (mplsOutSegmentTable) tables, which are used for configuring
      LSP segments at an LSR.

   -  The cross-connect table (mplsXCTable), which is used to
      associate in and out segments together, in order to form a
      cross-connect.

   -  The label stack table (mplsLabelStackTable), which is used for
      specifying label stack operations.

   Further, the MPLS in-segment and out-segment performance tables,
   mplsInSegmentPerfTable and mplsOutSegmentPerfTable, contain the
   objects necessary to measure the performance of LSPs, and
   mplsInterfacePerfTable has objects to measure MPLS performance on
   a per-interface basis.

   These tables are described in the subsequent sections.

5. Brief Description of MIB Module Objects

   Sections 5.1-5.2 describe objects pertaining to MPLS-capable
   interfaces of an LSR.  The objects described in Sections 5.3-5.8,
   were derived from the Incoming Label Map (ILM) and Next Hop Label
   Forwarding Entry (NHLFE) as specified in the MPLS architecture
   document [RFC3031]. It is appropriate to note that the in-segment,
   out-segment, and cross-connect tables were modeled after similar
   tables found in [RFC2515].

5.1.   mplsInterfaceTable

   This table represents the interfaces that are MPLS capable.  An
   LSR creates an entry in this table for every MPLS capable
   interface on that LSR.

5.2.  mplsInterfacePerfTable

   This table contains objects to measure the MPLS performance of
   MPLS capable interfaces and is an AUGMENT to
   mplsInterfaceTable.

5.3.  mplsInSegmentTable

   This table contains a description of the incoming MPLS segments



MPLS Working Group             Expires March 2004            [Page 4]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   to an LSR and their associated parameters. This index for this
   table is mplsInSegmentIndex. The index structure of this
   table is specifically designed to handle many different
   MPLS implementations that manage their labels both in a
   distributed and centralized manner.

   The table is designed to handle existing MPLS labels as
   well as future label strategies that may require labels
   longer than the ones defined in RFC3031.  In these cases,
   the object mplsInSegmentLabelPtr may be used indicate
   the first accessible object in a separate table that can be
   used to represent the label because it is too long to
   be represented in a single 32-bit value (mplsInSegmentLabel).

5.4.  mplsInSegmentPerfTable

   The MPLS in-Segment Performance Table has objects to measure
   the performance of an incoming segment configured on an LSR.  It
   is an AUGMENT to mplsInSegmentTable.  High capacity counters are
   provided for objects that are likely to wrap around quickly on
   high-speed interfaces.

5.5.  mplsOutSegmentTable

   The out-Segment Table contains a description of the outgoing MPLS
   segments at an LSR and their associated parameters.

5.6.  mplsOutSegmentPerfTable

   The MPLS out-Segment Table contains objects to measure the
   performance of an outgoing segment configured on an LSR.  It is
   an AUGMENT to mplsOutSegmentTable.  High capacity counters are
   provided for objects that are likely to wrap around quickly on
   high-speed interfaces.

5.7.  mplsXCTable

   The mplsXCTable specifies information for associating segments
   together in order to instruct the LSR to switch between the
   specified segments.  It supports point-to-point, point-to-multi-
   point and multi-point-to-point connections.

   The operational status object indicates the packet forwarding
   state of a cross-connect entry. For example, when the operational
   status objects is 'down' it indicates that the specified cross-
   connect entry will not forward packets.  Likewise, when it is set
   to 'up' it indicates that packets will be forwarded.

   The administrative status object indicates the forwarding state
   desired by the operator.



MPLS Working Group             Expires March 2004            [Page 5]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003




5.8.  mplsLabelStackTable

   The mplsLabelStackTable specifies the label stack to be pushed
   onto a packet, beneath the top label.  Entries to this table are
   referred to from mplsXCTable.

5.9   mplsInSegmentMapTable

   The mplsInSegmentMapTable specifies the mapping from the
   mplsInSegmentIndex to the corresponding mplsInSegmentInterface
   and mplsInSegmentLabel objects. The purpose of this table is
   to provide the manager with an alternative means by which to
   locate in-segments.  For instance, this table can be useful
   when tracing LSPs from LSR to LSR by first following the
   in-segment to out-segment, retrieving the outgoing label
   and out-going interface, and then proceeding to interrogate
   this table at the next-hop LSR to continue the trace.

6. Use of 32-bit and 64-bit Counters

   64-bit counters are provided in this MIB module for high speed
   interfaces where the use of 32-bit counters might be impractical.
   The requirements on the use of 32-bit and 64-bit counters (copied
   verbatim from [RFC2863]) are as follows.

   For interfaces that operate at 20,000,000 (20 million) bits per
   second or less, 32-bit byte and packet counters MUST be supported.
   For interfaces that operate faster than 20,000,000 bits/second,
   and slower than 650,000,000 bits/second, 32-bit packet counters
   MUST be supported and 64-bit octet counters MUST be supported.
   For interfaces that operate at 650,000,000 bits/second or faster,
   64-bit packet counters AND 64-bit octet counters MUST be
   supported.

7. Example of LSP Setup

   In this section we provide a brief example of setting up an LSP
   using this MIB module's objects.  While this example
   is not meant to illustrate every nuance of the MIB module, it
   is intended as an aid to understanding some of the key concepts.
   It is meant to be read after going through the MIB module itself.

   Suppose that one would like to manually create a best-effort,
   unidirectional LSP.  Assume that the LSP enters the LSR via MPLS
   interface A with ifIndex 12 and exits the LSR via MPLS interface B
   with ifIndex 13.  Let us assume that we do not wish to impose any
   additional label stack beneath the top label on the outgoing
   labeled packets. The following example illustrates which rows and
   corresponding objects might be created to accomplish this. Those



MPLS Working Group             Expires March 2004            [Page 6]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   objects relevant to illustrating the relationships amongst
   different tables are shown here. Other objects may be needed
   before conceptual row activation can happen.

   The RowStatus values shown in this section are those to be used in
   the set request, typically createAndGo(4) which is used to create
   the conceptual row and have its status immediately set to active.
   Note that the proper use of createAndGo(4) requires that all
   columns that do not have a DEFVAL to be specified in order for
   the SET to succeed. In the example below we have not specify all
   such columns for the sake of keeping the example short. Please
   keep in mind that all such fields must be send during a real SET
   operation.  A subsequent retrieval operation on the conceptual
   row will return a different value, such as active(1). Please see
   [RFC2579] for a detailed discussion on the use of RowStatus.

   We first create a cross-connect entry that associates the
   desired segments together.

   In mplsXCTable:
   {
      mplsXCIndex                = 0x02,
      mplsXCInSegmentIndex       = 0x00000015,
      mplsXCOutSegmentIndex      = 0x01,

      mplsXCLspId                = 0x0102 -- unique ID
      mplsXCLabelStackIndex      = 0x00, -- only a single
                                         -- outgoing label
      mplsXCRowStatus            = createAndGo(4)
   }

   Next, we create the appropriate in-segment and out-segment
   entries based on the cross-connect. Note that some agents
   may wish to automatically create the in and out-segments
   based on the cross-connect creation.


   In mplsInSegmentTable:
   {
      mplsInSegmentIndex              = 0x00000015

      mplsInSegmentLabel              = 21, -- incoming label
      mplsInSegmentNPop               = 1,
      mplsInSegmentInterface          = 12, -- incoming interface

      -- RowPointer MUST point to the first accesible column.
      mplsInSegmentLabelPtr           = 0.0,
      mplsInSegmentTrafficParamPtr    = 0.0,

      mplsInSegmentRowStatus          = createAndGo(4)



MPLS Working Group             Expires March 2004            [Page 7]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   }

   In mplsOutSegmentTable:
   {
      mplsOutSegmentIndex             = 0x01,
      mplsOutSegmentInterface         = 13, -- outgoing interface
      mplsOutSegmentPushTopLabel      = true(1),
      mplsOutSegmentTopLabel          = 22, -- outgoing label

      -- RowPointer MUST point to the first accesible column.
      mplsOutSegmentTrafficParamPtr   = 0.0,
      mplsOutSegmentLabelPtr          = 0.0,

      mplsOutSegmentRowStatus         = createAndGo(4)
   }

   Note that the mplsInSegmentXCIndex and mplsOutSegmentXCIndex
   objects will automatically be populated with the string 0x02
   when these segments are referred to from the corresponding
   cross- connect entry.

8. Application of the Interface Group to MPLS

   RFC2863 defines generic managed objects for managing
   interfaces.  This memo contains the media-specific
   extensions to the Interfaces Group for managing MPLS interfaces.

   This memo assumes the interpretation of the Interfaces Group to be
   in accordance with [RFC2863] which states that the interfaces
   table (ifTable) contains information on the managed resource's
   interfaces and that each sub-layer below the internetwork layer of
   a network interface is considered an interface.  Thus, the MPLS
   interface is represented as an entry in the ifTable.  The inter-
   relation of entries in the ifTable is defined by Interfaces Stack
   Group defined in [RFC2863].

   When using MPLS interfaces, the interface stack table might appear
   as follows:

      +----------------------------------------+
      |   MPLS interface; ifType = mpls(166)   +
      +----------------------------------------+
      |            Underlying Layer            +
      +----------------------------------------+

   In the above diagram, "Underlying Layer" refers to the ifIndex of
   any interface type for which MPLS interworking has been defined.
   Examples include ATM, Frame Relay, Ethernet, etc.

8.1.  Support of the MPLS Layer by ifTable



MPLS Working Group             Expires March 2004            [Page 8]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003




   Some specific interpretations of ifTable for the MPLS layer
   follow.

   Object        Use for the MPLS layer

   ifIndex       Each MPLS interface is represented by an ifEntry.

   ifDescr       Description of the MPLS interface.

   ifType        The value that is allocated for MPLS is 166.

   ifSpeed       The total bandwidth in bits per second for use by
                 the MPLS layer.

   ifPhysAddress Unused.

   ifAdminStatus This variable indicates the administrator's intent
                 as to whether MPLS should be enabled, disabled, or
                 running in some diagnostic testing mode on this
                 interface.  Also see [RFC2863].

   ifOperStatus  This value reflects the actual operational status
                 of MPLS on this interface.

   ifLastChange  See [RFC2863].

   ifInOctets    The number of received octets over the interface,
                 i.e., the number of received, octets received as
                 labeled packets.

   ifOutOctets   The number of transmitted octets over the
                 interface, i.e., the number of octets transmitted
                 as labeled packets.

   ifInErrors    The number of labeled packets dropped due to
                 uncorrectable errors.

   ifInUnknownProtos
                 The number of received packets discarded during
                 packet header validation, including packets with
                 unrecognized label values.

   ifOutErrors   See [RFC2863].

   ifName        Textual name (unique on this system) of the
                 interface or an octet string of zero length.

   ifLinkUpDownTrapEnable
                 Default is disabled (2).



MPLS Working Group             Expires March 2004            [Page 9]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003




   ifConnectorPresent
                 Set to false (2).

   ifHighSpeed   See [RFC2863].

   ifHCInOctets  The 64-bit version of ifInOctets; supported if
                 required by the compliance statements in [RFC2863].

   ifHCOutOctets The 64-bit version of ifOutOctets; supported if
                 required by the compliance statements in [RFC2863].

   ifAlias       The non-volatile 'alias' name for the interface as
                 specified by a network manager.

   ifCounterDiscontinuityTime
                 See [RFC2863].


