[Docs] [txt|pdf|xml|html] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits] [IPR]

Versions: (draft-vandevelde-v6ops-ra-guard) 00 01 02 03 04 05 06 07 08 RFC 6105

v6ops Working Group                                     E. Levy-Abegnoli
Internet-Draft                                           G. Van de Velde
Intended status: Informational                              C. Popoviciu
Expires: March 6, 2011                                     Cisco Systems
                                                              J. Mohacsi
                                                          NIIF/Hungarnet
                                                      September 02, 2010


                    IPv6 Router Advertisement Guard
                   <draft-ietf-v6ops-ra-guard-07.txt>

Abstract

   When using IPv6 within a single L2 network segment it is possible and
   sometimes desirable to enable layer 2 devices to drop rogue RAs
   before they reach end-nodes.  In order to distinguish valid from
   rogue RAs, the L2 devices can use a spectrum of criteria, from a
   static scheme that blocks RAs received on un-trusted ports, or from
   un-trusted sources, to a more dynamic scheme that uses Secure
   Neighbor Discovery (SEND) to challenge RA sources.

   This document reviews various techniques applicable on the L2 devices
   to reduce the threat of rogue RAs.

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on March 6, 2011.

Copyright Notice

   Copyright (c) 2010 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal



Levy-Abegnoli, et al.     Expires March 6, 2011                 [Page 1]

Internet-Draft                IPv6 RA-Guard               September 2010


   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

   This document may contain material from IETF Documents or IETF
   Contributions published or made publicly available before November
   10, 2008.  The person(s) controlling the copyright in some of this
   material may not have granted the IETF Trust the right to allow
   modifications of such material outside the IETF Standards Process.
   Without obtaining an adequate license from the person(s) controlling
   the copyright in such materials, this document may not be modified
   outside the IETF Standards Process, and derivative works of it may
   not be created outside the IETF Standards Process, except to format
   it for publication as an RFC or to translate it into languages other
   than English.































Levy-Abegnoli, et al.     Expires March 6, 2011                 [Page 2]

Internet-Draft                IPv6 RA-Guard               September 2010


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  4
   2.  Model and Applicability  . . . . . . . . . . . . . . . . . . .  4
   3.  Stateless RA-Guard . . . . . . . . . . . . . . . . . . . . . .  6
   4.  Stateful RA-Guard  . . . . . . . . . . . . . . . . . . . . . .  6
     4.1.  State Machine  . . . . . . . . . . . . . . . . . . . . . .  7
     4.2.  SEND-based RA-Guard  . . . . . . . . . . . . . . . . . . .  8
   5.  RA-Guard Use Considerations  . . . . . . . . . . . . . . . . .  9
   6.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . .  9
   7.  Security Considerations  . . . . . . . . . . . . . . . . . . .  9
   8.  Acknowledgements . . . . . . . . . . . . . . . . . . . . . . .  9
   9.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 10
     9.1.  Normative References . . . . . . . . . . . . . . . . . . . 10
     9.2.  Informative References . . . . . . . . . . . . . . . . . . 10
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 10



































Levy-Abegnoli, et al.     Expires March 6, 2011                 [Page 3]

Internet-Draft                IPv6 RA-Guard               September 2010


1.  Introduction

   When operating IPv6 in a shared L2 network segment without complete
   SEND support by all devices connected or without the availability of
   the infrastructure necessary to support Secure Neighbor Discovery
   (SEND) [RFC3971], there is always the risk of facing operational
   problems due to rogue Router Advertisements generated maliciously or
   unintentionally by unauthorized or improperly configured routers
   connecting to the segment.

   There are several examples of work done on this topic which resulted
   in several related studies [reference1] [reference2]
   [reference3].This document describes a solution framework for the
   rogue-RA problem where network segments are designed around a single
   or a set of L2-switching devices capable of identifying invalid RAs
   and blocking them.  The solutions developed within this framework can
   span the spectrum from basic (where the port of the L2 device is
   statically instructed to forward or not to forward RAs received from
   the connected device) to advanced (where a criteria is used by the L2
   device to dynamically validate or invalidate a received RA, this
   criteria can even be based on SEND mechanisms).


2.  Model and Applicability

   RA-Guard applies to an environment where all messages between IPv6
   end-devices traverse the controlled L2 networking devices.  It does
   not apply to a shared media such as an Ethernet hub, when devices can
   communicate directly without going through an RA-Guard capable L2
   networking device.

   Figure 1 illustrates a deployment scenario for RA-Guard.



















