[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: (draft-ietf-multimob-fast-handover) 00 01 02 03 04 05 06 07 RFC 7161

MULTIMOB Working Group                                     LM. Contreras
Internet-Draft                                            Telefonica I+D
Intended status: Experimental                              CJ. Bernardos
Expires: January 9, 2014                                         I. Soto
                                                                    UC3M
                                                            July 8, 2013


 PMIPv6 multicast handover optimization by the Subscription Information
                   Acquisition through the LMA (SIAL)
              draft-ietf-multimob-handover-optimization-03

Abstract

   This document specifies a multicast handover optimization mechanism
   for Proxy Mobile IPv6 to accelerate the delivery of multicast traffic
   to mobile nodes after handovers.  The mechanism is based on speeding
   up the acquisition of mobile nodes' multicast context by the mobile
   access gateways.  To do that, extensions to the current Proxy Mobile
   IPv6 protocol are proposed.  These extensions are not only applicable
   to the base solution for multicast support in Proxy Mobile IPv6, but
   they can also be applied to other solutions developed to avoid the
   tunnel convergence problem.  Furthermore, the extensions are also
   independent of the role played by the mobile access gateway within
   the multicast network (either acting as multicast listener discovery
   proxy or multicast router).

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on January 9, 2014.

Copyright Notice

   Copyright (c) 2013 IETF Trust and the persons identified as the
   document authors.  All rights reserved.



Contreras, et al.        Expires January 9, 2014                [Page 1]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  4
     1.1.  Handover optimization requirements . . . . . . . . . . . .  6
   2.  Terminology  . . . . . . . . . . . . . . . . . . . . . . . . .  6
   3.  Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .  7
   4.  Proxy Mobile IPv6 extensions . . . . . . . . . . . . . . . . .  8
     4.1.  Active Multicast Subscription mobility option  . . . . . .  9
       4.1.1.  Option application rules . . . . . . . . . . . . . . .  9
       4.1.2.  Option format  . . . . . . . . . . . . . . . . . . . .  9
       4.1.3.  Backward compatibility with MLDv1  . . . . . . . . . . 10
     4.2.  Multicast Signaling flag on PBU/PBA message headers  . . . 11
       4.2.1.  Flag application rules . . . . . . . . . . . . . . . . 11
         4.2.1.1.  Registration process . . . . . . . . . . . . . . . 11
         4.2.1.2.  De-registration process  . . . . . . . . . . . . . 12
       4.2.2.  New format of conventional PBU/PBA messages  . . . . . 12
         4.2.2.1.  Proxy Binding Update message . . . . . . . . . . . 12
         4.2.2.2.  Proxy Binding Acknowledgement Message  . . . . . . 13
     4.3.  Messages for active multicast subscription query . . . . . 13
       4.3.1.  Subscription Query message . . . . . . . . . . . . . . 13
         4.3.1.1.  Message application rules  . . . . . . . . . . . . 13
         4.3.1.2.  Message format . . . . . . . . . . . . . . . . . . 14
       4.3.2.  Subscription Response message  . . . . . . . . . . . . 15
         4.3.2.1.  Message application rules  . . . . . . . . . . . . 15
         4.3.2.2.  Message format . . . . . . . . . . . . . . . . . . 15
     4.4.  New PBA timer in the LMA . . . . . . . . . . . . . . . . . 16
   5.  Handover signaling procedures  . . . . . . . . . . . . . . . . 16
     5.1.  Handover of proactive type . . . . . . . . . . . . . . . . 17
       5.1.1.  Rationale  . . . . . . . . . . . . . . . . . . . . . . 17
       5.1.2.  Message flow description . . . . . . . . . . . . . . . 17
     5.2.  Handover of reactive type  . . . . . . . . . . . . . . . . 19
       5.2.1.  Rationale  . . . . . . . . . . . . . . . . . . . . . . 19
       5.2.2.  Message flow description . . . . . . . . . . . . . . . 20
       5.2.3.  Further considerations for the reactive handover
               signaling  . . . . . . . . . . . . . . . . . . . . . . 22
     5.3.  Prevention of large delays of the binding
           acknowledgement for unicast traffic  . . . . . . . . . . . 23



Contreras, et al.        Expires January 9, 2014                [Page 2]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   6.  IPv4 support . . . . . . . . . . . . . . . . . . . . . . . . . 26
     6.1.  Active Multicast Subscription for IPv4 . . . . . . . . . . 26
     6.2.  Signaling procedures for IPv4 support  . . . . . . . . . . 27
     6.3.  Binding Cache extensions for IPv4 support  . . . . . . . . 28
   7.  Co-existence with PMIPv6 multicast architectural evolutions  . 28
   8.  Security Considerations  . . . . . . . . . . . . . . . . . . . 28
   9.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 30
   10. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 30
   11. Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . . 30
   12. References . . . . . . . . . . . . . . . . . . . . . . . . . . 30
     12.1. Normative References . . . . . . . . . . . . . . . . . . . 30
     12.2. Informative References . . . . . . . . . . . . . . . . . . 31
   Appendix A.  Performance comparison with base solution . . . . . . 32
     A.1.  Delay characterization of the base solution  . . . . . . . 32
     A.2.  Delay characterization of the extensions defined in
           this document  . . . . . . . . . . . . . . . . . . . . . . 33
     A.3.  Performance comparison . . . . . . . . . . . . . . . . . . 34
   Appendix B.  Change Log  . . . . . . . . . . . . . . . . . . . . . 35
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 37
































Contreras, et al.        Expires January 9, 2014                [Page 3]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


1.  Introduction

   The base solution describing how continuous multicast service
   delivery can be provided in Proxy Mobile IPv6 (PMIPv6) domains is
   described in [RFC6224].  It specifies the basic functionality needed
   in the Proxy Mobile IPv6 [RFC5213] entities to provide a multicast
   service, so continuous delivery of multicast traffic is supported by
   obtaining, after each handover, the on-going multicast subscription
   information directly from the Mobile Node (MN).  When a mobile node
   attaches to a new Mobile Access Gateway (MAG), the mobile node is
   queried by the mobile access gateway through a Multicast Listener
   Discovery (MLD) General Query, which is sent just after any new link
   is set up, to get knowledge of any existing subscription, as
   specified in [RFC2710].

   However, the base solution needs to be improved to meet some
   performance requirements [I-D.von-hugo-multimob-future-work],
   especially those referred to the user perceived service quality,
   which is seriously affected by the disruption of multicast content
   forwarding to the mobile node during handovers.

   A mobile node with an active multicast subscription, moving from one
   point of attachment to another within a Proxy Mobile IPv6 domain,
   experiences a certain delay until it resumes receiving again the
   multicast content that it was receiving at the previous location.
   Such delay causes a gap in the content reception.  Two different
   actions can help mitigating such reception gap.  One of them is to
   buffer at the previous mobile access gateway a copy of the multicast
   traffic destined to the mobile node and forward it to the new mobile
   access gateway, in order to deliver that traffic to the mobile node.
   The other possible (complementary) action is to reduce the time
   needed by the new mobile access gateway to get knowledge of the
   active multicast subscription of the mobile node (i.e., the multicast
   context), so the new mobile access gateway can subscribe to the
   multicast group(s) on behalf of the mobile node as soon as possible.

   While the first mechanism could potentially be accomplished by using
   some adaptation of [RFC5949] to multicast traffic (despite being only
   applicable in the case the underlying radio access technology
   supports layer-2 triggers, thus requiring additional support on the
   mobile node), there is no generic standard solution for the
   accelerated acquisition of the on-going multicast subscription of the
   mobile node.

