[Docs] [txt|pdf] [Tracker] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 04 05 RFC 4967

iptel                                                           B. Rosen
Internet-Draft                                                   NeuStar
Intended status: Standards Track                        October 20, 2006
Expires: April 23, 2007


    Dialstring parameter for the Session Initiation Protocol Uniform
                          Resource Identifier
                  draft-rosen-iptel-dialstring-05.txt

Status of this Memo

   By submitting this Internet-Draft, each author represents that any
   applicable patent or other IPR claims of which he or she is aware
   have been or will be disclosed, and any of which he or she becomes
   aware will be disclosed, in accordance with Section 6 of BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

   This Internet-Draft will expire on April 23, 2007.

Copyright Notice

   Copyright (C) The Internet Society (2006).

Abstract

   RFC3966 explicitly states that 'tel' URIs may not represent a dial
   string.  That leaves no way specify a dial string in a standardized
   way.  Great confusion exists with the SIP URI parameter "user=phone",
   and specifically, if it can represent a dial string.  This memo
   creates a new value for the user parameter "dialstring", so that one
   may specify "user=dialstring" to encode a dial string as a 'sip:' or
   'sips:' URI.



Rosen                    Expires April 23, 2007                 [Page 1]

Internet-Draft            Dialstring Parameter              October 2006


Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . 3
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . 3
   3.  Requirements  . . . . . . . . . . . . . . . . . . . . . . . . . 4
   4.  Solution  . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
   5.  IANA Considerations . . . . . . . . . . . . . . . . . . . . . . 5
   6.  Security Considerations . . . . . . . . . . . . . . . . . . . . 5
   7.  Normative References  . . . . . . . . . . . . . . . . . . . . . 6
   Author's Address  . . . . . . . . . . . . . . . . . . . . . . . . . 6
   Intellectual Property and Copyright Statements  . . . . . . . . . . 7








































Rosen                    Expires April 23, 2007                 [Page 2]

Internet-Draft            Dialstring Parameter              October 2006


1.  Introduction

   A user at a phone often has a limited User Interface, and in some
   cases, is limited to a 10 key pad (and sometimes a "flash" function
   with the switchhook).  The user enters a series of digits that invoke
   some kind of function.  The entered sequence, called a "dial string",
   may be translated to a telephone number, or it may invoke a special
   service.  In many newer designs, the mapping between a dial string
   and a phone number or service URI is contained within the phone
   (digitmap).  However, there are many phones and terminal adapters
   that do not have internal translation mechanisms.  Without a
   translation mechanism in the phone, the phone must send the dial
   string in a 'sip:' or 'sips:' URI [RFC3261] to an intermediary that
   can transform the dial string to a phone number or a service
   invocation.  The intermediary is able to perform this transform
   provided that it knows the context (i.e., dialing plan) within which
   the number was dialed.

   There is a problem here.  The intermediary can apply its
   transformation only if it recognizes that the user part of the SIP
   URI is a dial string.  However, there is currently no way to
   distinguish an user part consisting of a dial string from an user
   part that happens to be composed of characters that would appear in a
   dial string.

   Use of DTMF detectors after the initial number has been dialed is not
   uncommon.  A common function some systems have is to express a string
   that incorporates fixed time delays, or in some cases, actual "wait
   for call completion" after which additional DTMF signals are emitted.
   For example, many voicemail systems use a common phone number, after
   which the system expects the desired mailbox number as a series of
   DTMF digits to deposit a message for.  Many gateways have the ability
   to interpret such strings, but there is no standardized way to
   express them, leading to interoperability problems between endpoints.
   This is another case where the ability to indicate that a dialstring
   is being presented would be useful.


2.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

   It is assumed that the reader is familiar with the terminology and
   acronyms defined in [RFC3261]





Rosen                    Expires April 23, 2007                 [Page 3]

Internet-Draft            Dialstring Parameter              October 2006


3.  Requirements

   A mechanism to express a dial string in a 'sip:' or 'sips:' URI is
   required.  A dial string consists of a sequence of
      * The digits 0-9
      * The special characters # and *
      * The DTMF digits A-D
      * characters representing a short Pause, and a "Wait for call
      completion" in a dial string

   Note: DTMF = Dual Tone MultiFrequency.  Each "tone:" is actually two
   frequencies superimposed.  DTMF is a 4 x 4 matrix with four row
   frequencies (697, 770, 852, 941 Hz) and four column frequencies
   (1209, 1336, 1477, 1633).  Most telephones only implement 3 of the 4
   columns, which are used just like the telephone dial pad implies they
   are.  Thus, the digit 2 is the first row, second column, and consists
   of 770Hz and 1209Hz frequencies mixed together.  The fourth column is
   not used in the PSTN.  The "digits" for the fourth column are usually
   expressed using the letters A through D. Thus, "C" is 852/1633Hz.
   Some equipment does use these digits, so we include them in the
   definition of the dial string.

