[Docs] [txt|pdf]

Obsoleted by: 878

     Request for Comments: 851
     Obsoletes RFC: 802
     
     
     
     
     
     
                  The ARPANET 1822L Host Access Protocol
     
     
     
                                  RFC 851
     
     
     
     
     
                              Andrew G. Malis
                       ARPANET Mail: malis@bbn-unix
     
     
     
     
     
                       Bolt Beranek and Newman Inc.
                              50 Moulton St.
                           Cambridge, MA  02238
     
     
     
     
     
                                April 1983
     
     
     
     
     
     This RFC specifies the ARPANET 1822L Host Access Protocol,  which
     is  a successor to the existing 1822 Host Access Protocol.  1822L
     allows ARPANET hosts to use  logical  names  as  well  as  1822's
     physical  port  locations to address each other.  The RFC is also
     being  presented  as  a  solicitation  of  comments   on   1822L,
     especially   from   host   network   software   implementers  and
     maintainers.
     
     
     
     
     
     
     
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
                             Table of Contents
     
     
     
     
     1   INTRODUCTION.......................................... 1
     2   THE ARPANET 1822L HOST ACCESS PROTOCOL................ 4
     2.1   Addresses and Names................................. 6
     2.2   Name Translations................................... 8
     2.2.1   Authorization and Effectiveness................... 8
     2.2.2   Translation Policies............................. 11
     2.2.3   Reporting Destination Host Downs................. 13
     2.2.4   1822L and 1822 Interoperability.................. 16
     2.3   Uncontrolled Packets............................... 18
     2.4   Establishing Host-IMP Communications............... 20
     2.5   Counting RFMS When Using 1822L..................... 22
     2.6   1822L Name Server.................................. 24
     3   1822L LEADER FORMATS................................. 27
     3.1   Host-to-IMP 1822L Leader Format.................... 28
     3.2   IMP-to-Host 1822L Leader Format.................... 35
     4   REFERENCES........................................... 43
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
                                   - i -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
                                  FIGURES
     
     
     
     
     1822 Address Format....................................... 6
     1822L Name Format......................................... 7
     1822L Address Format...................................... 7
     Communications between different host types.............. 17
     Host-to-IMP 1822L Leader Format.......................... 28
     NDM Message Format....................................... 31
     IMP-to-Host 1822L Leader Format.......................... 35
     Name Server Reply Format................................. 39
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
                                  - ii -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     1  INTRODUCTION
     
     
     This RFC specifies the ARPANET 1822L Host Access Protocol,  which
     
     will allow hosts to use logical addressing (i.e., host names that
     
     are independent of their physical location  on  the  ARPANET)  to
     
     communicate  with  each  other.  This new host access protocol is
     
     known as the ARPANET 1822L (for Logical)  Host  Access  Protocol,
     
     and  is  a  successor  to  the  current  ARPANET 1822 Host Access
     
     Protocol, which is described in  sections  3.3  and  3.4  of  BBN
     
     Report  1822  [1].   Although  the  1822L protocol uses different
     
     Host-IMP leaders than the 1822 protocol, the IMPs  will  continue
     
     to support the 1822 protocol, and hosts using either protocol can
     
     readily communicate with each other (the  IMPs  will  handle  the
     
     translation automatically).
     
     
     There is one major restriction to the  new  1822L  protocol:   it
     
     will be implemented in C/30 IMPs only, and will therefore only be
     
     usable by hosts connected to C/30 IMPs, as Honeywell and Pluribus
     
     IMPs  do  not have sufficient memory to hold the new programs and
     
     tables.  This restriction  also  means  that  logical  addressing
     
     cannot  be used to identify a host on a non-C/30 IMP.  While this
     
     is not a problem on the ARPANET, which only has  C/30  IMPs,  the
     
     restriction  will  apply  if  logical  addressing  is used on any
     
     network that mixes C/30 and non-C/30 IMPs.
     
     
     
     
     
                                   - 1 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     The RFC's terminology is consistent  with  that  used  in  Report
     
     1822, and any new terms will be defined when they are first used.
     
     Familiarity  with  Report  1822  (section  3  in  particular)  is
     
     assumed.   As could be expected, the RFC makes many references to
     
     Report 1822.  As a result, it uses, as a convenient abbreviation,
     
     "see 1822(x)" instead of "please refer to Report 1822, section x,
     
     for further details".
     
     
     This RFC updates, and obsoletes, RFC 802.  The changes from  that
     
     RFC include:
     
     
     o The Short Blocking Feature, which had also  been  described  in
     
       RFC 802, now has its own RFC, RFC 852 [2].  It was moved to its
     
       own  RFC,  since  it  is  completely  independent  of   logical
     
       addressing.
     
     
     o In section 2.2, descriptions of  the  three  address  selection
     
       policies and of host error handling have been added.
     
     
     o In section 2.3, the IMP's uncontrolled packet service has  been
     
       further  improved.  This applies to hosts using 1822 as well as
     
       1822L.
     
     
     o Pointers on using RFNM counting with 1822L have been  added  as
     
       section 2.5.
     
     
     
     
     
     
                                   - 2 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     o Section 2.6 describes the new "1822L name server" in  the  IMP,
     
       which  makes use of two new Host-to-IMP messages to allow hosts
     
       to do their own name-to-address mapping.
     
     
     o In section 3.2, the subtypes for the type  15  (1822L  Name  or
     
       Address Error) IMP-to-Host message have been changed.
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
                                   - 3 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     2  THE ARPANET 1822L HOST ACCESS PROTOCOL
     
     
     The ARPANET 1822L Host Access  Protocol  allows  a  host  to  use
     
     logical  addressing  to  communicate  with  other  hosts  on  the
     
     ARPANET.  Basically, logical addressing allows hosts to refer  to
     
     each  other  using  an  1822L  name  (see  section  2.1) which is
     
     independent of a host's physical location in  the  network.   IEN
     
     183  (also  published  as  BBN  Report 4473) [3] gives the use of
     
     logical  addressing  considerable   justification.    Among   the
     
     advantages it cites are:
     
     
     o The ability to refer to each host on  the  network  by  a  name
     
       independent of its location on the network.
     
     
     o Allowing different hosts to share  the  same  host  port  on  a
     
       time-division basis.
     
     
     o Allowing a host to use multi-homing (where a single  host  uses
     
       more than one port to communicate with the network).
     
     
     o Allowing several hosts that provide the same service  to  share
     
       the same name.
     
