[Docs] [txt|pdf|xml|html] [Tracker] [Email] [Diff1] [Diff2] [Nits]

Versions: (draft-thomson-http2-client-certs) 00 01 02 03 04

HTTP                                                           M. Bishop
Internet-Draft                                                 Microsoft
Intended status: Standards Track                              M. Thomson
Expires: May 4, 2017                                             Mozilla
                                                        October 31, 2016


             Secondary Certificate Authentication in HTTP/2
             draft-bishop-httpbis-http2-additional-certs-02

Abstract

   TLS provides fundamental mutual authentication services for HTTP,
   supporting up to one server certificate and up to one client
   certificate associated to the session to prove client and server
   identities as necessary.  This draft provides mechanisms for
   providing additional such certificates at the HTTP layer when these
   constraints are not sufficient.

   Many HTTP servers host content from several origins.  HTTP/2
   [RFC7540] permits clients to reuse an existing HTTP connection to a
   server provided that the secondary origin is also in the certificate
   provided during the TLS [I-D.ietf-tls-tls13] handshake.

   In many cases, servers will wish to maintain separate certificates
   for different origins but still desire the benefits of a shared HTTP
   connection.  Similarly, servers may require clients to present
   authentication, but have different requirements based on the content
   the client is attempting to access.

   This document describes a how TLS exported authenticators [I-D.draft-
   sullivan-tls-exported-authenticator] can be used to provide proof of
   ownership of additional certificates to the HTTP layer to support
   both scenarios.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any




Bishop & Thomson           Expires May 4, 2017                  [Page 1]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on May 4, 2017.

Copyright Notice

   Copyright (c) 2016 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
     1.1.  Server Certificate Authentication . . . . . . . . . . . .   3
     1.2.  Client Certificate Authentication . . . . . . . . . . . .   4
       1.2.1.  HTTP/1.1 using TLS 1.2 and previous . . . . . . . . .   4
       1.2.2.  HTTP/1.1 using TLS 1.3  . . . . . . . . . . . . . . .   5
       1.2.3.  HTTP/2  . . . . . . . . . . . . . . . . . . . . . . .   6
     1.3.  HTTP-Layer Certificate Authentication . . . . . . . . . .   6
     1.4.  Terminology . . . . . . . . . . . . . . . . . . . . . . .   7
   2.  Discovering Additional Certificates at the HTTP/2 Layer . . .   7
     2.1.  Indicating support for HTTP-layer certificate
           authentication  . . . . . . . . . . . . . . . . . . . . .   8
     2.2.  Making certificates or requests available . . . . . . . .   8
     2.3.  Requiring certificate authentication  . . . . . . . . . .   9
   3.  Certificates Frames for HTTP/2  . . . . . . . . . . . . . . .  10
     3.1.  The CERTIFICATE_NEEDED frame  . . . . . . . . . . . . . .  11
     3.2.  The USE_CERTIFICATE Frame . . . . . . . . . . . . . . . .  12
     3.3.  The CERTIFICATE_REQUEST Frame . . . . . . . . . . . . . .  13
     3.4.  The CERTIFICATE_PROOF Frame . . . . . . . . . . . . . . .  14
   4.  Indicating failures during HTTP-Layer Certificate
       Authentication  . . . . . . . . . . . . . . . . . . . . . . .  15
   5.  Security Considerations . . . . . . . . . . . . . . . . . . .  16
   6.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  17
     6.1.  HTTP/2 SETTINGS_HTTP_CERT_AUTH Setting  . . . . . . . . .  17
     6.2.  New HTTP/2 Frames . . . . . . . . . . . . . . . . . . . .  18
     6.3.  New HTTP/2 Error Codes  . . . . . . . . . . . . . . . . .  18
   7.  Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  18



Bishop & Thomson           Expires May 4, 2017                  [Page 2]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


   8.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  18
     8.1.  Normative References  . . . . . . . . . . . . . . . . . .  19
     8.2.  Informative References  . . . . . . . . . . . . . . . . .  20
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  20

1.  Introduction

   HTTP clients need to know that the content they receive on a
   connection comes from the origin that they intended to retrieve in
   from.  The traditional form of server authentication in HTTP has been
   in the form of X.509 certificates provided during the TLS RFC5246
   [I-D.ietf-tls-tls13] handshake.

   Many existing HTTP [RFC7230] servers also have authentication
   requirements for the resources they serve.  Of the bountiful
   authentication options available for authenticating HTTP requests,
   client certificates present a unique challenge for resource-specific
   authentication requirements because of the interaction with the
   underlying TLS layer.

   TLS 1.2 [RFC5246] supports one server and one client certificate on a
   connection.  These certificates may contain multiple identities, but
   only one certificate may be provided.

1.1.  Server Certificate Authentication

   Section 9.1.1 of [RFC7540] describes how connections may be used to
   make requests from multiple origins as long as the server is
   authoritative for both.  A server is considered authoritative for an
   origin if DNS resolves the origin to the IP address of the server and
   (for TLS) if the certificate presented by the server contains the
   origin in the Subject Alternative Names field.

   [I-D.ietf-httpbis-alt-svc] enables a step of abstraction from the DNS
   resolution.  If both hosts have provided an Alternative Service at
   hostnames which resolve to the IP address of the server, they are
   considered authoritative just as if DNS resolved the origin itself to
   that address.  However, the server's one TLS certificate is still
   required to contain the name of each origin in question.