   A dial string always exists within a context.  The context MUST be
   specified when expressing a dial string.

   It MUST be possible to distinguish between a dial string and an user
   part that happens to consist of the same characters.


4.  Solution

   A new alternative value for the "userinfo" parameter of the 'sip:' or
   'sips:' URI schemes is defined, "dialstring".  This value may be used
   in a 'sip:' or 'sips:' URI when the user part is a dial string.  The
   dialstring is a sequence of the characters 0-9, A-F, P, X, '*' and
   "#'.  E represents *, F represents #, P is a pause (short wait, like
   a comma in a modem string) and X represents "wait for call
   completion".

   When the "user=dialstring" is used, a context parameter as defined in
   [RFC3966] MUST be specified.  The context parameter would normally be
   a domain name.  The domain name does not have to resolve to any
   actual host but MUST be under the administrative control of the
   entity managing the local phone context.  The context parameter value
   is normally configured in the user agent.






Rosen                    Expires April 23, 2007                 [Page 4]

Internet-Draft            Dialstring Parameter              October 2006


   The syntax of the context parameter follows the same conventions as
   the same parameter in [RFC3966], that is, it appears between the
   digits and the @ in the userinfo [RFC3261] of the URI:

       ;domainname, DIGITS from RFC3261
   dialstring = digits ';phone-context=' domainname
   digits = phone-digit *( phone-digit / visual-separator)
   phone-digit = DIGIT / "A" / "a" / "B" / "b" / "C" / "c" / "D" / "d" /
                         "E" / "e" / "F" / "f" / "P" / "p" / "X" / "x" /
                         "*" / "#"
   visual-separator = "-" / "." / "(" / ")"

   A dialstring SHOULD NOT be used for an AoR in a REGISTER.  Parameters
   are ignored in registration.  Thus, two registrations with different
   phone-contexts would be considered equivalent, which is probably not
   desirable.

   A proxy server or Back to Back User Agent (B2BUA) [RFC3261] which is
   authoritative for the context may translate the dial string to a
   telephone number or service invocation URI.  If such a translation is
   performed, the proxy server MUST change the URI parameter value from
   "user=dialstring" to "user=phone".  This translation MUST occur prior
   to the call leaving the domain of the context.

   Examples of dial string use include:
   ;what a SIP Phone might emit when a user dials extension 123
sip:123;phone-context=atlanta.example.com@example.com;user=dialstring


   ;existing voicemail systems have a local access extension,
   ;then expect to see the extension number as DTMF for the mailbox
sip:450X123;phone-context=biloxi.example.com@example.com;user=dialstring


5.  IANA Considerations

   [RFC3969] defines a 'sip:' or 'sips:' URI Parameter sub registry.
   The "user" parameter is specified as having predefined values.

   This RFC defines a new value for the "user" parameter, "dialstring".
   This RFC must be added to the references listed for the "user"
   parameter.


6.  Security Considerations

   Dialstrings exposed to the Internet may reveal information about
   internal network details or service invocations that could allow



Rosen                    Expires April 23, 2007                 [Page 5]

Internet-Draft            Dialstring Parameter              October 2006


   attackers to use the PSTN or the Internet to attack such internal
   systems.  Dialstrings normally SHOULD NOT be sent beyond the domain
   of the UAC.  If they are sent across the Internet, they SHOULD be
   protected against eavesdropping with TLS per the procedures in
   [RFC3261].


7.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3261]  Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
              A., Peterson, J., Sparks, R., Handley, M., and E.
              Schooler, "SIP: Session Initiation Protocol", RFC 3261,
              June 2002.

   [RFC3966]  Schulzrinne, H., "The tel URI for Telephone Numbers",
              RFC 3966, December 2004.

   [RFC3969]  Camarillo, G., "The Internet Assigned Number Authority
              (IANA) Uniform Resource Identifier (URI) Parameter
              Registry for the Session Initiation Protocol (SIP)",
              BCP 99, RFC 3969, December 2004.


Author's Address

   Brian Rosen
   NeuStar
   470 Conrad Dr
   Mars, PA  16046
   US

   Phone: +1 724 382 1051
   Email: br@brianrosen.net















Rosen                    Expires April 23, 2007                 [Page 6]

Internet-Draft            Dialstring Parameter              October 2006


Full Copyright Statement

   Copyright (C) The Internet Society (2006).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
   ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
   INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
   INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.


Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.


Acknowledgment

   Funding for the RFC Editor function is provided by the IETF
   Administrative Support Activity (IASA).





Rosen                    Expires April 23, 2007                 [Page 7]


Html markup produced by rfcmarkup 1.107, available from http://tools.ietf.org/tools/rfcmarkup/