[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 04 05 06 07 08 RFC 5088

Network Working Group                              J.L. Le Roux (Editor)
Internet Draft                                            France Telecom
Intended Status: Standard Track
Expires: April 2008                                J.P. Vasseur (Editor)
                                                       Cisco System Inc.

                                                          Yuichi Ikejiri
                                                      NTT Communications

                                                           Raymond Zhang
                                                              BT Infonet

                                                            October 2007




  OSPF Protocol Extensions for Path Computation Element (PCE) Discovery

               draft-ietf-pce-disco-proto-ospf-08.txt


Status of this Memo

   By submitting this Internet-Draft, each author represents that any
   applicable patent or other IPR claims of which he or she is aware
   have been or will be disclosed, and any of which he or she becomes
   aware will be disclosed, in accordance with Section 6 of BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.


Copyright Notice

   Copyright (C) The IETF Trust (2007).  All rights reserved.



Le Roux, Vasseur et al.  OSPF extensions for PCE discovery      [Page 1]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007


Abstract

   There are various circumstances where it is highly desirable for a
   Path Computation Client (PCC) to be able to dynamically and
   automatically discover a set of Path Computation Elements (PCEs),
   along with information that can be used by the PCC for PCE selection.
   When the PCE is a Label Switching Router (LSR) participating in the
   Interior Gateway Protocol (IGP), or even a server participating
   passively in the IGP, a simple and efficient way to announce PCEs
   consists of using IGP flooding. For that purpose, this document
   defines extensions to the Open Shortest Path First (OSPF) routing
   protocol for the advertisement of PCE Discovery information within an
   OSPF area or within the entire OSPF routing domain.

Conventions used in this document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED",  "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

Table of Contents

   1.      Terminology.................................................3
   2.      Introduction................................................4
   3.      Overview....................................................5
   3.1.    PCE Discovery Information...................................5
   3.2.    Flooding Scope..............................................5
   4.      The OSPF PCED TLV...........................................6
   4.1.    PCE-ADDRESS Sub-TLV.........................................7
   4.2.    PATH-SCOPE Sub-TLV..........................................8
   4.3.    PCE-DOMAIN Sub-TLV.........................................10
   4.4.    NEIG-PCE-DOMAIN Sub-TLV....................................11
   4.5.    PCE-CAP-FLAGS Sub-TLV......................................11
   5.      Elements of Procedure......................................13
   6.      Backward Compatibility.....................................13
   7.      IANA Considerations........................................14
   7.1.    OSPF TLV...................................................14
   7.2.    PCE Capability Flags registry..............................14
   8.      Security Considerations....................................15
   9.      Manageability Considerations...............................15
   9.1.    Control of Policy and Functions............................15
   9.2.    Information and Data Model.................................15
   9.3.    Liveness Detection and Monitoring..........................15
   9.4.    Verify Correct Operations..................................16
   9.5.    Requirements on Other Protocols and Functional
             Components...............................................16
   9.6.    Impact on Network Operations...............................16
   10.     Acknowledgments............................................16
   11.     References.................................................16
   11.1.   Normative References.......................................16
   11.2.   Informative References.....................................17
   12.     Editor's Addresses.........................................17

Le Roux, Vasseur et al. OSPF extensions for PCE Discovery     [Page 2]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007


   13.     Contributors' Addresses....................................18
   14.     Intellectual Property Statement............................18

1. Terminology

      ABR: OSPF Area Border Router.

      AS: Autonomous System.

      IGP: Interior Gateway Protocol. Either of the two routing
      protocols Open Shortest Path First (OSPF) or Intermediate System
      to Intermediate System (ISIS).

      Intra-area TE LSP: A TE LSP whose path does not cross an IGP area
      boundary.

      Intra-AS TE LSP: A TE LSP whose path does not cross an AS
      boundary.

      Inter-area TE LSP: A TE LSP whose path transits two or more IGP
      areas. That is a TE LSP that crosses at least one IGP area
      boundary.

      Inter-AS TE LSP: A TE LSP whose path transits two or more
      ASes or sub-ASes (BGP confederations). That is a TE LSP that
      crosses at least one AS boundary.

