[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 RFC 4815

Network Working Group                                       L-E. Jonsson
INTERNET-DRAFT                                               K. Sandlund
TO UPDATE: RFC 3095, 3241, 3843, 4019, 4362                 G. Pelletier
Expires: November 2006                                         P. Kremer
                                                                Ericsson
                                                            May 22, 2006


                      RObust Header Compression (ROHC):
                 Corrections and Clarifications to RFC 3095
                   <draft-ietf-rohc-rtp-impl-guide-19.txt>

Status of this memo

   By submitting this Internet-Draft, each author represents that any
   applicable patent or other IPR claims of which he or she is aware
   have been or will be disclosed, and any of which he or she becomes
   aware will be disclosed, in accordance with Section 6 of BCP 79.

   By submitting this Internet-Draft, each author accepts the provisions
   of Section 3 of BCP 78.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups. Note that other
   groups may also distribute working documents as Internet-Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time. It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress".

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/1id-abstracts.html

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html

   This document is a submission of the IETF ROHC WG. Comments should be
   directed to the ROHC WG mailing list, rohc@ietf.org.

Abstract

   RFC 3095 defines the RObust Header Compression (ROHC) framework and
   profiles for IP, UDP, RTP, and ESP. Some parts of the specification
   are unclear or contain errors that may lead to misinterpretations
   that may impair interoperability between different implementations.
   This document provides corrections, additions and clarifications to
   RFC 3095; this document thus updates RFC 3095. In addition, other
   clarifications related to RFC 3241 (ROHC over PPP), RFC 3843 (ROHC IP
   profile) and RFC 4109 (ROHC UPD-Lite profiles) are also provided.



Jonsson, et al.                                                 [Page 1]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


Table of Contents

   1. Introduction and terminology.....................................3
   2. CRC calculation and coverage.....................................4
      2.1. CRC calculation.............................................4
      2.2. Padding octet and CRC calculations..........................4
      2.3. CRC coverage in CRC feedback options........................4
      2.4. CRC coverage of the ESP NULL header.........................5
   3. Mode transition..................................................5
      3.1. Feedback during mode transition to U- and O-mode............5
         3.1.1. Mode transition procedures allowing sparse feedback....5
         3.1.2. Transition from Reliable to Optimistic mode............6
         3.1.3. Transition to Unidirectional mode......................7
      3.2. Feedback during mode transition.............................7
      3.3. Packet decoding during mode transition......................8
   4. Timestamp encoding...............................................8
      4.1. Encoding used for compressed TS bits........................8
      4.2. (De)compression of TS without transmitted TS bits...........9
      4.3. Interpretation intervals for TS encoding...................10
      4.4. TS_STRIDE for scaled timestamp encoding....................10
      4.5. TS wraparound with scaled timestamp encoding...............11
      4.6. Recalculating TS_OFFSET....................................12
      4.7. TS_STRIDE and the Tsc flag in Extension 3..................12
      4.8. Using timer-based compression..............................13
   5. List compression................................................13
      5.1. CSRC list items in RTP dynamic chain.......................13
      5.2. Multiple occurrences of the CC field.......................14
      5.3. Bit masks in list compression..............................14
      5.4. Headers compressed with list compression...................14
      5.5. ESP NULL header list compression...........................15
      5.6. Translation tables and indexes for IP extension headers....15
      5.7. Reference list.............................................15
      5.8. Compression of AH and GRE sequence numbers.................16
   6. Updating properties.............................................17
      6.1. Implicit updates...........................................17
      6.2. Updating properties of UO-1*...............................17
      6.3. Context updating properties for IR packets.................18
      6.4. RTP padding field (R-P) in extension 3.....................18
      6.5. RTP eXtension bit (X) in dynamic part......................18
   7. Context management and CID/context re-use.......................19
      7.1. Persistence of decompressor contexts.......................19
      7.2. CID/context re-use.........................................19
         7.2.1. Re-using a CID/context with the same profile..........20
         7.2.2. Re-using a CID/context with a different profile.......20
   8. Other protocol clarifications...................................21
      8.1. Meaning of NBO.............................................21
      8.2. IP-ID......................................................21
      8.3. Extension-3 in UOR-2* packets..............................21
      8.4. Multiple occurrences of the M bit..........................21
      8.5. Multiple SN options in one feedback packet.................22
      8.6. Multiple CRC options in one feedback packet................22



Jonsson, et al.                                                 [Page 2]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


      8.7. Responding to lost feedback links..........................22
      8.8. UOR-2 in profile 0x0002 (UDP) and profile 0x0003 (ESP).....23
      8.9. Sequence number LSB's in IP extension headers..............23
      8.10. Expecting UOR-2 ACKs in O-mode............................23
   9. ROHC negotiation................................................23
   10. PROFILES suboption in ROHC-over-PPP............................24
   11. Constant IP-ID encoding in IP-only and UPD-Lite profiles.......24
   12. Security considerations........................................24
   13. IANA considerations............................................24
   14. Acknowledgment.................................................24
   15. References.....................................................25
      15.1. Normative References......................................25
      15.2. Informative References....................................25
   16. Authors' Addresses.............................................26
   Appendix A - Sample CRC algorithm..................................27

1. Introduction and terminology

   RFC 3095 [1] defines the RObust Header Compression (ROHC) framework
   and profiles for IP, UDP, RTP, and ESP. During implementation and
   interoperability testing of RFC 3095 some ambiguities and common
   misinterpretations have been identified, as well as a few errors.

   This document summarizes identified issues and provides corrections
   needed for implementations of RFC 3095 to interoperate, i.e. it
   constitutes an update to RFC 3095. This document also provides other
   clarifications related to common misinterpretations of the
   specification. When referring to RFC 3095, this document should
   therefore also be referenced.

   In addition, some clarifications and corrections are also provided
   for RFC 3241 [2] (ROHC over PPP), RFC 3843 [4] (ROHC IP-only
   profile), and RFC 4019 [5] (ROHC UDP-Lite profiles), which are thus
   also updated by this document. Furthermore, RFC 4362 [7] (ROHC Link-
   Layer Assisted Profile) is implicitly updated by this document, since
   also RFC 4362 is based on RFC 3095.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [6].

   When a section of this document makes formal corrections, additions
   or invalidations to text in RFC 3095, this is clearly summarized. The
   text from RFC 3095 that is being addressed is given and labeled
   "INCOMPLETE", "INCORRECT" or "INCORRECT AND INVALIDATED", followed by
   the correct text labeled "CORRECTED", where applicable. When a formal
   addition is provided, it is given with the label "FORMAL ADDITION".

   In this document, a reference to a section or a chapter that is made
   without an explicit mention of a specific document refers to a
   section or a chapter in RFC 3095 [1], unless stated otherwise.



Jonsson, et al.                                                 [Page 3]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


2. CRC calculation and coverage

2.1. CRC calculation

   Section 5.9 defines polynomials for 3, 7 and 8-bit CRCs, but it does
   not specify what algorithm is used. The 3, 7 and 8-bit CRCs are
   calculated using the CRC algorithm defined in [3].

   A PERL implementation of the algorithm can be found in Appendix A of
   this document.

