[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits] [IPR]

Versions: (draft-bradford-pce-path-key) 00 01 02 03 04 05 06 RFC 5520

Networking Working Group                              Rich Bradford (Ed)
Internet-Draft                                                JP Vasseur
Intended Status: Standards Track                     Cisco Systems, Inc.
Created: March 7, 2009                                     Adrian Farrel
Expires: September 7, 2009                            Old Dog Consulting


        Preserving Topology Confidentiality in Inter-Domain Path
                Computation Using a Key-Based Mechanism

                   draft-ietf-pce-path-key-06.txt

Status of this Memo

   This Internet-Draft is submitted to IETF in full conformance with
   the provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

Abstract

   Multiprotocol Label Switching (MPLS) and Generalized MPLS (GMPLS)
   Traffic Engineering (TE) Label Switched Paths (LSPs) may be
   computed by Path Computation Elements (PCEs). Where the TE LSP
   crosses multiple domains, such as Autonomous Systems (ASes), the
   path may be computed by multiple PCEs that cooperate, with each
   responsible for computing a segment of the path. However, in some
   cases (e.g., when ASes are administered by separate Service
   Providers), it would break confidentiality rules for a PCE to
   supply a path segment to a PCE in another domain, thus disclosing
   AS-internal topology information. This issue may be circumvented
   by returning a loose hop and by invoking a new path computation
   from the domain boundary Label Switching Router (LSR) during TE
   LSP setup as the signaling message enters the second domain, but
   this technique has several issues including the problem of
   maintaining path diversity.



Bradford, Vasseur and Farrel                                    [Page 1]

draft-ietf-pce-path-key-06.txt                                March 2009

   This document defines a mechanism to hide the contents of a
   segment of a path, called the Confidential Path Segment (CPS). The
   CPS may be replaced by a path-key that can be conveyed in the PCE
   Communication Protocol (PCEP) and signaled within in a Resource
   Reservation Protocol TE (RSVP-TE) explicit route object.

Conventions used in this document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
   NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED",  "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   RFC-2119 [RFC2119].

Table of contents

   1.  Introduction.................................................3
   1.1. Terminology.................................................4
   2.  Path-Key Solution............................................5
   2.1. Mode of Operation...........................................5
   2.2. Example.....................................................6
   3.  PCEP Protocol Extensions.....................................7
   3.1. Path Keys in PCRep Messages.................................7
   3.1.1. PKS with 32-bit PCE ID....................................8
   3.1.2. PKS with 128-bit PCE ID...................................9
   3.2. Unlocking Path Keys.........................................9
   3.2.1. Path Key Bit.............................................10
   3.2.2. PATH-KEY Object..........................................10
   3.2.3. Path Computation Request (PCReq) message with Path Key...10
   4.  PCEP Mode of Operation for Path Key Expansion...............11
   5.  Security Considerations.....................................12
   6.  Manageability Considerations................................13
   6.1. Control of Function Through Configuration and Policy.......13
   6.2. Information and Data Models................................14
   6.3. Liveness Detection and Monitoring..........................14
   6.4. Verifying Correct Operation................................14
   6.5. Requirements on Other Protocols and Functional Components..15
   6.6. Impact on Network Operation................................15
   7.  IANA Considerations.........................................15
   7.1. New Subobjects for the ERO Object..........................15
   7.2. New PCEP Object............................................16
   7.3. New RP Object Bit Flag.....................................16
   7.4. New NO-PATH-VECTOR TLV Bit Flag............................16
   8.  Normative References........................................17
   9.  Informational References....................................17
   10.  Acknowledgements...........................................18
   11.  Authors' Addresses.........................................18





Bradford, Vasseur, and Farrel                                   [Page 2]

draft-ietf-pce-path-key-06.txt                                March 2009

1. Introduction

   Path computation techniques using the Path Computation Element
   (PCE) are described in [RFC4655] and allow for path computation of
   inter-domain Multiprotocol Label Switching (MPLS) Traffic
   Engineering (TE) and Generalized MPLS (GMPLS) Label Switched Paths
   (LSPs).

   An important element of inter-domain TE is that TE information is
   not shared between domains for scalability and confidentiality
   reasons ([RFC4105] and [RFC4216]). Therefore, a single PCE is
   unlikely to be able to compute a full inter-domain path.

   Two path computation scenarios can be used for inter-domain TE
   LSPs: one using per-domain path computation (defined in [RFC5152]),
   and the other using a PCE-based path computation technique with
   cooperation between PCEs (as described in [RFC4655]). In this second
   case, paths for inter-domain LSPs can be computed by cooperation
   between PCEs each of which computes a segment of the path across one
   domain. Such a path computation procedure is described in [BRPC].

