[Docs] [txt|pdf|xml|html] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: (draft-ishiguro-ospf-ospfv3-traffic) 00 01 02 03 04 05 06 07 08 09 10 11 12 13 RFC 5329

Network Working Group                                        K. Ishiguro
Internet-Draft                                                 V. Manral
Intended status: Standards Track                        IP Infusion, Inc
Expires: December 14, 2008                                      A. Davey
                                                 Data Connection Limited
                                                      A. Lindem (Editor)
                                                        Redback Networks
                                                           June 12, 2008


            Traffic Engineering Extensions to OSPF version 3
                 draft-ietf-ospf-ospfv3-traffic-13.txt

Status of this Memo

   By submitting this Internet-Draft, each author represents that any
   applicable patent or other IPR claims of which he or she is aware
   have been or will be disclosed, and any of which he or she becomes
   aware will be disclosed, in accordance with Section 6 of BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

   This Internet-Draft will expire on December 14, 2008.

Copyright Notice

   Copyright (C) The IETF Trust (2008).










Ishiguro, et al.        Expires December 14, 2008               [Page 1]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


Abstract

   This document describes extensions to OSPFv3 to support intra-area
   Traffic Engineering (TE).  This document extends OSPFv2 TE to handle
   IPv6 networks.  A new TLV and several new sub-TLVs are defined to
   support IPv6 networks.


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
     1.1.  Requirements notation  . . . . . . . . . . . . . . . . . .  3
   2.  Intra-Area-TE-LSA  . . . . . . . . . . . . . . . . . . . . . .  4
     2.1.  Intra-Area-TE-LSA Payload  . . . . . . . . . . . . . . . .  5
   3.  Router IPv6 Address TLV  . . . . . . . . . . . . . . . . . . .  6
   4.  Link TLV . . . . . . . . . . . . . . . . . . . . . . . . . . .  7
     4.1.  Link ID Sub-TLV  . . . . . . . . . . . . . . . . . . . . .  7
     4.2.  Neighbor ID Sub-TLV  . . . . . . . . . . . . . . . . . . .  7
     4.3.  Local Interface IPv6 Address Sub-TLV . . . . . . . . . . .  8
     4.4.  Remote Interface IPv6 Address Sub-TLV  . . . . . . . . . .  9
   5.  Security Considerations  . . . . . . . . . . . . . . . . . . . 11
   6.  Management Considerations  . . . . . . . . . . . . . . . . . . 12
   7.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 13
   8.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 14
     8.1.  Normative References . . . . . . . . . . . . . . . . . . . 14
     8.2.  Informative References . . . . . . . . . . . . . . . . . . 14
   Appendix A.  Acknowledgments . . . . . . . . . . . . . . . . . . . 15
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 16
   Intellectual Property and Copyright Statements . . . . . . . . . . 17






















Ishiguro, et al.        Expires December 14, 2008               [Page 2]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


1.  Introduction

   OSPFv3 has a very flexible mechanism for adding new LS types.
   Unknown LS types are flooded properly based on the flooding scope
   bits in the LS type [OSPFV3].  This document defines the
   Intra-Area-TE LSA to OSPFv3.

   For Traffic Engineering, this document uses "Traffic Engineering
   Extensions to OSPF" [TE] as a base for TLV definitions.  New TLVs and
   sub-TLVs are added to [TE] to extend TE capabilities to IPv6
   networks.  Some existing TLVs and sub-TLVs require clarification for
   OSPFv3 applicability.

   GMPLS [GMPLS] and the Diff-Serv MPLS Extensions [TE-DIFF] are based
   on [TE].  These functions can also be extended to OSPFv3 by utilizing
   the TLVs and sub-TLVs described in this document.

1.1.  Requirements notation

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC2119
   [RFC-KEYWORDS].




























Ishiguro, et al.        Expires December 14, 2008               [Page 3]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


2.  Intra-Area-TE-LSA

   A new LS type is defined for the Intra-Area-TE LSA.  This is
   different from OSPFv2 Traffic Engineering [TE] where opaque LSAs are
   used to advertise TE information [OPAQUE].  The LSA function code is
   10, the U bit is set, and the scope is set to 01 for area-scoping.
   When the U bit is set to 1, an OSPFv3 router must flood the LSA at
   its defined flooding scope even if it does not recognize the LS type
   [OSPFV3].



       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |            LS age             |1|0|1|          10             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    Link State ID                              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    Advertising Router                         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    LS sequence number                         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |        LS checksum            |            Length             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                                                               |
      +-                            TLVs                             -+
      |                             ...                               |


                         OSPFv3 Intra-Area-TE-LSA

   The Link State ID of an Intra-Area-TE LSA is an arbitrary value used
   to maintain multiple Traffic Engineering LSAs.  The LSA ID has no
   topological significance.

