[Docs] [txt|pdf|xml] [Tracker] [WG] [Email] [Nits]

Versions: 00 01 02 03 04 05 06 07 10 11 12 13 14 RFC 7005

Audio/Video Transport Working Group                              G. Hunt
Internet-Draft                                              Unaffiliated
Intended status: Standards Track                                A. Clark
Expires: November 10, 2012                                      Telchemy
                                                                V. Singh
                                                        Aalto University
                                                                   Q. Wu
                                                                  Huawei
                                                             May 9, 2012


        RTCP XR Report Block for Jitter Buffer Metric Reporting
                  draft-ietf-xrblock-rtcp-xr-jb-00.txt

Abstract

   This document defines an RTCP XR Report Block that allows the
   reporting of Jitter Buffer metrics for a range of RTP applications.

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on November 10, 2012.

Copyright Notice

   Copyright (c) 2012 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of



Hunt, et al.            Expires November 10, 2012               [Page 1]

Internet-Draft            RTCP XR Jitter Buffer                 May 2012


   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
     1.1.  Jitter Buffer Metrics Block  . . . . . . . . . . . . . . .  3
     1.2.  RTCP and RTCP XR Reports . . . . . . . . . . . . . . . . .  3
     1.3.  Performance Metrics Framework  . . . . . . . . . . . . . .  3
     1.4.  Applicability  . . . . . . . . . . . . . . . . . . . . . .  3
   2.  Jitter Buffer Metrics Block  . . . . . . . . . . . . . . . . .  4
     2.1.  Report Block Structure . . . . . . . . . . . . . . . . . .  4
     2.2.  Definition of Fields in Jitter Buffer Metrics Block  . . .  4
   3.  SDP Signaling  . . . . . . . . . . . . . . . . . . . . . . . .  7
   4.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . .  8
     4.1.  New RTCP XR Block Type value . . . . . . . . . . . . . . .  8
     4.2.  New RTCP XR SDP Parameter  . . . . . . . . . . . . . . . .  8
     4.3.  Contact information for registrations  . . . . . . . . . .  8
   5.  Security Considerations  . . . . . . . . . . . . . . . . . . .  9
   6.  Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . . 10
   7.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 11
     7.1.  Normative References . . . . . . . . . . . . . . . . . . . 11
     7.2.  Informative References . . . . . . . . . . . . . . . . . . 11
   Appendix A.  Change Log  . . . . . . . . . . . . . . . . . . . . . 12
     A.1.  draft-ietf-xrblock-rtcp-xr-jb-00 . . . . . . . . . . . . . 12
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 13
























Hunt, et al.            Expires November 10, 2012               [Page 2]

Internet-Draft            RTCP XR Jitter Buffer                 May 2012


1.  Introduction

1.1.  Jitter Buffer Metrics Block

   This draft defines a new block type to augment those defined in
   [RFC3611], for use in a range of RTP applications.

   The new block type provides information on jitter buffer
   configuration and performance.

   The metric belongs to the class of transport-related terminal metrics
   defined in [MONARCH] (work in progress).

   Instances of this Metrics Block refer by SSRC to the separate
   auxiliary Measurement Information block [MEASI] which contains
   information such as the SSRC of the measured stream, and RTP sequence
   numbers and time intervals indicating the span of the report.

1.2.  RTCP and RTCP XR Reports

   The use of RTCP for reporting is defined in [RFC3550].  [RFC3611]
   defined an extensible structure for reporting using an RTCP Extended
   Report (XR).  This draft defines a new Extended Report block that
   MUST be used as defined in [RFC3550] and [RFC3611].

1.3.  Performance Metrics Framework

   The Performance Metrics Framework [RFC6390] provides guidance on the
   definition and specification of performance metrics.  The RTP
   Monitoring Architectures [MONARCH] provides guideline for reporting
   block format using RTCP XR.  Metrics described in this draft are in
   accordance with the guidelines in [RFC6390][MONARCH].

1.4.  Applicability

   These metrics are applicable to a range of RTP applications.















Hunt, et al.            Expires November 10, 2012               [Page 3]

Internet-Draft            RTCP XR Jitter Buffer                 May 2012


2.  Jitter Buffer Metrics Block

   This block describes the configuration and operating parameters of
   the jitter buffer in the receiver of the RTP end system or RTP mixer
   which sends the report.  Instances of this Metrics Block refer by
   SSRC to the separate auxiliary Measurement Information block [MEASI]
   which contains measurement intervals.  This metric block relies on
   the measurement interval in the Measurement Information block
   indicating the span of the report and should be sent in the same
   compound RTCP packet as the measurement information block.  If the
   measurement interval is not received in the same compound RTCP packet
   as this metric block, this metric block should be discarded.