   If confidentiality is required between domains (such as would very
   likely be the case between Autonomous Systems (ASes) belonging to
   different Service Providers) then cooperating PCEs cannot exchange
   path segments or else the receiving PCE and the Path Computation
   Client (PCC) will be able to see the individual hops through
   another domain thus breaking the confidentiality requirement
   stated in [RFC4105] and [RFC4216]. We define the part of the path
   which we wish to keep confidential as the Confidential Path
   Segment (CPS).

   One mechanism for preserving the confidentiality of the CPS is for
   the PCE to return a path containing a loose hop in place of the
   segment that must be kept confidential. The concept of loose and
   strict hops for the route of a TE LSP is described in [RFC3209].
   The Path Computation Element Communication Protocol (PCEP) defined
   in [RFC5440] supports the use of paths with loose hops, and it is a
   local policy decision at a PCE whether it returns a full explicit
   path with strict hops or uses loose hops. Note that a Path
   computation Request may request an explicit path with strict hops
   or may allow loose hops as detailed in [RFC5440].

   The option of returning a loose hop in place of the CPS can be
   achieved without further extensions to PCEP or the signaling
   protocol. If loose hops are used, the TE LSPs are signaled as
   normal ([RFC3209]), and when a loose hop is encountered in the
   explicit route it is resolved by performing a secondary path
   computation to reach the resource or set of resources identified
   by the loose hop. Given the nature of the cooperation between PCEs
   in computing the original path, this secondary computation occurs

Bradford, Vasseur, and Farrel                                   [Page 3]

draft-ietf-pce-path-key-06.txt                                March 2009

   at or on behalf of a Label Switching Router (LSR) at a domain
   boundary (i.e., an Area Border Router (ABR) or an AS Border Router
   (ASBR)) and the path is expanded as described in [RFC5152].

   The PCE-based computation model is particularly useful for
   determining mutually disjoint inter-domain paths such as might be
   required for service protection [RFC5298]. A single path computation
   request is used. However, if loose hops are returned, the path of
   each TE LSP must be recomputed at the domain boundaries as the TE
   LSPs are signaled, and since the TE LSP signaling proceeds
   independently for each TE LSP, disjoint paths cannot be guaranteed
   since the LSRs in charge of expanding the EROs are not synchronized.
   Therefore, if the loose hop technique is used without further
   extensions, path segment confidentiality and path diversity are
   mutually incompatible requirements.

   This document defines the notion of a Path Key that is a token
   that replaces a path segment in an explicit route. The Path Key is
   encoded as a Path Key Subobject (PKS) returned in the PCEP Path
   Computation Reply message (PCRep) ([RFC5440]). Upon receiving the
   computed path, the PKS will be carried in an RSVP-TE Path message
   (RSVP-TE [RFC3209] and [RSVP-PKS]) during signaling.

   The BNF in this document follows the format described in [RBNF].

1.1.   Terminology

   This document makes use of the following terminology and acronyms.

   AS: Autonomous System.

   ASBR: Autonomous System Border Routers used to connect to another
   AS of a different or the same Service Provider via one or more
   links inter-connecting between ASes.

   CPS: Confidential Path Segment. A segment of a path that contains
   nodes and links that the AS policy requires to not be disclosed
   outside the AS.

   Inter-AS TE LSP: A TE LSP that crosses an AS boundary.

   LSR: Label Switching Router.

   LSP: Label Switched Path.

   PCC: Path Computation Client: Any client application requesting a
   path computation to be performed by a Path Computation Element.

   PCE: Path Computation Element: An entity (component, application
   or network node) that is capable of computing a network path or

Bradford, Vasseur, and Farrel                                   [Page 4]

draft-ietf-pce-path-key-06.txt                                March 2009

   route based on a network graph and applying computational
   constraints.

   TE LSP: Traffic Engineering Label Switched Path

2. Path-Key Solution

   The Path-Key solution may be applied in the PCE-based path
   computation context as follows. A PCE computes a path segment
   related to a particular domain and replaces any CPS in the path
   reported to the requesting PCC (or another PCE) by one or more
   subobjects referred to as PKSes.  The entry boundary LSR of each
   CPS SHOULD be specified using its TE Router Id as a hop in the
   returned path immediately preceding the CPS, and other sub-objects
   MAY be included in the path immediately before the hop identifying
   the boundary LSR to indicate link and label choices. Where two
   PKSes are supplied in sequence with no intervening nodes, the
   entry node to the second CPS MAY be part of the first CPS and does
   not need to be explicitly present in the returned path. The exit
   node of a CPS MAY be present as a strict hop immediately following
   the PKS.