Levy-Abegnoli, et al.     Expires March 6, 2011                 [Page 4]

Internet-Draft                IPv6 RA-Guard               September 2010


                     Block                Allow
      +------+       incoming +---------+ incoming     +--------+
      |Host  |       RA       |    L2   | RA           | Router |
      |      |----------------|  device |--------------|        |
      +------+                +----+----+              +--------+
                                   |
                                   |Block
                                   |incoming
                                   |RA
                                   |
                                   |
                                   |
                               +---+---+
                               |  Host |
                               |       |
                               +-------+

   Figure 1

   RA-Guard does not intend to provide a substitute for SEND based
   solutions.  It actually intends to provide complementary solutions in
   those environments where SEND might not be suitable or fully
   supported by all devices involved.  It may take time until SEND is
   ubiquitous in IPv6 networks and some of its large scale deployment
   aspects are sorted out such as provisioning hosts with trust anchors.
   It is also reasonable to expect that some devices might not consider
   implementing SEND at all such as IPv6 enabled sensors.  An RA-Guard
   implementation which SEND-validates RAs on behalf of hosts would
   potentially simplify some of these challenges.

   RA-Guard can be seen as a superset of SEND with regard to router
   authorization.  Its purpose is to filter Router Advertisements based
   on a set of criteria, from a simplistic "RA disallowed on a given
   interface" to "RA allowed from pre-defined sources" and up to full
   fledge SEND "RA allowed from authorized sources only".

   In addition to this granularity on the criteria for filtering out
   Router Advertisements, RA-Guard introduces the concept of router
   authorization proxy.  Instead of each node on the link analyzing RAs
   and making an individual decision, a legitimate node-in-the-middle
   performs the analysis on behalf of all other nodes on the link.  The
   analysis itself is not different from what each node would do: if
   SEND is enabled, the RA is checked against X.509 certificates
   [RFC4861].  If any other criteria is in use, such as known L3
   (addresses) or L2 (link-layer address, port number) legitimate
   sources of RAs, the node-in-the middle can use this criteria and
   filter out any RA that does not comply.  If this node-in-the-middle
   is a L2 device, it will not change the content of the validated RA,



Levy-Abegnoli, et al.     Expires March 6, 2011                 [Page 5]

Internet-Draft                IPv6 RA-Guard               September 2010


   and avoid any of the ND-proxy pitfalls.

   RA-Guard intends to provide simple solutions to the rogue-RA problem
   in contexts where simplicity is required while leveraging SEND in an
   context environment consisting of with a mix of SEND capable devices
   (L2 switches and routers) and devices that do not consistently use
   SEND.  Furthermore, RA-Guard is useful to simplify SEND deployments,
   as only the L2 switch and the routers are required to carry
   certificates (their own and the trust anchor certificates).


3.  Stateless RA-Guard

   Stateless RA-Guard examines incoming RAs and decide whether to
   forward or block them based solely on information found in the
   message or in the L2-device configuration.  Typical information
   available in the frames received, useful for RA validation is:

   o  Link-layer address of the sender
   o  Port on which the frame was received
   o  IP source address
   o  Prefix list

   The following configuration information created on the L2-device can
   be made available to RA-Guard, to validate against the information
   found in the received RA frame:

   o  Allowed/Disallowed link-layer address of RA-sender
   o  Allowed/Disallowed ports for receiving RAs
   o  Allowed/Disallowed IP source addresses of RA-sender
   o  Allowed Prefix list and Prefix ranges
   o  Router Priority

   Once the L2 device has validated the content of the RA frame against
   the configuration, it forwards the RA to destination, whether unicast
   or multicast.  Otherwise, the RA is dropped.

   An example of a very simple stateless RA-Guard implementation could
   be a small L2-switch for which there is one interface "statically-
   configured" as the interface connecting to a router, while all other
   interfaces are for non-router devices.  With his small static setup
   the only interface forwarding RAs will be the pre-assigned router
   interface, while the non-router interfaces block all RAs.


4.  Stateful RA-Guard





Levy-Abegnoli, et al.     Expires March 6, 2011                 [Page 6]

Internet-Draft                IPv6 RA-Guard               September 2010


4.1.  State Machine

   Stateful RA-Guard learns dynamically about legitimate RA senders, and
   store this information for allowing subsequent RAs.  A simple
   stateful scheme would be for the L2-device to listen to RAs during a
   certain manual determined period of time, where the start of the
   listening-period and the duration of the listening-period for a
   single instance is controled by the manual intervention.  As result
   the L2-device can then allow subsequent RAs only on those ports on
   which valid RAs were received during this period.  Often the LEARNING
   state will only be activated by manual configuration when a new IPv6
   router is provisioned on the L2-network.

