[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits] [IPR]

Versions: (draft-vasseur-mpls-nodeid-subobject) 00 01 02 03 04 05 06 07 RFC 4561

Network Working Group                             J.-P Vasseur (Editor)
IETF Internet Draft                                           Zafar Ali
                                                         Siva Sivabalan
                                                    Cisco Systems, Inc.

Proposed Status: Standard
Expires: May 2006
                                                          November 2005



                draft-ietf-mpls-nodeid-subobject-07.txt


                 Definition of an RRO node-id subobject



Status of this Memo

By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.

Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that other
groups may also distribute working documents as Internet-Drafts.

Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time.  It is inappropriate to use Internet-Drafts as reference material
or to cite them other than as "work in progress."

The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.

The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.














Vasseur et al.                                                       1



draft-ietf-mpls-nodeid-subobject-07.txt                   November 2005


Abstract

In the context of MPLS TE Fast Reroute, the Merge Point (MP) address is
required at the Point of Local Repair (PLR) in order to select a backup
tunnel intersecting a fast reroutable Traffic Engineering Label
Switched Path (TE LSP) on a downstream Label Switching Router (LSR).
However, existing protocol mechanisms are not sufficient to find an MP
address in multi-domain routing networks where a domain is defined as
an IGP area or an Autonomous System. Hence, the current MPLS Fast
Reroute mechanism cannot be used in order to protect inter-domain TE
LSPs from a failure of an ABR (Area Border Router) or ASBR (Autonomous
System Border Router) respectively. This document specifies the use of
existing Route Record Object (RRO) IPv4 and IPv6 sub-objects (with a
new flag defined) thus defining the node-id subobject in order to solve
this issue. The MPLS Fast reroute mechanism mentioned in this document
refers to the "Facility backup" MPLS TE Fast Reroute method.

Table of content

1. Terminology...............................2
2. Introduction..............................3
3. Signaling node-ids in RROs................5
4. Finding Merge Points......................6
5. Security Considerations...................6
6. IANA Considerations.......................6
7. Intellectual Property Considerations......6
8. Acknowlegments............................7
9. References................................7
9.1 Normative References.....................7
9.2 Informative References...................7
10. Authors' addresses.......................8

Conventions used in this document

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED",  "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC-2119 [i].


1.      Terminology

ABR Routers: border routers used to connect two IGP areas (areas in
OSPF or levels in IS-IS)

ASBR Routers: border routers used to connect to another AS of a
different or the same Service Provider via one or more links inter-
connecting between ASs.

Backup Tunnel: the LSP that is used to backup up one of the many LSPs
in many-to-one backup.

Inter-AS TE LSP: A TE LSP that crosses an AS boundary.

Inter-area TE LSP: A TE LSP that crosses an IGP area.

LSR: Label Switching Router

LSP: Label Switched Path

Local Repair: techniques used to repair LSP tunnels quickly when a node
or link along the LSPs path fails.

PCE: Path Computation Element: an entity (component, application or

Vasseur, Ali and Sivabalan                                           2



draft-ietf-mpls-nodeid-subobject-07.txt                   November 2005


network node) that is capable of computing a network path or route
based on a network graph and applying computational constraints.

MP: Merge Point. The LSR where one or more backup tunnels rejoin the
path of the protected LSP downstream of the potential failure.

Protected LSP: an LSP is said to be protected at a given hop if it has
one or multiple associated backup tunnels originating at that hop.

PLR: Point of Local Repair. The head-end of a backup tunnel.

Reroutable LSP: Any LSP for with the "Local protection desired" bit is
set in the Flag field of the SESSION_ATTRIBUTE object of its Path
messages.

TE LSP: Traffic Engineering Label Switched Path

2.      Introduction

MPLS Fast Reroute (FRR) ([FAST-REROUTE]) is a fast recovery local
protection technique used to protect Traffic Engineering LSPs from
link/SRLG/node failure.  One or more backup tunnels are pre-established
to protect against the failure of a link/node/SRLG. In case of failure,
every protected TE LSP traversing the failed resource is rerouted onto
the appropriate backup tunnels.

There are several requirements on the backup tunnel path that must be
satisfied. First, the backup tunnel must not traverse the element that
it protects. Additionally, a primary tunnel and its associated backup
tunnel should intersect at least at two points (nodes): Point of Local
Repair (PLR) and Merge Point (MP). The former is the Head-end LSR of
the backup tunnel and the latter is the Tail-end LSR of the backup
tunnel. The PLR is where FRR is triggered when link/node/SRLG failure
happens.

There are different methods for computing paths for backup tunnels at a
given PLR. Specifically, a user can statically configure one or more
backup tunnels at the PLR with an explicitly configured path or the PLR
can be configured to automatically compute a backup path or to send a
path computation request to a PCE (see [PCE-ARCH]).

