[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 RFC 3790

Network Working Group                               Philip J. Nesser II
draft-ietf-v6ops-ipv4survey-int-01.txt       Nesser & Nesser Consulting
Internet Draft                                        Cleveland Mickles
                                                        AOL Time Warner
                                                              June 2003
                                                  Expires December 2003

         Internet Area: Survey of IPv4 Addresses Currently Deployed


This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.

Status of this Memo

Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups.  Note that other
groups may also distribute working documents as Internet-Drafts.

Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents at
any time.  It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."

The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt

The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.

Mickles & Nesser        Expires - Dec. 2003                  [Page 01]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


Abstract

This document seeks to document all usage of IPv4 addresses in
currently deployed IETF Internet Area documented standards.  In order
to successfully transition from an all IPv4 Internet to an all IPv6
Internet, many interim steps will be taken. One of these steps is the
evolution of current protocols that have IPv4 dependencies.  It is
hoped that these protocols (and their implementations) will be
redesigned to be network address independent, but failing that will at
least dually support IPv4 and IPv6.  To this end, all Standards (Full,
Draft, and Proposed) as well as Experimental RFCs will be surveyed
and any dependencies will be documented.


1.0 Introduction.............................................02
2.0 Document Organization....................................03
3.0 Full Standards...........................................03
4.0 Draft Standards..........................................09
5.0 Proposed Standards.......................................13
6.0 Experimental RFCs........................................34
7.0  Summary of Results......................................43
8.0 Security Considerations..................................51
9.0 References...............................................51
10.0 Acknowledgements........................................51
11.0 Author's Addresses......................................52
12.0 Intellectual Property Statement.........................52
13.0  Full Copyright Statement...............................53

1.0 Introduction

This document is part of a document set aiming to document all usage of
IPv4 addresses in IETF standards. In an effort to have the information
in a manageable form, it has been broken into 7 documents conforming
to the current IETF areas (Application,  Internet, Management &
Operations, Routing, Security, Sub-IP and Transport).

This specific document focuses on usage of IPv4 addresses within the
Internet area.

For a full introduction, please see the intro[1] draft.

Mickles & Nesser        Expires - Dec. 2003                  [Page 02]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


2.0 Document Organization


The following sections 3, 4, 5, and 6 each describe the raw analysis
of Full, Draft, and Proposed Standards, and Experimental RFCs.  Each
RFC is discussed in turn starting with RFC 1 and ending with RFC 3247.
The comments for each RFC are "raw" in nature.  That is, each RFC is
discussed in a vacuum and problems or issues discussed do not "look
ahead" to see if any of the issues raised have already been fixed.

Section 7 is an analysis of the data presented in Sections 3, 4, 5,
and 6.  It is here that all of the results are considered as a whole
and the problems that have been resolved in later RFCs are correlated.


3.0 Full Standards

Full Internet Standards (most commonly simply referred to as
"Standards") are fully mature protocol specification that are widely
implemented and used throughout the Internet.


3.01 Internet Protocol. RFC0791, RFC0950, RFC0919, RFC0922, RFC792,
RFC1112

3.01.1 RFC 791 defines IPv4 and will be replaced by the IPv6
specifications.

3.01.2 RFC 950 specifies IPv4 subnetting and will be replaced by the
IPv6 specifications.

3.01.3 RFC 919 is not online and is unavailable for review.

3.01.4 RFC 922 specifies how broadcasts should be treated in the
presence of subnets.  The techniques of this document will be replaced
by the IPv6 specifications.

3.01.5 RFC 792 defines ICMP.  The specification of ICMPv6 will serve
as an update.

3.01.6 RFC 1112 defines IP multicast.  A similar updated version for
IPv6 multicasting must be written.


3.02 Domain Name System. RFC1034, RFC1035


Mickles & Nesser        Expires - Dec. 2003                  [Page 03]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


3.02.1 RFC 1034 Domain Concepts and Facilities

In Section 3.6. Resource Records the definition of A records is:

RDATA           which is the type and sometimes class dependent data
                which describes the resource:

                A               For the IN class, a 32 bit IP address

In Section 5.2.1. Typical functions defines

   1. Host name to host address translation.

      This function is often defined to mimic a previous HOSTS.TXT
      based function.  Given a character string, the caller wants
      one or more 32 bit IP addresses.  Under the DNS, it
      translates into a request for type A RRs.  Since the DNS does
      not preserve the order of RRs, this function may choose to
      sort the returned addresses or select the "best" address if
      the service returns only one choice to the client.  Note that
      a multiple address return is recommended, but a single
      address may be the only way to emulate prior HOSTS.TXT
      services.

   2. Host address to host name translation

      This function will often follow the form of previous
      functions.  Given a 32 bit IP address, the caller wants a
      character string.  The octets of the IP address are reversed,
      used as name components, and suffixed with "IN-ADDR.ARPA".  A
      type PTR query is used to get the RR with the primary name of
      the host.  For example, a request for the host name
      corresponding to IP address 1.2.3.4 looks for PTR RRs for
      domain name "4.3.2.1.IN-ADDR.ARPA".

There are, of course, numerous examples of IPv4 addresses scattered
throughout the document.  There is currently a large debate ongoing
in the DNS community over the use of A6 or AAAA record types for the
resolution of IPv6 addresses.  The fact that current A records are
insufficient to support IPv6 is not unknown to the Internet community.









Mickles & Nesser        Expires - Dec. 2003                  [Page 04]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


3.02.2 RFC 1035 DOMAIN NAMES - IMPLEMENTATION AND SPECIFICATION

Section 3.4.1. A RDATA format defines the format for A records:


          +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
          |                    ADDRESS                    |
          +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+

      where:

      ADDRESS         A 32 bit Internet address.

      Hosts that have multiple Internet addresses will have
      multiple A records.

      A records cause no additional section processing.  The
      RDATA section of an A line in a master file is an Internet
      address expressed as four decimal numbers separated by dots
      without any imbedded spaces (e.g.,"10.2.0.52" or "192.0.5.6").

Section 3.4.2. WKS RDATA format

    +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
    |                    ADDRESS                    |
    +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
    |       PROTOCOL        |                       |
    +--+--+--+--+--+--+--+--+                       |
    |                                               |
    /                   <BIT MAP>                   /
    /                                               /
    +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+

      where:

      ADDRESS         An 32 bit Internet address

      PROTOCOL        An 8 bit IP protocol number

      <BIT MAP>       A variable length bit map.  The bit map
                  must be a multiple of 8 bits long.

      The WKS record is used to describe the well known services
      supported by a particular protocol on a particular internet
      address.  The PROTOCOL field specifies an IP protocol number,
      and the bit map has one bit per port of the specified protocol.
      The first bit corresponds to port 0, the second to port 1, etc.
      If the bit map does not include a bit for a protocol of
      interest, that bit is assumed zero.  The appropriate values and
      mnemonics for ports and protocols are specified in [RFC-1010].

Mickles & Nesser        Expires - Dec. 2003                  [Page 05]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


      For example, if PROTOCOL=TCP (6), the 26th bit corresponds to
      TCP port 25 (SMTP).  If this bit is set, a SMTP server should be
      listening on TCP port 25; if zero, SMTP service is not supported
      on the specified address.

      The purpose of WKS RRs is to provide availability information for
      servers for TCP and UDP.  If a server supports both TCP and UDP,
      or has multiple Internet addresses, then multiple WKS RRs are
      used.

      WKS RRs cause no additional section processing.


      Section 3.5. IN-ADDR.ARPA domain describe reverse DNS lookups and
      is clearly IPv4 dependent.

There are, of course, numerous examples of IPv4 addresses scattered
throughout the document.


3.03 RFC 894 Standard for the transmission of IP datagrams over
Ethernet networks

This protocol specifically deals with the transmissions of IPv4 packets
over Ethernet.  A similar RFC must exist for transmission of IPv6
packets.


3.04 RFC 895 Standard for the transmission of IP datagrams over
experimental Ethernet networks

This protocol specifically deals with the transmissions of IPv4 packets
over Ethernet.  It is probably unnecessary to provide an updated RFC
because of the unlikelihood of the existence of this layer 2 medium.


3.05 RFC 1042 Standard for the transmission of IP datagrams over IEEE
802 networks

This protocol specifically deals with the transmissions of IPv4 packets
over Ethernet.  A similar RFC must exist for transmission of IPv6
packets, particularly for 802.5 networks.


3.06 RFC 891 DCN Local-Network Protocols

There are many implicit assumptions about the use of IPv4 addresses in
this document.  It is unlikely to require any updates since no DCN
networks are in existence.

Mickles & Nesser        Expires - Dec. 2003                  [Page 06]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


3.07 RFC 1044 Internet Protocol on Network System's HYPERchannel:
Protocol Specification

There are a variety of methods used in this standard to map IPv4
addresses to 32 bits fields in the HYPERchannel headers.  A new
version of the standard will need to be written do support IPv6 on
HYPERchannel networks.


3.08 RFC 1201 Transmitting IP traffic over ARCNET networks

The major concerns of this RFC with respect to IPv4 addresses occur
in the resolution of ARCnet 8bit addresses to IPv4 addresses in an
"ARPlike" method.
A similar method, very similar to this RFC, would need to be written
to support IPv6 addresses over ARCNET.


3.09 RFC 1055 Nonstandard for transmission of IP datagrams over serial
lines:
     SLIP

This RFC is more of a analysis of the shortcomings of SLIP which is
unsurprising.  The introduction of PPP as a general replacement of SLIP
has made this protocol essentially unused.  No update need be
considered.