     
     The main differences between the 1822 and 1822L protocols are the
     
     format of the leaders that are used to introduce messages between
     
     a host and an IMP, and the specification in those leaders of  the
     
     source  and/or  destination  host(s).   Hosts  have the choice of
     
     
     
                                   - 4 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     using the 1822 or the 1822L protocol.  When a host comes up on an
     
     IMP,  it  declares  itself to be an 1822 host or an 1822L host by
     
     the type of NOP message (see section  3.1)  it  uses.   Once  up,
     
     hosts  can  switch  from  one protocol to the other by issuing an
     
     appropriate NOP.  Hosts that do not use the 1822L  protocol  will
     
     still  be  addressable by and can communicate with hosts that do,
     
     and vice-versa.
     
     
     Another difference between the two protocols  is  that  the  1822
     
     leaders are symmetric, while the 1822L leaders are not.  The term
     
     symmetric means that in the 1822 protocol, the exact same  leader
     
     format  is used for messages in both directions between the hosts
     
     and IMPs.  For example, a leader sent from a host  over  a  cable
     
     that  was  looped  back onto itself (via a looping plug or faulty
     
     hardware) would arrive back at the host and appear to be a  legal
     
     message  from  a  real host (the destination host of the original
     
     message).  In contrast, the 1822L headers are not symmetric,  and
     
     a  host  can  detect  if  the  connection to its IMP is looped by
     
     receiving a message with the wrong leader  format.   This  allows
     
     the host to take appropriate action upon detection of the loop.
     
     
     
     
     
     
     
     
     
     
     
     
                                   - 5 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     2.1  Addresses and Names
     
     
     The 1822 protocol defines one form of host specification, and the
     
     1822L  protocol  defines  two additional ways to identify network
     
     hosts.  These three forms are 1822 addresses,  1822L  names,  and
     
     1822L addresses.
     
     
     1822 addresses are  the  24-bit  host  addresses  found  in  1822
     
     leaders.  They have the following format:
     
     
     
            1              8 9                              24
           +----------------+---------------------------------+
           |                |                                 |
           |  Host number   |           IMP number            |
           |                |                                 |
           +----------------+---------------------------------+
     
                      Figure 1. 1822 Address Format
     
     
     
     These fields are quite large, and the ARPANET will never use more
     
     than  a  fraction of the available address space.  1822 addresses
     
     are used in 1822 leaders only.
     
     
     1822L names are 16-bit unsigned numbers that serve as  a  logical
     
     identifier  for  one  or  more  hosts.   1822L  names have a much
     
     simpler format:
     
     
     
     
     
     
     
     
     
                                   - 6 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     
     
     
                     1                             16
                    +--------------------------------+
                    |                                |
                    |           1822L name           |
                    |                                |
                    +--------------------------------+
     
                       Figure 2. 1822L Name Format
     
     
     
     The 1822L names are just 16-bit  unsigned  numbers,  except  that
     
     bits  1  and  2 are not both zeros (see below).  This allows over
     
     49,000 hosts to be specified.
     
     
     1822 addresses cannot be used in 1822L leaders, but there may  be
     
     a  requirement for an 1822L host to be able to address a specific
     
     physical host port or IMP fake host.  1822L  addresses  are  used
     
     for  this  function.   1822L addresses form a subset of the 1822L
     
     name space, and have both bits 1 and 2 off.
     
     
     
                    1   2  3          8 9             16
                  +---+---+------------+----------------+
                  |   |   |            |                |
                  | 0 | 0 |   host #   |   IMP number   |
                  |   |   |            |                |
                  +---+---+------------+----------------+
     
                      Figure 3. 1822L Address Format
     
     
     
     This format allows 1822L hosts to directly address hosts 0-63  at
     
     IMPs  1-255  (IMP  0 does not exist).  Note that the highest host
     
     
     
                                   - 7 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     numbers are reserved  for  addressing  the  IMP's  internal  fake
     
     hosts.   At  this  writing, the IMP has seven fake hosts, so host
     
     numbers 57-63 address the IMP fake hosts, while host numbers 0-56
     
     address  real  hosts  external  to the IMP.  As the number of IMP
     
     fake hosts changes, this boundary point will also change.
     
     
     
     
     2.2  Name Translations
     
     
     There are a number of factors that determine how an 1822L name is
     
     translated  by  the  IMP  into a physical address on the network.
     
     These factors include which translations are legal; in what order
     
     different  translations  for  the  same name should be attempted;
     
     which  legal  translations  shouldn't  be  attempted  because   a
     
     particular  host  port  is down; and the interoperability between
     
     1822  and  1822L  hosts.   These  issues  are  discussed  in  the
     
     following sections.
     
     
     
     
     2.2.1  Authorization and Effectiveness
     
     
     Every host on a C/30 IMP, regardless of whether it is  using  the
     
     1822  or  1822L  protocol  to access the network, can have one or
     
     more 1822L names (logical addresses).  Hosts using 1822L can then
     
     use  these  names to address the hosts in the network independent
     
     of their  physical  locations.   Because  of  the  implementation
     
     
     
                                   - 8 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     constraints mentioned in the introduction, hosts on non-C/30 IMPs
     
     cannot be assigned 1822L names.  To circumvent this  restriction,
     
     however,  1822L  hosts can also use 1822L addresses to access all
     
     of the other hosts.
     
     
     At this point, several questions  arise:   How  are  these  names
     
     assigned,  how  do  they  become  known  to  the  IMPs  (so  that
     
     translations to physical addresses can be made), and how  do  the
     
     IMPs know which host is currently using a shared port?  To answer
     
     each question in order:
     
     
     Names are assigned by a central network administrator.  When each
     
     name  is  created, it is assigned to a host (or a group of hosts)
     
     at one or more specific host ports.  The host(s) are  allowed  to
     
     reside at those specific host ports, and nowhere else.  If a host
     
     moves, it will keep the same name, but the administrator  has  to
     
     update  the  central  database  to  reflect  the  new  host port.
     
     Changes to this database are  distributed  to  the  IMPs  by  the
     
     Network  Operations  Center  (NOC).  For a while, the host may be
     
     allowed to reside at either of (or both) the new and  old  ports.
     
     Once  the  correspondence  between  a  name and one or more hosts
     
     ports where it  may  be  used  has  been  made  official  by  the
     
     administrator,   that  name  is  said  to  be  authorized.  1822L
     
     addresses, which actually  refer  to  physical  host  ports,  are
     
     always authorized in this sense.
     
     
     
                                   - 9 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     Once a host has been assigned one or more names, it  has  to  let
     
     the  IMPs  know  where it is and what name(s) it is using.  There
     
     are two cases to consider, one for 1822L hosts  and  another  for
     
     1822  hosts.   The following discussion only pertains to hosts on
     
     C/30 IMPs.
     