2.2. Padding octet and CRC calculations

   Section 5.9.1 is incomplete, as it does not mention how to handle the
   padding octet in CRC calculations for IR and IR-DYN packets. Padding
   isn't meant to be a meaningful part of a packet and is not included
   in the CRC calculation. As a result, the CRC does not cover the Add-
   CID octet for CID 0, either.

   INCOMPLETE RFC 3095 TEXT (section 5.9.1):

      "The CRC in the IR and IR-DYN packet is calculated over the entire
       IR or IR-DYN packet, excluding Payload and including CID or any
       Add-CID octet."

   CORRECTED TEXT:

      "The CRC in the IR and IR-DYN packet is calculated over the entire
       IR or IR-DYN packet, excluding Payload, Padding and including CID
       or any Add-CID octet, except for the add-CID octet for CID 0."

2.3. CRC coverage in CRC feedback options

   Section 5.7.6.3 is incomplete, as it does not mention how the "size"
   field is handled when calculating the 8-bit CRC used in the CRC
   feedback option. Since the "size" field can be considered an
   extension of the "code" field, it must be treated as the "code"
   field.

   INCOMPLETE RFC 3095 TEXT (section 5.7.6.3):

      "The CRC option contains an 8-bit CRC computed over the entire
       feedback payload, without the packet type and code octet, but
       including any CID fields, using the polynomial of section 5.9.1."

   CORRECTED TEXT:

      "The CRC option contains an 8-bit CRC computed over the entire
       feedback payload including any CID fields but excluding the
       packet type, the 'Size' field and the 'Code' octet, using the
       polynomial of section 5.9.1."



Jonsson, et al.                                                 [Page 4]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006



2.4. CRC coverage of the ESP NULL header

   Section 5.8.7 gives the CRC coverage of the ESP NULL header as
   "Entire ESP header". This must be interpreted as including only the
   initial part of the header (i.e. SPI and Sequence number), and not
   the trailer part at the end of the payload. Therefore, the ESP NULL
   header has the same CRC coverage as the ESP header used in the ESP
   profile (section 5.7.7.7).

3. Mode transition

3.1. Feedback during mode transition to U- and O-mode

   Section 5.6.1 states that during mode transitions, while the D_TRANS
   parameter is I, the decompressor send feedback for each received
   packet. This restrictive behavior prevents a decompressor from using
   a sparse feedback algorithm during mode transitions.

   To reduce transmission overhead and computational complexity
   (including CRC calculation) associated with feedback packets sent for
   each decompressed packet during mode transition, a decompressor MAY
   be implemented with slightly modified mode transition procedures
   compared to those defined in [1], as described in this section.

   These enhanced procedures should be considered only as a possible
   improvement to a decompressor implementation, since interoperability
   is not affected in any way. A decompressor implemented according to
   the optimized procedures will interoperate with an RFC3095
   compressor, as well as a decompressor implemented according to the
   procedures described in RFC3095 does.

3.1.1. Mode transition procedures allowing sparse feedback

   The purpose of these enhanced transition procedures is to allow the
   decompressor to sparsely send feedback for packets decompressed
   during the second half of the transition procedure, i.e. after an
   appropriate IR/IR-DYN/UOR-2 packet has been received from the
   compressor. This is achieved by allowing the decompressor transition
   parameter (D_TRANS) to be set to P (Pending) at that stage, as shown
   in the transition diagrams of sections 3.1.2 and 3.1.3 below.

   This enhanced transition, where feedback need not be sent for every
   decompressed packet, does however introduce some considerations in
   case feedback messages would be lost. Specifically, there is a risk
   for a deadlock situation when a transition from R-mode is performed
   in case no feedback message successfully reaches the compressor and
   the transition is not complete. For transition between U-mode and O-
   mode, there is also a small risk for reduced compression efficiency.





Jonsson, et al.                                                 [Page 5]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


   To avoid this, the decompressor MUST continue to send feedback at
   least periodically, also when in Pending transition state. This is
   equivalent to enhancing the definition of the D_TRANS parameter in
   section 5.6.1, to include the definition of a Pending state:

   - D_TRANS:
      Possible values for the D_TRANS parameter are (I)NITIATED,
      (P)ENDING and (D)ONE. D_TRANS MUST be initialized to D, and a mode
      transition can be initiated only when D_TRANS is D. While D_TRANS
      is I, the decompressor sends a NACK or ACK carrying a CRC option
      for each packet received. When D_TRANS is set to P, the
      decompressor do not have to send a NACK or ACK for each packet
      received, but it MUST continue to send feedback with some
      periodicity, and all feedback packets sent MUST include the CRC
      option. This ensures that all mode transitions will be completed
      also in case of feedback losses.

   These modifications affect transitions to Optimistic and
   Unidirectional modes of operation, i.e. the transitions described in
   sections 5.6.5 and 5.6.6, and make those transition diagrams more
   consistent with the diagram describing the transition to R-mode.

3.1.2. Transition from Reliable to Optimistic mode

   The enhanced procedure for transition from Reliable to Optimistic
   mode is shown below:

            Compressor                     Decompressor
           ----------------------------------------------
                 |                               |
                 |        ACK(O)/NACK(O) +-<-<-<-| D_TRANS = I
                 |       +-<-<-<-<-<-<-<-+       |
     C_TRANS = P |-<-<-<-+                       |
     C_MODE = O  |                               |
                 |->->->-+ IR/IR-DYN/UOR-2(SN,O) |
                 |       +->->->->->->->-+       |
                 |->-..                  +->->->-| D_TRANS = P
                 |->-..                          | D_MODE = O
                 |           ACK(SN,O)   +-<-<-<-|
                 |       +-<-<-<-<-<-<-<-+       |
     C_TRANS = D |-<-<-<-+                       |
                 |                               |
                 |->->->-+  UO-0, UO-1*          |
                 |       +->->->->->->->-+       |
                 |                       +->->->-| D_TRANS = D
                 |                               |








Jonsson, et al.                                                 [Page 6]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


3.1.3. Transition to Unidirectional mode

   The enhanced procedure for transition to Unidirectional mode is shown
   on the following figure:

                Compressor                     Decompressor
               ----------------------------------------------
                 |                               |
                 |        ACK(U)/NACK(U) +-<-<-<-| D_TRANS = I
                 |       +-<-<-<-<-<-<-<-+       |
     C_TRANS = P |-<-<-<-+                       |
     C_MODE = U  |                               |
                 |->->->-+ IR/IR-DYN/UOR-2(SN,U) |
                 |       +->->->->->->->-+       |
                 |->-..                  +->->->-| D_TRANS = P
                 |->-..                          |
                 |           ACK(SN,U)   +-<-<-<-|
                 |       +-<-<-<-<-<-<-<-+       |
     C_TRANS = D |-<-<-<-+                       |
                 |                               |
                 |->->->-+  UO-0, UO-1*          |
                 |       +->->->->->->->-+       |
                 |                       +->->->-| D_TRANS = D
                 |                               | D_MODE= U

3.2. Feedback during mode transition

   Section 5.6.1 states that feedback is always used during mode
   transitions. However, the text then continues by making concrete
   applications of the rule in an inconsistent way, making it unclear
   when CRC's are used. Further, the text does not define how the
   compressor should act during mode transitions based on feedback not
   protected by CRCs, i.e. whether to carry out mode transition actions
   or not. The proper behavior from the compressor is to perform any
   action related to mode transitions only when the feedback is
   protected by the CRC option.