      LSA: Link State Advertisement.

      LSR: Label Switching Router.

      PCC: Path Computation Client. Any client application requesting a
      path computation to be performed by a Path Computation Element.

      PCE: Path Computation Element. An entity (component, application,
      or network node) that is capable of computing a network path or
      route based on a network graph, and applying computational
      constraints.

      PCE-Domain: In a PCE context this refers to any collection of
      network elements within a common sphere of address management or
      path computational responsibility (referred to as a "domain" in
      [RFC4655]). Examples of PCE-Domains include IGP areas and ASes.
      This should be distinguished from an OSPF routing domain.

      PCEP: Path Computation Element Protocol.

      TE LSP: Traffic Engineered Label Switched Path.





Le Roux, Vasseur et al. OSPF extensions for PCE Discovery     [Page 3]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007


2. Introduction

   [RFC4655] describes the motivations and architecture for a Path
   Computation Element (PCE)-based
   path computation model for Multi-Protocol Label Switching (MPLS) and
   Generalized MPLS (GMPLS) Traffic Engineered Label Switched Paths (TE
   LSPs). The model allows for the separation of the PCE from a Path
   Computation Client (PCC) (also referred to as a non co-located PCE)
   and allows for cooperation between PCEs (where one PCE acts as a PCC
   to make requests of the other PCE). This relies on a communication
   protocol between PCC and PCE, and also between PCEs. The requirements
   for such a communication protocol can be found in [RFC4657], and the
   communication protocol is defined in [PCEP].

   The PCE architecture requires that a PCC be aware of the location of
   one or more PCEs in its domain, and also, potentially, of PCEs in
   other domains, e.g., in the case of inter-domain TE LSP computation.

   A network may contain a large number of PCEs, each with potentially
   distinct capabilities. In such a context it is highly desirable to
   have a mechanism for automatic and dynamic PCE discovery that allows
   PCCs to automatically discover a set of PCEs along with additional
   information about each PCE that may be used by a PCC to perform PCE
   selection. Additionally, it is valuable for a PCC to dynamically
   detect new PCEs, failed PCEs, or any modification to the PCE
   information. Detailed requirements for such a PCE discovery mechanism
   are provided in [RFC4674].

   Note that the PCE selection algorithm applied by a PCC is out of the
   scope of this document.

   When PCCs are LSRs participating in the IGP (OSPF or IS-IS), and PCEs
   are either LSRs or servers also participating in the IGP, an
   effective mechanism for PCE discovery within an IGP routing domain
   consists of utilizing IGP advertisements.

   This document defines extensions to OSPFv2 [RFC2328] and OSPFv3
   [RFC2740] to allow a PCE in an OSPF routing domain to advertise its
   location along with some information useful to a PCC for PCE
   selection so as to satisfy dynamic PCE discovery requirements set
   forth in [RFC4674].

   Generic capability advertisement mechanisms for OSPF are defined in
   [OSPF-CAP]. These allow a router to advertise its capabilities within
   an OSPF area or an entire OSPF routing domain. This document
   leverages this generic capability advertisement mechanism to fully
   satisfy the dynamic PCE discovery requirements.

   This document defines a new TLV (named the PCE Discovery (PCED) TLV)
   to be carried within the OSPF Router Information LSA ([OSPF-CAP]).



Le Roux, Vasseur et al. OSPF extensions for PCE Discovery     [Page 4]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007


   The PCE information advertised is detailed in Section 3. Protocol
   extensions and procedures are defined in Sections 4 and 5.

   The OSPF extensions defined in this document allow for PCE discovery
   within an OSPF routing domain. Solutions for PCE discovery across AS
   boundaries are beyond the scope of this document, and for further
   study.