   A more sophisticated stateful scheme is based on SEND, and is
   described in Section 4.2.

   The state machine for stateful RA-Guard can be global, per-interface,
   or per-peer, depending on the scheme used for authorizing RAs.

   When RA-Guard is SEND-based, the state machine is per-peer and
   defined in [RFC3971].

   When RA-Guard is using a discovery method, the state-machine of the
   RA-Guard capability consists of four different states:

   o  State 1: OFF
         A device or interface in RA-Guard "OFF" state, operates as if
         the RA-Guard capability is not available.
   o  State 2: LEARNING
         A device or interface in the RA-Guard "Learning" state is
         actively acquiring information about the IPv6 routing devices
         connected.  The learning process takes place over a pre-defined
         unique period in time, set by manual configuration or it can be
         event triggered.  The information gathered is compared against
         pre-defined criteria; criteria similar as the stateless RA-
         Guard rules to qualify the validity of the RAs.
         In this state, the RA-Guard enabled device or interface is
         either blocking "all" RAs until their validity is verified or,
         alternatively it can temporarily forward "all" the RAs until
         their validity is verified.
         Once the L2-device has identified through "Learning" the valid
         IPv6 routers and hence also identified the valid RAs, it
         transtions each interface from "LEARNING" into either BLOCKING
         state if there was no valid IPv6 router discovered at the
         interface, or transitions the interface into FORWARDING state
         if there was a valid IPv6 router discovered.





Levy-Abegnoli, et al.     Expires March 6, 2011                 [Page 7]

Internet-Draft                IPv6 RA-Guard               September 2010


   o  State 3: BLOCKING
         A device or interface running RA-Guard and in Blocking state
         will block ingress RA-messages.
         An interface can transition from BLOCKING state into FORWARDING
         state directly if explicitly instructed by the L2-device
         operator.
         An interface can transition from BLOCKING state into LEARNING
         state if either explicitly told by the L2-device operator or by
         a triggered event.
   o  State 4: FORWARDING
         A device or interface running RA-Guard and in Forwarding state
         will accept valid ingress RAs and forward them to their
         destination.
         An interface can transition from FORWARDING state into BLOCKING
         state directly if explicitly instructed by the L2-device
         operator.
         An interface can transition from FORWARDING state into LEARNING
         state if either explicitly told by the L2-device operator or by
         a triggered event.

   The transition between these states can be triggered by manual
   configuration or by meeting a pre-defined criteria.

4.2.  SEND-based RA-Guard

   In this scenario, the L2 device is blocking or forwarding RAs based
   on SEND considerations.  Upon capturing an RA on the interface, the
   L2-device will first verify the Cryptographically Generated Addresses
   (CGA) [RFC3971] address and the RSA (Rivest, Shamir and Adleman
   algorithm for public-key cryptography) signature, as specified in
   section 5 of [RFC3971].  RA should be dropped in case of failure of
   this verification.  It will then apply host behavior as described in
   section 6.4.6 of [RFC3971].  In particular, the L2 device will
   attempt to retrieve a valid certificate from its cache for the public
   key referred to in the RA.  If such certificate is found, the L2
   device will forward the RA to destination.  If not, the L2 device
   will generate a Certification Path Solicitation (CPS) [RFC3971],
   sourced with UNSPECIFIED address, to query the router certificate(s).
   It will then capture the Certification Path Advertisements (CPA)
   [RFC3971], and attempt to validate the certificate chain.  Failure to
   validate the chain will result in dropping the RA.  Upon validation
   success, the L2 device will forward the RA to destination and and
   store the router certificate in its cache.

   In order to operate in this scenario, the L2-device should be
   provisioned with a trust anchor certificate, as specified in section
   6 of [RFC3971].  It may also establish a layer-3 connectivity with a
   Certificate Revocation List (CRL) Certification Path Advertisement



Levy-Abegnoli, et al.     Expires March 6, 2011                 [Page 8]

Internet-Draft                IPv6 RA-Guard               September 2010


   server and/or with and NTP server.  Bootstrapping issue in this case
   can be resolved by using the configuration method to specify a
   trusted port to a first router, and SEND-based RA-Guard method on all
   other ports.  The first router can then be used for Network Time
   Protocol (NTP) [RFC5905] and CRL connectivity.