3.10 RFC 1088 Standard for the transmission of IP datagrams over
     NetBIOS networks

This RFC documents a technique to encapsulate IP packets inside NetBIOS
packets.
The technique presented of using NetBIOS names of the form
IP.XX.XX.XX.XX will not work for IPv6 addresses since the length of
IPv6 addresses will not fit within the NetBIOS 15 octet name
limitation.  A new scheme must be invented to similarly encapsulate
IPv6 packets.


3.11 The Point-to-Point Protocol (PPP). RFC1661, RFC1662


3.11.1 RFC 1661 The Point-to-Point Protocol (PPP)

The Point-to-Point Protocol (PPP)

3.11.2 RFC 1662 PPP in HDLC-like Framing

There are no IPv4 dependencies in this protocol.

Mickles & Nesser        Expires - Dec. 2003                  [Page 07]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003



3.12 RFC 1209 The Transmission of IP Datagrams over the SMDS Service

This RFC defines running IPv4 and ARP over SMDS.  The methods described
could easily be extended to support IPv6 packets, but a new RFC would
be required.












































Mickles & Nesser        Expires - Dec. 2003                  [Page 08]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


4.0 Draft Standards

Draft Standards represent the penultimate standard level in the IETF.
A protocol can only achieve draft standard when there are multiple,
independent, interoperable implementations.  Draft Standards are
usually quite mature and widely used.


4.01 RFC 951 Bootstrap Protocol (BOOTP)

This protocol is designed specifically for use with IPv4.  A new
version will be required to support IPv6.  For example:

Section 3. Packet Format

   All numbers shown are decimal, unless indicated otherwise.  The
   BOOTP packet is enclosed in a standard IP [8] UDP [7] datagram.  For
   simplicity it is assumed that the BOOTP packet is never fragmented.
   Any numeric fields shown are packed in 'standard network byte
   order', i.e. high order bits are sent first.

   In the IP header of a bootrequest, the client fills in its own IP
   source address if known, otherwise zero.  When the server address is
   unknown, the IP destination address will be the 'broadcast address'
   255.255.255.255.  This address means 'broadcast on the local cable,
   (I don't know my net number)' [4].

...

      FIELD   BYTES   DESCRIPTION
      -----   -----   ---
...
         ciaddr  4       client IP address;
                         filled in by client in bootrequest if known.

         yiaddr  4       'your' (client) IP address;
                         filled by server if client doesn't
                         know its own address (ciaddr was 0).

         siaddr  4       server IP address;
                         returned in bootreply by server.

         giaddr  4       gateway IP address,
                         used in optional cross-gateway booting.

Since the packet format is a fixed 300 bytes in length, an updated
version of the protocol could easily accommodate an additional 48 bytes
(4 IPV6 fields of 16 bytes to replace the existing 4 IPv4 fields of
4 bytes).

Mickles & Nesser        Expires - Dec. 2003                  [Page 09]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003



4.02 RFC 1191 Path MTU discovery (IP-MTU)

The entire process of PMTU discovery is predicated on the use of the DF
bit in the IPv4 header, an ICMP message (also IPv4 dependent) and TCP
MSS option.  There clearly needs to an PMTUv6 functionality.


4.03-zzzz RFC 1356 Multiprotocol Interconnect on X.25 and ISDN

There are IPv4 dependencies within this RFC.

4.04 RFC 1534 Interoperation Between DHCP and BOOTP (DHCP-BOOTP)

There are no IPv4 dependencies in this protocol.


4.05 RFC 1542 Clarifications and Extensions for the Bootstrap Protocol

There are no new issues other than those presented in Section 4.01
above.

4.06 RFC 1629 Guidelines for OSI NSAP Allocation in the Internet
    (OSI-NSAP)

There are no IPv4 dependencies in this protocol.


4.07 RFC 1762 The PPP DECnet Phase IV Control Protocol (DNCP)
(PPP-DNCP)

There are no IPv4 dependencies in this protocol.


4.08 RFC 1989 PPP Link Quality Monitoring (PPP-LINK)

There are no IPv4 dependencies in this protocol.


4.09 RFC 1990 The PPP Multilink Protocol (MP) (PPP-MP)

Section 5.1.3.  Endpoint Discriminator Option defines a Class header
field.

   Class
        The Class field is one octet and indicates the identifier
        address space.  The most up-to-date values of the LCP Endpoint
        Discriminator Class field are specified in the most recent
        "Assigned Numbers" RFC [7].  Current values are assigned as
        follows:

Mickles & Nesser        Expires - Dec. 2003                  [Page 10]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


        0    Null Class

        1    Locally Assigned Address

        2    Internet Protocol (IP) Address

        3    IEEE 802.1 Globally Assigned MAC Address

        4    PPP Magic-Number Block

        5    Public Switched Network Directory Number

A new class field needs to be defined by the IANA for IPv6 addresses.

4.10 RFC 1994 PPP Challenge Handshake Authentication Protocol
     (CHAP) (PPP-CHAP)

There are no IPv4 dependencies in this protocol.

4.11 RFC 2067 IP over HIPPI (IP-HIPPI)

Section 5.1 Packet Formats contains the following excerpt:

   EtherType (16 bits) SHALL be set as defined in Assigned Numbers [8]:
   IP = 2048 ('0800'h), ARP = 2054 ('0806'h), RARP = 32,821 ('8035'h).

Section 5.5 MTU has the following definition:

   The MTU for HIPPI-SC LANs is 65280 bytes.

   This value was selected because it allows the IP packet to fit in
   one 64K byte buffer with up to 256 bytes of overhead.  The overhead
   is 40 bytes at the present time; there are 216 bytes of room for
   expansion.

         HIPPI-FP Header                  8 bytes
         HIPPI-LE Header                 24 bytes
         IEEE 802.2 LLC/SNAP Headers      8 bytes
         Maximum IP packet size (MTU) 65280 bytes
                                      ------------
                           Total      65320 bytes (64K - 216)

This definition is not applicable for IPv6 packets since packets can
be larger than the IPv4 limitation of 65280 bytes.

4.12 RFC 2131 Dynamic Host Configuration Protocol (DHCP)

This version of DHCP is highly assumptive of IPv4.  Significant work
on DHCPv6 has been done and is ongoing.

Mickles & Nesser        Expires - Dec. 2003                  [Page 11]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


4.13 RFC 2132 DHCP Options and BOOTP Vendor Extensions (DHCP-BOOTP)

This version of DHCP is highly assumptive of IPv4.  Significant work
on DHCPv6 has been done and is ongoing.

4.14-zzzz RFC 2332 NBMA Next Hop Resolution Protocol (NHRP)

There are IPv4 dependencies within this RFC.

4.15-zzzz RFC 2390 Inverse Address Resolution Protocol (IARP)

There are IPv4 dependencies within this RFC.

4.16-zzzz RFC 2427 Multiprotocol Interconnect over Frame Relay

There are IPv4 dependencies within this RFC.

4.17 RFC 2460 Internet Protocol, Version 6 (IPv6) Specification (IPV6)

This document defines IPv6 and has no IPv4 issues.


4.18 RFC 2461 Neighbor Discovery for IP Version 6 (IPv6) (IPV6-ND)

This document defines an IPv6 related protocol and has no IPv4 issues.


4.19 RFC 2462 IPv6 Stateless Address Autoconfiguration (IPV6-AUTO)

This document defines an IPv6 related protocol and has no IPv4 issues.


4.20 RFC 2463 Internet Control Message Protocol (ICMPv6) for the Internet
     Protocol Version 6 (IPv6) Specification (ICMPv6)

This document defines an IPv6 related protocol and has no IPv4 issues.













Mickles & Nesser        Expires - Dec. 2003                  [Page 12]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003

5.0 Proposed Standards

Proposed Standards are introductory level documents.  There are no
requirements for even a single implementation.  In many cases Proposed
are never implemented or advanced in the IETF standards process.  They
therefore are often just proposed ideas that are presented to the
Internet community.  Sometimes flaws are exposed or they are one of
many competing solutions to problems.  In these later cases, no
discussion is presented as it would not serve the purpose of this
discussion.

5.01 RFC 1234 Tunneling IPX traffic through IP networks (IPX-IP)

The section "Unicast Address Mappings" has the following text:

   For implementations of this memo, the first two octets of the host
   number will always be zero and the last four octets will be the
   node's four octet IP address.  This makes address mapping trivial
   for unicast transmissions: the first two octets of the host number
   are discarded, leaving the normal four octet IP address.  The
   encapsulation code should use this IP address as the destination
   address of the UDP/IP tunnel packet.

This mapping will not be able to work with IPv6 addresses.

There are also numerous discussions on systems keeping a "peer list"
to map between IP and IPX addresses.  The specifics are not discussed
in the document and are left to the individual implementation.

The section "Maximum Transmission Unit"

   Although larger IPX packets are possible, the standard maximum
   transmission unit for IPX is 576 octets.  Consequently, 576 octets
   is the recommended default maximum transmission unit for IPX packets
   being sent with this encapsulation technique.  With the eight octet
   UDP header and the 20 octet IP header, the resulting IP packets will
   be 604 octets long.  Note that this is larger than the 576 octet
   maximum size IP implementations are required to accept [3].  Any IP
   implementation supporting this encapsulation technique must be
   capable of receiving 604 octet IP packets.

