[Docs] [txt|pdf] [Tracker] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 RFC 4961

BEHAVE                                                           D. Wing
Internet-Draft                                             Cisco Systems
Intended status:  Best Current                            April 13, 2007
Practice
Expires:  October 15, 2007


                           Symmetric RTP/RTCP
                 draft-wing-behave-symmetric-rtprtcp-03

Status of this Memo

   By submitting this Internet-Draft, each author represents that any
   applicable patent or other IPR claims of which he or she is aware
   have been or will be disclosed, and any of which he or she becomes
   aware will be disclosed, in accordance with Section 6 of BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

   This Internet-Draft will expire on October 15, 2007.

Copyright Notice

   Copyright (C) The IETF Trust (2007).

Abstract

   This document recommends using one UDP port pair for both
   communication directions of bidirectional RTP and RTCP sessions,
   commonly called "symmetric RTP" and "symmetric RTCP."







Wing                    Expires October 15, 2007                [Page 1]

Internet-Draft           Symmetric RTP and RTCP               April 2007


Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . 3
   2.  Conventions Used in this Document . . . . . . . . . . . . . . . 3
   3.  Definition of Symmetric RTP and Symmetric RTCP  . . . . . . . . 4
   4.  Recommended Usage . . . . . . . . . . . . . . . . . . . . . . . 4
   5.  Security Considerations . . . . . . . . . . . . . . . . . . . . 5
   6.  IANA Considerations . . . . . . . . . . . . . . . . . . . . . . 5
   7.  Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . 5
   8.  References  . . . . . . . . . . . . . . . . . . . . . . . . . . 5
     8.1.  Normative References  . . . . . . . . . . . . . . . . . . . 5
     8.2.  Informational References  . . . . . . . . . . . . . . . . . 6
   Author's Address  . . . . . . . . . . . . . . . . . . . . . . . . . 6
   Intellectual Property and Copyright Statements  . . . . . . . . . . 8





































Wing                    Expires October 15, 2007                [Page 2]

Internet-Draft           Symmetric RTP and RTCP               April 2007


1.  Introduction

   TCP [RFC0793], which is inherently bidirectional, transmits and
   receives data using the same local port.  That is, when a TCP
   connection is established from host A with source TCP port "a" to a
   remote host, the remote host sends packets back to host A's source
   TCP port "a".

   However, UDP is not inherently bidirectional and UDP does not require
   using the same port for sending and receiving bidirectional traffic.
   Rather, some UDP applications use a single UDP port to transmit and
   receive (e.g., DNS [RFC1035]), some applications use different UDP
   ports to transmit and receive with explicit signaling (e.g., TFTP
   [RFC1350]), and other applications don't specify the choice of
   transmit and receive ports (RTP [RFC3550]).

   Because RTP and RTCP are not inherently bidirectional protocols, and
   UDP is not a bidirectional protocol, the usefulness of using the same
   UDP port for transmitting and receiving has been generally ignored
   for RTP and RTCP.  Many firewalls, NATs [RFC3022], and RTP
   implementations expect symmetric RTP, and do not work in the presence
   of asymmetric RTP.  However, this term has never been defined.  This
   document defines "symmetric RTP" and "symmetric RTCP".

   The UDP port number to receive media, and the UDP port to transmit
   media are both selected by the device that receives that media and
   transmits that media.  For unicast flows, the receive port is
   communicated to the remote peer (e.g., SDP [RFC4566] carried in SIP
   [RFC3261], SAP [RFC2974], or Megaco/H.248 [RFC3525]).

   There is no correspondence between the local RTP (or RTCP) port and
   the remote RTP (or RTCP) port.  That is, device "A" might choose its
   local transmit and receive port to be 1234.  Its peer, device "B", is
   not constrained to also use port 1234 for its port.  In fact, such a
   constraint is impossible to meet because device "B" might already be
   using that port for another application.

   The benefits of using one UDP port pair is described below in
   Section 4.


2.  Conventions Used in this Document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].





Wing                    Expires October 15, 2007                [Page 3]

Internet-Draft           Symmetric RTP and RTCP               April 2007


3.  Definition of Symmetric RTP and Symmetric RTCP

   A device supports symmetric RTP if it selects, communicates, and uses
   IP addresses and port numbers such that, when receiving a
   bidirectional RTP media stream on UDP port "A" and IP address "a", it
   also transmits RTP media for that stream from the same source UDP
   port "A" and IP address "a".  That is, it uses the same UDP port to
   transmit and receive one RTP stream.

   A device which doesn't support symmetric RTP would transmit RTP from
   a different port, or from a different IP address, than the port and
   IP address used to receive RTP for that bidirectional media steam.

   A device supports symmetric RTCP if it selects, communicates, and
   uses IP addresses and port numbers such that, when receiving RTCP
   packets for a media stream on UDP port "B" and IP address "b", it
   also transmits RTCP packets for that stream from the same source UDP
   port "B" and IP address "b".  That is, it uses the same UDP port to
   transmit and receive one RTCP stream.

   A device which doesn't support symmetric RTCP would transmit RTCP
   from a different port, or from a different IP address, than the port
   and IP address used to receive RTCP.