     
     When an IMP sees an 1822L host come up on a host  port,  the  IMP
     
     has  no way of knowing which host has just come up (several hosts
     
     may share the same port, or one host may prefer to  be  known  by
     
     different  names  at different times).  This requires the host to
     
     declare itself to the IMP before it can actually send and receive
     
     messages.   This  function  is  performed  by  a  new host-to-IMP
     
     message, the Name Declaration  Message  (NDM),  which  lists  the
     
     names  that  the  host would like to be known by.  The IMP checks
     
     its tables to see if each of the names is authorized,  and  sends
     
     an  NDM  Reply  to  the  host  saying  which  names were actually
     
     authorized and can now be used for sending and receiving messages
     
     (i.e.,  which  names  are  effective). A host can also use an NDM
     
     message to change its list of effective names (it can add to  and
     
     delete  from  the  list) at any time.  The only constraint on the
     
     host is that any names it wishes to use can become effective only
     
     if they are authorized.
     
     
     In the second case, if a host comes up on a C/30  IMP  using  the
     
     1822 protocol, the IMP automatically makes the first name the IMP
     
     
     
                                  - 10 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     finds in its tables for that host become effective.   Thus,  even
     
     though  the host is using the 1822 protocol, it can still receive
     
     messages from 1822L hosts via its 1822L name.  Of course, it  can
     
     also receive messages from an 1822L host via its 1822L address as
     
     well.   (Remember,  the  distinction  between  1822L  names   and
     
     addresses  is that the addresses correspond to physical locations
     
     on  the  network,  while   the   names   are   strictly   logical
     
     identifiers).   The  IMPs translate between the different leaders
     
     and send the proper leader in each case (see section 2.2.4).
     
     
     The third question above has by now already been answered.   When
     
     an  1822L  host comes up, it uses the NDM message to tell the IMP
     
     which host it is (which names it is known by).  Even if this is a
     
     shared port, the IMP knows which host is currently connected.
     
     
     Whenever a host goes down, its names  automatically  become  non-
     
     effective.   When it comes back up, it has to make them effective
     
     again.
     
     
     
     
     2.2.2  Translation Policies
     
     
     Several hosts can share the same 1822L name.  If more than one of
     
     these  hosts  is  up  at the same time, any messages sent to that
     
     1822L name will be delivered to just one  of  the  hosts  sharing
     
     that  name,  and  a RFNM will be returned as usual.  However, the
     
     
     
                                  - 11 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     sending host will  not  receive  any  indication  of  which  host
     
     received  the  message,  and subsequent messages to that name are
     
     not guaranteed to be sent to the  same  host.   Typically,  hosts
     
     providing  exactly  the  same  service could share the same 1822L
     
     name in this manner.
     
     
     Similarly, when a host is multi-homed, the same  1822L  name  may
     
     refer  to  more  than  one  host  port (all connected to the same
     
     host).  If the host is up on only one of those ports,  that  port
     
     will be used for all messages addressed to the host.  However, if
     
     the host were up on more than one  port,  the  message  would  be
     
     delivered  over  just  one  of  those ports, and the subnet would
     
     choose which port to use.  This port selection could change  from
     
     message  to  message.   If  a  host wanted to insure that certain
     
     messages were delivered to it on specific ports,  these  messages
     
     could  use  either  the  port's 1822L address or a specific 1822L
     
     name that referred to that port alone.
     
     
     Three different address selection policies are available for  the
     
     name mapping process.  When translated, each name uses one of the
     
     three policies  (the  policy  is  pre-determined  on  a  per-name
     
     basis).  The three policies are:
     
     
     o  Attempt each translation in the order in  which  the  physical
     
        addresses  are listed in the IMP's translation tables, to find
     
     
     
     
                                  - 12 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
        the first reachable  physical  host  address.   This  list  is
     
        always  searched  from the top whenever an uncontrolled packet
     
        is to be sent or an end-to-end connection has to  be  created.
     
        This is the most commonly used policy.
     
     
     o  Selection of the closest  physical  address,  which  uses  the
     
        IMP's   routing   tables   to  find  the  translation  to  the
     
        destination IMP with the least delay path.
     
     
     o  Use load leveling. This is similar to the second  policy,  but
     
        differs  in  that  searching  the  address  list  for  a valid
     
        translation starts at the address following where the previous
     
        translation  search  ended.   This  attempts to spread out the
     
        load from any one  IMP's  hosts  to  the  various  host  ports
     
        associated  with  a  particular  name.   Note that this is NOT
     
        network-wide load leveling, which would require a  distributed
     
        algorithm and tables.
     
     
     
     
     2.2.3  Reporting Destination Host Downs
     
     
     As was explained in report 1822, and  as  will  be  discussed  in
     
     greater detail in section 2.5, whenever regular messages are sent
     
     by a  host,  the  IMP  opens  a  subnetwork  connection  to  each
     
     destination  host  from  the source host.  A connection will stay
     
     open at least as long as there are  any  outstanding  (un-RFNMed)
     
     
     
                                  - 13 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     messages  using it and both the source and destination hosts stay
     
     up.
     
     
     However, the destination host may go down for some reason  during
     
     the  lifetime of a connection.  If the host goes down while there
     
     are no outstanding messages  to  it  in  the  network,  then  the
     
     connection  is  closed  and  no  other  action is taken until the
     
     source host submits the next message for  that  destination.   At
     
     that time, ONE of the following events will occur:
     
     A1.  If 1822 or an 1822L address is being  used  to  specify  the
     
          destination host, then the source host will receive a type 7
     
          (Destination Host Dead) message from the IMP.
     
     A2.  If an 1822L name is being used to  specify  the  destination
     
          host,  and  the  name maps to only one authorized host port,
     
          then a type 7 message will also be sent to the source host.
     
     A3.  If an 1822L name is being used to  specify  the  destination
     
          host,  and  the  name  maps to more than one authorized host
     
          port, then the IMP attempts to open a connection to  another
     
          authorized  and  effective  host  port for that name.  If no
     
          such connection can be made, the host will receive a type 15
     
          (1822L  Name  or  Address  Error),  subtype  5 (no effective
     
          translations) message (see section 3.2).  Note that a type 7
     
          message  cannot be returned to the source host, since type 7
     
          messages refer to a particular destination  host  port,  and
     
     
     
     
                                  - 14 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
          the name maps to more than one destination port.
     
     
     Things get a bit more complicated if there  are  any  outstanding
     
     messages  on  the connection when the destination host goes down.
     
     The connection will be closed, and  one  of  the  following  will
     
     occur:
     
     B1.  If 1822 or an 1822L address is being  used  to  specify  the
     
          destination host, then the source host will receive a type 7
     
          message for each outstanding message.
     
     B2.  If an 1822L name is being used to  specify  the  destination
     
          host, then the source host will receive a type 9 (Incomplete
     
          Transmission),  subtype  3  (message  lost  due  to  network
     
          failure)  message  for  each  outstanding message.  The next
     
          time the source host submits another message for  that  same
     
          destination  name,  the  previous  algorithm  will  be  used
     
          (either step A2 or step A3).
     
