[Docs] [txt|pdf] [Tracker] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 draft-ietf-ccamp-gmpls-g709-framework

Network Working Group                                        Fatai Zhang
Internet Draft                                                    Dan Li
Category: Informational                                           Huawei
                                                                  Han Li
                                                                    CMCC
                                                               S.Belotti
                                                          Alcatel-Lucent
Expires: August 26, 2010                               February 27, 2010


                 Framework for GMPLS and PCE Control of
                    G.709 Optical Transport Networks

               draft-zhang-ccamp-gmpls-g709-framework-02.txt


Status of this Memo

   This Internet-Draft is submitted to IETF in full conformance with
   the provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

   This Internet-Draft will expire on June 16, 2010.



Abstract

   This document provides a framework to allow the development of
   protocol extensions to support Generalized Multi-Protocol Label
   Switching (GMPLS) and Path Computation Element (PCE) control of
   Optical Transport Networks (OTN) as specified in ITU-T Recommendation
   G.709 as consented in October 2009.




zhang                   Expires August 2010                  [Page 1]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


Table of Contents


   1. Introduction................................................2
   2. Terminology.................................................3
   3. G.709 Optical Transport Network (OTN)........................4
      3.1. OTN Layer Network.......................................4
   4. Connection management in OTN................................10
      4.1. Connection management of the ODU.......................10
   5. GMPLS/PCE Implications......................................13
      5.1. Implications for LSP Hierarchy with GMPLS TE...........13
      5.2. Implications for GMPLS Signaling.......................13
         5.2.1. Identifying OTN signals...........................13
         5.2.2. Tributary Port Number.............................14
      5.3. Implications for GMPLS Routing.........................15
         5.3.1. Requirement for conveying Interface Switching Capability
         specific information.....................................15
      5.4. Implications for Link Management Protocol (LMP).........16
         5.4.1. Correlating the Granularity of the TS.............16
         5.4.2. Correlating the Supported LO ODU Signal Types......16
      5.5. Implications for Path Computation Elements.............17
   6. Security Considerations.....................................17
   7. IANA Considerations........................................17
   8. Acknowledgments............................................17
   9. References.................................................18
      9.1. Normative References...................................18
      9.2. Informative References.................................19
   10. Authors' Addresses........................................19
   11. Contributors..............................................20
   APPENDIX A: Description of LO ODU terminology and ODU connection
   examples......................................................21


1. Introduction

   OTN has become a mainstream layer 1 technology for the transport
   network. Operators want to introduce control plane capabilities based
   on Generalized Multi-Protocol Label Switching (GMPLS) to OTN networks,
   to realize the benefits associated with a high-function control plane
   (e.g., improved network resiliency, resource usage efficiency, etc.).

   GMPLS extends MPLS to encompass time division multiplexing (TDM)
   networks (e.g., SONET/SDH, PDH, and G.709 sub-lambda), lambda
   switching optical networks, and spatial switching (e.g., incoming
   port or fiber to outgoing port or fiber). The GMPLS architecture is
   provided in [RFC3945], signaling function and Resource ReserVation
   Protocol-Traffic Engineering (RSVP-TE) extensions are described in


zhang                   Expires August 2010                  [Page 2]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


   [RFC3471] and [RFC3473], routing and OSPF extensions are described in
   [RFC4202] and [RFC4203], and the Link Management Protocol (LMP) is
   described in [RFC4204].

   The GMPLS protocol suite including provision [RFC4328] provides the
   mechanisms for basic GMPLS control of OTN networks based on the 2003
   revision of the G.709 specification [G709-V1]. Later revisions of the
   G.709 specification [G709-V3] have included some new features; for
   example, various multiplexing structures, two types of Tributary
   Slots (i.e., 1.25Gbps and 2.5Gbps), and extension of the Optical Data
   Unit (ODU) ODUj definition to include the ODUflex function.

   This document reviews relevant aspects of OTN technology evolution
   that affect the GMPLS control plane protocols and examines why and
   how to update the mechanisms described in [RFC4328]. This document
   additionally provides a framework for the GMPLS control of OTN
   networks and includes a discussion of the implication for the use of
   the Path Computation Element (PCE) [RFC4655].

   For the purposes of the control plane the OTN can be considered as
   being comprised of sub-wavelength (ODU) and wavelength (OCh) layers.
   This document focuses on the control of the sub-wavelength layer,
   with control of the wavelength layer considered out of the scope.
   Please refer to [WSON-Frame] for further information about the
   wavelength layer.

   [Note: It is intended to align this draft with G.709 (consented in
   10/2009), G.872 and G.8080 (planned for consent in 6/2010)]

2. Terminology

   OTN: Optical Transport Network

   ODU: Optical Channel Data Unit

   OTU: Optical channel transport unit

   OMS: Optical multiplex section

   MSI: Multiplex Structure Identifier

   TPN: Tributary Port Number

   LO ODU: Lower Order ODU. The LO ODUj (j can be 0, 1, 2, 2e, 3, 4,
   Flex.) represents the container transporting a client of the OTN that
   is either directly mapped into an OTUk (k = j) or multiplexed into a
   server HO ODUk (k > j)container.


zhang                   Expires August 2010                  [Page 3]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


   HO ODU: Higher Order ODU. The HO ODUk (k can be 1, 2, 2e, 3, 4.)
   represents the entity transporting a multiplex of LO ODUj tributary
   signals in its OPUk area.

   ODUflex: Flexible ODU. A flexible ODUk can have any bit rate and a
   bit rate tolerance up to 100 ppm.

