[Docs] [txt|pdf|xml|html] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits] [IPR]

Versions: (draft-thubert-6tisch-architecture) 00 01 02 03 04 05 06 07 08 09 10 11 12

6TiSCH                                                   P. Thubert, Ed.
Internet-Draft                                                     Cisco
Intended status: Standards Track                             T. Watteyne
Expires: August 16, 2014                               Linear Technology
                                                            RA. Assimiti
                                                                 Centero
                                                       February 14, 2014
     An Architecture for IPv6 over the TSCH mode of IEEE 802.15.4e
                   draft-ietf-6tisch-architecture-01
Abstract
   This document presents an architecture for an IPv6 Multi-Link subnet
   that is composed of a high speed powered backbone and a number of
   IEEE802.15.4e TSCH wireless networks attached and synchronized by
   Backbone Routers.  The TSCH schedule can be static or dynamic.
   6TiSCH defines mechanisms to establish and maintain the routing and
   scheduling operations in a centralized, distributed, or mixed
   fashion.  Backbone Routers perform proxy Neighbor Discovery
   operations over the backbone on behalf of the wireless devices, so
   they can share a same subnet and appear to be connected to the same
   backbone as classical devices
Requirements Language
   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in RFC
   2119 [RFC2119].
Status of this Memo
   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.
   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.
   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."
   This Internet-Draft will expire on August 16, 2014.
Copyright Notice

Thubert, Watteyne & AssiExpires August 16, 2014                 [Page 1]


Internet-Draft            6TiSCH-architecture              February 2014
   Copyright (c) 2014 IETF Trust and the persons identified as the
   document authors.  All rights reserved.
   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents (http://trustee.ietf.org/
   license-info) in effect on the date of publication of this document.
   Please review these documents carefully, as they describe your rights
   and restrictions with respect to this document.  Code Components
   extracted from this document must include Simplified BSD License text
   as described in Section 4.e of the Trust Legal Provisions and are
   provided without warranty as described in the Simplified BSD License.
Table of Contents
   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  2
   2.  Terminology  . . . . . . . . . . . . . . . . . . . . . . . . .  4
   3.  Applications and Goals . . . . . . . . . . . . . . . . . . . .  4
   4.  Overview and Scope . . . . . . . . . . . . . . . . . . . . . .  5
   5.  Communication Paradigms and Interaction Models . . . . . . . .  8
   6.  Forwarding Models  . . . . . . . . . . . . . . . . . . . . . .  9
     6.1.  Track Forwarding . . . . . . . . . . . . . . . . . . . . .  9
       6.1.1.  Transport Mode . . . . . . . . . . . . . . . . . . . .  9
       6.1.2.  Tunnel Mode  . . . . . . . . . . . . . . . . . . . . . 10
       6.1.3.  Tunnel Metadata  . . . . . . . . . . . . . . . . . . . 11
     6.2.  Fragment Forwarding  . . . . . . . . . . . . . . . . . . . 12
     6.3.  IPv6 Forwarding  . . . . . . . . . . . . . . . . . . . . . 13
   7.  TSCH and 6top  . . . . . . . . . . . . . . . . . . . . . . . . 13
     7.1.  6top . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
     7.2.  6top and RPL Objective Function operations . . . . . . . . 14
     7.3.  Network Synchronization  . . . . . . . . . . . . . . . . . 15
     7.4.  Slotframes and Priorities  . . . . . . . . . . . . . . . . 16
     7.5.  Packet Marking and Handling  . . . . . . . . . . . . . . . 16
     7.6.  Distributing the reservation of timeslots  . . . . . . . . 17
   8.  Schedule Management Mechanisms . . . . . . . . . . . . . . . . 18
     8.1.  Minimal Static Scheduling  . . . . . . . . . . . . . . . . 18
     8.2.  Neighbor-to-neighbor Scheduling  . . . . . . . . . . . . . 19
     8.3.  Remote Monitoring and Schedule Management  . . . . . . . . 19
     8.4.  Hop-by-hop Scheduling  . . . . . . . . . . . . . . . . . . 20
   9.  Centralized vs. Distributed Routing  . . . . . . . . . . . . . 20
   10. IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 21
   11. Security Considerations  . . . . . . . . . . . . . . . . . . . 21
   12. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 21
   13. References . . . . . . . . . . . . . . . . . . . . . . . . . . 21
     13.1.  Normative References  . . . . . . . . . . . . . . . . . . 21
     13.2.  Informative References  . . . . . . . . . . . . . . . . . 22
     13.3.  External Informative References . . . . . . . . . . . . . 23
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 24
1.  Introduction


Thubert, Watteyne & AssiExpires August 16, 2014                 [Page 2]


Internet-Draft            6TiSCH-architecture              February 2014
   The emergence of radio technology enabled a large variety of new
   types of devices to be interconnected, at a very low marginal cost
   compared to wire, at any range from Near Field to interplanetary
   distances, and in circumstances where wiring would be less than
   practical, for instance rotating devices.
   At the same time, a new breed of Time Sensitive Networks is being
   developed to enable traffic that is highly sensitive to jitter and
   quite sensitive to latency.  Such traffic is not limited to voice and
   video, but also includes command and control operations such as found
   in industrial automation or in-vehicle sensors and actuators.
   At IEEE802.1, the "Audio/Video Task Group", was renamed TSN for Time
   Sensitive Networking to address Deterministic Ethernet.  The
   IEEE802.15.4 Medium access Control (MAC) has evolved with
   IEEE802.15.4e that provides in particular the Timeslotted Channel
   Hopping (TSCH) mode for industrial-type applications.
   Though at a different time scale, both standards provide
   Deterministic capabilities to the point that a packet that pertains
   to a certain flow crosses the network from node to node following a
   very precise schedule, as a train that leaves intermediate stations
   at precise times along its path.  With TSCH, time is formatted into
   timeslots, and an individual timeslot is allocated to unicast or
   broadcast communication at the MAC level.  The time slotted operation
   reduces collisions, saves energy, and enables to more closely
   engineer the network for deterministic properties.  The channel
   hopping aspect is a simple and efficient technique to combat
   multipath fading and external interference (for example by WiFi
   emitters).
   This document presents an architecture for an IPv6 Multi-Link subnet
   that is composed of a high speed powered backbone and a number of
   IEEE802.15.4e TSCH wireless networks attached and synchronized by
   backbone routers.  Route Computation may be achieved in a centralized
   fashion by a Path Computation Element (PCE), in a distributed fashion
   using the Routing Protocol for Low Power and Lossy Networks (RPL), or





Thubert, Watteyne & AssiExpires August 16, 2014                 [Page 3]