     
     The above two algorithms also apply when a  host  stays  up,  but
     
     declares  the  destination  name for an existing connection to no
     
     longer be effective.  In this case, however, the type 7  messages
     
     above will be replaced by type 15, subtype 3 (name not effective)
     
     messages.
     
     
     Section 2.3 discusses how destination host downs are handled  for
     
     uncontrolled packets.
     
     
     
     
                                  - 15 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     2.2.4  1822L and 1822 Interoperability
     
     
     As  has  been  previously  stated,  1822  and  1822L  hosts   can
     
     intercommunicate,  and  the  IMPs  will  automatically handle any
     
     necessary leader and address format  conversions.   However,  not
     
     every   combination   of   1822   and  1822L  hosts  allows  full
     
     interoperability with regard to the use of 1822L names.
     
     
     The   following   figure   illustrates   how   these   addressing
     
     combinations  are  handled,  showing  how  each  type of host can
     
     access every other type of host.  There are three types of hosts:
     
     "1822  on  C/30"  signifies  an  1822 host that is on a C/30 IMP,
     
     "1822L" signifies an 1822L host (on a C/30  IMP),  and  "1822  on
     
     non-C/30"  signifies  a  host  on  an  non-C/30 IMP (which cannot
     
     support the 1822L protocol).  The table entry shows the  protocol
     
     and  host address format(s) that the source host can use to reach
     
     the destination host.
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
                                  - 16 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     
     
     
                                 Destination Host
       Source
       Host    | 1822 on C/30   | 1822L          | 1822 on non-C/30
       --------+----------------+----------------+-----------------
               |                |                |
       1822 on | 1822           | 1822           | 1822
       C/30    |                | (note 1)       |
               |                |                |
       --------+----------------+----------------+-----------------
               |                |                |
               | 1822L, using   | 1822L, using   | 1822L, using
       1822L   | 1822L name or  | 1822L name or  | 1822L address
               |address (note 2)| address        | only (note 2)
               |                |                |
       --------+----------------+----------------+-----------------
               |                |                |
       1822 on | 1822           | 1822           | 1822
       non-C/30|                | (note 1)       |
               |                |                |
       --------+----------------+----------------+-----------------
     
       Note 1: The message is presented  to  the  destination  host
               with  an 1822L leader containing the 1822L addresses
               of the source  and  destination  hosts.   If  either
               address  cannot be encoded as an 1822L address, then
               the message is not delivered and an error message is
               sent to the source host.
     
       Note 2: The message is presented  to  the  destination  host
               with  an  1822 leader containing the 1822 address of
               the source host.
     
     
          Figure 4. Communications between different host types
     
     
     
     
     
     
     
     
     
     
     
     
     
                                  - 17 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     2.3  Uncontrolled Packets
     
     
     Uncontrolled packets (see 1822(3.6)) present a unique problem for
     
     the  1822L protocol.  Uncontrolled packets use none of the normal
     
     ordering and error-control mechanisms in the IMP, and do not  use
     
     the  normal  subnetwork  connection  facilities.   As  a  result,
     
     uncontrolled packets need to carry all  of  their  overhead  with
     
     them, including source and destination names.  If 1822L names are
     
     used when sending an uncontrolled packet, additional  information
     
     is  now required by the subnetwork when the packet is transferred
     
     to the destination IMP.  This means that less  host-to-host  data
     
     can  be  contained  in  the  packet than is possible between 1822
     
     hosts.
     
     
     Uncontrolled packets that are sent between 1822 hosts may contain
     
     not  more  than  991 bits of data.  Uncontrolled packets that are
     
     sent to and/or from 1822L hosts are limited to 32 bits  less,  or
     
     not  more  than  959  bits.  Packets that exceed this length will
     
     result in an error indication to the host, and  the  packet  will
     
     not  be sent.  This error indication represents an enhancement to
     
     the previous level of service provided by the  IMP,  which  would
     
     simply   discard  an  overly  long  uncontrolled  packet  without
     
     notification.
     
     
     
     
     
     
     
                                  - 18 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     Other enhancements that  are  provided  for  uncontrolled  packet
     
     service  are  a  notification  to the host of any errors that are
     
     detected by the host's IMP when it receives the packet.   A  host
     
     will  be  notified if an uncontrolled packet contains an error in
     
     the 1822L  name  specification,  such  as  if  the  name  is  not
     
     authorized or effective, if the remote host is unreachable (which
     
     is indicated by none of its names being  effective),  if  network
     
     congestion control throttled the packet before it left the source
     
     IMP, or for any other reason the source IMP was not able to  send
     
     the packet on its way.
     
     
     In most cases, the host will not be notified if the  uncontrolled
     
     packet  was  lost  once  it  was  transmitted  by the source IMP.
     
     However, the IMP will attempt to notify  the  source  host  if  a
     
     logically-addressed  uncontrolled packet was mistakenly sent to a
     
     host that the source IMP thought was effective, but which  turned
     
     out  to  be  dead  or non-effective at the destination IMP.  This
     
     non-delivery notice  is  sent  back  to  the  source  IMP  as  an
     
     uncontrolled  packet from the destination IMP, so the source host
     
     is not guaranteed to receive this indication.
     
     
     If the source IMP successfully receives the non-delivery  notice,
     
     then  the  source  host  will  receive  a  type 15 (1822L Name or
     
     Address Error), subtype 6 (down or non-effective  port)  message.
     
     If  the  packet  is  resubmitted or another packet is sent to the
     
     
     
                                  - 19 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     same destination name,  and  there  are  no  available  effective
     
     translations,  then  the  source  host  will  receive  a type 15,
     
     subtype 5 (no effective translations) message if the  destination
     
     name  has  more than one mapping; or will receive either a type 7
     
     (Destination Host Dead)  or  a  type  15,  subtype  3  (name  not
     
     effective)   message   if  the  destination  name  has  a  single
     
     translation.
     
     
     Those enhancements to the uncontrolled packet  service  that  are
     
     not  specific  to  logical  addressing will be available to hosts
     
     using  1822  as  well  as  1822L.   However,  logically-addressed
     
     uncontrolled  packets  must  be  used  in  order  to  receive any
     
     indication that the packet was lost once it has left  the  source
     
     IMP.
     
     
     
     
     2.4  Establishing Host-IMP Communications
     
     
     When a host comes up on an IMP, or after there has been  a  break
     
     in   the  communications  between  the  host  and  its  IMP  (see
     
     1822(3.2)), the orderly flow of messages between the host and the
     
     IMP  needs  to  be properly (re)established.  This allows the IMP
     
     and host to recover from most any failure  in  the  other  or  in
     
     their communications path, including a break in mid-message.
     