2.1. Mode of Operation

   During path computation, when local policy dictates that
   confidentiality must be preserved for all or part of the path
   segment being computed or if explicitly requested by the Path
   Computation Request, the PCE associates a path-key with the
   computed path for the CPS, places its own identifier (its PCE ID
   as defined in Section 3.1) along with the path-key in a PKS, and
   inserts the PKS object in the path returned to the requesting PCC
   or PCE immediately after the subobject that identifies (using the
   TE Router Id) the LSR that will expand the PKS into explicit path
   hops.This will usually be the LSR that is the start point of the
   CPS. The PCE that generates a PKS SHOULD store the computed path
   segment and the path-key for later retrieval. A local policy
   SHOULD be used to determine for how long to retain such stored
   information, and whether to discard the information after it has
   been queried using the procedures described below. It is
   RECOMMENDED for a PCE to store the PKS for a period of 10 minutes.

   A path-key value is scoped to the PCE that computed it as
   identified by the PCE-ID carried in the PKS. A PCE MUST NOT re-use
   a path-key value to represent a new CPS for at least 30 minutes
   after discarding the previous use of the same path-key. A PCE that
   is unable to retain information about previously used path-key
   values over a restart SHOULD use some other mechanism to guarantee
   uniqueness of path-key values such as embedding a timestamp or
   version number in the path-key.


Bradford, Vasseur, and Farrel                                   [Page 5]

draft-ietf-pce-path-key-06.txt                                March 2009

   A head-end LSR that is a PCC converts the path returned by a PCE
   into an explicit route object (ERO) that it includes in the
   Resource Reservation Protocol (RSVP) Path message. If the path
   returned by the PCE contains a PKS, this is included in the ERO.
   Like any other subobjects, the PKS is passed transparently from
   hop to hop, until it becomes the first subobject in the ERO. This
   will occur at the start of the CPS which will usually be the
   domain boundary. The PKS MUST be preceded by an ERO subobject that
   identifies the LSR that must expand the PKS. This means that
   (following the rules for ERO processing set out in [RFC3209])
   the PKS will not be encountered in ERO processing until the ERO is
   being processed by the LSR that is capable of correctly handling the
   PKS.

   An LSR that encounters a PKS when trying to identify the next-hop
   retrieves the PCE-ID from the PKS and sends a Path Computation
   Request (PCReq) message as defined in [RFC5440] to the PCE identified
   by the PCE-ID that contains the path-key object .

   Upon receiving the PCReq message, the PCE identifies the computed
   path segment using the supplied path-key, and returns the
   previously computed path segment in the form of explicit hops
   using an ERO object contained in the Path Computation Reply
   (PCReqp) to the requesting node as defined in [RFC5440]. The
   requesting node inserts the explicit hops into the ERO and
   continues to process the TE LSP setup as per [RFC3209].

2.2. Example

    Figure 1 shows a simple two-AS topology with a PCE responsible
    for the path computations in each AS. An LSP is requested from
    the ingress LSR in one AS to the egress LSR in the other AS. The
    ingress, acting as PCC, sends a path computation request to PCE-
    1. PCE-1 is unable to compute an end-to-end path and invokes PCE-
    2 (possibly using the techniques described in [BRPC]). PCE-2
    computes a path segment from ASBR-2 to the egress as {ASBR-2, C,
    D, Egress}. It could pass this path segment back to PCE-1 in
    full, or it could send back the path {ASBR-2, Egress} where the
    second hop is a loose hop.

    However, in order to protect the confidentiality of the topology
    in the second AS while still specifying the path in full, PCE-2
    may send PCE-1 a path segment expressed as {ASBR-2, PKS, Egress}
    where the PKS is a Path Key Subobject as defined in this
    document. In this case, PCE-2 has identified the segment {ASBR-2,
    C, D, Egress} as a Confidential Path Segment (CPS). PCE-1 will
    compute the path segment that it is responsible for, and will
    supply the full path to the PCC as {Ingress, A, B, ASBR-1, ASBR-
    2, PKS, Egress}.


Bradford, Vasseur, and Farrel                                   [Page 6]

draft-ietf-pce-path-key-06.txt                                March 2009

    Signaling proceeds in the first AS as normal, but when the Path
    message reaches ASBR-2 the next hop is the PKS, and this must be
    expanded before signaling can progress further. ASBR-2 uses the
    information in the PKS to request PCE-2 for a path segment, and
    PCE-2 will return the segment {ASBR-2, C, D, Egress} allowing
    signaling to continue to set up the LSP.


    -----------------------------    ----------------------------
   |     -------                 |  |    -------                 |
   |    | PCE-1 |<---------------+--+-->| PCE-2 |                |
   |     -------                 |  |    -------                 |
   |      ^                      |  |    ^                       |
   |      |                      |  |    |                       |
   |      v                      |  |    v                       |
   |  -------              ----  |  |  ----                      |
   | |  PCC  |   -    -   |ASBR| |  | |ASBR|   -    -    ------  |
   | |Ingress|--|A|--|B|--|  1 |-+--+-|  2 |--|C|--|D|--|Egress| |
   |  -------    -    -    ----- |  |  ----    -    -    ------  |
   |                             |  |                            |
    -----------------------------    ----------------------------

   Figure 1 : A Simple network to demonstrate the use of the PKS


3. PCEP Protocol Extensions

3.1. Path Keys in PCRep Messages

   Path Keys are carried in PCReq and PCRep messages as part of the
   various objects that carry path definitions. In particular, a Path
   Key is carried in the Explicit Route Object (ERO) on PCRep
   messages.

