[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: (draft-farinacci-pim-anycast-rp) 00 01 02 03 04 05 06 07 RFC 4610

Network Working Group                                     Dino Farinacci
INTERNET-DRAFT                                          Procket Networks
Expiration Date: May 2004                                      Yiqun Cai
                                                           cisco Systems
                                                        November 9, 2003


                          Anycast-RP using PIM
                   <draft-ietf-pim-anycast-rp-00.txt>


Status of this Memo

   This document is an Internet-Draft and is in full conformance with
   all provisions of Section 10 of RFC2026.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.


Copyright Notice

   Copyright (C) The Internet Society (2002).  All Rights Reserved.


Abstract

   This proposal allows Anycast-RP to be used inside a domain which runs
   PIM only. There are no other multicast protocols required to support
   Anycast-RP, such as MSDP, which has been used traditionally to solve
   this problem.







Farinacci, Cai                                                  [Page 1]

Internet Draft            Anycast-RP using PIM             November 2003


1. Introduction

   Anycast-RP as described in [2] is a mechanism ISP-based backbones
   have used to get fast convergence when a PIM Rendezvous Point (RP)
   router fails. To allow receivers and sources to Rendezvous to the
   closest RP, the packets from a source needs to get to all RPs to find
   joined receivers.

   This notion of receivers finding sources is the fundamental problem
   of source discovery which MSDP was intended to solve. However, if one
   would like to retain the Anycast-RP benefits from [2] with less
   protocol machinery, removing MSDP from the solution space is an
   option.

   This draft extends the Register mechanism in PIM so Anycast-RP
   functionality can be retained without using MSDP.


2. Requirements

   o Each router acting as an RP MUST be configured with a loopback
     interface using the same (shared) IP address. This address is used to
     tell other routers in the PIM domain, what IP address to use for the
     RP address.

   o The RP address or a prefix that covers the RP address is injected
     into the unicast routing system inside of the domain.

   o Each RP configures all other RPs used in the Anycast-RP set. This
     must be consistently configured in all RPs in the set.


3. Mechanism

   The following diagram illustrates a domain using 3 RPs where
   receivers are joining to the closest RP according to where unicast
   routing metrics take them and 2 sources sending packets to their
   respective RPs.

         S1-----RP1              RP2                RP3------S3
                / \               |
               /   \              |
              R1   R1'            R2

   Assume the above scenario is completely connected where R1, R1', and
   R2 are receivers for a group, and S1 and S2 send to that group.
   Assume RP1, RP2 and RP3 are all assigned the same IP address which is
   used as the Anycast-RP address (let's say the IP address is RPA).



Farinacci, Cai                                                  [Page 2]

Internet Draft            Anycast-RP using PIM             November 2003


   The following procedure is used when S1 starts sourcing traffic:

   o S1 sends a multicast packet.

   o The DR directly attached to S1 will form a PIM Register message to
     send to RP1. The IP address to use is the Anycast-RP address.

   o RP1 will receive the PIM Register message, decapsulate it, send the
     packet down the shared-tree to get the packet to receivers R1 and R1'.

   o RP1 is configured with RP2 and RP3's IP address. It will forward the
     Register message from S1's DR to both of them. RP1 will include
     it's own IP address as the source address for the PIM Register
     message.

   o RP1 sends a Register-Stop back to the DR.

   o RP1 MAY join back to the source-tree by triggering a (S1,G) Join
     message toward S1. However, RP1 MUST create (S1,G) state.

   o RP2 receives the Register message from RP1, decapsulates it, and
     also sends the packet down the shared-tree to get the packet to
     receiver R2.

   o RP2 sends a Register-Stop back to the RP1.

   o RP2 MAY join back to the source-tree by triggering a (S1,G) Join
     message toward S1. However, RP2 MUST create (S1,G) state.

   o RP3 receives the Register message from RP1, decapsulates it, but
     since there is no receivers joined for the group, it can discard
     the packet.

   o RP3 sends a Register-Stop back to the RP1.

   o RP3 creates (S1,G) state so when a receiver joins after S1 starts
     sending, RP3 can join quickly to the source-tree for S1.

   The procedure for S3 sending follows the same as above but it is RP3
   which forwards the Register originated by S3's DR to RP1 and RP2.
   Therefore, this example shows how sources anywhere in the domain,
   associated with different RPs, can reach all receivers, also
   associated with different RPs, in the same domain.


4. Observations and Guidelines about this Proposal

   o An RP will forward a Register only if the Register is received



Farinacci, Cai                                                  [Page 3]

Internet Draft            Anycast-RP using PIM             November 2003


     from an IP address not in the Anycast-RP list (i.e. the Register
     came from a DR and not another RP).

   o Each DR that PIM registers for a source will send the message to it's
     closest RP address. Therefore there are no changes to the DR logic.

   o Packets flow to all receivers no matter what RP they have joined to.

   o The source gets Registered to a single RP by the DR, it's the
     responsibility of the RP, the DR selects, to get the packet to all
     other RPs in the Anycast-RP set.

   o Logic is changed only in the RPs. The logic change is for forwarding
     Register messages. Register-Stop processing is unchanged. However, an
     implementation MAY suppress sending Register-Stop messages in response
     to a Register received from an RP.

   o The rate-limiting of Register and Register-Stop messages are done
     end-to-end. That is from DR -> RP1 -> {RP2 and RP3}. There is no need for
     specific rate-limiting logic between the RPs.

   o When topology changes occur, the existing source-tree adjusts as it
     does today according to [1]. The existing shared-trees, as well,
     adjust as it does today according to [1].

   o Physical RP changes are as fast as unicast route convergence.
     Retaining the benefit of [2].

   o An RP that doesn't support this draft can be mixed with RPs that do
     support this draft. However, the non-supporter RPs should not have
     sources registering to it but may have receivers joined to it.

   o If Null Registers are sent (Registers with an IP header and no IP
     payload), they MUST be replicated to all of the RPs in the Anycast-RP
     set so that source state remains alive for active sources.

   o The number of RPs in the Anycast-RP set should remain small so the
     amount of non-native replication is kept to a minimum.



