[Docs] [txt|pdf] [Tracker] [WG] [Email] [Nits]

Versions: 00 01 02 03 04 05 draft-ietf-softwire-map-mib

Network Working Group                                            Y. Fu
Internet Draft                                                S. Jiang
Intended status: Standards Track          Huawei Technologies Co., Ltd
Expires: September 4, 2012                                      J.Dong
                                                                 P. Wu
                                                   Tsinghua University
                                                         March 1, 2012

                Definitions of Managed Objects for MAP-E
                      draft-fu-softwire-map-mib-00


Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF). Note that other groups may also distribute working
   documents as Internet-Drafts. The list of current Internet-Drafts is
   at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time. It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on September 4, 2012.

Copyright Notice

   Copyright (c) 2011 IETF Trust and the persons identified as the
   document authors. All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document. Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document. Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.










Fu, et al.            Expires September 4, 2012               [Page 1]


Internet-Draft    draft-fu-softwire-map-mib-00.txt          March 2012


Abstract

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols in the Internet community.
   In particular, it defines managed objects for MAP-E.

Table of Contents

   1. Introduction ................................................. 3
   2. The Internet-Standard Management Framework ................... 3
   3. Terminology .................................................. 3
   4. Structure of the MIB Module .................................. 3
      4.1. The mapTunnel Subtree ................................... 4
      4.2. The mapStatisticInfo Subtree ............................ 4
      4.3. The mapTrap Subtree ..................................... 4
      4.4. The mapConformance Subtree .............................. 4
   5. MIB modules required for IMPORTS ............................. 4
   6. Definitions .................................................. 4
   7. IANA Considerations ..........................................13
   8. Security Considerations ..................................... 13
   9. References .................................................. 14
      9.1. Normative References ................................... 14
      9.2. Informative References ................................. 15
   10. Change Log [RFC Editor please remove] ...................... 15
   Author's Addresses ............................................. 15























Fu, et al.            Expires September 4, 2012               [Page 2]


Internet-Draft    draft-fu-softwire-map-mib-00.txt          March 2012



1. Introduction

   MAP [I-D. draft-mdt-softwire-mapping-address-and-port] is a stateless
   mechanism for running IPv4 over IPv6-only infrastructure. In
   particular, it includes two solutions, MAP-E [I-D. draft-mdt-
   softwire-map-encapsulation] and MAP-T [I-D. draft-mdt-softwire-map-
   translation]. For the MAP-E, it provides an automatic tunnelling
   mechanism for providing IPv4 connectivity service to end users over a
   service provider's IPv6 network.

   This document defines a portion of the Management Information Base
   (MIB) for use with network management protocols in the Internet
   community. This MIB module may be used for monitoring the devices in
   the MAP-E scenario.

2. The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the MIB. MIB objects are generally accessed through the Simple
   Network Management Protocol (SNMP).

   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI).  This memo specifies a MIB
   module that is compliant to the SMIv2, which is described in
   [RFC2578], [RFC2579] and [RFC2580].

3. Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

4. Structure of the MIB Module

   The MAP-E MIB provides a way to configure and manage the devices in
   MAP-E scenario through SNMP.

   MAP-E MIB is configurable on a per-interface basis. It depends on
   several parts of the IF-MIB [RFC2863] and tunnel MIB [RFC4087].





Fu, et al.            Expires September 4, 2012               [Page 3]


Internet-Draft    draft-fu-softwire-map-mib-00.txt          March 2012


     4.1. The mapTunnel Subtree

   The mapTunnel subtree describes managed objects used for managing
   tunnels in the MAP-E scenario. Because the tunnel MIB supports the
   tunnel management function in MAP-E, we may reuse it in MAP-E MIB.
   However, a MAP BR is considered to be a collection of MAP tunnel
   endpoints which is distinguished by different mapping rules. It needs
   to extend the tunnel MIB by some parameters of mapping rule ID to
   distinguish the different tunnels.

     4.2. The mapStatisticInfo Subtree

   The mapStatisticInfo subtree provides state and statistical
   information for MAP BRs or MAP tunnel endpoints.