   In all cases, the Path Key is carried in a Path Key Subobject
   (PKS).

   The PKS is a fixed-length subobject containing a Path-Key and a
   PCE-ID. The Path Key is an identifier, or token used to represent
   the CPS within the context of the PCE identified by the PCE-ID.
   The PCE-ID identifies the PCE that can decode the Path Key using
   an identifier that is unique within the domain that the PCE
   serves. The PCE-ID has to be mapped to a reachable IPv4 or IPv6
   address of the PCE by the first node of the CPS (usually a domain
   border router) and a PCE MAY use one of its reachable IP addresses
   as its PCE-ID. Alternatively and to provide greater security (see
   Section 5) or increased confidentiality, according to domain-local
   policy, the PCE MAY use some other identifier that is scoped only
   within the domain.


Bradford, Vasseur, and Farrel                                   [Page 7]

draft-ietf-pce-path-key-06.txt                                March 2009

   To allow IPv4 and IPv6 addresses to be carried, two subobjects are
   defined in the following subsections.

   The Path Key Subobject may be present in the PCEP ERO or the PCEP
   PATH-KEY object (see Section 3.2).

3.1.1. PKS with 32-bit PCE ID

   The Subobject Type for the PKS with 32-bit PCE ID is to be
   assigned by IANA (recommended value 64). The format of this
   subobject is as follows:

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |L|    Type     |     Length    |           Path Key            |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                         PCE ID (4 bytes)                      |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

       L

         The L bit SHOULD NOT be set, so that the subobject represents a
         strict hop in the explicit route.

       Type

         Subobject Type for a Path Key with 32-bit PCE ID as assigned by
         IANA.

       Length

         The Length contains the total length of the subobject in bytes,
         including the Type and Length fields.  The Length is always 8.

       PCE ID

         A 32-bit identifier of the PCE that can decode this key. The
         identifier MUST be unique within the scope of the domain that
         the CPS crosses, and MUST be understood by the LSR that will
         act as PCC for the expansion of the PKS. The interpretation of
         the PCE-ID is subject to domain-local policy. It MAY be an IPv4
         address of the PCE that is always reachable, and MAY be an
         address that is restricted to the domain in which the LSR that
         is called upon to expand the CPS lies. Other values that have
         no meaning outside the domain (for example, the Router ID of
         the PCE) MAY be used to increase security or confidentiality
         (see Section 5).



Bradford, Vasseur, and Farrel                                   [Page 8]

draft-ietf-pce-path-key-06.txt                                March 2009

3.1.2. PKS with 128-bit PCE ID

   The Subobject Type for the PKS with 128-bit PCE ID is to be
   assigned by IANA (recommended value 65). The format of the
   subobject is as follows.

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |L|    Type     |     Length    |           Path Key            |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                        PCE ID (16 bytes)                      |
    |                                                               |
    |                                                               |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

       L

         As above.

       Type

         Subobject Type for a Path Key with 128-bit PCE ID as assigned
         by IANA.

       Length

         The Length contains the total length of the subobject in bytes,
         including the Type and Length fields.  The Length is always 20.

       PCE ID

         A 128-bit identifier of the PCE that can decode this key. The
         identifier MUST be unique within the scope of the domain that
         the CPS crosses, and MUST be understood by the LSR that will
         act as PCC for the expansion of the PKS. The interpretation of
         the PCE-ID is subject to domain-local policy. It MAY be an IPv6
         address of the PCE that is always reachable, but MAY be an
         address that is restricted to the domain in which the LSR that
         is called upon to expand the CPS lies. Other values that have
         no meaning outside the domain (for example, the IPv6 TE Router
         ID) MAY be used to increase security (see Section 5).

3.2. Unlocking Path Keys

   When a network node needs to decode a Path Key so that it can
   continue signaling for an LSP, it must send a PCReq to the
   designated PCE. The PCReq defined in [RFC5440] needs to be modified
   to support this usage which differs from the normal path

Bradford, Vasseur, and Farrel                                   [Page 9]

draft-ietf-pce-path-key-06.txt                                March 2009

   computation request. To that end, a new flag is defined to show
   that the PCReq relates to the expansion of a PKS, and a new object
   is defined to carry the PKS in the PCReq. These result in an
   update to the BNF for the message. The BNF used in this document is
   as described in [RBNF].

3.2.1. Path Key Bit

   [RFC5440] defines the Request Parameters (RP) object that is used to
   specify various characteristics of the path computation request
   (PCReq).

   In this document we define a new bit named the Path Key bit as
   follows. See Section 7.3 for the IANA assignment of the
   appropriate bit number.