   Servers which host many origins often would prefer to have separate
   certificates for some sets of origins.  This may be for ease of
   certificate management (the ability to separately revoke or renew
   them), due to different sources of certificates (a CDN acting on
   behalf of multiple origins), or other factors which might drive this
   administrative decision.  Clients connecting to such origins cannot
   currently reuse connections, even if both client and server would
   prefer to do so.



Bishop & Thomson           Expires May 4, 2017                  [Page 3]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


   Because the TLS SNI extension is exchanged in the clear, clients
   might also prefer to retrieve certificates inside the encrypted
   context.  When this information is sensitive, it might be
   advantageous to request a general-purpose certificate or anonymous
   ciphersuite at the TLS layer, while acquiring the "real" certificate
   in HTTP after the connection is established.

1.2.  Client Certificate Authentication

   For servers that wish to use client certificates to authenticate
   users, they might request client authentication during or immediately
   after the TLS handshake.  However, if not all users or resources need
   certificate-based authentication, a request for a certificate has the
   unfortunate consequence of triggering the client to seek a
   certificate, possibly requiring user interaction, network traffic, or
   other time-consuming activities.  During this time, the connection is
   stalled in many implementations.  Such a request can result in a poor
   experience, particularly when sent to a client that does not expect
   the request.

   The TLS 1.3 CertificateRequest can be used by servers to give clients
   hints about which certificate to offer.  Servers that rely on
   certificate-based authentication might request different certificates
   for different resources.  Such a server cannot use contextual
   information about the resource to construct an appropriate TLS
   CertificateRequest message during the initial handshake.

   Consequently, client certificates are requested at connection
   establishment time only in cases where all clients are expected or
   required to have a single certificate that is used for all resources.
   Many other uses for client certificates are reactive, that is,
   certificates are requested in response to the client making a
   request.

1.2.1.  HTTP/1.1 using TLS 1.2 and previous

   In HTTP/1.1, a server that relies on client authentication for a
   subset of users or resources does not request a certificate when the
   connection is established.  Instead, it only requests a client
   certificate when a request is made to a resource that requires a
   certificate.  TLS 1.2 [RFC5246] accomodates this by permitting the
   server to request a new TLS handshake, in which the server will
   request the client's certificate.

   Figure 1 shows the server initiating a TLS-layer renegotiation in
   response to receiving an HTTP/1.1 request to a protected resource.





Bishop & Thomson           Expires May 4, 2017                  [Page 4]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


   Client                                      Server
      -- (HTTP) GET /protected -------------------> *1
      <---------------------- (TLS) HelloRequest -- *2
      -- (TLS) ClientHello ----------------------->
      <------------------ (TLS) ServerHello, ... --
      <---------------- (TLS) CertificateRequest -- *3
      -- (TLS) ..., Certificate ------------------> *4
      -- (TLS) Finished -------------------------->
      <-------------------------- (TLS) Finished --
      <--------------------------- (HTTP) 200 OK -- *5

    Figure 1: HTTP/1.1 Reactive Certificate Authentication with TLS 1.2

   In this example, the server receives a request for a protected
   resource (at *1 on Figure 1).  Upon performing an authorization
   check, the server determines that the request requires authentication
   using a client certificate and that no such certificate has been
   provided.

   The server initiates TLS renegotiation by sending a TLS HelloRequest
   (at *2).  The client then initiates a TLS handshake.  Note that some
   TLS messages are elided from the figure for the sake of brevity.

   The critical messages for this example are the server requesting a
   certificate with a TLS CertificateRequest (*3); this request might
   use information about the request or resource.  The client then
   provides a certificate and proof of possession of the private key in
   Certificate and CertificateVerify messages (*4).

   When the handshake completes, the server performs any authorization
   checks a second time.  With the client certificate available, it then
   authorizes the request and provides a response (*5).

1.2.2.  HTTP/1.1 using TLS 1.3

   TLS 1.3 [I-D.ietf-tls-tls13] introduces a new client authentication
   mechanism that allows for clients to authenticate after the handshake
   has been completed.  For the purposes of authenticating an HTTP
   request, this is functionally equivalent to renegotiation.  Figure 2
   shows the simpler exchange this enables.

   Client                                      Server
      -- (HTTP) GET /protected ------------------->
      <---------------- (TLS) CertificateRequest --
      -- (TLS) Certificate, CertificateVerify ---->
      <--------------------------- (HTTP) 200 OK --

    Figure 2: HTTP/1.1 Reactive Certificate Authentication with TLS 1.3



Bishop & Thomson           Expires May 4, 2017                  [Page 5]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


   TLS 1.3 does not support renegotiation, instead supporting direct
   client authentication.  In contrast to the TLS 1.2 example, in TLS
   1.3, a server can simply request a certificate.

1.2.3.  HTTP/2

   An important part of the HTTP/1.1 exchange is that the client is able
   to easily identify the request that caused the TLS renegotiation.
   The client is able to assume that the next unanswered request on the
   connection is responsible.  The HTTP stack in the client is then able
   to direct the certificate request to the application or component
   that initiated that request.  This ensures that the application has
   the right contextual information for processing the request.

   In HTTP/2, a client can have multiple outstanding requests.  Without
   some sort of correlation information, a client is unable to identify
   which request caused the server to request a certificate.

   Thus, the minimum necessary mechanism to support reactive certificate
   authentication in HTTP/2 is an identifier that can be use to
   correlate an HTTP request with a request for a certificate.  Since
   streams are used for individual requests, correlation with a stream
   is sufficient.