3. G.709 Optical Transport Network (OTN)

   This section provides an informative overview of those aspects of the
   OTN impacting control plane protocols.  This overview is based on the
   ITU-T Recommendations that contain the normative definition of the
   OTN. Technical details regarding OTN architecture and interfaces are
   provided in the relevant ITU-T Recommendations.

   Specifically, [ITU-T-G.872] describes the functional architecture of
   optical transport networks providing optical signal transmission,
   multiplexing, routing, supervision, performance assessment, and
   network survivability.  [G709-V1] defines the interfaces of the
   optical transport network to be used within and between subnetworks
   of the optical network.  With the evolution and deployment of OTN
   technology many new features have been specified in ITU-T
   recommendations, including for example, new ODU0, ODU2e, ODU4 and
   ODUflex containers as described in [G709-V3].


3.1. OTN Layer Network

   The simplified signal hierarchy of OTN is shown in Figure 1, which
   illustrates the layers that are of interest to the control plane.
   Other layers below OCh (e.g. Optical Transmission Section - OTS) are
   not included in this Figure. The full signal hierarchy is provided in
   [G709-V3].

                               Client signal
                                    |
                                   ODUj
                                    |
                                 OTU/OCh
                                   OMS

                    Figure 1 Basic OTN signal hierarchy





zhang                   Expires August 2010                  [Page 4]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


   Client signals are mapped into ODUj containers. These ODUj containers
   are multiplexed onto the OTU/OCh. The individual OTU/OCh signals are
   combined in the Optical Multiplex Section (OMS) using WDM
   multiplexing, and this aggregated signal provides the link between
   the nodes.

   3.1.1 Client signal mapping

   The client signals are mapped into a Low Order (LO) ODUj. Appendix A
   gives more information about LO ODU.

   The current values of j defined in [G709-V3] are: 0, 1, 2, 2e, 3, 4,
   Flex. The approximate bit rates of these signals are defined in
   [G709-V3] and are reproduced in Tables 1 and 2.


   +-----------------------+-----------------------------------+
   |       ODU Type        |       ODU nominal bit rate        |
   +-----------------------+-----------------------------------+
   |         ODU0          |         1 244 160 kbits/s         |
   |         ODU1          |    239/238 x 2 488 320 kbit/s     |
   |         ODU2          |    239/237 x 9 953 280 kbit/s     |
   |         ODU3          |    239/236 x 39 813 120 kbit/s    |
   |         ODU4          |    239/227 x 99 532 800 kbit/s    |
   |         ODU2e         |    239/237 x 10 312 500 kbit/s    |
   |                       |                                   |
   |    ODUflex for CBR    |                                   |
   |    Client signals     | 239/238 x client signal bit rate  |
   |                       |                                   |
   |   ODUflex for GFP-F   |                                   |
   | Mapped client signal  |        Configured bit rate        |
   +-----------------------+-----------------------------------+

                      Table 1 ODU types and bit rates

   NOTE - The nominal ODUk rates are approximately: 2 498 775.126 kbit/s
   (ODU1), 10 037 273.924 kbit/s (ODU2), 40 319 218.983 kbit/s (ODU3),
   104 794 445.815 kbit/s (ODU4) and 10 399 525.316 kbit/s (ODU2e).







zhang                   Expires August 2010                  [Page 5]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


   +-------------------+--------------------------------------+
   |     ODU Type      |        ODU bit-rate tolerance        |
   +-------------------+--------------------------------------+
   |       ODU0        |             +- 20 ppm                |
   |       ODU1        |             +- 20 ppm                |
   |       ODU2        |             +- 20 ppm                |
   |       ODU3        |             +- 20 ppm                |
   |       ODU4        |             +- 20 ppm                |
   |       ODU2e       |             +- 100 ppm               |
   |                   |                                      |
   |  ODUflex for CBR  |                                      |
   |  Client signals   |  client signal bit rate tolerance,   |
   |                   |      with a maximum of+-100 ppm      |
   |                   |                                      |
   | ODUflex for GFP-F |                                      |
   |   Mapped client   |             +- 20 ppm                |
   |      signal       |                                      |
   +-------------------+--------------------------------------+
                      Table 2 ODU types and tolerance

   One of two options are for mapping client signals into ODUflex
   depending on the client signal type:
   -  Circuit clients are proportionally wrapped. Thus the bit rate and
       tolerance are defined by the client signal.

   -  Packet clients are mapped using the Generic Framing Procedure
   (GFP). [G709-V3] recommends that the bit rate should be set to an
   integer multiplier of the High Order (HO) Optical Channel Physical
   Unit (OPU) OPUk Tributary Slot (TS) rate, the tolerance should be +/-
   20ppm, and the bit rate should be determined by the node that
   performs the mapping.

   3.1.1.1 ODUj types and parameters

   When ODUj connections are setup, two types of information should be
   conveyed in a connection request:

   (a)End to end:
   Client payload type (e.g. STM64; Ethernet etc.)

   Bit rate and tolerance:  Note for j = 0, 1, 2, 2e, 3, 4 this
   information may be carried as an enumerated type.  For the ODUflex
   the actual bit rate and tolerance must be provided.


zhang                   Expires August 2010                  [Page 6]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


   (b)Hop by hop:
   TS assignment and port number carried by the Multiplex Structure
   Identifier (MSI) bytes as described in section 3.1.2.

   3.1.2 Multiplexing ODUj onto Links

   The links between the switching nodes are provided by one or more
   wavelengths.  Each wavelength carries one OCh, which carries one OTU,
   which carries one OPU.  Since all of these signals have a 1:1:1
   relationship, we only refer to the OTU for clarity.  The ODUjs are
   mapped into the Tributary Slots (TS) of the OTUk.  Note that in the
   case where j=k the ODUj is mapped into the OTU/OCh without
   multiplexing.