9.   The Use of RowPointer

   RowPointer is a textual convention used to identify a conceptual
   row in a MIB Table by pointing to the first accessible object
   in that row. In this MIB module, the trafficParamPtr object from
   either the mplsInSegmentTable or mplsOutSegmentTable SHOULD
   indicate the first accessible column in an entry in the
   MplsTunnelResourceEntry in the MPLS-TE-STD-MIB [TEMIB]
   to indicate the traffic parameter settings for this
   segment, if it represents an LSP used for a TE tunnel.

   The trafficParamPtr object may optionally point at an
   externally defined traffic parameter specification
   table. A value of zeroDotZero indicates best-effort
   treatment. By having the same value of this object,
   two or more segments can indicate resource sharing
   of such things as LSP queue space, etc.

10.   MPLS Label Switching Router MIB Module Definitions

MPLS-LSR-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
   MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
   Integer32, Counter32, Unsigned32, Counter64, Gauge32,
   zeroDotZero
      FROM SNMPv2-SMI
   MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
      FROM SNMPv2-CONF
   TruthValue, RowStatus, StorageType, RowPointer,
   TimeStamp, TEXTUAL-CONVENTION
      FROM SNMPv2-TC



MPLS Working Group            Expires March 2004            [Page 10]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   InterfaceIndexOrZero, ifGeneralInformationGroup,
   ifCounterDiscontinuityGroup
      FROM IF-MIB
   mplsStdMIB, MplsLSPID, MplsLabel, MplsBitRate,
   MplsOwner
      FROM MPLS-TC-STD-MIB
   AddressFamilyNumbers
      FROM IANA-ADDRESS-FAMILY-NUMBERS-MIB
   InetAddress, InetAddressType
      FROM INET-ADDRESS-MIB
   ;

mplsLsrStdMIB MODULE-IDENTITY
   LAST-UPDATED "200308061200Z"  -- 06 August 2003 12:00:00 GMT
   ORGANIZATION "Multiprotocol Label Switching (MPLS) Working Group"
   CONTACT-INFO
       "        Cheenu Srinivasan
                Blomberg L.P.
        Email:  cheenu@bloomberg.net

                Arun Viswanathan
                Force10 Networks, Inc.
        Email:  arunv@force10networks.com

                Thomas D. Nadeau
                Cisco Systems, Inc.
        Email:  tnadeau@cisco.com

        Comments about this document should be emailed
        directly to the MPLS working group mailing list at
        mpls@uu.net."

   DESCRIPTION
       "This MIB module contains managed object definitions for
        the Multiprotocol Label Switching (MPLS) Router as
        defined in: Rosen, E., Viswanathan, A., and R.
        Callon, Multiprotocol Label Switching Architecture,
        RFC 3031, January 2001.

        Copyright (C) The Internet Society (2003).  This
        version of this MIB module is part of RFCXXX; see
        the RFC itself for full legal notices."

   -- Revision history.
   REVISION
       "200308061200Z" -- 06 August 2003 12:00:00 GMT
   DESCRIPTION
       "Initial revision, published as part of RFC XXXX."
   ::= { mplsStdMIB 2 }




MPLS Working Group            Expires March 2004            [Page 11]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



-- Textual Conventions

MplsIndexType ::= TEXTUAL-CONVENTION
   STATUS              current
   DESCRIPTION
       "This is an octet string that can be used as a table
        index in cases where a large addressable space is
        required such as on an LSR where many applications
        may be provisioning labels.

        Note that the string containing the single octet with
        the value 0x00 is a reserved value used to represent
        special cases. When this textual convention is used
        as the SYNTAX of an object, the DESCRITPION clause
        MUST specify if this special value is valid and if so
        what the special meaning is.

        In systems that provide write access to the MPLS-LSR-STD
        MIB, mplsIndexType SHOULD be used as a simple multi-digit
        integer encoded as an octet string.
        No further overloading of the meaning of an index SHOULD
        be made.

        In systems that do not offer write access to the MPLS-LSR-STD
        MIB, the mplsIndexType may contain implicit formatting that is
        specific to the implementation to convey additional
        information such as interface index, physical card or
        device, or application id. The interpretation of this
        additional formatting is implementation dependent and
        not covered in this document. Such formatting MUST
        NOT impact the basic functionality of read-only access
        to the MPLS-LSR-STD MIB by management applications that are
        not aware of the formatting rules."
   SYNTAX              OCTET STRING (SIZE(1..24))

MplsIndexNextType ::= TEXTUAL-CONVENTION
   STATUS              current
   DESCRIPTION
       "When a MIB module is used for configuration, an object with
        this SYNTAX always contains a legal value (a non-zero-length
        string) for an index that is not currently used in the relevant
        table. The Command Generator (Network Management Application)
        reads this variable and uses the (non-zero-length string)
        value read when creating a new row with an SNMP SET.

        When the SET is performed, the Command Responder (agent) must
        determine whether the value is indeed still unused; Two Network
        Management Applications may attempt to create a row
        (configuration entry) simultaneously and use the same value. If
        it is currently unused, the SET succeeds and the Command



MPLS Working Group            Expires March 2004            [Page 12]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



        Responder (agent) changes the value of this object, according
        to an implementation-specific algorithm.  If the value is in
        use, however, the SET fails.  The Network Management
        Application must then re-read this variable to obtain a new
        usable value.

        Note that the string containing the single octet with
        the value 0x00 is a reserved value used to represent
        the special case where no additional indexes can be
        provisioned, or in systems that do not offer
        write access, objects defined using this textual
        convention MUST return the string containing the single
        octet with the value 0x00."
   SYNTAX              OCTET STRING (SIZE(1..24))

-- Top level components of this MIB module.

-- Notifications
mplsLsrNotifications OBJECT IDENTIFIER ::= { mplsLsrStdMIB 0 }

-- Tables, Scalars
mplsLsrObjects       OBJECT IDENTIFIER ::= { mplsLsrStdMIB 1 }

-- Conformance
mplsLsrConformance   OBJECT IDENTIFIER ::= { mplsLsrStdMIB 2 }

-- MPLS Interface Table.
mplsInterfaceTable  OBJECT-TYPE
   SYNTAX        SEQUENCE OF MplsInterfaceEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies per-interface MPLS capability
        and associated information."
   ::= { mplsLsrObjects 1 }

mplsInterfaceEntry OBJECT-TYPE
   SYNTAX        MplsInterfaceEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "A conceptual row in this table is created
        automatically by an LSR for every interface capable
        of supporting MPLS and which is configured to do so.
        A conceptual row in this table will exist iff a
        corresponding entry in ifTable exists with ifType =
        mpls(166). If this associated entry in ifTable is
        operationally disabled (thus removing MPLS
        capabilities on that interface), the corresponding
        entry in this table MUST be deleted shortly thereafter.



MPLS Working Group            Expires March 2004            [Page 13]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



        An conceptual row with index 0 is created if the LSR
        supports per-platform labels. This conceptual row
        represents the per-platform label space and contains
        parameters that apply to all interfaces that participate
        in the per-platform label space. Other conceptual rows
        in this table represent MPLS interfaces that may
        participate in either the per-platform or per-
        interface label spaces, or both.  Implementations
        that either only support per-platform labels,
        or have only them configured, may choose to return
        just the mplsInterfaceEntry of 0 and not return
        the other rows. This will greatly reduce the numebr
        of objects returned. Further information about label
        space participation of an interface is provided in
        the DESCRIPTION clause of
        mplsInterfaceLabelParticipationType."
   INDEX { mplsInterfaceIndex }
   ::= { mplsInterfaceTable 1 }

MplsInterfaceEntry ::= SEQUENCE {
  mplsInterfaceIndex                  InterfaceIndexOrZero,
  mplsInterfaceLabelMinIn             MplsLabel,
  mplsInterfaceLabelMaxIn             MplsLabel,
  mplsInterfaceLabelMinOut            MplsLabel,
  mplsInterfaceLabelMaxOut            MplsLabel,
  mplsInterfaceTotalBandwidth         MplsBitRate,
  mplsInterfaceAvailableBandwidth     MplsBitRate,
  mplsInterfaceLabelParticipationType BITS
}

mplsInterfaceIndex OBJECT-TYPE
   SYNTAX        InterfaceIndexOrZero
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This is a unique index for an entry in the
        MplsInterfaceTable.  A non-zero index for an
        entry indicates the ifIndex for the corresponding
        interface entry of the MPLS-layer in the ifTable.
        The entry with index 0 represents the per-platform
        label space and contains parameters that apply to all
        interfaces that participate in the per-platform label
        space. Other entries defined in this table represent
        additional MPLS interfaces that may participate in either
        the per-platform or per-interface label spaces, or both."
   REFERENCE
       "RFC 2863 - The Interfaces Group MIB, McCloghrie, K.,
        and F. Kastenholtz, June 2000"
   ::= { mplsInterfaceEntry 1 }




MPLS Working Group            Expires March 2004            [Page 14]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



mplsInterfaceLabelMinIn OBJECT-TYPE
   SYNTAX        MplsLabel
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This is the minimum value of an MPLS label that this
        LSR is willing to receive on this interface."
   ::= { mplsInterfaceEntry 2 }

mplsInterfaceLabelMaxIn OBJECT-TYPE
   SYNTAX        MplsLabel
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This is the maximum value of an MPLS label that this
        LSR is willing to receive on this interface."
   ::= { mplsInterfaceEntry 3 }

mplsInterfaceLabelMinOut OBJECT-TYPE
   SYNTAX        MplsLabel
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This is the minimum value of an MPLS label that this
        LSR is willing to send on this interface."
   ::= { mplsInterfaceEntry 4 }

mplsInterfaceLabelMaxOut OBJECT-TYPE
   SYNTAX        MplsLabel
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This is the maximum value of an MPLS label that this
        LSR is willing to send on this interface."
   ::= { mplsInterfaceEntry 5 }

mplsInterfaceTotalBandwidth OBJECT-TYPE
   SYNTAX        MplsBitRate
   UNITS         "kilobits per second"
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This value indicates the total amount of usable
        bandwidth on this interface and is specified in
        kilobits per second (Kbps).  This variable is not
        applicable when applied to the interface with index
        0. When this value cannot be measured, this value
        should contain the nominal bandwidth."
::= { mplsInterfaceEntry 6 }




MPLS Working Group            Expires March 2004            [Page 15]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



mplsInterfaceAvailableBandwidth OBJECT-TYPE
   SYNTAX        MplsBitRate
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This value indicates the total amount of available
        bandwidth available on this interface and is
        specified in kilobits per second (Kbps).  This value
        is calculated as the difference between the amount
        of bandwidth currently in use and that specified in
        mplsInterfaceTotalBandwidth.  This variable is not
        applicable when applied to the interface with index
        0. When this value cannot be measured, this value
        should contain the nominal bandwidth."
::= { mplsInterfaceEntry 7 }

mplsInterfaceLabelParticipationType OBJECT-TYPE
   SYNTAX  BITS {
                  perPlatform (0),
                  perInterface (1)
              }
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "If the value of the mplsInterfaceIndex for this
        entry is zero, then this entry corresponds to the
        per-platform label space for all interfaces configured
        to use that label space. In this case the perPlatform(0)
        bit MUST be set; the perInterface(1) bit is meaningless
        and MUST be ignored.

