[Docs] [txt|pdf] [Tracker] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 draft-gandhi-spring-rfc6374-srpm-mpls

SPRING Working Group                                      R. Gandhi, Ed.
Internet-Draft                                               C. Filsfils
Intended Status: Informational                                   S. Soni
Expires: January 16, 2019                            Cisco Systems, Inc.
                                                                D. Voyer
                                                             Bell Canada
                                                              S. Salsano
                                        Universita di Roma "Tor Vergata"
                                                            P. L. Ventre
                                                                    CNIT
                                                                 M. Chen
                                                                  Huawei
                                                           July 15, 2018


                      Performance Measurement in
              Segment Routing Networks with MPLS Data Plane
                   draft-gandhi-spring-sr-mpls-pm-02

Abstract

   RFC 6374 specifies protocol mechanisms to enable the efficient and
   accurate measurement of packet loss, one-way and two-way delay, as
   well as related metrics such as delay variation in MPLS networks
   using probe messages.  This document reviews how these mechanisms can
   be used for Delay and Loss Performance Measurements (PM) in Segment
   Routing (SR) networks with MPLS data plane (SR-MPLS), for both SR
   links and end-to-end SR Policies.  The performance measurements for
   SR links are used to compute extended Traffic Engineering (TE)
   metrics for delay and loss and are advertised in the network using
   routing protocols.


Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."




Gandhi, et al.          Expires January 16, 2019                [Page 1]


Internet-Draft      SR-MPLS Performance Measurement        July 15, 2018


Copyright Notice

   Copyright (c) 2018 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.



Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
   2.  Conventions Used in This Document  . . . . . . . . . . . . . .  3
     2.1.  Abbreviations  . . . . . . . . . . . . . . . . . . . . . .  3
     2.2.  Reference Topology . . . . . . . . . . . . . . . . . . . .  4
   3.  Probe Query and Response Packets . . . . . . . . . . . . . . .  5
     3.1.  Probe Packet Header for SR-MPLS Policies . . . . . . . . .  5
     3.2.  Probe Packet Header for SR-MPLS Links  . . . . . . . . . .  5
     3.3.  Probe Response Message for SR-MPLS Links and Policies  . .  6
       3.3.1.  One-way Measurement Probe Response Message . . . . . .  6
       3.3.2.  Two-way Measurement Probe Response Message . . . . . .  6
   4.  Performance Delay Measurement  . . . . . . . . . . . . . . . .  6
     4.1.  Delay Measurement Message Format . . . . . . . . . . . . .  6
     4.2.  Timestamp  . . . . . . . . . . . . . . . . . . . . . . . .  8
   5.  Performance Loss Measurement . . . . . . . . . . . . . . . . .  8
     5.1.  Loss Measurement Message Format  . . . . . . . . . . . . .  8
   6.  SR Link Extended TE Metrics Advertisements . . . . . . . . . . 10
   7.  Security Considerations  . . . . . . . . . . . . . . . . . . . 10
   8.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 10
   9.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 11
     9.1.  Normative References . . . . . . . . . . . . . . . . . . . 11
     9.2.  Informative References . . . . . . . . . . . . . . . . . . 11
   Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . . . . 13
   Contributors . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 13








Gandhi, et al.          Expires January 16, 2019                [Page 2]


Internet-Draft      SR-MPLS Performance Measurement        July 15, 2018


1.  Introduction

   Service provider's ability to satisfy Service Level Agreements (SLAs)
   depend on the ability to measure and monitor performance metrics for
   packet loss and one-way and two-way delay, as well as related metrics
   such as delay variation.  The ability to monitor these performance
   metrics also provides operators with greater visibility into the
   performance characteristics of their networks, thereby facilitating
   planning, troubleshooting, and network performance evaluation.

   [RFC6374] specifies protocol mechanisms to enable the efficient and
   accurate measurement of these performance metrics in MPLS networks
   using probe messages.  The One-Way Active Measurement Protocol
   (OWAMP) defined in [RFC4656] and Two-Way Active Measurement Protocol
   (TWAMP) defined in [RFC5357] provide capabilities for the measurement
   of various performance metrics in IP networks.  However, mechanisms
   defined in [RFC6374] are more suitable for Segment Routing (SR) when
   using MPLS data plane (SR-MPLS).  In addition, [RFC6374] also
   supports IEEE 1588 timestamps [IEEE1588] and "direct mode" Loss
   Measurement (LM), which are required in SR networks.