   INCOMPLETE RFC 3095 TEXT (section 5.6.1):

      "As a safeguard against residual errors, all feedback sent during
       a mode transition MUST be protected by a CRC, i.e., the CRC
       option MUST be used."

   CORRECTED TEXT:

      "As a safeguard against residual errors, all feedback sent by the
       decompressor during a mode transition MUST be protected by a CRC,
       i.e., the CRC option MUST be used. The compressor MUST ignore
       feedback information related to mode transition if the feedback
       is not protected by the CRC option."




Jonsson, et al.                                                 [Page 7]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


   One more related issue that requires clarifications comes from the
   following text at the end of section 5.6.1:

      "While D_TRANS is I, the decompressor sends a NACK or ACK carrying
       a CRC option for each received packet."

   However, Section 5.5.2.2 already stated that for R-mode, feedback is
   never sent for packets that do not update the context, i.e. for
   packets that do not carry a CRC such as R-0 and R-1* packets.

   This means that when D_TRANS=I during mode transition, a decompressor
   operating in R-mode sends an acknowledgement for each packet it
   receives and MUST use the sequence number that corresponds to the
   packet that last updated the context, i.e. the decompressor MUST NOT
   use the sequence number of the R-0 or the R-1* packet."

3.3. Packet decoding during mode transition

   Each ROHC profile defines its own set of packet formats, and also its
   own feedback packets. The use of various operational modes is also
   defined by each specific profile. A decompressor can therefore not
   initiate a mode transition request before at least one packet of a
   new context has been correctly decompressed, establishing the context
   based on one specific profile (as specified in IR packets). The
   context must be established before the decompressor can know the
   profile used, which modes are defined by that profile, and the
   feedback packet formats available. Mode transition can therefore not
   be initiated by the decompressor before it has an established context
   for the CID.

   If the original transition procedures in sections 5.6.5 and 5.6.6 are
   followed (and not the enhanced procedures described in section 3.1 of
   this document), it is important to note that type 0 or type 1 packets
   may be received by the decompressor during the first half of the
   transition procedure, and these packets must not be mistakenly
   interpreted as the packets sent by the compressor to indicate
   completed transition. The decompressor side MUST therefore keep track
   of the transition status, e.g. with an additional parameter. If the
   enhanced transition procedures described in section 3 of this
   document are used, the D_TRANS parameter can serve this purpose since
   its definition and usage is slightly modified.

4. Timestamp encoding

4.1. Encoding used for compressed TS bits

   RTP Timestamp values (TS) are always encoded using W-LSB encoding,
   both when sent scaled and when sent unscaled. For TS values sent in
   Extension 3, W-LSB encoded values are sent using the self-describing
   variable-length format (section 4.5.6), and this applies to both
   scaled and unscaled values.



Jonsson, et al.                                                 [Page 8]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


4.2. (De)compression of TS without transmitted TS bits

   When ROHC RTP operate using its most efficient packet types, apart
   from packet type identification and the error detection CRC, only RTP
   sequence number (SN) bits have to be transmitted in RTP compressed
   headers. All other fields are then omitted either because they are
   unchanged or because they can be reconstructed through a function
   from the SN (i.e. by combining the transmitted SN bits with state
   information from the context). Fields that can be inferred from the
   SN are the IP Identification (IP-ID) and the RTP Timestamp (TS).

   IP-ID compression and decompression, both with and without
   transmitted IP-ID bits in the compressed header, are well defined in
   section 4.5.5 (see section 8.2 of this document). However, for TS it
   is only defined how to decompress based on actual TS bits in the
   compressed header, either scaled or unscaled, but not how to infer
   the TS from the SN, i.e. in SO-state operation. This section
   specifies how the TS (scaled or unscaled) is decompressed when no TS
   bits are transmitted in the compressed header.

   When no TS bits are transmitted in the compressed header, the encoded
   TS value (scaled or unscaled) is decompressed assuming a linear
   extrapolation from the SN, i.e. delta_TS = delta_SN * default-slope,
   where delta_SN and delta_TS are both signed integers. Section 5.7
   defines the potential values for default-slope.

   INCOMPLETE RFC 3095 TEXT (section 5.7):

      "If value(Tsc) = 1, Scaled RTP Timestamp encoding is used before
       compression (see section 4.5.3), and default-slope(TS) = 1.

       If value(Tsc) = 0, the Timestamp value is compressed as-is, and
       default-slope(TS) = value(TS_STRIDE)."

   CORRECTED TEXT:

      "When a compressed header with no TS bits is received, the encoded
       TS value (scaled or unscaled) is decompressed assuming a linear
       extrapolation from the SN, i.e. delta_TS = delta_SN * default-
       slope.

       If value(Tsc) = 1, Scaled RTP Timestamp encoding is used before
       compression (see section 4.5.3), and default-slope(TS) = 1.

       If value(Tsc) = 0, the Timestamp value is compressed as-is, and
       default-slope(TS) = value(TS_STRIDE)."

   INCORRECT AND INVALIDATED RFC 3095 TEXT (section 5.5.1.2):

      "For example, in a typical case where the string pattern has the
       form of non-SN-field = SN * slope + offset, one ACK is enough if



Jonsson, et al.                                                 [Page 9]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


       the slope has been previously established by the decompressor
       (i.e., only the new offset needs to be synchronized). Otherwise,
       two ACKs are required since the decompressor needs two headers to
       learn both the new slope and the new offset."

   Consequently, there is no other slope value than the default-slope,
   as defined in section 5.7.

4.3. Interpretation intervals for TS encoding

   Section 4.5.4 defines the interpretation interval, p, for timer-based
   compression of the RTP timestamp.  However, Section 5.7 defines a
   different interpretation interval, which is defined as the
   interpretation interval to use for all TS values.  It is thus unclear
   which p-value to use, at least for timer-based compression.

   The way this should be interpreted is that the p-value differs
   depending on whether timer-based compression is enabled or not.

   For timer-based compression (TIME_STRIDE set to a non-zero value),
   the interpretation interval is:
      p = 2^(k-1) - 1 (as per section 4.5.4)
   Otherwise, the interpretation interval is:
      p = 2^(k-2) - 1 (as per section 5.7)

   Since two different p-values are used, the compressor must take this
   into account throughout the process of enabling timer-based
   compression (see section 4.8 of this document). During transition
   from window-based compression to timer-based compression, it is thus
   necessary that the compressor keep k large enough to cover both
   interpretation intervals.

4.4. TS_STRIDE for scaled timestamp encoding

   RFC 3095 defines the timestamp stride (TS_STRIDE) as the expected
   increase in the timestamp value between two RTP packets with
   consecutive sequence numbers. TS_STRIDE is set by the compressor and
   explicitly communicated to the decompressor, and it is used either as
   the scaling factor for scaled TS encoding, or constitutes the
   default-slope used when decompressing an unscaled TS through a linear
   extrapolation from the SN (see also section 4.2 of this document).