Internet-Draft            6TiSCH-architecture              February 2014
   in a mixed mode.  The Backbone Routers perform proxy IPv6 neighbor
   Discovery (ND) operations over the backbone on behalf of the wireless
   devices, so they can share a same IPv6 subnet and appear to be
   connected to the same backbone as classical devices.  Timeslots and
   other device resources are managed by an abstract Network Management
   Entity (NME) that may cooperate with the PCE in order to minimize the
   interaction with and the load on the constrained device.
2.  Terminology
   Readers are expected to be familiar with all the terms and concepts
   that are discussed in "neighbor Discovery for IP version 6"
   [RFC4861],  "IPv6 over Low-Power Wireless Personal Area Networks
   (6LoWPANs): Overview, Assumptions, Problem Statement, and Goals"
   [RFC4919], neighbor Discovery Optimization for Low-power and Lossy
   Networks [RFC6775] and "Multi-link Subnet Support in IPv6" [I-D.ietf-
   ipv6-multilink-subnets].
   Readers may benefit from reading the "RPL: IPv6 Routing Protocol for
   Low-Power and Lossy Networks"  [RFC6550] specification; "Multi-Link
   Subnet Issues" [RFC4903]; "Mobility Support in IPv6"  [RFC6275];
   "neighbor Discovery Proxies (ND Proxy)"  [RFC4389]; "IPv6 Stateless
   Address Autoconfiguration" [RFC4862]; "FCFS SAVI: First-Come, First-
   Served Source Address Validation Improvement for Locally Assigned
   IPv6 Addresses" [RFC6620]; and "Optimistic Duplicate Address
   Detection" [RFC4429] prior to this specification for a clear
   understanding of the art in ND-proxying and binding.
   The draft uses terminology defined or referenced in [I-D.ietf-6tisch-
   terminology], [I-D.chakrabarti-nordmark-6man-efficient-nd], [I-D
   .roll-rpl-industrial-applicability], [RFC5191] and [RFC4080].
   The draft also conforms to the terms and models described  in
   [RFC3444] and [RFC5889] and uses the vocabulary and the concepts
   defined in [RFC4291] for the IPv6 Architecture.
3.  Applications and Goals
   The architecture derives from existing industrial standards for
   Process Control by its focus on Deterministic Networking, in
   particular with the use of the IEEE802.15.4e TSCH MAC [IEEE802154e]
   and the centralized PCE.  This approach leverages the TSCH MAC
   benefits for high reliability against interference, low-power
   consumption on deterministic traffic, and its Traffic Engineering
   capabilities.  Deterministic Networking applies in particular to open
   and closed control loops, as well as supervisory control flows and
   management.
   An incremental set of industrial requirements are addressed with the
   addition of an autonomic and distributed routing operation based on
   RPL. These use cases include plant setup and decommissioning, as well
   as monitoring of lots of lesser importance measurements such as

Thubert, Watteyne & AssiExpires August 16, 2014                 [Page 4]


Internet-Draft            6TiSCH-architecture              February 2014
   corrosion and events.  RPL also enables mobile use cases such as
   mobile workers and cranes.
   A Backbone Router is included in order to scale the factory plant
   subnet to address large deployments, with proxy ND and time
   synchronization over a high speed backbone.
   The architecture also applies to building automation that leverage
   RPL's storing mode to address multipath over a large number of hops,
   in-vehicle command and control that can be as demanding as industrial
   applications, commercial automation and asset Tracking with mobile
   scenarios, home automation and domotics which become more reliable
   and thus provide a better user experience, and resource management
   (energy, water, etc.).
4.  Overview and Scope
   The scope of the present work is a subnet that, in its basic
   configuration, is made of a IEEE802.15.4e Timeslotted Channel Hopping
   (TSCH) [I-D.ietf-6tisch-tsch] MAC Low Power Lossy Network (LLN).
            ---+-------- ............ ------------
               |      External Network       |
               |                          +-----+
            +-----+                       | NME |
            |     | LLN Border            |     |
            |     | router                +-----+
            +-----+
          o    o   o
   o     o   o     o
      o   o LLN   o    o     o
         o   o   o       o
                 o
   The LLN devices communicate over IPv6 [RFC2460] using the 6LoWPAN
   Header Compression (6LoWPAN HC) [RFC6282].  From the perspective of
   Layer 3, a single LLN interface (typically an IEEE802.15.4-compliant
   radio) may be seen as a collection of Links with different
   capabilities for unicast or multicast services.  An IPv6 subnet spans
   over multiple links, effectively forming a Multi-Link subnet.  Within
   that subnet, neighbor Devices are discovered with 6LoWPAN neighbor
   Discovery (6LoWPAN ND) [RFC6775].  RPL [RFC6550] enables routing
   within the LLN, typically within the Multi-Link subnet in the so
   called Route Over fashion.  RPL forms Destination Oriented Directed
   Acyclic Graphs (DODAGs) within Instances of the protocol, each
   Instance being associated with an Objective Function (OF) to form a



Thubert, Watteyne & AssiExpires August 16, 2014                 [Page 5]


Internet-Draft            6TiSCH-architecture              February 2014
   routing topology.  A particular LLN device, the LLN Border Router
   (LBR), acts as RPL root, 6LoWPAN HC terminator, and LLN Border Router
   (LBR) to the outside.  The LBR is usually powered.  More on RPL
   Instances can be found in RPL [RFC6550], sections "3.1.2. RPL
   Identifiers" and "3.1.3. Instances, DODAGs, and DODAG Versions".
   An extended configuration of the subnet comprises multiple LLNs.  The
   LLNs are interconnected and synchronized over a backbone, that can be
   wired or wireless.  The backbone can be a classical IPv6 network,
   with neighbor Discovery operating as defined in [RFC4861] and
   [RFC4862].  The backbone can also support Efficiency-aware IPv6
   neighbor Discovery Optimizations  [I-D.chakrabarti-nordmark-6man-
   efficient-nd] in mixed mode as described in [I-D.thubert-6lowpan-
   backbone-router].
   Security is often handled at layer 2 and Layer 4. Authentication
   during the join process can be handled by the Protocol for Carrying
   Authentication for Network access (PANA) [RFC5191].
   The LLN devices are time-synchronized at the MAC level.  The LBR that
   serves as time source is a RPL parent in a particular RPL instance
   that serves for time synchronization; this way, the time
   synchronization starts at the RPL root and follows the RPL DODAGs
   with no timing loop.
   In the extended configuration, the functionality of the LBR is
   enhanced to that of Backbone Router (BBR). A BBR is an LBR, but also
   an Energy Aware Default Router (NEAR) as defined in [I-D.chakrabarti-
   nordmark-6man-efficient-nd].  The BBR performs ND proxy operations
   between the registered devices and the classical ND devices that are
   located over the backbone.  6TiSCH BBRs synchronize with one another
   over the backbone, so as to ensure that the multiple LLNs that form
   the IPv6 subnet stay tightly synchronized.  If the Backbone is
   Deterministic (such as defined by the Time Sensitive Networking WG at
   IEEE), then the Backbone Router ensures that the end-to-end
   deterministic behavior is maintained between the LLN and the
   backbone.