4.  Recommended Usage

   There are two specific instances where symmetric RTP and symmetric
   RTCP are REQUIRED:

   The first instance is NATs that lack integrated Application Layer
   Gateway (ALG) functionality.  Such NATs require that endpoints use
   symmetric UDP ports to establish bidirectional traffic.  This
   requirement exists for all types of NATs described in section 4 of
   [RFC4787].  ALGs are defined in section 4.4 of [RFC3022].

   The second instance is Session Border Controllers (SBCs) and other
   forms of RTP and RTCP relays (e.g., [I-D.ietf-behave-turn]).  Media
   relays are necessary to establish bidirectional UDP communication
   across a NAT that is 'Address-Dependent' or 'Address and Port-
   Dependent' [RFC4787].  However, even with a media relay, symmetric
   UDP ports are still required to traverse such a NAT.

   There are other instances where symmetric RTP and symmetric RTCP are
   helpful, but not required.  For example, if a firewall can expect
   symmetric RTP and symmetric RTCP then the firewall's dynamic per-call
   port filter list can be more restrictive compared to asymmetric RTP
   and asymmetric RTCP.  Symmetric RTP and symmetric RTCP can also ease



Wing                    Expires October 15, 2007                [Page 4]

Internet-Draft           Symmetric RTP and RTCP               April 2007


   debugging and troubleshooting.

   Other UDP-based protocols can also benefit from common local transmit
   and receive ports.

   There are no known cases where symmetric RTP or symmetric RTCP are
   harmful.

   For these reasons it is RECOMMENDED that symmetric RTP and symmetric
   RTCP always be used for bidirectional RTP media streams.


5.  Security Considerations

   If an attacker learns the source and destination UDP ports of a
   symmetric RTP or symmetric RTCP flow, the attacker can send RTP or
   RTCP packets to that host.  This differs from asymmetric RTP and
   asymmetric RTCP, where an attacker has to learn the UDP source and
   destination ports used for the reverse traffic, before it can send
   packets to that host.  Thus, if a host uses symmetric RTP or
   symmetric RTCP, an attacker need only see one RTP or RTCP packet in
   order to attack either RTP endpoint.  Note that this attack is
   similar to that of other UDP-based protocols that use one UDP port
   pair (e.g., DNS [RFC1035]).


6.  IANA Considerations

   This document doesn't require any IANA registrations.


7.  Acknowledgments

   The author thanks Francois Audet, Sunil Bhargo, Lars Eggert, Francois
   Le Faucheur, Cullen Jennings, Benny Rodrig, Robert Sparks, and Joe
   Stone for their assistance with this document.


8.  References

8.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.







Wing                    Expires October 15, 2007                [Page 5]

Internet-Draft           Symmetric RTP and RTCP               April 2007


8.2.  Informational References

   [RFC3550]  Schulzrinne, H., Casner, S., Frederick, R., and V.
              Jacobson, "RTP: A Transport Protocol for Real-Time
              Applications", STD 64, RFC 3550, July 2003.

   [RFC4787]  Audet, F. and C. Jennings, "Network Address Translation
              (NAT) Behavioral Requirements for Unicast UDP", BCP 127,
              RFC 4787, January 2007.

   [RFC0793]  Postel, J., "Transmission Control Protocol", STD 7,
              RFC 793, September 1981.

   [RFC3022]  Srisuresh, P. and K. Egevang, "Traditional IP Network
              Address Translator (Traditional NAT)", RFC 3022,
              January 2001.

   [RFC4566]  Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
              Description Protocol", RFC 4566, July 2006.

   [RFC1035]  Mockapetris, P., "Domain names - implementation and
              specification", STD 13, RFC 1035, November 1987.

   [RFC1350]  Sollins, K., "The TFTP Protocol (Revision 2)", STD 33,
              RFC 1350, July 1992.

   [I-D.ietf-behave-turn]
              Rosenberg, J., "Obtaining Relay Addresses from Simple
              Traversal Underneath NAT (STUN)",
              draft-ietf-behave-turn-03 (work in progress), March 2007.

   [RFC3261]  Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
              A., Peterson, J., Sparks, R., Handley, M., and E.
              Schooler, "SIP: Session Initiation Protocol", RFC 3261,
              June 2002.

   [RFC2974]  Handley, M., Perkins, C., and E. Whelan, "Session
              Announcement Protocol", RFC 2974, October 2000.

   [RFC3525]  Groves, C., Pantaleo, M., Anderson, T., and T. Taylor,
              "Gateway Control Protocol Version 1", RFC 3525, June 2003.










Wing                    Expires October 15, 2007                [Page 6]

Internet-Draft           Symmetric RTP and RTCP               April 2007


Author's Address

   Dan Wing
   Cisco Systems
   170 West Tasman Drive
   San Jose, CA  95134
   USA

   Email:  dwing@cisco.com










































Wing                    Expires October 15, 2007                [Page 7]

Internet-Draft           Symmetric RTP and RTCP               April 2007


Full Copyright Statement

   Copyright (C) The IETF Trust (2007).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
   THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
   OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.


Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.


Acknowledgment

   Funding for the RFC Editor function is provided by the IETF
   Administrative Support Activity (IASA).





Wing                    Expires October 15, 2007                [Page 8]


Html markup produced by rfcmarkup 1.109, available from https://tools.ietf.org/tools/rfcmarkup/