   As improvements in protocols and hardware allow for larger,
   unfragmented IP transmission units, the 576 octet maximum IPX packet
   size may become a liability.  For this reason, it is recommended
   that the IPX maximum transmission unit size be configurable in
   implementations of this memo.

also has some implications on IP addressing.

Mickles & Nesser        Expires - Dec. 2003                  [Page 13]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


5.02 RFC 1256 ICMP Router Discovery Messages (ICMP-ROUT)

This RFC documents a protocol that is very specific to IPv4 and a
successor will be needed to provide the functionality.


5.03 RFC 1277 Encoding Network Addresses to Support Operation
      over Non-OSI Lower Layers

Section 4.5  TCP/IP (RFC 1006) Network Specific Format states:

The IDP and 2 digit prefix identifies a TCP/IP network where RFC 1006
is applied.  It is necessary to use an IP Address, as there are
insufficient bits to fit in a domain.  It is structured as follows:

      __________________________________________________________
      |_Digit___||_1-12____|13-17_(optional)_|18-22_(optional)_|_
      |_Meaning_||IP_Address_|____port_______|__Transport_Set__|_


For TCP/IP there shall be a 20 digit long network-specific part.
First 12 digits are for the IP address.  The port number can be up to
65535, and needs 5 digits (this is optional, and is defaulted as
defined in RFC 1006).  Finally, there is a third part to the address,
which is defined here as ``transport set'' that indicates what kind of
IP-based transport protocols is used.  This is a decimal number from
0-65535 which is really a 16-bit flag word.  1 is TCP, 2 is UDP.
Further values of this code are assigned by the IANA. If the transport
set is not there or no bits are set, it means ``default'' which is
TCP. This is encoded in 5 digits.

For example, the IP Address 10.0.0.6 with port 9 over UDP is encoded
as:

_______________________________________________________________________
|Part_____|_|_____IDP_________|___________________DSP__________________|
_
|Component|_|AFI__|___IDI_____|Prefix|___IP_Address____|_Port__|_T_Set_|
_
|Octet____|_|____|____________|_1-2__|______3-14_______|_15-19_|_20-24_|
_
|Value____|T|elex_|007_28722__|__03__|_010_000_000_006_|_00009_|_00002_|
__
|Cncrt_Dec|_|54___|007_28722__|__03__|_010_000_000_006_|_00009_|_00002_|
_
|Cncrt_Bin|_|54___|00_72_87_22_|_03__|01_00_00_00_00_06|00_00_9|0_00_02|
_

Mickles & Nesser        Expires - Dec. 2003                  [Page 14]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003



This 12 octet field for decimal versions of IP addresses is
insufficient for a decimal version of IPv6 addresses.  It is possible
to define a new encoding using the 20 digit long IP Address + Port +
Transport Set fields in order to accommodate a binary version of an
IPv6 address, port number and Transport Set.  There are several
schemes that could be envisioned.


5.04 RFC 1332 The PPP Internet Protocol Control Protocol (IPCP)
      (PPP-IPCP)

This document defines a protocol for devices to assign IPv4 addresses
to PPP clients once PPP negotiation is completed.  Section 3.  IPCP
Configuration Options defines the following:

The most up-to-date values of the IPCP Option Type field are specified
in the most recent "Assigned Numbers" RFC [6].  Current values are
assigned as follows:

   1       IP-Addresses
   2       IP-Compression-Protocol
   3       IP-Address

3.1.  IP-Addresses

   Description

      The use of the Configuration Option IP-Addresses has been
      deprecated.  It has been determined through implementation
      experience that it is difficult to ensure negotiation convergence
      in all cases using this option.  RFC 1172 [7] provides
      information for implementations requiring backwards
      compatibility.  The IP-Address Configuration Option replaces
      this option, and its use is preferred.

      This option should not be sent in a Configure-Request if a
      Configure-Request has been received which includes either an IP-
      Addresses or IP-Address option.  This option MAY be sent if a
      Configure-Reject is received for the IP-Address option, or a
      Configure-Nak is received with an IP-Addresses option as an
      appended option.

      Support for this option MAY be removed after the IPCP protocol
      status advances to Internet Draft Standard.




Mickles & Nesser        Expires - Dec. 2003                  [Page 15]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


3.3.  IP-Address

   Description

      This Configuration Option provides a way to negotiate the IP
      address to be used on the local end of the link.  It allows the
      sender of the Configure-Request to state which IP-address is
      desired, or to request that the peer provide the information.
      The peer can provide this information by NAKing the option, and
      returning a valid IP-address.

      If negotiation about the remote IP-address is required, and the
      peer did not provide the option in its Configure-Request, the
      option should be appended to a Configure-Nak.  The value of the
      IP-address given must be acceptable as the remote IP-address, or
      indicate a request that the peer provide the information.

      By default, no IP address is assigned.

   A summary of the IP-Address Configuration Option format is shown
   below.  The fields are transmitted from left to right.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |    Length     |           IP-Address
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
           IP-Address (cont)       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Type

      3

   Length

      6

   IP-Address

      The four octet IP-Address is the desired local address of the
      sender of a Configure-Request.  If all four octets are set to
      zero, it indicates a request that the peer provide the IP-Address
      information.

   Default

      No IP address is assigned.

Mickles & Nesser        Expires - Dec. 2003                  [Page 16]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


It is clearly designed to allow new Option Types to be added and should
offer no problems for use with IPv6 once appropriate options have been
defined.


5.05 RFC 1377 The PPP OSI Network Layer Control Protocol (OSINLCP)
      (PPP-OSINLC)

There are no IPv4 dependencies in this protocol.


5.06 RFC 1378 The PPP AppleTalk Control Protocol (ATCP) (PPP-ATCP)

There are no IPv4 dependencies in this protocol.


5.07 RFC 1469 IP Multicast over Token-Ring Local Area Networks
      (IP-TR-MC)

This document defines the usage of IPv4 multicast over IEEE 802.5
Token Ring networks.  A new method for IPv6 multicast over these
networks will need to be defined.


5.08 RFC 1552 The PPP Internetworking Packet Exchange Control
      Protocol (IPXCP) (IPXCP)

There are no IPv4 dependencies in this protocol.


5.09 RFC 1570 PPP LCP Extensions (PPP-LCP)

There are no IPv4 dependencies in this protocol.


5.10 RFC 1598 PPP in X.25 PPP-X25

There are no IPv4 dependencies in this protocol.


5.11 RFC 1618 PPP over ISDN (PPP-ISDN)

There are no IPv4 dependencies in this protocol.


5.12 RFC 1663 PPP Reliable Transmission (PPP-TRANS)

There are no IPv4 dependencies in this protocol.

Mickles & Nesser        Expires - Dec. 2003                  [Page 17]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003



5.13 RFC 1752 The Recommendation for the IP Next Generation Protocol
      (IPNG)

This document defines a roadmap for IPv6 development and is not
relevant to this discussion.


5.14 RFC 1755 ATM Signaling Support for IP over ATM (ATM)

There are no IPv4 dependencies in this protocol.


5.15 RFC 1763 The PPP Banyan Vines Control Protocol (BVCP) (BVCP)

There are no IPv4 dependencies in this protocol.


5.16 RFC 1764 The PPP XNS IDP Control Protocol (XNSCP) (XNSCP)

There are no IPv4 dependencies in this protocol.


5.17 RFC 1886 DNS Extensions to support IP version 6 (DNS-IPV6)

This RFC defines the AAAA record for IPv6 as well as PTR records
using the ip6.int domain.  There is currently a large debate going
on in the IPv6 and DNS community over the validity of AAAA versus
A6 records.


5.18 RFC 1973 PPP in Frame Relay (PPP-FRAME)

There are no IPv4 dependencies in this protocol.


5.19 RFC 1981 Path MTU Discovery for IP version 6 MTU-IPV6

This protocol describes an IPv6 related protocol and is not discussed
in this document.


5.20 RFC 1982 Serial Number Arithmetic (SNA)

There are no IPv4 dependencies in this protocol.


Mickles & Nesser        Expires - Dec. 2003                  [Page 18]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


5.21 RFC 1995 Incremental Zone Transfer in DNS (DNS-IZT)

Although the examples used in this document use IPv4 addresses,
(i.e. A records) there is nothing in the protocol to preclude
full and proper functionality using IPv6.

5.22 RFC 1996 A Mechanism for Prompt Notification of Zone Changes (DNS
      NOTIFY) (DNS-NOTIFY)

There are no IPv4 dependencies in this protocol.


5.23 RFC 2002 IP Mobility Support (MOBILEIPSU)

This document is designed for use in IPv4 networks.  There are
numerous referrals to other IP "support" mechanisms (i.e. ICMP
Router Discover Messages) that specifically refer to the IPv4
of ICMP.  An IP Mobility protocol for IPv6 is required.


5.24 RFC 2003 IP Encapsulation within IP (IPENCAPIP)

This document is designed for use in IPv4 networks.  There are
many referenced to a specified IP version number of 4 and 32-bit
addresses.  An IPv6 Encapsulation within IPv6 is required.


5.25 RFC 2004 Minimal Encapsulation within IP (MINI-IP)

This document is designed for use in IPv4 networks.  There are
many referenced to a specified IP version number of 4 and 32-bit
addresses.  A Minimal IPv6 Encapsulation within IPv6 is required.


5.26 RFC 2005 Applicability Statement for IP Mobility Support

This RFC documents the interoperation of IPv4 mobility as documented
in the preceding 3 section.