   The initial versions of G.709 [G709-V1] only provided a single TS
   granularity, nominally 2.5Gb/s.  Amendment 3 [G709-V3], approved in
   2009, added an additional TS granularity, nominally 1.25Gb/s. The
   number and type of TSs provided by each of the currently identified
   OTUk is provided below:

       2.5Gb/s  1.25Gb/s  Nominal Bit rate
   OTU1    1      2         2.5Gb/s
   OTU2    4      8          10Gb/s
   OTU3   16     32          40Gb/s
   OTU4   --     80         100Gb/s

   To maintain backwards compatibility while providing the ability to
   interconnect nodes that support 1.25Gb/s TS at one end of a link and
   2.5Gb/s TS at the other, the 'new' equipment will fall back to the
   use of a 2.5Gb/s TS if connected to legacy equipment.  This
   information is carried in band by the payload type.

   The actual bit rate of the TS in an OTUk depends on the value of k.
   Thus the number of TS occupied by an ODUj may vary depending on the
   values of j and k.  For example an ODU2e uses 9 TS in an OTU3 but
   only 8 in an OTU4. Examples of the number of TS used for various
   cases are provided below:

   -  ODU0 into ODU1, ODU2, ODU3 or ODU4 multiplexing with 1,25Gbps TS
       granularity
      o ODU0 occupies 1 of the 2, 8, 32 or 80 TS for ODU1, ODU2, ODU3 or
        ODU4





zhang                   Expires August 2010                  [Page 7]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


   -  ODU1 into ODU2, ODU3 or ODU4 multiplexing with 1,25Gbps TS
       granularity
      o ODU1 occupies 2 of the 8, 32 or 80 TS for ODU2, ODU3 or ODU4

   -  ODU1 into ODU2, ODU3 multiplexing with 2.5Gbps TS granularity
      o ODU1 occupies 1 of the 4 or 16 TS for ODU2 or ODU3

   -  ODU2 into ODU3 or ODU4 multiplexing with 1.25Gbps TS granularity
      o ODU2 occupies 8 of the 32 or 80 TS for ODU3 or ODU4

   -  ODU2 into ODU3 multiplexing with 2.5Gbps TS granularity
      o ODU2 occupies 4 of the 16 TS for ODU3

   -  ODU3 into ODU4 multiplexing with 1.25Gbps TS granularity
      o ODU3 occupies 31 of the 80 TS for ODU4

   -  ODUflex into ODU2, ODU3 or ODU4 multiplexing with 1.25Gbps TS
       granularity
      o ODUflex occupies n of the 8, 32 or 80 TS for ODU2, ODU3 or ODU4
        (n <= Total TS numbers of ODUk)

   -  ODU2e into ODU3 or ODU4 multiplexing with 1.25Gbps TS granularity
      o ODU2e occupies 9 of the 32 TS for ODU3 or 8 of the 80 TS for
        ODU4

   In general the mapping of an ODUj (including ODUflex) into the OTUk
   TSs is determined locally, and it can also be explicitly controlled
   by a specific entity (e.g., head end, NMS) through Explicit Label
   Control [RFC3473].

   3.1.2.1 Link Parameters

   Per [RFC4201], each OTU can be treated as a component link of a link
   bundle. The available capacity between nodes is the sum of the
   available capacity on the OTUs that interconnect the nodes. This
   total capacity is represented as the capacity of a link bundle.

   Note that there will typically be more than one OTU between a pair of
   nodes so that the available capacity will typically be distributed
   across multiple OTUs. Thus, in order to be able to determine the
   maximum payload that can be carried on a bundled link, the link state
   advertisement must also provide the largest number of TSes available
   on any one component OTU.


zhang                   Expires August 2010                  [Page 8]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


   In order to compute the lowest cost path for a ODUj connection
   request the critical parameters that need to be provided (for the
   purposes of routing) are:

   -  Number of TS

   -  Maximum number of TS available for a LSP (i.e., Maximum LSP
   Bandwidth)

   -  Bit rate of the TS. (Note: This may be efficiently encoded as a
   two integers representing the value of k and the granularity.)

   3.1.2.2 Tributary Port Number Assignment

   When multiplexing an ODUj into a HO ODUk (k>j), G.709 specifies the
   information that has to be transported in-band in order to allow for
   correct demultiplexing. This information, known as Multiplex
   Structure Information (MSI), is transported in the OPUk overhead and
   is organized as a set of entries, with one entry for each HO ODUj
   tributary slot.  The information carried by each entry is:

   Payload Type:  the type of the transported payload

   Tributary Port Number (TPN):  the port number of the ODUj transported
   by the HO ODUk. The TPN is the same for all the tributary slots
   assigned to the transport of the same ODUj instance.

   For example, an ODU2 carried by a HO ODU3 is described by 4 entries
   in the OPU3 overhead when the Tributary Slot (TS) size is 2.5 Gbit/s,
   and by 8 entries when the TS size is 1.25 Gbit/s.

   The MSI information inserted in OPU3 overhead by the source of the HO
   ODUk trail is checked by the sink of the HO ODUk trail.  G.709
   default behavior requires that the multiplexing structure of the HO
   ODUk be provided by means of pre-provisioned MSI information, termed
   expectedMSI.  The sink of the HO ODU trail checks the complete
   content of the MSI information (including the TPN) that was received
   in-band, termed acceptedMSI, against the expectedMSI.  If the
   acceptedMSI  is different from the expectedMSI, then the traffic is
   dropped and a payload mismatch alarm is generated.