   [RFC7876] specifies the procedures to be used when sending and
   processing out-of-band performance measurement probe replies over an
   UDP return path when receiving RFC 6374 based probe queries.  These
   procedures can be used to send out-of-band PM replies for both SR
   links and SR Policies for one-way measurement.

   This document reviews how probe based mechanisms defined in [RFC6374]
   can be used for Delay and Loss Performance Measurements (PM) in SR
   networks with MPLS data plane, for both SR links and end-to-end SR
   Policies.  The performance measurements for SR links are used to
   compute extended Traffic Engineering (TE) metrics for delay and loss
   and are advertised in the network using routing protocols.


2.  Conventions Used in This Document

2.1.  Abbreviations

   ACH: Associated Channel Header.

   DFLag: Data Format Flag.

   DM: Delay Measurement.

   ECMP: Equal Cost Multi-Path.

   G-ACh: Generic Associated Channel (G-ACh)



Gandhi, et al.          Expires January 16, 2019                [Page 3]


Internet-Draft      SR-MPLS Performance Measurement        July 15, 2018


   GAL: Generic Associated Channel (G-ACh) Label

   LM: Loss Measurement.

   MPLS: Multiprotocol Label Switching.

   PM: Performance Measurement.

   PTP: Precision Time Protocol.

   SID: Segment ID.

   SR: Segment Routing.

   TC: Traffic Class.

   TE: Traffic Engineering.

   URO: UDP Return Object.


2.2.  Reference Topology

   In the reference topology shown in Figure 1, the querier node R1
   initiates a performance measurement probe query and the responder
   node R5 sends a probe response for the query message received.  The
   probe response is sent to the querier node R1.  The nodes R1 and R5
   may be directly connected via a link enabled with Segment Routing or
   there exists an SR Policy [I-D.spring-segment-routing-policy] on node
   R1 with destination to node R5.


             +-------+        Query        +-------+
             |       | - - - - - - - - - ->|       |
             |   R1  |---------------------|   R5  |
             |       |<- - - - - - - - - - |       |
             +-------+       Response      +-------+

                   Figure 1: Reference Topology


   Both delay and loss performance measurement is performed for the
   traffic traversing between node R1 and node R5.  One-way delay and
   two-way delay measurements are defined in Section 2.4 of [RFC6374].
   Transmit and Receive packet loss measurements are defined in Section
   2.2 of [RFC6374].  One-way loss measurement provides transmit packet
   loss whereas two-way loss measurement provides both transmit and
   receive packet loss.



Gandhi, et al.          Expires January 16, 2019                [Page 4]


Internet-Draft      SR-MPLS Performance Measurement        July 15, 2018


3.  Probe Query and Response Packets

3.1.  Probe Packet Header for SR-MPLS Policies

   As described in Section 2.9.1 of [RFC6374], MPLS PM probe query and
   response messages flow over the MPLS Generic Associated Channel (G-
   ACh).  A probe packet for an end-to-end measurement for SR Policy
   contains SR-MPLS label stack [I-D.spring-segment-routing-policy],
   with the G-ACh Label (GAL) at the bottom of the stack.  The GAL is
   followed by an Associated Channel Header (ACH), which identifies the
   message type and the message payload following the ACH as shown in
   Figure 2.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                  Label(0)             | EXP |S|      TTL      |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    .                                                               .
    .                                                               .
    .                                                               .
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                  Label(n)             | EXP |S|      TTL      |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                  GAL                  | EXP |S|      TTL      |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |0 0 0 1|Version|  Reserved     | GAL Channel Type              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

     Figure 2: Probe Packet Header for an End-to-end SR-MPLS Policy

   The SR-MPLS label stack can be empty to indicate Implicit NULL label
   case.