   The format of the TLVs within the body of an Intra-Area-TE LSA is the
   same as the format used by the Traffic Engineering Extensions to OSPF
   [TE].  The LSA payload consists of one or more nested Type/Length/
   Value (TLV) triplets.  The format of each TLV is:


      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |              Type             |             Length            |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                            Value...                           |



Ishiguro, et al.        Expires December 14, 2008               [Page 4]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


                                TLV Format

   The Length field defines the length of the value portion in octets
   (thus a TLV with no value portion would have a length of zero).  The
   TLV is padded to four-octet alignment; padding is not included in the
   length field (so a three octet value would have a length of three,
   but the total size of the TLV would be eight octets).  Nested TLVs
   are also 32-bit aligned.  For example, a one-byte value would have
   the length field set to 1, and three octets of padding would be added
   to the end of the value portion of the TLV.  Unrecognized types are
   ignored.

2.1.  Intra-Area-TE-LSA Payload

   An Intra-Area-TE-LSA contains one top-level TLV.  There are two
   applicable top-level TLVs:

      2 - Link TLV

      3 - Router IPv6 Address TLV




























Ishiguro, et al.        Expires December 14, 2008               [Page 5]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


3.  Router IPv6 Address TLV

   The Router IPv6 Address TLV advertises a reachable IPv6 address.
   This is a stable IPv6 address that is always reachable if there is
   connectivity to the OSPFv3 router.

   The Router IPv6 Address TLV has type 3, length 16, and a value
   containing a 16 octet local IPv6 address.  A Link-local address MUST
   NOT be specified for this TLV.  It MUST appear in exactly one Traffic
   Engineering LSA originated by an OSPFv3 router supporting the TE
   extensions.  The Router IPv6 Address TLV is a top-level TLV as
   defined in Traffic Engineering Extensions to OSPF [TE] and only one
   top-level TLV may be contained in an LSA.


       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |              3                |            16                 |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                                                               |
      +-+-+-+-                                                 -+-+-+-+
      |                                                               |
      +-+-+-+-             Router IPv6 Address                 -+-+-+-+
      |                                                               |
      +-+-+-+-                                                 -+-+-+-+
      |                                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


      Type     A 16-bit field set to 3.
      Length   A 16-bit field that indicates the length of the value
               portion in octets. For this TLV it is always 16.
      Value    A stable and routable IPv6 address.


                          Router IPv6 Address TLV














Ishiguro, et al.        Expires December 14, 2008               [Page 6]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


4.  Link TLV

   The Link TLV describes a single link and consists of a set of sub-
   TLVs [TE].  All of the sub-TLVs in [TE] other than the Link ID sub-
   TLV are applicable to OSPFv3.  The Link ID sub-TLV can't be used in
   OSPFv3 since it is defined to use the OSPFv2 identification for the
   Designated Router (DR) on multi-access networks.  In OSPFv2,
   neighbors on point-to-point networks and virtual links are identified
   by their Router IDs while neighbors on broadcast, Non-Broadcast
   Multi-Access (NBMA), and Point-to-Multipoint links are identified by
   their IPv4 interface addresses (Refer to section 8.2 in [OSPFV2]).
   The IPv4 interface address is not known to OSPFv3.  In contrast to
   OSPFv2, OSPFv3 always identifies neighboring routers by their Router
   IDs (Refer to section 2.11 in [OSPFV3]).

   Three new sub-TLVs for the Link TLV are defined:

      18 - Neighbor ID (8 octets)

      19 - Local Interface IPv6 Address (16N octets, where N is the
      number of IPv6 addresses)

      20 - Remote Interface IPv6 Address (16N octets, where N is the
      number of IPv6 addresses)

   The Neighbor ID Sub-TLV is mandatory for OSPF3 Traffic Engineering
   support.  It MUST appear exactly once in a Link TLV.  All other sub-
   TLVs defined in this document SHOULD NOT occur more than once in a
   LINK TLV.  If a sub-TLV is specified more than once, instances
   subsequent to the first are ignored.

4.1.  Link ID Sub-TLV

   The Link ID sub-TLV is used in OSPFv2 to identify the other end of
   the link.  In OSPFv3, the Neighbor ID sub-TLV MUST be used for link
   identification.  In OSPFv3, The Link ID sub-TLV SHOULD NOT be sent
   and MUST be ignored upon receipt.

4.2.  Neighbor ID Sub-TLV

   In OSPFv2, the Link ID is used to identify the other end of a link.
   In OSPFv3, the combination of Neighbor Interface ID and Neighbor
   Router ID is used for neighbor link identification.  Both are
   advertised in the Neighbor ID Sub-TLV.

   Neighbor Interface ID and Neighbor Router ID values are the same as
   described in RFC 2740 [OSPFV3] A.4.3 Router-LSAs.