   The relation between TS and TS_SCALED, given by the following
   equality in section 4.5.3, defines the mathematical meaning of
   TS_STRIDE:

      TS = TS_SCALED * TS_STRIDE + TS_OFFSET

   TS_SCALED is incorrectly written as TS / TS_STRIDE in the compression
   step following the above core equality. This formula is incorrect
   both because it excludes TS_OFFSET and because it would prevent a



Jonsson, et al.                                                [Page 10]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


   TS_STRIDE value of 0, which is an alternative not excluded by the
   core equality above. If "/" were a generally unambiguously defined
   operation meaning "the integral part of the result from dividing X by
   Y", the absence of TS_OFFSET could be explained, but the formula
   would still lack a proper output for TS_STRIDE equal to 0. The
   formula of "2. Compression" is thus invalid.

   INCORRECT RFC 3095 TEXT (section 4.5.3):

      "2. Compression: After initialization, the compressor no longer
          compresses the original TS values. Instead, it compresses the
          downscaled values: TS_SCALED = TS / TS_STRIDE. The
          compression method could be either W-LSB encoding or the
          timer-based encoding described in the next section."

   CORRECTED TEXT:

      "2. Compression: After initialization, the compressor no longer
          compresses the original TS values. Instead, it compresses the
          downscaled values. The compression method could be either
          W-LSB encoding or the timer-based encoding described in the
          next section."

4.5. TS wraparound with scaled timestamp encoding

   Section 4.5.3 states in point 4 and 5 that the compressor is not
   required to initialize TS_OFFSET at wraparound, but that it is
   required to increase the number of bits sent for the scaled TS value
   when there is a TS wraparound. The decompressor is also required to
   detect and cope with TS wraparound, including updating TS_OFFSET.

   This method is not interoperable and not robust. The gain is also
   insignificant, as TS wraparound happens very seldom. Therefore, the
   compressor reinitializes TS_OFFSET upon TS wraparound, by sending
   unscaled TS.

   INCORRECT RFC 3095 TEXT (section 4.5.3):

      "4. Offset at wraparound: Wraparound of the unscaled 32-bit TS
          will invalidate the current value of TS_OFFSET used in the
          equation above. For example, let us assume TS_STRIDE = 160 =
          0xA0 and the current TS = 0xFFFFFFF0. TS_OFFSET is then 0x50
          = 80.  Then if the next RTP TS = 0x00000130 (i.e., the
          increment is 160 * 2 = 320), the new TS_OFFSET should be
          0x00000130 modulo 0xA0 = 0x90 = 144.  The compressor is not
          required to re-initialize TS_OFFSET at wraparound. Instead,
          the decompressor MUST detect wraparound of the unscaled TS
          (which is trivial) and update TS_OFFSET to

          TS_OFFSET = (Wrapped around unscaled TS) modulo TS_STRIDE




Jonsson, et al.                                                [Page 11]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


   CORRECTED TEXT:

      "4. Offset at wraparound: If the value of TS_STRIDE is not equal
          to a power of two, wraparound of the unscaled 32-bit TS will
          change the value of TS_OFFSET. When this happens, the
          compressor SHOULD reinitialize TS_OFFSET by sending unscaled
          TS, as in 1 above."

   INCORRECT AND INVALIDATED RFC 3095 TEXT (section 4.5.3):

      The entire point 5, i.e. the entire text starting from "5.
      Interpretation interval at wraparound ...", down to and including
      the block of text that starts with "Let a be the number of LSBs"
      and that ends with "...interpretation interval is b." is incorrect
      and is thus invalid.

4.6. Recalculating TS_OFFSET

   TS can be sent unscaled if the TS value change does not match the
   established TS_STRIDE, but the TS_STRIDE might still stay unchanged.
   To ensure correct decompression of subsequent packets, the
   decompressor MUST therefore always recalculate TS_OFFSET (RTP TS
   modulo TS_STRIDE) when a packet with an unscaled TS value is
   received.

4.7. TS_STRIDE and the Tsc flag in Extension 3

   The Tsc flag in Extension 3 indicates whether TS is scaled or not.
   The value of the Tsc flag thus applies to all TS bits, also if there
   are no TS bits in the extension itself. When TS is scaled, it is
   always scaled using context(TS_STRIDE). The legend for Extension 3 in
   section 5.7.5 incorrectly states that value(TS_STRIDE) is used for
   scaled TS, which is incorrect.

   If TS_STRIDE is present in Extension 3, as indicated by the Tss flag
   being set, the TS field in the compressed header SHOULD contain
   unscaled TS bits, i.e. the Tsc flag SHOULD NOT be set when Tss is set
   since an unscaled TS is needed together with TS_STRIDE to recalculate
   the TS_OFFSET. If TS_STRIDE is included in a compressed header with
   scaled TS, the decompressor must ignore and discard field(TS_STRIDE).

   INCORRECT RFC 3095 TEXT (section 4.5.3):

      "Tsc: Tsc = 0 indicates that TS is not scaled;
            Tsc = 1 indicates that TS is scaled according to section
             4.5.3, using value(TS_STRIDE).
             Context(Tsc) is always 1.  If scaling is not desired, the
             compressor will establish TS_STRIDE = 1."






Jonsson, et al.                                                [Page 12]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


   CORRECTED TEXT:

      "Tsc: Tsc = 0 indicates that TS is not scaled;
            Tsc = 1 indicates that TS is scaled according to section
            4.5.3, using context(TS_STRIDE).

            Context(Tsc) is always 1.  If scaling is not desired, the
            compressor will establish TS_STRIDE = 1.

            If field(Tsc) = 1, and if TSS = 1 (meaning that TS_STRIDE is
            present in the extension), field(TS_STRIDE) MUST be ignored
            and discarded."

   When the compressor re-establishes a new value for TS_STRIDE using
   Extension-3, it should send unscaled TS bits together with TS_STRIDE.

4.8. Using timer-based compression

   Timer-based compression of the RTP timestamp, as described in section
   4.5.4, may be used to reduce the number of transmitted timestamp bits
   (bytes) needed when the timestamp can not be inferred from the SN.
   Timer-based compression is only used for decompression of compressed
   headers that contains a TS field, otherwise when no timestamp bits
   are present the timestamp is linearly inferred from the SN (see
   section 4.2 of this document).

   Whether to use timer-based compression or not is controlled by the
   TIME_STRIDE control field, which can be set either by an IR, an IR-
   DYN, or by a compressed packet with extension 3. Before timer-based
   compression can be used, the decompressor has to inform the
   compressor (on a per-channel basis) about its clock resolution by
   sending a CLOCK feedback option for any CID on the channel. The
   compressor can then initiate timer-based compression by sending (on a
   per-context basis) a non-zero TIME_STRIDE to the decompressor. First
   when the compressor is confident that the decompressor has received
   the TIME_STRIDE value, it can switch to timer-based compression.

5. List compression

5.1. CSRC list items in RTP dynamic chain

   Section 5.7.7.6 defines the static and dynamic parts of the RTP
   header. This section indicates a 'Generic CSRC list' field in the
   dynamic chain, which has a variable length (see section 5.8.6). This
   field is always at least one octet in size, even if the list is empty
   (as opposed to the CSRC list in the uncompressed RTP header, which is
   not present when the RTP CC field is set to 0).