3. Overview


3.1. PCE Discovery Information

   The PCE discovery information is composed of:

   - The PCE location: an IPv4 and/or IPv6 address that is used to reach
     the PCE. It is RECOMMENDED to use an address that is always
     reachable if there is any connectivity to the PCE;

   - The PCE path computation scope (i.e., intra-area, inter-area,
     inter-AS, or inter-layer);

   - The set of one or more PCE-Domain(s) into which the PCE has
     visibility and for which the PCE can compute paths;

   - The set of zero, one or more neighbor PCE-Domain(s) toward which
     the PCE can compute paths;

   - A set of communication capabilities (e.g., support for request
     prioritization) and path computation-specific capabilities
     (e.g., supported constraints).

   PCE discovery information is by nature fairly static and does not
   change with PCE activity. Changes in PCE discovery information may
   occur as a result of PCE configuration updates, PCE
   deployment/activation, PCE deactivation/suppression, or PCE failure.
   Hence, this information is not expected to change frequently.


3.2. Flooding Scope

   The flooding scope for PCE information advertised through OSPF can be
   limited to one or more OSPF areas the PCE belongs to, or can be
   extended across the entire OSPF routing domain.

   Note that some PCEs may belong to multiple areas, in which case the
   flooding scope may comprise these areas. This could be the case for
   an ABR, for instance, advertising its PCE information within the
   backbone area and/or a subset of its attached IGP area(s).




Le Roux, Vasseur et al. OSPF extensions for PCE Discovery     [Page 5]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007




4. The OSPF PCED TLV

   The OSPF PCE Discovery TLV (PCED TLV) contains non-ordered set of
   sub-TLVs.

   The format of the OSPF PCED TLV and its sub-TLVs is identical to the
   TLV format used by the Traffic Engineering Extensions to OSPF
   [RFC3630]. That is, the TLV is composed of 2 octets for the type, 2
   octets specifying the TLV length, and a value field. The Length field
   defines the length of the value portion in octets.

   The TLV is padded to four-octet alignment; padding is not included in
   the Length field (so a three octet value would have a length of
   three, but the total size of the TLV would be eight octets). Nested
   TLVs are also four-octet aligned. Unrecognized types are ignored.

   The OSPF PCED TLV has the following format:

                        1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |              Type             |             Length            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   //                            sub-TLVs                          //
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


         Type     To be defined by IANA (suggested value=5)
         Length   Variable
         Value    This comprises one or more sub-TLVs

   Five sub-TLVs are defined:
         Sub-TLV type  Length               Name
               1      variable     PCE-ADDRESS sub-TLV
               2         4         PATH-SCOPE sub-TLV
               3         4         PCE-DOMAIN sub-TLV
               4         4        NEIG-PCE-DOMAIN sub-TLV
               5      variable     PCE-CAP-FLAGS sub-TLV

   The PCE-ADDRESS and PATH-SCOPE sub-TLVs MUST always be present within
   the PCED TLV.

   The PCE-DOMAIN and NEIG-PCE-DOMAIN sub-TLVs are optional. They MAY be
   present in the PCED TLV to facilitate selection of inter-domain PCEs.

   The PCE-CAP-FLAGS sub-TLV is optional and MAY be present in the PCED
   TLV to facilitate the PCE selection process.


Le Roux, Vasseur et al. OSPF extensions for PCE Discovery     [Page 6]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007



   Malformed PCED TLVs or sub-TLVs not explicitly described in this
   document MUST cause the LSA to be treated as malformed according to
   the normal procedures of OSPF.

   Any unrecognized sub-TLV MUST be silently ignored.

   The PCED TLV is carried within an OSPF Router Information LSA
   defined in [OSPF-CAP].

   No additional sub-TLVs will be added to the PCED TLV in the future.
   If a future application requires the advertisement of additional PCE
   information in OSPF, this will not be carried in the Router
   Information LSA.

   The following sub-sections describe the sub-TLVs which may be carried
   within the PCED sub-TLV.

4.1. PCE-ADDRESS Sub-TLV

   The PCE-ADDRESS sub-TLV specifies an IP address that can be
   used to reach the PCE. It is RECOMMENDED to make use of an address
   that is always reachable, provided that the PCE is alive and
   reachable.

   The PCE-ADDRESS sub-TLV is mandatory; it MUST be present within the
   PCED TLV. It MAY appear twice, when the PCE has both an IPv4 and IPv6
   address. It MUST NOT appear more than once for the same address type.
   If it appears more than once, only the first occurrence is processed
   and any others MUST be ignored.