   The approach followed by the base solution [RFC6224] to get knowledge
   of an existing multicast subscription relies on the behavior of the
   IGMP/MLD protocols.  Both protocols send multicast membership query
   messages when a new link is up.  The response to such a message



Contreras, et al.        Expires January 9, 2014                [Page 4]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   reports any existing multicast subscription by the mobile node.
   While this is a straightforward approach, the mobile access gateway
   can incur in a non-negligible delay in receiving the corresponding
   MLD Report message.  This delay is caused by the time needed for the
   detection of the attachment in the new link and the re-establishment
   of the data plane after the handover, the radio transfer delays
   associated with the signaling to the mobile node, and the MLD query
   response interval time required by this procedure (whose default
   value is 10 seconds as defined in [RFC2710], or between 5 and 10
   seconds as considered in the best case wireless link scenario in
   [RFC6636]).

   This document extends the Proxy Mobile IPv6 signaling protocol
   defined in the base protocol [RFC5213] by including a new multicast
   information option to update Proxy Mobile IPv6 entities during the
   registration and de-registration processes, and new messages to
   trigger the transfer of multicast information.  No extension is
   required in any of the multicast-related protocols in use (IGMP/MLD
   or PIM protocols).  Furthermore, this specification does not
   substitute the standard procedures defined in [RFC6224] (e.g., the
   mobile access gateway will continue sending an MLD Query to the
   entering MN as soon as the point-to-point link is set up), but
   complements them for accelerating the acquisition of the multicast
   content by the mobile access gateway associated to the new point-of-
   attachment.

   This document provides a signaling method internal to the network to
   speed up the subscription information acquisition by the mobile
   access gateway, in order to accelerate the multicast delivery to the
   mobile node after having completed a handover.  By doing so, the
   knowledge by the mobile access gateway of the currently active
   multicast subscription becomes independent of the underlying radio
   technology dynamics and relaxes the requirement of a rapid response
   from the mobile node in processing IGMP/MLD control messages.  Issues
   like radio framing, radio access contention, channel reliability,
   MN's capabilities (i.e., layer-2 triggering support), IGMP/MLD timers
   optimization for wireless environments, etc, will not impact on the
   observed multicast performance during handovers.

   The solution described in this document can also be applied to the
   solutions described in [I-D.ietf-multimob-pmipv6-ropt].  Furthermore,
   it is also independent of the role played by the mobile access
   gateway within the multicast network (either acting as MLD proxy or
   multicast router).







Contreras, et al.        Expires January 9, 2014                [Page 5]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


1.1.  Handover optimization requirements

   A basic solution for providing support of multicast in a network-
   based mobility management environment has been specified in [RFC6224]
   without introducing changes on the original PMIPv6 specification
   [RFC5213].  The focus of the present specification is on improving
   the efficiency of the base solution regarding handover performance.

   One of the critical aspects of the base solution is the expected
   delay incurred by the mobile access gateway (where the mobile node is
   being attached to) to be informed about the on-going multicast
   subscription of the entering MN, mainly due to the fact that the
   mechanisms provided in the base solution relay on the original MLD
   procedures, with long timing interactions not conceived for mobile
   environments.  Then, the requirements to be covered by a handover
   optimization solution can be established in the following manner:

   o  The solution must be applicable to any kind of MN, in such a way
      that any type of mobile node in a PMIPv6 domain being served with
      multicast traffic can benefit from the optimized solution.

   o  The solution should be integrated as part of the PMIPv6 suite of
      protocols to ensure a smooth introduction of the new functionality
      in the network.

   o  The solution must not impact on existing multicast protocols.

   o  The solution must optimize the handover performance respect to the
      performance achieved with the base solution for any kind of
      handover process (i.e., for proactive and reactive handovers).

   o  The solution should minimize the number and extent of additional
      support required in the network, aiming at an easier deployment.

   The present specification addresses all these requirements, as
   described in the following sections.


2.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC2119 [RFC2119].

   This document uses the terminology referring to PMIPv6 components as
   defined in [RFC5213].

   Additionally, the following terms are defined and used in this



Contreras, et al.        Expires January 9, 2014                [Page 6]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   document.

   pMAG:  The previous MAG or pMAG is the mobile access gateway where
      the MN was initially registered in a handover event.

   nMAG:  The new MAG or nMAG is the mobile access gateway where the MN
      is registered at the end of the handover event.

   Reactive Handover:  A reactive handover is a handover event in which
      the Local Mobility Anchor (LMA) receives the mobile node
      registration from the nMAG without having previously received the
      MN de-registration from the pMAG.

   Proactive handover:  A proactive handover is a handover event where
      the mobile node is firstly de-registered on the local mobility
      anchor by the pMAG, and later on it is registered by the nMAG as
      consequence of changing the point of attachment.

   Multicast Membership Context:  Along this document, multicast
      membership context makes reference to the information relative to
      the currently active multicast subscription of an MN in a handover
      event which is transferred between the PMIPv6 entities to support
      the handover optimization.


3.  Overview

   The local mobility anchor is a key element within the PMIPv6
   infrastructure, which traces the mobile node reachability along the
   PMIPv6 domain.  Therefore the LMA is the best element to maintain the
   MNs' multicast subscription information up-to-date and to forward it
   to the rest of PMIPv6 entities (i.e., to the mobility access
   gateways) as needed when MNs move within the domain.  The LMA has
   timely knowledge of the MNs' location, especially during handover
   events, and it is therefore able to quickly provide information to
   the new point of attachment (e.g., by querying the previous one).
   Figure 1 summarizes the main idea of the optimization.














Contreras, et al.        Expires January 9, 2014                [Page 7]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


                                       +------+
                                       | pMAG |   |
                                       +------+   |
                                      /           |
                                     /            |
                                    /             |
                                   /              |
            -*-*-*-*-             /              (MN)
           (         )           /                |
          (           )   +-----+      +------+   |
         (  Internet   )--| LMA |------| nMAG |   v
          (           )   +-----+      +------+
           (         )
            -*-*-*-*-          Registration
                             <--------------

                            Registration Ack
                          & Multicast Context
                             -------------->

             Figure 1: High level description of the solution

   The local mobility anchor only obtains the detailed subscription
   information or multicast context during a handover event.  There is
   no need of continuously informing the LMA about MNs' multicast state
   while the mobile nodes remain attached to the same mobile access
   gateway.  Such a continuous updating procedure would significantly
   increase the signaling load within the PMIPv6 domain without a clear
   benefit.  The multicast context is only critical during handovers,
   neither after nor before.  Indicating the active subscription while
   the handover is ongoing guarantees that such information will be up-
   to-date and ready to be transferred to the new MAG where the mobile
   node has just attached.

   To be able to transfer the multicast subscription information between
   Proxy Mobile IPv6 entities during a handover, this document extends
   the PMIPv6 protocol in several ways.  First of all, a new mobility
   option is defined to carry the multicast context of the current
   subscription.  Furthermore, additional messages are defined to manage
   the interchange of the multicast information among PMIPv6 entities.
   Finally, some flags are defined to govern the process.


4.  Proxy Mobile IPv6 extensions

   This section outlines the extensions proposed to the PMIPv6 protocol
   specified in [RFC5213].




Contreras, et al.        Expires January 9, 2014                [Page 8]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


4.1.  Active Multicast Subscription mobility option

4.1.1.  Option application rules

   A new TLV-encoded mobility option, "Active Multicast Subscription"
   option is defined for use with the PBU (Proxy Binding Update) and PBA
   (Proxy Binding Acknowledge) messages exchanged between a local
   mobility anchor and a mobility access gateway to transfer the
   multicast subscription information.  This option is used for
   exchanging the multicast membership context.  This information is
   carried by directly using the format defined in the original MLD
   specifications.  There can be multiple "Active Multicast
   Subscription" options present in the message, one for each active
   subscription maintained by the mobile node when the handover is
   taking place (i.e., one per multicast membership context).

   This new option is also used for the same purposes by the new
   Subscription Response message defined later in this document.

   MLDv2 is the primary objective for the definition of the option
   format.  MLDv1 is also considered for backward compatibility.