2.1.  Report Block Structure

   JB Metrics Block

        0               1               2               3
        0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |     BT=NJB    | I |jb cfg |rsv|       block length=3          |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                           SSRC of Source                      |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |          JB nominal           |         JB maximum            |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |     JB high water mark        |      JB low water mark        |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                     Figure 1: Report Block Structure

2.2.  Definition of Fields in Jitter Buffer Metrics Block

   Block type (BT): 8 bits

      A Jitter Buffer Metrics Report Block is identified by the constant
      NJB.

      [Note to RFC Editor: please replace NJB with the IANA provided
      RTCP XR block type for this block.]


   Interval Metric flag (I): 2 bits

      This field is used to indicate whether the Jitter Buffer metrics
      are Sampled, Interval or Cumulative metrics, that is, whether the
      reported values applies to the most recent measurement interval
      duration between successive metrics reports (I=10) (the Interval



Hunt, et al.            Expires November 10, 2012               [Page 4]

Internet-Draft            RTCP XR Jitter Buffer                 May 2012


      Duration) or to the accumulation period characteristic of
      cumulative measurements (I=11) (the Cumulative Duration) or is a
      sampled instantaneous value (I=01) (Sampled Value).


   Jitter Buffer Configuration (jb cfg): 4 bits

      This field is used to identify the jitter buffer method in use at
      the receiver, according to the following code:

         bits 014-011

            0 = Fixed jitter buffer

            1 = Adaptive jitter buffer

            Other values reserved


   Reserved (resv): 2 bits

      These bits are reserved.  They SHOULD be set to zero by senders
      and MUST be ignored by receivers.


   block length: 16 bits

      The length of this report block in 32-bit words, minus one.  For
      the Delay block, the block length is equal to 3.


   jitter buffer nominal delay (JB nominal): 16 bits

      This is the current nominal jitter buffer delay in milliseconds,
      which corresponds to the nominal jitter buffer delay for packets
      that arrive exactly on time.  This parameter MUST be provided for
      both fixed and adaptive jitter buffer implementations.

      If the measured value exceeds 0xFFFD, the value 0xFFFE SHOULD be
      reported to indicate an over-range measurement.  If the
      measurement is unavailable, the value 0xFFFF SHOULD be reported.


   jitter buffer maximum delay (JB maximum): 16 bits

      This is the current maximum jitter buffer delay in milliseconds
      which corresponds to the earliest arriving packet that would not
      be discarded.  In simple queue implementations this may correspond



Hunt, et al.            Expires November 10, 2012               [Page 5]

Internet-Draft            RTCP XR Jitter Buffer                 May 2012


      to the nominal size.  In adaptive jitter buffer implementations,
      this value may dynamically.  This parameter MUST be provided for
      both fixed and adaptive jitter buffer implementations.

      If the measured value exceeds 0xFFFD, the value 0xFFFE SHOULD be
      reported to indicate an over-range measurement.  If the
      measurement is unavailable, the value 0xFFFF SHOULD be reported.


   jitter buffer high water mark (JB high water mark): 16 bits

      This is the highest value of the jitter buffer nominal delay which
      occurred at any time during the reporting interval.

      If the measured value exceeds 0xFFFD, the value 0xFFFE SHOULD be
      reported to indicate an over-range measurement.  If the
      measurement is unavailable, the value 0xFFFF SHOULD be reported.


   jitter buffer low water mark (JB low water mark): 16 bits

      This is the lowest value of the jitter buffer nominal delay which
      occurred at any time during the reporting interval.

      If the measured value exceeds 0xFFFD, the value 0xFFFE SHOULD be
      reported to indicate an over-range measurement.  If the
      measurement is unavailable, the value 0xFFFF SHOULD be reported.
























Hunt, et al.            Expires November 10, 2012               [Page 6]

Internet-Draft            RTCP XR Jitter Buffer                 May 2012


3.  SDP Signaling

   [RFC3611] defines the use of SDP (Session Description Protocol)
   [RFC4566] for signaling the use of XR blocks.  XR blocks MAY be used
   without prior signaling.

   This section augments the SDP [RFC4566] attribute "rtcp-xr" defined
   in [RFC3611] by providing an additional value of "xr-format" to
   signal the use of the report block defined in this document.

   rtcp-xr-attrib = "a=" "rtcp-xr" ":" [xr-format *(SP xr-format)] CRLF

   (defined in [RFC3611])

   xr-format =/ xr-jb-block

   xr-jb-block = "jitter-bfr"


































Hunt, et al.            Expires November 10, 2012               [Page 7]

Internet-Draft            RTCP XR Jitter Buffer                 May 2012


4.  IANA Considerations

   New block types for RTCP XR are subject to IANA registration.  For
   general guidelines on IANA considerations for RTCP XR, refer to
   [RFC3611].