Jonsson, et al.                                                [Page 13]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


5.2. Multiple occurrences of the CC field

   The static and the dynamic parts of the RTP header are defined in
   Section 5.7.7.6. In the dynamic part, a CC field indicates the number
   of CSRC items present in the 'Generic CSRC list'. Another CC field
   also appears within the 'Generic CSRC list' (section 5.8.6.1),
   because Encoding Type 0 is always used in the dynamic chain. Both CC
   fields have the same meaning: the value of the CC field determines
   the number of XI items in the CSRC list for Encoding Type 0, and it
   is not used otherwise. Therefore, the following applies:

   FORMAL ADDITION TO RFC 3095:

      "The first octet in the dynamic part of the RTP header contains a
       CC field, as defined in section 5.7.7.6. A second occurrence
       appears in the 'Generic CSRC list', which is also in the dynamic
       part of the RTP header, where Encoding Type 0 is used according
       to the format defined in 5.8.6.1.

       The compressor MUST set both occurrences of the CC field to the
       same value.

       The decompressor MUST use the value of the CC field from the
       Encoding Type 0 within the Generic CRSC list, and it MUST thus
       ignore the first occurrence of the CC field."

5.3. Bit masks in list compression

   The insertion and/or removal schemes, described in sections 5.8.6.2 -
   5.8.6.4, use bit masks to indicates insertion or removal positions
   within the reference list. The size of the bit mask can be 7-bit or
   15-bit.

   The compressor MAY use a 7-bit mask, even if the reference list has
   more than 7 items, provided that changes to the list are only applied
   to items within the first 7 items of the reference list, leaving
   items with an index not covered by the 7-bit mask unchanged.

   The decompressor MUST NOT modify items with an index not covered by
   the 7-bit mask, when a 7-bit mask is received for a reference list
   that contains more than 7 items.

5.4. Headers compressed with list compression

   In section 5.8, it is stated that headers which can be part of
   extension header chains "include" AH, null ESP, minimal encapsulation
   (MINE), GRE, and IPv6 extensions. This list of headers which can be
   compressed is correct, but the word "include" should not be there,
   since only the header types listed can actually be handled. It should
   further be noted that for the Minimal Encapsulation (MINE) header,




Jonsson, et al.                                                [Page 14]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


   there is no explicit discussion of how to compress it, as the header
   is either sent uncompressed or fully compressed away.

5.5. ESP NULL header list compression

   Due to the offset of the fields in the trailer part of the ESP
   header, a compressor MUST NOT compress packets containing more than
   one NULL ESP header, unless the second-outermost header is treated as
   a regular ESP header and the packets are compressed using profile
   0x0003.

5.6. Translation tables and indexes for IP extension headers

   Section 5.8.4 describes how list indexes are associated to list items
   and how table lists are built for IP extension headers. The text
   incorrectly states that one index per type is used, since the same
   type can appear several times with different content in one single
   chain.

   In IP extension header list compression, an index is associated with
   each individual extension header of an extension header chain. When
   there are multiple non-identical occurrences of the same extension
   type (Protocol Number) within a header chain, each MUST be given its
   own index.

   In the case where there are multiple identical occurrences of the
   same extension type, the compressor can associate them to the same
   index. When the value of an item whose index occurs more than once in
   the list is updated, the compressor MUST send the value for each
   occurrence of that index in the list.

   When content of extension headers changes, an implementation can
   choose to either use a different index, or update the existing one.
   Some extensions can be compressed away also when some fields change,
   as those changes can be conveyed to the decompressor implicitly (e.g.
   sequence numbers in extension headers that can be inferred from the
   RTP SN) or explicitly (e.g. as part of the 'IP extension header(s)'
   field in extension 3).

   When there is more than one IP header, there is more than one list of
   extension headers, and a translation table is maintained for each
   list independently of one another.

5.7. Reference list

   A list compressed using encoding type 1 (insertion), type 2 (removal)
   or type 3 (removal/insertion) uses a coding scheme that is based on
   the use of a reference list in the context (identified as ref_id).

   While it could seem a fair choice to send a type 1 list when ref_id
   is an empty list, there is no gain in doing so with respect to using



Jonsson, et al.                                                [Page 15]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


   a type 0 list. Sending a type 2 list when ref_id is an empty list
   would lead to a failure, while sending a type 3 list has very little
   meaning. All these alternatives could be seen as possible, based on
   how list compression is specified in RFC 3095.

   If these alternatives were allowed, a decompressor would become
   required to maintain a sliding window of ref_id lists in R-mode, even
   for the case where no items are sent in the compressed list, and this
   is not a desirable requirement. Using list encoding type 1, type 2,
   and type 3 is therefore only allowed for non-empty reference lists.

   FORMAL ADDITION TO RFC 3095:

      "Regardless of the operating mode, for list encoding of type 1,
       type 2, and type 3 lists, ref_id MUST refer to a non-empty list."

5.8. Compression of AH and GRE sequence numbers

   Section 5.8.4.2 and section 5.8.4.4 describes how to compress the
   Authentication Header (AH) and the Generic Routing Encapsulation
   (GRE) header. Both these sections present a possibility to omit the
   AH/GRE sequence number in the compressed header, under certain
   circumstances. However, the specific conditions for omitting the
   AH/GRE sequence number, as well as the concrete compression and
   decompression procedures to apply, are not clearly defined to
   guarantee robustness and facilitate interoperable implementation.

   Proper rules are provided for the ESP case, i.e.:

      "Sequence Number: Not sent when the offset from the sequence
       number of the compressed header is constant, when the compressor
       has confidence that the decompressor has established the correct
       offset. When the offset is not constant, the sequence number may
       be compressed by sending LSBs"

   The same logic applies to the AH/GRE sequence numbers.

   INCORRECT RFC 3095 TEXT (section 5.8.4.2):

      "If the sequence number in the AH linearly increases as the RTP
       Sequence Number increases, and the compressor is confident that
       the decompressor has obtained the pattern, the sequence number in
       AH need not be sent. The decompressor applies linear
       extrapolation to reconstruct the sequence number in the AH."

   CORRECTED TEXT:

      "The AH sequence number can be omitted from the compressed header
       when the offset from the sequence number (SN) of the compressed
       header is constant, when the compressor has confidence that
       the decompressor has established the correct offset."



Jonsson, et al.                                                [Page 16]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006



   INCORRECT RFC 3095 TEXT (section 5.8.4.4):

      "If the sequence number in the GRE header linearly increases as
       the RTP Sequence Number increases and the compressor is confident
       that the decompressor has received the pattern, the sequence
       number in GRE need not be sent. The decompressor applies linear
       extrapolation to reconstruct the sequence number in the GRE
       header."

   CORRECTED TEXT:

      "The GRE sequence number can be omitted from the compressed header
       when the offset from the sequence number (SN) of the compressed
       header is constant, when the compressor has confidence that the
       decompressor has established the correct offset."

6. Updating properties

6.1. Implicit updates

   A context updating packet that contains compressed sequence number
   information may also carry information about other fields; in such
   case, these fields are updated according to the content of the
   packet. The updating packet also implicitly updates inferred fields
   (e.g. RTP timestamp) according to the current mode and the
   appropriate mapping function of the updated and the inferred fields.

   An updating packet thus updates the reference values of all header
   fields, either explicitly or implicitly, with an exception for the
   UO-1-ID packet (see section 6.2 of this document). In UO-mode, all
   packets are updating packets, while in R-mode all packets with a CRC
   are updating packets.