5.27 RFC 2022 Support for Multicast over UNI 3.0/3.1 based ATM
      Networks (MULTI-UNI)

This protocol specifically maps IPv4 multicast and a new version is
required to support IPv6 multicast.


5.28 RFC 2043 The PPP SNA Control Protocol (SNACP) (PPP-SNACP)

There are no IPv4 dependencies in this protocol.

Mickles & Nesser        Expires - Dec. 2003                  [Page 19]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003



5.29 RFC 2097 The PPP NetBIOS Frames Control Protocol (NBFCP)
      (PPP-NBFCP)

There are no IPv4 dependencies in this protocol.


5.30 RFC 2113 IP Router Alert Option (ROUT-ALERT)

This document provides a new mechanism for IPv4.  It is expected that
a similar functionality will be included in IPv6.


5.31 RFC 2125 The PPP Bandwidth Allocation Protocol (BAP) / The
      PPP Bandwidth Allocation Control Protocol (BACP) (BAP-BACP)

There are no IPv4 dependencies in this protocol.


5.32 RFC 2136 Dynamic Updates in the Domain Name System (DNS
      UPDATE) (DNS-UPDATE)

There are no IPv4 dependencies in this protocol.

5.33 RFC 2181 Clarifications to the DNS Specification (DNS-CLAR)

There are no IPv4 dependencies in this protocol.  The only reference
to IP addresses discuss the use of any cast address, so it should be
assumed that these mechanisms are IPv6 operable.

5.34 RFC 2225 Classical IP and ARP over ATM (IP-ATM)

>From the many references in this document it is clear that this
document is designed for IPv4 only.  It is only later in the
document that it is implicitly stated, as in:

     ar$spln -  length in octets of the source protocol address. Value
                range is 0 or 4 (decimal).  For IPv4 ar$spln is 4.

     ar$tpln -  length in octets of the target protocol address. Value
                range is 0 or 4 (decimal).  For IPv4 ar$tpln is 4.
and

   For backward compatibility with previous implementations, a null
   IPv4 protocol address may be received with length = 4 and an
   allocated address in storage set to the value 0.0.0.0.  Receiving
   stations must be liberal in accepting this format of a null IPv4
   address.  However, on transmitting an ATMARP or InATMARP packet, a
   null IPv4 address must only be indicated by the length set to zero
   and must have no storage allocated.

Mickles & Nesser        Expires - Dec. 2003                  [Page 20]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


A new specification for IPv6 must be defined.


5.35 RFC 2226 IP Broadcast over ATM Networks

This document is limited to IPv4 multicasting.  A new specification
for IPv6 must be defined.


5.36 RFC 2236 Internet Group Management Protocol, Version 2 (IGMP)

This document describes of version of IGMP used for IPv4 multicast.
A similar methodology for IPv6 multicast needs to be defined.


5.37 RFC 2241 DHCP Options for Novell Directory Services
      (DHCP-NDS)

This document defines extensions for the IPv4 only version of
DHCP and it is expected that similar options will be present in
DHCPv6.


5.38 RFC 2242 NetWare/IP Domain Name and Information (NETWAREIP)

Once again these are options to the IPv4 version of DHCP.  It is
expected that similar options will for IPv6 will exist in DHCPv6.

   PREFERRED_DSS (code 6)

      Length is (n * 4) and the value is an array of n IP addresses,
      each four bytes in length. The maximum number of addresses is 5
      and therefore the maximum length value is 20. The list contains
      the addresses of n NetWare Domain SAP/RIP Server (DSS).

   NEAREST_NWIP_SERVER (code 7)

      Length is (n * 4) and the value is an array of n IP addresses,
      each four bytes in length. The maximum number of addresses is 5
      and therefore the maximum length value is 20. The list contains
      the addresses of n Nearest NetWare/IP servers.

   PRIMARY_DSS (code 11)

      Length of 4, and the value is a single IP address.  This field
      identifies the Primary Domain SAP/RIP Service server (DSS) for
      this NetWare/IP domain. NetWare/IP administration utility uses
      this value as Primary DSS server when configuring a secondary
      DSS server.

Mickles & Nesser        Expires - Dec. 2003                  [Page 21]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003



5.39 RFC 2290 Mobile-IPv4 Configuration Option for PPP IPCP

This protocol is IPv4 specific.  It is expected that similar
methods will be developed for Mobile IPv6.


5.40 RFC 2308 Negative Caching of DNS Queries (DNS NCACHE)
      (DNS-NCACHE)

Although there are numerous examples in this document that use
IPv4 "A" records, there is nothing in the protocol that limits
its effectiveness to IPv4.


5.41 RFC 2331 ATM Signaling Support for IP over ATM - UNI Signaling
      4.0 Update (UNI-SIG)

There are no IPv4 dependencies in this protocol.

5.42-zzzz RFC 2333 NHRP Protocol Applicability

There are IPv4 dependencies within this RFC.

5.43-zzzz RFC 2335 A Distributed NHRP Service Using SCSP

There are IPv4 dependencies within this RFC.

5.44 RFC 2363 PPP Over FUNI (PPP-FUNI)

There are no IPv4 dependencies in this protocol.


5.45 RFC 2364 PPP Over AAL5 (PPP-AAL)

There are no IPv4 dependencies in this protocol.


5.46 RFC 2371 Transaction Internet Protocol Version 3.0 TIPV3

This document states:

   TIP transaction manager addresses take the form:

     <hostport><path>

   The <hostport> component comprises:

     <host>[:<port>]

Mickles & Nesser        Expires - Dec. 2003                  [Page 22]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


   where <host> is either a <dns name> or an <ip address>; and <port>
   is a decimal number specifying the port at which the transaction
   manager (or proxy) is listening for requests to establish TIP
   connections. If the port number is omitted, the standard TIP port
   number (3372) is used.

   A <dns name> is a standard name, acceptable to the domain name
   service. It must be sufficiently qualified to be useful to the
   receiver of the command.

   An <ip address> is an IP address, in the usual form: four decimal
   numbers separated by period characters.

and further along it states:

  A TIP URL takes the form:

     tip://<transaction manager address>?<transaction string>

   where <transaction manager address> identifies the TIP transaction
   manager (as defined in Section 7 above); and <transaction string>
   specifies a transaction identifier, which may take one of two forms
   (standard or non-standard):

   i. "urn:" <NID> ":" <NSS>

     A standard transaction identifier, conforming to the proposed
     Internet Standard for Uniform Resource Names (URNs), as specified
     by RFC2141; where <NID> is the Namespace Identifier, and <NSS> is
     the Namespace Specific String. The Namespace ID determines the
     syntactic interpretation of the Namespace Specific String. The
     Namespace Specific String is a sequence of characters representing
     a transaction identifier (as defined by <NID>). The rules for the
     contents of these fields are specified by [6] (valid characters,
     encoding, etc.).

     This format of <transaction string> may be used to express global
     transaction identifiers in terms of standard representations.
     Examples for <NID> might be <iso> or <xopen>. e.g.

       tip://123.123.123.123/?urn:xopen:xid

     Note that Namespace Ids require registration. See [7] for details
     on how to do this.

Mickles & Nesser        Expires - Dec. 2003                  [Page 23]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


   ii. <transaction identifier>

     A sequence of printable ASCII characters (octets with values in
     the range 32 through 126 inclusive (excluding ":") representing a
     transaction identifier. In this non-standard case, it is the
     combination of <transaction manager address> and <transaction
     identifier> which ensures global uniqueness. e.g.

       tip://123.123.123.123/?transid1

It is not hard to assume that the production of an updated protocol
specification that supports IPv6 could be accomplished.


5.47 RFC 2373 IP Version 6 Addressing Architecture,

This RFC documents IPv6 addressing and is not discussed in this
document.


5.48 RFC 2374 An IPv6 Aggregatable Global Unicast Address Format,

This RFC documents IPv6 addressing and is not discussed in this
document.


5.49 RFC 2464 Transmission of IPv6 Packets over Ethernet Networks

This RFC documents a method for transmitting IPv6 packets over
ethernet and is not considered in this discussion.


5.50 RFC 2470 Transmission of IPv6 Packets over Token Ring
      Networks

This RFC documents a method for transmitting IPv6 packets over
token ring and is not considered in this discussion.


5.51 RFC 2472 IP Version 6 over PPP (IPv6-PPP)

This RFC documents a method for transmitting IPv6 packets over
PPP and is not considered in this discussion.


5.52 RFC 2473 Generic Packet Tunneling in IPv6 Specification

This RFC documents an IPv6 aware protocol and is not considered
in this discussion.

Mickles & Nesser        Expires - Dec. 2003                  [Page 24]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


5.53 RFC 2484 PPP LCP Internationalization Configuration Option

There are no IPv4 dependencies in this protocol.


5.54 RFC 2485 DHCP Option for The Open Group's User
      Authentication Protocol

This document defines extensions for the IPv4 only version of
DHCP and it is expected that similar options will be present in
DHCPv6.


5.55 RFC 2486 The Network Access Identifier (NAI)

There are no IPv4 dependencies in this protocol.


5.56 RFC 2491 IPv6 over Non-Broadcast Multiple Access
      (NBMA) networks (IPv6-NBMA)

This RFC documents a method for transmitting IPv6 packets over
NBMA networks and is not considered in this discussion.


5.57 RFC 2492 IPv6 over ATM Networks (IPv6ATMNET)

This RFC documents a method for transmitting IPv6 packets over
ATM networks and is not considered in this discussion.


