[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 RFC 6412

   Network Working Group
   INTERNET-DRAFT
   Expires in: December 2005
                                                   Scott Poretsky
                                                   Quarry Technologies

                                                   Brent Imhoff
                                                   LightCore

                                                   June 2005

                        Terminology for Benchmarking
                      IGP Data Plane Route Convergence

                <draft-ietf-bmwg-igp-dataplane-conv-term-06.txt>

Intellectual Property Rights (IPR) statement:
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.

   Status of this Memo

   This document is an Internet-Draft and is in full conformance with
   all provisions of Section 10 of RFC2026.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force  (IETF), its areas, and its working groups.  Note that
   other groups June also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six
   months and June be updated, replaced, or obsoleted by other
   documents at any time.  It is inappropriate to use Internet-Drafts
   as reference material or to cite them other than as "work in
   progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

   ABSTRACT
   This draft describes the terminology for benchmarking IGP Route
   Convergence as described in Applicability document [1] and
   Methodology document [2].  The methodology and terminology is to
   be used for benchmarking Route Convergence and can be applied to
   any link-state IGP such as ISIS [3] and OSPF [4].  The data plane
   is measured to obtain the convergence benchmarking metrics
   described in [2].




Poretsky, Imhoff                                                                [Page 1]


INTERNET-DRAFT          Benchmarking Terminology for            February 2005
                      IGP Data Plane Route Convergence

   Table of Contents

     1. Introduction .................................................2
     2. Existing definitions .........................................3
     3. Term definitions..............................................3
        3.1 Convergence Event.........................................3
        3.2 Route Convergence.........................................4
        3.3 Network Convergence.......................................4
        3.4 Full Convergence..........................................5
        3.5 Convergence Packet Loss...................................5
        3.6 Convergence Event Instant.................................6
        3.7 Convergence Recovery Instant..............................6
        3.8 Rate-Derived Convergence Time.............................7
        3.9 Convergence Event Transition..............................7
        3.10 Convergence Recovery Transition..........................8
        3.11 Loss-Derived Convergence Time............................8
        3.12 Sustained Forwarding Convergence Time....................9
        3.13 Restoration Convergence Time.............................9
        3.14 Packet Sampling Interval.................................10
        3.15 Local Interface..........................................11
        3.16 Neighbor Interface.......................................11
        3.17 Remote Interface.........................................11
        3.18 Preferred Egress Interface...............................12
        3.19 Next-Best Egress Interface...............................12
        3.20 Stale Forwarding.........................................13
        3.21 Nested Convergence Events................................13
     4. Security Considerations.......................................13
     5. Normative References..........................................14
     6. Author's Address..............................................14

   1. Introduction
   This draft describes the terminology for benchmarking IGP Route
   Convergence.  The motivation and applicability for this
   benchmarking is provided in [1].  The methodology to be used for
   this benchmarking is described in [2].  The methodology and
   terminology to be used for benchmarking Route Convergence can be
   applied to any link-state IGP such as ISIS [3] and OSPF [4].  The
   data plane is measured to obtain black-box (externally observable)
   convergence benchmarking metrics.  The purpose of this document is
   to introduce new terms required to complete execution of the IGP
   Route Convergence Methodology [2].  These terms apply to IPv4 and
   IPv6 traffic as well as IPv4 and IPv6 IGPs.

   An example of Route Convergence as observed and measured from the
   data plane is shown in Figure 1.  The graph in Figure 1 shows
   Forwarding Rate versus Time.  Time 0 on the X-axis is on the far
   right of the graph.  The components of the graph and metrics are
   defined in the Term Definitions section.




Poretsky, Imhoff                                                                [Page 2]


INTERNET-DRAFT          Benchmarking Terminology for            February 2005
                      IGP Data Plane Route Convergence

                           Convergence    Convergence
                           Recovery         Event
                           Instant         Instant      Time = 0sec
        Maximum                ^              ^             ^
        Forwarding Rate--> ----\    Packet   /---------------
                                \    Loss   /<----Convergence
              Convergence------->\         /      Event Transition
        Recovery Transition       \       /
                                   \_____/<------Packet Loss

        X-axis = Time
        Y-axis = Forwarding Rate
                        Figure 1. Convergence Graph

   2.  Existing definitions
   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "June", and "OPTIONAL" in this
   document are to be interpreted as described in BCP 14, RFC 2119
   [Br97].  RFC 2119 defines the use of these key words to help make the
   intent of standards track documents as clear as possible.  While this
   document uses these keywords, this document is not a standards track
   document.