     4.3. The mapTrap Subtree

   The mapTrap Subtree provides trap information in MAP-E instance.

     4.4. The mapConformance Subtree

   The Subtree provides conformance information of MIB objects.

5. MIB modules required for IMPORTS

   This MIB module IMPORTs objects from [RFC4087], [RFC2580], [RFC2578],
   [RFC2863], [RFC4001], [RFC3411].

6. Definitions

      MAP-E-MIB DEFFINITIONS  ::=  BEGIN

      IMPORTS
         MODULE-IDENTITY, OBJECT-TYPE, mib-2, transmission,
         Gauge32, Integer32, Counter64
            FROM SNMPv2-SMI

         RowStatus, StorageType, DisplayString
            FROM SNMPv2-TC

         ifIndex, InterfaceIndexOrZero
            FROM IF-MIB

         InetAddress, InetAddressIPv6
         InetPortNumber, InetAddressPrefixLength
            FROM INET-ADDRESS-MIB



Fu, et al.            Expires September 4, 2012               [Page 4]


Internet-Draft    draft-fu-softwire-map-mib-00.txt          March 2012


         tunnelInetConfigIfIndex
            FROM tunnelMIB

      mapMIB MODULE-IDENTITY
      LAST-UPDATED "201203010000Z" -- March 01, 2012
      ORGANIZATION "IETF Softwire Working Group"
      CONTACT-INFO
         "Yu Fu
          Huawei Technologies Co., Ltd
          Huawei Building, 156 Beiqing Rd., Hai-Dian District
          Beijing, P.R. China 100095
          EMail: eleven.fuyu@huawei.com

          Sheng Jiang
          Huawei Technologies Co., Ltd
          Huawei Building, 156 Beiqing Rd., Hai-Dian District
          Beijing, P.R. China 100095
          EMail: jiangsheng@huawei.com

          Jiang Dong
          Tsinghua University
          Department of Computer Science, Tsinghua University
          Beijing  100084
          P.R. China
          Email: dongjiang @csnet1.cs.tsinghua.edu.cn

          Peng Wu
          Tsinghua University
          Department of Computer Science, Tsinghua University
          Beijing  100084
          P.R. China
          Email: weapon@csnet1.cs.tsinghua.edu.cn"

      DESCRIPTION
         "The MIB module is defined for management of object in the
         MAP-E scenario."
         ::=  {  transmission xxx  }  --xxx to be replaced with correct
         value

       mapTunnel   OBJECT IDENTIFIER
         :: =  { mapMIB 1 }

       mapStatisticInfo   OBJECT IDENTIFIER
         :: =  { mapMIB 2 }

       mapTraps  OBJECT IDENTIFIER
         ::=  { mapMIB 3 }


Fu, et al.            Expires September 4, 2012               [Page 5]


Internet-Draft    draft-fu-softwire-map-mib-00.txt          March 2012


       --Conformance
       mapConformance   OBJECT IDENTIFIER
         :: =  { mapMIB 4 }

          --mapTunnel
          --mapTunnelTable

      mapTunnelTable OBJECT-TYPE
         SYNTAX     SEQUENCE OF mapTunnelEntry
         MAX-ACCESS  not-accessible
         STATUS     current
         DESCRIPTION
            "The (conceptual) table containing information on configured
             tunnels. This table can be used to map CE address to the
             associated BR address. It can also be used for row
             creation."
         :: =  { mapTunnel 1 }

      mapTunnelEntry OBJECT-TYPE
         SYNTAX     mapTunnelEntry
         MAX-ACCESS  not-accessible
         STATUS     current
         DESCRIPTION
            "Each entry in this table contains the information on a
             particular configured tunnel."
             INDEX   { mapTunnelBRAddress,
                       mapTunnelMapRuleID}
         :: =  { mapTunnelTable 1 }