4.1.2.  Option format

   The format of this new option is as follows:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
                      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                      |      Type     |     Length    |    MLD Type   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                                                               |
      +                  Multicast Membership Context                 +
      |                                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The alignment requirement of this option is 8n+1.

   Type:

      To be defined by IANA {IANA-1}, for indication of an IPv6 Active
      Multicast Subscription option.

   Length:

      8-bit unsigned integer indicating the length of the option in
      octects, excluding the type and length fields.




Contreras, et al.        Expires January 9, 2014                [Page 9]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   MLD type:

      Field used to identify the IPv6 multicast membership protocol in
      use, and the corresponding format of the next Multicast Membership
      Context information field.  This field maps the type codification
      used in the original MLD specifications for the Report message.
      For MLDv2, the MLD Type value is 0x143.

   Multicast Membership Context:

      Multicast subscription information corresponding to a single
      subscribed multicast address.  For MLDv2, the format of this field
      follows the Multicast Address Record format as defined in
      [RFC3810].

4.1.3.  Backward compatibility with MLDv1

   The following values are adopted when MLDv1 is used.

   MLD type:

      For MLDv1, the MLD Type value is 0x131.

   Multicast Membership Context:

      For MLDv1, the relevant information for multicast context is
      simply given, according to [RFC2710], by the multicast address of
      the subscribed content.

      In consequence, the Multicast Membership Context is defined as a
      4-octect reserved field and the Multicast Address of the
      subscribed content as in [RFC2710], in the following manner:


        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                           Reserved                            |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                                                               |
       *                                                               *
       |                                                               |
       *                       Multicast Address                       *
       |                                                               |
       *                                                               *
       |                                                               |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+




Contreras, et al.        Expires January 9, 2014               [Page 10]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


4.2.  Multicast Signaling flag on PBU/PBA message headers

4.2.1.  Flag application rules

   A new flag S {IANA-2} is added in both PBU and PBA message headers to
   advise about the mobile access gateway and the local mobility anchor
   capabilities of processing multicast- related signaling for the MN
   that caused the message.

   This flag governs the multicast-related signaling between the LMA and
   the MAG.  As a general rule, the value of the flag in the PBA message
   SHOULD be a copy of the value received in the PBU message.  Specific
   rules are described in next sub-sections.

4.2.1.1.  Registration process

   During handover, the entities involved in this process are the nMAG
   and the LMA.  These rules also apply for the Initial Binding
   registration process.

   o  PBU message

      *  S=0, it indicates that the MAG sending the PBU message does not
         accept multicast-related signaling for the MN being attached.
         This can be used to discriminate PMIPv6 nodes which are not
         multicast enabled, for backward compatibility reasons.

      *  S=1, it indicates that the MAG sending the PBU message accepts
         multicast-related signaling for the MN being attached.
         Depending on the type of handover (reactive or proactive) the
         LMA will take some actions, described later in this document.

   o  PBA message

      *  If S=0 in the corresponding PBU message, the value of the flag
         in the PBA message MUST be a copy of the value received in the
         PBU message (thus S=0), without any further meaning.

      *  If S=1 in the corresponding PBU message, two sub-cases can
         happen

         +  S=1 and "Active Multicast Subscription" mobility option in
            the PBA message.  When the MN maintains an active multicast
            session, if the LMA is able to provide the multicast
            subscription information during registration, the PBA
            message SHOULD include the "Active Multicast Subscription"
            mobility option.  If the LMA is not able to provide such
            information during registration, the PBA message SHOULD NOT



Contreras, et al.        Expires January 9, 2014               [Page 11]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


            include the "Active Multicast Subscription" mobility option.
            This case is useful to decouple unicast and multicast
            signaling for an MN being registered at nMAG.  A way for
            obtaining later active multicast-subscription information is
            described later in this document.

         +  S=0 in the PBA message if the MN does not maintain an active
            multicast subscription (note that for backward compatibility
            reasons an LMA not supporting multicast related signaling
            would always send S=0).

4.2.1.2.  De-registration process

   During handover, the entities involved in this process are the pMAG
   and the LMA.  These rules apply for the Binding De-registration
   process

   o  PBU message

      *  S=0, it indicates that the MN has no active multicast session
         (note that for backward compatibility reasons a pMAG not
         supporting multicast related signaling would always send S=0).

      *  S=1, it indicates that the MN has an active multicast session,
         and the multicast context MUST be transported in the "Active
         Multicast Subscription" mobility option.

   o  PBA message

      *  The value of the flag in the PBA message SHOULD be 0, without
         any further meaning (note that for backward compatibility
         reasons an LMA not supporting multicast related signaling would
         always send S=0).

4.2.2.  New format of conventional PBU/PBA messages

4.2.2.1.  Proxy Binding Update message

   As result of the new defined flag, the PBU message results as
   follows:











Contreras, et al.        Expires January 9, 2014               [Page 12]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
                                     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                                     |           Sequence #          |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |A|H|L|K|M|R|P|S|   Reserved    |            Lifetime           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     .                                                               .
     .                          Mobility options                     .
     .                                                               .
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

4.2.2.2.  Proxy Binding Acknowledgement Message

   As result of the new defined flag, the PBA message results as
   follows:

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
                                     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                                     |    Status     |K|R|P|S| Rsrvd |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |           Sequence #          |           Lifetime            |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     .                                                               .
     .                        Mobility options                       .
     .                                                               .
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

4.3.  Messages for active multicast subscription query

   A new pair of messages is defined for querying entities about the
   active multicast subscription of the MN when the handover is of
   reactive type.

   These messages are sent using the Mobility Header as defined in
   [RFC6275].

4.3.1.  Subscription Query message

4.3.1.1.  Message application rules

   The Subscription Query message {IANA-3} is sent by the LMA towards
   the pMAG to query it about any existing multicast subscriptions of



Contreras, et al.        Expires January 9, 2014               [Page 13]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   the MN which is being registered by the nMAG.  This message is
   generated in case that the handover is of reactive type.

   Additionally, this message is sent by the nMAG towards the LMA to
   query it about the existing multicast subscriptions of the MN when
   the LMA acknowledges the PBU sent by the nMAG but the multicast
   context is not provided (in detail, when the PBU message has set the
   flag S to 1, and the PBA message has set the flag S to 1 but the
   multicast context is missing).

4.3.1.2.  Message format

   The Subscription Query message has the following format.

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
                                     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                                     |  Sequence #   |   Reserved    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     .                                                               .
     .                        Mobility options                       .
     .                                                               .
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Sequence Number:

      The Sequence Number field establishes the order of the messages
      sent in the Subscription Query / Subscription Response dialogue
      between the LMA and the MAG for a certain MN.  The initial
      Sequence Number MUST be determined by the entity which creates the
      message (either LMA or MAG, depending on the scenario), which will
      be responsible of managing this counter.

   Reserved:

      This field is unused for now.  The value MUST be initialized to 0.

   Mobility options:

      This message will carry one or more TLV-encoded mobility options.
      The valid mobility options for this message are the following:

      *  Mobile Node Identifier option (mandatory)

      *  Home Network Prefix option (optional)




Contreras, et al.        Expires January 9, 2014               [Page 14]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


      There can be one or more instances of the Home Network Prefix
      option, but only one instance of the Mobile Node Identifier
      option.

4.3.2.  Subscription Response message

4.3.2.1.  Message application rules

   The Subscription Response message {IANA-4} is sent by the pMAG
   towards the LMA, or by the LMA towards the nMAG, to answer a
   previously received Subscription Query message, as described above.

4.3.2.2.  Message format

   The Subscription Response message has the following format.

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
                                     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                                     |  Sequence #   |I|  Reserved   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
     .                                                               .
     .                        Mobility options                       .
     .                                                               .
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Sequence Number:

      The value of the Sequence Number field in the Subscriber Response
      message MUST be a copy of the Sequence Number received in the
      Subscription Query message.

