[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]
Versions: (draft-nadeau-ccamp-gmpls-te-mib)
00 01 03 04 05 06 07 08 09 10 11 12
13 14 15 16 RFC 4802
Internet Working Group Thomas D. Nadeau, Ed.
Internet Draft Cisco Systems, Inc.
Proposed Status: Standards Track
Expires: July 2005 Adrian Farrel, Ed.
Old Dog Consulting
February 2005
Generalized Multiprotocol Label Switching (GMPLS) Traffic
Engineering Management Information Base
draft-ietf-ccamp-gmpls-te-mib-08.txt
Status of this Memo
By submitting this Internet-Draft, I certify that any applicable
patent or other IPR claims of which I am aware have been disclosed,
and any of which I become aware will be disclosed, in accordance with
RFC 3668.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as
Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for Generalized
Multiprotocol Label Switching (GMPLS) based traffic engineering.
Nadeau and Farrel (Editors) [Page 1]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
Table of Contents
1. Introduction ........................................... 2
1.1. Migration Strategy ................................... 3
2. Terminology ............................................ 3
3. The SNMP Management Framework .......................... 3
4. Outline ................................................ 4
4.1. Summary of GMPLS Traffic Engineering MIB Module ...... 4
5. Brief Description of GMPLS TE MIB Objects .............. 5
5.1. gmplsTunnelTable ..................................... 5
5.2. gmplsTunnelHopTable .................................. 5
5.3. gmplsTunnelARHopTable ................................ 5
5.4. gmplsTunnelCHopTable ................................. 5
5.5. gmplsTunnelErrorTable ................................ 5
5.6. gmplsTunnelReversePerfTable .......................... 6
6. Cross-referencing to the mplsLabelTable ................ 6
7. Example of GMPLS Tunnel Setup .......................... 7
8. GMPLS Traffic Engineering MIB Module .... ............. 10
9. Security Considerations ............................... 44
10. Acknowledgments ...................................... 45
11. IANA Considerations .................................. 45
11.1. IANA Considerations for GMPLS-TE-STD-MIB ........... 45
12. References ........................................... 45
12.1. Normative Refenerces ............................... 45
12.2. Informational References ........................... 47
13. Authors' Addresses ................................... 48
14. Full Copyright Statement ............................. 49
15. Intellectual Property Notice ......................... 49
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects for modeling
Generalized Multiprotocol Label Switching (GMPLS) [RFC3945] based
traffic engineering. The tables and objects defined in this document
extend those defined in the equivalent document for MPLS traffic
engineering [RFC3812], and management of GMPLS traffic engineering is
built on management of MPLS traffic engineering.
This MIB module should be used in conjunction with the companion
document [GMPLSLSRMIB] for GMPLS based traffic engineering
configuration and management.
Comments should be made direct to the CCAMP mailing list at
ccamp@ops.ietf.org.
Nadeau and Farrel (Editors) [Page 2]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in BCP 14, RFC 2119,
reference [RFC2119].
1.1. Migration Strategy
This MIB module extends the traffic engineering MIB module defined
for use with MPLS [RFC3812]. It provides additions for support of
GMPLS tunnels.
The companion document for modeling and managing GMPLS based LSRs
[GMPLSLSRMIB] extends MPLS LSR MIB [RFC3813] with the same
intentions.
Textual conventions and OBJECT-IDENTIFIERS are defined in [RFC3811]
and [GMPLSTCMIB].
2. Terminology
This document uses terminology from the MPLS architecture document
[RFC3031], from the GMPLS architecture document [RFC3945], and from
the MPLS Traffic Engineering MIB [RFC3812]. Some frequently used
terms are described next.
An explicitly routed LSP (ERLSP) is referred to as a GMPLS tunnel. It
consists of in-segment(s) and/or out-segment(s) at the egress/ingress
LSRs, each segment being associated with one GMPLS enabled interface.
These are also referred to as tunnel segments.