   The format of the PCE-ADDRESS sub-TLV is as follows:

                            1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |              Type = 1         |             Length            |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |     address-type              |          Reserved             |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                                                               |
       //                       PCE IP Address                        //
       |                                                               |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                            PCE-ADDRESS sub-TLV format

         Type     1
         Length   8 (IPv4) or 20 (IPv6)

         Address-type:

Le Roux, Vasseur et al. OSPF extensions for PCE Discovery     [Page 7]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007


                       1   IPv4
                       2   IPv6

         Reserved: SHOULD be set to zero on transmission and MUST be
         ignored on receipt.

         PCE IP Address: The IP address to be used to reach the PCE.


4.2. PATH-SCOPE Sub-TLV

   The PATH-SCOPE sub-TLV indicates the PCE path computation scope,
   which refers to the PCE's ability to compute or take part in the
   computation of paths for intra-area, inter-area, inter-AS, or inter-
   layer_TE LSPs.

   The PATH-SCOPE sub-TLV is mandatory; it MUST be present within the
   PCED TLV. There MUST be exactly one instance of the PATH-SCOPE sub-
   TLV within each PCED TLV. If it appears more than once, only the
   first occurrence is processed and any others MUST be ignored.

   The PATH-SCOPE sub-TLV contains a set of bit-flags indicating the
   supported path scopes, and four fields indicating PCE preferences.

   The PATH-SCOPE sub-TLV has the following format:

                        1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |              Type = 2         |             Length            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |0|1|2|3|4|5|   Reserved        |PrefL|PrefR|PrefS|PrefY| Res   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


         Type     2
         Length   4
         Value    This comprises a 2-octet flag field where each bit
                  represents a supported path scope, as well as four
                  preference fields used to specify PCE preferences.

         The following bits are defined:

         Bit      Path Scope

          0      L bit:  Can compute intra-area paths
          1      R bit:  Can act as PCE for inter-area TE LSP
                         computation
          2      Rd bit: Can act as a default PCE for inter-area TE LSP
                         computation
          3      S bit:  Can act as PCE for inter-AS TE LSP computation
          4      Sd bit: Can act as a default PCE for inter-AS TE LSP

Le Roux, Vasseur et al. OSPF extensions for PCE Discovery     [Page 8]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007


                         computation
          5      Y bit:  Can compute or take part into the computation
                         of paths across layers.

          PrefL field: PCE's preference for intra-area TE LSPs
          computation.

          PrefR field: PCE's preference for inter-area TE LSPs
          computation.

          PrefS field: PCE's preference for inter-AS TE LSPs
          computation.

          PrefY field: PCE's preference for inter-layer TE LSPs
          computation.

          Res: Reserved for future use.

   The L, R, S, and Y bits are set when the PCE can act as a PCE for
   intra-area, inter-area, inter-AS, or inter-layer TE LSPs computation
   respectively. These bits are non-exclusive.

   When set, the Rd bit indicates that the PCE can act as a default PCE
   for inter-area TE LSPs computation (that is, the PCE can compute a
   path toward any neighbor area). Similarly, when set, the Sd bit
   indicates that the PCE can act as a default PCE for inter-AS TE LSP
   computation (the PCE can compute a path toward any neighbor AS).

   When the Rd and Sd bit are set the PCED TLV MUST NOT contain a NEIG-
   PCE-DOMAIN sub-TLV (see Section 4.1.4).

   When the R bit is clear, the Rd bit SHOULD be clear on transmission
   and MUST be ignore on receipt. When the S bit is clear, the Sd bit
   SHOULD be clear on transmission and MUST be ignored on receipt.