   Multicast Information (I):

      The multicast Information flag I {IANA-5} specifies if there is
      multicast subscription information available for the MN or not.
      The meaning is the following:

         I=0: there is no multicast subscription information available
         for the MN identified by the Mobile Node Identifier option in
         this message.

         I=1: there is multicast subscription information available for
         the MN identified by the Mobile Node Identifier option in this
         message.  The multicast subscription information MUST be
         carried on one or more instances of the Active Multicast



Contreras, et al.        Expires January 9, 2014               [Page 15]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


         Subscription option in this message (one instance for each
         active subscription).

   Reserved:

      This field is unused for now.  The value MUST be initialized to 0.

   Mobility options:

      This message will carry one or more TLV-encoded mobility options.
      The valid mobility options for this message are the following:

      *  Mobile Node Identifier option (mandatory)

      *  Active Multicast Subscription option (mandatory) only when flag
         I=1; it MUST NOT be present in any other case

      *  Home Network Prefix option (optional)

      There can be one or more instances of the Home Network Prefix
      option (in all cases) and the Active Multicast Subscription option
      (only when I=1), but only one instance of the Mobile Node
      Identifier option.

4.4.  New PBA timer in the LMA

   A new timer named "PBA timer" is used in the LMA to define the
   maximum waiting time before the PBA message is sent to the nMAG in
   case the multicast subscription information relative to the MN is not
   yet available.  The aim of this timer is to prevent potential large
   delays in the forwarding of unicast traffic towards the MN being
   registered at the nMAG.  This timer allows decoupling the unicast
   signaling from the multicast one.

   This timer SHOULD be upper bounded by the constant defined in
   [RFC6275] INIT_BINDACK_TIMEOUT, whose default value is 1 s.  This
   constant sets the time when the nMAG will retry the MN registration
   by sending again the PBU message.  The "PBA timer" has to be set to a
   value that ensures that the nMAG does not enter the retry mode.


5.  Handover signaling procedures

   As the MN moves from one access gateway to another, the mobility-
   related signaling due to the handover event is carried out
   independently by the pMAG and the nMAG.  That signaling process is
   not synchronized and, thus, two scenarios need to be considered
   depending on the order in which the LMA receives notification of the



Contreras, et al.        Expires January 9, 2014               [Page 16]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   MN registration and de-registration in the nMAG and the pMAG
   respectively.

5.1.  Handover of proactive type

5.1.1.  Rationale

   In the proactive case, the MN is firstly de-registered by the pMAG,
   and later on it is registered by the nMAG as consequence of changing
   the point of attachment.

   Only for those MNs which maintain an active multicast subscription,
   the pMAG includes the "Active Multicast Subscription" mobility option
   carrying the multicast context of the MN at that moment as part of
   the PBU message (with flag S set to 1).

   The local mobility anchor will store that information in the
   corresponding binding cache.  If, later on, the MN attaches to a
   nMAG, this information is sent (using the same TLV option) to the
   nMAG as part of the PBA confirmation of the registration process (the
   PBU message sent by the nMAG SHOULD set the flag S to 1).  On the
   other hand, if no further registration happens, the multicast
   information is removed together with the rest of binding database for
   that MN.

   After receiving the multicast context, the nMAG can subscribe to the
   multicast flow(s) on behalf of the MN in case there is no other MN
   already receiving it at the nMAG.  The multicast status can be also
   set in advance for the point-to-point link towards the MN.

   Note that the solution described here does not prevent benefiting
   from extended support in the mobile node/network that facilitates the
   proactive mode operation of the solution, e.g., based on layer-2
   capabilities.

5.1.2.  Message flow description

   Figure 2 summarizes this process.













Contreras, et al.        Expires January 9, 2014               [Page 17]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


          +-----+          +----+           +-----+          +----+
          | MN  |          |pMAG|           | LMA |          |nMAG|
          +-----+          +----+           +-----+          +----+
             |                |                |                |
             |                |==Bi-Dir Tunnel=|                |
             | Multicast Data |                |                |
             |<---------------|                |                |
             |                |                |                |
      1) MN Detached          |                |                |
             |         MN Detached Event       |                |
             |                |                |                |
             |                |Ext'd DeReg PBU |                |
      2)     |                |--------------->|                |
             |                |                |                |
      3)     |                |            Accept PBU           |
             |                |(Multicast Subscription info stored)
             |                |                |                |
             |                |      PBA       |                |
      4)     |                |<---------------|                |
             |                |                |                |
      5) MN Attached          |                |                |
             |                |                |   MN Attached Event
             |                |                |                |
             |                |                |       PBU      |
      6)     |                |                |<---------------|
             |                |                |                |
             |                |                |   Ext'd PBA    |
      7)     |                |                |--------------->|
             |                |                |                |
      8)     |                |                |          Accept PBA,
             |                |                |   Multicast Group join
             |                |                | and P-t-P status setup
             |                |                |                |
             |                |                |==Bi-Dir Tunnel=|
             |                |                |                |
             |                |                | Multicast Data |
             |<-------------------------------------------------|
             |                |                |                |
             |                |                |                |

                       Figure 2: Proactive handover

   The message flow is as follows:

   1.  A registered MN is receiving a multicast content which has been
       previously subscribed to by sending a standard MLD report from
       the mobile node to the currently serving mobile access gateway,
       pMAG.  The pMAG keeps the multicast status state of the point-to-



Contreras, et al.        Expires January 9, 2014               [Page 18]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


       point link with the MN.

   2.  The MN initiates a handover process (e.g. because of better radio
       conditions) over a radio access controlled by a new MAG.  As a
       consequence, pMAG determines a detach event corresponding to this
       mobile node, and updates the attachment status of this MN to the
       local mobility anchor by sending an extended Proxy Binding Update
       message, including the "Active Multicast Subscription", which
       contains the multicast context of the active multicast
       subscriptions in the moment of handover.

   3.  The LMA processes the PBU message.  Additionally, the LMA stores
       in the Binding Cache the information regarding the on-going
       multicast subscription(s) when the detachment is initiated.  This
       information is kept until a new registration of the MN is
       completed by another MAG, or until the Binding Cache expiration,
       according to [RFC5213].

   4.  The local mobility anchor acknowledges to the pMAG the previous
       PBU message.

   5.  As a result of the handover process, the mobile node attaches to
       another mobility access gateway, called nMAG.

   6.  The nMAG triggers a registration process by sending a PBU message
       (with flag S set to 1) to the local mobility anchor.

   7.  After the analysis of the PBU message, the LMA sends an extended
       PBA including the "Active Multicast Subscription" option, which
       contains the multicast context of the active subscriptions in the
       moment of handover.

   8.  The nMAG processes the PBA message following all the standard
       procedures described in [RFC5213].  Additionally, with the new
       information relative to multicast subscription, the nMAG sets up
       the multicast status of the point-to-point link between the nMAG
       and the MN, and joins the content identified by (S,G) on behalf
       of the MN in case the nMAG is not receiving already such content
       due to a previous subscription ordered by another MN attached to
       it.  From that instant, the multicast content is served to the
       MN.

5.2.  Handover of reactive type

5.2.1.  Rationale

   In the reactive case, the LMA receives the mobile node registration
   from the nMAG without having previously received the MN de-



Contreras, et al.        Expires January 9, 2014               [Page 19]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   registration from the pMAG.

   As the nMAG is not aware of any active multicast subscription of the
   mobile node, the nMAG will start a conventional registration process,
   by sending a normal PBU message (with flag S set to 1) towards the
   local mobility anchor.

   In the reactive handover case, after MN registration at the nMAG, the
   local mobility anchor SHOULD generically query the pMAG for
   retrieving the multicast context of the on-going multicast
   subscription of the mobile node.  However, the LMA may know in
   advance if the pMAG supports multicast signaling based on the value
   of the flag S received during the MN registration in pMAG.
   Specifically, in case the pMAG does not support multicast signaling
   (e.g., the S flag value received from pMAG at the time of registering
   the mobile node was 0), the LMA MAY decide not to query pMAG even in
   the case of receiving an nMAG indication of supporting multicast
   signaling.