        The remainder of this description applies to entries
        with a non-zero value of mplsInterfaceIndex.

        If the perInterface(1) bit is set then the value of
        mplsInterfaceLabelMinIn, mplsInterfaceLabelMaxIn,
        mplsInterfaceLabelMinOut, and
        mplsInterfaceLabelMaxOut for this entry reflect the
        label ranges for this interface.

        If only the perPlatform(0) bit is set, then the value of
        mplsInterfaceLabelMinIn, mplsInterfaceLabelMaxIn,
        mplsInterfaceLabelMinOut, and
        mplsInterfaceLabelMaxOut for this entry MUST be
        identical to the instance of these objects with
        index 0.  These objects may only vary from the entry
        with index 0 if both the perPlatform(0) and perInterface(1)
        bits are set.

        In all cases, at a minimum one of the perPlatform(0) or



MPLS Working Group            Expires March 2004            [Page 16]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



        perInterface(1) bits MUST be set to indicate that
        at least one label space is in use by this interface. In
        all cases, agents MUST ensure that label ranges are
        specified consistently and MUST return an
        inconsistentValue error when they do not."
   REFERENCE
       "Rosen, E., Viswanathan, A., and R. Callon,
        Multiprotocol Label Switching Architecture, RFC
        3031, January 2001."
::= { mplsInterfaceEntry 8 }

-- End of mplsInterfaceTable


-- MPLS Interface Performance Table.

mplsInterfacePerfTable  OBJECT-TYPE
   SYNTAX        SEQUENCE OF MplsInterfacePerfEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table provides MPLS performance information on
        a per-interface basis."
   ::= { mplsLsrObjects 2 }

mplsInterfacePerfEntry OBJECT-TYPE
   SYNTAX        MplsInterfacePerfEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table is created by the LSR for
        every interface capable of supporting MPLS.  Its is
        an extension to the mplsInterfaceEntry table.
        Note that the discontinuity behavior of entries in
        this table MUST be based on the corresponding
        ifEntry's ifDiscontinuityTime."
   AUGMENTS      { mplsInterfaceEntry }
      ::= { mplsInterfacePerfTable 1 }

MplsInterfacePerfEntry ::= SEQUENCE {
      -- incoming direction
      mplsInterfacePerfInLabelsInUse         Gauge32,
      mplsInterfacePerfInLabelLookupFailures Counter32,

      -- outgoing direction
      mplsInterfacePerfOutLabelsInUse      Gauge32,
      mplsInterfacePerfOutFragmentedPkts   Counter32
   }

mplsInterfacePerfInLabelsInUse OBJECT-TYPE



MPLS Working Group            Expires March 2004            [Page 17]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   SYNTAX        Gauge32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of labels that are in
        use at this point in time on this interface in the
        incoming direction. If the interface participates in
        only the per-platform label space, then the value of
        the instance of this object MUST be identical to
        the value of the instance with index 0. If the
        interface participates in the per-interface label
        space, then the instance of this object MUST
        represent the number of of per-interface labels that
        are in use on this interface."
   ::= { mplsInterfacePerfEntry 1 }

mplsInterfacePerfInLabelLookupFailures  OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of labeled packets
        that have been received on this interface and which
        were discarded because there was no matching cross-
        connect entry. This object MUST count on a per-
        interface basis regardless of which label space the
        interface participates in."
   ::= { mplsInterfacePerfEntry 2 }

mplsInterfacePerfOutLabelsInUse OBJECT-TYPE
   SYNTAX        Gauge32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of top-most labels in
        the outgoing label stacks that are in use at this
        point in time on this interface. This object MUST
        count on a per-interface basis regardless of which
        label space the interface participates in."
   ::= { mplsInterfacePerfEntry 3 }

mplsInterfacePerfOutFragmentedPkts OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object counts the number of outgoing MPLS
        packets that required fragmentation before
        transmission on this interface. This object MUST
        count on a per-interface basis regardless of which



MPLS Working Group            Expires March 2004            [Page 18]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



        label space the interface participates in."
::= { mplsInterfacePerfEntry 4 }

-- mplsInterfacePerf Table end.

mplsInSegmentIndexNext OBJECT-TYPE
   SYNTAX        MplsIndexNextType
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object contains the next available value to
        be used for mplsInSegmentIndex when creating entries
        in the mplsInSegmentTable. The special value of a
        a string containing the single octet 0x00 indicates
        that no new entries can be created in this table.
        Agents not allowing managers to create entries
        in this table MUST set this object to this special
        value."
      ::= { mplsLsrObjects 3 }

-- in-segment table.
mplsInSegmentTable  OBJECT-TYPE
   SYNTAX        SEQUENCE OF MplsInSegmentEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table contains a description of the incoming MPLS
        segments (labels) to an LSR and their associated parameters.
        The index for this table is mplsInSegmentIndex.
        The index structure of this table is specifically designed
        to handle many different MPLS implementations that manage
        their labels both in a distributed and centralized manner.
        The table is also designed to handle existing MPLS labels
        as defined in RFC3031 as well as longer ones that may
        be necessary in the future.

        In cases where the label cannot fit into the
        mplsInSegmentLabel object, the mplsInSegmentLabelPtr
        will indicate this by being set to the first accessible
        colum in the appropriate extension table's row.
        In this case an additional table MUST
        be provided and MUST be indexed by at least the indexes
        used by this table. In all other cases when the label is
        represented within the mplsInSegmentLabel object, the
        mplsInSegmentLabelPtr MUST be set to 0.0. Due to the
        fact that MPLS labels may not exceed 24 bits, the
        mplsInSegmentLabelPtr object is only a provision for
        future-proofing the MIB module. Thus, the definition
        of any extension tables is beyond the scope of this
        MIB module."



MPLS Working Group            Expires March 2004            [Page 19]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



      ::= { mplsLsrObjects 4 }

mplsInSegmentEntry  OBJECT-TYPE
   SYNTAX        MplsInSegmentEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table represents one incoming
        segment as is represented in an LSR's LFIB.
        An entry can be created by a network
        administrator or an SNMP agent, or an MPLS signaling
        protocol.  The creator of the entry is denoted by
        mplsInSegmentOwner.

        The value of mplsInSegmentRowStatus cannot be active(1)
        unless the ifTable entry corresponding to
        mplsInSegmentInterface exists.  An entry in this table
        must match any incoming packets, and indicates an
        instance of mplsXCEntry based on which forwarding
        and/or switching actions are taken."
   INDEX { mplsInSegmentIndex }
   ::= { mplsInSegmentTable 1 }

MplsInSegmentEntry ::= SEQUENCE {
  mplsInSegmentIndex                MplsIndexType,
  mplsInSegmentInterface            InterfaceIndexOrZero,
  mplsInSegmentLabel                MplsLabel,
  mplsInSegmentLabelPtr             RowPointer,
  mplsInSegmentNPop                 Integer32,
  mplsInSegmentAddrFamily           AddressFamilyNumbers,
  mplsInSegmentXCIndex              MplsIndexType,
  mplsInSegmentOwner                MplsOwner ,
  mplsInSegmentTrafficParamPtr      RowPointer,
  mplsInSegmentRowStatus            RowStatus,
  mplsInSegmentStorageType          StorageType
}

mplsInSegmentIndex OBJECT-TYPE
   SYNTAX        MplsIndexType
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "The index for for this in-segment. The
        string containing the single octet 0x00
        MUST not be used as an index."
   ::= { mplsInSegmentEntry 1 }

mplsInSegmentInterface OBJECT-TYPE
   SYNTAX        InterfaceIndexOrZero
   MAX-ACCESS    read-create



MPLS Working Group            Expires March 2004            [Page 20]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   STATUS        current
   DESCRIPTION
       "This object represents the
        interface index for the incoming MPLS interface.  A
        value of zero represents all interfaces participating in
        the per-platform label space.  This may only be used
        in cases where the incoming interface and label
        are associated with the same mplsXCEntry. Specifically,
        given a label and any incoming interface pair from the
        per-platform label space, the outgoing label/interface
        mapping remains the same. If this is not the case,
        then individual entries MUST exist that
        can then be mapped to unique mplsXCEntries."
   ::= { mplsInSegmentEntry 2 }

mplsInSegmentLabel OBJECT-TYPE
   SYNTAX        MplsLabel
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
     "If the corresponding instance of mplsInSegmentLabelPtr is
      zeroDotZero then this object MUST contain the incoming label
      associated with this in-segment. If not this object SHOULD
      be zero and MUST be ignored."
   ::= { mplsInSegmentEntry 3 }

mplsInSegmentLabelPtr OBJECT-TYPE
   SYNTAX        RowPointer
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "If the label for this segment cannot be represented
        fully within the mplsInSegmentLabel object,
        this object MUST point to the first accessible
        column of a conceptual row in an external table containing
        the label.  In this case, the mplsInSegmentTopLabel
        object SHOULD be set to 0 and ignored. This object MUST
        be set to zeroDotZero otherwise."
   DEFVAL { zeroDotZero }
   ::= { mplsInSegmentEntry 4 }

mplsInSegmentNPop OBJECT-TYPE
   SYNTAX        Integer32 (1..2147483647)
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The number of labels to pop from the incoming
        packet.  Normally only the top label is popped from
        the packet and used for all switching decisions for
        that packet.  This is indicated by setting this



MPLS Working Group            Expires March 2004            [Page 21]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



        object to the default value of 1. If an LSR supports
        popping of more than one label, this object MUST
        be set to that number. This object cannot be modified
        if mplsInSegmentRowStatus is active(1)."
   DEFVAL        { 1 }
   ::= { mplsInSegmentEntry 5 }

mplsInSegmentAddrFamily OBJECT-TYPE
   SYNTAX        AddressFamilyNumbers
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The IANA address family of packets
        received on this segment, which is used at an egress
        LSR to deliver them to the appropriate layer 3 entity.
        A value of other(0) indicates that the family type is
        either unknown or undefined; this SHOULD NOT be used
        at an egress LSR. This object cannot be
        modified if mplsInSegmentRowStatus is active(1)."
   REFERENCE
       "See Internet Assigned Numbers Authority (IANA),
        ADDRESS FAMILY NUMBERS."
   DEFVAL        { other }
   ::= { mplsInSegmentEntry 6 }

mplsInSegmentXCIndex OBJECT-TYPE
   SYNTAX        MplsIndexType
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "Index into mplsXCTable which identifies which cross-
        connect entry this segment is part of.  The string
        containing the single octet 0x00 indicates that this
        entry is not referred to by any cross-connect entry.
        When a cross-connect entry is created which this
        in-segment is a part of, this object is automatically
        updated to reflect the value of mplsXCIndex of that
        cross-connect entry."
   ::= { mplsInSegmentEntry 7 }

mplsInSegmentOwner OBJECT-TYPE
   SYNTAX        MplsOwner
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "Denotes the entity that created and is responsible
        for managing this segment."
   ::= { mplsInSegmentEntry 8 }

mplsInSegmentTrafficParamPtr OBJECT-TYPE



MPLS Working Group            Expires March 2004            [Page 22]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   SYNTAX            RowPointer
   MAX-ACCESS        read-create
   STATUS            current
   DESCRIPTION
     "This variable represents a pointer to the traffic
      parameter specification for this out-segment.  This
      value may point at an entry in the
      mplsTunnelResourceTable in the MPLS-TE-STD-MIB (RFCnnnn)

      RFC Editor: Please fill in RFC number.

      to indicate which traffic parameter settings for this
      segment if it represents an LSP used for a TE tunnel.