   [RFC7540] prohibits renegotiation after any application data has been
   sent.  This completely blocks reactive certificate authentication in
   HTTP/2 using TLS 1.2.  If this restriction were relaxed by an
   extension or update to HTTP/2, such an identifier could be added to
   TLS 1.2 by means of an extension to TLS.  Unfortunately, many TLS 1.2
   implementations do not permit application data to continue during a
   renegotiation.  This is problematic for a multiplexed protocol like
   HTTP/2.

1.3.  HTTP-Layer Certificate Authentication

   This draft proposes bringing a request/response mechanism that is
   equivalent to the the TLS 1.3 CertificateRequest, Certificate,
   CertificateVerify and Finished messages into HTTP/2 frames, enabling
   certificate-based authentication of both clients and servers
   independent of TLS version.  This mechanism can be implemented at the
   HTTP layer without breaking the existing interface between HTTP and
   applications above it.

   This could be done in a naive manner by replicating the messages as
   HTTP/2 frames on each stream.  However, this would create needless
   redundancy between streams and require frequent expensive signing
   operations.  Instead, this draft lifts the bulky portions of each




Bishop & Thomson           Expires May 4, 2017                  [Page 6]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


   message into frames on stream zero and permits the on-stream frames
   to incorporate them by reference as needed.

   Certificate chains, with proof-of-possession of the corresponding
   private key, can be supplied into a collection of available
   certificates.  Likewise, descriptions of desired certificates can be
   supplied into these collections.  These pre-supplied elements are
   then available for automatic use (in some situations) or for
   reference by individual streams.

   Section 2 describes how the feature is employed, defining means to
   detect support in peers (Section 2.1), make certificates and requests
   available (Section 2.2), and indicate when streams are blocked
   waiting on an appropriate certificate (Section 2.3).  Section 3
   defines the required frame types, which parallel the TLS 1.3 message
   exchange.  Finally, Section 4 defines new error types which can be
   used to notify peers when the exchange has not been successful.

1.4.  Terminology

   RFC 2119 [RFC2119] defines the terms "MUST", "MUST NOT", "SHOULD" and
   "MAY".

2.  Discovering Additional Certificates at the HTTP/2 Layer

   A certificate chain with proof of possesion of the private key
   corresponding to the end-entity certificate is sent as a single of
   "CERTIFICATE_PROOF" frame (see Section 3.4) on stream zero.  Once the
   holder of a certificate has sent the chain and proof, this
   certificate chain is cached by the recipient and available for future
   use.  If the certificate is marked as "AUTOMATIC_USE", the
   certificate may be used by the recipient to authorize any current or
   future request.  Otherwise, the recipient requests the required
   certificate on each stream, but the previously-supplied certificates
   are available for reference without having to resend them.

   Likewise, the details of a request are sent on stream zero and stored
   by the recipient.  These details will be referenced by subsequent
   "CERTIFICATE_NEEDED" frames.

   Data sent by each peer is correlated by the ID given in each frame.
   This ID is unrelated to values used by the other peer, even if each
   uses the same ID in certain cases.








Bishop & Thomson           Expires May 4, 2017                  [Page 7]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


2.1.  Indicating support for HTTP-layer certificate authentication

   Clients and servers that will accept requests for HTTP-layer
   certificate authentication indicate this using the HTTP/2
   "SETTINGS_HTTP_CERT_AUTH" (0xSETTING-TBD) setting.

   The initial value for the "SETTINGS_HTTP_CERT_AUTH" setting is 0,
   indicating that the peer does not support HTTP-layer certificate
   authentication.  If a peer does support HTTP-layer certificate
   authentication, the value is 1.

2.2.  Making certificates or requests available

   When a peer has advertised support for HTTP-layer certificates as in
   Section 2.1, either party can supply additional certificates into the
   connection at any time.  These certificates then become available for
   the peer to consider when deciding whether a connection is suitable
   to transport a particular request.

   Available certificates which have the "AUTOMATIC_USE" flag set MAY be
   used by the recipient without further notice.  This means that
   clients or servers which predict a certificate will be required could
   pre-supply the certificate without being asked.  Regardless of
   whether "AUTOMATIC_USE" is set, these certificates are available for
   reference by future "USE_CERTIFICATE" frames.

   Client                                      Server
      <-- (stream 0) CERTIFICATE_PROOF (AU flag) --
      ...
      -- (stream N) GET /from-new-origin --------->
      <----------------------- (stream N) 200 OK --


                  Figure 3: Proactive Server Certificate

   Client                                      Server
      -- (stream 0) CERTIFICATE_PROOF (AU flag) -->
      -- (streams 1,3) GET /protected ------------>
      <-------------------- (streams 1,3) 200 OK --


                  Figure 4: Proactive Client Certificate

   Likewise, either party can supply a "CERTIFICATE_REQUEST" that
   outlines parameters of a certificate they might request in the
   future.  It is important to note that this does not currently request
   such a certificate, but makes the contents of the request available
   for reference by a future "CERTIFICATE_NEEDED" frame.



Bishop & Thomson           Expires May 4, 2017                  [Page 8]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


   Because certificates can be large and each "CERTIFICATE_PROOF"
   requires a signing operation, the server MAY instead send an "ORIGIN"
   frame including origins which are not in its TLS certificate.  This
   represents an explicit claim by the server to possess the appropriate
   certificate - a claim the client MUST verify using the procedures in
   Section 2.3 before relying on the server's authority for the claimed
   origin.