   3. Term Definitions
   3.1 Convergence Event

        Definition:
        The occurrence of a planned or unplanned action in the network
        that results in a change in the egress interface of the DUT for
        routed packets.

        Discussion:
        Convergence Events include link loss, routing protocol session
        loss, router failure, configuration change, and better next-hop
        learned via a routing protocol.

        Measurement Units:
        N/A

        Issues:
        None

        See Also:
        Convergence Packet Loss
        Convergence Event Instant






Poretsky, Imhoff                                                                [Page 3]


INTERNET-DRAFT          Benchmarking Terminology for            February 2005
                      IGP Data Plane Route Convergence

   3.2 Route Convergence

        Definition:
        Recovery from a Convergence Event indicated by the DUT
        forwarding rate equal to the offered load.

        Discussion:
        Route Convergence is the action of all components of the router
        being updated with the most recent route change(s) including the
        RIB and FIB, along with software and hardware tables. Route
        Convergence can be observed externally by the rerouting of data
        Traffic to a new egress interface.

        Measurement Units:
        N/A

        Issues:
        None

        See Also:
        Network Convergence
        Full Convergence
        Convergence Event


   3.3 Network Convergence

        Definition:
        The completion of updating of all routing tables, including the
        FIB, in all routers throughout the network.

        Discussion:
        Network Convergence is bounded by the sum of Route Convergence
        for all routers in the network.  Network Convergence can be
        determined by recovery of the forwarding rate to equal the offered
        load, no Stale Forwarding, and no blenders[5][6].

        Measurement Units:
        N/A

        Issues:
        None

        See Also:
        Route Convergence
        Stale Forwarding






Poretsky, Imhoff                                                                [Page 4]


INTERNET-DRAFT          Benchmarking Terminology for            February 2005
                      IGP Data Plane Route Convergence

   3.4 Full Convergence
        Definition:
        Route Convergence for an entire FIB.

        Discussion:
        When benchmarking convergence it is useful to measure
        the time to converge an entire FIB.  For example,
        a Convergence Event can be produced for an OSPF table of
        5000 routes so that the time to converge routes 1 through
        5000 is measured.  Full Convergence is externally observable
        from the data plane when the forwarding rate on the Next-Best
        Egress Interface equals the offered load.

        Measurement Units:
        N/A

        Issues:
        None

        See Also:
        Network Convergence
        Route Convergence
        Convergence Event

   3.5 Convergence Packet Loss

        Definition:
        The amount of packet loss produced by a Convergence Event
        until Route Convergence occurs.

        Discussion:
        Packet loss can be observed as a reduction of forwarded traffic from
        the maximum forwarding rate.  Convergence Packet Loss include packets
        that were lost and packets that were delayed due to buffering.
        Convergence Packet Loss June or June not reach 100%.

        Measurement Units:
        number of packets

        Issues:
        None

        See Also:
        Route Convergence
        Convergence Event
        Rate-Derived Convergence Time
        Loss-Derived Convergence Time





Poretsky, Imhoff                                                                [Page 5]


INTERNET-DRAFT          Benchmarking Terminology for            February 2005
                      IGP Data Plane Route Convergence

   3.6 Convergence Event Instant

        Definition:
        The time instant that a Convergence Event becomes observable in the
        data plane.

        Discussion:
        Convergence Event Instant is observable from the data
        plane as the precise time that the device under test begins
        to exhibit packet loss.

        Measurement Units:
        hh:mm:ss:uuu

        Issues:
        None

        See Also:
        Convergence Event
        Convergence Packet Loss
        Convergence Recovery Instant

   3.7 Convergence Recovery Instant

        Definition:
        The time instant that Full Convergence is measured
        and then maintained for an interval of duration equal to
        the Sustained Forwarding Convergence Time

        Discussion:
        Convergence Recovery Instant is measurable from the data
        plane as the precise time that the device under test
        achieves Full Convergence.