   Note that the values of the TPN MUST be either agreed between the
   source and the sink of the HO ODU trail  either via control plane
   signaling or provisioning by the management plane.





zhang                   Expires August 2010                  [Page 9]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


4. Connection management in OTN

   As [ITU-T-G.872] described, OTN-based transport network equipment is
   concerned with control of connectivity of ODU paths and optical
   channels and not with control of connectivity of the client layer.
   This document focuses on the connection management of ODU paths.  The
   management of OCh paths is described in [WSON-FRAME].

   Current [ITU-T-G.872] considers the ODU as a set of layers in the
   same way as SDH has been modeled.  However, recent progress within
   the ITU-T on OTN architecture includes an agreement to update this
   Recommendation to model the ODU  as a single layer network with the
   bit rate as a parameter of links and connections. This will allow the
   links and nodes to be viewed in a single topology as a common set of
   resources that are available to provide ODUj connections independent
   of the value of j. Note that when the bit rate of ODUj is less than
   the server bit rate, ODUj connections are supported by HO-ODU (which
   has a one-to-one relationship with the OTU).

   From an ITU-T perspective, the service layer is represented by the LO
   ODU and the connection topology is represented by that of the server
   layer; i.e., the OTU [corresponding to HO-ODU in case of multiplexing
   or to LO-ODU in case of direct mapping] which has the same topology
   as that of the OCh layer. The server layer topology is based on that
   of the OTU, and could be provided by a point-to-point optical
   connection, flexible optical connection that is fully in the optical
   domain, flexible optical connection involving hybrid sub-
   lambda/lambda nodes involving 3R, etc.

   The HO-ODU/OTU and OCh layers should be visible in a single
   topological representation of the network, and from a logical
   perspective, the HO ODU/OTU and OCh may be considered as the same
   logical, switchable entity.

   The remainder of this document assumes that the revision of G.872
   will be made. The document will be updated to keep it in line with
   the new revision of G.872 when it is consented for publication.

4.1. Connection management of the ODU

   LO ODUj can be either mapped into the OTUk signal (j = k), or
   multiplexed with other LO ODUjs into an OTUk (j < k), and the OTUk is
   mapped into an OCh. See Appendix A for more information.

   From the perspective of control plane, there are two kinds of network
   topology to be considered.



zhang                   Expires August 2010                 [Page 10]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


   (1) ODU layer

   In this case, the ODU links are presented between adjacent OTN nodes,
   which is illustrated in Figure 2. In this layer there are ODU links
   with a variety of TSes available, and nodes that are ODXCs. Lo ODU
   connections can be setup based on the network topology.

                  Link #5       +--+---+--+        Link #4
     +--------------------------|         |--------------------------+
     |                          |  ODXC   |                          |
     |                          +---------+                          |
     |                             Node E                            |
     |                                                               |
   +-++---+--+        +--+---+--+        +--+---+--+        +--+---+-++
   |         |Link #1 |         |Link #2 |         |Link #3 |         |
   |         |--------|         |--------|         |--------|         |
   |  ODXC   |        |  ODXC   |        |  ODXC   |        |  ODXC   |
   +---------+        +---------+        +---------+        +---------+
      Node A             Node B              Node C            Node D

  Figure 2 Example Topology for connection LO ODU connection management

   If an ODUj connection is requested between Node C and Node E
   routing/path computation must select a path that has the required
   number of TS available and that offers the lowest cost.  Signaling is
   then invoked to set up the path and to provide the information (e.g.,
   selected TS) required by each transit node to allow the configuration
   of the ODUj to OTUk mapping (j = k) or multiplexing (j < k),  and
   demapping (j = k) or demultiplexing (j < k).

   (2)ODU layer with OCh switching capability

   In this case, the OTN nodes interconnect with wavelength switched
   node (e.g., ROADM,OXC) that are capable of OCh switching, which is
   illustrated in Figure 3 and Figure 4. There are ODU layer and OCh
   layer, so it is simply a MLN. OCh connections may be created on
   demand, which is described in section 5.1.

   In this case, an operator may choose to allow the underlined OCh
   layer to be visible to the ODU routing/path computation process in
   which case the topology would be as shown in Figure 4. In Figure 3
   below, instead, a cloud representing OCH capable switching nodes is
   represented. In Figure 3, the operator choice is to hide the real RWA
   network topology.


                                 Node E


zhang                   Expires August 2010                 [Page 11]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


          Link #5              +---------+      Link #4
    +--------------------------|         |-------------------------+
    |                            ------                            |
    |                         //        \\                         |
    |                        ||          ||                        |
    |                        | RWA domain |                        |
  +-+-------+        +----+- ||          || ------+        +-------+-+
  |         |        |        \\        //        |        |         |
  |         |Link #1 |          --------          |Link #3 |         |
  |         +--------+         |        |         +--------+         +
  | ODXC    |        |  ODXC   +--------+  ODXC   |        | ODXC    |
  +---------+        +---------+Link #2 +---------+        +---------+
    Node A              Node B             Node C            Node D


Figure 3 RWA Hidden Topology for connection LO ODU connection management



            Link #5            +---------+            Link #4
    +--------------------------|         |-------------------------+
    |                     +----+ ODXC    |----+                    |
    |                   +-++   +---------+   ++-+                  |
    |           Node f  +  +     Node E      +  +  Node g          |
    |                   +-++                 ++-+                  |
    |                     |       +--+        |                    |
  +-+-------+        +----+----+--|  +--+-----+---+        +-------+-+
  |         |Link #1 |         |  +--+  |         |Link #3 |         |
  |         +--------+         | Node h |         +--------+         +
  | ODXC    |        | ODXC    +--------+ ODXC    |        | ODXC    |
  +---------+        +---------+ Link #2+---------+        +---------+
    Node A              Node B            Node C             Node D

     Figure 4 RWA Visible Topology for LO ODUj connection management

   In Figure 4, the cloud of previous figure is substitute by the real
   topology. The nodes f,g,h are nodes with OCH switching capability.