2.3.  Requiring certificate authentication

   As defined in [RFC7540], when a client finds that a https:// origin
   (or Alternative Service [I-D.ietf-httpbis-alt-svc]) to which it needs
   to make a request has the same IP address as a server to which it is
   already connected, it MAY check whether the TLS certificate provided
   contains the new origin as well, and if so, reuse the connection.

   If the TLS certificate does not contain the new origin, but the
   server has advertised support for HTTP-layer certificates (see
   Section 2.1), it MAY send a "CERTIFICATE_NEEDED" frame on the stream
   it will use to make the request.  (If the request parameters have not
   already been made available using a "CERTIFICATE_REQUEST" frame, the
   client will need to send the "CERTIFICATE_REQUEST" in order to
   generate the "CERTIFICATE_NEEDED" frame.)  The stream represents a
   pending request to that origin which is blocked until a valid
   certificate is processed.

   The request is blocked until the server has responded with a
   "USE_CERTIFICATE" frame pointing to a certificate for that origin.
   If the certificate is already available, the server SHOULD
   immediately respond with the appropriate "USE_CERTIFICATE" frame.
   (If the certificate has not already been transmitted, the server will
   need to make the certificate available as described in Section 2.2
   before completing the exchange.)

   If the server does not have the desired certificate or cannot produce
   a signature compatible with the client's advertised settings, it MUST
   respond with an empty "USE_CERTIFICATE" frame.  In this case, or if
   the server has not advertised support for HTTP-layer certificates,
   the client MUST NOT send any requests for resources in that origin on
   the current connection.











Bishop & Thomson           Expires May 4, 2017                  [Page 9]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


   Client                                      Server
      <----------------------- (stream 0) ORIGIN --
      -- (stream 0) CERTIFICATE_REQUEST ---------->
      ...
      -- (stream N) CERTIFICATE_NEEDED --------->
      <------------ (stream 0) CERTIFICATE_PROOF --
      <-------------- (stream N) USE_CERTIFICATE --
      -- (stream N) GET /from-new-origin --------->
      <----------------------- (stream N) 200 OK --


                  Figure 5: Client-Requested Certificate

   Likewise, on each stream where certificate authentication is
   required, the server sends a "CERTIFICATE_NEEDED" frame, which the
   client answers with a "USE_CERTIFICATE" frame indicating the
   certificate to use.  If the request parameters or the responding
   certificate are not already available, they will need to be sent as
   described in Section 2.2 as part of this exchange.

   Client                                      Server
      <---------- (stream 0) CERTIFICATE_REQUEST --
      ...
      -- (stream N) GET /protected --------------->
      <--------- (stream N) CERTIFICATE_NEEDED --
      -- (stream 0) CERTIFICATE_PROOF ------------>
      -- (stream N) USE_CERTIFICATE -------------->
      <----------------------- (stream N) 200 OK --


               Figure 6: Reactive Certificate Authentication

   A server SHOULD provide certificates for an origin before pushing
   resources from it.  If a client receives a "PUSH_PROMISE" referencing
   an origin for which it has not yet received the server's certificate,
   the client MUST verify the server's possession of an appropriate
   certificate by sending a "CERTIFICATE_NEEDED" frame on the pushed
   stream to inform the server that progress is blocked until the
   request is satisfied.  The client MUST NOT use the pushed resource
   until an appropriate certificate has been received and validated.

3.  Certificates Frames for HTTP/2

   The "CERTIFICATE_REQUEST" and "CERTIFICATE_NEEDED" frames are
   correlated by their "Request-ID" field.  Subsequent
   "CERTIFICATE_NEEDED" frames with the same "Request-ID" value MAY be
   sent on other streams where the sender is expecting a certificate
   with the same parameters.



Bishop & Thomson           Expires May 4, 2017                 [Page 10]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


   The "CERTIFICATE_PROOF", and "USE_CERTIFICATE" frames are correlated
   by their "Cert-ID" field.  Subsequent "USE_CERTIFICATE" frames with
   the same "Cert-ID" MAY be sent in response to other
   "CERTIFICATE_NEEDED" frames and refer to the same certificate.

   "Request-ID" and "Cert-ID" are sender-local, and the use of the same
   value by the other peer does not imply any correlation between their
   frames.

3.1.  The CERTIFICATE_NEEDED frame

   The "CERTIFICATE_NEEDED" frame (0xFRAME-TBD2) is sent to indicate
   that the HTTP request on the current stream is blocked pending
   certificate authentication.  The frame includes a request identifier
   which can be used to correlate the stream with a previous
   "CERTIFICATE_REQUEST" frame sent on stream zero.  The
   "CERTIFICATE_REQUEST" describes the certificate the sender requires
   to make progress on the stream in question.

   The "CERTIFICATE_NEEDED" frame contains 1 octet, which is the
   authentication request identifier, "Request-ID".  A peer that
   receives a "CERTIFICATE_NEEDED" of any other length MUST treat this
   as a stream error of type "PROTOCOL_ERROR".  Frames with identical
   request identifiers refer to the same "CERTIFICATE_REQUEST".