Additionally, at an intermediate LSR, we model a connection as
consisting of one or more in-segments and/or one or more
out-segments. The binding or interconnection between in-segments and
out-segments in performed using a cross-connect.
These segment and cross-connect objects are defined in the MPLS Label
Switch Router MIB [RFC3813], but see also the GMPLS Label Switch
Router MIB [GMPLSLSRMIB] for the GMPLS-specific extensions to these
objects.
3. The SNMP Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Nadeau and Farrel (Editors) [Page 3]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
4. Outline
Support for GMPLS traffic-engineered tunnels requires the following
configuration.
- Setting up tunnels with appropriate MPLS configuration parameters
using [RFC3812].
- Extending the tunnels with GMPLS configuration parameters.
- Configuring tunnel loose and strict source routed hops.
These actions may need to be accompanied with corresponding actions
using [RFC3813] and [GMPLSLSRMIB] to establish and configure tunnel
segments, if this is done manually. Also, the in-segment and
out-segment performance tables, mplsInSegmentPerfTable and
mplsOutSegmentPerfTable [RFC3813], should be used to determine
performance of the tunnels and tunnel segments although it should be
noted that those tables may not be appropriate for measuring
performance on some types of GMPLS links.
4.1. Summary of GMPLS Traffic Engineering MIB Module
The MIB objects for performing the actions listed above that cannot
be performed solely using the MIB objects defined in [RFC3812]
consist of the following tables.
- Tunnel Table (gmplsTunnelTable) for providing GMPLS-specific
tunnel configuration parameters.
- Tunnel specified, actual, and computed hop tables
(gmplsTunnelHopTable, gmplsTunnelARHopTable, and
gmplsTunnelCHopTable) for providing additional configuration of
strict and loose source routed tunnel hops.
- Performance and error reporting tables (gmplsTunnelReversePerfTable
and gmplsTunnelErrorTable).
These tables are described in the subsequent sections.
Additionally, this MIB module contains a new Notification.
- The GMPLS Tunnel Down Notification (gmplsTunnelDown) is intended to
be used in place of the mplsTunnelDown Notification defined in
[RFC3812]. As well as indicating that a tunnel has transitioned to
operational down state, this new Notificaiton indicates the cause
of the failure.
Nadeau and Farrel (Editors) [Page 4]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
5. Brief Description of GMPLS TE MIB Objects
The objects described in this section support the functionality
described in [RFC3473] and [RFC3472] for GMPLS tunnels.
The tables support both manually configured and signaled tunnels.
5.1. gmplsTunnelTable
The gmplsTunnelTable extends the MPLS traffic engineering MIB module
to allow GMPLS tunnels to be created between an LSR and a remote
endpoint, and existing GMPLS tunnels to be reconfigured or removed.
Note that we only support point-to-point tunnel segments, although
multi-point-to-point and point-to-multi-point connections are
supported by an LSR acting as a cross-connect.
Each tunnel can thus have one out-segment originating at an LSR
and/or one in-segment terminating at that LSR.
5.2. gmplsTunnelHopTable
The gmplsTunnelHopTable is used to indicate additional parameters for
the hops, strict or loose, of a GMPLS tunnel defined in
gmplsTunnelTable, when it is established using signaling. Multiple
tunnels may share hops by pointing to the same entry in this table.
5.3. gmplsTunnelARHopTable
The gmplsTunnelARHopTable is used to indicate the actual hops
traversed by a tunnel as reported by the signaling protocol after the
tunnel is setup. The support of this table is optional since not all
GMPLS signaling protocols support this feature.
5.4. gmplsTunnelCHoptable
The gmplsTunnelCHopTable lists the actual hops computed by a
constraint-based routing algorithm based on the gmplsTunnelHopTable.
The support of this table is optional since not all implementations
support computation of hop lists using a constraint-based routing
protocol.
5.5. gmplsTunnelErrorTable
The gmplsTunnelErrorTable provides access to information about the
last error that occurred on each tunnel known about by the MIB. It
indicates the nature of the error, when and how it was reported and
can give recovery advice through a display string.