      mapTunnelEntry  :: =
         SEQUENCE {
          mapTunnelBRAddress            InetAddressIPv6,
          mapTunnelMapRuleID            Integer32,
          mapTunnelMapRuleIPv6Prefix    InetAddressIPv6,
          mapTunnelMapRuleIPv6PrefixLen InetAddressPrefixLength,
          mapTunnelMapRuleIPv4Prefix    InetAddress,
          mapTunnelMapRuleIPv4PrefixLen InetAddressPrefixLength,
          mapTunnelMAPRuleExPorts       InetPortNumber,
          mapTunnelMAPEALen             Integer32,
          mapTunnelCEAddress            InetAddressIPv6,
          mapTunnelID                   Integer32,
          mapTunnelIfIndex              tunnelInetConfigIfIndex,
          mapTunnelStatus               RowStatus,
          mapTunnelStorageType          StorageType
      }




Fu, et al.            Expires September 4, 2012               [Page 6]


Internet-Draft    draft-fu-softwire-map-mib-00.txt          March 2012


      mapTunnelBRAddress OBJECT-TYPE
          SYNTAX     InetAddressIPv6
          MAX-ACCESS read-create
          STATUS     current
          DESCRIPTION
             "The address of the BR. It is one endpoint of the MAP
              Tunnel"
          ::= { mapTunnelEntry 1 }

      mapTunnelMapRuleID OBJECT-TYPE
          SYNTAX Integer32 (1..2147483647)
          MAX-ACCESS read-create
          STATUS current
          DESCRIPTION
             "An identifier used to distinguish the multiple mapping
              rule which is unique with each CE in the same BR."
          ::= { mapTunnelEntry 2 }

      mapTunnelMapRuleIPv6Prefix OBJECT-TYPE
          SYNTAX     InetAddressIPv6
          MAX-ACCESS read-create
          STATUS     current
          DESCRIPTION
             "The IPv6 prefix defined in mapping rule which will be
              assigned to CE ."
          ::= { mapTunnelEntry 3 }

      mapTunnelMapRuleIPv6PrefixLen OBJECT-TYPE
          SYNTAX     InetAddressPrefixLength
          MAX-ACCESS read-create
          STATUS     current
          DESCRIPTION
             "The length of the IPv6 prefix defined in the mapping rule.
              As a parameter for mapping rule, it will be also assigned
              to CE."
          ::= { mapTunnelEntry 4 }

      mapTunnelMapRuleIPv4Prefix OBJECT-TYPE
          SYNTAX     InetAddress
          MAX-ACCESS read-create
          STATUS     current
          DESCRIPTION
             " The IPv4 prefix defined in mapping rule which will be
              assigned to CE."
          ::= { mapTunnelEntry 5 }




Fu, et al.            Expires September 4, 2012               [Page 7]


Internet-Draft    draft-fu-softwire-map-mib-00.txt          March 2012


      mapTunnelMapRuleIPv4PrefixLen OBJECT-TYPE
          SYNTAX     InetAddressPrefixLength
          MAX-ACCESS read-create
          STATUS     current
          DESCRIPTION
             "The length of the IPv4 prefix defined in the mapping
              rule. As a parameter for mapping rule, it will be also
              assigned to CE."
          ::= { mapTunnelEntry 6 }

      mapTunnelMAPRuleExPorts OBJECT-TYPE
          SYNTAX     InetPortNumber
          MAX-ACCESS read-create
          STATUS     current
          DESCRIPTION
             "The upper bound for range of excluded ports
              defined in mapping rule which will be assigned to CE."
          ::= { mapTunnelEntry 7 }

      mapTunnelMAPEALen OBJECT-TYPE
          SYNTAX     Integer32
          MAX-ACCESS read-create
          STATUS     current
          DESCRIPTION
             "The length of the Embedded-Address (EA) defined in
              mapping rule which will be assigned to CE."
          ::= { mapTunnelEntry 8 }

      mapTunnelCEAddress OBJECT-TYPE
          SYNTAX     InetAddressIPv6
          MAX-ACCESS read-create
          STATUS     current
          DESCRIPTION
             "The address of the CE as the another endpoint of MAP
              tunnel. It is derived by the parameters defined in the
              mapping rule assigned to the CE."
          ::= { mapTunnelEntry 9 }

      mapTunnelID OBJECT-TYPE
          SYNTAX     Integer32 (1..2147483647)
          MAX-ACCESS read-create
          STATUS     current
          DESCRIPTION
             "An identifier used to distinguish between multiple
              tunnels in MAP-E scenario."
          ::= { mapTunnelEntry 10 }