   For example, a UO-0 packet contains the compressed RTP sequence
   number (SN). Such a packet also implicitly updates RTP timestamp,
   IPv4 ID, and sequence numbers of IP extension headers.

6.2. Updating properties of UO-1*

   Section 5.7.3 states that the values provided in extensions carried
   by a UO-1-ID packet do not update the context, except for SN, TS, or
   IP-ID fields. However, section 5.8.1 correctly states that the
   translation table in the context is updated whenever an (Index, item)
   pair is received, something that is contradicted by the statement in
   5.7.3 because the UO-1-ID packet can carry extension 3 with (Index,
   item) pair items within the 'Compressed CSRC list' field. In addition
   to this contradiction, the text does not mention what to do with the
   other sequence numbers inferred from the SN, which are also to be
   implicitly updated. The updating properties of UO-1* as stated by
   section 5.7.3 are thus incomplete.



Jonsson, et al.                                                [Page 17]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006



   INCOMPLETE RFC 3095 TEXT (section 5.7.3):

      "Values provided in extensions, except those in other SN, TS,
       or IP-ID fields, do not update the context."

   CORRECTED TEXT:

      "UO-1-ID packets only updates TS, SN, IP-ID, and sequence
       numbers of IP extension headers. Other values
       provided in extensions do not update the context.

       The decompressor MUST update its translation table whenever an
       (Index, item) pair is received, as per Section 5.8.1, and this
       rule applies also to UO-1-ID packets."

6.3. Context updating properties for IR packets

   IR packets do not clear the whole context, but update all fields
   carried in the IR header. Similarly, an IR without a dynamic chain
   simply updates the static part of the context, while the rest of the
   context is left unchanged.

   A consequence of this is that fields that are not updated by the IR
   packet, e.g. the translation tables for list compression, MUST NOT be
   invalidated by the decompressor when it assumes context damage.

6.4. RTP padding field (R-P) in extension 3

   Section 5.7.5 defines the properties of RTP header flags and fields
   in extension 3. These get updated when the rtp flag of the extension
   3 is set, i.e. when rtp = 1, otherwise they are not updated. However,
   it is unclear how extension 3 updates the R-P bit in the context.

   INCOMPLETE RFC 3095 TEXT (section 5.7.5):

      "R-P: RTP Padding bit, absolute value (presumed zero if absent)."

   CORRECTED TEXT:

      "R-P: RTP Padding bit. If R-PT = 1, R-P is the absolute value of
            the RTP padding bit and this value updates context(R-P). If
            R-PT = 0, context(R-P) is updated to zero."

6.5. RTP eXtension bit (X) in dynamic part

   Section 5.7.7.6 defines the properties of the RTP header flags and
   fields in the RTP part of the dynamic chain of IR and IR-DYN packets.
   However, it is unclear how the X bit is updated in the context.





Jonsson, et al.                                                [Page 18]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


   INCOMPLETE RFC 3095 TEXT (section 5.7.7.6):

      "X: Copy of X bit from RTP header (presumed 0 if RX = 0)"

   CORRECTED TEXT:

      "X: X bit from RTP header. If RX = 1, X is the X bit from the RTP
          header and this value updates context(X). If RX = 0,
          context(X) is updated to zero."

7. Context management and CID/context re-use

7.1. Persistence of decompressor contexts

   As part of the negotiated channel parameters, compressor and
   decompressor have through the MAX_CID parameter agreed on the highest
   context identification (CID) number to be used. By agreeing on
   MAX_CID, the decompressor also agrees to provide memory resources to
   host at least MAX_CID+1 contexts, and an established context with a
   CID within this negotiated space MUST be kept by the decompressor
   until either the CID gets re-used, or the channel is taken down or
   re-negotiated.

7.2. CID/context re-use

   As part of the channel negotiation, the maximal number of active
   contexts supported is negotiated between the compressor and the
   decompressor through the MAX_CID parameter. The value of MAX_CID can
   differ significantly from one link application to another, as well as
   the load in terms of the number of packet streams to compress. The
   lifetime of a ROHC channel can also vary, from almost permanent to
   rather short-lived. However, in general it is not expected that
   resources will be allocated for more contexts than what can
   reasonably be expected to be active concurrently over the link. As a
   consequence hereof, context identifiers (CIDs) and context memory are
   resources that will have to be re-used by the compressor as part of
   what can be considered normal operation.

   How context resources are re-used is in RFC 3095 [1] and subsequent
   ROHC standards left unspecified and up to implementation. This
   document does not intends to change that, i.e. ROHC resource
   management is still considered an implementation detail. However, re-
   using a CID and its allocated memory is not always as simple as
   initiating a context with a previously unused CID. Because some
   profiles can be operating in various modes where packet formats vary
   depending on current mode, care has to be taken to ensure that the
   old context data will be completely and safely overwritten,
   eliminating the risk of undesired side effects from interactions
   between old and new context data. This document therefore points out
   some important core aspects to consider when implementing resource
   management in ROHC compressors and decompressors.



Jonsson, et al.                                                [Page 19]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006



   On a high level, CID/context re-use can be of two kinds, either re-
   use for a new context based on the same profile as the old context,
   or for a new context based on a different profile. These cases, are
   discussed separately in the following two subsections.

7.2.1. Re-using a CID/context with the same profile

   For multi-mode profiles, such as those defined in RFC 3095 [1], mode
   transitions are performed using a decompressor-initiated handshake
   procedure, as defined in section 5.6. When a CID/context is re-used
   for a new context based on the same profile as the old context, the
   current mode of operation SHOULD be inherited from the old to the new
   context. Specifically, the compressor SHOULD continue to operate
   using the mode of operation of the old context also with the new
   context. The reason for this is that there is no reliable way for the
   compressor to inform the decompressor that a CID/context re-use is
   happening. The decompressor can thus not be expected to clear the
   context memory for the CID (see section 6.3 of this document), and
   there is no way to trigger a safe mode switching (which requires the
   decompressor-initiated handshake procedure).

   The rule of mode inheritance applies also when the
   CONTEXT_REINITIALIZATION signal (section 6.3.1) is used to reinitiate
   an entire context.

7.2.2. Re-using a CID/context with a different profile

   When a CID is re-used for a new context based on a different profile
   than the old context, both the compressor and the decompressor MUST
   start operation with that context in the initial mode of the profile
   (if it is a multi-mode profile). This applies both to IR-initiated
   new contexts and profile downgrades with IR-DYN (e.g. the profile
   0x0001 -> profile 0x0002 downgrade in [1], section 5.11.1).

   Type 0 and type 1 packets have different formats in U/O- and R-mode,
   and these R-mode packets have no CRC. When initiating a new context
   on a re-used R-mode CID, there is a risk that the decompressor will
   misinterpret compressed packets, if the initiating IR packets are
   lost.

   A CID for a context currently operating in R-mode SHOULD therefore
   not be re-used for a new context based on a different profile than
   the old context. A compressor doing otherwise should minimize the
   risk for misinterpretation of R-0/R-1 by e.g. not using packets of
   types beginning with 00 or 10 before it is highly confident that the
   new context has successfully been initiated at the decompressor.







Jonsson, et al.                                                [Page 20]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


8. Other protocol clarifications

8.1. Meaning of NBO

   In IPv4 dynamic part (Section 5.7.7.4), if the 'NBO' bit is set, it
   means that network byte order is used.