Thubert, Watteyne & AssiExpires August 16, 2014                 [Page 6]


Internet-Draft            6TiSCH-architecture              February 2014
               ---+-------- ............ ------------
                  |      External Network       |
                  |                          +-----+
                  |             +-----+      | NME |
               +-----+          |  +-----+   |     |
               |     | Router   |  | PCE |   +-----+
               |     |          +--|     |
               +-----+             +-----+
                  |                   |
                  | Subnet Backbone   |
            +--------------------+------------------+
            |                    |                  |
         +-----+             +-----+             +-----+
         |     | Backbone    |     | Backbone    |     | Backbone
    o    |     | router      |     | router      |     | router
         +-----+             +-----+             +-----+
    o                  o                   o                 o   o
        o    o   o         o   o  o   o         o  o   o    o
   o             o        o  LLN      o      o         o      o
      o   o    o      o      o o     o  o   o    o    o     o
   The main architectural blocks are arranged as follows:
   +-----+-----+-----+-----+-------+-----+
   |PCEP |   CoAP    |PANA |6LoWPAN| RPL |
   | PCE |DTLS |     |     |   ND  |     |
   +-----+-----+-----+-----+-------+-----+-----+
   | TCP |       UDP       |    ICMP     |RSVP |
   +-----+-----+-----+-----+-------+-----+-----+
   |                 IPv6                      |
   +-------------------------------------------+
   |               6LoWPAN HC                  |
   +-------------------------------------------+
   |                   6top                    |
   +-------------------------------------------+
   |             IEEE802.15.4e   TSCH          |
   +-------------------------------------------+
   RPL is the routing protocol of choice for LLNs.  (TBD RPL) whether
   there is a need to define a 6TiSCH OF.
   (tbd NME) COMAN is working on network Management for LLN.  They are
   considering the Open Mobile Alliance (OMA) Lightweight M2M (LWM2M)
   Object system.  This standard includes DTLS, CoAP (core plus Block
   and Observe patterns), SenML and CoAP Resource Directory.
   (tbd PCE) need to work with PCE WG to define flows to PCE, and define
   how to accommodate PCE routes and reservation.  Will probably look a
   lot like GMPLS.

Thubert, Watteyne & AssiExpires August 16, 2014                 [Page 7]


Internet-Draft            6TiSCH-architecture              February 2014
   (tbd PANA) There is a debate whether PANA (layer 3) or IEEE802.1x
   (layer 2) should be used in the join process.  There is also a debate
   whether the node should be able to send any unprotected packet on the
   medium.  Regardless, the security model must ensure that, prior to a
   join process, packets from a untrusted device must be controlled in
   volume and in reachability.
   (tbd Backbone Router) need to work with 6MAN to define ND proxy.
   Also need BBR sync sync between deterministic Ethernet and 6TiSCH
   LLNs.
   IEEE802.1TSN: external, maintain consistency.  See also AVnu.
   IEEE802.15.4: external, (tbd need updates?).
   ISA100.20 Common Network Management: external, maintain consistency.
   The 6TiSCH Operation sublayer (6top) [I-D.wang-6tisch-6top-sublayer]
   is an Logical Link Control (LLC) or a portion thereof that provides
   the abstraction of an IP link over a TSCH MAC.
5.  Communication Paradigms and Interaction Models
   [I-D.ietf-6tisch-terminology] defines the terms of Communication
   Paradigms and Interaction Models, which can be placed in parallel to
   the  Information Models and Data Models that are defined in
   [RFC3444].
   A Communication Paradigms would be an abstract view of a protocol
   exchange, and would come with an Information Model for the
   information that is being exchanged.  In contrast, an Interaction
   Models would be more refined and could point on standard operation
   such as a Representational state transfer (REST) "GET" operation and
   would match a Data Model for the data that is provided over the
   protocol exchange.
   [I-D.roll-rpl-industrial-applicability] section 2.1.3. and next
   discusses appplication-layer paradigms, such as Source-sink (SS) that
   is a Multipeer to Multipeer (MP2MP) model that is primarily used for
   alarms and alerts, Publish-subscribe (PS, or pub/sub) that is
   typically used for sensor data, as well as Peer-to-peer (P2P) and
   Peer-to-multipeer (P2MP) communications.  Additional considerations
   on Duocast and its N-cast generalization are also provided.  Those
   paradigms are frequently used in industrial automation, which is a
   major use case for IEEE802.15.4e TSCH wireless networks with
   [ISA100.11a] and [HART].


Thubert, Watteyne & AssiExpires August 16, 2014                 [Page 8]


Internet-Draft            6TiSCH-architecture              February 2014
   This specification focuses on Communication Paradigms and Interaction
   Models for packet forwarding and TSCH resources (cells) management.
   L ink-layer and Network-layer Packet forwarding interactions are
   discussed in Section 6, whereas Link-layer (one-hop), Network-layer
   (multithop along a track), and Application-layer (remote control)
   management mechanisms for the TSCH schedule are discussed in Section
   8.
6.  Forwarding Models
   6TiSCH supports three different forwarding model, G-MPLS Track
   Forwarding (TF), 6LoWPAN Fragment Forwarding (FF) and IPv6 Forwarding
   (6F).
6.1.  Track Forwarding
   Track Forwarding is the simplest and fastest.  A set of input cells
   are uniquely bound to a set of output cells, representing a
   forwarding state that can be used regardless of the upper layer
   protocol.  This model can effectively be seen as a G-MPLS operation
   in that the information used to switch is not an explicit label, but
   rather related to other properties of the way the packet was
   received, a particular cell in the case of 6TiSCH.  As a result, as
   long as the TSCH MAC (and Layer 2 security) accepts a frame, that
   frame can be switched regardless of the protocol, whether this is an
   IPv6 packet, a 6LoWPAN fragment, or a frame from an alternate
   protocol such as WirelessHART of ISA100.11a.
   A Track is defined end-to-end as a succession of timeslots.  A
   timeslot belongs to at most one Track.  For a given iteration of a
   slotframe, the timeslot is associated uniquely with a cell, which
   indicates the channel at which the timeslot operates for that
   iteration.
   A data frame that is forwarded along a Track has a destination MAC
   address set to broadcast or a multicast address depending on MAC
   support.  This way, the MAC layer in the intermediate nodes accepts
   the incoming frame and 6top switches it without incurring a change in
   the MAC header.  In the case of IEEE802.15.4e, this means effectively
   broadcast, so that along the Track the short address for the
   destination is set to 0xFFFF.
   Conversely, a frame that is received along a Track with a destination
   MAC address set to this node is extracted from the Track stream and
   delivered to the upper layer.  A frame with an unrecognized MAC
   address is ignored at the MAC layer and thus is not received at the
   6top sublayer.
   There are 2 modes for a Track, transport mode and tunnel mode.
6.1.1.  Transport Mode

Thubert, Watteyne & AssiExpires August 16, 2014                 [Page 9]