   The PrefL, PrefR, PrefS, and PrefY fields are each three bits long
   and allow the PCE to specify a preference for each computation scope,
   where 7 reflects the highest preference. Such preferences can be used
   for weighted load balancing of path computation requests. An operator
   may decide to configure a preference for each computation scope at
   each PCE so as to balance the path computation load among them. The
   algorithms used by a PCC to load balance its path computation
   requests according to such PCE preferences is out of the scope of
   this document and is a matter for local or network-wide policy. The
   same or different preferences may be used for each scope. For
   instance, an operator that wants a PCE capable of both inter-area and
   inter-AS computation to be prefered for use for inter-AS computations
   may configure PrefS higher than PrefR.

   When the L, R, S, or Y bits are cleared, the PrefL, PrefR, PrefS, and
   PrefY fields SHOULD respectively be set to 0 on transmission and MUST
   be ignored on receipt.

Le Roux, Vasseur et al. OSPF extensions for PCE Discovery     [Page 9]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007



   Both reserved fields SHOULD be set to zero on transmission and MUST
   be ignored on receipt.

4.3. PCE-DOMAIN Sub-TLV

   The PCE-DOMAIN sub-TLV specifies a PCE-Domain (area or AS) where the
   PCE has topology visibility and through which the PCE can compute
   paths.

   The PCE-DOMAIN sub-TLV SHOULD be present when PCE-Domains for which
   the PCE can operate cannot be inferred by other IGP information, for
   instance when the PCE is inter-domain capable (i.e., when the R bit
   or S bit is set) and the flooding scope is the entire routing domain
   (see Section 5 for a discussion of how the flooding scope is set and
   interpreted).

   A PCED TLV may include multiple PCE-DOMAIN sub-TLVs when the PCE has
   visibility into multiple PCE-Domains.

   The PCE-DOMAIN sub-TLV has the following format:

                            1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |              Type=3           |             Length            |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |     Domain-type               |          Reserved             |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                       Domain ID                               |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                            PCE-DOMAIN sub-TLV format

         Type     3
         Length   8

         Two domain-type values are defined:
                       1   OSPF Area ID
                       2   AS Number

         Domain ID: With the domain-type set to 1, this indicates the 32
         bit Area ID of an area where the PCE has visibility and can
         compute paths. With domain-type set to 2, this indicates an AS
         number of an AS where the PCE has visibility and can compute
         paths. When the AS number is coded in two octets, the AS Number
         field MUST have its first two octets set to 0.
.




Le Roux, Vasseur et al. OSPF extensions for PCE Discovery    [Page 10]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007


4.4. NEIG-PCE-DOMAIN Sub-TLV

   The NEIG-PCE-DOMAIN sub-TLV specifies a neighbor PCE-domain (area or
   AS) toward which a PCE can compute paths. It means that the PCE can
   take part in the computation of inter-domain TE LSPs with paths that
   transit this neighbor PCE-domain.

   A PCED sub-TLV may include several NEIG-PCE-DOMAIN sub-TLVs when the
   PCE can compute paths towards several neighbour PCE-domains.

   The NEIG-PCE-DOMAIN sub-TLV has the same format as the PCE-DOMAIN
   sub-TLV:

                            1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |              Type = 4         |             Length            |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |     Domain-type               |          Reserved             |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                           Domain ID                           |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                            NEIG-PCE-DOMAIN sub-TLV format

         Type     4
         Length   8

         Two domain-type values are defined:
                       1   OSPF Area ID
                       2   AS Number

         Domain ID: With the domain-type set to 1, this indicates the 32
         bit Area ID of a neighbour area toward which the PCE can
         compute paths. With domain-type set to 2, this indicates the AS
         number of a neighbor AS toward which the PCE can compute paths.
         When the AS number is coded in two octets, the AS Number field
         MUST have its first two octets set to 0.

   The NEIG-PCE-DOMAIN sub-TLV MUST be present at least once with
   domain-type set to 1 if the R bit is set and the Rd bit is cleared,
   and MUST be present at least once with domain-type set to 2 if the S
   bit is set and the Sd bit is cleared.

4.5. PCE-CAP-FLAGS Sub-TLV

   The PCE-CAP-FLAGS sub-TLV is an optional sub-TLV used to indicate PCE
   capabilities. It MAY be present within the PCED TLV. It MUST NOT be
   present more than once. If it appears more than once, only the first
   occurrence is processed and any others MUST be ignored.