8.2. IP-ID

   According to Section 5.7, IP-ID means the compressed value of the
   IPv4 header's 'Identification' field. Compressed packets contain this
   compressed value (IP-ID), while IR packets with dynamic chain and IR-
   DYN packets transmit the original, uncompressed Identification field
   value. The IP-ID field always represents the Identification value of
   the innermost IPv4 header whose corresponding RND flag is not 1.

   If RND or RND2 is set to 1, the corresponding IP-ID(s) is(are) sent
   as 16-bit uncompressed Identification value(s) at the end of the
   compressed base header, according to the IP-ID description (see the
   beginning of section 5.7). When there is no compressed IP-ID, i.e.
   for IPv6 or when all IP Identification information is sent as-is (as
   indicated by RND/RND2 being set to 1), the decompressor ignores IP-ID
   bits sent within compressed base headers.

   When RND=RND2=0, IP-ID is compressed, i.e. expressed as an SN offset
   and byte-swapped if NBO=0. This is the case also when 16 bits of IP-
   ID is sent in extension 3.

   When RND=0 but no IP-ID bits are sent in the compressed header, the
   SN offset for IP-ID stays unchanged, meaning that Offset_m equals
   Offset_ref, as described in Section 4.5.5. This is further expressed
   in a slightly different way (with the same meaning) in Section 5.7,
   where it is said that "default-slope(IP-ID offset) = 0", meaning that
   if no bits are sent for IP-ID, its SN offset slope defaults to 0.

8.3. Extension-3 in UOR-2* packets

   Some flags of the IP header in the extension (e.g. NBO or RND) may
   change the interpretation of fields in UOR-2* packets. In such cases,
   when a flag changes in Extension-3, a decompressor MUST re-parse the
   UOR-2* packet.

8.4. Multiple occurrences of the M bit

   The RTP header part of Extension 3, as defined by section 5.7.5,
   includes a one-bit field for the RTP Marker bit. This field is also
   present in all compressed base header formats except for UO-1-ID,
   meaning there may be multiple occurrences of the field within one
   single compressed header. In such cases, the two M fields must have
   the same value.




Jonsson, et al.                                                [Page 21]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


   FORMAL ADDITION TO RFC 3095:

      "When there are two occurrences of the M field in a compressed
       header (both in the compressed base header and in the RTP part of
       Extension 3), the compressor MUST set both these occurrences of
       the M field to the same value.

       At the decompressor, if the two M field values of such a packet
       are not identical, the packet MUST be discarded."

8.5. Multiple SN options in one feedback packet

   The length of the sequence number field in the original ESP header is
   32 bits. The format of the SN feedback option (5.7.6.6) allows for 8
   additional SN bits to the 12 SN bits of the FEEDBACK-2 format
   (5.7.6.1). One single SN feedback option is thus not enough for the
   decompressor to send back all the 32 bits of the ESP sequence number
   in a feedback packet, unless it uses multiple SN options in one
   feedback packet.  Section 5.7.6.1 declares that a FEEDABCK-2 packet
   can contain variable number of feedback options and the options can
   appear in any order.

   When processing multiple SN options in one feedback packet, the SN
   would be given by concatenating the fields.

8.6. Multiple CRC options in one feedback packet

   Although it is not useful to have more than one single CRC option in
   a feedback packet, having multiple CRC options is still allowed. If
   multiple CRC options are included, all such CRC options MUST be
   identical, as they will be calculated over the same header, the
   compressor SHOULD otherwise discard the feedback packet.

8.7. Responding to lost feedback links

   Although this is neither desirable or expected, it may happen that a
   link used to carry feedback between two associated instances becomes
   unavailable. If the compressor can be notified of such event, the
   compressor SHOULD restart compression for each flow that is operating
   in R-mode. When restarting compression, the compressor SHOULD use a
   different CID for each flow being restarted; this is useful to avoid
   that packet types for which both U/O-mode and R-mode share the same
   type identifier gets misinterpreted when restarting the flow in U-
   mode (see also section 7.2 of this document).

   Generally, feedback links are not expected to disappear when once
   present, but it should be noted that this might be the case for
   certain link technologies.






Jonsson, et al.                                                [Page 22]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


8.8. UOR-2 in profile 0x0002 (UDP) and profile 0x0003 (ESP)

   One single new format is defined for UOR-2 in profile 0x0002 and
   profile 0x0003, which replaces all three (UOR-2, UOR-2-ID, UOR-2-TS)
   formats from profile 0x0001. The same UOR-2 format is thus used
   independent of whether there are IP headers with a corresponding
   RND=1 or not. This also applies to the IP profile [4] and the IP/UDP-
   Lite profile [5].

8.9. Sequence number LSB's in IP extension headers

   In section 5.8.5, formats are defined for compression of IP extension
   header fields. These include compressed sequence number fields, and
   these fields contain "LSB of sequence number". These sequence numbers
   are not "LSB-encoded" as e.g. the RTP sequence number, but are the
   LSB's of the uncompressed fields.

8.10. Expecting UOR-2 ACKs in O-mode

   Usage of UOR-2 ACKs in O-mode, as discussed in section 5.4.1.1.2, is
   optional. A decompressor can also send ACKs for purposes other than
   to acknowledge the UOR-2, without having to continue sending ACKs for
   all UOR-2. Similarly, a compressor implementation can ignore UOR-2
   ACKs for the purpose of adapting the optimistic approach strategies.

   It is thus RECOMMENDED to not use of the optional ACK mechanism in
   O-mode, neither in compressor nor in decompressor implementations.

   Using an incorrect expectation on UOR-2 ACKs as a basis for
   compressor behavior will significantly degrade the compression
   performance. This is because UOR-2 ACKs can be sent from a
   decompressor for other purposes than to acknowledge the UOR-2 packet,
   e.g. to send feedback such as clock resolution, or to initiate a mode
   transition. If an implementation does use the optional acknowledgment
   algorithm described in Section 5.4.1.1.2, it must make sure to set
   the k_3 and n_3 parameters to much larger values than one to ensure
   that the compressor performance is not degraded due to the problem
   described above.

9. ROHC negotiation

   Section 4.1 states that the link layer must provide means to
   negotiate e.g. the channel parameters listed in section 5.1.1. One of
   these parameters is the PROFILES parameter, which is a set of non-
   negative integers where each integer indicates a profile supported by
   the decompressor.

   Each profile is identified by a 16-bit value, where the 8 LSB bits
   indicate the actual profile, and the 8 MSB bits indicate the variant
   of that profile (see chapter 8). In the ROHC headers sent over the
   link, the profile used is identified only with the 8 LSB bits, which



Jonsson, et al.                                                [Page 23]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


   means that the compressor and decompressor must have agreed on which
   variant to use for each profile.

   The negotiation protocol must thus be able to communicate to the
   compressor the set of profiles supported by the decompressor, and
   when multiple variants of the same profile are available, also
   provide means for the decompressor to know which variant will be used
   by the compressor.  This basically means that the PROFILES set after
   negotiation MUST NOT include more than one variant of a profile.