        Measurement Units:
        hh:mm:ss:uuu

        Issues:
        None

        See Also:
        Sustained Forwarding Convergence Time
        Convergence Packet Loss
        Convergence Event Instant








Poretsky, Imhoff                                                                [Page 6]


INTERNET-DRAFT          Benchmarking Terminology for            February 2005
                      IGP Data Plane Route Convergence

   3.8 Rate-Derived Convergence Time
        Definition:
        The amount of time for Convergence Packet Loss to persist upon
        occurrence of a Convergence Event until occurrence of Route
        Convergence.

        Rate-Derived Convergence Time can be measured as the time
        difference from the Convergence Event Instant to the
        Convergence Recovery Instant, as shown with Equation 1.

        (eq 1)  Rate-Derived Convergence Time =
                Convergence Recovery Instant - Convergence Event Instant.

        Discussion:
        Rate-Derived Convergence Time should be measured at the maximum
        forwarding rate.  Failure to achieve Full Convergence results in
        a Rate-Derived Convergence Time benchmark of infinity.

        Measurement Units:
        seconds/milliseconds

        Issues:
        None

        See Also:
        Convergence Packet Loss
        Convergence Recovery Instant
        Convergence Event Instant
        Full Convergence

   3.9 Convergence Event Transition
        Definition:
        The characteristic of a router in which forwarding rate
        gradually reduces to zero after a Convergence Event.

        Discussion:
        The Convergence Event Transition is best observed for
        Full Convergence.  The Convergence Event Transition June
        not be linear.

        Measurement Units:
        seconds/milliseconds

        Issues:
        None

        See Also:
        Convergence Event
        Rate-Derived Convergence Time
        Convergence Packet Loss
        Convergence Recovery Transition

Poretsky, Imhoff                                                                [Page 7]


INTERNET-DRAFT          Benchmarking Terminology for            February 2005
                      IGP Data Plane Route Convergence

   3.10 Convergence Recovery Transition

        Definition:
        The characteristic of a router in which forwarding rate
        gradually increases to equal the offered load.

        Discussion:
        The Convergence Recovery Transition is best observed for
        Full Convergence.  The Convergence Event Transition June
        not be linear.

        Measurement Units:
        seconds/milliseconds

        Issues:
        None

        See Also:
        Full Convergence
        Rate-Derived Convergence Time
        Convergence Packet Loss
        Convergence Event Transition

   3.11 Loss-Derived Convergence Time

        Definition:
        The amount of time it takes for Route Convergence to
        to be achieved as calculated from the Convergence Packet
        Loss.  Loss-Derived Convergence Time can be calculated
        from Convergence Packet Loss that occurs due to a
        Convergence Event and Route Convergence.as shown with
        Equation 2.

        (eq 2) Loss-Derived Convergence Time =
                Convergence Packets Loss / Offered Load
                NOTE: Units for this measurement are
                packets / packets/second = seconds

        Discussion:
        Loss-Derived Convergence Time gives a better than
        actual result when converging many routes simultaneously.
        Rate-Derived Convergence Time takes the Convergence Recovery
        Transition into account, but Loss-Derived Convergence Time
        ignores the Route Convergence Recovery Transition because
        it is obtained from the measured Convergence Packet Loss.
        Ideally, the Convergence Event Transition and Convergence
       Recovery Transition are instantaneous so that the
        Rate-Derived Convergence Time = Loss-Derived Convergence Time.
        However, router implementations are less than ideal.
        For these reasons the preferred reporting benchmark for IGP
        Route Convergence is the Rate-Derived Convergence Time.

Poretsky, Imhoff                                                                [Page 8]


INTERNET-DRAFT          Benchmarking Terminology for            February 2005
                      IGP Data Plane Route Convergence

        Guidelines for reporting Loss-Derived Convergence Time are
        provided in [2].

        Measurement Units:
        seconds/milliseconds

        Issues:
        None


        See Also:
        Route Convergence
        Convergence Packet Loss
        Rate-Derived Convergence Time
        Convergence Event Transition
        Convergence Recovery Transition

   3.12 Sustained Forwarding Convergence Time

        Definition:
        The amount of time for which Full Convergence is maintained without
        additional packet loss.