   Path Key bit: When set, the requesting PCC requires the retrieval
   of a Confidential Path Segment that corresponds to the PKS carried
   in a PATH_KEY object in the path computation request. The Path Key
   bit MUST be cleared when the path computation request is not
   related to a CPS retrieval.

3.2.2. PATH-KEY Object

   When a PCC needs to expand a path-key in order to expand a CPS it
   issues a path computation request (PCReq) to the PCE identified in
   the PKS in the RSVP-TE ERO that it is processing. The PCC supplies
   the PKS to be expanded in a PATH-KEY Object in the PCReq message.

   The PATH-KEY Object is defined as follows.

   PATH-KEY Object-Class is to be assigned by IANA (recommended
   value=16)

   Path Key Object-Type is to be assigned by IANA (recommended
   value=1)

   The PATH-KEY Object MUST contain at least one Path Key Subobject
   (see Section 3.1). The first PKS MUST be processed by the PCE.
   Subsequent subobjects SHOULD be ignored.

3.2.3. Path Computation Request (PCReq) message with Path Key

   The format of a PCReq message including a PATH-KEY object is
   unchanged as follows:

      <PCReq Message>::= <Common Header>
                         [<SVEC-list>]
                         <request-list>



Bradford, Vasseur, and Farrel                                  [Page 10]

draft-ietf-pce-path-key-06.txt                                March 2009

      where:
         <svec-list>::=<SVEC>[<svec-list>]
         <request-list>::=<request>[<request-list>]

   To support the use of the message to expand a PKS, the definition
   of <request> is modified as follows :

      <request>::= <RP>
                   <segment-computation> | <path-key-expansion>

      where:
         <segment-computation> ::= <END-POINTS>
                                   [<LSPA>]
                                   [<BANDWIDTH>]
                                   [<BANDWIDTH>]
                                   [<metric-list>]
                                   [<RRO>]
                                   [<IRO>]
                                   [<LOAD-BALANCING>]
         <path-key-expansion> ::= <PATH-KEY>

   Thus, the format of the message for use in normal path computation
   is unmodified.

4. PCEP Mode of Operation for Path Key Expansion

   The retrieval of the explicit path (the CPS) associated with a PKS
   by a PCC is no different than any other path computation request
   with the exception that the PCReq message MUST contain a PATH_KEY
   object and the Path Key bit of the RP object MUST the set. On
   receipt of a PCRep containing a CPS, the requesting PCC SHOULD
   use insert the CPS into the ERO that it will signal, in accordance
   with local policy.

   If the receiving PCE does not recognize itself as identified by the
   PCE ID carried in the PKS it MAY forward the PCReq message to
   another PCE according to local policy. If the PCE does not forward
   such a PCReq, it MUST respond with a PCRep message containing a NO-
   PATH object.

   If the receiving PCE recognizes itself, but cannot find the
   related CPS, or if the retrieval of the CPS is not allowed by
   policy, the PCE MUST send a PCRep message that contains a NO-PATH
   object. The NO-PATH-VECTOR TLV SHOULD be used as described in
   [RFC5440] and a new bit-number (see Section 7.4) is assigned to
   indicate "Cannot expand PKS".

   Upon receipt of a negative reply, the requesting LSR MUST fail the
   LSP setup and SHOULD use the procedures associated with loose hop
   expansion failure [RFC3209].

Bradford, Vasseur, and Farrel                                  [Page 11]

draft-ietf-pce-path-key-06.txt                                March 2009

5. Security Considerations

   This document describes tunneling confidential path information
   across an untrusted domain (such as an AS). There are many
   security considerations that apply to PCEP and RSVP-TE.

   Issues include:

   - Confidentiality of the CPS (can other network elements probe for
     expansion of path-keys, possibly at random?).

   - Authenticity of the path-key (resilience to alteration by
     intermediaries, resilience to fake expansion of path-keys).

   - Resilience from DoS attacks (insertion of spurious path-keys;
     flooding of bogus path-key expansion requests).

   Most of the interactions required by this extension are point to
   point, can be authenticated and made secure as described in [RFC5440]
   and [RFC3209]. These interactions include the:

       - PCC->PCE request
       - PCE->PCE request(s)
       - PCE->PCE response(s)
       - PCE->PCC response
       - LSR->LSR request and response (Note that a rogue LSR could
         modify the ERO and insert or modify Path Keys. This would
         result in an LSR (which is downstream in the ERO) sending
         decode requests to a PCE. This is actually a larger problem
         with RSVP.  The rogue LSR is an existing issue with RSVP and
         will not be addressed here.
       - LSR->PCE request. Note that the PCE can check that the LSR
         requesting the decode is the LSR at the head of the Path Key.
         This largely contains the previous problem to DoS rather than
         a security issue. A rogue LSR can issue random decode
         requests, but these will amount only to DoS.
       - PCE->LSR response.