5.58 RFC 2497 Transmission of IPv6 Packets over ARCnet
      Networks

This RFC documents a method for transmitting IPv6 packets over
ARCnet networks and is not considered in this discussion.


5.59 RFC 2507 IP Header Compression

This protocol is both IPv4 and IPv6 aware.


5.60 RFC 2526 Reserved IPv6 Subnet Anycast Addresses

This RFC documents IPv6 addressing and is not discussed in this
document.


Mickles & Nesser        Expires - Dec. 2003                  [Page 25]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


5.61 RFC 2529 Transmission of IPv6 over IPv4 Domains without
      Explicit Tunnels

This RFC documents IPv6 transmission methods and is not discussed
in this document.


5.62 RFC 2563 DHCP Option to Disable Stateless Auto-Configuration
      in IPv4 Clients

This document is only designated for IPv4.  It is expected that
similar functionality is available in DHCPv6.


5.63 RFC 2590 Transmission of IPv6 Packets over Frame Relay
      Networks Specification

This RFC documents IPv6 transmission method over Frame Relay and is
not discussed in this document.


5.64-zzzz RFC 2601 ILMI-Based Server Discovery for ATMARP

There are IPv4 dependencies within this RFC.

5.65-zzzz RFC 2602 ILMI-Based Server Discovery for MARS

There are IPv4 dependencies within this RFC.

5.66-zzzz RFC 2603 ILMI-Based Server Discovery for NHRP

There are IPv4 dependencies within this RFC.

5.67 RFC 2610 DHCP Options for Service Location Protocol

This document is only designated for IPv4.  It is expected that
similar functionality is available in DHCPv6.


5.68 RFC 2615 PPP over SONET/SDH

There are no IPv4 dependencies in this protocol.


5.69 RFC 2671 Extension Mechanisms for DNS (EDNS0) (EDNS0)

There are no IPv4 dependencies in this protocol.


Mickles & Nesser        Expires - Dec. 2003                  [Page 26]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


5.70 RFC 2672 Non-Terminal DNS Name Redirection

This document is only defined for IPv4 addresses.  A similar
specification for IPv6 addresses should be defined.


5.71 RFC 2673 Binary Labels in the Domain Name System (DNS)

This document is only defined for IPv4 addresses.  A similar
specification for IPv6 addresses should be defined.


5.72 RFC 2675 IPv6 Jumbograms

This document defines a IPv6 packet format and is therefore not
discussed in this document.

5.73-zzzz RFC 2684 Multiprotocol Encapsulation over ATM Adaptation

There are IPv4 dependencies within this RFC.

5.74 RFC 2686 The Multi-Class Extension to Multi-Link PPP

There are no IPv4 dependencies in this protocol.


5.75 RFC 2687 PPP in a Real-time Oriented HDLC-like Framing

There are no IPv4 dependencies in this protocol.


5.76 RFC 2688 Integrated Services Mappings for Low Speed Networks

There are no IPv4 dependencies in this protocol.


5.77 RFC 2710 Multicast Listener Discovery (MLD) for IPv6
      (MLD-IPv6)

This document defines an IPv6 specific protocol and is not discussed
in this document.


5.78 RFC 2711 IPv6 Router Alert Option

This document defines an IPv6 specific protocol and is not discussed
in this document.


Mickles & Nesser        Expires - Dec. 2003                  [Page 27]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


5.79 RFC 2728 The Transmission of IP Over the Vertical Blanking
      Interval of a Television Signal

The following data format is defined:

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |0|    group    |         uncompressed IP header (20 bytes)     |
    +-+-+-+-+-+-+-+-+                                               +
    |                                                               |
    :                             ....                              :
    +               +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |               |        uncompressed UDP header (8 bytes)      |
    +-+-+-+-+-+-+-+-+                                               +
    |                                                               |
    +               +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |               |              payload  (<1472 bytes)           |
    +-+-+-+-+-+-+-+-+                                               +
    |                                                               |
    :                              ....                             :
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                              CRC                              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

This protocol is IPv4 dependent.  Updates must be made to support
IPv6.


5.80 RFC 2734 IPv4 over IEEE 1394

This protocol is IPv4 only.  A similar document must be defined for
IPv6.

5.81-zzzz RFC 2735 NHRP Support for Virtual Private Networks

There are IPv4 dependencies within this RFC.

5.82 RFC 2765 Stateless IP/ICMP Translation Algorithm (SIIT)
      (SIIT)

This protocol defines a method for IPv6 transition and is not
discussed in this document.


5.83 RFC 2766 Network Address Translation - Protocol
      Translation (NAT-PT) (NAT-PT)

This protocol defines a method for IPv6 transition and is not
discussed in this document.

Mickles & Nesser        Expires - Dec. 2003                  [Page 28]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


5.84 RFC 2776 Multicast-Scope Zone Announcement Protocol (MZAP)
      (MZAP)

This protocol is both IPv4 and IPv6 aware and needs no changes.


5.85 RFC 2782 A DNS RR for specifying the location of services
(DNS-SRV)

There are no IPv4 dependencies in this protocol.


5.86 RFC 2794 Mobile IP Network Access Identifier Extension for
     IPv4

This document defines an IPv4 specific protocol and a similar
functionality must be defined for Mobile IPv6.


5.87 RFC 2834 ARP and IP Broadcast over HIPPI-800

This document uses the generic term "IP Address" in the text but
it also contains the text:

   The HARP message has several fields that have the following format
   and values:

   Data sizes and field meaning:
     ar$hrd  16 bits  Hardware type
     ar$pro  16 bits  Protocol type of the protocol fields below
     ar$op   16 bits  Operation code (request, reply, or NAK)
     ar$pln   8 bits  byte length of each protocol address
     ar$rhl   8 bits  requester's HIPPI hardware address length (q)
     ar$thl   8 bits  target's HIPPI hardware address length (x)
     ar$rpa  32 bits  requester's protocol address
     ar$tpa  32 bits  target's protocol address
     ar$rha  qbytes   requester's HIPPI Hardware address
     ar$tha  xbytes   target's HIPPI Hardware address

   Where :
     ar$hrd  - SHALL contain 28. (HIPARP)

     ar$pro  - SHALL contain the IP protocol code 2048 (decimal).

     ar$op   - SHALL contain the operational value (decimal):
               1  for   HARP_REQUESTs
               2  for   HARP_REPLYs
               8  for InHARP_REQUESTs
               9  for InHARP_REPLYs
               10 for   HARP_NAK

Mickles & Nesser        Expires - Dec. 2003                  [Page 29]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


     ar$pln  - SHALL contain 4.

and later:

      31    28        23  21          15        10     7         2   0
      +-----+---------+-+-+-----------+---------+-----+---------+-----+
    0 |      04       |1|0|         000         |      03       |  0  |
      +---------------+-+-+---------------------+---------------+-----+
    1 |                              45                               |
      +-----+-+-------+-----------------------+-----------------------+
    2 |[LA] |W|MsgT= 0|          000          |   Dest. Switch Addr   |
      +-----+-+-------+-----------------------+-----------------------+
    3 |   2   |   2   |          000          |  Source Switch Addr   |
      +---------------+---------------+-------+-----------------------+
    4 |             00 00             |                               |
      +-------------------------------+                               |
    5 |                      Destination ULA                          |
      +-------------------------------+-------------------------------+
    6 |             [LA]              |                               |
      +-------------------------------+                               |
    7 |                         Source ULA                            |
      +===============+===============+===============+===============+
    8 |       AA      |      AA       |       03      |       00      |
      +---------------+---------------+---------------+---------------+
    9 |       00      |      00       |        Ethertype (2054)       |
      +---------------+---------------+-------------------------------+
   10 |              hrd (28)         |           pro (2048)          |
      +---------------+---------------+---------------+---------------+
   11 |             op (ar$op)        |     pln (6)   |   rhl (q)     |
      +---------------+---------------+---------------+---------------+
   12 |    thl = (x)  |   Requester IP Address upper  (24 bits)       |
      +---------------------------------------------------------------+
   13 | Req. IP lower |      Target IP Address upper  (24 bits)       |
      +---------------+-----------------------------------------------+
   14 | Tgt. IP lower | Requester HIPPI Hardware Address bytes 0 - 2  |
      +---------------+-----------------------------------------------+
   15 |         Requester HIPPI Hardware Address bytes 3 - 6          |
      +-----------------------------------------------+---------------+
   16 |         Requester HW Address bytes 7 - q      | Tgt HW byte 0 |
      +---------------+---------------+---------------+---------------+
   17 |          Target  HIPPI Hardware Address bytes 1 - 4           |
      +---------------------------------------------------------------+
   18 |          Target  HIPPI Hardware Address bytes 5 - 8           |
      +---------------+---------------+---------------+---------------+
   19 |Tgt HW byte 9-x|     FILL      |     FILL      |     FILL      |
      +---------------+---------------+---------------+---------------+
                           HARP - InHARP Message
Which make this protocol only IPv4 aware.  An update is required to
support IPv6.

Mickles & Nesser        Expires - Dec. 2003                  [Page 30]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003



5.88 RFC 2835 IP and ARP over HIPPI-6400 (GSN) (GSN)

This document states:

   The Ethertype value SHALL be set as defined in Assigned Numbers [18]:

   IP           0x0800  2048  (16 bits)

This is IPv4 limited and as expected (after reviewing the previous
section) requires an update to support IPv6.  There are numerous other
points in the documents that confirms this assumption.


5.89 RFC 2855 DHCP for IEEE 1394

This document is only designated for IPv4.  It is expected that
similar functionality is available in DHCPv6.