Nadeau and Farrel (Editors) [Page 5]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
5.6. gmplsTunnelReversePerfTable
gmplsTunnelReversePerfTable provides additional counters to measure
the performance of bidirectional GMPLS tunnels in which packets are
visible. It supplements the counters in mplsTunnelPerfTable and
augments gmplsTunnelTable.
Note that not all counters may be appropriate or available for some
types of tunnel.
6. Cross-referencing to the gmplsLabelTable
The gmplsLabelTable is found in a MIB module in [GMPLSLSRMIB] and
provides a way to model labels in a GMPLS system where labels might
not be simple 32 bit integers.
The hop tables in this document (gmplsHopTable, gmplsCHopTable and
gmplsARHopTable) and the segment tables in the [RFC3813]
(mplsInSegmentTable and mplsOutSegmentTable) contain objects with
syntax MplsLabel.
MplsLabel (defined in [RFC3811]) is a 32-bit integer that is capable
of representing any MPLS label and most GMPLS labels. However, some
GMPLS labels are larger than 32 bits and may be of arbitrary length.
Further, some labels that may be safely encoded in 32 bits are
constructed from multiple sub-fields. Additionally, some GMPLS
technologies support the concatenation of individual labels to
represent a data flow carried as multiple sub-flows.
These GMPLS cases require that something other than a simple 32-bit
integer is made available to represent the labels. This is achieved
through the gmplsLabelTable contained in [GMPLSLSRMIB].
The tables in this document and [RFC3813] that include objects with
syntax MplsLabel also include companion objects that are row
pointers. If the row pointer is set to zeroDotZero (0.0) then object
of syntax MplsLabel contains the label encoded as a 32-bit integer.
But otherwise the row pointer indicates a row in another MIB table
that includes the label. In these cases, the row pointer may indicate
a row in the gmplsLabelTable.
This provides both a good way to support legacy systems that
implement the previous version of this MIB module [RFC3812], and a
significant simplification in GMPLS systems that are limited to a
single, simple label type.
Note that gmplsLabelTable supports concatenated labels through the
use of a label sub-index (gmplsLabelSubindex).
Nadeau and Farrel (Editors) [Page 6]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
7. Example of GMPLS Tunnel Setup
This section contains an example of which MIB objects should be
modified to create a GMPLS tunnel. This example shows a best effort,
loosely routed, bidirectional traffic engineered tunnel, which spans
two hops of a simple network, uses Generalized Label requests with
Lambda encoding, has label recording and shared link layer
protection. Note that these objects should be created on the
"head-end" LSR.
First in the mplsTunnelTable:
{
mplsTunnelIndex = 1,
mplsTunnelInstance = 1,
mplsTunnelIngressLSRId = 123.123.125.1,
mplsTunnelEgressLSRId = 123.123.126.1,
mplsTunnelName = "My first tunnel",
mplsTunnelDescr = "Here to there and back again",
mplsTunnelIsIf = true (1),
mplsTunnelXCPointer = mplsXCIndex.3.0.0.12,
mplsTunnelSignallingProto = none (1),
mplsTunnelSetupPrio = 0,
mplsTunnelHoldingPrio = 0,
mplsTunnelSessionAttributes = recordRoute (4),
mplsTunnelOwner = snmp (2),
mplsTunnelLocalProtectInUse = false (0),
mplsTunnelResourcePointer = mplsTunnelResourceIndex.6,
mplsTunnelInstancePriority = 1,
mplsTunnelHopTableIndex = 1,
mplsTunnelPrimaryInstance = 0,
mplsTunnelIncludeAnyAffinity = 0,
mplsTunnelIncludeAllAffinity = 0,
mplsTunnelExcludeAnyAffinity = 0,
mplsTunnelPathInUse = 1,
mplsTunnelRole = head(1),
mplsTunnelRowStatus = createAndWait (5),
}
In gmplsTunnelTable(1,1,123.123.125.1,123.123.126.1):
{
gmplsTunnelUnnumIf = true (1),
gmplsTunnelAttributes = labelRecordingRequired (1),
gmplsTunnelLSPEncoding = tunnelLspLambda (8),
gmplsTunnelSwitchingType = lsc (150),
gmplsTunnelLinkProtection = shared (2),
gmplsTunnelGPid = lambda (37),
gmplsTunnelSecondary = false(0),
gmplsTunnelDirection = bidirectional (1)
gmplsTunnelPathComp = explicit(2),
Nadeau and Farrel (Editors) [Page 7]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
gmplsTunnelUpNotRecip = 0x7B7B7D01,
gmplsTunnelDownNotRecip = 0x00000000,
gmplsTunnelAdminStatusFlags = 0,
gmplsTunnelExtraParamsPtr = 0.0
}
Entries in the mplsTunnelResourceTable, mplsTunnelHopTable and
gmplsTunnelHopTable are created and activated at this time.