Fu, et al.            Expires September 4, 2012               [Page 8]


Internet-Draft    draft-fu-softwire-map-mib-00.txt          March 2012


      mapTunnelIfIndex OBJECT-TYPE
          SYNTAX     tunnelInetConfigIfIndex
          MAX-ACCESS read-only
          STATUS     current
          DESCRIPTION
             "If the value of mapTunnelStatus for this row
              is active, then this object contains the value of
              ifIndex corresponding to the tunnel interface. A
              value of 0 is not legal in the active state,
              and means that the interface index has not
              yet been assigned."
          ::= { mapTunnelEntry 11 }

      mapTunnelStatus OBJECT-TYPE
          SYNTAX     RowStatus
          MAX-ACCESS read-create
          STATUS     current
          DESCRIPTION
             "The status of this row, by which new entries may be
              created, or old entries deleted from this table.
          ::= { mapTunnelEntry 12 }

      mapTunnelStorageType OBJECT-TYPE
          SYNTAX     StorageType
          MAX-ACCESS read-create
          STATUS     current
          DESCRIPTION
             "The storage type of this row. If the row is
              permanent(4), no objects in the row need be
              writable."
          ::= { mapTunnelEntry 13 }

       --mapStatisticInfo

      mapStatisticTable OBJECT-TYPE
         SYNTAX SEQUENCE OF mapStatisticEntry
         MAX-ACCESS not-accessible
         STATUS current
         DESCRIPTION
            "This table provides some statistical information
             of MAP-E instance."
         ::= { mapStatisticInfo 1 }

      mapStatisticEntry OBJECT-TYPE
         SYNTAX dsliteStatisticEntry
         MAX-ACCESS not-accessible
         STATUS current


Fu, et al.            Expires September 4, 2012               [Page 9]


Internet-Draft    draft-fu-softwire-map-mib-00.txt          March 2012


         DESCRIPTION
            "This table provides statistical information
             of MAP-E instance."
         INDEX { mapStatisticBRAddress }
         ::= { mapStatisticTable 1 }

      mapStatisticEntry ::=
         SEQUENCE {
       mapStatisticBRAddress              InetAddressIPv6,
       mapStatisticDiscard                Counter64,
       mapStatisticReceived               Counter64,
       mapStatisticTransmitted            Counter64,
       mapStatisticConnections            Integer32,
       mapStatisticSpecificIP             DisplayString,
       mapStatisticStorageType            StorageType,
       mapStatisticRowStatus              RowStatus
      }

      mapStatisticBRAddress OBJECT-TYPE
          SYNTAX     InetAddressIPv6
          MAX-ACCESS read-create
          STATUS     current
          DESCRIPTION
             "The address of the BR. It is one endpoint of the MAP-E
              Tunnel"
          ::= { mapStatisticEntry 1 }

      mapStatisticDiscard OBJECT-TYPE
         SYNTAX Counter64
         MAX-ACCESS read-create
         STATUS current
         DESCRIPTION
            " This object indicate the count number of
              the discarded packet."
        ::= { mapStatisticEntry 2 }

      mapStatisticReceived OBJECT-TYPE
         SYNTAX Counter64
         MAX-ACCESS read-create
         STATUS current
         DESCRIPTION
            "This object indicate the count number of
             received packet count."
         ::= { mapStatisticEntry 3 }

      mapStatisticTransmitted OBJECT-TYPE
         SYNTAX Counter64


Fu, et al.            Expires September 4, 2012              [Page 10]