   In the examples (i.e., Figure 3 and Figure 4), we have considered the
   case in which LO-ODUj connections are supported by OCh connection,
   and the case in which the supporting underlying connection can be
   also made by a combination of HO-ODU/OCh connections.

   In this case, the ODU routing/path selection process will request an
   HO-ODU/OCh connection between node C to node E from the RWA domain.
   The connection will appear at ODU level as a Forwarding Adjacency,
   which will be used to create the ODU connection.


zhang                   Expires August 2010                 [Page 12]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010



5. GMPLS/PCE Implications

   The purpose of this section is to provide a framework for extensions
   of the current GMPLS protocol suite and the PCE applications and
   protocols to encompass OTN enhancements and connection management.

5.1. Implications for LSP Hierarchy with GMPLS TE

   The path computation for LO ODU connection request is based on the
   topology of ODU layer, including OCh layer visibility.

   The OTN path computation can be divided into two layers. One layer is
   OCh/OTUk, the other is LO ODUj. [RFC4206] defines the mechanisms to
   accomplish creating the hierarchy of LSPs. The LSP management of
   multiple layers in OTN can follow the procedures defined in [RFC4206]
   and related MLN drafts.

   As discussed in section 4, the route path computation for OCh is in
   the scope of WSON [WSON-Frame]. Therefore, this document only
   considers ODU layer for LO ODU connection request.

5.2. Implications for GMPLS Signaling

   The signaling function and Resource reSerVation Protocol-Traffic
   Engineering (RSVP-TE) extensions are described in [RFC3471] and [RFC
   3473]. For OTN-specific control, [RFC4328] defines signaling
   extensions to support G.709 Optical Transport Networks Control as
   defined in [G709-V1].

   As described in Section 2, [G709-V3] introduced some new features
   that include the ODU0, ODU2e, ODU4 and ODUflex containers. The
   mechanisms defined in [RFC4328] do not support such new OTN features,
   and protocol extensions will be necessary to allow them to be
   controlled by a GMPLS control plane.

   5.2.1. Identifying OTN signals

   [RFC4328] defines the LSP Encoding Type, the Switching Type and the
   Generalized Protocol Identifier (Generalized-PID) constituting the
   common part of the Generalized Label Request. The G.709 Traffic
   Parameters are also defined in [RFC4328].  The following new signal
   types have been added since [RFC4328] was published:

   (1)New signal types of sub-lambda layer

      Optical Channel Data Unit (ODUj):


zhang                   Expires August 2010                 [Page 13]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


           ODU0

           ODU2e

           ODU4

           ODUflex

   (2)A new Tributary Slot (TS) granularity (i.e., 1.25 Gbps)

   (3)Signal type with variable bandwidth:

      ODUflex has a variable bandwidth/bit rate BR and a bit rate
      tolerance T. As described above the (node local) mapping process
      must be aware of the bit rate and tolerance of the ODUj being
      multiplexed in order to select the correct number of TS and the
      fixed/variable stuffing bytes. Therefore, bit rate and bit rate
      tolerance should be carried in the Traffic Parameter in the
      signaling of connection setup request.

   (4)Extended multiplexing hierarchy (For example, ODU0 into OTU2
        multiplexing (with 1,25Gbps TS granularity).)

   So the encoding provided in [RFC4328] needs to be extended to support
   all the signal types and related mapping and multiplexing with all
   kinds of tributary slots. Moreover, the extensions should consider
   the extensibility to match future evolvement of OTN.

   For item (1) and (3), new traffic parameters may need to be extended
   in signaling message;

   For item (2) and (4), new label should be defined to carry the exact
   TS allocation information related to the extended multiplexing
   hierarchy.

   5.2.2. Tributary Port Number

   The tributary port number may be assigned locally by the node at the
   (traffic) ingress end of the link and in this case as described above
   must be conveyed to the far end of the link as a "transparent"
   parameter i.e. the control plane does not need to understand this
   information. The TPN may also be assigned by the control plane as a
   part of path computation.






zhang                   Expires August 2010                 [Page 14]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


5.3. Implications for GMPLS Routing

   The path computation process should select a suitable route for a
   ODUj connection request. In order to compute the lowest cost path it
   must evaluate the number (and availability) of tributary slots on
   each candidate link.  The routing protocol should be extended to
   convey some information to represent ODU TE topology.  As described
   above the number of tributary slots (on a link bundle), the bandwidth
   of the TS and the maximum number that are available to convey a
   single ODUj must be provided.

   GMPLS Routing [RFC4202] defines Interface Switching Capability
   Descriptor of TDM which can be used for ODU. However, some other
   issues should also be considered which are discussed below.

5.3.1. Requirement for conveying Interface Switching Capability specific
   information

   Interface Switching Capability Descriptors present a new constraint
   for LSP path computation. [RFC4203] defines the switching capability
   and related Maximum LSP Bandwidth and the Switching Capability
   specific information. When the Switching Capability field is TDM the
   Switching Capability specific information field includes Minimum LSP
   Bandwidth, an indication whether the interface supports Standard or
   Arbitrary SONET/SDH, and padding. So routing protocol should be
   extended when TDM is ODU type to support representation of ODU
   switching information.

   As discussed in section 3.1.2, many different types of ODUj can be
   multiplexed into the same OTUk. For example, both ODU0 and ODU1 may
   be multiplexed into ODU2. An OTU link may support one or more types
   of ODUj signals. The routing protocol should be extended to carry
   this multiplexing capability. Furthermore, one type of ODUj can be
   multiplexed to an OTUk using different tributary slot granularity.
   For example, ODU1 can be multiplexed into ODU2 with either 2.5Gbps TS
   granularity or 1.25G TS granularity. The routing protocol should be
   extended to carry which TS granularity supported by the ODU interface.