5.90 RFC 2874 DNS Extensions to Support IPv6 Address Aggregation
      and Renumbering

This document defines a protocol to interact with IPv6 and is not
considered in this document.


5.91 RFC 2893 Transition Mechanisms for IPv6 Hosts and Routers
      (TRANS-IPV6)

This document defines a transition mechanism for IPv6 and is not
considered in this document.


5.92 RFC 2915 The Naming Authority Pointer (NAPTR) DNS Resource
      Record (NAPTR)

There are no IPv4 dependencies in this protocol.


5.93 RFC 2916 E.164 number and DNS

There are no IPv4 dependencies in this protocol.


5.94 RFC 2937 The Name Service Search Option for DHCP

This document is only designated for IPv4.  It is expected that
similar functionality is available in DHCPv6.

Mickles & Nesser        Expires - Dec. 2003                  [Page 31]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


5.95 RFC 3004 The User Class Option for DHCP

This document is only designated for IPv4.  It is expected that
similar functionality is available in DHCPv6.


5.96 RFC 3011 The IPv4 Subnet Selection Option for DHCP

This document is specifically designed for IPv4.


5.97 RFC 3021 Using 31-Bit Prefixes on IPv4 Point-to-Point Links

This document is IPv4 specific and a similar technique could also
be defined for IPv6.


5.98 RFC 3024 Reverse Tunneling for Mobile IP, revised

This protocol assumes IPv4 addressing.  An updated Mobile IPv6
specification should include this functionality.


5.99 RFC 3046 DHCP Relay Agent Information Option

This document is only designated for IPv4.  It is expected that
similar functionality is available in DHCPv6.


5.100 RFC 3056 Connection of IPv6 Domains via IPv4 Clouds

This is an IPv6 related document and is not discussed in this
document.


5.101 RFC 3068 An Anycast Prefix for 6to4 Relay Routers

This is an IPv6 related document and is not discussed in this
document.


5.102 RFC 3074 DHC Load Balancing Algorithm

There are no IPv4 dependencies in this protocol.


5.103 RFC 3077 A Link-Layer Tunneling Mechanism for Unidirectional
      Links

This protocol is both IPv4 and IPv6 aware and needs no changes.

Mickles & Nesser        Expires - Dec. 2003                  [Page 32]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003



5.104 RFC 3115 Mobile IP Vendor/Organization-Specific Extensions

This is an enhancement for Mobile IPv4.  It is expected that a
similar capability will be in Mobile IPv6.


5.105 RFC 3145 L2TP Disconnect Cause Information

There are no IPv4 dependencies in this protocol.







































Mickles & Nesser        Expires - Dec. 2003                  [Page 33]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


6.0 Experimental RFCs

Experimental RFCs typically define protocols that do not have widescale
implementation or usage on the Internet.  They are often propriety in
nature or used in limited arenas.  They are documented to the Internet
community in order to allow potential interoperability or some other
potential useful scenario.  In a few cases they are presented as
alternatives to the mainstream solution to an acknowledged problem.


6.01 RFC 1183 New DNS RR Definitions (DNS-RR)

There are no IPv4 dependencies in this protocol.


6.02 RFC 1226 Internet protocol encapsulation of AX.25 frames
      (IP-AX.25)

There are no IPv4 dependencies in this protocol.


6.03 RFC 1241 Scheme for an internet encapsulation protocol: Version
      1 (IN-ENCAP)

This protocol specifies a protocol that assumes IPv4 but does not
actually have any limitations which would limit its operation in
an IPv6 environment.


6.04 RFC 1393 Traceroute Using an IP Option (TRACE-IP)

This document uses an IPv4 option.  It is therefore limited to IPv4
networks.  A different technique must be developed for IPv6.


6.05 RFC 1433 Directed ARP (DIR-ARP)

There are no IPv4 dependencies in this protocol.


6.06 RFC 1464 Using the Domain Name System To Store Arbitrary String
      Attributes

There are no IPv4 dependencies in this protocol.


Mickles & Nesser        Expires - Dec. 2003                  [Page 34]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


6.07 RFC 1475 TP/IX: The Next Internet (TP-IX)

This document defines IPv7 and has been abandoned by the IETF as a
feasible design.  It is not considered in this document.


6.08 RFC 1561 Use of ISO CLNP in TUBA Environments (CLNP-TUBA)

This document defines the use of NSAPA addressing and does not
use any version of IP, so there are no IPv4 dependencies in this
protocol.


6.09 RFC 1712 DNS Encoding of Geographical Location (DNS-ENCODE)

There are no IPv4 dependencies in this protocol.


6.10 RFC 1735 NBMA Address Resolution Protocol (NARP) (NARP)

This document defines a protocol that is IPv4 specific.  A new
version would need to be documented to support IPv6.

4. Packet Formats

   NARP requests and replies are carried in IP packets as protocol type
   54.  This section describes the packet formats of NARP requests and
   replies:

   NARP Request

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |    Version    |   Hop Count   |          Checksum             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |     Type      |    Code       |           Unused              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    Destination IP address                     |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                      Source IP address                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | NBMA length   |                NBMA address                   |
      +-+-+-+-+-+-+-+-+                                               |
      |                  (variable length)                            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Source and Destination IP Addresses
     Respectively, these are the IP addresses of the NARP requestor and
     the target terminal for which the NBMA address is desired.

Mickles & Nesser        Expires - Dec. 2003                  [Page 35]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003

and

   NARP Reply

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |    Version    |   Hop Count   |          Checksum             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |     Type      |      Code     |           Unused              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                    Destination IP address                     |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                      Source IP address                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | NBMA length   |                NBMA address                   |
      +-+-+-+-+-+-+-+-+                                               |
      |                  (variable length)                            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Source and Destination IP Address
     Respectively, these are the IP addresses of the NARP requestor and
     the target terminal for which the NBMA address is desired.


6.11 RFC 1768 Host Group Extensions for CLNP Multicasting (CLNP-MULT)

This document defines an IPv9 multicast protocol and has been
abandoned by the IETF as a feasible design.  It is not considered in
this document.


6.12 RFC 1788 ICMP Domain Name Messages (ICMP-DM)

This protocol is used for updates to the in-addr.arp reverse DNS
maps, and is limited to IPv4.


6.13 RFC 1797 Class A Subnet Experiment

This document is specific to IPv4.


6.14 RFC 1819 Internet Stream Protocol Version 2 (ST2) Protocol
      Specification - Version ST2+ (ST2)

This protocol is IPv4 limited.  In fact it is the definition of
IPv5.  See below.

Mickles & Nesser        Expires - Dec. 2003                  [Page 36]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


   Both ST2 and IP apply the same addressing schemes to identify
   different hosts. ST2 and IP packets differ in the first four bits,
   which contain the internetwork protocol version number: number 5 is
   reserved for ST2 (IP itself has version number 4). As a network
   layer protocol, like IP, ST2 operates independently of its
   underlying subnets. Existing implementations use ARP for address
   resolution, and use the same Layer 2 SAPs as IP.

8.2  Group Name Generator

   GroupName generation is similar to Stream ID generation. The
   GroupName includes a 16-bit unique identifier, a 32-bit creation
   timestamp, and a 32-bit IP address. Group names are globally unique.
   A GroupName includes the creator's IP address, so this reduces a
   global uniqueness problem to a simple local problem.

   IP-encapsulated ST packets begin with a normal IP header. Most
   fields of the IP header should be filled in according to the same
   rules that apply to any other IP packet. Three fields of special
   interest are:

o   Protocol is 5, see [RFC1700], to indicate an ST packet is enclosed,
    as opposed to TCP or UDP, for example.

and

   The following permanent IP multicast addresses have been assigned to
   ST:

           224.0.0.7 All ST routers (intermediate agents)
           224.0.0.8 All ST hosts (agents)

   In addition, a block of transient IP multicast addresses,
   224.1.0.0 -224.1.255.255, has been allocated for ST multicast
   groups. For instance, the following two functions could be made
   available:

   The ST Header also includes an ST Version Number, a total length
   field, a header checksum, a unique id, and the stream origin 32-bit
   IP address. The unique id and the stream origin 32-bit IP address
   form the stream id (SID). This is shown in Figure 10. Please refer
   to Section 10.6 for an explanation of the notation.

Mickles & Nesser        Expires - Dec. 2003                  [Page 37]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  ST=5 | Ver=3 |D| Pri |   0   |            TotalBytes         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |          HeaderChecksum       |            UniqueID           |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                         OriginIPAddress                       |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                            Figure 10: ST Header

o   ST is the IP Version Number assigned to identify ST packets. The
    value for ST is 5.

o   OriginIPAddress is the second element of the SID. It is the 32-bit
    IP address of the stream origin, see Section 8.1.

10.3.2  Group

   The Group parameter (PCode = 2) is an optional argument used to
   indicate that the stream is a member in the specified group.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  PCode = 2    |   PBytes = 16 |           GroupUniqueID       |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                        GroupCreationTime                      |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     GroupInitiatorIPAddress                   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |            Relationship       |                 N             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                         Figure 13: Group Parameter

o   GroupUniqueID, GroupInitiatorIPAddress, and GroupCreationTime
    together form the GroupName field. They are allocated by the group
    name generator function, see Section 8.2. GroupUniqueID and
    GroupCreationTime are implementation specific and have only local
    definitions.