Internet-Draft    draft-fu-softwire-map-mib-00.txt          March 2012


         MAX-ACCESS read-create
         STATUS current
         DESCRIPTION
            "This object indicate the count number of
             transmitted packet count."
         ::= { mapStatisticEntry 4 }

      mapStatisticConnections OBJECT-TYPE
         SYNTAX Integer32 (60..90)
         MAX-ACCESS read-write
         STATUS current
         DESCRIPTION
            " This object indicate the threshold of tunnel
              connections for this BR."
         ::= { mapStatisticEntry 5 }

      mapStatisticSpecificIP OBJECT-TYPE
         SYNTAX DisplayString
         MAX-ACCESS accessible-for-notify
         STATUS current
         DESCRIPTION
            " This object indicate the IP address of CE whose port usage
             reach threshold."
         ::= { mapStatisticEntry 6 }

   ---map trap

      mapTunnelNumAlarm NOTIFICATION-TYPE
         STATUS current
         DESCRIPTION
            "This trap is triggered when MAP-E tunnels
             reach the threshold."
         ::= { mapTraps 1 }

      mapBRPortUsageOfSpecificIpAlarm NOTIFICATION-TYPE
         OBJECTS { mapStatisticSpecificIP }
         STATUS current
         DESCRIPTION
            "This trap is triggered when the used ports of
             specific CE address reach the threshold."
         ::= { dsliteTraps 2 }

       --Module Conformance statement

      mapCompliances OBJECT IDENTIFIER ::= { mapConformance 1 }




Fu, et al.            Expires September 4, 2012              [Page 11]


Internet-Draft    draft-fu-softwire-map-mib-00.txt          March 2012


      mapCompliance MODULE-COMPLIANCE
         STATUS current
         DESCRIPTION
            "Description."
         MODULE -- this module
             MANDATORY-GROUPS { mapTunnelGroup,
                 mapStatisticInfoGroup }
        ::= { mapCompliances 1 }

      mapGroups OBJECT IDENTIFIER ::= { mapConformance 2 }

      mapTunnelGroup OBJECT-GROUP
         OBJECTS { mapTunnelBRAddress, mapTunnelMapRuleID,
                 mapTunnelMapRuleIPv6Prefix,
                 mapTunnelMapRuleIPv6PrefixLen,
                 mapTunnelMapRuleIPv4Prefix,
                 mapTunnelMapRuleIPv4PrefixLen,
                 mapTunnelMAPRuleExPorts, mapTunnelMAPEALen,
                 mapTunnelCEAddress, mapTunnelID,
                 mapTunnelIfIndex, mapTunnelStatus,
                 mapTunnelStorageType }
         STATUS current
         DESCRIPTION
            " The collection of this objects are used to give the
             information for tunnels in MAP-E."
         ::= { mapGroups 1 }

      mapStatisticGroup OBJECT-GROUP
         OBJECTS { mapStatisticBRAddress,
                   mapStatisticDiscard,
                   mapStatisticReceived,
                   mapStatisticTransmitted,
                   mapStatisticConnections,
                   mapStatisticSpecificIP,
                   mapStatisticStorageType,
                   mapStatisticRowStatus }
        STATUS current
        DESCRIPTION
           " The collection of this objects are used to give the
             statistical information of MAP-E."
        ::= { mapGroups 2 }

      mapTrapsGroup NOTIFICATION-GROUP
         NOTIFICATIONS { mapTunnelNumAlarm,
                         mapBRPortUsageOfSpecificIpAlarm }
         STATUS current
         DESCRIPTION


Fu, et al.            Expires September 4, 2012              [Page 12]


Internet-Draft    draft-fu-softwire-map-mib-00.txt          March 2012


            "The collection of this objects are used to give the
             trap information for MAP-E."
         ::= { mapGroups 3 }

             END

7. IANA Considerations

   The MIB module in this document uses the following IANA-assigned
   OBJECT IDENTIFIER values recorded in the SMI Numbers registry:

      Descriptor        OBJECT IDENTIFIER value
      ----------        -----------------------
      MAP-E-MIB          { transmission XXX }

8. Security Considerations

   The MAP-E MIB module can be used for configuration of certain
   objects, and anything that can be configured can be incorrectly
   configured, with potentially disastrous results. Because this
   MIB module reuses the IP tunnel MIB, the security considerations
   for these MIBs are also applicable to the MAP-E MIB.