     
     
     
     
     
                                  - 20 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     The first messages that a host should send to its IMP  are  three
     
     NOP  messages.   Three  messages  are  required to insure that at
     
     least one message will be properly read by the IMP (the first NOP
     
     could be concatenated to a previous message if communications had
     
     been broken in mid-stream, and the third provides redundancy  for
     
     the   second).    These   NOPs   serve  several  functions:  they
     
     synchronize the IMP with the host, they tell  the  IMP  how  much
     
     padding  the  host  requires  between  the message leader and its
     
     body, and they also tell the IMP whether the host will  be  using
     
     1822 or 1822L leaders.
     
     
     Similarly, the IMP will send three  NOPs  to  the  host  when  it
     
     detects  that  the host has come up.  Actually, the IMP will send
     
     six NOPs, alternating three 1822  NOPs  with  three  1822L  NOPs.
     
     Thus, the host will see three NOPs no matter which protocol it is
     
     using.   The  NOPs  will  be  followed  by  two  Interface  Reset
     
     messages,  one of each style.  If the IMP receives a NOP from the
     
     host while the above sequence is occurring,  the  IMP  will  only
     
     send  the  remainder  of  the NOPs and the Interface Reset in the
     
     proper style.  The 1822 NOPs will contain the 1822 address of the
     
     host interface, and the 1822L NOPs will contain the corresponding
     
     1822L address.
     
     
     Once the IMP  and  the  host  have  sent  each  other  the  above
     
     messages, regular communications can commence.  See 1822(3.2) for
     
     
     
                                  - 21 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     further details concerning the ready line,  host  tardiness,  and
     
     other issues.
     
     
     
     
     2.5  Counting RFMS When Using 1822L
     
     
     When a host submits a regular message using an 1822  leader,  the
     
     IMP  checks  for  an  existing simplex virtual circuit connection
     
     from the  source  host  to  the  destination  host.   If  such  a
     
     connection   already  exists,  it  is  used.   Otherwise,  a  new
     
     connection from the source host port to the destination host port
     
     is  opened.   In either case, there may be at most eight messages
     
     outstanding on that connection  at  any  one  time.   If  a  host
     
     submits  a  ninth message on that connection before it receives a
     
     reply for the first message, then the host will be blocked  until
     
     the reply is sent for the first message.
     
     
     Such connections can stay open for some time, but are  timed  out
     
     after  three minutes of no activity, or can be closed if there is
     
     contention for the connection blocks  in  either  the  source  or
     
     destination  IMP.   However, a connection will never be closed as
     
     long as there are any outstanding messages on it.  This allows  a
     
     source  host  to  count the number of replies it has received for
     
     messages to each destination host address in order to avoid being
     
     blocked   by  submitting  a  ninth  outstanding  message  on  any
     
     
     
     
                                  - 22 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     connection.
     
     
     When a host submits a regular message using an  1822L  leader,  a
     
     similar process occurs, except that in this case, connections are
     
     distinguished by the source  name/destination  name  combination.
     
     When the message is received from a host, the IMP first looks for
     
     an open connection for that  same  source  name/destination  name
     
     pair.   If  such  a  connection is found, then it is used, and no
     
     further name translation is  performed.   If,  however,  no  open
     
     connection  was  found,  then the destination name is translated,
     
     and a connection opened to the physical host port.   As  long  as
     
     there are any outstanding messages on the connection it will stay
     
     open, and it will have  the  same  restriction  that  only  eight
     
     messages may be outstanding at any one time.  Thus, a source host
     
     can still count replies to avoid being blocked, but they must  be
     
     counted  on a source name/destination name pair basis, instead of
     
     just by destination host address as before.
     
     
     Since connections are based on the source name  as  well  as  the
     
     destination  name,  this  implies that there may be more than one
     
     open connection from physical host port A to physical  host  port
     
     B,   which   would   allow   more  than  8  outstanding  messages
     
     simultaneously from the first to the second port.   However,  for
     
     this  to  occur, either the source or destination names, or both,
     
     must differ from one connection to the next.  For example, if the
     
     
     
                                  - 23 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     names  "543"  and  "677" both translate to physical port 3 on IMP
     
     51, then the host on that port could  open  four  connections  to
     
     itself  by  sending  messages  from "543" to "543", from "543" to
     
     "677", from "677" to "543", and from "677" to "677".
     
     
     As has already been stated,  the  destination  names  in  regular
     
     messages  are  only translated when connections are first opened.
     
     Once a connection is open, that connection, and  its  destination
     
     physical  host port, will continue to be used until it is closed.
     
     If, in the meantime, a "better" destination host  port  belonging
     
     to  the  same  destination name became available, it would not be
     
     used until the next time a  new  connection  is  opened  to  that
     
     destination name.
     
     
     
     
     2.6  1822L Name Server
     
     
     There may  be  times  when  a  host  wants  to  perform  its  own
     
     translations,  or  might need the full list of physical addresses
     
     to which a particular name maps.  For example, a connection-based
     
     host-to-host  protocol  may  require  that the same physical host
     
     port on a multi-homed host be used for all  messages  using  that
     
     host-to-host  connection, and the host does not wish to trust the
     
     IMP to always deliver messages using a destination  name  to  the
     
     same host port.
     
     
     
     
                                  - 24 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     In these cases, the host  can  submit  a  type  11  (Name  Server
     
     Request)  message to the IMP, which requests the IMP to translate
     
     the destination 1822L name and return a list of the addresses  to
     
     which  it maps.  The IMP will respond with a type 11 (Name Server
     
     Reply) message, which contains the selection policy  in  use  for
     
     that  name,  the  number of addresses to which the name maps, the
     
     addresses  themselves,  and  for  each  address,  whether  it  is
     
     effective and its routing distance from the IMP.  See section 3.2
     
     for a complete description of the message's contents.
     
     
     Using this information, the source  host  can  make  an  informed
     
     decision  on which of the physical host ports corresponding to an
     
     1822L name to use, and can subsequently send the messages to that
     
     port, rather than to the name.
     
     
     The IMP also supports a different type of name service.   A  host
     
     needs  to issue a Name Declaration Message to the IMP in order to
     
     make its names effective, but it may not wish to keep  its  names
     
     in  some table or file in the host.  In this case, it can ask the
     
     IMP to tell it which names it is authorized to use.
     
     
     In this case, the host submits a  type  12  (Port  List  Request)
     
     message to the IMP, and the IMP replies with a type 12 (Port List
     
     Reply) message.  It contains, for the host port  over  which  the
     
     IMP  received the request and sent the reply, the number of names
     
     
     
     
                                  - 25 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     that map to the port, the list of names, and whether or not  each
     
     name  is  effective.   The  host can then use this information in
     
     order  to  issue  the  Name  Declaration  Message.   Section  3.2
     
     contains a complete description of the reply's contents.
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
                                  - 26 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     3  1822L LEADER FORMATS
     
     
     The following sections describe the formats of the  leaders  that
     
     precede  messages  between  an 1822L host and its IMP.  They were
     
     designed to be as compatible with the 1822 leaders  as  possible.
     