   A server MAY send multiple "CERTIFICATE_NEEDED" frames on the same
   stream.  If a server requires that a client provide multiple
   certificates before authorizing a single request, each required
   certificate MUST be indicated with a separate "CERTIFICATE_NEEDED"
   frame, each of which MUST have a different request identifier
   (referencing different "CERTIFICATE_REQUEST" frames describing each
   required certificate).  To reduce the risk of client confusion,
   servers SHOULD NOT have multiple outstanding "CERTIFICATE_NEEDED"
   frames on the same stream at any given time.

   Clients MUST NOT send multiple "CERTIFICATE_NEEDED" frames on the
   same stream.

   The "CERTIFICATE_NEEDED" frame MUST NOT be sent to a peer which has
   not advertised support for HTTP-layer certificate authentication.

   The "CERTIFICATE_NEEDED" frame MUST NOT be sent on stream zero, and
   MUST NOT be sent on a stream in the "half-closed (local)" state
   [RFC7540].  A client that receives a "CERTIFICATE_NEEDED" frame on a
   stream which is not in a valid state SHOULD treat this as a stream
   error of type "PROTOCOL_ERROR".





Bishop & Thomson           Expires May 4, 2017                 [Page 11]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


3.2.  The USE_CERTIFICATE Frame

   The "USE_CERTIFICATE" frame (0xFRAME-TBD5) is sent in response to a
   "CERTIFICATE_NEEDED" frame to indicate which certificate is being
   used to satisfy the requirement.

   A "USE_CERTIFICATE" frame with no payload refers to the certificate
   provided at the TLS layer, if any.  If no certificate was provided at
   the TLS layer, the stream should be processed with no authentication,
   likely returning an authentication-related error at the HTTP level
   (e.g. 403) for servers or routing the request to a new connection for
   clients.

   Otherwise, the "USE_CERTIFICATE" frame contains the "Cert-ID" of the
   certificate the sender wishes to use.  This MUST be the ID of a
   certificate for which proof of possession has been presented in a
   "CERTIFICATE_PROOF" frame.  Recipients of a "USE_CERTIFICATE" frame
   of any other length MUST treat this as a stream error of type
   "PROTOCOL_ERROR".  Frames with identical certificate identifiers
   refer to the same certificate chain.

   The "USE_CERTIFICATE" frame MUST NOT be sent on stream zero or a
   stream on which a "CERTIFICATE_NEEDED" frame has not been received.
   Receipt of a "USE_CERTIFICATE" frame in these circmustances SHOULD be
   treated as a stream error of type "PROTOCOL_ERROR".  Each
   "USE_CERTIFICATE" frame should reference a preceding
   "CERTIFICATE_PROOF" frame.  Receipt of a "USE_CERTIFICATE" frame
   before the necessary frames have been received on stream zero MUST
   also result in a stream error of type "PROTOCOL_ERROR".

   The referenced certificate chain MUST conform to the requirements
   expressed in the "CERTIFICATE_REQUEST" to the best of the sender's
   ability.  Specifically:

   o  If the "CERTIFICATE_REQUEST" contained a non-empty "Certificate-
      Authorities" element, one of the certificates in the chain SHOULD
      be signed by one of the listed CAs.

   o  If the "CERTIFICATE_REQUEST" contained a non-empty "Cert-
      Extensions" element, the first certificate MUST match with regard
      to the extension OIDs recognized by the sender.

   If these requirements are not satisfied, the recipient MAY at its
   discretion either return an error at the HTTP semantic layer, or
   respond with a stream error [RFC7540] on any stream where the
   certificate is used.  Section 4 defines certificate-related error
   codes which might be applicable.




Bishop & Thomson           Expires May 4, 2017                 [Page 12]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


3.3.  The CERTIFICATE_REQUEST Frame

   TLS 1.3 defines the "CertificateRequest" message, which prompts the
   client to provide a certificate which conforms to certain properties
   specified by the server.  This draft defines the
   "CERTIFICATE_REQUEST" frame (0xFRAME-TBD1), which contains the same
   contents as a TLS 1.3 "CertificateRequest" message, but can be sent
   over any TLS version.

   The "CERTIFICATE_REQUEST" frame SHOULD NOT be sent to a peer which
   has not advertised support for HTTP-layer certificate authentication.

   The "CERTIFICATE_REQUEST" frame MUST be sent on stream zero.  A
   "CERTIFICATE_REQUEST" frame received on any other stream MUST be
   rejected with a stream error of type "PROTOCOL_ERROR".

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-------------------------------+---------------+---------------+
    | Request-ID (8)|        CA-Count (16)          |
    +-----------------------------------------------+---------------+
    |                   Certificate-Authorities (?)               ...
    +---------------------------------------------------------------+
    |   Cert-Extension-Count (16)   |       Cert-Extensions(?)    ...
    +---------------------------------------------------------------+

                Figure 7: CERTIFICATE_REQUEST frame payload

   The frame contains the following fields:

   Request-ID:  "Request-ID" is an 8-bit opaque identifier used to
      correlate subsequent certificate-related frames with this request.
      The identifier MUST be unique in the session for the sender.

   CA-Count and Certificate-Authorities:  "Certificate-Authorities" is a
      series of distinguished names of acceptable certificate
      authorities, represented in DER-encoded [X690] format.  These
      distinguished names may specify a desired distinguished name for a
      root CA or for a subordinate CA; thus, this message can be used to
      describe known roots as well as a desired authorization space.
      The number of such structures is given by the 16-bit "CA-Count"
      field, which MAY be zero.  If the "CA-Count" field is zero, then
      the recipient MAY send any certificate that meets the rest of the
      selection criteria in the "CERTIFICATE_REQUEST", unless there is
      some external arrangement to the contrary.