Consider the following scenario (figure 1)

Assumptions:
- A multi-area network made of three areas: 0, 1 and 2,
- A fast reroutable TE LSP T1 (TE LSP signaled with the "local
Protection desired" bit set in the SESSION-ATTRIBUTE object or the
FAST-REROUTE object) from R0 to R3,
- A backup tunnel B1 from R1 to R2, not traversing ABR1, and following
the R1-ABR3-R2 path.


Vasseur, Ali and Sivabalan                                           3



draft-ietf-mpls-nodeid-subobject-07.txt                   November 2005


- The PLR R1 reroutes any protected TE LSP traversing ABR1 onto the
backup tunnel B1 in case of ABR1's failure.

           <--- area 1 --><---area 0---><---area 2--->
              R0-----R1-ABR1--R2------ABR2--------R3
                     \        /
                      \      /
                        ABR3

Figure 1: Use of Fast Reroute to protect a TE LSP against an ABR
failure with MPLS Traffic Engineering Fast Reroute

When T1 is first signaled, the PLR R1 needs to dynamically select an
appropriate backup tunnel intersecting T1 on a downstream LSR. However,
existing protocol mechanisms are not sufficient to unambiguously find
the MP address in a network with inter-domain TE LSP. This document
addresses these limitations.

R1 needs to select an existing backup tunnel with the following
properties:

   1. The backup tunnel intersects with the primary tunnel at the MP.
      For the sake of illustration, in Figure 1, R1 needs to determine
      that T1 and B1 intersect at the node R2.

   2. The backup tunnel satisfies the primary LSP's request with
      respect to the bandwidth protection request (i.e., bandwidth
      guaranteed for the primary tunnel during failure), and the type
      of protection (link or node failure), as specified in [FAST-
      REROUTE].

One technique for the PLR to ensure that condition (1) is met consists
of examining the Record Route Object (RRO) of the primary tunnel to see
if any of the addresses specified in the RRO corresponds to the MP.
That said, as per [RSVP-TE], the addresses specified in the RRO IPv4 or
IPv6 sub-objects sent in Resv messages can be node-ids and/or interface
addresses. Hence, in Figure 1, router R2 may specify interface
addresses in the RROs for T1 and B1. Note that these interface
addresses are different in this example.

The problem of finding the MP using the interface addresses or node-ids
can be easily solved in the case of a single IGP area. Specifically, in
the case of a single IGP area, the PLR has the knowledge of all the
interfaces attached to the tail-end of the backup tunnel. This
information is available in PLR's IGP topology database. Thus, the PLR
can unambiguously determine whether a backup tunnel intersecting a
protected TE LSP on a downstream node exists and can also find the MP
address regardless of how the addresses carried in the RRO IPv4 or IPv6
sub-objects are specified (i.e., whether using the interface addresses
or the node-ids). However, such routing information is not available in
the case of inter-domain environments. Hence, unambiguously making sure

Vasseur, Ali and Sivabalan                                           4



draft-ietf-mpls-nodeid-subobject-07.txt                   November 2005


that condition (1) above is met in the case of inter-domain TE LSPs is
not possible with existing mechanisms.

In this document, we define extensions to and describe the use of RSVP
[RSVP, RSVP-TE] to solve the above-mentioned problem. Note that the
requirement for the support of the fast recovery technique specified in
[FAST-REROUTE] to inter-domain TE LSPs has been specified in [INTER-
AREA-TE-REQS] and [INTER-AREA-TE-REQS].

3.      Signaling node-ids in RROs

As mentioned above, the limitation that we need to address is the
generality of the contents of the RRO IPv4 and IPv6 sub-objects, as
defined in [RSVP-TE]. [RSVP-TE] defines the IPv4 and IPv6 RRO sub-
objects. Moreover, two additional flags are defined in [FAST-REROUTE]:
the "Local Protection Available" and "Local protection in use" bits.

In this document, we define the following new flag:

Node-id: 0x20

        When set, this indicates that the address specified in the
        RRO's IPv4 or IPv6 subobject is a node-id address, which refers
        to the "Router Address" as defined in [OSPF-TE], or "Traffic
        Engineering Router ID" as defined in [ISIS-TE]. A node MUST use
        the same address consistently. Once an address is used in RRO's
        IPv4 or IPv6 subobject, it SHOULD always be used for the
        lifetime of the LSP.

An IPv4 or IPv6 RRO subobject with the node-id flag set is also called
a node-id subobject. The problem of finding a MP address in a network
with inter-domain TE LSP is solved by inserting a node-id subobject (an
RRO "IPv4" and "IPv6" sub-object with the 0x20 flag set) in the RRO
object carried in the RSVP Resv message.

An implementation may either decide to:

1) Add the node-id subobject in the RRO carried in an RSVP Resv message
and, when required, also add another IPv4/IPv6 subobject to record
interface address.

Example: an inter-domain fast reroutable TE LSP would have in the RRO
carried in Resv message two sub-objects: a node-id subobject and a
label sub-object. If recording the interface address is required, then
an additional IPv4/IPv6 subobject is added.

2) Add an IPv4/IPv6 sub-object recording the interface address and,
when required, add a node-id subobject in the RRO.