      This value may optionally point at an
      externally defined traffic parameter specification
      table.  A value of zeroDotZero indicates best-effort
      treatment.  By having the same value of this object,
      two or more segments can indicate resource sharing
      of such things as LSP queue space, etc.

      This object cannot be modified if mplsInSegmentRowStatus
      is active(1).  For entries in this table that
      are preserved after a re-boot, the agent MUST ensure
      that their integrity be preserved, or this object should
      be set to 0.0 if it cannot."
   DEFVAL { zeroDotZero }
   ::= { mplsInSegmentEntry 9 }

mplsInSegmentRowStatus OBJECT-TYPE
   SYNTAX        RowStatus
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This variable is used to create, modify, and/or
        delete a row in this table. When a row in this
        table has a row in the active(1) state, no
        objects in this row can be modified except the
        mplsInSegmentRowStatus and mplsInSegmentStorageType."
   ::= { mplsInSegmentEntry 10 }

mplsInSegmentStorageType OBJECT-TYPE
   SYNTAX        StorageType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This variable indicates the storage type for this
        object. The agent MUST ensure that this object's
        value remains consistent with the associated
        mplsXCEntry. Conceptual rows having the value



MPLS Working Group            Expires March 2004            [Page 23]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



        'permanent' need not allow write-access to any
        columnar objects in the row."
   REFERENCE
        "See RFC2579."
   DEFVAL { volatile }
   ::= { mplsInSegmentEntry 11 }

-- End of mplsInSegmentTable

-- in-segment performance table.

mplsInSegmentPerfTable  OBJECT-TYPE
   SYNTAX        SEQUENCE OF MplsInSegmentPerfEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table contains statistical information for
        incoming MPLS segments to an LSR."
   ::= { mplsLsrObjects 5 }

mplsInSegmentPerfEntry  OBJECT-TYPE
   SYNTAX        MplsInSegmentPerfEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table contains statistical
        information about one incoming segment which is
        configured in the mplsInSegmentTable. The counters
        in this entry should behave in a manner similar to
        that of the interface.
        mplsInSegmentPerfDiscontinuityTime indicates the
        time of the last discontinuity in all of these
        objects."
   AUGMENTS  { mplsInSegmentEntry }
   ::= { mplsInSegmentPerfTable 1 }

MplsInSegmentPerfEntry ::= SEQUENCE {
    mplsInSegmentPerfOctets             Counter32,
    mplsInSegmentPerfPackets            Counter32,
    mplsInSegmentPerfErrors             Counter32,
    mplsInSegmentPerfDiscards           Counter32,

    -- high capacity counter
    mplsInSegmentPerfHCOctets           Counter64,

    mplsInSegmentPerfDiscontinuityTime  TimeStamp
   }

mplsInSegmentPerfOctets OBJECT-TYPE
   SYNTAX        Counter32



MPLS Working Group            Expires March 2004            [Page 24]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This value represents the total number of octets
        received by this segment. It MUST be equal to the
        least significant 32 bits of
        mplsInSegmentPerfHCOctets
        if mplsInSegmentPerfHCOctets is supported according to
        the rules spelled out in RFC2863."
   ::= { mplsInSegmentPerfEntry 1 }

mplsInSegmentPerfPackets OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "Total number of packets received by this segment."
   ::= { mplsInSegmentPerfEntry 2 }

mplsInSegmentPerfErrors OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "The number of errored packets received on this
        segment."
   ::= { mplsInSegmentPerfEntry 3 }

mplsInSegmentPerfDiscards OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "The number of labeled packets received on this in-
        segment, which were chosen to be discarded even
        though no errors had been detected to prevent their
        being transmitted.  One possible reason for
        discarding such a labeled packet could be to free up
        buffer space."
   ::= { mplsInSegmentPerfEntry 4 }

mplsInSegmentPerfHCOctets OBJECT-TYPE
   SYNTAX        Counter64
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "The total number of octets received.  This is the 64
        bit version of mplsInSegmentPerfOctets,
        if mplsInSegmentPerfHCOctets is supported according to
        the rules spelled out in RFC2863."



MPLS Working Group            Expires March 2004            [Page 25]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   ::= { mplsInSegmentPerfEntry 5 }

mplsInSegmentPerfDiscontinuityTime OBJECT-TYPE
   SYNTAX      TimeStamp
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
       "The value of sysUpTime on the most recent occasion
        at which any one or more of this segment's Counter32
        or Counter64 suffered a discontinuity. If no such
        discontinuities have occurred since the last re-
        initialization of the local management subsystem,
        then this object contains a zero value."
   ::= { mplsInSegmentPerfEntry 6 }

-- End of mplsInSegmentPerfTable.


-- out-segment table.

mplsOutSegmentIndexNext OBJECT-TYPE
   SYNTAX        MplsIndexNextType
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object contains the next available value to
        be used for mplsOutSegmentIndex when creating entries
        in the mplsOutSegmentTable. The special value of a
        a string containing the single octet 0x00 indicates
        indicates that no new entries can be created in this
        table. Agents not allowing managers to create entries
        in this table MUST set this object to this special
        value."
   ::= { mplsLsrObjects 6 }

mplsOutSegmentTable  OBJECT-TYPE
   SYNTAX        SEQUENCE OF MplsOutSegmentEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table contains a representation of the outgoing
        segments from an LSR."
   ::= { mplsLsrObjects 7 }

mplsOutSegmentEntry  OBJECT-TYPE
   SYNTAX        MplsOutSegmentEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table represents one outgoing



MPLS Working Group            Expires March 2004            [Page 26]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



        segment.  An entry can be created by a network
        administrator, an SNMP agent, or an MPLS signaling
        protocol.  The object mplsOutSegmentOwner indicates
        the creator of this entry. The value of
        mplsOutSegmentRowStatus cannot be active(1) unless
        the ifTable entry corresponding to
        mplsOutSegmentInterface exists.

        Note that the indexing of this table uses a single,
        arbitrary index (mplsOutSegmentIndex) to indicate
        which out-segment (i.e.: label) is being switched to
        from which in-segment (i.e: label) or in-segments.
        This is necessary because it is possible to have an
        equal-cost multi-path situation where two identical
        out-going labels are assigned to the same
        cross-connect (i.e.: they go to two different neighboring
        LSRs); thus, requiring two out-segments. In order to
        preserve the uniqueness of the references
        by the mplsXCEntry, an arbitrary integer must be used as
        the index for this table."
   INDEX { mplsOutSegmentIndex }
   ::= { mplsOutSegmentTable 1 }

MplsOutSegmentEntry ::= SEQUENCE {
  mplsOutSegmentIndex                MplsIndexType,
  mplsOutSegmentInterface            InterfaceIndexOrZero,
  mplsOutSegmentPushTopLabel         TruthValue,
  mplsOutSegmentTopLabel             MplsLabel,
  mplsOutSegmentTopLabelPtr          RowPointer,
  mplsOutSegmentNextHopAddrType    InetAddressType,
  mplsOutSegmentNextHopAddr        InetAddress,
  mplsOutSegmentXCIndex              MplsIndexType,
  mplsOutSegmentOwner                MplsOwner,
  mplsOutSegmentTrafficParamPtr      RowPointer,
  mplsOutSegmentRowStatus            RowStatus,
  mplsOutSegmentStorageType          StorageType
}

mplsOutSegmentIndex OBJECT-TYPE
   SYNTAX        MplsIndexType
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This value contains a unique index for this row.
        While a value of a string containing the single
        octet 0x00 is not valid as an index for entries
        in this table, it can be supplied as a valid value
        to index the mplsXCTable to represent entries for
        which no out-segment has been configured or
        exists."



MPLS Working Group            Expires March 2004            [Page 27]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   ::= { mplsOutSegmentEntry 1 }

mplsOutSegmentInterface OBJECT-TYPE
   SYNTAX        InterfaceIndexOrZero
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This value must contain the interface index of the
        outgoing interface. This object cannot be modified
        if mplsOutSegmentRowStatus is active(1). The
        mplsOutSegmentRowStatus cannot be set to active(1)
        until this object is set to a value corresponding to
        a valid ifEntry."
   ::= { mplsOutSegmentEntry 2 }

mplsOutSegmentPushTopLabel OBJECT-TYPE
   SYNTAX        TruthValue
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This value indicates whether or not a top label
        should be pushed onto the outgoing packet's label
        stack.  The value of this variable MUST be set to
        true(1) if the outgoing interface does not support
        pop-and-go (and no label stack remains). For example,
        on ATM interface, or if the segment represents a
        tunnel origination.  Note that it is considered
        an error in the case that mplsOutSegmentPushTopLabel
        is set to false, but the cross-connect entry which
        refers to this out-segment has a non-zero
        mplsLabelStackIndex.  The LSR MUST ensure that this
        situation does not happen. This object cannot be
        modified if mplsOutSegmentRowStatus is active(1)."
   DEFVAL { true }
   ::= { mplsOutSegmentEntry 3 }

mplsOutSegmentTopLabel OBJECT-TYPE
   SYNTAX        MplsLabel
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "If mplsOutSegmentPushTopLabel is true then this
        represents the label that should be pushed onto the
        top of the outgoing packet's label stack. Otherwise
        this value SHOULD be set to 0 by the management
        station and MUST be ignored by the agent. This
        object cannot be modified if mplsOutSegmentRowStatus
        is active(1)."
   DEFVAL { 0 }
   ::= { mplsOutSegmentEntry 4 }



MPLS Working Group            Expires March 2004            [Page 28]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003




mplsOutSegmentTopLabelPtr OBJECT-TYPE
   SYNTAX        RowPointer
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "If the label for this segment cannot be represented
        fully within the mplsOutSegmentLabel object,
        this object MUST point to the first accessible
        column of a conceptual row in an external table containing
        the label.  In this case, the mplsOutSegmentTopLabel
        object SHOULD be set to 0 and ignored. This object
        MUST be set to zeroDotZero otherwise."
   DEFVAL { zeroDotZero }
   ::= { mplsOutSegmentEntry 5 }

mplsOutSegmentNextHopAddrType OBJECT-TYPE
   SYNTAX        InetAddressType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "Indicates the next hop Internet address type.
        Only values unknown(0), ipv4(1) or ipv6(2)
        have to be supported.

        A value of unknown(0) is allowed only when
        the outgoing interface is of type point-to-point.
        If any other unsupported values are attempted in a set
        operation, the agent MUST return an inconsistentValue
        error."
   REFERENCE
       "See RFC3291."
   ::= { mplsOutSegmentEntry 6 }

mplsOutSegmentNextHopAddr OBJECT-TYPE
   SYNTAX        InetAddress
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The internet address of the next hop. The type of
        this address is determined by the value of the
        mplslOutSegmentNextHopAddrType object.