Ishiguro, et al.        Expires December 14, 2008               [Page 7]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |              18               |             8                 |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |             Neighbor Interface ID                             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |             Neighbor Router ID                                |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


      Type     A 16-bit field set to 18.
      Length   A 16-bit field that indicates the length of the value
               portion in octets. For this sub-TLV it is always 8.
      Value    The neighbor's interface ID and router ID.


                            Neighbor ID Sub-TLV

4.3.  Local Interface IPv6 Address Sub-TLV

   The Local Interface IPv6 Address sub-TLV specifies the IPv6
   address(es) of the interface corresponding to this link.  If there
   are multiple local addresses assigned to the link then they MAY all
   be listed in this sub-TLV.  Link-local addresses MUST NOT be included
   in this sub-TLV.

























Ishiguro, et al.        Expires December 14, 2008               [Page 8]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |              19               |              Length           |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                                                               |
      +-+-+-+-                                                 -+-+-+-+
      |                                                               |
      +-+-+-+-             Local Interface  IPv6 Address       -+-+-+-+
      |                                                               |
      +-+-+-+-                                                 -+-+-+-+
      |                                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                         o                                     |
      |                         o                                     |
      |                         o                                     |
      |                                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                                                               |
      +-+-+-+-                                                 -+-+-+-+
      |                                                               |
      +-+-+-+-          Local Interface IPv6 Address           -+-+-+-+
      |                                                               |
      +-+-+-+-                                                 -+-+-+-+
      |                                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      Type     A 16-bit field set to 19.
      Length   A 16-bit field that indicates the length of the value
               portion in octets. For this sub-TLV, it MUST always be a
               multiple of 16 octets dependent on the number of IPv6
               global addresses advertised.
      Value    A list of one or more local IPv6 interface addresses
               each consuming 16 octets.


                   Local Interface IPv6 Address Sub-TLV

4.4.  Remote Interface IPv6 Address Sub-TLV

   The Remote Interface IPv6 Address sub-TLV advertises the IPv6
   address(es) associated with the neighbor's interface.  This Sub-TLV
   and the Local Interface IPv6 address Sub-TLV are used to discern
   amongst parallel links between OSPFv3 routers.  If the Link Type is
   multi-access, the Remote Interface IPv6 Address MAY be set to ::.
   Alternately, an implementation MAY choose not to send this sub-TLV.
   Link-local addresses MUST NOT be advertised in this sub-TLV.
   Neighbor addresses advertised in Link-LSAs with a prefix length of



Ishiguro, et al.        Expires December 14, 2008               [Page 9]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


   128 and the LA bit set MAY be advertised.


       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |              20               |              Length           |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                                                               |
      +-+-+-+-                                                 -+-+-+-+
      |                                                               |
      +-+-+-+-             Remote Interface IPv6 Address       -+-+-+-+
      |                                                               |
      +-+-+-+-                                                 -+-+-+-+
      |                                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                         o                                     |
      |                         o                                     |
      |                         o                                     |
      |                                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                                                               |
      +-+-+-+-                                                 -+-+-+-+
      |                                                               |
      +-+-+-+-             Remote Interface IPv6 Address       -+-+-+-+
      |                                                               |
      +-+-+-+-                                                 -+-+-+-+
      |                                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      Type     A 16-bit field set to 20.
      Length   A 16-bit field that indicates the length of the value
               portion in octets. For this sub-TLV, it MUST be a
               multiple of 16 octets dependent on the number of IPv6
               global addresses advertised.
      Value    A variable length remote interface IPv6 address list.


                   Remote Interface IPv6 Address Sub-TLV












Ishiguro, et al.        Expires December 14, 2008              [Page 10]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


5.  Security Considerations

   The function described in this document does not create any new
   security issues for the OSPFv3 protocol.  Security considerations for
   the base OSPFv3 protocol [OSPFV3] and OSPFv2 Traffic Engineering [TE]
   are applicable to OSPFv3 Traffic Engineering.













































Ishiguro, et al.        Expires December 14, 2008              [Page 11]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


6.  Management Considerations

   The typical management interface for routers running the new
   extensions to OSPF for intra-area Traffic Engineering is SNMP-based.
   The extra management objects for configuration operations and
   statistics are defined in [OSPFV3-MIB] and an implementation of the
   extensions defined in this document SHOULD provide for the
   appropriate hooks or instrumentation that allow for the MIB objects
   to be implemented.