Internet-Draft            6TiSCH-architecture              February 2014
   In transport mode, the PDU is associated flow information that refers
   uniquely to the Track, so the 6top sublayer can place the frame in
   the appropriate timeslot without ambiguity.  In the case of IPv6
   traffic, flow identification is transported in the Flow Label of the
   IPv6 header.  Associated with the source IPv6 address, the flow label
   forms a globally unique identifier for that particular Track that is
   validated at egress before restoring the destination MAC address
   (dmac) and punting to the upper layer.
                       |                                    ^
   +--------------+    |                                    |
   |     IPv6     |    |                                    |
   +--------------+    |                                    |
   |  6LoWPAN HC  |    |                                    |
   +--------------+  ingress                              egress
   |     6top     |   sets     +----+          +----+     restores
   +--------------+  dmac to   |    |          |    |     dmac to
   |   TSCH MAC   |   brdcst   |    |          |    |      self
   +--------------+    |       |    |          |    |       |
   |   LLN PHY    |    +-------+    +--...-----+    +-------+
   +--------------+
6.1.2.  Tunnel Mode
   In tunnel mode, the frames originate from an arbitrary protocol over
   a compatible MAC that may or may not be synchronized with the 6TiSCH
   network.  An example of this would be a router with a dual radio that
   is capable of receiving and sending WirelessHART or ISA100.11a frames
   with the second radio, by presenting itself as an access Point or a
   Backbone Router, respectively.
   In that mode, some entity (e.g.  PCE) can coordinate with a
   WirelessHART Network Manager or an ISA100.11a System Manager to
   specify the flows that are to be transported transparently over the
   Track.






Thubert, Watteyne & AssiExpires August 16, 2014                [Page 10]


Internet-Draft            6TiSCH-architecture              February 2014
   +--------------+
   |     IPv6     |
   +--------------+
   |  6LoWPAN HC  |
   +--------------+             set            restore
   |     6top     |            +dmac+          +dmac+
   +--------------+            |    |          |    |
   |   TSCH MAC   |            |    |          |    |
   +--------------+            |    |          |    |
   |   LLN PHY    |    +-------+    +--...-----+    +-------+
   +--------------+    |   ingress                 egress   |
                       |                                    |
   +--------------+    |                                    |
   |   LLN PHY    |    |                                    |
   +--------------+    |                                    |
   |   TSCH MAC   |    |                                    |
   +--------------+    |                                    |
   |ISA100/WiHART |    |                                    v
   +--------------+
   In that case, the flow information that identifies the Track is
   uniquely derived from the information at the receiving end, for
   instance the incoming timeslots, or an ISA100.11a ContractId.  At the
   ingress 6TiSCH router, the packet destination is recognized as self
   but the flow information indicates that the frame must be tunnelled
   over a particular 6top Track so the packet is not punted to upper
   layer.  Instead, it is passed to the 6top sublayer for switching.
   The 6top sublayer in the ingress router overrides the destination MAC
   to broadcast and forwards.
   At the egress 6top router, the reverse operation occurs.  Based on
   metadata associated to the Track, the frame is passed to the
   appropriate link layer with the destination MAC restored.
6.1.3.  Tunnel Metadata
   Metadata coming with the Track configuration is expected to provide
   the destination MAC address of the egress endpoint as well as the
   tunnel mode and specific data depending on the mode, for instance a
   service access point for frame delivery at egress.  If the tunnel
   egress point does not have a MAC address that matches the
   configuration, the Track installation fails.
   In transport mode, if the final layer 3 destination is the tunnel
   termination, then it is possible that the IPv6 address of the
   destination is compressed at the 6LoWPAN sublayer based on the MAC
   address.  It is thus mandatory at the ingress point to validate that
   the MAC address that was used at the 6LoWPAN sublayer for compression
   matches that of the tunnel egress point.  For that reason, the node
   that injects a packet on a Track checks that the destination is
   effectively that of the tunnel egress point before it overwrites it
   to broadcast.  The 6top sublayer at the tunnel egress point reverts
Thubert, Watteyne & AssiExpires August 16, 2014                [Page 11]


Internet-Draft            6TiSCH-architecture              February 2014
   that operation to the MAC address obtained from the tunnel metadata.
6.2.  Fragment Forwarding
   Considering that 6LoWPAN packets can be as large as 1280 bytes (the
   IPv6 MTU), and that the non-storing mode of RPL implies Source
   Routing that requires space for routing headers, and that a
   IEEE802.15.4 frame with security may carry in the order of 80 bytes
   of effective payload, an IPv6 packet might be fragmented into more
   than 16 fragments at the 6LoWPAN sublayer.
   This level of fragmentation is much higher than that traditionally
   experienced over the Internet with IPv4 fragments, where
   fragmentation is already known as harmful.
   In the case to a multihop route within a 6TiSCH network, Hop-by-Hop
   recomposition occurs at each hop in order to reform the packet and
   route it.  This creates additional latency and forces intermediate
   nodes to store a portion of a packet for an undetermined time, thus
   impacting critical resources such as memory and battery.
   [I-D.thubert-roll-forwarding-frags] describes a mechanism whereby the
   datagram tag in the 6LoWPAN Fragment is used as a label for switching
   at the 6LoWPAN sublayer.  The draft allows for a degree of flow
   control base on an Explicit Congestion Notification, as well as end-
   to-end individual fragment recovery.
                       |                                    ^
   +--------------+    |                                    |
   |     IPv6     |    |       +----+          +----+       |
   +--------------+    |       |    |          |    |       |
   |  6LoWPAN HC  |    |       learn           learn        |
   +--------------+    |       |    |          |    |       |
   |     6top     |    |       |    |          |    |       |
   +--------------+    |       |    |          |    |       |
   |   TSCH MAC   |    |       |    |          |    |       |
   +--------------+    |       |    |          |    |       |
   |   LLN PHY    |    +-------+    +--...-----+    +-------+
   +--------------+
   In that model, the first fragment is routed based on the IPv6 header
   that is present in that fragment.  The 6LoWPAN sublayer learns the
   next hop selection, generates a new datagram tag for transmission to
   the next hop, and stores that information indexed by the incoming MAC
   address and datagram tag.  The next fragments are then switched based
   on that stored state.