        Discussion:
        The purpose of the Sustained Forwarding Convergence Time is to produce
        Convergence Time benchmarks protected against fluctuation in Forwarding
        Rate after Full Convergence is observed.  The Sustained Forwarding
        Convergence Time to be used is calculated as shown in Equation 3.

        (eq 3)
        Sustained Forwarding Convergence Time =
        5 x (# routes in FIB) / (Offered Load)

        for which at least one packet per destination MUST be received at
        the DUT.

        Measurement Units:
        seconds or milliseconds

        Issues: None

        See Also:
        Full Convergence
        Convergence Recovery Instant

   3.13 Restoration Convergence Time

        Definition:
        The amount of time for the router under test to restore
        traffic to the original outbound port after recovery from
        a Convergence Event.

Poretsky, Imhoff                                                                [Page 9]


INTERNET-DRAFT          Benchmarking Terminology for            February 2005
                      IGP Data Plane Route Convergence

        Discussion:
        Restoration Convergence Time is the amount of time to
        Converge back to the original outbound port.  This is achieved
        by recovering from the Convergence Event, such as restoring
        the failed link.  Restoration Convergence Time is measured
        using the Rate-Derived Convergence Time calculation technique,
        as provided in Equation 1.  It is possible, but not desired
        to have the Restoration Convergence Time differ from the
        Rate-Derived Convergence Time.

        Measurement Units:
        seconds or milliseconds

        Issues:
        None

        See Also:
        Convergence Event
        Rate-Derived Convergence Time


   3.14 Packet Sampling Interval
        Definition:
        The interval at which the tester (test equipment) polls to make
        measurements for arriving packet flows.

        Discussion:
        Metrics measured at the Packet Sampling Interval June include
        Forwarding Rate and Convergence Packet Loss.

        Measurement Units:
        seconds or milliseconds

        Issues:
        Packet Sampling Interval can influence the Convergence Graph.
        This is particularly true as implementations achieve Full
        Convergence in less than 1 second.  The Convergence Event
        Transition and Convergence Recovery Transition can become
        exaggerated when the Packet Sampling Interval is too long.
        This will produce a larger than actual Rate-Derived
        Convergence Time.  The recommended value for configuration
        of the Packet Sampling Interval is provided in [2].

        See Also:
        Convergence Packet Loss
        Convergence Event Transition
        Convergence Recovery Transition





Poretsky, Imhoff                                                                [Page 10]


INTERNET-DRAFT          Benchmarking Terminology for            February 2005
                      IGP Data Plane Route Convergence

   3.15 Local Interface
        Definition:
        An interface on the DUT.

        Discussion:
        None

        Measurement Units:
        N/A


        Issues:
        None

        See Also:
        Neighbor Interface
         Remote Interface

   3.16 Neighbor Interface

        Definition:
        The interface on the neighbor router or tester that is
        directly linked to the DUT's Local Interface.

        Discussion:
        None

        Measurement Units:
        N/A

        Issues:
        None

        See Also:
        Local Interface
        Remote Interface

   3.17  Remote Interface

        Definition:
        An interface on a neighboring router that is not directly
        connected to any interface on the DUT.

        Discussion:
        None

        Measurement Units:
        N/A

        Issues:
        None

Poretsky, Imhoff                                                                [Page 11]


INTERNET-DRAFT          Benchmarking Terminology for            February 2005
                      IGP Data Plane Route Convergence

        See Also:
        Local Interface
        Neighbor Interface

   3.18 Preferred Egress Interface

        Definition:
        The outbound interface from the DUT for traffic routed to the
        preferred next-hop.



        Discussion:
        Preferred Egress Interface is the egress interface prior to
        a Convergence Event

        Measurement Units:
        N/A

        Issues:
        None

        See Also:
        Next-Best Egress Interface

   3.19 Next-Best Egress Interface

        Definition:
        The outbound interface from the DUT for traffic routed to the
        second-best next-hop.  It is the same media type and link speed
        as the Preferred Egress Interface

        Discussion:
         Next-Best Egress Interface is the egress interface after
        a Convergence Event.