   Moreover, the bit rate (i.e., bandwidth) of TS can be determined by
   the TS granularity and link type of the TE link. For example, the
   bandwidth of a 1.25G TS without NJO (Negative Justification
   Opportunity) in an OTU2 is about 1.249409620 Gbps, while the
   bandwidth of a 1.25G TS without NJO in an OTU3 is about 1.254703729
   Gbps. So The routing protocol should be extended to carry the TE link
   type (OTUk/HO ODUk).




zhang                   Expires August 2010                 [Page 15]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


   In OTN networks, it is simpler to use the number of Tributary Slots
   for the bandwidth accounting. For example, Total bandwidth of the TE
   link, Unreserved Bandwidth of the TE link and the Maximum LSP
   Bandwidth can be accounted through the number of Tributary Slots
   (e.g., the total number of the Tributary Slots of the TE link, the
   unreserved Tributary Slots of the TE link, Maximum Tributary Slots
   for an LSP). Thus, the routing protocol should be extended to carry
   the Tributary Slots information related to bandwidth of the TE link.

5.4. Implications for Link Management Protocol (LMP)

   As discussed in section 5.3, Path computation needs to know the
   interface switching capability of links. The switching capability of
   two ends of the link may be different, so the link capability of two
   ends should be correlated.

   The Link Management Protocol (LMP) [RFC4204] provides a control plane
   protocol for exchanging and correlating link capabilities.

   It is not necessary to use LMP to correlate link-end capabilities if
   the information is available from another source such as management
   configuration or automatic discovery/negotiation within the data
   plane.

   Note that LO ODU type information can be, in principle, discovered by
   routing. Since in certain case, routing is not present (e.g. UNI case)
   we need to extend link management protocol capabilities to cover this
   aspect. In case of routing presence, the discovering procedure by LMP
   could also be optional.

   5.4.1. Correlating the Granularity of the TS

   As discussed in section 3.1.2, the two ends of a link may support
   different TS granularity. In order to allow interconnection the node
   with 1.25Gb/s granularity must fall back to 2.5Gb/s granularity.

   Therefore, it is necessary for the two ends of a link to correlate
   the granularity of the TS.  This ensures that both ends of the link
   advertise consistent capabilities (for routing) and ensures that
   viable connections are established.

   5.4.2.  Correlating the Supported LO ODU Signal Types

   Many new ODU signal types have been introduced [G709-V3], such as
   ODU0, ODU4, ODU2e and ODUflex. It is possible that equipment does not
   support all the LO ODU signal types introduced by those new standards
   or drafts. If one end of a link can not support a certain LO ODU


zhang                   Expires August 2010                 [Page 16]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


   signal type, the link cannot be selected to carry such type of LO ODU
   connection.

   Therefore, it is necessary for the two ends of an HO ODU link to
   correlate which types of LO ODU can be supported by the link. After
   correlating, the capability information can be flooded by IGP, so
   that the correct path for an ODU connection can be calculated.

5.5. Implications for Path Computation Elements

   [PCE-APS] describes the requirements for GMPLS applications of PCE in
   order to establish GMPLS LSP. PCE needs to consider the GMPLS TE
   attributes appropriately once a PCC or another PCE requests a path
   computation. The TE attributes which can be contained in the path
   calculation request message from the PCC or the PCE defined in
   [RFC5440] includes switching capability, encoding type, signal type,
   etc.

   As described in section 5.2.1, new signal types and new signals with
   variable bandwidth information need to be carried in the extended
   signaling message of path setup. For the same consideration, PCECP
   also has a desire to be extended to carry the new signal type and
   related variable bandwidth information when a PCC requests a path
   computation.

6. Security Considerations

   The use of control plane protocols for signaling, routing, and path
   computation opens an OTN to security threats through attacks on those
   protocols. The data plane technology for an OTN does not introduce
   any specific vulnerabilities, and so the control plane may be secured
   using the mechanisms defined for the protocols discussed.

   For further details of the specific security measures refer to the
   documents that define the protocols ([RFC3473], [RFC4203], [RFC4205],
   [RFC4204], and [RFC5440]). [GMPLS-SEC] provides an overview of
   security vulnerabilities and protection mechanisms for the GMPLS
   control plane.

7. IANA Considerations

   This document makes not requests for IANA action.

8. Acknowledgments

   We would like to thank Maarten Vissers for his review and useful
   comments.


zhang                   Expires August 2010                 [Page 17]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


9. References

9.1. Normative References


   [RFC4328]   D. Papadimitriou, Ed. "Generalized Multi-Protocol Label
               Switching (GMPLS) Signaling Extensions for G.709 Optical
               Transport Networks Control", RFC 4328, Jan 2006.

   [RFC3471]   Berger, L., Editor, "Generalized Multi-Protocol Label
               Switching (GMPLS) Signaling Functional Description",
               RFC 3471, January 2003.

   [RFC3473]  L. Berger, Ed., "Generalized Multi-Protocol Label
               Switching (GMPLS) Signaling Resource ReserVation
               Protocol-Traffic Engineering (RSVP-TE) Extensions", RFC
               3473, January 2003.

   [RFC4202]  K. Kompella, Y. Rekhter, Ed., "Routing Extensions in
               Support of Generalized Multi-Protocol Label Switching
               (GMPLS)", RFC 4202, October 2005.

   [RFC4203]  K. Kompella, Y. Rekhter, Ed., "OSPF Extensions in Support
               of Generalized Multi-Protocol Label Switching (GMPLS)",
               RFC 4203, October 2005.