10.3.3  MulticastAddress

   The MulticastAddress parameter (PCode = 3) is an optional parameter
   that is used when using IP encapsulation and setting up an IP
   multicast group. This parameter is used to communicate the desired
   IP multicast address to next-hop ST agents that should become
   members of the group, see Section 8.8.

Mickles & Nesser        Expires - Dec. 2003                  [Page 38]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  PCode = 3    |   PBytes = 8  |                0              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                        IPMulticastAddress                     |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                        Figure 15:  MulticastAddress

o   IPMulticastAddress is the 32-bit IP multicast address to be used
    to receive data packets for the stream.

10.3.5  RecordRoute

   The RecordRoute parameter (PCode = 5) is used to request that the
   route between the origin and a target be recorded and delivered to
   the user application. The ST agent at the origin (or target)
   including this parameter, has to determine the parameter's length,
   indicated by the PBytes field. ST agents processing messages
   containing this parameter add their receiving IP address in the
   position indicated by the FreeOffset field, space permitting. If no
   space is available, the parameter is passed unchanged. When included
   by the origin, all agents between the origin and the target add
   their IP addresses and this information is made available to the
   application at the target. When included by the target, all agents
   between the target and the origin, inclusive, add their IP addresses
   and this information is made available to the application at the
   origin.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |   PCode = 5   |     PBytes    |       0       |  FreeOffset   |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                          IP Address 1                         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      :                              ...                              :
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                          IP Address N                         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                           Figure 17: RecordRoute

o   PBytes is the length of the parameter in bytes. Length is
    determined by the agent (target or origin) that first introduces
    the parameter.  Once set, the length of the parameter remains
    unchanged.

Mickles & Nesser        Expires - Dec. 2003                  [Page 39]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


o   FreeOffset indicates the offset, relative to the start of the
    parameter, for the next IP address to be recorded. When the
    FreeOffset is greater than, or equal to, PBytes the RecordRoute
    parameter is full.

o   IP Address is filled in, space permitting, by each ST agent
    processing this parameter.

10.3.6  Target and TargetList

   Several control messages use a parameter called TargetList (PCode =
   6), which contains information about the targets to which the
   message pertains. For each Target in the TargetList, the information
   includes the 32-bit IP address of the target, the SAP applicable to
   the next higher layer protocol, and the length of the SAP
   (SAPBytes). Consequently, a Target structure can be of variable
   length. Each entry has the format shown in Figure 18.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                        Target IP Address                      |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  TargetBytes  |  SAPBytes     |     SAP       :    Padding    |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                             Figure 18: Target

There are many other examples, but it does not serve any purpose to
include them all.


6.15 RFC 1868 ARP Extension - UNARP (UNARP)

This protocol specifies IPv4 ARP.  It is expected that a similar
method should be implemented in IPv6.


6.16 RFC 1876 A Means for Expressing Location Information in the
      Domain Name System (DNS-LOC)

This document defines a methodology for applying this technology
which is IPv4 dependent.  The protocol itself has no IPv4
dependencies.

6.17 RFC 1888 OSI NSAPs and IPv6

This is an IPv6 related document and is not discussed in this
document.

Mickles & Nesser        Expires - Dec. 2003                  [Page 40]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


6.18 RFC 2009 GPS-Based Addressing and Routing (GPS-AR)

The document states:

   The future version of IP (IP v6) will certainly have a sufficient
   number of bits in its addressing space to provide an address for
   even smaller GPS addressable units.  In this proposal, however, we
   assume the current version of IP (IP v4) and we make sure that we
   manage the addressing space more economically than that.  We will
   call the smallest GPS addressable unit a GPS-square.


6.19 RFC 2143 Encapsulating IP with the Small Computer System
      Interface (IP-SCSI)

This protocol will only operate using IPv4.  As stated in the
document:

   It was decided that the ten byte header offers the greatest
   flexibility for encapsulating version 4 IP datagrams for the
   following reasons:


6.20 RFC 2345 Domain Names and Company Name Retrieval

There are no IPv4 dependencies in this protocol.


6.21-zzzz RFC 2443 A Distributed MARS Service Using SCSP (MARS-SCSP)

There are IPv4 dependencies within this RFC.

6.22 RFC 2471 IPv6 Testing Address Allocation

This is an IPv6 related document and is not discussed in this
document.


6.23 RFC 2481 A Proposal to add Explicit Congestion Notification
      (ECN) to IP (ECN-IP)

This protocol is both IPv4 and IPv6 aware and needs no changes.

6.24-zzzz RFC 2520 NHRP with Mobile NHCs

There are IPv4 dependencies within this RFC.

6.25 RFC 2521 ICMP Security Failures Messages (ICMP-SEC)

There are no IPv4 dependencies in this protocol.

Mickles & Nesser        Expires - Dec. 2003                  [Page 41]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


6.26 RFC 2540 Detached Domain Name System (DNS) Information
      (DNS-INFO)

There are no IPv4 dependencies in this protocol.


6.27 RFC 2770 GLOP Addressing in 233/8

This document is specific to IPv4.


6.28 RFC 2823 PPP over Simple Data Link (SDL) using SONET/SDH with
      ATM-like framing (PPP-SDL)

There are no IPv4 dependencies in this protocol.


6.29 RFC 3123 A DNS RR Type for Lists of Address Prefixes (APL RR)

This protocol is both IPv4 and IPv6 aware and needs no changes.


Mickles & Nesser        Expires - Dec. 2003                  [Page 42]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


7.0  Summary of Results

In the initial survey of RFCs 62 positives were identified out of a
total of 159, broken down as follows:

        Standards                                16 of 18 or 88.89%
        Draft Standards                           6 of 16 or 37.50%
        Proposed Standards                       35 of 98 or 35.71%
        Experimental RFCs                         5 of 27 or 18.52%

Of those identified many require no action because they document
outdated and unused protocols, while others are document protocols
that are actively being updated by the appropriate working groups.
Additionally there are many instances of standards that should be
updated but do not cause any operational impact if they are not
updated.  The remaining instances are documented below.


7.1  Standards


7.1.01  STD3  Requirements for Internet Hosts (RFC 1122 )

RFC 1122 is essentially a requirements document for IPv4 hosts and a
similar document for IPv6 hosts should be written.


7.1.02 STD 5 Internet Protocol (RFC 791, 922, 792, & 1122)

RFC 791 has been updated in the definition of IPv6 in RFC 2460.

RFC 922 has been included in the IPv6 Addressing Architecture, RFC
2373.

RFC 792 has been updated in the definition of ICMPv6 in RFC 2463.

RFC 1122 has been updated in the definition of Multicast Listener
Discovery in RFC 2710.


7.1.03 STD 13 Domain Name System (RFCs 1034 & 1035)

New resource records for IPv6 addresses have been defined (AAAA & A6).

7.1.04 STD 41 IP over Ethernet (RFC 894)

This problem has been fixed by RFC2464, A Method for the Transmission
of IPv6 Packets over Ethernet Networks.

Mickles & Nesser        Expires - Dec. 2003                  [Page 43]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003



7.1.05 STD 42 IP over Experimental Ethernets (RFC 895)

See above section.


7.1.06 STD 43 IP over IEEE 8.02 (RFC 1042)

The functionality of this RFC is included in subsequent standards
defining IPv6 over XXX.


7.1.07 STD 44 DCN Networks (RFC 891)

This protocol is no longer used and an updated protocol should not be
created.


7.1.08 STD 45 IP over HyperChannel (RFC 1044)

No updated document exists for this protocol.  It is unclear whether
one is needed.  An updated protocol MAY be created.


7.1.09 STD 46 IP over Arcnet (RFC 1201)

This problem has been fixed by RFC 2497, A Method for the
Transmission of IPv6 Packets over ARCnet Networks.


7.1.10 STD 48 IP over Netbios (RFC 1088)

A new protocol specification for tunneling IPv6 packets through
Netbios networks should be defined.


7.1.11 STD 52 IP over SMDS (RFC 1209)

An updated protocol for the transmission of IPv6 packets over SMDS
must be written.

7.2 Draft Standards


7.2.1 Boot Protocol (RFC 951)

This problem has been fixed in the DHCPv6 and Auto Configuration
protocols of IPv6: RFC 2462: IPv6 Stateless Address Autoconfiguration,
and Dynamic Host Configuration Protocol for IPv6 (DHCPv6) currently an
Internet Draft.

Mickles & Nesser        Expires - Dec. 2003                  [Page 44]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003



7.2.2 Path MTU Discovery (RFC 1191)

This problem has been fixed in RFC 1981, Path MTU Discovery for IP
version 6.


7.2.3 The PPP Multilink Protocol (RFC 1990)

A new class identifier for IPv6 packets must be registered with
the IANA.  It is RECOMMENDED that the (currently unassigned) value of
6 be assigned by the IANA with a description of "Internet Protocol
(IPv6) Address."  An application for this assignment has been sent to
the IANA.


7.2.4 IP over HIPPI (RFC 2067)

An updated protocol for the transmission of IPv6 packets over HIPPI MAY
be written.


7.2.5 DHCP (RFC 2131)

The problems are being fixed by the work of the DHC WG.  Several very
advanced IDs address all the issues.


7.2.6 DHCP Options (RFC 2132)

The problems are being fixed by the work of the DHC WG.  Several very
advanced IDs address all the issues.



7.3  Proposed Standards


7.3.01 Tunneling IPX over IP (RFC 1234)

This problem remains unresolved and a new protocol specification
must be created.