Thubert, Watteyne & AssiExpires August 16, 2014                [Page 12]


Internet-Draft            6TiSCH-architecture              February 2014
                       |                                    ^
   +--------------+    |                                    |
   |     IPv6     |    |                                    |
   +--------------+    |                                    |
   |  6LoWPAN HC  |    |       replay          replay       |
   +--------------+    |       |    |          |    |       |
   |     6top     |    |       |    |          |    |       |
   +--------------+    |       |    |          |    |       |
   |   TSCH MAC   |    |       |    |          |    |       |
   +--------------+    |       |    |          |    |       |
   |   LLN PHY    |    +-------+    +--...-----+    +-------+
   +--------------+
   A bitmap and an ECN echo in the end-to-end acknowledgement enable the
   source to resend the missing fragments selectively.  The first
   fragment may be resent to carve a new path in case of a path failure.
   The ECN echo set indicates that the number of outstanding fragments
   should be reduced.
6.3.  IPv6 Forwarding
   As the packets are routed at layer 3, traditional QoS and RED
   operations are expected to prioritize flows with differentiated
   services.  A new class of service for Deterministic Forwarding is
   being defined to that effect in [I-D.svshah-tsvwg-lln-diffserv-
   recommendations].
                       |                                    ^
   +--------------+    |                                    |
   |     IPv6     |    |       +-QoS+          +-QoS+       |
   +--------------+    |       |    |          |    |       |
   |  6LoWPAN HC  |    |       |    |          |    |       |
   +--------------+    |       |    |          |    |       |
   |     6top     |    |       |    |          |    |       |
   +--------------+    |       |    |          |    |       |
   |   TSCH MAC   |    |       |    |          |    |       |
   +--------------+    |       |    |          |    |       |
   |   LLN PHY    |    +-------+    +--...-----+    +-------+
   +--------------+
7.  TSCH and 6top
7.1.  6top



Thubert, Watteyne & AssiExpires August 16, 2014                [Page 13]


Internet-Draft            6TiSCH-architecture              February 2014
   6top is a logical link control sitting between the IP layer and the
   TSCH MAC layer, which provides the link abstraction that is required
   for IP operations.  The 6top operations are specified in [I-D.wang-
   6tisch-6top-sublayer].  In particular, 6top provides a management
   interface that enables an external management entity to schedule
   cells and Slotframes, and allows the addition of complementary
   functionality, for instance to support a dynamic schedule management
   based on observed resource usage as discussed in section Section 8.2.
   The 6top data model and management interfaces are further discussed
   in Section 8.3.
   If the scheduling entity explicitly specifies the slotOffset/
   channelOffset of the cells to be added/deleted, those cells are
   marked as "hard".  6top cannot move hard cells in the TSCH schedule.
   Hard cells are for example used by a central PCE.
   6top contains a monitoring process which monitors the performance of
   cells, and can move a cell in the TSCH schedule when it performs bad.
   This is only applicable to cells which are marked as "soft".  To
   reserve a soft cell, the higher layer does not indicate the exact
   slotOffset/channelOffset of the cell to add, but rather the resulting
   bandwidth and QoS requirements.  When the monitoring process triggers
   a cell reallocation, the two neighbor motes communicating over this
   cell negotiate its new position in the TSCH schedule.
7.2.  6top and RPL Objective Function operations
   An implementation of a RPL [RFC 6550] Objective Function (OF), such
   as the RPL Objective Function Zero (OF0)  [RFC 6552] that is used in
   the Minimal 6TiSCH Configuration  [I-D.ietf-6tisch-minimal] to
   support RPL over a static schedule, may leverage, for its internal
   computation, the information maintained by 6top.
   In particular, 6top creates and maintains an abstract neighbor table.
   A neighbor table entry contains a set of statistics with respect to
   that specific neighbor including the ASN when the last packet has
   been received from that neighbor, a set of cell quality metrics
   (RSSI, LQI), the number of packets sent to the neighbor or the number
   of packets received from it.  This information can be obtained
   through 6top management APIs as detailed in the 6top sublayer
   specification  [I-D.wang-6tisch-6top-sublayer] and used to compute a
   Rank Increment that will determine the selection of the preferred
   parent.
   6top provides statistics about the underlying layer so the OF can be
   tuned to the nature of the TSCH MAC layer.  6top also enables the RPL
   OF to influence the MAC behaviour, for instance by configuring the
   periodicity of EBs.  By augmenting the EB periodicity, it is possible
   to change the network dynamics so as to improve the support of mobile
   devices.

Thubert, Watteyne & AssiExpires August 16, 2014                [Page 14]


Internet-Draft            6TiSCH-architecture              February 2014
   Some RPL control messages, such as the DODAG Information Object (DIO)
   are broadcast to all neighbor nodes.  The broadcast channel
   requirement is addressed by 6top by configuring TSCH to provide such
   a channel, as opposed to, for instance, carrying DIO messages in
   Enhance Beacons.
   In the TSCH schedule, each cell has the LinkType attribute.  Setting
   the LinkType to ADVERTISING indicates that the cell MAY be used to
   send an Enhanced Beacon.  When a node forms its Enhanced Beacon, the
   cell, with LinkType=ADVERTISING, SHOULD be included in the
   FrameAndLinkIE, and its LinkOption field SHOULD be set to the
   combination of "Receive" and "Timekeeping".  The receiver of the
   Enhanced Beacon MAY be listening at the cell to get the Enhanced
   Beacon ([IEEE802154e]).  6top takes this way to establish broadcast
   channel, which not only allows TSCH to broadcast Enhanced Beacons,
   but also allows an upper layer like RPL.
   To support DIO and DAO broadcasts, 6top uses the payload of a Data
   Packet to carry the DIO or DAO. The message is inserted into the
   queue associated with the cells which LinkType is set to ADVERTISING.
   Then, taking advantage of the broadcast cell feature established with
   FrameAndLinkIE (as described above), the data packet with DIO or DAO
   in the payload can be received by neighbors, which enforces the
   maintenance of DODAG.
   A LinkOption combining "Receive" and "Timekeeping" bits indicates to
   the receivers of the Enhanced Beacon that the cell MUST be used as a
   broadcast cell.  The frequency of sending Enhanced Beacons or other
   broadcast messages by the upper layer is determined by the timers
   associated with the messages.  For example, the transmission of
   Enhance Beacons is triggered by a timer in 6top; transmission of a
   DIO message is triggered by the trickle timer of RPL.
7.3.  Network Synchronization
   Nodes in a TSCH network must be time synchronized.  A node keeps
   synchronized to its time source neighbor through a combination of
   frame-based and acknowledgement-based synchronization.  In order to
   maximize battery life and network throughput, it is advisable that
   RPL ICMP discovery and maintenance traffic (governed by the trickle
   timer) be somehow coordinated with the transmission of time
   synchronization packets (especially with enhanced beacons).  This
   could be achieved through an interaction of the 6top sublayer and the
   RPL objective Function, or could be controlled by a management
   entity.