3.2.  Probe Packet Header for SR-MPLS Links

   As described in Section 2.9.1 of [RFC6374], MPLS PM probe query and
   response messages flow over the MPLS Generic Associated Channel (G-
   ACh).  A probe packet for SR-MPLS links contains G-ACh Label (GAL).
   The GAL is followed by an Associated Channel Header (ACH), which
   identifies the message type, and the message payload following the
   ACH as shown in Figure 3.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                  GAL                  | EXP |S|      TTL      |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+



Gandhi, et al.          Expires January 16, 2019                [Page 5]


Internet-Draft      SR-MPLS Performance Measurement        July 15, 2018


    |0 0 0 1|Version|  Reserved     | GAL Channel Type              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

            Figure 3: Probe Packet Header for an SR-MPLS Link


3.3.  Probe Response Message for SR-MPLS Links and Policies

3.3.1.  One-way Measurement Probe Response Message

   For one-way performance measurement [RFC7679], the PM querier node
   can receive "out-of-band" probe replies by properly setting the UDP
   Return Object (URO) TLV in the probe query message.  The URO TLV
   (Type=131) is defined in [RFC7876] and includes the
   UDP-Destination-Port and IP Address.  In particular, if the querier
   sets its own IP address in the URO TLV, the probe response is sent
   back by the responder node to the querier node.  In addition, the
   "control code" in the probe query message is set to "out-of-band
   response requested".

3.3.2.  Two-way Measurement Probe Response Message

   For two-way performance measurement [RFC6374], when using a
   bidirectional channel, the probe response message is sent back to the
   querier node in-band on the reverse direction SR Link or SR Policy
   using a message with format similar to their probe query message.  In
   this case, the "control code" in the probe query message is set to
   "in-band response requested".


4.  Performance Delay Measurement

4.1.  Delay Measurement Message Format

   As defined in [RFC6374], MPLS DM probe query and response messages
   use Associated Channel Header (ACH) (value 0x000C for delay
   measurement) [RFC6374], which identifies the message type, and the
   message payload following the ACH.  For both SR links and end-to-end
   measurement for SR Policies, the same MPLS DM ACH value is used.

   The DM message payload as defined in [RFC6374] is used for SR-MPLS
   delay measurement, for both SR links and end-to-end SR Policies.  The
   DM message payload format is defined as following in [RFC6374]:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |Version| Flags |  Control Code |           Message Length      |



Gandhi, et al.          Expires January 16, 2019                [Page 6]


Internet-Draft      SR-MPLS Performance Measurement        July 15, 2018


    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  QTF  |  RTF  | RPTF  |               Reserved                |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                       Session Identifier          |    DS     |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                           Timestamp 1                         |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    .                                                               .
    .                                                               .
    .                                                               .
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                           Timestamp 4                         |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    ~                           TLV Block                           ~
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

           Figure 4: Delay Measurement Message Payload Format

   The meanings of the fields are summarized in the following table, see
   [RFC6374] for details.

    Field                 Meaning
    -------------------  ----------------------------------------------
    Version               Protocol version

    Flags                 Message control flags

    Control Code          Code identifying the query or response type

    QTF                   Querier timestamp format
                          (see Section 3.4 of [RFC6374])

    RTF                   Responder timestamp format
                          (see Section 3.4 of [RFC6374])

    RPTF                  Responder's preferred timestamp format

    Reserved              Reserved for future specification

    Session Identifier    Set arbitrarily by the querier

    Differentiated        Differentiated Services Code Point (DSCP)
    Services (DS) Field   being measured

    Timestamp 1-4         64-bit timestamp values
                          (see Section 3.4 of [RFC6374])



Gandhi, et al.          Expires January 16, 2019                [Page 7]


Internet-Draft      SR-MPLS Performance Measurement        July 15, 2018


    TLV Block             Optional block of Type-Length-Value fields


4.2.  Timestamp

   The Section 3.4 of [RFC6374] defines timestamp format that can be
   used for delay measurement.  The IEEE 1588 Precision Time Protocol
   (PTP) timestamp format [IEEE1588] is used by default as described in
   Appendix A of [RFC6374], but it may require hardware support.  As an
   alternative, Network Time Protocol (NTP) timestamp format can also be
   used [RFC6374].

   Note that for one-way delay measurement, clock synchronization
   between the querier and responder nodes using the methods detailed in
   [RFC6374] is required.  The two-way delay measurement does not
   require clock to be synchronized between the querier and responder
   nodes.