Example: an inter-domain fast reroutable TE LSP would have in the RRO
carried in Resv message three sub-objects: an IPv4/IPv6 sub-object

Vasseur, Ali and Sivabalan                                           5



draft-ietf-mpls-nodeid-subobject-07.txt                   November 2005


recording interface address, a label sub-object and a node-id sub-
object.

Note also that the node-id sub-object may have other application than
Fast Reroute backup tunnel selection. Moreover, it is RECOMMENDED that
an LSR recording a node-id address in an IPv4/IPv6 RRO sub-object also
set the Node-id flag.

4.      Finding Merge Point

Two cases should be considered:

- Case 1: the backup tunnel destination is the MP's node-id. Then a PLR
can find the MP and suitable backup tunnel by simply comparing the
backup tunnel's destination address with the node-id included in the
RRO of the primary tunnel.
- Case 2: the backup tunnel terminates at an address different than the
MP's node-id. Then a node-id subobject MUST also be included in the RRO
object of the backup tunnel. A PLR can find the MP and suitable backup
tunnel by simply comparing the node-ids present in the RRO objects of
both the primary and backup tunnels.

It must be noted that although the technique described in this document
for selecting an appropriate backup tunnel using the node-id sub-object
applies to the case of Inter-area and Inter-AS, in the case of Inter-
AS, the assumption is made that the MP's node-id (of the downstream
domain) does not overlap with any LSR's node-id present in the PLR's
AS.

When both IPv4 node-id and IPv6 node-id sub-objects are present, a PLR
may use any or both of them in finding the MP address.

5.      Security Considerations

This document does not introduce new security issues. The security
considerations pertaining to [RSVP] and [RSVP-TE] remain relevant.

6.      IANA considerations

This document does not make any request for IANA action.

7.      Intellectual Property Considerations

The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has made
any independent effort to identify any such rights. Information on the
procedures with respect to rights in RFC documents can be found in BCP
78 and BCP 79.

Vasseur, Ali and Sivabalan                                           6



draft-ietf-mpls-nodeid-subobject-07.txt                   November 2005



Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this specification
can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.

The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary rights
that may cover technology that may be required to implement this
standard. Please address the information to the IETF at ietf-
ipr@ietf.org.

8.      Acknowledgments

We would like to acknowledge input and helpful comments from Carol
Iturralde, Anca Zamfir, Reshad Rahman, Rob Goguen, Philip Matthews. A
special thank to Adrian Farrel for his thorough review of this
document.

9.      References

9.1 Normative References

[RFC2119]Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.

[RSVP] Braden, et al, "Resource ReSerVation Protocol (RSVP) - Version
1, Functional Specification", RFC 2205, September 1997.

[RSVP-TE] Awduche, et al, "Extensions to RSVP for LSP Tunnels", RFC
3209, December 2001.

[FAST-REROUTE] Ping Pan, et al, "Fast Reroute Extensions to RSVP-TE for
LSP Tunnels", draft-ietf-mpls-rsvp-lsp-fastreroute-07.txt. RFC 4090,
May 2005.

[OSPF-TE] Katz et al., "Traffic Engineering (TE) Extensions to OSPF
Version 2", RFC3630.

[ISIS-TE] Smit et al., "Intermediate System to Intermediate System (IS-
IS) - Extensions for Traffic Engineering (TE)IS-IS extensions for
Traffic Engineering", RFC3784.

9.2 Informative references

[INTER-AREA-TE-REQS] Le Roux, Vasseur, Boyle et al., "Requirements for
Inter-Area MPLS Traffic Engineering", RFC 4105, June 2005.



Vasseur, Ali and Sivabalan                                           7



draft-ietf-mpls-nodeid-subobject-07.txt                   November 2005


[INTER-AS-TE-REQS] Zhang, Vasseur et al, "MPLS Inter-AS Traffic
Engineering requirements", RFC 4216, November 2005.

[PCE-ARCH] Farrel, A., Vasseur JP., Ash J., "Path Computation Element
(PCE) Architecture", draft-ietf-pce-architecture, work in progress.


10.     Authors' Addresses

J.-P Vasseur (Editor)
Cisco Systems, Inc.
1414 Massachusetts Avenue
Boxborough , MA - 01719
USA
Email: jpv@cisco.com

Zafar Ali
Cisco Systems, Inc.
100 South Main St. #200
Ann Arbor, MI 48104
USA
zali@cisco.com

Siva Sivabalan
Cisco Systems, Inc.
2000 Innovation Drive
Kanata, Ontario, K2K 3E8
Canada
msiva@cisco.com

Full Copyright Statement

Full Copyright Statement

Copyright (C) The Internet Society (2005).  This document is subject to
the rights, licenses and restrictions contained in BCP 78, and except
as set forth therein, the authors retain all their rights.

This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.







Vasseur, Ali and Sivabalan                                           8


Html markup produced by rfcmarkup 1.107, available from http://tools.ietf.org/tools/rfcmarkup/