7.3.02 ICMP Router Discovery (RFC 1256)

This problem has been resolved in RFC 2461, Neighbor Discovery for
IP Version 6 (IPv6)

Mickles & Nesser        Expires - Dec. 2003                  [Page 45]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


7.3.03 Encoding Net Addresses to Support Operation Over Non OSI Lower
      Layers (RFC 1277)

This problem is unresolved, but it MAY be resolved with the creation
of a new encoding scheme definition.


7.3.04 PPP Internet Protocol Control Protocol (RFC 1332)

This problem has been resolved in RFC 2472, IP Version 6 over PPP.


7.3.05 IP Multicast over Token Ring (RFC 1469)

The functionality of this specification has been essentially covered
in RFC 2470, IPv6 over Token Ring in section 8.


7.3.06  IP Mobility Support (RFC 2002)

The problems are being resolved by the Mobile IP WG and there is
a mature ID (draft-ietf-mobileip-ipv6-15.txt)


7.3.07  IP Encapsulation within IP (RFC 2003)

This functionality for Mobile IPv6 is accomplished using the Routing
Header as defined in RFC 2460, Internet Protocol, Version 6 (IPv6)
Specification.


7.3.08  Minimal Encapsulation within IP (RFC 2004)

See Section 7.3.27


7.3.09  Applicability Statement for IP Mobility Support (2005)

See Section 7.3.26

7.3.10  IP Router Alert Option (RFC 2113)

The problems identified are resolved in RFC 2711, IPv6 Router
Alert Option.


7.3.11  SLP (RFC 2165)

The problems have been addressed in RFC 3111, Service Location
Protocol Modifications for IPv6.

Mickles & Nesser        Expires - Dec. 2003                  [Page 46]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


7.3.12  Classical IP & ARP over ATM (RFC 2225)

The problems have been resolved in RFC 2492, IPv6 over ATM
Networks.


7.3.13  IP Broadcast over ATM (RFC 2226)

The problems have been resolved in RFC 2492, IPv6 over ATM
Networks.


7.3.14  IGMPv2 (RFC 2236)

The problems have been resolved in RFC 2710, Multicast Listener
Discovery (MLD) for IPv6.


7.3.15  DHCP Options for NDS (RFC 2241)

The problems are being fixed by the work of the DHC WG.  Several very
advanced IDs address all the issues.


7.3.16  Netware/IP Domain Name and Information (RFC 2242)

The problems are being fixed by the work of the DHC WG.  Several very
advanced IDs address all the issues.


7.3.17  Mobile IPv4 Comfit Options for PPP IPCP (RFC 2290)

The problems are not being addressed and must be addressed in a new
protocol.

7.3.18  Transaction IP v3 (RFC 2371)

The problems identified are not addressed and a new standard MAY
be defined.

7.3.19  DHCP Option for Open Group User Authentication Protocol
        (RFC 2485)

The problems are being fixed by the work of the DHC WG.  Several very
advanced IDs address all the issues.

7.3.20  DHCP Option to Disable Stateless Autoconfiguration
        (RFC 2563)

Mickles & Nesser        Expires - Dec. 2003                  [Page 47]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003

The problems are being fixed by the work of the DHC WG.  Several very
advanced IDs address all the issues.


7.3.21  Non-Terminal DNS Redirection (RFC 2672)

The problems have not been addressed and a new specification MAY
be defined.


7.3.22  Binary Labels in DNS (RFC 2673)

The problems have not been addressed and a new specification MAY
be defined.


7.3.23  IP over Vertical Blanking Interval of a TV Signal (RFC 2728)

The problems have not been addressed and a new specification MAY
be defined.


7.3.24  IPv4 over IEEE 1394 (RFC 2734)

This problem is being addressed by the IPv6 WG and an ID exists
(draft-ietf-ipngwg-ipngwg-1394-02.txt).


7.3.25  Mobile IP Network Access Identity Extensions for IPv4
        (RFC 2794)

The problems are not being addressed and must be addressed in a new
protocol.


7.3.26  ARP & IP Broadcasts Over HIPPI 800 (RFC 2834)

The problems are not being addressed and MAY be addressed in a new
protocol.


7.3.27  ARP & IP Broadcasts Over HIPPI 6400 (RFC 2835)

The problems are not being addressed and MAY be addressed in a new
protocol.


7.3.28  DHCP for IEEE 1394 (RFC 2855)

This problem is being dually addressed by the IPv6 and DHC WGs and IDs
exists that address this issue.

Mickles & Nesser        Expires - Dec. 2003                  [Page 48]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


7.3.29  DHCP Name Server Search Option (RFC 2937)

The problem is being fixed by the work of the DHC WG.  Several very
advanced IDs address all the issues.


7.3.30  DHCP User Class Option (RFC 3004)

The problem is being fixed by the work of the DHC WG.  Several very
advanced IDs address all the issues.


7.3.31  IPv4 Subnet Selection DHCP Option (RFC 3011)

The problem is being fixed by the work of the DHC WG.  Several very
advanced IDs address all the issues.


7.3.32  Using 31-Bit Prefixes for IPv4 P2P Links (RFC 3021)

No action is needed.


7.3.33  Reverse Tunneling for Mobile IP (RFC 3024)

The problems are not being addressed and must be addressed in a new
protocol.


7.3.34  DHCP Relay Agent Information Option (RFC 3046)

The problem is being fixed by the work of the DHC WG.  Several very
advanced IDs address all the issues.


7.3.35  Mobile IP Vender/Organization Specific Extensions (RFC 3115)

The problems are not being addressed and must be addressed in a new
protocol.



7.4  Experimental RFCs


7.4.1  Traceroute using an IP Option (RFC 1393)

This protocol relies on IPv4 and a new protocol standard MAY be
produced.

Mickles & Nesser        Expires - Dec. 2003                  [Page 49]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


7.4.2  NBMA ARP (RFC 1735)

This functionality has been defined in RFC 2491, IPv6 over
Non-Broadcast Multiple Access (NBMA) networks and RFC 2332, NBMA
Next Hop Resolution Protocol.


7.4.3  ST2+ Protocol (RFC 1819)

This protocol relies on IPv4 and a new protocol standard MAY be
produced.


7.4.4  ARP Extensions (RFC 1868)

This protocol relies on IPv4 and a new protocol standard MAY be
produced.


7.4.5  IP Over SCSI (RFC 2143)

This protocol relies on IPv4 and a new protocol standard MAY be
produced.


Mickles & Nesser        Expires - Dec. 2003                  [Page 50]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003

8.0 Security Considerations

  This memo examines the IPv6-readiness of specifications; this does
   not have security considerations in itself.

9.0 References

9.1 Normative

[1] [Survey of IPv4 Addresses in Currently Deployed IETF Standards]
    Philip J. Nesser II, Andreas Bergstrom. "Introduction to the
    Survey ", draft-ietf-v6ops-ipv4survey-intro-01.txt
    IETF work in progress, June 2003


[2] [Survey of IPv4 Addresses in Currently Deployed IETF Standards]
    Philip J. Nesser II, Andreas Bergstrom: " IETF Sub-IP Area
    Standards ", draft-ietf-v6ops- ipv4survey-subip-01.txt,
    IETF work in progress. June 2003,

10.0 Acknowledgements

The author would like to acknowledge the support of the Internet
Society in the research and production of this document.
Additionally the author would like to thanks his partner in all
ways, Wendy M. Nesser.

The editor, Cleveland Mickles, would like to thank Steve Bellovin
and Russ Housley for their comments and Pekka Savola for his comments
and guidance during the editing of this document.  Additionally the
editor would like to thank, his wife, Lesia R. Mickles for her patient
support.













Mickles & Nesser        Expires - Dec. 2003                  [Page 51]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003


11.0 Author's Addresses

Please contact the authors with any questions, comments or suggestions
at:

Cleveland Mickles  (Primary Editor)
America Online, Inc (owned by AOL Time Warner)
12100 Sunrise Valley Drive.          Phone:  +1 703-265-5618
Reston, VA 20191, USA                Email:  micklesc@aol.net

Philip J. Nesser II (Author)
Principal
Nesser & Nesser Consulting
13501 100th Ave NE, #5202               Phone:  +1 425 481 4303
Kirkland, WA 98034                      Email:  phil@nesser.com
Fax:    +1 425 48


12.0 Intellectual Property Statement

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; neither does it represent that it
   has made any effort to identify any such rights. Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11. Copies of
   claims of rights made available for publication and any assurances
   of licenses to be made available, or the result of an attempt made
   to obtain a general license or permission for the use of such
   proprietary rights by implementors or users of this specification
   can be obtained from the IETF Secretariat.
   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard. Please address the information to the IETF Executive
   Director.

Mickles & Nesser        Expires - Dec. 2003                  [Page 52]

 Internet Area: Survey of IPv4 Addresses Currently Deployed  Mar. 2003

13.0  Full Copyright Statement

   Copyright (C) The Internet Society (2000).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph
   are included on all such copies and derivative works. However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of develop-
   ing Internet standards in which case the procedures for copyrights
   defined in the Internet Standards process must be followed, or as
   required to translate it into languages other than English. The lim-
   ited permissions granted above are perpetual and will not be revoked
   by the Internet Society or its successors or assigns. This document
   and the information contained herein is provided on an "AS IS" basis
   and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DIS-
   CLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
   TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT
   INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
   FITNESS FOR A PARTICULAR PURPOSE.

























Mickles & Nesser        Expires - Dec. 2003                  [Page 53]


Html markup produced by rfcmarkup 1.109, available from https://tools.ietf.org/tools/rfcmarkup/