   Thus, the major security issues can be dealt with using standard
   techniques for securing and authenticating point-to-point
   communications. In addition, it is recommended that the PCE
   providing a decode response should check that the LSR that issued
   the decode request is the head end of the decoded ERO segment.

   Further protection can be provided by using a PCE ID to identify
   the decoding PCE that is only meaningful within the domain that
   contains the LSR at the head of the CPS. This may be an IP address
   that is only reachable from within the domain, or some not-address
   value. The former requires configuration of policy on the PCEs,
   the latter requires domain-wide policy.

Bradford, Vasseur, and Farrel                                  [Page 12]

draft-ietf-pce-path-key-06.txt                                March 2009

6. Manageability Considerations

6.1. Control of Function Through Configuration and Policy

   The treatment of a path segment as a CPS, and its substitution in
   a PCReq ERO with a PKS, is a function that MUST be under operator
   and policy control where a PCE supports the function. The operator
   MUST be given the ability to specify which path segments are to be
   replaced and under what circumstances. For example, an operator
   might set a policy that states that every path segment for the
   operator's domain will be replaced by a PKS when the PCReq has
   been issued from outside the domain.

   The operation of the PKS extensions require that path-keys are
   retained by the issuing PCE to be available for retrieval by an
   LSR (acting as a PCC) at a later date. But it is possible that the
   retrieval request will never be made, so good housekeeping
   requires that a timer is run to discard unwanted path-keys. A
   default value for this timer is suggested in Section 2.1.
   Implementations SHOULD provide the ability for this value to be over-
   ridden through operator configuration or policy.

   After a PKS has been expanded in response to a retrieval request,
   it may be valuable to retain the path-key and CPS for debug
   purposes. Such retention SHOULD NOT be the default behavior of an
   implementation, but MAY be available in response to operator request.

   Once a path-key has been discarded, the path-key value SHOULD NOT
   be immediately available for re-use for a new CPS since this might
   lead to accidental misuse. A default timer value is suggested in
   Section 2.1. Implementations SHOULD provide the ability for this
   value to be over-ridden through operator configuration or policy.

   A PCE must set a PCE-ID value in each PKS it creates so that PCCs
   can correctly identify it and send PCReq messages to expand the
   PKS to a path segment. A PCE implementation SHOULD allow operator
   or policy control of the value to use as the PCE-ID. If the PCE
   allows PCE-ID values that are not routable addresses to be used,
   the PCCs MUST be configurable (by the operator or through policy)
   to allow them to map from the PCE-ID to a routable address of the
   PCE. Such mapping may be algorithmic, procedural (for example,
   mapping a PCE-ID equal to the IGP Router ID into a routable
   address), or configured through a local or remote mapping table.








Bradford, Vasseur, and Farrel                                  [Page 13]

draft-ietf-pce-path-key-06.txt                                March 2009

6.2. Information and Data Models

   A MIB module for PCEP is already defined in [PCEP-MIB]. The
   configurable items listed in Section 6.1 MUST be added as readable
   objects in the module and SHOULD be added as writable objects.

   A new MIB module MUST be created to allow inspection of path-keys.
   For a given PCE, this MIB module MUST provide a mapping from path-
   key to path segment (that is, a list of hops), and MUST supply
   other information including:

   - The identity of the PCC that issued the original request that
     led to the creation of the path-key.
   - The request ID of the original PCReq.
   - Whether the path-key has been retrieved yet, and if so, by which
     PCC.
   - How long until the path segment associated with the path-key
     will be discarded.
   - How long until the path-key will be available for re-use.

6.3. Liveness Detection and Monitoring

   The procedures in this document extend PCEP, but do not introduce
   new interactions between network entities. Thus, no new liveness
   detection or monitoring is required.

   It is possible that a head-end LSR that has be given a path
   including PKSs replacing specific CPSs will want to know whether
   the path-keys are still valid (or have timed out). However, rather
   than introduce a mechanism to poll the PCE that is responsible for
   the PKS, it is considered pragmatic to simply signal the
   associated LSP.

6.4. Verifying Correct Operation

   The procedures in this document extend PCEP, but do not introduce
   new interactions between network entities. Thus, no new tools for
   verifying correct operation are required.

   A PCE SHOULD maintain counters and logs of the following events
   that might indicate incorrect operation (or might indicate
   security issues).

   - Attempts to expand an unknown path-key.
   - Attempts to expand an expired path-key.
   - Duplicate attempts to expand the same path-key.
   - Expiry of path-key without attempt to expand it.




Bradford, Vasseur, and Farrel                                  [Page 14]

draft-ietf-pce-path-key-06.txt                                March 2009

6.5. Requirements on Other Protocols and Functional Components

   The procedures described in this document require that the LSRs
   signal PKSs as defined in [RSVP-PKS]. Note that the only changes
   to LSRs are at the PCCs. Specifically, changes are only needed at
   the head-end LSRs that build RSVP-TE Path messages containing
   Path-Key Subobjects in their EROs, and the LSRs that discover such
   subobjects as next hops and must expand them. Other LSRs in the
   network, even if they are on the path of the LSP, will not be
   called upon to process the PKS.