     The  second,  fifth,  and  sixth  words  are identical in the two
     
     leaders, and all  of  the  existing  functionality  of  the  1822
     
     leaders  has  been  retained.   In  the  first word, the 1822 New
     
     Format Flag is now also used to identify the two types  of  1822L
     
     leaders, and the Handling Type has been moved to the second byte.
     
     The third and fourth words contain  the  Source  and  Destination
     
     1822L Name, respectively.
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
                                  - 27 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     3.1  Host-to-IMP 1822L Leader Format
     
     
     
     
     
                    1      4 5      8 9             16
                   +--------+--------+----------------+
                   |        |  1822L |                |
                   | Unused |  H2I   | Handling Type  |
                   |        |  Flag  |                |
                   +--------+--------+----------------+
                    17    20 21 22 24 25            32
                   +--------+-+------+----------------+
                   |        |T|Leader|                |
                   | Unused |R|Flags |  Message Type  |
                   |        |C|      |                |
                   +--------+-+------+----------------+
                    33                              48
                   +----------------------------------+
                   |                                  |
                   |           Source Host            |
                   |                                  |
                   +----------------------------------+
                    49                              64
                   +----------------------------------+
                   |                                  |
                   |         Destination Host         |
                   |                                  |
                   +----------------------------------+
                    65                     76 77    80
                   +-------------------------+--------+
                   |                         |        |
                   |       Message ID        |Sub-type|
                   |                         |        |
                   +-------------------------+--------+
                    81                              96
                   +----------------------------------+
                   |                                  |
                   |              Unused              |
                   |                                  |
                   +----------------------------------+
     
                Figure 5. Host-to-IMP 1822L Leader Format
     
     
     
     
     
     
                                  - 28 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     Bits 1-4: Unused, must be set to zero.
     
     
     Bits 5-8: 1822L Host-to-IMP Flag:
     
          This field is set to decimal 13 (1101 in binary).
     
     
     Bits 9-16: Handling Type:
     
          This  field  is  bit-coded  to  indicate  the   transmission
     
          characteristics  of  the connection desired by the host. See
     
          1822(3.3).
     
          Bit 9: Priority Bit:
     
               Messages with this bit on will be treated  as  priority
     
               messages.
     
          Bits 10-16: Unused, must be zero.
     
     
     Bits 17-20: Unused, must be zero.
     
     
     Bit 21: Trace Bit:
     
          If equal to one, this message is designated for  tracing  as
     
          it proceeds through the network.  See 1822(5.5).
     
     
     Bits 22-24: Leader Flags:
     
          Bit 22: A flag available for use by  the  destination  host.
     
               See 1822(3.3) for a description of its use by the IMP's
     
               TTY Fake Host.
     
          Bits 23-24: Reserved for future use, must be zero.
     
     
     
     
     
     
                                  - 29 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     Bits 25-32: Message Type:
     
          Type 0: Regular Message  -  All  host-to-host  communication
     
               occurs  via  regular  messages, which have several sub-
     
               types, found in bits 77-80.  These sub-types are:
     
               0: Standard - The IMP uses its full message  and  error
     
                    control facilities, and host blocking may occur.
     
               3: Uncontrolled  Packet  -  The  IMP  will  perform  no
     
                    message-control   functions   for   this  type  of
     
                    message, and network flow and  congestion  control
     
                    may  cause loss of the packet.  Also see 1822(3.6)
     
                    and section 2.3.
     
               4-15: Unassigned.
     
          Type 1: Error Without Message ID - See 1822(3.3).
     
          Type 2: Host Going Down - see 1822(3.3).
     
          Type 3: Name Declaration Message (NDM)  -  This  message  is
     
               used by the host to declare which of its 1822L names is
     
               or is not effective (see section 2.2.1), or to make all
     
               of  its  names non-effective.  The first 16 bits of the
     
               data portion of the NDM message, following  the  leader
     
               and  any  leader  padding, contains the number of 1822L
     
               names contained in the message.  This  is  followed  by
     
               the 1822L name entries, each 32 bits long, of which the
     
               first 16 bits is a 1822L name and the  second  16  bits
     
               contains  either  of  the  integers  zero or one.  Zero
     
     
     
                                  - 30 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
               indicates that the name should not  be  effective,  and
     
               one  indicates  that the name should be effective.  The
     
               IMP will reply with a NDM Reply  message  (see  section
     
               3.2)  indicating  which  of the names are now effective
     
               and which are not.  Pictorially, a NDM message has  the
     
               following   format  (including  the  leader,  which  is
     
               printed in hexadecimal):
     
     
     
     
                 1             16 17            32 33            48
                +----------------+----------------+----------------+
                |                |                |                |
                |      0D00      |      0003      |      0000      |
                |                |                |                |
                +----------------+----------------+----------------+
                 49            64 65            80 81            96
                +----------------+----------------+----------------+
                |                |                |                |
                |      0000      |      0000      |      0000      |
                |                |                |                |
                +----------------+----------------+----------------+
                 97           112 113          128 129          144
                +----------------+----------------+----------------+
                |                |                |                |
                |  # of entries  |  1822L name #1 |     0 or 1     |
                |                |                |                |
                +----------------+----------------+----------------+
                145           160 161          176
                +----------------+----------------+
                |                |                |
                |  1822L name #2 |     0 or 1     |       etc.
                |                |                |
                +----------------+----------------+
     
                       Figure 6. NDM Message Format
     
     
     
     
     
     
     
                                  - 31 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
               An  NDM  with  zero  entries  will  cause  all  current
     
               effective names for the host to become non-effective.
     
          Type 4: NOP - This allows the IMP to  know  which  style  of
     
               leader  the  host wishes to use.  A 1822L NOP signifies
     
               that the host wishes to use 1822L leaders, and an  1822
     
               NOP signifies that the host wishes to use 1822 leaders.
     
               All of the other remarks concerning the NOP message  in
     
               1822(3.3)  still  hold.   The  host should always issue
     
               NOPs in groups of three to insure proper  reception  by
     
               the IMP.  Also see section 2.4 for a further discussion
     
               on the use of the NOP message.
     
          Type 8: Error with Message ID - see 1822(3.3).
     
          Type 11: Name Server Request - This allows the host  to  use
     
               the  IMP's  logical addressing tables as a name server.
     