        This object cannot be modified if
        mplsOutSegmentRowStatus is active(1)."
   ::= { mplsOutSegmentEntry 7 }

mplsOutSegmentXCIndex OBJECT-TYPE
   SYNTAX        MplsIndexType
   MAX-ACCESS    read-only



MPLS Working Group            Expires March 2004            [Page 29]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   STATUS        current
   DESCRIPTION
       "Index into mplsXCTable which identifies which cross-
        connect entry this segment is part of.  A value of
        the string containing the single octet 0x00
        indicates that this entry is not referred
        to by any cross-connect entry.  When a cross-connect
        entry is created which this out-segment is a part of,
        this object MUST be updated by the agent to reflect
        the value of mplsXCIndex of that cross-connect
        entry."
   ::= { mplsOutSegmentEntry 8 }

mplsOutSegmentOwner OBJECT-TYPE
   SYNTAX        MplsOwner
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "Denotes the entity which created and is responsible
        for managing this segment."
   ::= { mplsOutSegmentEntry 9 }

mplsOutSegmentTrafficParamPtr OBJECT-TYPE
   SYNTAX        RowPointer
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
     "This variable represents a pointer to the traffic
      parameter specification for this out-segment.  This
      value may point at an entry in the
      MplsTunnelResourceEntry in the MPLS-TE-STD-MIB (RFCnnnn)

      RFC Editor: Please fill in RFC number.

      to indicate which traffic parameter settings for this
      segment if it represents an LSP used for a TE tunnel.

      This value may optionally point at an
      externally defined traffic parameter specification
      table.  A value of zeroDotZero indicates best-effort
      treatment.  By having the same value of this object,
      two or more segments can indicate resource sharing
      of such things as LSP queue space, etc.

      This object cannot be modified if
      mplsOutSegmentRowStatus is active(1).
      For entries in this table that
      are preserved after a re-boot, the agent MUST ensure
      that their integrity be preserved, or this object should
      be set to 0.0 if it cannot."



MPLS Working Group            Expires March 2004            [Page 30]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   DEFVAL { zeroDotZero }
   ::= { mplsOutSegmentEntry 10 }

mplsOutSegmentRowStatus OBJECT-TYPE
   SYNTAX        RowStatus
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "For creating, modifying, and deleting this row.
        When a row in this table has a row in the active(1)
        state, no objects in this row can be modified
        except the mplsOutSegmentRowStatus or
        mplsOutSegmentStorageType."
   ::= { mplsOutSegmentEntry 11 }

mplsOutSegmentStorageType OBJECT-TYPE
   SYNTAX        StorageType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This variable indicates the storage type for this
        object. The agent MUST ensure that this object's value
        remains consistent with the associated mplsXCEntry.
        Conceptual rows having the value 'permanent'
        need not allow write-access to any columnar
        objects in the row."
   DEFVAL { volatile }
   ::= { mplsOutSegmentEntry 12 }

-- End of mplsOutSegmentTable


-- out-segment performance table.

mplsOutSegmentPerfTable  OBJECT-TYPE
   SYNTAX        SEQUENCE OF MplsOutSegmentPerfEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table contains statistical information about
        outgoing segments from an LSR. The counters in this
        entry should behave in a manner similar to that of
        the interface."
   ::= { mplsLsrObjects 8 }

mplsOutSegmentPerfEntry  OBJECT-TYPE
   SYNTAX        MplsOutSegmentPerfEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION



MPLS Working Group            Expires March 2004            [Page 31]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



       "An entry in this table contains statistical
        information about one outgoing segment configured in
        mplsOutSegmentTable. The object
        mplsOutSegmentPerfDiscontinuityTime indicates the
        time of the last discontinuity in these objects. "
   AUGMENTS      { mplsOutSegmentEntry }
      ::= { mplsOutSegmentPerfTable 1 }

MplsOutSegmentPerfEntry ::= SEQUENCE {
      mplsOutSegmentPerfOctets             Counter32,
      mplsOutSegmentPerfPackets            Counter32,
      mplsOutSegmentPerfErrors             Counter32,
      mplsOutSegmentPerfDiscards           Counter32,

      -- HC counter
      mplsOutSegmentPerfHCOctets           Counter64,

      mplsOutSegmentPerfDiscontinuityTime  TimeStamp
   }

mplsOutSegmentPerfOctets OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This value contains the total number of octets sent
        on this segment. It MUST be equal to the least
        significant 32 bits of mplsOutSegmentPerfHCOctets
        if mplsOutSegmentPerfHCOctets is supported according to
        the rules spelled out in RFC2863."
   ::= { mplsOutSegmentPerfEntry 1 }

mplsOutSegmentPerfPackets OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This value contains the total number of packets sent
        on this segment."
   ::= { mplsOutSegmentPerfEntry 2 }

mplsOutSegmentPerfErrors OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "Number of packets that could not be sent due to
        errors on this segment."
   ::= { mplsOutSegmentPerfEntry 3 }




MPLS Working Group            Expires March 2004            [Page 32]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



mplsOutSegmentPerfDiscards OBJECT-TYPE
   SYNTAX        Counter32
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "The number of labeled packets attempted to be transmitted
        on this out-segment, which were chosen to be discarded
        even though no errors had been detected to prevent their
        being transmitted. One possible reason for
        discarding such a labeled packet could be to free up
        buffer space."
   ::= { mplsOutSegmentPerfEntry 4 }

mplsOutSegmentPerfHCOctets OBJECT-TYPE
   SYNTAX        Counter64
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "Total number of octets sent.  This is the 64 bit
        version of mplsOutSegmentPerfOctets,
        if mplsOutSegmentPerfHCOctets is supported according to
        the rules spelled out in RFC2863."
   ::= { mplsOutSegmentPerfEntry 5 }

mplsOutSegmentPerfDiscontinuityTime OBJECT-TYPE
   SYNTAX      TimeStamp
   MAX-ACCESS  read-only
   STATUS      current
   DESCRIPTION
       "The value of sysUpTime on the most recent occasion
        at which any one or more of this segment's Counter32
        or Counter64 suffered a discontinuity. If no such
        discontinuities have occurred since the last re-
        initialization of the local management subsystem,
        then this object contains a zero value."
   ::= { mplsOutSegmentPerfEntry 6 }

-- End of mplsOutSegmentPerfTable.


-- Cross-connect table.

mplsXCIndexNext OBJECT-TYPE
   SYNTAX        MplsIndexNextType
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object contains the next available value to
        be used for mplsXCIndex when creating entries in
        the mplsXCTable. A special value of the zero length



MPLS Working Group            Expires March 2004            [Page 33]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



        string indicates that no more new entries can be created
        in the relevant table.  Agents not allowing managers
        to create entries in this table MUST set this value
        to the zero length string."
   ::= { mplsLsrObjects 9 }

mplsXCTable  OBJECT-TYPE
   SYNTAX        SEQUENCE OF MplsXCEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies information for switching
        between LSP segments.  It supports point-to-point,
        point-to-multipoint and multipoint-to-point
        connections.  mplsLabelStackTable specifies the
        label stack information for a cross-connect LSR and
        is referred to from mplsXCTable."
   ::= { mplsLsrObjects 10 }

mplsXCEntry  OBJECT-TYPE
   SYNTAX        MplsXCEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "A row in this table represents one cross-connect
        entry.  It is indexed by the following objects:

        - cross-connect index mplsXCIndex that uniquely
          identifies a group of cross-connect entries

        - in-segment index, mplsXCInSegmentIndex

        - out-segment index, mplsXCOutSegmentIndex

       LSPs originating at this LSR:
        These are represented by using the special
        of value of mplsXCInSegmentIndex set to the
        string containing a single octet 0x00. In
        this case the mplsXCOutSegmentIndex
        MUST not be the string containing a single
        octet 0x00.

       LSPs terminating at this LSR:
        These are represented by using the special value
        mplsXCOutSegmentIndex set to the string containing
        a single octet 0x00.

       Special labels:
        Entries indexed by the strings containing the
        reserved MPLS label values as a single octet 0x00



MPLS Working Group            Expires March 2004            [Page 34]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



        through 0x0f (inclusive) imply LSPs terminating at
        this LSR.  Note that situations where LSPs are
        terminated with incoming label equal to the string
        containing a single octet 0x00 can be distinguished
        from LSPs originating at this LSR because the
        mplsXCOutSegmentIndex equals the string containing the
        single octet 0x00.

        An entry can be created by a network administrator
        or by an SNMP agent as instructed by an MPLS
        signaling protocol."
   INDEX { mplsXCIndex, mplsXCInSegmentIndex,
           mplsXCOutSegmentIndex }
   ::= { mplsXCTable 1 }

MplsXCEntry ::= SEQUENCE {
      mplsXCIndex                  MplsIndexType,
      mplsXCInSegmentIndex         MplsIndexType,
      mplsXCOutSegmentIndex        MplsIndexType,
      mplsXCLspId                  MplsLSPID,
      mplsXCLabelStackIndex        MplsIndexType,
      mplsXCOwner                  MplsOwner ,
      mplsXCRowStatus              RowStatus,
      mplsXCStorageType            StorageType,
      mplsXCAdminStatus            INTEGER,
      mplsXCOperStatus             INTEGER
   }

mplsXCIndex OBJECT-TYPE
   SYNTAX        MplsIndexType
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "Primary index for the conceptual row identifying a
        group of cross-connect segments. The string
        containing a single octet 0x00 is an invalid index."
   ::= { mplsXCEntry 1 }

mplsXCInSegmentIndex OBJECT-TYPE
   SYNTAX        MplsIndexType
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "Incoming label index.
        If this object is set to the string containing
        a single octet 0x00, this indicates a special
        case outlined in the table's description above.
        In this case no corresponding mplsInSegmentEntry
        shall exist."
   ::= { mplsXCEntry 2 }



MPLS Working Group            Expires March 2004            [Page 35]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003




mplsXCOutSegmentIndex OBJECT-TYPE
   SYNTAX        MplsIndexType
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "Index of out-segment for LSPs not terminating on
        this LSR if not set to the string containing the
        single octet 0x00. If the segment identified by this
        entry is terminating, then this object MUST be set to
        the string containing a single octet 0x00 to indicate
        that no corresponding mplsOutSegmentEntry shall
        exist."
   ::= { mplsXCEntry 3 }

mplsXCLspId OBJECT-TYPE
   SYNTAX        MplsLSPID
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This value identifies the label switched path that
        this cross-connect entry belongs to. This object
        cannot be modified if mplsXCRowStatus is active(1)
        except for this object."
   ::= { mplsXCEntry 4 }

mplsXCLabelStackIndex OBJECT-TYPE
   SYNTAX        MplsIndexType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "Primary index into mplsLabelStackTable identifying a
        stack of labels to be pushed beneath the top label.
        Note that the top label identified by the out-
        segment ensures that all the components of a
        multipoint-to-point connection have the same
        outgoing label. A value of the string containing the
        single octet 0x00 indicates that no labels are to
        be stacked beneath the top label.
        This object cannot be modified if mplsXCRowStatus is
        active(1)."
   ::= { mplsXCEntry 5 }

mplsXCOwner OBJECT-TYPE
   SYNTAX    MplsOwner
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "Denotes the entity that created and is responsible
        for managing this cross-connect."



MPLS Working Group            Expires March 2004            [Page 36]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   ::= { mplsXCEntry 6 }

mplsXCRowStatus OBJECT-TYPE
   SYNTAX        RowStatus
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "For creating, modifying, and deleting this row.
        When a row in this table has a row in the active(1)
        state, no objects in this row except this object
        and the mplsXCStorageType can be modified.
        Modification of mplsXCStorateType MUST be done
        as specified in the description of that object."
   ::= { mplsXCEntry 7 }

mplsXCStorageType OBJECT-TYPE
   SYNTAX        StorageType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This variable indicates the storage type for this
        object. The agent MUST ensure that the associated in
        and out segments also have the same StorageType value
        and are restored consistently upon system restart.
        This value SHOULD be set to permanent(4) if created
        as a result of a static LSP configuration.