10. PROFILES suboption in ROHC-over-PPP

   The logical union of suboptions for IPCP and IPV6CP negotiations, as
   specified by ROHC over PPP [2], can not be used for the PROFILES
   suboption, as the whole union would then have to be considered within
   each of the two IPCP negotiations, to avoid getting an ambiguous
   profile set. An implementation of RFC 3241 MUST therefore ensure the
   same profile set is negotiated for both IPv4 and IPv6 (IPCP/IPV6CP).

11. Constant IP-ID encoding in IP-only and UPD-Lite profiles

   In the ROHC IP-only profile, section 3.3 of RFC 3843 [4], a mechanism
   for encoding of a constant Identification value in IPv4 (constant IP-
   ID) is defined. This mechanism is also used by the ROHC UDP-Lite
   profiles, RFC 4019 [5].

   The "Constant IP-ID" mechanism applies to both the inner and the
   outer IP header, when present, meaning that there will be both a SID
   and a SID2 context value.

12. Security considerations

   This document provides a number of corrections and clarifications to
   [1], but it does not make any changes with regards to the security
   aspects of the protocol. As a consequence, the security
   considerations of [1] apply without additions.


13. IANA considerations

   This document does not require any IANA actions.

14. Acknowledgment

   The authors would like to thank Vicknesan Ayadurai, Carsten Bormann,
   Mikael Degermark, Zhigang Liu, Abigail Surtees, Mark West, Tommy
   Lundemo, Alan Kennington and Remi Pelland for their contributions and
   comments. Thanks also to the committed document reviewers, Carl
   Knutsson and Biplab Sarkar, who reviewed the document during working
   group last-call.




Jonsson, et al.                                                [Page 24]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


15. References

15.1. Normative References

   [1]  C. Bormann, et al., "RObust Header Compression (ROHC): Framework
        and four profiles: RTP, UDP, ESP, and uncompressed",
        RFC 3095, July 2001.

   [2]  C. Bormann, "Robust Header Compression (ROHC) over PPP",
        RFC 3241, April 2002.

   [3]  W. Simpson, "PPP in HDLC-like Framing", RFC 1662, July 1994.

   [4]  L-E. Jonsson & G. Pelletier, "RObust Header Compression (ROHC):
        A Compression Profile for IP", RFC 3843, June 2004.

   [5]  G. Pelletier, "RObust Header Compression (ROHC): Profiles for
        User Datagram Protocol (UDP) Lite", RFC 4019, April 2005.

   [6]  S. Bradner, "Key words for use in RFCs to Indicate Requirement
        Levels", BCP 14, RFC 2119, March 1997.

15.2. Informative References

   [7]  L-E. Jonsson, G. Pelletier & K. Sandlund, "RObust Header
        Compression (ROHC): A Link-Layer Assisted Profile for
        IP/UDP/RTP", RFC 4362, June 2004.



























Jonsson, et al.                                                [Page 25]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


16. Authors' Addresses

   Lars-Erik Jonsson
   Ericsson AB
   Box 920
   SE-971 28 Lulea, Sweden
   Phone: +46 8 404 29 61
   EMail: lars-erik.jonsson@ericsson.com

   Kristofer Sandlund
   Ericsson AB
   Box 920
   SE-971 28 Lulea, Sweden
   Phone: +46 8 404 41 58
   EMail: kristofer.sandlund@ericsson.com

   Ghyslain Pelletier
   Ericsson AB
   Box 920
   SE-971 28 Lulea, Sweden
   Phone: +46 8 404 29 43
   EMail: ghyslain.pelletier@ericsson.com

   Peter Kremer
   Conformance and Software Test Laboratory
   Ericsson Hungary
   H-1300 Bp. 3., P.O. Box 107, HUNGARY
   Phone: +36 1 437 7033
   EMail: peter.kremer@ericsson.com

























Jonsson, et al.                                                [Page 26]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


Appendix A - Sample CRC algorithm


   #!/usr/bin/perl -w
   use strict;
   #=================================
   #
   # ROHC CRC demo - Carsten Bormann cabo@tzi.org 2001-08-02
   #
   # This little demo shows the four types of CRC in use in RFC 3095,
   # the specification for robust header compression. Type your data in
   # hexadecimal form and then press Control+D.
   #
   #---------------------------------
   #
   # utility
   #
   sub dump_bytes($) {
       my $x = shift;
       my $i;
       for ($i = 0; $i < length($x); ) {
     printf("%02x ", ord(substr($x, $i, 1)));
     printf("\n") if (++$i % 16 == 0);
       }
       printf("\n") if ($i % 16 != 0);
   }

   #---------------------------------
   #
   # The CRC calculation algorithm.
   #
   sub do_crc($$$) {
       my $nbits = shift;
       my $poly = shift;
       my $string = shift;

       my $crc = ($nbits == 32 ? 0xffffffff : (1 << $nbits) - 1);
       for (my $i = 0; $i < length($string); ++$i) {
         my $byte = ord(substr($string, $i, 1));
         for( my $b = 0; $b < 8; $b++ ) {
           if (($crc & 1) ^ ($byte & 1)) {
             $crc >>= 1;
             $crc ^= $poly;
           } else {
           $crc >>= 1;
           }
           $byte >>= 1;
         }
       }
       printf "%2d bits, ", $nbits;
       printf "CRC: %02x\n", $crc;



Jonsson, et al.                                                [Page 27]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


   }

   #---------------------------------
   #
   # Test harness
   #
   $/ = undef;
   $_ = <>;         # read until EOF
   my $string = ""; # extract all that looks hex:
   s/([0-9a-fA-F][0-9a-fA-F])/$string .= chr(hex($1)), ""/eg;
   dump_bytes($string);

   #---------------------------------
   #
   # 32-bit segmentation CRC
   # Note that the text implies this is complemented like for PPP
   # (this differs from 8, 7, and 3-bit CRC)
   #
   #      C(x) = x^0 + x^1 + x^2 + x^4 + x^5 + x^7 + x^8 + x^10 +
   #             x^11 + x^12 + x^16 + x^22 + x^23 + x^26 + x^32
   #
   do_crc(32, 0xedb88320, $string);

   #---------------------------------
   #
   # 8-bit IR/IR-DYN CRC
   #
   #      C(x) = x^0 + x^1 + x^2 + x^8
   #
   do_crc(8, 0xe0, $string);

   #---------------------------------
   #
   # 7-bit FO/SO CRC
   #
   #      C(x) = x^0 + x^1 + x^2 + x^3 + x^6 + x^7
   #
   do_crc(7, 0x79, $string);

   #---------------------------------
   #
   # 3-bit FO/SO CRC
   #
   #      C(x) = x^0 + x^1 + x^3
   #
   do_crc(3, 0x6, $string);








Jonsson, et al.                                                [Page 28]

INTERNET-DRAFT Corrections and Clarifications to RFC 3095  May 22, 2006


Intellectual Property Statement

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights. Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard. Please address the information to the IETF at ietf-
   ipr@ietf.org.


Copyright Statement

   Copyright (C) The Internet Society (2006). This document is subject
   to the rights, licenses and restrictions contained in BCP 78, and
   except as set forth therein, the authors retain all their rights.


Disclaimer of Validity

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
   ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
   INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
   INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.





This Internet-Draft expires November 22, 2006.







Jonsson, et al.                                                [Page 29]


Html markup produced by rfcmarkup 1.109, available from https://tools.ietf.org/tools/rfcmarkup/