Thubert, Watteyne & AssiExpires August 16, 2014                [Page 15]


Internet-Draft            6TiSCH-architecture              February 2014
   Time distribution requires a loop-less structure.  Nodes taken in a
   synchronization loop will rapidly desynchronize from the network and
   become isolated.  It is expected that a RPL DAG with a dedicated
   global Instance is  deployed for the purpose of time synchronization.
   That Instance is referred to as the Time Synchronization Global
   Instance (TSGI).  The TSGI can be operated in either of the 3 modes
   that are detailed in RPL [RFC6550]  section "3.1.3. Instances,
   DODAGs, and DODAG Versions".  Multiple uncoordinated DODAGs with
   independent roots may be used if all the roots share a common time
   source such as the Global Positioning System (GPS). In the absence of
   a common time source, the TSGI should form a single DODAG with a
   virtual root.  A backbone network is then used to synchronize and
   coordinate RPL operations between the backbone routers that act as
   sinks for the LLN.
   A node that has not joined the TSGI advertises a MAC level Join
   Priority of 0xFF to notify its neighbors that is is not capable of
   serving as time parent.  A node that has joined the TSGI advertises a
   MAC level Join Priority set to its DAGRank() in that Instance, where
   DAGRank() is the operation specified in [RFC6550], section "3.5.1.
   Rank Comparison".
   A root is configured or obtains by some external means the knowledge
   of the RPLInstanceID for the TSGI. The root advertises its DagRank in
   the TSGI, that MUST be less than 0xFF, as its Join Priority (JP) in
   its IEEE802.15.4e Extended Beacons (EB). We'll note that the JP is
   now specified between 0 and 0x3F leaving 2 bit sin the octet unused
   in the IEEE802.15.4e specification.  After consultation with IEEE
   authors, it was asserted that 6TiSCH can make a full use of the octet
   to carry an integer value up to 0xFF.
   A node that reads a Join Priority of less than 0xFF should join the
   neighbor with the lesser Join Priority and use it as time parent.  If
   the node is configured to serve as time parent, then the node should
   join the TSGI, obtain a Rank in that Instance and start advertising
   its own DagRank in the TSGI as its Join Priority in its EBs.
7.4.  Slotframes and Priorities
   6top uses priority queues to manage concurrent data flows of
   different priorities.  When a packet is received from an higher layer
   for transmission, the I-MUX module of 6top inserts that packet in the
   outgoing queue which matches the packet best (DSCP can therefore be
   used). At each scheduled transmit slot, the MUX module looks for the
   frame in all the outgoing queues that best matches the cells.  If a
   frame is found, it is given to TSCH for transmission.
7.5.  Packet Marking and Handling


Thubert, Watteyne & AssiExpires August 16, 2014                [Page 16]


Internet-Draft            6TiSCH-architecture              February 2014
   reservation Deterministic flow allocation (hard reservation of
   timeslots) eg centralized RSVP? metrics?  Hop-by-hop interaction with
   6top.  Lazy reservation (use shared slots to transport extra burst
   and then dynamically (de)allocate) Classical QoS (dynamic based on
   observation)
7.6.  Distributing the reservation of timeslots
   6TiSCH expects a high degree of scalability together with a
   distributed routing functionality based on the RPL routing protocol.
   To achieve this goal, the spectrum must be allocated in a way that
   allows for spatial reuse between zones that will not interfere with
   one another.  In a large and spatially distributed network, a 6TiSCH
   node is often in a good position to determine usage of spectrum in
   its vicinity.
   Use cases for distributed routing are often associated with a
   statistical distribution of best-effort traffic with variable needs
   for bandwidth on each individual link.  With 6TiSCH, the link
   abstraction is implemented as a bundle of cells; the size of a bundle
   is optimal when both the energy wasted idle listening and the packet
   drops due to congestion loss are minimized.  This can be maintained
   if the number of cells in a bundle is adapted dynamically, and with
   enough reactivity, to match the variations of best-effort traffic.
   In turn, the agility to fulfill the needs for additional cells
   improves when the number of interactions with other devices and the
   protocol latencies are minimized.
   6TiSCH limits that interaction to RPL parents that will only
   negotiate with other RPL parents, and performs that negotiation by
   groups of cells as opposed to individual cells.  The 6TiSCH
   architecture allows RPL parents to adjust dynamically, and
   independently from the PCE, the amount of bandwidth that is used to
   communicate between themselves and their children, in both
   directions; to that effect, an allocation mechanism enables a RPL
   parent to obtain the exclusive use of a portion of an abstract
   channel usage/distribution (CUD) matrix of timeslots within its
   interference domain.
   The 6TiSCH architecture introduces the concept of chunks [I-D.ietf-
   6tisch-terminology]) to operate such spectrum distribution for a
   whole group of cells at a time.  The CUD matrix is formatted into a
   set of chunks, each of them identified uniquely by a chunk-ID. The
   knowledge of this formatting is shared between all the nodes in a
   6TiSCH network.  6TiSCH also defines the process of chunk ownership
   appropriation whereby a RPL parent discovers a chunk that is not used
   in its interference domain (e.g lack of energy detected in reference
   cells in that chunk); then claims the chunk, and then defends it in
   case another RPL parent would attempt to appropriate it while it is
   in use.  The chunks is the basic unit of ownership that is used in
   that process.

Thubert, Watteyne & AssiExpires August 16, 2014                [Page 17]


Internet-Draft            6TiSCH-architecture              February 2014

                +-----+-----+-----+-----+-----+-----+-----+     +-----+
   chan.Off. 0  |chnkA|chnkP|chnk7|chnkO|chnk2|chnkK|chnk1| ... |chnkZ|
                +-----+-----+-----+-----+-----+-----+-----+     +-----+
   chan.Off. 1  |chnkB|chnkQ|chnkA|chnkP|chnk3|chnkL|chnk2| ... |chnk1|
                +-----+-----+-----+-----+-----+-----+-----+     +-----+
                  ...
                +-----+-----+-----+-----+-----+-----+-----+     +-----+
   chan.Off. 15 |chnkO|chnk6|chnkN|chnk1|chnkJ|chnkZ|chnkI| ... |chnkG|
                +-----+-----+-----+-----+-----+-----+-----+     +-----+
                   0     1     2     3     4     5     6          M

   As a result of the process of chunk ownership appropriation, the RPL
   parent has exclusive authority to decide which cell in the
   appropriated chunk can be used by which node in its interference
   domain.  In other words, it is implicitly delegated the right to
   manage the portion of the slotframe that is represented by the chunk.
   The RPL parent may thus orchestrate which transmissions occur in any
   of the cells in the chunk, by allocating cells from the chunk to any
   form of communication (unicast, multicast) in any direction between
   itself and its children.  Initially, those cells are added to the
   heap of free cells, then dynamically placed into existing bundles, in
   new bundles, or allocated opportunistically for one transmission.
   The appropriation of a chunk can also be requested explicitly by the
   PCE to any node.  In that case, the node still may need to perform
   the appropriation process to validate that no other node has claimed
   that chunk already.  After a successful appropriation, the PCE owns
   the cells in that chunk, and may use them as hard cells to set up
   tracks.
8.  Schedule Management Mechanisms
   6TiSCH uses 4 paradigms to manage the TSCH schedule of the LLN nodes:
   Static Scheduling, neighbor-to-neighbor Scheduling, remote monitoring
   and scheduling management, and Hop-by-hop scheduling.  Multiple
   mechanisms are defined that implement the associated Interaction
   Models, and can be combined and used in the same LLN.  Which
   mechanism(s) to use depends on application requirements.
8.1.  Minimal Static Scheduling
   In the simplest instantiation of a 6TiSCH network, a common fixed
   schedule may be shared by all nodes in the network.  Cells are
   shared, and nodes contend for slot access in a slotted aloha manner.