        Conceptual rows having the value 'permanent'
        need not allow write-access to any columnar
        objects in the row."
   DEFVAL { volatile }
   ::= { mplsXCEntry 8 }

mplsXCAdminStatus OBJECT-TYPE
   SYNTAX   INTEGER {
              up(1),     -- ready to pass packets
              down(2),
              testing(3) -- in some test mode
      }
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The desired operational status of this segment."
   DEFVAL { up }
   ::= { mplsXCEntry 9 }

mplsXCOperStatus OBJECT-TYPE
   SYNTAX   INTEGER {
             up(1),            -- ready to pass packets
             down(2),



MPLS Working Group            Expires March 2004            [Page 37]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



             testing(3),       -- in some test mode
             unknown(4),       -- status cannot be determined
                               -- for some reason.
             dormant(5),
             notPresent(6),    -- some component is missing
             lowerLayerDown(7) -- down due to the state of
                               -- lower layer interfaces
      }
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "The actual operational status of this cross-
        connect."
   ::= { mplsXCEntry 10 }

-- End of mplsXCTable


-- Label stack table.

mplsMaxLabelStackDepth  OBJECT-TYPE
   SYNTAX        Unsigned32 (1..2147483647)
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "The maximum stack depth supported by this LSR."
::= { mplsLsrObjects 11 }

mplsLabelStackIndexNext  OBJECT-TYPE
   SYNTAX        MplsIndexNextType
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This object contains the next available value to
        be used for mplsLabelStackIndex when creating entries
        in the mplsLabelStackTable. The special string
        containing the single octet 0x00
        indicates that no more new entries can be created
        in the relevant table.  Agents not allowing managers
        to create entries in this table MUST set this value
        to the string containing the single octet 0x00."
::= { mplsLsrObjects 12 }

mplsLabelStackTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF MplsLabelStackEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies the label stack to be pushed
        onto a packet, beneath the top label.  Entries into



MPLS Working Group            Expires March 2004            [Page 38]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



        this table are referred to from mplsXCTable."
   ::= { mplsLsrObjects 13 }

mplsLabelStackEntry OBJECT-TYPE
   SYNTAX        MplsLabelStackEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table represents one label which is
        to be pushed onto an outgoing packet, beneath the
        top label.  An entry can be created by a network
        administrator or by an SNMP agent as instructed by
        an MPLS signaling protocol."
   INDEX { mplsLabelStackIndex, mplsLabelStackLabelIndex }
   ::= { mplsLabelStackTable 1 }

MplsLabelStackEntry ::= SEQUENCE {
      mplsLabelStackIndex             MplsIndexType,
      mplsLabelStackLabelIndex        Unsigned32,
      mplsLabelStackLabel             MplsLabel,
      mplsLabelStackLabelPtr          RowPointer,
      mplsLabelStackRowStatus         RowStatus,
      mplsLabelStackStorageType       StorageType
   }

mplsLabelStackIndex OBJECT-TYPE
   SYNTAX        MplsIndexType
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "Primary index for this row identifying a stack of
        labels to be pushed on an outgoing packet, beneath
        the top label. An index containing the string with
        a single octet 0x00 MUST not be used."
   ::= { mplsLabelStackEntry 1 }

mplsLabelStackLabelIndex OBJECT-TYPE
   SYNTAX        Unsigned32 (1..2147483647)
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "Secondary index for this row identifying one label
        of the stack.  Note that an entry with a smaller
        mplsLabelStackLabelIndex would refer to a label
        higher up the label stack and would be popped at a
        downstream LSR before a label represented by a
        higher mplsLabelStackLabelIndex at a downstream
        LSR."
   ::= { mplsLabelStackEntry 2 }




MPLS Working Group            Expires March 2004            [Page 39]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



mplsLabelStackLabel OBJECT-TYPE
   SYNTAX        MplsLabel
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The label to pushed."
   ::= { mplsLabelStackEntry 3 }

mplsLabelStackLabelPtr OBJECT-TYPE
   SYNTAX        RowPointer
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "If the label for this segment cannot be represented
        fully within the mplsLabelStackLabel object,
        this object MUST point to the first accessible
        column of a conceptual row in an external table containing
        the label.  In this case, the mplsLabelStackLabel
        object SHOULD be set to 0 and ignored. This object
        MUST be set to zeroDotZero otherwise."
   DEFVAL { zeroDotZero }
   ::= { mplsLabelStackEntry 4 }

mplsLabelStackRowStatus OBJECT-TYPE
   SYNTAX        RowStatus
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "For creating, modifying, and deleting this row.
        When a row in this table has a row in the active(1)
        state, no objects in this row except this object
        and the mplsLabelStackStorageType can be modified."
   ::= { mplsLabelStackEntry 5 }

mplsLabelStackStorageType OBJECT-TYPE
   SYNTAX        StorageType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This variable indicates the storage type for this
        object. This object cannot be modified if
        mplsLabelStackRowStatus is active(1).
        No objects are required to be writable for
        rows in this table with this object set to
        permanent(4).

        The agent MUST ensure that all related entries
        in this table retain the same value for this
        object.  Agents MUST ensure that the storage type
        for all entries related to a particular mplsXCEntry



MPLS Working Group            Expires March 2004            [Page 40]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



        retain the same value for this object as the
        mplsXCEntry's StorageType."
   DEFVAL { volatile }
   ::= { mplsLabelStackEntry 6 }

-- End of mplsLabelStackTable

-- Begin mplsInSegmentMapTable

mplsInSegmentMapTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF MplsInSegmentMapEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies the mapping from the
        mplsInSegmentIndex to the corresponding
        mplsInSegmentInterface and mplsInSegmentLabel
        objects. The purpose of this table is to
        provide the manager with an alternative
        means by which to locate in-segments."
   ::= { mplsLsrObjects 14 }

mplsInSegmentMapEntry OBJECT-TYPE
   SYNTAX        MplsInSegmentMapEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table represents one interface
        and incoming label pair.

        In cases where the label cannot fit into the
        mplsInSegmentLabel object, the mplsInSegmentLabelPtr
        will indicate this by being set to the first accessible
        colum in the appropriate extension table's row,
        and the mplsInSegmentLabel SHOULD be set to 0.
        In all other cases when the label is
        represented within the mplsInSegmentLabel object, the
        mplsInSegmentLabelPtr MUST be 0.0.

        Implementors need to be aware that if the value of
        the mplsInSegmentMapLabelPtrIndex (an OID) has more
        that 111 sub-identifiers, then OIDs of column
        instances in this table will have more than 128
        sub-identifiers and cannot be accessed using SNMPv1,
        SNMPv2c, or SNMPv3."
   INDEX { mplsInSegmentMapInterface,
           mplsInSegmentMapLabel,
           mplsInSegmentMapLabelPtrIndex }
   ::= { mplsInSegmentMapTable 1 }




MPLS Working Group            Expires March 2004            [Page 41]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



MplsInSegmentMapEntry ::= SEQUENCE {
      mplsInSegmentMapInterface      InterfaceIndexOrZero,
      mplsInSegmentMapLabel          MplsLabel,
      mplsInSegmentMapLabelPtrIndex  RowPointer,
      mplsInSegmentMapIndex          MplsIndexType
   }

mplsInSegmentMapInterface OBJECT-TYPE
   SYNTAX        InterfaceIndexOrZero
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This index contains the same value as the
        mplsInSegmentIndex in the mplsInSegmentTable."
   ::= { mplsInSegmentMapEntry 1 }

mplsInSegmentMapLabel OBJECT-TYPE
   SYNTAX        MplsLabel
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This index contains the same value as the
        mplsInSegmentLabel in the mplsInSegmentTable."
   ::= { mplsInSegmentMapEntry 2 }

mplsInSegmentMapLabelPtrIndex OBJECT-TYPE
   SYNTAX        RowPointer
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This index contains the same value as the
        mplsInSegmentLabelPtr.

        If the label for the InSegment cannot be represented
        fully within the mplsInSegmentLabel object,
        this index MUST point to the first accessible
        column of a conceptual row in an external table containing
        the label.  In this case, the mplsInSegmentTopLabel
        object SHOULD be set to 0 and ignored. This object MUST
        be set to zeroDotZero otherwise."
   ::= { mplsInSegmentMapEntry 3 }

mplsInSegmentMapIndex OBJECT-TYPE
   SYNTAX        MplsIndexType
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "The mplsInSegmentIndex that corresponds
        to the mplsInSegmentInterface and
        mplsInSegmentLabel, or the mplsInSegmentInterface



MPLS Working Group            Expires March 2004            [Page 42]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



        and mplsInSegmentLabelPtr, if applicable.
        The string containing the single octet 0x00
        MUST not be returned."
   ::= { mplsInSegmentMapEntry 4 }

-- End mplsInSegmentMapTable


-- Notification Configuration

mplsXCNotificationsEnable OBJECT-TYPE
   SYNTAX        TruthValue
   MAX-ACCESS    read-write
   STATUS        current
   DESCRIPTION
       "If this object is set to true(1), then it enables
        the emission of mplsXCUp and mplsXCDown
        notifications; otherwise these notifications are not
        emitted."
   REFERENCE
       "See also RFC3413 for explanation that
        notifications are under the ultimate control of the
        MIB modules in this document."
   DEFVAL { false }
   ::= { mplsLsrObjects 15 }

-- Cross-connect.

mplsXCUp NOTIFICATION-TYPE
   OBJECTS     { mplsXCOperStatus,  -- start of range
                 mplsXCOperStatus   -- end of range
   }
   STATUS      current
   DESCRIPTION
       "This notification is generated when the
        mplsXCOperStatus object for one or more contiguous
        entries in mplsXCTable are about to enter the up(1)
        state from some other state. The included values of
        mplsXCOperStatus MUST both be set equal to this
        new state (i.e: up(1)).  The two instances of
        mplsXCOperStatus in this notification indicate the range
        of indexes that are affected.  Note that all the indexes
        of the two ends of the range can be derived from the
        instance identifiers of these two objects.  For
        cases where a contiguous range of cross-connects
        have transitioned into the up(1) state at roughly
        the same time, the device SHOULD issue a single
        notification for each range of contiguous indexes in
        an effort to minimize the emission of a large number
        of notifications.  If a notification has to be



MPLS Working Group            Expires March 2004            [Page 43]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



        issued for just a single cross-connect entry, then
        the instance identifier (and values) of the two
        mplsXCOperStatus objects MUST be the identical."
   ::= { mplsLsrNotifications 1 }

mplsXCDown NOTIFICATION-TYPE
   OBJECTS     {
      mplsXCOperStatus,  -- start of range
      mplsXCOperStatus   -- end of range
   }
   STATUS      current
   DESCRIPTION
       "This notification is generated when the
        mplsXCOperStatus object for one or more contiguous
        entries in mplsXCTable are about to enter the
        down(2) state from some other state. The included values
        of mplsXCOperStatus MUST both be set equal to this
        down(2) state.  The two instances of mplsXCOperStatus
        in this notification indicate the range of indexes
        that are affected.  Note that all the indexes of the
        two ends of the range can be derived from the
        instance identifiers of these two objects.  For
        cases where a contiguous range of cross-connects
        have transitioned into the down(2) state at roughly
        the same time, the device SHOULD issue a single
        notification for each range of contiguous indexes in
        an effort to minimize the emission of a large number
        of notifications.  If a notification has to be
        issued for just a single cross-connect entry, then
        the instance identifier (and values) of the two
        mplsXCOperStatus objects MUST be identical."
   ::= { mplsLsrNotifications 2 }

-- End of notifications.