In mplsTunnelResourceTable:
{
mplsTunnelResourceIndex = 6,
mplsTunnelResourceMaxRate = 0,
mplsTunnelResourceMeanRate = 0,
mplsTunnelResourceMaxBurstSize = 0,
mplsTunnelResourceRowStatus = createAndGo (4)
}
The next two instances of mplsTunnelHopEntry are used to denote the
hops this tunnel will take across the network.
The following denotes the beginning of the network, or the first hop.
We have used the fictitious LSR identified by "123.123.125.1" as our
example head-end router.
In mplsTunnelHopTable:
{
mplsTunnelHopListIndex = 1,
mplsTunnelPathOptionIndex = 1,
mplsTunnelHopIndex = 1,
mplsTunnelHopAddrType = ipV4 (1),
mplsTunnelHopIpv4Addr = 123.123.125.1,
mplsTunnelHopIpv4PrefixLen = 9,
mplsTunnelHopType = strict (1),
mplsTunnelHopRowStatus = createAndWait (5),
}
The following denotes the end of the network, or the last hop in our
example. We have used the fictitious LSR identified by
"123.123.126.1" as our end router.
In mplsTunnelHopTable:
{
mplsTunnelHopListIndex = 1,
mplsTunnelPathOptionIndex = 1,
mplsTunnelHopIndex = 2,
mplsTunnelHopAddrType = ipV4 (1),
mplsTunnelHopIpv4Addr = 123.123.126.1,
mplsTunnelHopIpv4PrefixLen = 9,
mplsTunnelHopType = loose (2),
Nadeau and Farrel (Editors) [Page 8]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
mplsTunnelHopRowStatus = createAndGo (4)
}
Now an associated entry in the gmplsTunnelHopTable is created to
provide additional GMPLS hop configuration indicating that the first
hop is an unnumbered link using explicit forward and reverse labels.
An entry in the gmplsLabelTable is created first to include the
explicit label.
In gmplsLabelTable:
{
gmplsLabelInterface = 2,
gmplsLabelIndex = 1,
gmplsLabelSubindex = 0,
gmplsLabelType = gmplsFreeformGeneralizedLabel(3),
gmplsLabelFreeform = 0xFEDCBA9876543210
gmplsLabelRowStatus = createAndGo(4)
}
In gmplsTunnelHopTable(1,1,1):
{
gmplsTunnelHopLabelStatuses = forwardPresent(0)
+reversePresent(1),
gmplsTunnelHopExpLabelPtr = gmplsLabelTable (2, 1, 0)
gmplsTunnelHopExpRvrsLabelPtr = gmplsLabelTable (2, 1, 0)
}
The first hop is now activated:
In mplsTunnelHopTable(1,1,1):
{
mplsTunnelHopRowStatus = active (1)
}
No gmplsTunnelHopEntry is created for the second hop as it contains
no special GMPLS features.