   Once the multicast subscription information is retrieved from the
   pMAG, the LMA encapsulates it in the PBA message by using the TLV
   option "Active Multicast Subscription", and forwards the PBA message
   to the nMAG.  Then, the nMAG can subscribe the multicast flow on
   behalf of the MN, if there is no other mobile node receiving it
   already at the nMAG.  The multicast status can be also set in advance
   for the point- to-point link towards the mobile node.

5.2.2.  Message flow description

   Figure 3 summarize this process.





















Contreras, et al.        Expires January 9, 2014               [Page 20]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


       +-----+          +----+           +-----+          +----+
       | MN  |          |pMAG|           | LMA |          |nMAG|
       +-----+          +----+           +-----+          +----+
          |                |                |                |
          |                |                |         MN Attached Event
          |                |                |                |
          |                |                |       PBU      |
   1)     |                |                |<---------------|
          |                |                |                |
          |                |  Subscr Query  |                |
   2)     |                |<---------------|                |
          |                |                |                |
          |                |  Subscr Resp   |                |
   3)     |                |--------------->|                |
          |                |                |                |
          |                |    (Multicast Subscription      |
          |                |        info forwarding)         |
          |                |                |                |
          |                |                |   Ext'd PBA    |
   4)     |                |                |--------------->|
          |                |                |                |
   5)     |                |                |           Accept PBA,
          |                |                |      Multicast Group join
          |                |                |     and P-t-P status setup
          |                |                |                |
          |                |                |==Bi-Dir Tunnel=|
          |                |                |                |
          |                |                |   (S,G) Data   |
          |<-------------------------------------------------|
          |                |                |                |
          |                |                |                |

                        Figure 3: Reactive handover

   We next take as starting point the situation where an MN is attached
   to the pMAG, being multicast-enabled and maintaining an active
   multicast subscription at this moment.

   The sequence of messages for the handover of the mobile node is the
   following (as depicted in Figure 3):

   1.  At certain time, the MN initiates a handover process (e.g.
       because of better radio conditions) over a radio access
       controlled by a new MAG.  Then, the nMAG triggers a registration
       process by sending a PBU message (with flag S set to 1) to the
       local mobility anchor.  As it is a reactive case, the pMAG is not
       aware of the detachment process.




Contreras, et al.        Expires January 9, 2014               [Page 21]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   2.  Prior to acknowledge the received PBU message, the LMA queries
       the pMAG about if there is any active multicast subscription for
       the MN, by sending a Subscription Query message.

   3.  The pMAG answers the LMA with a Subscription Response message
       including the multicast context of the existing subscriptions.

   4.  After processing the pMAG answer, the LMA acknowledges (with flag
       S set to 1) the PBU message, including the multicast subscription
       information within the "Active Multicast Subscription" option.
       The nMAG then processes the extended PBA message.

   5.  The nMAG processes the PBA message, and it proceeds to set up the
       multicast status of the point-to-point link between the nMAG and
       the mobile node, and to join the content identified by (S,G) on
       behalf of the MN in case the nMAG is not receiving already such
       content.  (The bidirectional tunnel is also set up between the
       nMAG and the local mobility anchor if it has not been established
       before by another MN connection).  At this moment, the multicast
       content can be served to the MN.  The unicast traffic for the
       mobile node can be forwarded as well.

5.2.3.  Further considerations for the reactive handover signaling

   A handover event is managed independently by the pMAG and nMAG.  It
   is not a synchronized process.  In a reactive handover, the LMA
   receives a registration PBU from nMAG before a de-registration PBU is
   received from pMAG.

   In the message flows detailed above, it could be the case that the
   LMA receives a de-registration PBU from pMAG just after sending the
   Subscription Query message, but before receiving the Subscription
   Response message.  That de-registration PBU message from pMAG carries
   the multicast subscription information required to assist the MN in
   the handover, so such valuable information SHOULD be kept by the LMA.
   Furthermore, it is possible that once the Subscription Query message
   arrives to pMAG, the pMAG could have already removed the multicast
   related information for the MN.

   In order to avoid losing the multicast subscription information sent
   in the de-registration PBU message, the local mobility anchor SHOULD
   store it, and SHOULD include it in the PBA message towards the nMAG
   in case the Subscription Response message from the pMAG does not
   contain multicast subscription information for the mobile node.







Contreras, et al.        Expires January 9, 2014               [Page 22]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


5.3.  Prevention of large delays of the binding acknowledgement for
      unicast traffic

   According to the message sequences described for the reactive
   handover case, in case the LMA has to request the multicast
   subscription information from the pMAG, the binding request sent by
   the nMAG is maintained on-hold until the local mobility anchor
   receives, processes and includes the multicast subscription
   information into the extended PBA message.  As consequence, the
   unicast traffic may then suffer an extra delay motivated by the
   multicast-related signaling.  During that time, the unicast traffic
   with destination the MN being registered by the nMAG MAY be buffered
   by the local mobility anchor.

   In order to avoid any potential large delay in the forwarding of
   unicast traffic arriving at the LMA towards the MN, a mechanism
   SHOULD be implemented to decouple multicast from unicast traffic
   reception by the MN.

   Figure 4 shows this mechanism































Contreras, et al.        Expires January 9, 2014               [Page 23]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


       +-----+          +----+           +-----+          +----+
       | MN  |          |pMAG|           | LMA |          |nMAG|
       +-----+          +----+           +-----+          +----+
   1)     |                |==Bi-Dir Tunnel=|                |
          |  unicast data  |                |                |
          |<-v-v-v-v-v-v-v-|                |                |
          |                |                |                |
          | Multicast Data |                |                |
          |<---------------|                |                |
          |                |                |        MN Attached Event
          |                |                |       PBU      |
   2)     |                |                |<---------------|
          |                |  Subscr Query  |                |
   3)     |                |<---------------|                |
          |                |                |                |
   4)     |                |       <PBA timer starts>        |
          |                |               ///               |
          |                |               ///               |
   5)     |                |       <PBA timer expires>       |
          |                |                |                |
          |                |                |   Ext'd PBA    |
          |                |                |--------------->|
          |                |                |                |
          |                |                |          Accept PBA
          |                |                |                |
          |                |                |==Bi-Dir Tunnel=|
          |                |                |                |
          |                |                |  Unicast Data  |
          |<-v-v-v-v-v-v-v-v-v-v-v-v-v-v-v-v-v-v-v-v-v-v-v-v-|
          |                |                |                |
          |                |                |  Subscr Query  |
   6)     |                |                |<---------------|
          |                |  Subscr Resp   |                |
   7)     |                |--------------->|                |
          |                |                |                |
          |                |    (Multicast Subscription      |
          |                |        info forwarding)         |
          |                |                |                |
          |                |                |  Subscr Resp   |
   8)     |                |                |--------------->|
          |                |                |                |
          |                |                |   Multicast Group join
          |                |                | and P-t-P status setup
          |                | Multicast Data |                |
          |<-------------------------------------------------|
          |                |                |                |

          Figure 4: Decoupling of unicast and multicast signaling



Contreras, et al.        Expires January 9, 2014               [Page 24]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   The sequence of messages is the following:

   1.  An MN is attached to the pMAG.  The MN is a multicast-enabled
       node, and it is receiving both unicast and multicast traffic
       simultaneously.

   2.  Some time later, The MN initiates a handover process (e.g.
       because of better radio conditions) over a radio access
       controlled by a new mobile access gateway.  Then, the nMAG
       triggers a registration process by sending a PBU message (with
       flag S set to 1) to the local mobility anchor.  As it is a
       reactive case, the pMAG is not aware of the detachment process.