-- Module compliance.

mplsLsrGroups
   OBJECT IDENTIFIER ::= { mplsLsrConformance 1 }

mplsLsrCompliances
   OBJECT IDENTIFIER ::= { mplsLsrConformance 2 }

-- Compliance requirement for fully compliant implementations.

mplsLsrModuleFullCompliance MODULE-COMPLIANCE
   STATUS       current
   DESCRIPTION "Compliance statement for agents that provide full
                support for MPLS-LSR-STD-MIB. Such devices can



MPLS Working Group            Expires March 2004            [Page 44]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



                then be monitored and also be configured using
                this MIB module."

   MODULE IF-MIB -- The Interfaces Group MIB, RFC 2863.
   MANDATORY-GROUPS {
      ifGeneralInformationGroup,
      ifCounterDiscontinuityGroup
   }

   MODULE -- This module.
   MANDATORY-GROUPS {
         mplsInterfaceGroup,
         mplsInSegmentGroup,
         mplsOutSegmentGroup,
         mplsXCGroup,
         mplsPerfGroup
   }

   GROUP        mplsLabelStackGroup
   DESCRIPTION "This group is only mandatory for LSRs that wish to
                support the modification of LSP label stacks.
               "

   GROUP        mplsHCInSegmentPerfGroup
   DESCRIPTION "This group is mandatory for those in-segment entries
                for which the object mplsInSegmentOutOctets wraps
                around too quickly based on the criteria specified in
                RFC 2863 for high-capacity counters.
               "

   GROUP        mplsHCOutSegmentPerfGroup
   DESCRIPTION "This group is mandatory for those out-segment entries
                for which the object mplsOutSegmentPerfOctets wraps
                around too quickly based on the criteria specified in
                RFC 2863 for high-capacity counters.
               "

   GROUP        mplsLsrNotificationGroup
   DESCRIPTION "This group is only mandatory for those implementations
                which can efficiently implement the notifications
                contained in this group."

   OBJECT       mplsInSegmentRowStatus
   SYNTAX       RowStatus { active(1), notInService(2) }
   WRITE-SYNTAX RowStatus { active(1), notInService(2),
                            createAndGo(4), destroy(6)
                          }
   DESCRIPTION "Support for notInservice, createAndWait and notReady
                is not required.
               "



MPLS Working Group            Expires March 2004            [Page 45]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003




   OBJECT       mplsOutSegmentNextHopAddrType
   SYNTAX       InetAddressType { unknown(0), ipv4(1), ipv6(2) }
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required.  Only unknown(0),
                ipv4(1) and ipv6(2) support is required.
               "

   OBJECT       mplsOutSegmentNextHopAddr
   SYNTAX       InetAddress (SIZE(0|4|16))
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required. An implementation is
                only required to support unknown(0), ipv4(1) and
                ipv6(2) sizes."

   OBJECT       mplsOutSegmentRowStatus
   SYNTAX       RowStatus { active(1), notInService(2) }
   WRITE-SYNTAX RowStatus { active(1), notInService(2),
                            createAndGo(4), destroy(6)
                          }
   DESCRIPTION "Support for notInservice, createAndWait and notReady
                is not required.
               "

   OBJECT       mplsLabelStackRowStatus
   SYNTAX       RowStatus { active(1), notInService(2) }
   WRITE-SYNTAX RowStatus { active(1), notInService(2),
                            createAndGo(4), destroy(6)
                          }
   DESCRIPTION "Support for notInservice, createAndWait and notReady
                is not required.
               "

   OBJECT       mplsXCRowStatus
   SYNTAX       RowStatus { active(1), notInService(2) }
   WRITE-SYNTAX RowStatus { active(1), notInService(2),
                            createAndGo(4), destroy(6)
                          }
   DESCRIPTION "Support for notInservice, createAndWait and notReady
                is not required.
               "

   ::= { mplsLsrCompliances 1 }

-- Compliance requirement for read-only implementations.

mplsLsrModuleReadOnlyCompliance MODULE-COMPLIANCE
   STATUS       current
   DESCRIPTION "Compliance requirement for implementations that only
                provide read-only support for MPLS-LSR-STD-MIB. Such



MPLS Working Group            Expires March 2004            [Page 46]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



                devices can then be monitored but cannot be configured
                using this MIB modules.
               "

   MODULE IF-MIB -- The interfaces Group MIB, RFC 2863
   MANDATORY-GROUPS {
      ifGeneralInformationGroup,
      ifCounterDiscontinuityGroup
   }

   MODULE -- This module
   MANDATORY-GROUPS {
         mplsInterfaceGroup,
         mplsInSegmentGroup,
         mplsOutSegmentGroup,
         mplsXCGroup,
         mplsPerfGroup
     }

   GROUP        mplsLabelStackGroup
   DESCRIPTION "This group is only mandatory for LSRs that wish to
                support the modification of LSP label stacks.
               "

   GROUP        mplsHCInSegmentPerfGroup
   DESCRIPTION "This group is mandatory for those in-segment entries
                for which the object mplsInSegmentOutOctets wraps
                around too quickly based on the criteria specified in
                RFC 2863 for high-capacity counters.
               "

   GROUP        mplsHCOutSegmentPerfGroup
   DESCRIPTION "This group is mandatory for those out-segment entries
                for which the object mplsOutSegmentPerfOctets wraps
                around too quickly based on the criteria specified in
                RFC 2863 for high-capacity counters.
               "

   GROUP        mplsLsrNotificationGroup
   DESCRIPTION "This group is only mandatory for those implementations
                which can efficiently implement the notifications
                contained in this group.
               "

   -- mplsInSegmentTable
   OBJECT       mplsInSegmentLabel
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   OBJECT       mplsInSegmentLabelPtr



MPLS Working Group            Expires March 2004            [Page 47]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   OBJECT       mplsInSegmentNPop
   SYNTAX       Integer32 (1..1)
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required.  This object
                SHOULD be set to 1 if it is read-only.
               "

   OBJECT       mplsInSegmentAddrFamily
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required.  A value of other(0)
                should be supported because there may be cases where
                the agent may not know about or support any address
                types.
               "

   OBJECT       mplsInSegmentRowStatus
   SYNTAX       RowStatus { active(1) }
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   OBJECT       mplsInSegmentStorageType
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   -- mplsOutSegmentTable
   OBJECT       mplsOutSegmentInterface
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   OBJECT       mplsOutSegmentPushTopLabel
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   OBJECT       mplsOutSegmentTopLabel
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   OBJECT       mplsOutSegmentTopLabelPtr
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   OBJECT       mplsOutSegmentNextHopAddrType
   SYNTAX       InetAddressType { unknown(0), ipv4(1), ipv6(2) }
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required.  Only unknown(0),
                ipv4(1) and ipv6(2) support is required.
               "



MPLS Working Group            Expires March 2004            [Page 48]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003




   OBJECT       mplsOutSegmentNextHopAddr
   SYNTAX       InetAddress (SIZE(0|4|16))
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required. An implementation is
                only required to support unknown(0), ipv4(1) and
                ipv6(2) sizes."

   OBJECT       mplsOutSegmentRowStatus
   SYNTAX       RowStatus { active(1) }
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   OBJECT       mplsOutSegmentStorageType
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   -- mplsXCTable
   OBJECT       mplsXCLabelStackIndex
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   OBJECT       mplsXCAdminStatus
   MIN-ACCESS   read-only
   DESCRIPTION "Read only support is required."

   OBJECT       mplsXCRowStatus
   SYNTAX       RowStatus { active(1) }
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   OBJECT       mplsXCStorageType
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   OBJECT       mplsLabelStackLabel
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   OBJECT       mplsLabelStackLabelPtr
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   OBJECT       mplsLabelStackRowStatus
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."

   OBJECT       mplsLabelStackStorageType
   MIN-ACCESS   read-only
   DESCRIPTION "Write access is not required."



MPLS Working Group            Expires March 2004            [Page 49]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003




   ::= { mplsLsrCompliances 2 }

-- Units of conformance.

mplsInterfaceGroup OBJECT-GROUP
   OBJECTS {
      mplsInterfaceLabelMinIn,
      mplsInterfaceLabelMaxIn,
      mplsInterfaceLabelMinOut,
      mplsInterfaceLabelMaxOut,
      mplsInterfaceTotalBandwidth,
      mplsInterfaceAvailableBandwidth,
      mplsInterfaceLabelParticipationType
   }
   STATUS  current
   DESCRIPTION
          "Collection of objects needed for MPLS interface
           and interface performance information."
   ::= { mplsLsrGroups 1 }

mplsInSegmentGroup  OBJECT-GROUP
   OBJECTS {
      mplsInSegmentIndexNext,
      mplsInSegmentInterface,
      mplsInSegmentLabel,
      mplsInSegmentLabelPtr,
      mplsInSegmentNPop,
      mplsInSegmentAddrFamily,
      mplsInSegmentXCIndex,
      mplsInSegmentOwner,
      mplsInSegmentRowStatus,
      mplsInSegmentStorageType,
      mplsInSegmentTrafficParamPtr,
      mplsInSegmentMapIndex
   }
   STATUS  current
   DESCRIPTION
          "Collection of objects needed to implement an in-
           segment."
   ::= { mplsLsrGroups 2 }

mplsOutSegmentGroup  OBJECT-GROUP
   OBJECTS {
      mplsOutSegmentIndexNext,
      mplsOutSegmentInterface,
      mplsOutSegmentPushTopLabel,
      mplsOutSegmentTopLabel,
      mplsOutSegmentTopLabelPtr,
      mplsOutSegmentNextHopAddrType,



MPLS Working Group            Expires March 2004            [Page 50]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



      mplsOutSegmentNextHopAddr,
      mplsOutSegmentXCIndex,
      mplsOutSegmentOwner,
      mplsOutSegmentPerfOctets,
      mplsOutSegmentPerfDiscards,
      mplsOutSegmentPerfErrors,
      mplsOutSegmentRowStatus,
      mplsOutSegmentStorageType,
      mplsOutSegmentTrafficParamPtr
   }
   STATUS  current
   DESCRIPTION
          "Collection of objects needed to implement an out-
           segment."
   ::= { mplsLsrGroups 3 }

mplsXCGroup  OBJECT-GROUP
   OBJECTS {
      mplsXCIndexNext,
      mplsXCLspId,
      mplsXCLabelStackIndex,
      mplsXCOwner,
      mplsXCStorageType,
      mplsXCAdminStatus,
      mplsXCOperStatus,
      mplsXCRowStatus,
      mplsXCNotificationsEnable
   }
   STATUS  current
   DESCRIPTION
          "Collection of objects needed to implement a
           cross-connect entry."
   ::= { mplsLsrGroups 4 }

mplsPerfGroup OBJECT-GROUP
   OBJECTS {
      mplsInSegmentPerfOctets,
      mplsInSegmentPerfPackets,
      mplsInSegmentPerfErrors,
      mplsInSegmentPerfDiscards,
      mplsInSegmentPerfDiscontinuityTime,
      mplsOutSegmentPerfOctets,
      mplsOutSegmentPerfPackets,
      mplsOutSegmentPerfDiscards,
      mplsOutSegmentPerfDiscontinuityTime,
      mplsInterfacePerfInLabelsInUse,
      mplsInterfacePerfInLabelLookupFailures,
      mplsInterfacePerfOutFragmentedPkts,
      mplsInterfacePerfOutLabelsInUse
   }