   Cert-Extension-Count and Cert-Extensions:  A list of certificate
      extension OIDs [RFC5280] with their allowed values, represented in



Bishop & Thomson           Expires May 4, 2017                 [Page 13]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


      a series of "CertificateExtension" structures (see
      [I-D.ietf-tls-tls13] section 6.3.5).  The list of OIDs MUST be
      used in certificate selection as described in
      [I-D.ietf-tls-tls13].  The number of Cert-Extension structures is
      given by the 16-bit "Cert-Extension-Count" field, which MAY be
      zero.

   Some certificate extension OIDs allow multiple values (e.g.  Extended
   Key Usage).  If the sender has included a non-empty Cert-Extensions
   list, the certificate MUST contain all of the specified extension
   OIDs that the recipient recognizes.  For each extension OID
   recognized by the recipient, all of the specified values MUST be
   present in the certificate (but the certificate MAY have other values
   as well).  However, the recipient MUST ignore and skip any
   unrecognized certificate extension OIDs.

   Servers MUST be able to recognize the "subjectAltName" extension
   ([RFC2459] section 4.2.1.7) at a minimum.  Clients MUST always
   specify the desired origin using this extension, though other
   extensions MAY also be included.

   PKIX RFCs define a variety of certificate extension OIDs and their
   corresponding value types.  Depending on the type, matching
   certificate extension values are not necessarily bitwise-equal.  It
   is expected that implementations will rely on their PKI libraries to
   perform certificate selection using these certificate extension OIDs.

3.4.  The CERTIFICATE_PROOF Frame

   The "CERTIFICATE_PROOF" frame provides a exported authenticator
   message from the TLS layer that provides a chain of certificates,
   associated extensions and proves possession of the private key
   corresponding to the end-entity certificate.

   The "CERTIFICATE_PROOF" frame defines one flag:

   AUTOMATIC_USE (0x01):  Indicates that the certificate can be used
      automatically on future requests.

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-------------------------------+-------------------------------+
    |  Cert-ID (8)  |         Exported Authenticator(*)...
    +---------------------------------------------------------------+


                 Figure 8: CERTIFICATE_PROOF frame payload




Bishop & Thomson           Expires May 4, 2017                 [Page 14]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


   The "CERTIFICATE_PROOF" frame (0xFRAME-TBD4) contains an "Exported
   Authenticator" field which corresponds to the value returned from the
   TLS connection exported authenticator API when provided with a
   certificate, a valid certificate chain for the connection and
   associated extensions (OCSP, SCT, etc.), and a connection-unique
   8-byte certificate_request_context value.

   If the "AUTOMATIC_USE" flag is set, the recipient MAY omit sending
   "CERTIFICATE_NEEDED" frames on future streams which would require a
   similar certificate and use the referenced certificate for
   authentication without further notice to the holder.  This behavior
   is optional, and receipt of a "CERTIFICATE_NEEDED" frame does not
   imply that previously-presented certificates were unacceptable, even
   if "AUTOMATIC_USE" was set.  Servers MUST set the "AUTOMATIC_USE"
   flag when sending a "CERTIFICATE_PROOF" frame.  A server MUST NOT
   send certificates for origins which it is not prepared to service on
   the current connection.

   Upon recieving a CERTIFICATE_PROOF frame, the reciever may validate
   the Exported Authenticator value by using the exported authenticator
   API.  This return either an error indicating that the message was
   invalid, or the certificate chain and extensions used to create the
   message.

4.  Indicating failures during HTTP-Layer Certificate Authentication

   Because this draft permits certificates to be exchanged at the HTTP
   framing layer instead of the TLS layer, several certificate-related
   errors which are defined at the TLS layer might now occur at the HTTP
   framing layer.  In this section, those errors are restated and added
   to the HTTP/2 error code registry.

   BAD_CERTIFICATE (0xERROR-TBD1):  A certificate was corrupt, contained
      signatures that did not verify correctly, etc.

   UNSUPPORTED_CERTIFICATE (0xERROR-TBD2):  A certificate was of an
      unsupported type or did not contain required extensions

   CERTIFICATE_REVOKED (0xERROR-TBD3):  A certificate was revoked by its
      signer

   CERTIFICATE_EXPIRED (0xERROR-TBD4):  A certificate has expired or is
      not currently valid

   CERTIFICATE_TOO_LARGE (0xERROR-TBD5):  The certificate cannot be
      transferred due to the recipient's "SETTINGS_MAX_FRAME_SIZE"





Bishop & Thomson           Expires May 4, 2017                 [Page 15]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


   CERTIFICATE_GENERAL (0xERROR-TBD6):  Any other certificate-related
      error

   As described in [RFC7540], implementations MAY choose to treat a
   stream error as a connection error at any time.  Of particular note,
   a stream error cannot occur on stream 0, which means that
   implementations cannot send non-session errors in response to
   "CERTIFICATE_REQUEST", and "CERTIFICATE_PROOF" frames.
   Implementations which do not wish to terminate the connection MAY
   either send relevant errors on any stream which references the
   failing certificate in question or process the requests as
   unauthenticated and provide error information at the HTTP semantic
   layer.