6.6. Impact on Network Operation

   As well as the security and confidentiality aspects addressed by
   the use of the PKS, there may be some scaling benefits associated
   with the procedures described in this document. For example, a
   single PKS in an explicit route may substitute for many subobjects
   and can reduce the overall message size correspondingly. In some
   circumstances, such as when the explicit route contains multiple
   subobjects for each hop (including node IDs, TE link IDs,
   component link IDs for each direction of a bidirectional LSP, and
   label IDs for each direction of a bidirectional LSP) or when the
   LSP is a point-to-multipoint LSP, this scaling improvement may be
   very significant.

   Note that a PCE will not supply a PKS unless it is knows that the
   LSR that will receive the PKS through signaling will be able to
   handle it. Furthermore, as noted in Section 6.5, only those LSRs
   specifically called upon to expand the PKS will be required to
   process the subobjects during signaling. Thus, the only backward
   compatibility issues associated with the procedures introduced in
   this document arise when a head-end LSR receives a PCRep with an
   ERO containing a PKS and does not know how to encode this into
   signaling.

   Since the PCE that inserted the PKS requires to keep the CPS
   confidential, the legacy head-end LSR cannot be protected. It must
   either fail the LSP setup, or request a new path computation
   avoiding the domain that has supplied it with unknown subobjects.

7. IANA Considerations

   IANA assigns values to PCEP parameters in registries defined in
   [RFC5440]. IANA is requested to make the following additional
   assignments.

7.1. New Subobjects for the ERO Object

   IANA has previously assigned an Object-Class and Object-Type to
   the ERO carried in PCEP messages [RFC5440]. IANA also maintains a

Bradford, Vasseur, and Farrel                                  [Page 15]

draft-ietf-pce-path-key-06.txt                                March 2009

   list of subobject types valid for inclusion in the ERO.

   IANA is requested to assign two new subobject types for inclusion
   in the ERO as follows:

   Subobject Type
             64   Path Key with 32-bit PCE ID             [This.I-D]
             65   Path Key with 128-bit PCE ID            [This.I-D]

7.2. New PCEP Object

   IANA is requested to assign a new object class in the registry of
   PCEP Objects as follows.

   Object  Name          Object  Name                       Reference
   Class                 Type

   16    PATH-KEY        1     Path Key                   [This.I-D]

       Subobjects
          This object may carry the following subobjects as defined
          for the ERO object.

                  64   Path Key with 32-bit PCE ID        [This.I-D]
                  65   Path Key with 128-bit PCE ID       [This.I-D]

7.3. New RP Object Bit Flag

   IANA maintains a registry of bit flags carried in the PCEP RP
   object as defined in [RFC5440]. IANA is requested to assign a new bit
   flag as follows:

   Bit      Hex     Name                                 Reference
   Number
   15     0x000100  Path Key (P-bit)                     [This.I-D]

7.4. New NO-PATH-VECTOR TLV Bit Flag

   IANA maintains a registry of bit flags carried in the PCEP NO-
   PATH-VECTOR TLV in the PCEP NO-PATH object as defined in [RFC5440].
   IANA is requested to assign a new bit flag as follows:

   Bits Number      Name Flag                    Reference
        1             PKS expansion failure        [This.I-D]







Bradford, Vasseur, and Farrel                                  [Page 16]

draft-ietf-pce-path-key-06.txt                                March 2009

8. Normative References

   [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
             Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC5440] Vasseur, J.P., Le Roux, J.L., Ayyangar, A., Oki, E.,
             Ikejiri, A., Atlas, A., Dolganow, A., "Path Computation
             Element (PCE) Communication Protocol (PCEP)", RFC 5440,
             March 2009.

9. Informative References

   [RFC3209] Awduche, Berger, Gan, Li, Srinivasan and Swallow, "RSVP-TE:
             Extensions to RSVP for LSP Tunnels", RFC 3209, December
             2001.

   [RFC4105] Le Roux, J., Vasseur, JP., Boyle, J., "Requirements for
             Support of Inter-Area and Inter-AS MPLS Traffic
             Engineering", RFC 4105, June 2005.

   [RFC4216] Zhang, R., Vasseur, JP., et. al., "MPLS Inter-AS Traffic
             Engineering requirements", RFC 4216, November 2005.

   [RFC4655] Farrel, Vasseur, & Ash, "A Path Computation Element (PCE)-
             Based Architecture", RFC 4655, August 2006.

   [RFC5152] Vasseur, JP., et al "A Per-Domain Path Computation Method
             for Establishing Inter-Domain Traffic Engineering (TE)
             Label Switched Paths (LSPs)", RFC 5152, Fenruary 2008.