Le Roux, Vasseur et al. OSPF extensions for PCE Discovery    [Page 11]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007


   The value field of the PCE-CAP-FLAGS sub-TLV is made up of an array
   of units of 32 bit-flags numbered from the most significant bit as
   bit zero, where each bit represents one PCE capability.

   The format of the PCE-CAP-FLAGS sub-TLV is as follows:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |              Type = 5         |             Length            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                                                               |
     //                 PCE Capability Flags                          //
      |                                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


         Type     5
         Length   Multiple of 4 octets
         Value    This contains an array of units of 32 bit flags
                  numbered from the most significant as bit zero, where
                  each bit represents one PCE capability.

   IANA is requested to manage the space of the PCE Capability Flags

   The following bits are to be assigned by IANA:


     Bit       Capabilities

      0        Path computation with GMPLS link constraints
      1        Bidirectional path computation
      2        Diverse path computation
      3        Load-balanced path computation
      4        Synchronized path computation
      5        Support for multiple objective functions
      6        Support for additive path constraints
               (max hop count, etc.)
      7        Support for request prioritization
      8        Support for multiple requests per message

     9-31    Reserved for future assignments by IANA.

   These capabilities are defined in [RFC4657].

   Reserved bits SHOULD be set to zero on transmission and MUST be
   ignored on receipt.





Le Roux, Vasseur et al. OSPF extensions for PCE Discovery    [Page 12]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007


5. Elements of Procedure

   The PCED TLV is advertised within OSPFv2 Router Information LSAs
   (Opaque type of 4 and Opaque ID of 0) or OSPFv3 Router Information
   LSAs (function code of 12) which are defined in [OSPF-CAP].  As such,
   elements of procedure are inherited from those defined in [OSPF-CAP].

   In OSPFv2 the flooding scope is controlled by the opaque LSA type (as
   defined in [RFC2370]) and in OSPFv3 by the S1/S2 bits (as defined in
   [RFC2740]). If the flooding scope is local to an area then the PCED
   TLV MUST be carried within an OSPFv2 type 10 router information LSA
   or an OSPFV3 Router Information LSA with the S1 bit set and the S2
   bit clear. If the flooding scope is the entire IGP domain then the
   PCED TLV MUST be carried within an OSPFv2 type 11 Router Information
   LSA or OSPFv3 Router Information LSA with the S1 bit clear and the S2
   bit set. When only the L bit of the PATH-SCOPE sub-TLV is set, the
   flooding scope MUST be area local.

   When the PCE function is deactivated, the OSPF speaker advertising
   this PCE MUST originate a new Router Information LSA that no longer
   includes the corresponding PCED TLV, provided there are other TLVs in
   the LSA. If there are no other TLVs in the LSA, it MUST either send
   an empty Router Information LSA or purge it by prematurely aging it.

   The PCE address (i.e., the address indicated within the PCE ADDRESS
   TLV) SHOULD be reachable via some prefixes advertised by OSPF. This
   allows the detection of a PCE failure to be sped up. When the PCE
   address is no longer reachable, the PCE node has failed, has been
   torn down, or there is no longer IP connectivity to the PCE.

   A change in information in the PCED TLV MUST NOT trigger any SPF
   computation at a receiving router.

   The way PCEs determine the information they advertise is out of the
   scope of this document. Some information may be configured on the PCE
   (e.g., address, preferences, scope) and other information may be
   automatically determined by the PCE (e.g., areas of visibility).


6. Backward Compatibility

   The PCED TLV defined in this document does not introduce any
   interoperability issues.

   A router not supporting the PCED TLV will just silently ignore the
   TLV as specified in [OSPF-CAP].







Le Roux, Vasseur et al. OSPF extensions for PCE Discovery    [Page 13]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007


7. IANA Considerations

7.1. OSPF TLV

   IANA has defined a registry for TLVs carried in the Router
   Information LSA defined in [OSPF-CAP]. IANA is requested to assign a
   new TLV code-point for the PCED TLV carried within the Router
   Information LSA.