5.  Security Considerations

   This mechanism defines an alternate way to obtain server and client
   certificates other than in the initial TLS handshake.  While the
   signature of exported authenticator values is expected to be equally
   secure, it is important to recognize that a vulnerability in this
   code path is at least equal to a vulnerability in the TLS handshake.

   This could also increase the impact of a key compromise.  Rather than
   needing to subvert DNS or IP routing in order to use a compromised
   certificate, a malicious server now only needs a client to connect to
   _some_ HTTPS site under its control.  Clients SHOULD continue to
   validate that destination IP addresses are valid for the origin
   either by direct DNS resolution or resolution of a validated
   Alternative Service.  (Future work could include a mechanism for a
   server to offer proofs.)

   This draft defines a mechanism which could be used to probe servers
   for origins they support, but opens no new attack versus making
   repeat TLS connections with different SNI values.  Servers SHOULD
   impose similar denial-of-service mitigations (e.g. request rate
   limits) to "CERTIFICATE_REQUEST" frames as to new TLS connections.

   While the "CERTIFICATE_REQUEST" frame permits the sender to enumerate
   the acceptable Certificate Authorities for the requested certificate,
   it might not be prudent (either for security or data consumption) to
   include the full list of trusted Certificate Authorities in every
   request.  Senders, particularly clients, are advised to send an empty
   "Certificate-Authorities" element unless they are expecting a
   certificate to be signed by a particular CA or small set of CAs.

   Failure to provide a certificate on a stream after receiving
   "CERTIFICATE_NEEDED" blocks processing, and SHOULD be subject to
   standard timeouts used to guard against unresponsive peers.



Bishop & Thomson           Expires May 4, 2017                 [Page 16]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


   Client implementations need to carefully consider the impact of
   setting the "AUTOMATIC_USE" flag.  This flag is a performance
   optimization, permitting the client to avoid a round-trip on each
   request where the server checks for certificate authentication.
   However, once this flag has been sent, the client has zero knowledge
   about whether the server will use the referenced cert for any future
   request, or even for an existing request which has not yet completed.
   Clients MUST NOT set this flag on any certificate which is not
   appropriate for currently-in-flight requests, and MUST NOT make any
   future requests on the same connection which they are not willing to
   have associated with the provided certificate.

   Implementations need to be aware of the potential for confusion about
   the state of a connection.  The presence or absence of a validated
   certificate can change during the processing of a request,
   potentially multiple times, as "USE_CERTIFICATE" frames are received.
   A server that uses certificate authentication needs to be prepared to
   reevaluate the authorization state of a request as the set of
   certificates changes.

   Finally, validating a multitude of signatures can be computationally
   expensive, while generating an invalid signature is computationally
   cheap.  Implementations will require checks against attacks from this
   direction.  Signature proofs SHOULD NOT be validated until a stream
   requires the certificate to make progress.  A signature which is not
   valid based on the asserted public key SHOULD be treated as a session
   error, to avoid further attacks from the peer, though an
   implementation MAY instead disable HTTP-layer certificates for the
   current connection instead.

6.  IANA Considerations

   This draft adds entries in three registries.

   The HTTP/2 "SETTINGS_HTTP_CERT_AUTH" setting is registered in
   Section 6.1.  Five frame types are registered in Section 6.2.  Six
   error codes are registered in Section 6.3.

6.1.  HTTP/2 SETTINGS_HTTP_CERT_AUTH Setting

   The SETTINGS_HTTP_CERT_AUTH setting is registered in the "HTTP/2
   Settings" registry established in [RFC7540].

   Name:  SETTINGS_HTTP_CERT_AUTH

   Code:  0xSETTING-TBD

   Initial Value:  0



Bishop & Thomson           Expires May 4, 2017                 [Page 17]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


   Specification:  This document.

6.2.  New HTTP/2 Frames

   Four new frame types are registered in the "HTTP/2 Frame Types"
   registry established in [RFC7540].  The entries in the following
   table are registered by this document.

   +---------------------+--------------+-------------------------+
   | Frame Type          | Code         | Specification           |
   +---------------------+--------------+-------------------------+
   | CERTIFICATE_NEEDED  | 0xFRAME-TBD1 | {{http-cert-needed}}    |
   | CERTIFICATE_REQUEST | 0xFRAME-TBD2 | {{http-cert-request}}   |
   | CERTIFICATE_PROOF   | 0xFRAME-TBD3 | {{http-cert-proof}}     |
   | USE_CERTIFICATE     | 0xFRAME-TBD4 | {{http-use-certificate}}|
   +---------------------+--------------+-------------------------+

                                 Figure 9

6.3.  New HTTP/2 Error Codes

   Five new error codes are registered in the "HTTP/2 Error Code"
   registry established in [RFC7540].  The entries in the following
   table are registered by this document.

   +-------------------------+--------------+-------------------------+
   | Name                    | Code         | Specification           |
   +-------------------------+--------------+-------------------------+
   | BAD_CERTIFICATE         | 0xERROR-TBD1 | {{errors}}              |
   | UNSUPPORTED_CERTIFICATE | 0xERROR-TBD2 | {{errors}}              |
   | CERTIFICATE_REVOKED     | 0xERROR-TBD3 | {{errors}}              |
   | CERTIFICATE_EXPIRED     | 0xERROR-TBD4 | {{errors}}              |
   | CERTIFICATE_GENERAL     | 0xERROR-TBD5 | {{errors}}              |
   +-------------------------+--------------+-------------------------+

                                 Figure 10

7.  Acknowledgements

   Eric Rescorla pointed out several failings in an earlier revision.
   Andrei Popov contributed to the TLS considerations.