   3.  Prior to acknowledge the received PBU message, the LMA decides to
       query the pMAG about if there is any active multicast
       subscription for the mobile node, by sending a Subscription Query
       message.

   4.  Immediately after sending the Subscription Query message, the LMA
       starts the timer "PBA timer", which determines the maximum
       waiting time before the PBA is sent to avoid any potential large
       delay in the forwarding of unicast traffic towards the MN.

   5.  In case the "PBA timer" expires, the LMA acknowledges the PBU
       message, by sending the PBA message with flag S=1, without the
       multicast context information.  The nMAG then processes the
       extended PBA message.  Such acknowledgement will allow the mobile
       node to receive the unicast traffic from that time on.  The
       bidirectional tunnel is also set up between the nMAG and the LMA
       if it has not been established before.

   6.  In parallel, the nMAG sends a Subscription Query message to the
       LMA requesting the multicast-subscription details yet unknown for
       the mobile node.

   7.  The pMAG answers the Subscription Query message originally sent
       by the local mobility anchor, including the multicast context.

   8.  After processing the pMAG answer, the LMA sends a Subscription
       Response message to the nMAG, including the multicast
       subscription information within the "Active Multicast
       Subscription" option.  The nMAG processes the PBA message, and it
       proceeds to set up the multicast status of the point-to-point
       link between the nMAG and the mobile node, and to join the
       content identified by (S,G) on behalf of the MN in case the nMAG
       is not receiving already such content.  The bidirectional tunnel
       is also set up between the nMAG and the LMA if it has not been
       established before.  At this moment, the multicast content can



Contreras, et al.        Expires January 9, 2014               [Page 25]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


       also be served to the mobile node.


6.  IPv4 support

   IPv4-based mobile nodes (being either IPv4/IPv6 dual-stack, or IPv4-
   only enabled) can be supported in a PMIPv6 domain according to
   [RFC5844].  When referring to multicast membership protocols and
   procedures, this means that IGMP functionality has to be also
   supported between the PMIPv6 entities, as documented in [RFC6224], to
   allow the mobile access gateway requesting multicast contents to the
   mobility anchor on behalf of the mobiles nodes attached to it.

6.1.  Active Multicast Subscription for IPv4

   The Active Multicast Subscription option defined in Section 4.1,
   which transports the multicast membership context of the mobile node
   during handover, should be compatible with IGMP-based formats.
   Specifically, the option format is defined for IPv4-based MNs as
   follows:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
                      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                      |      Type     |     Length    |   IGMP Type   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                                                               |
      +                  Multicast Membership Context                 +
      |                                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   IGMPv3 is the primary objective for the definition of the option
   format.  IGMPv1 and IGMPv2 are also considered for backward
   compatibility.  The alignment requirement of this option is 4n+1.

   Type:

      To be defined by IANA {IANA-6}, for indication of an IPv4 Active
      Multicast Subscription option.

   Length:

      8-bit unsigned integer indicating the length of the option in
      octects, excluding the type and length fields.

   IGMP type:




Contreras, et al.        Expires January 9, 2014               [Page 26]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


      Field used to identify the IPv4 multicast membership protocol in
      use, and the corresponding format of the next Multicast Membership
      Context information field.  This field maps the type codification
      used in the original IGMP specifications for the Report message.

      0x12: Use of IGMPv1 multicast membership protocol.

      0x16: Use of IGMPv2 multicast membership protocol.

      0x22: Use of IGMPv3 multicast membership protocol.

   Multicast Membership Context:

      Multicast subscription information corresponding to a single
      subscribed multicast address.  Depending on the IGMP version being
      used by the mobile node, the format of the Multicast Context could
      follow the following formats:

      *  For IGMPv1, the Group Address format as defined in [RFC1112].

      *  For IGMPv2, the Group Address format as defined in [RFC2236].

      *  For IGMPv3, the Group Record format as defined in [RFC3376].

6.2.  Signaling procedures for IPv4 support

   Generic signaling procedures for the support of IPv4 in PMIPv6
   domains have been already specified in [RFC5844].  In order to
   prevent errors while signaling the on-going multicast subscription
   for a mobile node during the handover process, the following
   extensions have to be considered.

   o  If the registration / de-registration process in a handover is for
      an IPv6-only MN, and the type of the received Active Multicast
      Subscription option indicates IPv4, then the multicast membership
      context received MUST be silently discarded.

   o  If the registration / de-registration process in a handover is for
      an IPv4-only MN, and the type of the received Active Multicast
      Subscription option indicates IPv6, then the multicast membership
      context received MUST be silently discarded.

   o  If the registration / de-registration process in a handover is for
      a dual stack MN, the received Active Multicast Subscription option
      (or options) MUST be accepted independently of the type
      indication.





Contreras, et al.        Expires January 9, 2014               [Page 27]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


6.3.  Binding Cache extensions for IPv4 support

   Additionally, since the membership information is temporally stored
   in the mobility anchor under some circumstances (e.g., proactive
   handover), the Binding Cache entry for an IPv4-based multicast-
   enabled MN should be extended for storing the IGMP-based context
   formats mentioned above, including the IGMP version indicator.


7.  Co-existence with PMIPv6 multicast architectural evolutions

   Along this document, it has been considered that the LMA entity is in
   charge of delivering both unicast and multicast traffic to a certain
   mobile node through the bi-directional tunnels connecting to the
   mobile access gateway where the MN is attached, as specified in the
   base solution defined in [RFC6224].  However, the solution described
   in this document can be also applied to other solutions where the
   multicast content is served from other entities in the PMIPv6 domain,
   as in the solution described in [I-D.ietf-multimob-pmipv6-ropt] to
   solve the tunnel convergence problem.

   The transfer of the multicast context will pass through the local
   mobility anchor, as described here.  However, the nMAG will subscribe
   to the multicast content through the node in charge of distributing
   multicast according to the adopted solution for multicast
   distribution in the PMIPv6 domain.


8.  Security Considerations

   This proposal does not pose any additional security threats to those
   already identified in [RFC5213].  All the security considerations in
   [RFC5213] are directly applicable to this protocol.  The signaling
   messages, Proxy Binding Update, and Proxy Binding Acknowledgement
   (extended with the new options defined in this document), the
   Subscription Query Message, and the Subscription Response Message
   exchanged between the mobile access gateway and the local mobility
   anchor, MUST be protected using end-to-end security association(s)
   offering integrity and data origin authentication.

   The mobile access gateway and the local mobility anchor MUST
   implement the IPsec security mechanism mandated by Proxy Mobile IPv6
   [RFC5213] tosecure the signaling described in this document.  In the
   following, we describe the Security Policy Database (SPD) and
   Security Association Database (SAD) entries necessary to protect the
   new signaling introduced by this specification (Subscription Query
   Message and Subscription Response Message).  We use the same format
   used by [RFC4877].  The SPD and SAD entries are only example



Contreras, et al.        Expires January 9, 2014               [Page 28]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   configurations.  A particular mobile access gateway implementation
   and a local mobility anchor home agent implementation could configure
   different SPD and SAD entries as long as they provide the required
   security of the signaling messages.