   Value      TLV Name                      Reference
   -----     --------                       ----------
     5         PCED                       (this document)


7.2. PCE Capability Flags registry

   This document provides new capability bit flags, which are present
   in the PCE-CAP-FLAGS TLV referenced in section 4.1.5.

   The IANA is requested to create a new top-level OSPF registry, the
   "PCE Capability Flags" registry, and to manage the space of PCE
   capability bit flags numbering them in the usual IETF notation
   starting at zero and continuing at least through 31, with the most
   significant bit as bit zero.

   New bit numbers may be allocated only by an IETF Consensus action.

   Each bit should be tracked with the following qualities:

   - Bit number
   - Capability Description
   - Defining RFC

   Several bits are defined in this document. Here are the suggested
   values:

     Bit       Capability Description

      0        Path computation with GMPLS link constraints
      1        Bidirectional path computation
      2        Diverse path computation
      3        Load-balanced path computation
      4        Synchronized paths computation
      5        Support for multiple objective functions
      6        Support for additive path constraints
               (max hop count, etc.)
      7        Support for request prioritization
      8        Support for multiple requests per message





Le Roux, Vasseur et al. OSPF extensions for PCE Discovery    [Page 14]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007



8. Security Considerations

   This document defines OSPF extensions for PCE discovery within an
   administrative domain. Hence the security of the PCE discovery relies
   on the security of OSPF.

   Mechanisms defined to ensure authenticity and integrity of OSPF LSAs
   [RFC2154], and their TLVs, can be used to secure the PCE Discovery
   information as well.

   OSPF provides no encryption mechanism for protecting the privacy of
   LSAs, and in particular the privacy of the PCE discovery information.

9. Manageability Considerations

   Manageability considerations for PCE Discovery are addressed in
   Section 4.10 of [RFC4674].

9.1. Control of Policy and Functions

   Requirements for the configuration of PCE discovery parameters on
   PCCs and PCEs are discussed in Section 4.10.1 of [RFC4674].

   In particular, a PCE implementation SHOULD allow the following
   parameters to be configured on the PCE:
        - The PCE IPv4/IPv6 address(es) (see Section 4.1)
        - The PCE Scope, including the inter-domain functions (inter-
          area, inter-AS, inter-layer), the preferences, and whether the
          PCE can act as default PCE (see Section 4.2)
        - The PCE domains (see Section 4.3)
        - The neighbour PCE domains (see Section 4.4)
        - The PCE capabilities (see Section 4.5)

9.2. Information and Data Model

   A MIB module for PCE Discovery is defined in [PCED-MIB].

9.3. Liveness Detection and Monitoring

   PCE Discovery Protocol liveness detection relies upon OSPF liveness
   detection. OSPF already includes a liveness detection mechanism
   (Hello protocol), and PCE discovery does not require additional
   capabilities.

   Procedures defined in Section 5 allow a PCC to detect when a PCE has
   been deactivated, or is no longer reachable.






Le Roux, Vasseur et al. OSPF extensions for PCE Discovery    [Page 15]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007


9.4. Verify Correct Operations

   The correlation of information advertised against information
   received can be achieved by comparing the information in the PCED TLV
   received by the PCC with that stored at the PCE  using the PCED MIB
   [PCED-MIB].  The number of dropped, corrupt, and rejected information
   elements are available through the PCED MIB.

9.5. Requirements on Other Protocols and Functional Components

   The OSPF extensions defined in this document do not imply any
   requirement on other protocols.

9.6. Impact on Network Operations

   Frequent changes in PCE information advertised in the PCED TLV, may
   have a significant impact on OSPF and might destabilize the operation
   of the network by causing the PCCs to swap between PCEs.

   As discussed in Section 4.10.4 of [RFC4674], it MUST be possible to
   apply at least the following controls:

      - Configurable limit on the rate of announcement of changed
        parameters at a PCE.
      - Control of the impact on PCCs such as through rate-limiting
        the processing of PCED TLVs.
      - Configurable control of triggers that cause a PCC to swap to
        another PCE.

10. Acknowledgments

   We would like to thank Lucy Wong, Adrian Farrel, Les Ginsberg, Mike
   Shand, and Lou Berger for their useful comments and suggestions.