4.1.  New RTCP XR Block Type value

   This document assigns the block type value NJB in the IANA "RTCP XR
   Block Type Registry" to the "JB Metrics Block".

   [Note to RFC Editor: please replace NJB with the IANA provided RTCP
   XR block type for this block.]

4.2.  New RTCP XR SDP Parameter

   This document also registers a new parameter "jitter-bfr" in the
   "RTCP XR SDP Parameters Registry".

4.3.  Contact information for registrations


   The contact information for the registrations is:

   Geoff Hunt (r.geoff.hunt@gmail.com)

   Orion 2 PP3, Adastral Park, Martlesham Heath, Ipswich IP5 3RE, United
   Kingdom























Hunt, et al.            Expires November 10, 2012               [Page 8]

Internet-Draft            RTCP XR Jitter Buffer                 May 2012


5.  Security Considerations

   It is believed that this proposed RTCP XR report block introduces no
   new security considerations beyond those described in [RFC3611].
   This block does not provide per-packet statistics so the risk to
   confidentiality documented in Section 7, paragraph 3 of [RFC3611]
   does not apply.












































Hunt, et al.            Expires November 10, 2012               [Page 9]

Internet-Draft            RTCP XR Jitter Buffer                 May 2012


6.  Acknowledgments

   The authors gratefully acknowledge the comments and contributions
   made by Bruce Adams, Philip Arden, Amit Arora, Bob Biskner, Kevin
   Connor, Claus Dahm, Randy Ethier, Roni Even, Jim Frauenthal, Albert
   Higashi, Tom Hock, Shane Holthaus, Paul Jones, Rajesh Kumar, Keith
   Lantz, Mohamed Mostafa, Amy Pendleton, Colin Perkins, Mike Ramalho,
   Ravi Raviraj, Albrecht Schwarz, Tom Taylor, and Hideaki Yamada.











































Hunt, et al.            Expires November 10, 2012              [Page 10]

Internet-Draft            RTCP XR Jitter Buffer                 May 2012


7.  References

7.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", March 1997.

   [RFC3550]  Schulzrinne, H., "RTP: A Transport Protocol for Real-Time
              Applications", RFC 3550, July 2003.

   [RFC3611]  Friedman, T., Caceres, R., and A. Clark, "RTP Control
              Protocol Extended Reports (RTCP XR)", November 2003.

   [RFC4566]  Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
              Description Protocol", July 2006.

7.2.  Informative References

   [MEASI]    Hunt, G., "Measurement Identity and information Reporting
              using SDES item and XR Block",
              ID draft-ietf-xrblock-rtcp-xr-meas-identity-06,
              April 2012.

   [MONARCH]  Hunt, G., "Monitoring Architectures for RTP",
              ID draft-ietf-avtcore-monarch-12, April 2012.

   [RFC6390]  Clark, A. and B. Claise, "Framework for Performance Metric
              Development", RFC 6390, October 2011.























Hunt, et al.            Expires November 10, 2012              [Page 11]

Internet-Draft            RTCP XR Jitter Buffer                 May 2012


Appendix A.  Change Log

   Note to the RFC-Editor: please remove this section prior to
   publication as an RFC.

A.1.  draft-ietf-xrblock-rtcp-xr-jb-00

   The following are the major changes to previous version :

   o  Boilerplate updates.

   o  references updates

   o  allocate 32 bit field in report block for SSRC

   o  Other editorial changes to get alignment with MONARCH draft.



































Hunt, et al.            Expires November 10, 2012              [Page 12]

Internet-Draft            RTCP XR Jitter Buffer                 May 2012


Authors' Addresses

   Geoff Hunt
   Unaffiliated

   Email: r.geoff.hunt@gmail.com


   Alan Clark
   Telchemy Incorporated
   2905 Premiere Parkway, Suite 280
   Duluth, GA  30097
   USA

   Email: alan.d.clark@telchemy.com


   Varun Singh
   Aalto University
   Otakaari 5 A
   Espoo  FIN 02150
   Finland

   Email: vsingh.ietf@gmail.com


   Qin Wu
   Huawei
   101 Software Avenue, Yuhua District
   Nanjing, Jiangsu  210012
   China

   Email: sunseawq@huawei.com


















Hunt, et al.            Expires November 10, 2012              [Page 13]


Html markup produced by rfcmarkup 1.107, available from http://tools.ietf.org/tools/rfcmarkup/