   SNMP versions prior to SNMPv3 did not include adequate security.
   Even if the network itself is secure (for example by using IPSec),
   even then, there is no control as to who on the secure network is
   allowed to access and GET/SET (read/change/create/delete) the objects
   in this MIB module.

   It is RECOMMENDED that implementers consider the security features as
   provided by the SNMPv3 framework (see [RFC3410], section 8),
   including full support for the SNMPv3 cryptographic mechanisms (for
   authentication and privacy).

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module is properly configured to give access to
   the objects only to those principles (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.








Fu, et al.            Expires September 4, 2012              [Page 13]


Internet-Draft    draft-fu-softwire-map-mib-00.txt          March 2012


9. References

     9.1. Normative References

   [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
             Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
             "Structure of Management Information Version 2 (SMIv2)",
             RFC 2578, April 1999.

   [RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Textual
             Conventions for SMIv2", RFC 2579, April 1999.

   [RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
             "Conformance Statements for SMIv2", RFC 2580, April 1999.

   [RFC2863] McCloghrie, K. and F. Kastenholz. "The Interfaces Group
             MIB", RFC 2863, June 2000.

   [RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
             Architecture for Describing Simple Network Management
             Protocol (SNMP) Management Frameworks", RFC 3411, December
             2002.

   [RFC4001] Daniele, M., Haberman, B., Routhier, S., and J.
             Schoenwaelder, "Textual Conventions for Internet Network
             Addresses", RFC 4001, February 2005.

   [RFC4087] Thaler, D., "IP Tunnel MIB", RFC 4087, June 2005.

   [I-D.mdt-softwire-mapping-address-and-port]
             Troan, O.,etc., "Mapping of Address and Port (MAP)", draft-
             mdt-softwire-mapping-address-and-port, working in progress.

   [I-D.mdt-softwire-map-dhcp-option]
             Mrugalski, T.,etc., "DHCPv6 Options for Mapping of Address
             and Port", draft-mdt-softwire-map-dhcp-option, working in
             progress.

   [I-D.mdt-softwire-map-encapsulation]
             Mrugalski, T., etc., "MAP Encapsulation (MAP-E) -
             specification", draft-mdt-softwire-map-encapsulation,
             working in progress.





Fu, et al.            Expires September 4, 2012              [Page 14]


Internet-Draft    draft-fu-softwire-map-mib-00.txt          March 2012


   [I-D.mdt-softwire-map-translation]
             Mrugalski, T., etc., "MAP Translation (MAP-T) -
             specification", draft-mdt-softwire-map-translation, working
             in progress.

     9.2. Informative References

   [RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart,
             "Introduction and Applicability Statements for Internet-
             Standard Management Framework", RFC 3410, December 2002.

10. Change Log [RFC Editor please remove]

   draft-fu-softwire-map-mib-00, original version, 2012-03-01

Author's Addresses

   Yu Fu
   Huawei Technologies Co., Ltd
   Huawei Building, 156 Beiqing Rd.,
   Hai-Dian District, Beijing 100095
   P.R. China
   Email: eleven.fuyu@huawei.com

   Sheng Jiang
   Huawei Technologies Co., Ltd
   Huawei Building, 156 Beiqing Rd.,
   Hai-Dian District, Beijing 100095
   P.R. China
   Email: jiangsheng@huawei.com

   Jiang Dong
   Tsinghua University
   Department of Computer Science, Tsinghua University
   Beijing  100084
   P.R. China
   Email: dongjiang@csnet1.cs.tsinghua.edu.cn

   Peng Wu
   Tsinghua University
   Department of Computer Science, Tsinghua University
   Beijing  100084
   P.R. China
   Email: weapon@csnet1.cs.tsinghua.edu.cn





Fu, et al.            Expires September 4, 2012              [Page 15]


Html markup produced by rfcmarkup 1.129b, available from https://tools.ietf.org/tools/rfcmarkup/