   We would also like to thank Dave Ward, Lars Eggert, Sam Hartman, and
   Tim Polk for their comments during the final stages of publication.

11. References

11.1. Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
   Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2328] Moy, J., "OSPF Version 2", RFC 2328, April 1998.

   [RFC2740] Coltun, R., Ferguson, D., and J. Moy, "OSPF for IPv6",
   RFC 2740, December 1999.

   [RFC2370] Coltun, R., "The OSPF Opaque LSA Option", RFC 2370, July
   1998.


Le Roux, Vasseur et al. OSPF extensions for PCE Discovery    [Page 16]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007


   [RFC3630] Katz, D., Yeung, D., Kompella, K., "Traffic Engineering
   Extensions to OSPF Version 2", RFC 3630, September 2003.

   [OSPF-CAP] Lindem, A., Shen, N., Aggarwal, R., Shaffer, S., Vasseur,
   J.P., "Extensions to OSPF for advertising Optional Router
   Capabilities", draft-ietf-ospf-cap, work in progress.

   [RFC2154] Murphy, S., Badger, M., and B. Wellington, "OSPF with
   Digital Signatures", RFC 2154, June 1997.

11.2. Informative References

   [RFC4657] Ash, J., Le Roux, J.L., "PCE Communication Protocol Generic
   Requirements", RFC4657, September 2006.

   [PCEP] Vasseur, Le Roux, et al., "Path Computation Element (PCE)
   communication Protocol (PCEP) - Version 1", draft-ietf-pce-pcep, work
   in progress.

   [PCED-MIB] Stephan, E., "Definitions of Managed Objects for Path
   Computation Element Discovery", draft-ietf-pce-disc-mib, work in
   progress.

   [PCED-ISIS] Le Roux, Vasseur, et al. "IS-IS protocol extensions for
   Path Computation Element (PCE) Discovery", draft-ietf-pce-disco-
   proto-isis, work in progress.

   [RFC4655] Farrel, A., Vasseur, J.P., Ash, J., "Path Computation
   Element (PCE)-based Architecture", RFC4655, August 2006.

   [RFC4674] Le Roux, J.L., et al. "Requirements for PCE discovery",
   RFC4674, October 2006.

12. Editor's Addresses

   Jean-Louis Le Roux (Editor)
   France Telecom
   2, avenue Pierre-Marzin
   22307 Lannion Cedex
   FRANCE
   Email: jeanlouis.leroux@orange-ftgroup.com

   Jean-Philippe Vasseur (Editor)
   Cisco Systems, Inc.
   1414 Massachusetts avenue
   Boxborough , MA - 01719
   USA
   Email: jpv@cisco.com





Le Roux, Vasseur et al. OSPF extensions for PCE Discovery    [Page 17]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007




13. Contributors' Addresses

   Yuichi Ikejiri
   NTT Communications Corporation
   1-1-6, Uchisaiwai-cho, Chiyoda-ku
   Tokyo 100-8019
   JAPAN
   Email: y.ikejiri@ntt.com


   Raymond Zhang
   BT Infonet
   2160 E. Grand Ave.
   El Segundo, CA 90025
   USA
   Email: raymond_zhang@bt.infonet.com


14. Intellectual Property Statement

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.


   Disclaimer of Validity

   This document and the information contained herein are provided
   on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE
   REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE
   IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL
   WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY

Le Roux, Vasseur et al. OSPF extensions for PCE Discovery    [Page 18]

Internet Draft  draft-ietf-pce-disco-proto-ospf-08.txt    October 2007


   WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE
   ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
   FOR A PARTICULAR PURPOSE.

   Copyright Statement

   Copyright (C) The IETF Trust (2007). This document is subject to the
   rights, licenses and restrictions contained in BCP 78, and except as
   set forth therein, the authors retain all their rights.












































Le Roux, Vasseur et al. OSPF extensions for PCE Discovery    [Page 19]


Html markup produced by rfcmarkup 1.107, available from http://tools.ietf.org/tools/rfcmarkup/