        Measurement Units:
        N/A

        Issues:
        None

        See Also:
        Preferred Egress Interface








Poretsky, Imhoff                                                                [Page 12]


INTERNET-DRAFT          Benchmarking Terminology for            February 2005
                      IGP Data Plane Route Convergence

  3.20 Stale Forwarding
        Definition:
        Forwarding of traffic to route entries that no longer exist
        or to route entries with next-hops that are no longer preferred.

        Discussion:
        Stale Forwarding can be caused by a Convergence Event and is
        also known as a "black-hole" since it June produce packet loss.
        Stale Forwarding exists until Network Convergence is achieved.

        Measurement Units:
        N/A

        Issues:
        None

        See Also:
        Network Convergence


   3.21 Nested Convergence Events
        Definition:
        The occurence of Convergence Event while the route table
        is converging from a prior Convergence Event.

        Discussion:
        The Convergence Events for a Nested Convergence Events
        MUST occur with different neighbors.  A common
        observation from a Nested Convergence Event will be
        the withdrawal of routes from one neighbor while the
        routes of another neighbor are being installed.

        Measurement Units:
        N/A

        Issues:
        None

        See Also:
        Convergence Event



   4. Security Considerations

        Documents of this type do not directly affect the security of
        Internet or corporate networks as long as benchmarking
        is not performed on devices or systems connected to operating
        networks.



Poretsky, Imhoff                                                                [Page 13]


INTERNET-DRAFT          Benchmarking Terminology for            February 2005
                      IGP Data Plane Route Convergence


   5. Normative References

   [1]   Poretsky, S., "Benchmarking Applicability for IGP Data Plane
         Route Convergence", draft-ietf-bmwg-igp-dataplane-conv-app-05,
         work in progress, February 2005.

   [2]   Poretsky, S., "Benchmarking Methodology for IGP Data Plane
         Route Convergence", draft-ietf-bmwg-igp-dataplane-conv-meth-05,
         work in progress, February 2005.

   [3]   Callon, R., "Use of OSI IS-IS for Routing in TCP/IP and Dual
         Environments", RFC 1195, December 1990.

   [4]   Moy, J., "OSPF Version 2", RFC 2328, IETF, April 1998.

   [5]   S. Casner, C. Alaettinoglu, and C. Kuan, "A Fine-Grained View
         of High Performance Networking", NANOG 22, June 2001.

   [6]   L. Ciavattone, A. Morton, and G. Ramachandran, "Standardized
         Active Measurements on a Tier 1 IP Backbone", IEEE Communications
         Magazine, pp90-97, June, 2003.

  6. Author's Address

        Scott Poretsky
        Quarry Technologies
        8 New England Executive Park
        Burlington, MA 01803
        USA
        Phone: + 1 781 395 5090
        EMail: sporetsky@quarrytech.com

        Brent Imhoff
        USA
        EMail: bimhoff@planetspork.com


Intellectual Property Statement

The IETF takes no position regarding the validity or scope of any Intel-
lectual Property Rights or other rights that might be claimed to pertain
to the implementation or use of the technology described in this docu-
ment or the extent to which any license under such rights might or might
not be available; nor does it represent that it has made any independent
effort to identify any such rights.  Information on the procedures with
respect to rights in RFC documents can be found in BCP 78 and BCP 79.





Poretsky, Imhoff                                                                [Page 14]


INTERNET-DRAFT          Benchmarking Terminology for            February 2005
                      IGP Data Plane Route Convergence


Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an attempt
made to obtain a general license or permission for the use of such
proprietary rights by implementers or users of this specification can be
obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.

The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary rights
that June cover technology that June be required to implement this stan-
dard.  Please address the information to the IETF at ietf-ipr@ietf.org.

Disclaimer of Warranty

This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR
IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMA-
TION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Copyright Statement

Copyright (C) The Internet Society (2005).  This document is subject to
the rights, licenses and restrictions contained in BCP 78, and except as
set forth therein, the authors retain all their rights.
























Poretsky, Imhoff                                                                [Page 15]


Html markup produced by rfcmarkup 1.129b, available from https://tools.ietf.org/tools/rfcmarkup/