   [RFC5298] Takeda, T., et al, "Analysis of Inter-domain Label
             Switched Path (LSP) Recovery", RFC 5298, August 2008.

   [RSVP-PKS] Bradford, R., Vasseur, JP., Farrel, A., "RSVP Extensions
             for Path Key Support", draft-ietf-ccamp-path-key-ero,
             work in progress.

   [BRPC]    Vasseur, JP., et al "A Backward Recursive PCE-based
             Computation (BRPC) procedure to compute shortest inter-
             domain Traffic Engineering Label Switched Path", draft-
             ietf-pce-brpc, work in progress.

   [PCEP-MIB] Kiran Koushik, A., and Stephan, E., "PCE communication
             protocol (PCEP) Management Information Base", draft-
             ietf-pce-pcep-mib, work in progress.

   [RBNF]    Farrel, A., "Reduced Backus-Naur Form (RBNF) A Syntax Used
             in Various Protocol Specifications", draft-farrel-rtg-
             common-bnf, work in progress.

Bradford, Vasseur, and Farrel                                  [Page 17]

draft-ietf-pce-path-key-06.txt                                March 2009

10. Acknowledgements

   The authors would like to thank Eiji Oki, Ben Campbell, and Ross
   Callon for their comments on this document.

11. Authors' Addresses

   Rich Bradford (Editor)
   Cisco Systems, Inc.
   1414 Massachusetts Avenue
   Boxborough, MA - 01719
   USA
   EMail: rbradfor@cisco.com

   Jean-Philippe Vasseur
   Cisco Systems, Inc.
   1414 Massachusetts Avenue
   Boxborough, MA - 01719
   USA
   EMail: jpv@cisco.com

   Adrian Farrel
   Old Dog Consulting
   EMail: adrian@olddog.co.uk

Intellectual Property

   The IETF Trust takes no position regarding the validity or scope of
   any Intellectual Property Rights or other rights that might be
   claimed to pertain to the implementation or use of the technology
   described in any IETF Document or the extent to which any license
   under such rights might or might not be available; nor does it
   represent that it has made any independent effort to identify any
   such rights.

   Copies of Intellectual Property disclosures made to the IETF
   Secretariat and any assurances of licenses to be made available, or
   the result of an attempt made to obtain a general license or
   permission for the use of such proprietary rights by implementers or
   users of this specification can be obtained from the IETF on-line IPR
   repository at http://www.ietf.org/ipr

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   any standard or specification contained in an IETF Document. Please
   address the information to the IETF at ietf-ipr@ietf.org.

   The definitive version of an IETF Document is that published by, or
   under the auspices of, the IETF. Versions of IETF Documents that are

Bradford, Vasseur, and Farrel                                  [Page 18]

draft-ietf-pce-path-key-06.txt                                March 2009

   published by third parties, including those that are translated into
   other languages, should not be considered to be definitive versions
   of IETF Documents. The definitive version of these Legal Provisions
   is that published by, or under the auspices of, the IETF. Versions of
   these Legal Provisions that are published by third parties, including
   those that are translated into other languages, should not be
   considered to be definitive versions of these Legal Provisions.

   For the avoidance of doubt, each Contributor to the IETF Standards
   Process licenses each Contribution that he or she makes as part of
   the IETF Standards Process to the IETF Trust pursuant to the
   provisions of RFC 5378. No language to the contrary, or terms,
   conditions or rights that differ from or are inconsistent with the
   rights and licenses granted under RFC 5378, shall have any effect and
   shall be null and void, whether published or posted by such
   Contributor, or included with or in such Contribution.

Disclaimer of Validity

   All IETF Documents and the information contained therein are provided
   on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE
   REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE
   IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL
   WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
   WARRANTY THAT THE USE OF THE INFORMATION THEREIN WILL NOT INFRINGE
   ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
   FOR A PARTICULAR PURPOSE.

Full Copyright Statement

   Copyright (c) 2009 IETF Trust and the persons identified as the
   document authors. All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents in effect on the date of
   publication of this document (http://trustee.ietf.org/license-info).
   Please review these documents carefully, as they describe your
   rights and restrictions with respect to this document.

   This document may contain material from IETF Documents or IETF
   Contributions published or made publicly available before November
   10, 2008.  The person(s) controlling the copyright in some of this
   material may not have granted the IETF Trust the right to allow
   modifications of such material outside the IETF Standards Process.
   Without obtaining an adequate license from the person(s)
   controlling the copyright in such materials, this document may not
   be modified outside the IETF Standards Process, and derivative
   works of it may not be created outside the IETF Standards Process,
   except to format it for publication as an RFC or to translate it
   into languages other than English.

Bradford, Vasseur, and Farrel                                  [Page 19]


Html markup produced by rfcmarkup 1.108, available from http://tools.ietf.org/tools/rfcmarkup/