   [RFC4205]  K. Kompella, Y. Rekhter, Ed., "Intermediate System to
               Intermediate System (IS-IS) Extensions in Support of
               Generalized Multi-Protocol Label Switching (GMPLS)", RFC
               4205, October 2005.

   [RFC4204]   Lang, J., Ed., "Link Management Protocol (LMP)", RFC
                4204, October 2005.

   [RFC4206]   K. Kompella, Y. Rekhter, Ed., " Label Switched Paths
               (LSP) Hierarchy with Generalized Multi-Protocol Label
               Switching (GMPLS) Traffic Engineering (TE)", RFC 4206,
               October 2005.

   [RFC5440]   JP. Vasseur, JL. Le Roux, Ed.," Path Computation Element
               (PCE) Communication Protocol (PCEP)", RFC 5440, March
               2009.

   [G709-V3]   ITU-T, "Interfaces for the Optical Transport Network
               (OTN)", G.709 Recommendation, December 2009.


zhang                   Expires August 2010                 [Page 18]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010




9.2. Informative References

   [G709-V1]   ITU-T, "Interface for the Optical Transport Network
               (OTN)," G.709 Recommendation, March 2003.

   [ITU-T-G.872] ITU-T, "Architecture of optical transport networks",
                 November 2001 (11 2001).

   [HZang00]  H. Zang, J. Jue and B. Mukherjeee, "A review of routing
               and wavelength assignment approaches for wavelength-
               routed optical WDM networks", Optical Networks Magazine,
               January 2000.

   [WSON-FRAME] Y. Lee, G. Bernstein, W. Imajuku, "Framework for GMPLS
                and PCE Control of Wavelength Switched Optical Networks
                (WSON)", draft-ietf-ccamp-rwa-wson-framework, work in
                progress.

   [PCE-APS]  Tomohiro Otani, Kenichi Ogaki, Diego Caviglia, and Fatai
               Zhang, "Requirements for GMPLS applications of PCE",
               draft-ietf-pce-gmpls-aps-req-01.txt, July 2009.

   [GMPLS-SEC] Fang, L., Ed., "Security Framework for MPLS and GMPLS
               Networks", Work in Progress, October 2009.

10. Authors' Addresses

   Fatai Zhang
   Huawei Technologies
   F3-5-B R&D Center, Huawei Base
   Bantian, Longgang District
   Shenzhen 518129 P.R.China

   Phone: +86-755-28972912
   Email: zhangfatai@huawei.com


   Dan Li
   Huawei Technologies Co., Ltd.
   F3-5-B R&D Center, Huawei Base
   Bantian, Longgang District
   Shenzhen 518129 P.R.China

   Phone: +86-755-28973237
   Email: danli@huawei.com


zhang                   Expires August 2010                 [Page 19]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010



   Han Li
   China Mobile Communications Corporation
   53 A Xibianmennei Ave. Xuanwu District
   Beijing 100053 P.R. China

   Phone: +86-10-66006688
   Email: lihan@chinamobile.com


   Sergio Belotti
   Alcatel-Lucent
   Optics CTO
   Via Trento 30 20059 Vimercate (Milano) Italy
   +39 039 6863033

   Email: sergio.belotti@alcatel-lucent.it


11. Contributors

   Jianrui Han
   Huawei Technologies Co., Ltd.
   F3-5-B R&D Center, Huawei Base
   Bantian, Longgang District
   Shenzhen 518129 P.R.China

   Phone: +86-755-28972913
   Email: hanjianrui@huawei.com


   Malcolm Betts
   Huawei Technologies Co., Ltd.

   Email: malcolm.betts@huawei.com


   Pietro Grandi
   Alcatel-Lucent
   Optics CTO
   Via Trento 30 20059 Vimercate (Milano) Italy
   +39 039 6864930

   Email: pietro_vittorio.grandi@alcatel-lucent.it


   Eve Varma


zhang                   Expires August 2010                 [Page 20]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


   Alcatel-Lucent
   1A-261, 600-700 Mountain Av
   PO Box 636
   Murray Hill, NJ  07974-0636
   USA
   Email: eve.varma@alcatel-lucent.com

   APPENDIX A: Description of LO ODU terminology and ODU connection
   examples.

   This appendix provides a description of LO ODU terminology and ODU
   connection examples. This section is not normative which is just a
   reference in order to facilitate quicker understanding of text.

   In order to transmit client signal, the LO ODU connection must be
   created first. From the perspective of [G709-V3], there are two types
   of LO ODU:

   (1) A LO ODUj mapped into an OTUk. In this case, the server layer of
   this LO ODU is an OTUk. For example, if a STM-16 signal is
   encapsulated into ODU1, and then ODU1 is mapped into OTU1, the ODU1
   is a LO ODU.

   (2) A LO ODUj multiplexed into a HO ODUk (j < k)  occupying several
   TSs. In this case, the server layer of this LO ODU is a HO ODUk. For
   example, if ODU1 is multiplexed into ODU2, and ODU2 is mapped into
   OTU2, the ODU1 is LO ODU and ODU2 is HO ODU.

   The LO ODUj represents the container transporting a client of the OTN
   that is either directly mapped into an OTUk (k = j) or multiplexed
   into a server HO ODUk (k > j)container. Consequently, the HO ODUk
   represents the entity transporting a multiplex of LO ODUj tributary
   signals in its OPUk area.

   In the case of LO ODUj mapped into an OTUk (k = j) directly, Figure 5
   give an example of this kind of LO ODU connection.

   In Figure 5, The LO ODUj is switched at the intermediate ODXC node.
   OCh and OTUk are associated with each other. From the viewpoint of
   connection management, the management of OTUk is similar with OCh. LO
   ODUj and OCh/OTUk have client/server relationships.