Thubert, Watteyne & AssiExpires August 16, 2014                [Page 18]


Internet-Draft            6TiSCH-architecture              February 2014
   A static TSCH schedule can be used to bootstrap a network, as an
   initial phase during implementation, or as a fall-back mechanism in
   case of network malfunction.  This scheduled can be preconfigured or
   learnt by a node when joining the network.  Regardless, the schedule
   remains unchanged after the node has joined a network.  The Routing
   Protocol for LLNs (RPL) is used on the resulting network.  This
   "minimal" scheduling mechanism that implements this paradigm is
   detailed in [I-D.ietf-6tisch-minimal].
8.2.  Neighbor-to-neighbor Scheduling
   In the simplest instantiation of a 6TiSCH network described in
   Section 8.1, nodes may expect a packet at any cell in the schedule
   and will waste energy idle listening.  In a more complex
   instantiation of a 6TiSCH network, a matching portion of the schedule
   is established between peers to reflect the observed amount of
   transmissions between those nodes.  The aggregation of the cells
   between a node and a peer forms a bundle that the 6top layer uses to
   implement the abstraction of a link for IP. The bandwidth on that
   link is proportional to the number of cells in the bundle.
   If the size of a bundle is configured to fit an average amount of
   bandwidth, peak emissions will be destroyed.  If the size is
   configured to allow for peak emissions, energy is be wasted idle
   listening.
   In the most efficient instantiation of a 6TiSCH network, the size of
   the bundles that implement the links may be changed dynamically in
   order to adapt to the need of end-to-end flows routed by RPL.  An
   optional On-The-Fly (OTF) component may be used to monitor bandwidth
   usage and perform requests for dynamic allocation by the 6top
   sublayer.  The OTF component is not part of the 6top sublayer.  It
   may be collocated on the same device or may be partially or fully
   offloaded to an external system.
   The 6top sublayer  [I-D.wang-6tisch-6top-sublayer] defines a protocol
   for neighbor nodes to reserve soft cells to one another.  Because
   this reservation is done without global knowledge of the schedule of
   nodes in the LLN, scheduling collisions are possible.  6top defines a
   monitoring process which continuously tracks the packet delivery
   ratio of soft cells.  It uses these statistics to trigger the
   relocation of a soft cell in the schedule, using a negotiation
   protocol between the neighbors nodes communicating over that cell.
   Monitoring and relocation is done in the 6top layer.  For the upper
   layer, the connection between two neighbor nodes appears as an number
   of cells.  Depending on traffic requirements, the upper layer can
   request 6top to add or delete a number of cells scheduled to a
   particular neighbor, without being responsible for choosing the exact
   slotOffset/channelOffset of those cells.
8.3.  Remote Monitoring and Schedule Management
Thubert, Watteyne & AssiExpires August 16, 2014                [Page 19]


Internet-Draft            6TiSCH-architecture              February 2014
   The 6top interface document [I-D.wang-6tisch-6top-interface]
   specifies the generic data model that can be used to monitor and
   manage resources at the 6top sublayer.  Abstract methods are
   suggested for use by a management entity in the device.  The data
   model also enables remote control operations on the 6top sublayer.
   Being able to interact with the 6top sublayer of a node multiple hops
   away can be used for monitoring, scheduling, or a combination of
   both.  The architecture supports variations on the deployment model,
   and focuses on the flows rather than whether there is a proxy or a
   translational operation on the way.
   [I-D.sudhaakar-6tisch-coap] defines an mapping of 6top's set of
   commands described in [I-D.wang-6tisch-6top-interface] to CoAP
   resources.  This allows an entity to interact with the 6top layer of
   a node that is multiple hops away in a RESTful fashion.
   [I-D.sudhaakar-6tisch-coap] defines a basic set CoAP resources and
   associated RESTful access methods (GET/PUT/POST/DELETE). The payload
   (body) of the CoAP messages is encoded using the CBOR format.  The
   draft also defines the concept of "profiles" to allow for future or
   specific extensions, as well as a mechanism for a CoAP client to
   discover the profiles installed on a node.
   The entity issuing the CoAP requests can be a central scheduling
   entity (e.g.  a PCE), a node multiple hops away with the authority to
   modify the TSCH schedule (e.g.  the head of a local cluster), or a
   external device monitoring the overall state of the network (e.g.
   NME). The architecture allows for different types of interactions
   between this CoAP client and a node in the network:
8.4.  Hop-by-hop Scheduling
   A node can reserve a track to a destination node multiple hops away
   by installing soft cells at each intermediate node.  This forms a
   track of soft cells.  It is the responsibility of the 6top sublayer
   of each node on the track to monitor these soft cells and trigger
   relocation when needed.
   This hop-by-hop reservation mechanism is similar to [RFC2119] and
   [RFC5974].  The protocol for a node to trigger hop-by-hop scheduling
   is not yet defined.
9.  Centralized vs.  Distributed Routing
   6TiSCH supports a mixed model of centralized routes and distributed
   routes.  Centralized routes can for example computed by a entity such
   as a PCE. Distributed routes are computed by the RPL routing
   protocol.

Thubert, Watteyne & AssiExpires August 16, 2014                [Page 20]


Internet-Draft            6TiSCH-architecture              February 2014
   Both may inject routes in the Routing Tables of the 6TiSCH routers.
   In either case, each route is associated with a topology that is
   indexed by an RPLInstanceID, as defined in RPL [RFC6550].  RPL and
   PCE rely on shared sources to define Global and Local RPLInstanceIDs.
   It is possible for centralized and distributed routing to share a
   same topology.  In this case, centralized routes have precedence over
   distributed routes in case of conflict.
   Inside the 6TiSCH domain, the flow label is used to indicate the
   topology that must be used for routing.  The associated Routing
   Tables are discussed in [I-D.thubert-roll-flow-label].
10.  IANA Considerations
   This specification does not require IANA action.
11.  Security Considerations
   This specification is not found to introduce new security threat.
12.  Acknowledgements
13.  References
13.1.  Normative References
   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.
   [RFC2460]  Deering, S.E. and R.M. Hinden, "Internet Protocol, Version
              6 (IPv6) Specification", RFC 2460, December 1998.
   [RFC3444]  Pras, A. and J. Schoenwaelder, "On the Difference between
              Information Models and Data Models", RFC 3444, January
              2003.
   [RFC4080]  Hancock, R., Karagiannis, G., Loughney, J. and S. Van den
              Bosch, "Next Steps in Signaling (NSIS): Framework", RFC
              4080, June 2005.
   [RFC4291]  Hinden, R. and S. Deering, "IP Version 6 Addressing
              Architecture", RFC 4291, February 2006.
   [RFC4861]  Narten, T., Nordmark, E., Simpson, W. and H. Soliman,
              "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
              September 2007.
   [RFC4862]  Thomson, S., Narten, T. and T. Jinmei, "IPv6 Stateless
              Address Autoconfiguration", RFC 4862, September 2007.