               The destination name in the 1822L leader is translated,
     
               and  the  IMP replies with a Name Server Reply message,
     
               which lists the physical host addresses  to  which  the
     
               destination name maps.
     
          Type 12: Port List Request - This allows the  physical  host
     
               to  request the list of names that map to the host port
     
               over which this request was received by the  IMP.   The
     
               IMP replies with a Port List Reply message, which lists
     
               the names that map to the port.
     
          Types 5-7,9-10,13-255: Unassigned.
     
     
     
                                  - 32 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     Bits 33-48: Source Host:
     
          This field contains one of the  source  host's  1822L  names
     
          (or,  alternatively,  the 1822L address of the host port the
     
          message  is  being  sent   over).    This   field   is   not
     
          automatically filled in by the IMP, as in the 1822 protocol,
     
          because the host may be known by several names and may  wish
     
          to use a particular name as the source of this message.  All
     
          messages from the same host need not use the  same  name  in
     
          this  field.   Each  source  name, when used, is checked for
     
          authorization, effectiveness, and actually belonging to this
     
          host.  Messages using names that do not satisfy all of these
     
          requirements will not be delivered, and will instead  result
     
          in  an  error  message being sent back into the source host.
     
          If the host places its 1822L  address  in  this  field,  the
     
          address is checked to insure that it actually represents the
     
          host port where the message originated.  If the  message  is
     
          destined for an 1822 host on a non-C/30 IMP, this field MUST
     
          contain the source host's 1822L address  (see  figure  4  in
     
          section 2.2.4).
     
     
     Bits 49-64: Destination Host:
     
          This field  contains  the  1822L  name  or  address  of  the
     
          destination  host.   If it contains a name, the name will be
     
          checked for effectiveness, with an error message returned to
     
     
     
     
                                  - 33 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
          the  source  host  if  the  name  is  not effective.  If the
     
          message is destined for an 1822 host on a non-C/30 IMP, this
     
          field MUST contain the destination host's 1822L address (see
     
          figure 4 in section 2.2.4).
     
     
     Bits 65-76: Message ID:
     
          This is a host-specified identification used in all  type  0
     
          and  type  8  messages, and is also used in type 2 messages.
     
          When used in type 0 messages, bits 65-72 are also  known  as
     
          the  Link  Field,  and  should  contain  values specified in
     
          Assigned  Numbers  [4]  appropriate  for  the   host-to-host
     
          protocol being used.
     
     
     Bits 77-80: Sub-type:
     
          This field is used as a modifier by message types 0,  2,  4,
     
          and 8.
     
     
     Bits 81-96: Unused, must be zero.
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
                                  - 34 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     3.2  IMP-to-Host 1822L Leader Format
     
     
     
     
     
                    1      4 5      8 9             16
                   +--------+--------+----------------+
                   |        |  1822L |                |
                   | Unused |  I2H   | Handling Type  |
                   |        |  Flag  |                |
                   +--------+--------+----------------+
                    17    20 21 22 24 25            32
                   +--------+-+------+----------------+
                   |        |T|Leader|                |
                   | Unused |R|Flags |  Message Type  |
                   |        |C|      |                |
                   +--------+-+------+----------------+
                    33                              48
                   +----------------------------------+
                   |                                  |
                   |           Source Host            |
                   |                                  |
                   +----------------------------------+
                    49                              64
                   +----------------------------------+
                   |                                  |
                   |         Destination Host         |
                   |                                  |
                   +----------------------------------+
                    65                     76 77    80
                   +-------------------------+--------+
                   |                         |        |
                   |       Message ID        |Sub-type|
                   |                         |        |
                   +-------------------------+--------+
                    81                              96
                   +----------------------------------+
                   |                                  |
                   |          Message Length          |
                   |                                  |
                   +----------------------------------+
     
                Figure 7. IMP-to-Host 1822L Leader Format
     
     
     
     
     
     
                                  - 35 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     Bits 1-4: Unused and set to zero.
     
     
     Bits 5-8: 1822L IMP-to-Host Flag:
     
          This field is set to decimal 14 (1110 in binary).
     
     
     Bits 9-16: Handling Type:
     
          This has the value assigned by the source host (see  section
     
          3.1).   This field is only used in message types 0, 5-9, and
     
          15.
     
     
     Bits 17-20: Unused and set to zero.
     
     
     Bit 21: Trace Bit:
     
          If equal to one, the source host designated this message for
     
          tracing as it proceeds through the network.  See 1822(5.5).
     
     
     Bits 22-24: Leader Flags:
     
          Bit 22: Available as a destination host flag.
     
          Bits 23-24: Reserved for future use, set to zero.
     
     
     Bits 25-32: Message Type:
     
          Type 0: Regular Message  -  All  host-to-host  communication
     
               occurs  via  regular  messages, which have several sub-
     
               types.  The sub-type field (bits 77-80) is the same  as
     
               sent in the host-to-IMP leader (see section 3.1).
     
          Type 1: Error in Leader - See 1822(3.4).
     
          Type 2: IMP Going Down - See 1822(3.4).
     
     
     
                                  - 36 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
          Type 3: NDM Reply - This is a reply to the  NDM  host-to-IMP
     
               message  (see  section  3.1).   It  will  have the same
     
               number of entries as the  NDM  message  that  is  being
     
               replying  to,  and  each  listed  1822L  name  will  be
     
               accompanied by a zero or a one (see figure 6).  A  zero
     
               signifies  that  the  name  is not effective, and a one
     
               means that the name is now effective.
     
          Type 4: NOP - The host should discard this message.   It  is
     
               used    during    initialization    of   the   IMP/host
     
               communication.  The Destination Host field will contain
     
               the  1822L  Address of the host port over which the NOP
     
               is being sent.  All other fields are unused.
     
          Type 5: Ready for Next Message (RFNM) - See 1822(3.4).
     
          Type 6: Dead Host Status - See 1822(3.4).
     
          Type 7: Destination Host or IMP  Dead  (or  unknown)  -  See
     
               1822(3.4).
     
          Type 8: Error in Data - See 1822(3.4).
     
          Type 9: Incomplete Transmission - See 1822(3.4).
     
          Type 10: Interface Reset - See 1822(3.4).
     
          Type 11: Name Server Reply - This reply to the  Name  Server
     
               Request  host-to-IMP  message  contains a word with the
     
               selection policy and the number of  physical  addresses
     
               to  which  the  destination  name maps, followed by two
     
               words per physical address: the first word contains  an
     
     
     
                                  - 37 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
               1822L  address,  and  the  second  word  contains a bit
     
               signifying whether or not that  particular  translation
     
               is effective and the routing distance (in 6.4 ms units)
     
               to the address's IMP.   In  figure  8,  EFF  is  1  for
     
               effective and 0 for non-effective, and POL is a two-bit
     
               number indicating the selection  policy  for  the  name
     
               (see section 2.2.2):
     
               0: First reachable.
     