MPLS Working Group            Expires March 2004            [Page 51]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003




   STATUS  current
   DESCRIPTION
          "Collection of objects providing performance
           information
        about an LSR."
   ::= { mplsLsrGroups 5 }

mplsHCInSegmentPerfGroup OBJECT-GROUP
   OBJECTS { mplsInSegmentPerfHCOctets }
   STATUS  current
   DESCRIPTION
          "Object(s) providing performance information
           specific to out-segments for which the object
           mplsInterfaceInOctets wraps around too quickly."
   ::= { mplsLsrGroups 6 }

mplsHCOutSegmentPerfGroup OBJECT-GROUP
   OBJECTS { mplsOutSegmentPerfHCOctets }
   STATUS  current
   DESCRIPTION
          "Object(s) providing performance information
           specific to out-segments for which the object
           mplsInterfaceOutOctets wraps around too
           quickly."
   ::= { mplsLsrGroups 7 }

mplsLabelStackGroup OBJECT-GROUP
   OBJECTS {
      mplsLabelStackLabel,
      mplsLabelStackLabelPtr,
      mplsLabelStackRowStatus,
      mplsLabelStackStorageType,
      mplsMaxLabelStackDepth,
      mplsLabelStackIndexNext
   }
   STATUS current
   DESCRIPTION
          "Objects needed to support label stacking."
      ::= { mplsLsrGroups 8 }

mplsLsrNotificationGroup NOTIFICATION-GROUP
   NOTIFICATIONS {
      mplsXCUp,
      mplsXCDown
   }
   STATUS  current
   DESCRIPTION
          "Set of notifications implemented in this
           module."



MPLS Working Group            Expires March 2004            [Page 52]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   ::= { mplsLsrGroups 9 }
END


11.   Security Considerations

   It is clear that this MIB module is potentially useful for
   monitoring of MPLS LSRs.  This MIB can also be used for
   configuration of certain objects, and anything that can be
   configured can be incorrectly configured, with potentially
   disastrous results.

   There are a number of management objects defined in this MIB module
   with a MAX-ACCESS clause of read-write and/or read-create.  Such
   objects may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.  These are the tables and objects and their
   sensitivity/vulnerability:

   o    the mplsLsrInSegmentTable, mplsLsrOutSegmentTable,
        mplsXCTable, mplsOutSegmentPerfTable, mplsInterfacePerfTable,
        and mplsInSegmentPerfTable collectively contain objects to
        provision MPLS interfaces, LSPs and their associated parameters
        on an Label Switching Router (LSR).  Unauthorized access to
        objects in these tables, could result in disruption of traffic
        on the network.  This is especially true if an LSP has been
        established.  The use of stronger mechanisms such as SNMPv3
        security should be considered where possible.  Specifically,
        SNMPv3 VACM and USM MUST be used with any v3 agent which
        implements this MIB module.  Administrators should consider
        whether read access to these objects should be allowed,
        since read access may be undesirable under certain
        circumstances.

   Some of the readable objects in this MIB module "i.e., objects with a
   MAX-ACCESS other than not-accessible" may be considered sensitive or
   vulnerable in some network environments.  It is thus important to
   control even GET and/or NOTIFY access to these objects and possibly
   to even encrypt the values of these objects when sending them over
   the network via SNMP.  These are the tables and objects and their
   sensitivity/vulnerability:

   o    the mplsLsrInSegmentTable, mplsLsrOutSegmentTable,
        mplsXCTable, mplsOutSegmentPerfTable, mplsInterfacePerfTable,
        and mplsInSegmentPerfTable collectively show the LSP network
        topology and its performance characteristics.
        If an Administrator does not want to reveal this
        information, then these tables should be
        considered sensitive/vulnerable.



MPLS Working Group            Expires March 2004            [Page 53]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003




   SNMP versions prior to SNMPv3 did not include adequate security.
   Even if the network itself is secure "for example by using IPSec",
   even then, there is no control as to who on the secure network is
   allowed to access and GET/SET "read/change/create/delete" the objects
   in this MIB module.

   It is RECOMMENDED that implementers consider the security features as
   provided by the SNMPv3 framework "see [RFC3410], section 8",
   including full support for the SNMPv3 cryptographic mechanisms "for
   authentication and privacy".

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module, is properly configured to give access
   to the objects only to those principals "users" that have legitimate
   rights to indeed GET or SET "change/create/delete" them.

12.   Acknowledgments

   We wish to thank Ron Bonica, Adrian Farrel, Eric Gray, Tim
   Mancour, Keith McCloghrie, Bala Rajagopalan, Dan Tappan, Vasanthi
   Thirumalai, Joseph Benoit, Mike Piecuch, Joan Cucchiara.
   A special thanks to Bert Wijnen and Mike MacFaden for really
   getting the MIB module into shape.


13.  IANA Considerations
   As described in [MPLSMGMT] and as requested in the MPLS-TC-STD-MIB
   [MPLSTCMIB], MPLS related standards track MIB modules should be
   rooted under the mplsStdMIB subtree.  There are 4 MPLS MIB Modules
   contained in this document, each of the following "IANA
   Considerations" subsections requests IANA for a new assignment under
   the mplsStdMIB subtree.  New assignments can only be made via a
   Standards Action as specified in [RFC2434].

13.1.  IANA Considerations for MPLS-LSR-STD-MIB
   The IANA is requested to assign { mplsStdMIB 2 } to the
   MPLS-LSR-STD-MIB module specified in this document.

14.   References

14.1. Normative References

   [RFC2119]     S. Bradner, "Key Words for use in RFCs to Indicate
                 Requirement Levels", RFC 2119, BCP 14, March 1997.

   [RFC2515]     Tesink, K., et al., "Definitions of Managed Objects



MPLS Working Group            Expires March 2004            [Page 54]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



                 for ATM Management", RFC 2515, February 1999.

   [RFC2578]     McCloghrie, K., Perkins, D., Schoenwaelder, J., Case,
                 J., Rose, M., and S. Waldbusser, "Structure of
                 Management Information Version 2 (SMIv2)", STD 58, RFC
                 2578, April 1999.

   [RFC2579]     McCloghrie, K., Perkins, D., Schoenwaelder, J., Case,
                 J., Rose, M., and S. Waldbusser, "Textual Conventions
                 for SMIv2", STD 58, RFC 2579, April 1999.

   [RFC2580]     McCloghrie, K., Perkins, D., Schoenwaelder, J., Case,
                 J., Rose, M., and S. Waldbusser, "Conformance
                 Statements for SMIv2", STD 58, RFC 2580, April 1999.

   [RFC2863]     McCloghrie, K. and F. Kastenholz, "The Interfaces
                 Group MIB", RFC 2863, June 2000.

   [RFC3031]     Rosen, E., Viswanathan, A., and R. Callon,
                 "Multiprotocol Label Switching Architecture", RFC
                 3031, January 2001.

   [RFC3291]     Daniele, M., Haberman, B., Routhier., S.,
                 Schoenwaelder., J., "Textual Conventions
                 for Internet Network Addresses", RFC3291,
                 May 2002.

   [RFC3411]     Harrington, D., Presuhn, R., and B. Wijnen, "An
                 Architecture for Describing Simple Network Management
                 Protocol (SNMP) Management Frameworks", RFC 3411,
                 December 2002.

   [TEMIB]       Srinivasan, C., Viswanathan, A. and Nadeau, T., "MPLS
                 Traffic Engineering Management Information Base ",
                 Internet Draft <draft-ietf-mpls-te-mib-09.txt>,
                 November 2002.

   [TCMIB]       Nadeau, T., Cucchiara, J., Srinivasan, C.,
                 Viswanathan, A., Sjostrand, H. and K. Kompella,
                 "Definition of Textual Conventions and OBJECT-
                 IDENTITIES for Multi-Protocol Label Switching (MPLS)
                 Management", Internet Draft <draft-ietf-mpls-tc-mib-
                 06.txt>, April 2003.

   [IANAFamily]  Internet Assigned Numbers Authority (IANA), ADDRESS
                 FAMILY NUMBERS, (http://www.isi.edu/in-
                 notes/iana/assignements/address-family-numbers),
                 for MIB see:
                 ftp://ftp.isi.edu/mib/iana.mib/ianaaddressfamilynum
                 bers.mib



MPLS Working Group            Expires March 2004            [Page 55]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003





14.2. Informative References


   [RFC2026]     S. Bradner, "The Internet Standards Process --
                 Revision 3", RFC 2026, October 1996.


   [RFC3413]     Levi, D., Meyer, P., Stewart, B.,
                 "SNMP Applications", RFC 3413, December 2002.

   [RFC3410]     Case, J., Mundy, R., Partain, D. and B. Stewart,
                 "Introduction and Applicability Statements for
                 Internet-Standard Management Framework", RFC 3410,
                 December 2002.



15.   Authors' Addresses

  Cheenu Srinivasan
  Bloomberg L.P.
  499 Park Ave., New York, NY 10022
  Phone: +1-212-893-3682
  Email: cheenu@bloomberg.net

  Arun Viswanathan
  Force10 Networks, Inc.
  1440 McCarthy Blvd
  Milpitas, CA 95035
  Phone: +1-408-571-3516
  Email: arunv@force10networks.com

  Thomas D. Nadeau
  Cisco Systems, Inc.
  300 Beaver Brook Road
  Boxboro, MA 01719
  Phone: +1-978-936-1470
  Email: tnadeau@cisco.com


16.   Full Copyright Statement

   Copyright (C) The Internet Society (2003).  All Rights Reserved.

   This document and translations of it may be copied and furnished
   to others, and derivative works that comment on or otherwise
   explain it or assist in its implementation may be prepared,
   copied, published and distributed, in whole or in part, without



MPLS Working Group            Expires March 2004            [Page 56]

Internet Draft            MPLS-LSR-STD-MIB            August 06, 2003



   restriction of any kind, provided that the above copyright notice
   and this paragraph are included on all such copies and derivative
   works.  However, this document itself may not be modified in any
   way, such as by removing the copyright notice or references to the
   Internet Society or other Internet organizations, except as needed
   for the  purpose of developing Internet standards in which case
   the procedures for copyrights defined in the Internet Standards
   process must be followed, or as required to translate it into
   languages other than English.

   The limited permissions granted above are perpetual and will not
   be revoked by the Internet Society or its successors or assigns.
   This document and the information contained herein is provided on
   an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET
   ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR
   IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

17.  Intellectual Property Notice

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; neither does it represent that it
   has made any effort to identify any such rights.  Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11 [RFC2028].
   Copies of claims of rights made available for publication and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementors or users of this
   specification can be obtained from the IETF Secretariat.
   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to practice
   this standard.  Please address the information to the IETF Executive
   Director.






MPLS Working Group            Expires March 2004            [Page 57]


Html markup produced by rfcmarkup 1.107, available from http://tools.ietf.org/tools/rfcmarkup/