5.  Performance Loss Measurement

   The LM protocol can perform two distinct kinds of loss measurement as
   described in Section 2.9.8 of [RFC6374].

   o  In inferred mode, LM will measure the loss of specially generated
      test messages in order to infer the approximate data plane loss
      level.  Inferred mode LM provides only approximate loss
      accounting.

   o  In direct mode, LM will directly measure data plane packet loss.
      Direct mode LM provides perfect loss accounting, but may require
      hardware support.

   For both of these modes of LM, path segment identifier
   [I-D.spring-mpls-path-segment] can be used for measuring traffic on
   the egress node.

5.1.  Loss Measurement Message Format

   As defined in [RFC6374], MPLS LM probe query and response messages
   use Associated Channel Header (ACH) (value 0x000A for direct loss
   measurement or value 0x000B for inferred loss measurement), which
   identifies the message type, and the message payload following the
   ACH.  For both SR links and end-to-end measurement for SR Policies,
   the same MPLS LM ACH value is used.

   The LM message payload as defined in [RFC6374] is used for SR-MPLS
   loss measurement, for both SR links and end-to-end SR Policies.  The
   LM message payload format is defined as following in [RFC6374]:



Gandhi, et al.          Expires January 16, 2019                [Page 8]


Internet-Draft      SR-MPLS Performance Measurement        July 15, 2018


    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |Version| Flags |  Control Code |        Message Length         |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | DFlags|  OTF  |                   Reserved                    |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                       Session Identifier          |    DS     |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                        Origin Timestamp                       |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                           Counter 1                           |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    .                                                               .
    .                                                               .
    .                                                               .
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                           Counter 4                           |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    ~                           TLV Block                           ~
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

            Figure 5: Loss Measurement Message Payload Format

   The meanings of the fields are summarized in the following table, see
   [RFC6374] for details.

    Field                 Meaning
    --------------------  ----------------------------------------------
    Version               Protocol version

    Flags                 Message control flags

    Control Code          Code identifying the query or response type

    Message Length        Total length of this message in bytes

    Data Format Flags     Flags specifying the format of message data
    (DFlags)

    Origin Timestamp      Format of the Origin Timestamp field
    Format (OTF)

    Reserved              Reserved for future specification




Gandhi, et al.          Expires January 16, 2019                [Page 9]


Internet-Draft      SR-MPLS Performance Measurement        July 15, 2018


    Session Identifier    Set arbitrarily by the querier

    Differentiated        Differentiated Services Code Point (DSCP)
    Services (DS) Field   being measured

    Origin Timestamp      64-bit field for query message transmission
                          timestamp

    Counter 1-4           64-bit fields for LM counter values

    TLV Block             Optional block of Type-Length-Value fields


6.  SR Link Extended TE Metrics Advertisements

   The extended TE metrics for SR link delay and loss computed using the
   performance measurement procedures reviewed in this document can be
   advertised in the routing domain as follows:

   o  For OSPF, ISIS, and BGP-LS, protocol extensions defined in
      [RFC7471], [RFC7810] [I-D.lsr-isis-rfc7810bis], and
      [I-D.idr-te-pm-bgp] are used, respectively for advertising the
      extended TE link metrics in the network.

   o  The extended link delay metrics advertised are minimum-delay,
      maximum-delay, average-delay and delay-variance for one-way.

   o  The delay-variance is computed as specified in Section 4.2 of
      [RFC5481].

   o  The one-way delay metrics can be computed using two-way
      measurement by dividing the measured delay values by 2.

   o  The extended TE link loss metric advertised is one-way percentage
      packet loss.


7.  Security Considerations

   This document reviews the procedures for performance measurement for
   SR-MPLS networks, for both SR-MPLS links and end-to-end SR-MPLS
   Policies using the mechanisms defined in [RFC6374].  This document
   does not introduce any additional security considerations other than
   those covered in [RFC6374], [RFC7471], [RFC7810].


8.  IANA Considerations




Gandhi, et al.          Expires January 16, 2019               [Page 10]


Internet-Draft      SR-MPLS Performance Measurement        July 15, 2018


   This document does not require any IANA actions.