               1: Closest physical address.
     
               2: Load leveling.
     
               3: Unused.
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
                                  - 38 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     
     
     
                 1             16 17            32 33            48
                +----------------+----------------+----------------+
                |                |                |                |
                |      0E00      |      000B      |      0000      |
                |                |                |                |
                +----------------+----------------+----------------+
                 49            64 65            80 81            96
                +----------------+----------------+----------------+
                |                |                |                |
                |   dest. name   |      0000      |      0000      |
                |                |                |                |
                +----------------+----------------+----------------+
                 97           112 113          128 129          144
                +-+--------------+----------------+-+--------------+
                |P|              |                |E|              |
                |O|  # of addrs  |  1822L addr #1 |F| routing dist |
                |L|              |                |F|              |
                +-+--------------+----------------+-+--------------+
                145           160 161          176
                +----------------+-+--------------+
                |                |E|              |
                |  1822L addr #2 |F| routine dist |       etc.
                |                |F|              |
                +----------------+-+--------------+
     
                    Figure 8. Name Server Reply Format
     
     
     
          Type 12: Port List Reply - This is the  reply  to  the  Port
     
               List  Request  host-to-IMP  message.   It  contains the
     
               number of names that map to this  physical  host  port,
     
               followed by two words per name: the first word contains
     
               an 1822L name that maps to this port,  and  the  second
     
               contains  either a zero or a one, signifying whether or
     
               not that  particular  translation  is  effective.   The
     
               format  is  identical  to  the type 3 NDM Reply message
     
     
     
                                  - 39 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
               (see figure 6).
     
          Type 15: 1822L Name or Address Error - This message is  sent
     
               in  response  to  a  type  0  message  from a host that
     
               contained an erroneous Source Host or Destination  Host
     
               field.  Its sub-types are:
     
               0: The Source Host 1822L name is not authorized or  not
     
                    effective.
     
               1: The Source Host 1822L address  does  not  match  the
     
                    host port used to send the message.
     
               2: The Destination Host 1822L name is not authorized.
     
               3:  The  physical  host  to  which  this   singly-homed
     
                    Destination Host name translated is authorized and
     
                    up, but not effective.  If the host  was  actually
     
                    down,  a  type  7 message would be returned, not a
     
                    type 15.
     
               4: The Source or  Destination  Host  field  contains  a
     
                    1822L  name,  but the host being addressed is on a
     
                    non-C/30 IMP (see figure 4 in section 2.2.4).
     
               5: The multi-homed Destination Host name is authorized,
     
                    but has no available effective translations.
     
               6: A logically-addressed uncontrolled packet  was  sent
     
                    to a dead or non-effective host port.  However, if
     
                    it is resubmitted, there may be another  effective
     
                    host  port to which the IMP may be able to attempt
     
     
     
                                  - 40 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
                    to send the packet.
     
               7: Logical addressing is not in use in this network.
     
               8-15: Unassigned.
     
          Types 13-14,16-255: Unassigned.
     
     
     Bits 33-48: Source Host:
     
          For type 0 messages, this field contains the 1822L  name  or
     
          address  of  the  host  that  originated  the  message.  All
     
          replies to the message should be sent to the host  specified
     
          herein.   For  message types 5-9 and 15, this field contains
     
          the source host field used in a previous type 0 message sent
     
          by this host.
     
     
     Bits 49-64: Destination Host:
     
          For type 0 messages, this field contains the 1822L  name  or
     
          address  that  the  message  was  sent  to.  This allows the
     
          destination host to detect  how  it  was  specified  by  the
     
          source  host.   For  message  types  5-9  and 15, this field
     
          contains the destination host field used in a previous  type
     
          0 message sent by this host.
     
     
     Bits 65-76: Message ID:
     
          For message types 0, 5, 7-9,  and  15,  this  is  the  value
     
          assigned  by  the  source  host to identify the message (see
     
          section 3.1).  This field is also used by  message  types  2
     
     
     
     
                                  - 41 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
          and 6.
     
     
     Bits 77-80: Sub-type:
     
          This field is used as a modifier by message types 0-2,  5-7,
     
          9, and 15.
     
     
     Bits 81-96: Message Length:
     
          This field is contained in type 0, 3, 11,  and  12  messages
     
          only,  and  is  the  actual  length  in  bits of the message
     
          (exclusive of leader, leader padding, and hardware  padding)
     
          as computed by the IMP.
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
                                  - 42 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
     4  REFERENCES
     
     
     [1]  Specifications for the Interconnection of a Host and an IMP,
     
          BBN Report 1822, December 1981 Revision.
     
     
     [2]  A. Malis, The ARPANET Short Blocking  Feature,  Request  For
     
          Comments 852, April 1983.
     
     
     [3]  E. C. Rosen et. al., ARPANET Routing Algorithm Improvements,
     
          Internet  Experimenter's  Note  183  (also  published as BBN
     
          Report 4473, Vol. 1), August 1980, pp. 55-107.
     
     
     [4]  J. Postel,  Assigned  Numbers,  Request  For  Comments  820,
     
          January 1983, p. 11.
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
                                  - 43 -
     
     
     
     1822L Host Access Protocol                             April 1983
     RFC 851
     
     
     
                                   INDEX
     
     
     
     
     1822...................................................... 4
     1822 address.............................................. 6
     1822 host................................................. 5
     1822L..................................................... 4
     1822L address............................................. 7
     1822L host................................................ 5
     1822L name................................................ 6
     address selection policy................................. 12
     authorized................................................ 9
     blocking................................................. 22
     closest physical address................................. 13
     connection............................................... 22
     destination host..................................... 33, 41
     effective................................................ 10
     first reachable.......................................... 12
     handing type......................................... 29, 36
     host downs............................................... 13
     leader flags......................................... 29, 36
     link field............................................... 34
     load leveling............................................ 13
     logical addressing........................................ 4
     message ID........................................... 34, 41
     message length........................................... 42
     message type......................................... 30, 36
     multi-homing.............................................. 4
     name server...................................... 24, 32, 37
     NDM.................................................. 10, 30
     NDM reply............................................ 10, 37
     NOC....................................................... 9
     NOP........................................... 5, 20, 32, 37
     priority bit............................................. 29
     regular message...................................... 30, 36
     RFNM................................................. 22, 37
     source host.......................................... 33, 41
     standard message......................................... 30
     sub-type............................................. 34, 42
     symmetric................................................. 5
     trace bit............................................ 29, 36
     uncontrolled packet.................................. 18, 30
     
     
     
     
     
     
                                  - 44 -
     

Html markup produced by rfcmarkup 1.109, available from https://tools.ietf.org/tools/rfcmarkup/