5. Possible Configuration Language

A possible set of commands to be used could be:

    ip pim anycast-rp <anycast-rp-addr> <rp-addr>

Where:



Farinacci, Cai                                                  [Page 4]

Internet Draft            Anycast-RP using PIM             November 2003


    <anycast-rp-addr> describes the Anycast-RP set for the RP which
    is assigned to the group range. This IP address is the address
    that first-hop and last-hop PIM routers use to register and join
    to.

    <rp-addr> describes the IP address where Register messages are
    forwarded to. This IP address is any address assigned to the RP
    router not including the <anycast-rp-addr>.

Example:

    From the illustration above, the configuration commands would be:

    ip pim anycast-rp RPA RP1
    ip pim anycast-rp RPA RP2
    ip pim anycast-rp RPA RP3

Comment:

    It may be useful to include the local router's IP address in the
    command set so the above lines can be cut-and-pasted or scripted
    into all the RPs in the Anycast-RP set.

    But the implementation would have to be aware of it's own address
    and not inadvertently send a Register to itself.


6. Interaction with MSDP running in an Anycast-PIM Router


   The objective of this Anycast-PIM proposal is to remove the
   dependence on using MSDP. This can be achieved by removing MSDP
   peering between the Anycast RPs. However, to advertise internal
   sources to routers outside of a PIM routing domain and to learn
   external sources from other routing domains, MSDP may still be
   required.

   In this capacity, when there are internal sources that need to be
   advertised externally, an Anycast-RP which receives a Register
   message, either from a DR or an Anycast-RP, should process it as
   described in this specification as well as how to process a Register
   message as described in [2]. That means an SA for the same internal
   source could be originated by multiple Anycast-RPs doing the MSDP
   peering. If this is not desirable, configuration of one or more
   (rather than all) Anycast-RP MSDP routers would be the only ones to
   originate SAs for internal sources. And in some situations, there is
   a good possibility not all Anycast-RPs in the set will have MSDP
   peering sessions so this issue can be mitigated to a certain extent.



Farinacci, Cai                                                  [Page 5]

Internet Draft            Anycast-RP using PIM             November 2003


   From an Anycast-RP perspective, a source should be considered
   internal to a domain, when it is discovered by an Anycast-RP through
   a received Register message. Regardless, if the Register message was
   sent by a DR, another Anycast-RP member, or the router itself.

   For learning sources external to a domain, the MSDP SA messages could
   arrive to multiple MSDP-peering Anycast-RPs. If data does not
   accompany the SA, follow the rules documented in [2]. That is, have
   PIM send a (S,G) join towards the source. If data accompanies the SA,
   duplicate packets could be delivered to receivers (since each RP
   would deliver the packet down each of their respective shared-trees).
   To avoid this, only the highest IP address RP in the Anycast-RP set
   will deliver the SA-data-encapsulated packets down it's shared tree.
   To reach other share-trees rooted at the other Anycast-RPs, the
   highest IP addressed router will create a Register message and
   forward packet to the set of RPs in the Anycast-RP set as it would as
   a functioning DR receiving packets from a directly connected source.
   If not all routers in the Anycast-RP set are MSDP peering routers,
   then configuration is required to identify which members are MSDP
   peers, and the highest IP address of this subset will be used to
   create and originate the Register message.

   Within a routing domain, it is recommended that an Anycast-RP set
   defined in this specification should not be mixed with MSDP peering
   amoung the members. In some cases, the source discovery will work but
   it may not be obvious to the implementations what sources are local
   to the domain and which are not. This may affect external MSDP
   advertisement of internal sources.

   Having said that, this draft makes no attempt to connect MSDP peering
   domains together by using Anycast-PIM inside a transit domain.




















Farinacci, Cai                                                  [Page 6]

Internet Draft            Anycast-RP using PIM             November 2003


7. Acknowledgments

   The authors would like to thank Yiqun Cai and Dino Farinacci for
   prototyping this draft in the cisco IOS implementation and Procket
   implementation, respectively.

   The authors would like to thank John Zwiebel for doing
   interoperability testing of the two prototype implementations.

   And finally, the authors would like to thank Greg Shepard and Lenny
   Giuliano for comments on the draft.


8. Author Information

   Dino Farinacci
   Procket Networks
   dino@procket.com

   Yiqun Cai
   cisco Systems
   ycai@cisco.com



9. References

   [1] Estrin, et al., "Protocol Independent Multicast-Sparse Mode (PIM-
       SM): Protocol Specification", RFC 2362, June 1998.

   [2] Kim, Meyer, Kilmer, Farinacci, "Anycast RP mechanism using PIM
       and MSDP", Internet Draft draft-ietf-mboned-anycast-rp-08.txt,
       May 2001.


















Farinacci, Cai                                                  [Page 7]


Html markup produced by rfcmarkup 1.107, available from http://tools.ietf.org/tools/rfcmarkup/