   The following MIB variables have been added to the OSPFv3 MIB in
   support of TE:


   ospfv3AreaTEEnabled
      This TruthValue MIB variable in the ospf3AreaEntry table entry
      indicates whether or not OSPFv3 TE advertisement for OSPFv3
      interfaces is enabled for the corresponding area.  The default
      value is FALSE.

   ospfv3IfTEDisabled
      This TruthValue MIB variable in the ospf3IfEntry table entry
      indicates whether or not OSPFv3 TE advertisement for OSPFv3 for
      the corresponding interface is disabled.  This MIB variable is
      only applicable if ospfv3AreaTEEnabled is TRUE for the interface's
      area.  The default value is FALSE.

























Ishiguro, et al.        Expires December 14, 2008              [Page 12]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


7.  IANA Considerations

   The following IANA assignments are to be made from existing
   registries:

   1.  The OSPFv3 LSA type function code 10 needs to be assigned to the
       OSPFv3 Intra-Area-TE-LSA.

   2.  The Router IPv6 Address TLV type 3 needs to be assigned from the
       existing registry for OSPF TE TLVs.

   3.  The Neighbor ID Sub-TLV (18), Local Interface IPv6 Address Sub-
       TLV (19), and Remote Interface IPv6 Address Sub-TLV (20), need to
       be assigned from the existing registry for OSPF TE Sub-TLVs.





































Ishiguro, et al.        Expires December 14, 2008              [Page 13]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


8.  References

8.1.  Normative References

   [OSPFV2]   Moy, J., "OSPF Version 2", RFC 2328, April 1998.

   [OSPFV3]   Coltun, R., Ferguson, D., Moy, J., and A. Lindem, "OSPF
              for IPv6", draft-ietf-ospf-ospfv3-update-23.txt (work in
              progress).

   [RFC-KEYWORDS]
              Bradner, S., "Key words for use in RFC's to Indicate
              Requirement Levels", RFC 2119, March 1997.

   [TE]       Katz, D., Yeung, D., and K. Kompella, "Traffic Engineering
              Extensions to OSPF", RFC 3630, September 2003.

8.2.  Informative References

   [GMPLS]    Kompella, K. and Y. Rekhter, "OSPF Extensions in Support
              of Generalized Multi-Protocol Switching (GMPLS)",
              RFC 4203, October 2005.

   [OPAQUE]   Coltun, R., "The OSPF Opaque LSA Option", RFC 2370,
              July 1998.

   [OSPFV3-MIB]
              Joyal, D. and V. Manral, "Management Information Base for
              OSPFv3", draft-ietf-ospf-ospfv3-mib-12.txt (work in
              progress).

   [TE-DIFF]  Le Faucheur, F., Wu, L., Davie, B., Davari, S., Vaananen,
              P., Krishnan, R., Cheval, P., and J. Heinanen, "Multi-
              Protocol Label Switching (MPLS) Support of Differentiated
              Services", RFC 3270.
















Ishiguro, et al.        Expires December 14, 2008              [Page 14]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


Appendix A.  Acknowledgments

   Thanks to Kireeti Kompella, Alex Zinin, Adrian Farrell, and Mach Chen
   for their comments.

   Thanks to Vijay K. Gurbani for providing the General Area Review Team
   (Gen-ART) review.

   Thanks to Rob Austein for providing the Security Directorate (secdir)
   review.

   Thanks to Dan Romascanu for providing the text for the "Management
   Considerations" Section 6 section in the context of the IESG review.

   Thanks to Dave Ward, Tim Polk, Jari Arko, and Pasi Eronen for
   comments and relevant discussion in the context of the IESG review.

   The RFC text was produced using Marshall Rose's xml2rfc tool.

































Ishiguro, et al.        Expires December 14, 2008              [Page 15]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


Authors' Addresses

   Kunihiro Ishiguro
   IP Infusion, Inc
   125 South Market Street, Suite 900
   San Jose, CA  95113
   USA

   Email: kunihiro@ipinfusion.com


   Vishwas Manral
   IP Infusion, Inc
   #41, Ground Floor, 5th Cross Road
   8th Main Road
   Vasanth Nagar, Bangalore  560052
   India

   Email: vishwas@ipinfusion.com


   Alan Davey
   Data Connection Limited
   100 Church Street
   Enfield
   EN2 6BQ
   UK

   Email: Alan.Davey@dataconnection.com


   Acee Lindem
   Redback Networks
   102 Carric Bend Court
   Cary, NC  27519
   USA

   Email: acee@redback.com













Ishiguro, et al.        Expires December 14, 2008              [Page 16]

Internet-Draft         OSPFv3-Traffic Engineering              June 2008


Full Copyright Statement

   Copyright (C) The IETF Trust (2008).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
   THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
   OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.


Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.


Acknowledgment

   Funding for the RFC Editor function is provided by the IETF
   Administrative Support Activity (IASA).





Ishiguro, et al.        Expires December 14, 2008              [Page 17]


Html markup produced by rfcmarkup 1.107, available from http://tools.ietf.org/tools/rfcmarkup/