Thubert, Watteyne & AssiExpires August 16, 2014                [Page 21]


Internet-Draft            6TiSCH-architecture              February 2014
   [RFC5191]  Forsberg, D., Ohba, Y., Patil, B., Tschofenig, H. and A.
              Yegin, "Protocol for Carrying Authentication for Network
              Access (PANA)", RFC 5191, May 2008.
   [RFC5889]  Baccelli, E. and M. Townsley, "IP Addressing Model in Ad
              Hoc Networks", RFC 5889, September 2010.
   [RFC5974]  Manner, J., Karagiannis, G. and A. McDonald, "NSIS
              Signaling Layer Protocol (NSLP) for Quality-of-Service
              Signaling", RFC 5974, October 2010.
   [RFC6282]  Hui, J. and P. Thubert, "Compression Format for IPv6
              Datagrams over IEEE 802.15.4-Based Networks", RFC 6282,
              September 2011.
   [RFC6550]  Winter, T., Thubert, P., Brandt, A., Hui, J., Kelsey, R.,
              Levis, P., Pister, K., Struik, R., Vasseur, JP. and R.
              Alexander, "RPL: IPv6 Routing Protocol for Low-Power and
              Lossy Networks", RFC 6550, March 2012.
   [RFC6552]  Thubert, P., "Objective Function Zero for the Routing
              Protocol for Low-Power and Lossy Networks (RPL)", RFC
              6552, March 2012.
   [RFC6775]  Shelby, Z., Chakrabarti, S., Nordmark, E. and C. Bormann,
              "Neighbor Discovery Optimization for IPv6 over Low-Power
              Wireless Personal Area Networks (6LoWPANs)", RFC 6775,
              November 2012.
13.2.  Informative References
   [I-D.chakrabarti-nordmark-6man-efficient-nd]
              Chakrabarti, S., Nordmark, E., Thubert, P. and M.
              Wasserman, "Wired and Wireless IPv6 Neighbor Discovery
              Optimizations", Internet-Draft draft-chakrabarti-nordmark-
              6man-efficient-nd-04, October 2013.
   [I-D.ietf-6tisch-minimal]
              Vilajosana, X. and K. Pister, "Minimal 6TiSCH
              Configuration", Internet-Draft draft-ietf-6tisch-
              minimal-00, November 2013.
   [I-D.ietf-6tisch-terminology]
              Palattella, M., Thubert, P., Watteyne, T. and Q. Wang,
              "Terminology in IPv6 over the TSCH mode of IEEE
              802.15.4e", Internet-Draft draft-ietf-6tisch-
              terminology-00, November 2013.
   [I-D.ietf-6tisch-tsch]
              Watteyne, T., Palattella, M. and L. Grieco, "Using
              IEEE802.15.4e TSCH in an LLN context: Overview, Problem
              Statement and Goals", Internet-Draft draft-ietf-6tisch-
              tsch-00, November 2013.
Thubert, Watteyne & AssiExpires August 16, 2014                [Page 22]


Internet-Draft            6TiSCH-architecture              February 2014
   [I-D.ietf-roll-rpl-industrial-applicability]
              Phinney, T., Thubert, P. and R. Assimiti, "RPL
              applicability in industrial networks", Internet-Draft
              draft-ietf-roll-rpl-industrial-applicability-02, October
              2013.
   [I-D.ohba-6tisch-security]
              Chasko, S., Das, S., Lopez, R., Ohba, Y., Thubert, P. and
              A. Yegin, "Security Framework and Key Management Protocol
              Requirements for 6TiSCH", Internet-Draft draft-ohba-
              6tisch-security-00, October 2013.
   [I-D.sudhaakar-6tisch-coap]
              Sudhaakar, R. and P. Zand, "6TiSCH Data Model for CoAP",
              Internet-Draft draft-sudhaakar-6tisch-coap-00, October
              2013.
   [I-D.svshah-tsvwg-lln-diffserv-recommendations]
              Shah, S. and P. Thubert, "Differentiated Service Class
              Recommendations for LLN Traffic", Internet-Draft draft-
              svshah-tsvwg-lln-diffserv-recommendations-01, August 2013.
   [I-D.thubert-6lowpan-backbone-router]
              Thubert, P., "6LoWPAN Backbone Router", Internet-Draft
              draft-thubert-6lowpan-backbone-router-03, February 2013.
   [I-D.thubert-roll-flow-label]
              Thubert, P., "Use of the IPv6 Flow Label within an LLN",
              Internet-Draft draft-thubert-roll-flow-label-02, November
              2012.
   [I-D.thubert-roll-forwarding-frags]
              Thubert, P. and J. Hui, "LLN Fragment Forwarding and
              Recovery", Internet-Draft draft-thubert-roll-forwarding-
              frags-02, September 2013.
   [I-D.wang-6tisch-6top-interface]
              Wang, Q., Vilajosana, X. and T. Watteyne, "6TiSCH
              Operation Sublayer (6top) Interface", Internet-Draft
              draft-wang-6tisch-6top-interface-01, February 2014.
   [I-D.wang-6tisch-6top-sublayer]
              Wang, Q., Vilajosana, X. and T. Watteyne, "6TiSCH
              Operation Sublayer (6top)", Internet-Draft draft-wang-
              6tisch-6top-00, October 2013.
13.3.  External Informative References
   [HART]     www.hartcomm.org, "Highway Addressable Remote Transducer,
              a group of specifications for industrial process and
              control devices administered by the HART Foundation", .
   [IEEE802.1TSNTG]
Thubert, Watteyne & AssiExpires August 16, 2014                [Page 23]


Internet-Draft            6TiSCH-architecture              February 2014
              IEEE Standards Association, "IEEE 802.1 Time-Sensitive
              Networks Task Group", March 2013, <http://www.ieee802.org/
              1/pages/avbridges.html>.
   [IEEE802154e]
              IEEE standard for Information Technology, "IEEE std.
              802.15.4e, Part.  15.4: Low-Rate Wireless Personal Area
              Networks (LR-WPANs) Amendament 1: MAC sublayer", April
              2012.
   [ISA100.11a]
              ISA, "ISA100, Wireless Systems for Automation", May 2008,
              <http://www.isa.org/Community/
              SP100WirelessSystemsforAutomation>.
Authors' Addresses
   Pascal Thubert, editor
   Cisco Systems, Inc
   Building D
   45 Allee des Ormes - BP1200
   MOUGINS - Sophia Antipolis, 06254
   FRANCE

   Phone: +33 497 23 26 34
   Email: pthubert@cisco.com
   Thomas Watteyne
   Linear Technology, Dust Networks Product Group
   30695 Huntwood Avenue
   Hayward, CA 94544
   USA

   Phone: +1 (510) 400-2978
   Email: twatteyne@linear.com
   Robert Assimiti
   Centero
   961 Indian Hills Parkway
   Marietta, GA 30068
   USA

   Phone: +1 404 461 9614
   Email: robert.assimiti@centerotech.com


Thubert, Watteyne & AssiExpires August 16, 2014                [Page 24]

Html markup produced by rfcmarkup 1.123, available from https://tools.ietf.org/tools/rfcmarkup/