5.  RA-Guard Use Considerations

   The RA-Guard mechanism is effective only when all messages between
   IPv6 devices in the target environment traverse controlled L2
   networking devices.  In the case of environments such as Ethernet
   hubs, devices can communicate directly without going through an RA-
   Guard capable L2 networking device, the RA-Guard feature cannot
   protect against rogue-RAs.

   RA-Guard mechanisms do not offer protection in environments where
   IPv6 traffic is tunneled.


6.  IANA Considerations

   There are no extra IANA consideration for this document.


7.  Security Considerations

   Once RA-Guard has setup the proper criteria, for example, it
   identified that a port is allowed to receive RAs, or it identified
   legitimate sources of RA, or certificate base [RFC4861], then there
   is no possible instances of accidently filtered legitimate Router
   advertisements assuming the RA-Guard filter enforcement follows
   strictly the RA-Guard set criteria.

   in Section 4.1 a simple mechanism to learn dynamical the valid IPv6
   routers connected to a L2-device is explained.  It is important that
   this LEARN state is only entered intentionally by manual
   configuration.  The list of learned IPv6 routers should be verified
   by the network manager to make sure that it corresponds with the
   expected valid RA list.  This procedure will make sure that either
   accidently or intentionally rogue RAs are blocked by RA-guard.


8.  Acknowledgements

   The authors dedicate this document to the memory of Jun-ichiro Hagino
   (itojun) for his contributions to the development and deployment of
   IPv6.



Levy-Abegnoli, et al.     Expires March 6, 2011                 [Page 9]

Internet-Draft                IPv6 RA-Guard               September 2010


9.  References

9.1.  Normative References

   [RFC3971]  Arkko, J., Kempf, J., Zill, B., and P. Nikander, "SEcure
              Neighbor Discovery (SEND)", RFC 3971, March 2005.

   [RFC4861]  Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
              "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
              September 2007.

   [RFC4158]  Cooper, M., Dzambasow, Y., Hesse, P., Joseph, S., and R.
              Nicholas, "Internet X.509 Public Key Infrastructure:
              Certification Path Building", RFC 4158, September 2005.

   [RFC5905]  Mills, D., Martin, J., Burbank, J., and W. Kasch, "Network
              Time Protocol Version 4: Protocol and Algorithms
              Specification", RFC 5905, June 2010.

9.2.  Informative References

   [reference1]
              LORIA/INRIA, "NDPMon - IPv6 Neighbor Discovery Protocol
              Monitor (http://ndpmon.sourceforge.net/)", November 2007.

   [reference2]
              KAME Project, "rafixd - developed at KAME - An active
              rogue RA nullifier (http://www.kame.net/dev/cvsweb2.cgi/
              kame/kame/kame/rafixd/)", November 2007.

   [reference3]
              Hagino (itojun), Jun-ichiro., "Discussion of the various
              solutions (http://ipv6samurais.com/ipv6samurais/
              demystified/rogue-RA.html)", 2007.

   [reference4]
              Chown, Tim. and Stig. Venaas, "Rogue IPv6 Router
              Advertisement Problem (draft-ietf-v6ops-rogue-ra-00.txt)",
              May 2009.












Levy-Abegnoli, et al.     Expires March 6, 2011                [Page 10]

Internet-Draft                IPv6 RA-Guard               September 2010


Authors' Addresses

   Eric Levy Abegnoli
   Cisco Systems
   Village d'Entreprises Green Side - 400, Avenue Roumanille
   Biot - Sophia Antipolis, PROVENCE-ALPES-COTE D'AZUR  06410
   France

   Phone: +33 49 723 2620
   Email: elevyabe@cisco.com


   Gunter Van de Velde
   Cisco Systems
   De Kleetlaan 6a
   Diegem  1831
   Belgium

   Phone: +32 2704 5473
   Email: gunter@cisco.com


   Ciprian Popoviciu
   Cisco Systems
   7025-6 Kit Creek Road
   Research Triangle Park, North Carolina  NC 27709-4987
   USA

   Phone: +1 919 392-3723
   Email: cpopovic@cisco.com


   Janos Mohacsi
   NIIF/Hungarnet
   18-22 Victor Hugo
   Budapest  H-1132
   Hungary

   Phone: tbc
   Email: mohacsi@niif.hu











Levy-Abegnoli, et al.     Expires March 6, 2011                [Page 11]


Html markup produced by rfcmarkup 1.109, available from https://tools.ietf.org/tools/rfcmarkup/