9.  References

9.1.  Normative References

   [RFC6374]  Frost, D. and S. Bryant, "Packet Loss and Delay
              Measurement for MPLS networks', RFC 6374, September 2011.

   [RFC7876]  Bryant, S., Sivabalan, S., and Soni, S., "UDP Return Path
              for Packet Loss and Delay Measurement for MPLS Networks",
              RFC 7876, July 2016.

9.2.  Informative References

   [IEEE1588] IEEE, "1588-2008 IEEE Standard for a Precision Clock
              Synchronization Protocol for Networked Measurement and
              Control Systems", March 2008.

   [RFC4656]  Shalunov, S., Teitelbaum, B., Karp, A., Boote, J., and M.
              Zekauskas, "A One-way Active Measurement Protoco (OWAMP)",
              RFC 4656, September 2006.

   [RFC5357]  Hedayat, K., Krzanowski, R., Morton, A., Yum, K., and J.
              Babiarz, "A Two-Way Active Measurement Protocol (TWAMP)",
              RFC 5357, October 2008.

   [RFC5481]  Morton, A. and B. Claise, "Packet Delay Variation
              Applicability Statement", RFC 5481, March 2009.

   [RFC7679]  Almes, G., et al., "A One-Way Delay Metric for IP
              Performance Metrics (IPPM)', RFC 7679, January 2016.

   [RFC7471]  Giacalone, S., et al., "OSPF Traffic Engineering (TE)
              Metric Extensions", RFC 7471, March 2015.

   [RFC7810]  Previdi, S., et al., "IS-IS Traffic Engineering (TE)
              Metric Extensions", RFC 7810, May 2016.

   [I-D.lsr-isis-rfc7810bis]  Ginsberg, L., et al., "IS-IS Traffic
              Engineering (TE) Metric Extensions",
              draft-ietf-lsr-isis-rfc7810bis, work in progress.

   [I-D.idr-te-pm-bgp]  Ginsberg, L. Ed., et al., "BGP-LS Advertisement
              of IGP Traffic Engineering Performance Metric Extensions",
              draft-ietf-idr-te-pm-bgp, work in progress.




Gandhi, et al.          Expires January 16, 2019               [Page 11]


Internet-Draft      SR-MPLS Performance Measurement        July 15, 2018


   [I-D.spring-segment-routing-policy]  Filsfils, C., et al., "Segment
              Routing Policy Architecture",
              draft-ietf-spring-segment-routing-policy, work in
              progress.

   [I-D.spring-mpls-path-segment]  Cheng, W., et al., 'Path Segment in
              MPLS Based Segment Routing Network',
              draft-cheng-spring-mpls-path-segment, work in progress.











































Gandhi, et al.          Expires January 16, 2019               [Page 12]


Internet-Draft      SR-MPLS Performance Measurement        July 15, 2018


Acknowledgments

   To be added.


Contributors

   Patrick Khordoc
   Cisco Systems, Inc.
   Email: pkhordoc@cisco.com


   Zafar Ali
   Cisco Systems, Inc.
   Email: zali@cisco.com


   Daniel Bernier
   Bell Canada
   Email: daniel.bernier@bell.ca


Authors' Addresses

   Rakesh Gandhi (editor)
   Cisco Systems, Inc.
   Canada
   Email: rgandhi@cisco.com


   Clarence Filsfils
   Cisco Systems, Inc.
   Email: cfilsfil@cisco.com


   Sagar Soni
   Cisco Systems, Inc.
   Email: sagsoni@cisco.com


   Daniel Voyer
   Bell Canada
   Email: daniel.voyer@bell.ca


   Stefano Salsano
   Universita di Roma "Tor Vergata"
   Italy



Gandhi, et al.          Expires January 16, 2019               [Page 13]


Internet-Draft      SR-MPLS Performance Measurement        July 15, 2018


   Email: stefano.salsano@uniroma2.it


   Pier Luigi Ventre
   CNIT
   Italy
   Email: pierluigi.ventre@cnit.it


   Mach(Guoyi) Chen
   Huawei
   Email: mach.chen@huawei.com







































Gandhi, et al.          Expires January 16, 2019               [Page 14]


Html markup produced by rfcmarkup 1.129c, available from https://tools.ietf.org/tools/rfcmarkup/