   For example, one LO ODU1 connection can be setup between Node A and
   Node C. This LO ODU1 connection is to be supported by OCh/OTU1
   connections, which are to be set up between Node A and Node B and
   between Node B and Node C. LO ODU1 can be mapped into OTU1 at Node A,



zhang                   Expires August 2010                 [Page 21]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


   demapped from it in Node B, switched at Node B, and then mapped into
   the next OTU1 and demapped from this OTU1 at Node C.


      |                            LO ODUj                         |
      +------------------------------(b)---------------------------+
      |      |      OCh/OTUk      |     |    OCh/OTUk        |     |
      |      +--------(a)---------+     +--------(a)---------+     |
      |      |                    |     |                    |     |
     +------++-+                +--+---+--+                +-++------+
     |      |EO|                |OE|   |EO|                |OE|      |
     |      +--+----------------+--+   +--+----------------+--+      |
     |  ODXC   |                |  ODXC   |                |  ODXC   |
     +---------+                +---------+                +---------+
      Node A                     Node B                     Node C

                   Figure 5 Connection of LO ODUj (1)

   In the case of LO ODUj multiplexing into HO ODUk, Figure 6 gives an
   example of this kind of LO ODU connection.

   In Figure 6, OCh, OTUk, HO ODUk are associated with each other. The
   LO ODUj is multiplexed/de-multiplexed into/from the HO ODU at each
   ODXC node and switched at each ODXC node (i.e. trib port to line port,
   line card to line port, line port to trib port). From the viewpoint
   of connection management, the management of these HO ODUk and OTUk
   are similar to OCh. LO ODUj and OCh/OTUk/HO ODUk have client/server
   relationships. when a LO ODU connection is setup, it will be using
   the existing HO ODUk (/OTUk/OCh) connections which have been set up.
   Those HO ODUk connections provide LO ODU links, of which the LO ODU
   connection manager requests a link connection to support the LO ODU
   connection.

   For example, one HO ODU2 (/OTU2/OCh) connection can be setup between
   Node A and Node B, another HO ODU3 (/OTU3/OCh) connection can be
   setup between Node B and Node C. LO ODU1 can be generated at Node A,
   switched to one of the 10G line ports and multiplexed into a HO ODU2
   at Node A, demultiplexed from the HO ODU2 at Node B, switched at Node
   B to one of the 40G line ports and multiplexed into HO ODU3 at Node B,
   demultiplexed from HO ODU3 at Node C and switched to its LO ODU1
   terminating port at Node C.








zhang                   Expires August 2010                 [Page 22]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


       |                         LO ODUj                            |
       +----------------------------(b)-----------------------------+
       |      |  OCh/OTUk/HO ODUk  |     | OCh/OTUk/HO ODUk   |     |
       |      +--------(c)---------+     +---------(c)--------+     |
       |      |                    |     |                    |     |
      +------++-+                +--+---+--+                +-++------+
      |      |EO|                |OE|   |EO|                |OE|      |
      |      +--+----------------+--+   +--+----------------+--+      |
      |  ODXC   |                |  ODXC   |                |  ODXC   |
      +---------+                +---------+                +---------+
        Node A                     Node B                     Node C

                   Figure 6 Connection of LO ODUj (2)



 Intellectual Property

   The IETF Trust takes no position regarding the validity or scope of
   any Intellectual Property Rights or other rights that might be
   claimed to pertain to the implementation or use of the technology
   described in any IETF Document or the extent to which any license
   under such rights might or might not be available; nor does it
   represent that it has made any independent effort to identify any
   such rights.

   Copies of Intellectual Property disclosures made to the IETF
   Secretariat and any assurances of licenses to be made available, or
   the result of an attempt made to obtain a general license or
   permission for the use of such proprietary rights by implementers or
   users of this specification can be obtained from the IETF on-line IPR
   repository at http://www.ietf.org/ipr

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   any standard or specification contained in an IETF Document. Please
   address the information to the IETF at ietf-ipr@ietf.org.

   The definitive version of an IETF Document is that published by, or
   under the auspices of, the IETF. Versions of IETF Documents that are
   published by third parties, including those that are translated into
   other languages, should not be considered to be definitive versions
   of IETF Documents. The definitive version of these Legal Provisions
   is that published by, or under the auspices of, the IETF. Versions of
   these Legal Provisions that are published by third parties, including



zhang                   Expires August 2010                 [Page 23]

draft-zhang-ccamp-gmpls-g709-framework-02.txt             February 2010


   those that are translated into other languages, should not be
   considered to be definitive versions of these Legal Provisions.

   For the avoidance of doubt, each Contributor to the IETF Standards
   Process licenses each Contribution that he or she makes as part of
   the IETF Standards Process to the IETF Trust pursuant to the
   provisions of RFC 5378. No language to the contrary, or terms,
   conditions or rights that differ from or are inconsistent with the
   rights and licenses granted under RFC 5378, shall have any effect and
   shall be null and void, whether published or posted by such
   Contributor, or included with or in such Contribution.


Disclaimer of Validity

   All IETF Documents and the information contained therein are provided
   on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE
   REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE
   IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL
   WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
   WARRANTY THAT THE USE OF THE INFORMATION THEREIN WILL NOT INFRINGE
   ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
   FOR A PARTICULAR PURPOSE.


Copyright Notice


   Copyright (c) 2010 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document. Please review these documents
   carefully, as they describe your rights and restrictions with
   respect to this document.











zhang                   Expires August 2010                 [Page 24]


Html markup produced by rfcmarkup 1.107, available from http://tools.ietf.org/tools/rfcmarkup/