   For the examples described in this document, a mobile access gateway
   with address "mag_address_1", and a local mobility anchor with
   address "lma_address_1" are assumed.

      mobile access gateway SPD-S:
        - IF local_address = mag_address_1 &
             remote_address = lma_address_1 &
             proto = MH & (remote_mh_type = Subscription Query |
             local_mh_type = Subscription Response |
             remote_mh_type = Multicast Activity Indication Ack.|
             local_mh_type = Multicast Activity Indication)
          Then use SA1 (OUT) and SA2 (IN)

      mobile access gateway SAD:
        - SA1(OUT, spi_a, lma_address_1, ESP, TRANSPORT):
              local_address = mag_address_1 &
              remote_address = lma_address_1 &
              proto = MH
        - SA2(IN, spi_b, mag_address_1, ESP, TRANSPORT):
              local_address = lma_address_1 &
              remote_address = mag_address_1 &
              proto = MH

      local mobility anchor SPD-S:
        - IF local_address = lma_address_1 &
             remote_address =mag_address_1 &
             proto = MH & (remote_mh_type = Subscription Response |
             local_mh_type = Subscription Query |
             remote_mh_type = Multicast Activity Indication |
             local_mh_type = Multicast Activity Indication Ack.)
          Then use SA2 (OUT) and SA1 (IN)

      local mobility anchor SAD:
        - SA2(OUT, spi_b, mag_address_1, ESP, TRANSPORT):
              local_address = lma_address_1 &
              remote_address = mag_address_1 &
              proto = MH
        - SA1(IN, spi_a, lma_address_1, ESP, TRANSPORT):
              local_address = mag_address_1 &
              remote_address = lma_address_1 &
              proto = MH





Contreras, et al.        Expires January 9, 2014               [Page 29]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


9.  IANA Considerations

   This document defines the new following elements which values to be
   allocated by IANA:

   o  Mobility Header types: the Subscription Query {IANA-3} and
      Subscription Response {IANA-4} mobility header types.

   o  Mobility options: the Active Multicast Subscription mobility
      option for both IPv4 {IANA-6} and IPv6 {IANA-1} modes of
      operation.

   o  Flags: the multicast Signaling (S) {IANA-2} and the multicast
      Information (I) {IANA-5}.


10.  Contributors

   Dirk Von Hugo (Telekom Innovation Laboratories,
   Dirk.von-Hugo@telekom.de) extensively contributed to this document.


11.  Acknowledgments

   The authors would like to thank (in alphabetical order) Hitoshi
   Asaeda, Georgios Karagiannis, Marco Liebsch, Behcet Sarikaya, Thomas
   C. Schmidt and Stig Venaas for their valuable comments and
   discussions on the Multimob mailing list.  The authors are also
   grateful with Hitoshi Asaeda, Akbar Rahman, Behcet Sarikaya and Stig
   Venaas for their review of this document.

   The research of Carlos J. Bernardos leading to these results has
   received funding from the European Community's Seventh Framework
   Programme (FP7-ICT-2009-5) under grant agreement n. 258053 (MEDIEVAL
   project), being also partially supported by the Ministry of Science
   and Innovation (MICINN) of Spain under the QUARTET project (TIN2009-
   13992-C02-01).

   The research of Ignacio Soto has also received funding from the
   Spanish MICINN through the I-MOVING project (TEC2010-18907).


12.  References

12.1.  Normative References

   [RFC1112]  Deering, S., "Host extensions for IP multicasting", STD 5,
              RFC 1112, August 1989.



Contreras, et al.        Expires January 9, 2014               [Page 30]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2236]  Fenner, W., "Internet Group Management Protocol, Version
              2", RFC 2236, November 1997.

   [RFC2710]  Deering, S., Fenner, W., and B. Haberman, "Multicast
              Listener Discovery (MLD) for IPv6", RFC 2710,
              October 1999.

   [RFC3376]  Cain, B., Deering, S., Kouvelas, I., Fenner, B., and A.
              Thyagarajan, "Internet Group Management Protocol, Version
              3", RFC 3376, October 2002.

   [RFC4877]  Devarapalli, V. and F. Dupont, "Mobile IPv6 Operation with
              IKEv2 and the Revised IPsec Architecture", RFC 4877,
              April 2007.

   [RFC5213]  Gundavelli, S., Leung, K., Devarapalli, V., Chowdhury, K.,
              and B. Patil, "Proxy Mobile IPv6", RFC 5213, August 2008.

   [RFC5844]  Wakikawa, R. and S. Gundavelli, "IPv4 Support for Proxy
              Mobile IPv6", RFC 5844, May 2010.

   [RFC6275]  Perkins, C., Johnson, D., and J. Arkko, "Mobility Support
              in IPv6", RFC 6275, July 2011.

12.2.  Informative References

   [I-D.ietf-multimob-pmipv6-ropt]
              Zuniga, J., Contreras, L., Bernardos, C., Jeon, S., and Y.
              Kim, "Multicast Mobility Routing Optimizations for Proxy
              Mobile IPv6", draft-ietf-multimob-pmipv6-ropt-07 (work in
              progress), July 2013.

   [I-D.von-hugo-multimob-future-work]
              Hugo, D., Asaeda, H., Sarikaya, B., and P. Seite,
              "Evaluation of further issues on Multicast Mobility:
              Potential future work for WG MultiMob",
              draft-von-hugo-multimob-future-work-02 (work in progress),
              June 2010.

   [Papagiannaki]
              Papagiannaki, K., Moon, S., Fraliegh, C., Thiran, P., and
              C. Diot, "Measurement and Analysis of Single-Hop Delay on
              an IP Backbone Network", IEEE Journal on Selected Areas in
              Communications, vol.21, no.6 , August 2003.




Contreras, et al.        Expires January 9, 2014               [Page 31]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   [RFC3810]  Vida, R. and L. Costa, "Multicast Listener Discovery
              Version 2 (MLDv2) for IPv6", RFC 3810, June 2004.

   [RFC5949]  Yokota, H., Chowdhury, K., Koodli, R., Patil, B., and F.
              Xia, "Fast Handovers for Proxy Mobile IPv6", RFC 5949,
              September 2010.

   [RFC6224]  Schmidt, T., Waehlisch, M., and S. Krishnan, "Base
              Deployment for Multicast Listener Support in Proxy Mobile
              IPv6 (PMIPv6) Domains", RFC 6224, April 2011.

   [RFC6636]  Asaeda, H., Liu, H., and Q. Wu, "Tuning the Behavior of
              the Internet Group Management Protocol (IGMP) and
              Multicast Listener Discovery (MLD) for Routers in Mobile
              and Wireless Networks", RFC 6636, May 2012.

   [Verizon]  "LTE: The Future of Mobile Broadband Technology", Verizon
              White Paper (http://opennetwork.verizonwireless.com/pdfs/
              VZW_LTE_White_Paper_12-10.pdf) , 2010.

   [Y.1541]   "Network performance objectives for IP-based services",
              ITU-T Recommendation Y.1541 , December 2011.


Appendix A.  Performance comparison with base solution

   This appendix briefly analyzes and compares the performance
   improvement provided by the fast handover extensions specified in
   this document with the base multicast solution defined in [RFC6224].
   The main aim is to determine the potential delay reduction in the
   acquisition of the multicast subscription information by the nMAG
   during the MN handover.  To do that, the analysis focuses on the
   delay additional to the unicast handover due to the multicast
   operation in both cases.

   Different delay components have to be taken into account for this
   comparison.  Since the interaction between the actors during the
   handover process (MN, pMAG, nMAG, LMA) is different for each of the
   solutions, then different sources of delay can be expected for each
   of them.

A.1.  Delay characterization of the base solution

   The base solution relies on the standard MLD procedures to obtain the
   multicast subscription information directly from the MN.  Once the
   nMAG completes the configuration of point-to-point link to the
   attaching MN (the configuration of this link as downstream interface
   of an MLD proxy instance can run in parallel), it immediately sends



Contreras, et al.        Expires January 9, 2014               [Page 32]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   an MLD General Query towards the MN for getting knowledge of any
   active multicast subscription by the MN.  When the MN receives the
   MLD Query, the MN provides information about the active memberships
   it maintains in the form of an MLD Report message.  After successful
   transmission of this information via the wireless point of attachment
   to nMAG the corresponding MLD proxy instance at the nMAG will set up
   the multicast status of the downstream interface.  According to this
   process, the delay is originated on the MAG-MN communication.