8.  References








Bishop & Thomson           Expires May 4, 2017                 [Page 18]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


8.1.  Normative References

   [I-D.ietf-tls-tls13]
              Rescorla, E., "The Transport Layer Security (TLS) Protocol
              Version 1.3", draft-ietf-tls-tls13-18 (work in progress),
              October 2016.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <http://www.rfc-editor.org/info/rfc2119>.

   [RFC2459]  Housley, R., Ford, W., Polk, W., and D. Solo, "Internet
              X.509 Public Key Infrastructure Certificate and CRL
              Profile", RFC 2459, DOI 10.17487/RFC2459, January 1999,
              <http://www.rfc-editor.org/info/rfc2459>.

   [RFC5246]  Dierks, T. and E. Rescorla, "The Transport Layer Security
              (TLS) Protocol Version 1.2", RFC 5246,
              DOI 10.17487/RFC5246, August 2008,
              <http://www.rfc-editor.org/info/rfc5246>.

   [RFC5280]  Cooper, D., Santesson, S., Farrell, S., Boeyen, S.,
              Housley, R., and W. Polk, "Internet X.509 Public Key
              Infrastructure Certificate and Certificate Revocation List
              (CRL) Profile", RFC 5280, DOI 10.17487/RFC5280, May 2008,
              <http://www.rfc-editor.org/info/rfc5280>.

   [RFC5705]  Rescorla, E., "Keying Material Exporters for Transport
              Layer Security (TLS)", RFC 5705, DOI 10.17487/RFC5705,
              March 2010, <http://www.rfc-editor.org/info/rfc5705>.

   [RFC7230]  Fielding, R., Ed. and J. Reschke, Ed., "Hypertext Transfer
              Protocol (HTTP/1.1): Message Syntax and Routing",
              RFC 7230, DOI 10.17487/RFC7230, June 2014,
              <http://www.rfc-editor.org/info/rfc7230>.

   [RFC7540]  Belshe, M., Peon, R., and M. Thomson, Ed., "Hypertext
              Transfer Protocol Version 2 (HTTP/2)", RFC 7540,
              DOI 10.17487/RFC7540, May 2015,
              <http://www.rfc-editor.org/info/rfc7540>.

   [RFC7627]  Bhargavan, K., Ed., Delignat-Lavaud, A., Pironti, A.,
              Langley, A., and M. Ray, "Transport Layer Security (TLS)
              Session Hash and Extended Master Secret Extension",
              RFC 7627, DOI 10.17487/RFC7627, September 2015,
              <http://www.rfc-editor.org/info/rfc7627>.




Bishop & Thomson           Expires May 4, 2017                 [Page 19]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


   [X690]     ITU-T, "Information technology - ASN.1 encoding Rules:
              Specification of Basic Encoding Rules (BER), Canonical
              Encoding Rules (CER) and Distinguished Encoding Rules
              (DER)", ISO ISO/IEC 8825-1:2002, 2002,
              <http://www.itu.int/ITU-T/studygroups/com17/languages/
              X.690-0207.pdf>.

8.2.  Informative References

   [FIPS-186-4]
              National Institute of Standards and Technology, "Digital
              Signature Standard (DSS)", FIPS 186-4, July 2013,
              <http://nvlpubs.nist.gov/nistpubs/FIPS/
              NIST.FIPS.186-4.pdf>.

   [I-D.ietf-httpbis-alt-svc]
              Nottingham, M., McManus, P., and J. Reschke, "HTTP
              Alternative Services", draft-ietf-httpbis-alt-svc-14 (work
              in progress), March 2016.

   [I-D.josefsson-eddsa-ed25519]
              Josefsson, S. and N. Moller, "EdDSA and Ed25519", draft-
              josefsson-eddsa-ed25519-03 (work in progress), May 2015.

   [I-D.nottingham-httpbis-origin-frame]
              Nottingham, M. and E. Nygren, "The ORIGIN HTTP/2 Frame",
              draft-nottingham-httpbis-origin-frame-01 (work in
              progress), January 2016.

   [PKCS.1.1991]
              RSA Laboratories, "RSA Encryption Standard, Version 1.1",
              PKCS 1, June 1991.

   [RFC2560]  Myers, M., Ankney, R., Malpani, A., Galperin, S., and C.
              Adams, "X.509 Internet Public Key Infrastructure Online
              Certificate Status Protocol - OCSP", RFC 2560,
              DOI 10.17487/RFC2560, June 1999,
              <http://www.rfc-editor.org/info/rfc2560>.

   [RFC6962]  Laurie, B., Langley, A., and E. Kasper, "Certificate
              Transparency", RFC 6962, DOI 10.17487/RFC6962, June 2013,
              <http://www.rfc-editor.org/info/rfc6962>.

Authors' Addresses







Bishop & Thomson           Expires May 4, 2017                 [Page 20]


Internet-Draft        Secondary Cert Auth in HTTP/2         October 2016


   Mike Bishop
   Microsoft

   Email: michael.bishop@microsoft.com


   Martin Thomson
   Mozilla

   Email: martin.thomson@gmail.com









































Bishop & Thomson           Expires May 4, 2017                 [Page 21]


Html markup produced by rfcmarkup 1.123, available from https://tools.ietf.org/tools/rfcmarkup/