   The delay components to be considered for the base solution are the
   following:

   o  D_bh, which is the unidirectional (one way) delay encountered in
      the transmission path between the nMAG and the wireless point of
      attachment

   o  D_radio, which is the unidirectional delay due to the transfer of
      MLD control messages over the radio channel (user plane) between
      the wireless point of attachment and the MN, for the MLD Query and
      Report messages.

   o  D_mld, which is the delay incurred by the MN to answer the MLD
      Query.

   The total observed delay can be then formulated as:

   D_base = 2 x (D_bh + D_radio) + D_mld

A.2.  Delay characterization of the extensions defined in this document

   As described in this document, it is possible to distinguish two
   scenarios depending on the order in which the LMA receives the
   notifications of the MN registration and de-registration in the nMAG
   and the pMAG respectively.

   In the proactive case, the MN is firstly de-registered by the pMAG,
   and later on it is registered by the nMAG.  As specified in this
   document, the LMA will store the multicast subscription information,
   which will be provided to the nMAG during the MN registration
   process.  Since the registration process necessarily happens before
   the MLD Query and Report process described in the base solution, the
   proactive case is inherently faster than the base solution.  In fact,
   since the multicast subscription information is acquired properly
   during the registration process, the delay incurred is null.

   In the reactive case, the LMA receives the MN registration from the
   nMAG without having previously received the MN de-registration from
   the pMAG.  In case the MN maintains an active subscription, the LMA



Contreras, et al.        Expires January 9, 2014               [Page 33]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   will query the pMAG to retrieve the multicast subscription
   information, which is forwarded to the nMAG.  According to this
   process, the delay is originated on the MAG-LMA communication.

   The delay components to be considered for the base solution are the
   following:

   o  D_net, which is the unidirectional delay found in the network path
      between the LMA and the MAG.

   The total observed delay can be then formulated as:

   D_sial = 2 x D_net

A.3.  Performance comparison

   The performance of the base solution is highly dependent on the radio
   technology used by the MN to attach to the PMIPv6-Domain.  Different
   radio technologies have distinct properties in terms of radio
   framing, radio access contention or collision avoidance, channel
   reliability, etc.

   New radio access technologies, such as the one specified in new Long
   Term Evolution (LTE) standards intend to reduce the latency in order
   to provide high speed communications.  Even though, typical one-way
   latencies in the LTE radio access will stay around 15 ms [Verizon].

   The backhaul delay characterization becomes problematic.  In a real
   network there are several solutions for the backhaul connection in
   terms of network topology (ring, star, point-to-point, etc) and
   technology (optical fiber, microwave transmission, xDSL-based
   accesses, etc), all of them having distinct properties in terms of
   performance, reliability and delay.  These solutions commonly coexist
   in a real mobile network, in such a way that an MN changing the point
   of attachment can pass smoothly from one solution to another.  A
   value of D_bh=5 ms can be established as typical value for the
   backhaul latency in modern networks.

   Finally, the MLD induced delay is intrinsic to the MLD protocol
   specification.  A host receiving an MLD Query message will wait a
   random time in the range (0, Maximum Response Delay) to send the MLD
   Report message.  The default value of the Maximum Response Delay
   (configurable through the Query Response Interval in MLD) is 10 s in
   [RFC2710], or 5 s in the best case described in [RFC6636].  Then, in
   average, it can be expected a potential delay of 5 or 2,5 s,
   respectively.

   As we have seen, D_base is, on average, greater than 2,5 sec with the



Contreras, et al.        Expires January 9, 2014               [Page 34]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   best case of the values of Query Response Interval in MLD that are
   recommended in [RFC6636].  That means that the handover delay of the
   base solution is on the order of seconds while in the solution
   presented in this specification it is on the order of milliseconds
   (as it is shown below).  To improve the performance of the base
   solution we could further reduce the value of Query Response Interval
   but the implications of doing so would need to be carefully analyzed.
   Even if we assume that Query Response Interval is 0 sec, D_base would
   be of around 2 x (5 ms + 15 ms) = 40 ms for last generation systems.
   Note that this calculation does not take into account the necessary
   time to re-establish the data plane after the handover to make
   possible the MLD Query reception.  The expected delay will get much
   worse for older generation systems (e.g., 3G-based radio systems can
   suffer radio delays in the order of hundreds of ms).

   For the SIAL case, the delay in the MAG-LMA communication will be
   derived from the network diameter (i.e., the number of hops found
   between the MAG and the LMA in the PMIPv6-Domain).  This is largely
   influenced by the internal network planning.  An administrative
   domain can typically have in the order of 5 hops from access to the
   interconnection gateway providing connectivity to other networks.
   Even if the LMA plays a central role topologically in the PMIPv6
   domain, such number of hops seems reasonable in a common nation-wide
   network.  Each hop in the path between MAG and LMA will add a certain
   delay, which can be estimated to be around 1 ms in the best case
   [Papagiannaki] and 3 ms in the worst case [Y.1541].  With this in
   mind, a total delay D_sial of around 2 x 5 x 3 ms = 30 ms can be
   expected in the worst case.

   Then, as conclusion, in a typical deployment, it can be stated that
   SIAL proposal, even for the worst-case consideration, will perform
   better than the best case situation for the base solution, which
   consists of the last generation radio technology, LTE.  For any other
   radio technology the base solution will show even larger deviation
   from the delay achievable with the SIAL proposal.


Appendix B.  Change Log

   The following changes has been made from -00 version.

   1.  Multicast Address Record format defined in [RFC3810] has been
       adopted for transfering multicast subscrition information in the
       Active Multicast Subscription mobility option.

   The following changes has been made from -01 version.





Contreras, et al.        Expires January 9, 2014               [Page 35]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


   1.  A new appendix has been created to include a performance
       comparison between this proposal and the base solution.

   2.  Comments from Akbar Rahman review has been addressed.

   The following changes has been made from -02 version.

   1.  Minor editorial corrections.

   The following changes has been made from
   draft-ietf-multimob-fast-handover-03 version.

   1.  The name of the draft file has been changed to
       draft-ietf-multimob-handover-optimization as requested by the
       chairs.

   The following changes has been made from
   draft-ietf-multimob-handover-optimization-00 version.

   1.  New Section 1.1 has been introduced to list a number of basic
       requirements to be covered for an optimization solution to the
       handover process in [RFC6224].

   2.  New Section 6 has been introduced to define the support of IPv4-
       based MNs in this specification.

   3.  Section 4.1 has been reworked for facilitating the alignment with
       the IPv4 format defined in new Section 6.

   4.  Minor editorial corrections.

   The following changes has been made from
   draft-ietf-multimob-handover-optimization-01 version.

   1.  Clarification statements added in several sections according to
       the comments from B. Sarikaya and S. Venaas.

   2.  Minor editorial corrections.

   The following changes has been made from
   draft-ietf-multimob-handover-optimization-02 version.

   1.  Removal of flag A mechanism description and associated stuff.

   2.  Minor editorial corrections.






Contreras, et al.        Expires January 9, 2014               [Page 36]

Internet-Draft   PMIPv6 multicast handover optimization        July 2013


Authors' Addresses

   Luis M. Contreras
   Telefonica I+D
   Ronda de la Comunicacion, s/n
   Sur-3 building, 3rd floor
   Madrid  28050
   Spain

   Email: lmcm@tid.es


   Carlos J. Bernardos
   Universidad Carlos III de Madrid
   Av. Universidad, 30
   Leganes, Madrid  28911
   Spain

   Phone: +34 91624 6236
   Email: cjbc@it.uc3m.es
   URI:   http://www.it.uc3m.es/cjbc/


   Ignacio Soto
   Universidad Carlos III de Madrid
   Av. Universidad, 30
   Leganes, Madrid  28911
   Spain

   Email: isoto@it.uc3m.es





















Contreras, et al.        Expires January 9, 2014               [Page 37]


Html markup produced by rfcmarkup 1.109, available from https://tools.ietf.org/tools/rfcmarkup/