Finally the mplsTunnelEntry is activated:
In mplsTunnelTable(1,1,123.123.125.1,123.123.126.1)
{
mplsTunnelRowStatus = active(1)
}
Nadeau and Farrel (Editors) [Page 9]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
8. GMPLS Traffic Engineering MIB Module
GMPLS-TE-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
Integer32, Unsigned32, Counter32,
Counter64, IpAddress, zeroDotZero
FROM SNMPv2-SMI -- [RFC2578]
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF -- [RFC2580]
TruthValue, TimeStamp, DisplayString, RowPointer
FROM SNMPv2-TC -- [RFC2579]
InetAddress, InetAddressType
FROM INET-ADDRESS-MIB -- [RFC3291]
mplsTunnelIndex, mplsTunnelInstance, mplsTunnelIngressLSRId,
mplsTunnelEgressLSRId, mplsTunnelHopListIndex,
mplsTunnelHopPathOptionIndex, mplsTunnelHopIndex,
mplsTunnelARHopListIndex, mplsTunnelARHopIndex,
mplsTunnelCHopListIndex, mplsTunnelCHopIndex,
mplsTunnelEntry,
mplsTunnelAdminStatus, mplsTunnelOperStatus
FROM MPLS-TE-STD-MIB -- [RFC3812]
mplsStdMIB
FROM MPLS-TC-STD-MIB -- [RFC3811]
;
gmplsTeStdMIB MODULE-IDENTITY
LAST-UPDATED
"200502090001Z" -- 9 February 2005 00:00:01 GMT
ORGANIZATION
"Common Control And Measurement Plane (CCAMP) Working Group"
CONTACT-INFO
" Thomas D. Nadeau
Cisco Systems, Inc.
Email: tnadeau@cisco.com
Adrian Farrel
Old Dog Consulting
Email: adrian@olddog.co.uk
Comments about this document should be emailed direct to the
CCAMP working group mailing list at ccamp@ops.ietf.org"
DESCRIPTION
"Copyright (C) The Internet Society (2004). The
initial version of this MIB module was published
in RFC xxxx. For full legal notices see the RFC
itself or see: http://www.ietf.org/copyrights/ianamib.html
Nadeau and Farrel (Editors) [Page 10]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
This MIB module contains managed object definitions
for GMPLS Traffic Engineering (TE) as defined in:
1. Generalized Multi-Protocol Label Switching (GMPLS)
Signaling Functional Description, Berger, L. (Editor),
RFC 3471, January 2003.
2. Generalized MPLS Signaling - RSVP-TE Extensions, Berger,
L. (Editor), RFC 3473, January 2003."
-- Revision history.
REVISION
"200502090001Z" -- 9 February 2005 00:00:01 GMT
DESCRIPTION
"Initial version issued as part of RFC XXXX."
::= { mplsStdMIB xx }
-- Top level components of this MIB.
-- Notifications
gmplsTeNotifications OBJECT IDENTIFIER ::= { gmplsTeStdMIB 0 }
-- tables, scalars
gmplsTeScalars OBJECT IDENTIFIER ::= { gmplsTeStdMIB 1 }
gmplsTeObjects OBJECT IDENTIFIER ::= { gmplsTeStdMIB 2 }
-- conformance
gmplsTeConformance OBJECT IDENTIFIER ::= { gmplsTeStdMIB 3 }
-- GMPLS Tunnel scalars.
gmplsTunnelsConfigured OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of GMPLS tunnels configured on this device. A GMPLS
tunnel is considered configured if an entry for the tunnel
exists in the gmplsTunnelTable and the associated
mplsTunnelRowStatus is active(1)."
::= { gmplsTeScalars 1 }
gmplsTunnelsActive OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of GMPLS tunnels active on this device. A GMPLS
tunnel is considered active if there is an entry in the
gmplsTunnelTable and the associated mplsTunnelOperStatus
for the tunnel is up(1)."
::= { gmplsTeScalars 2 }
-- End of GMPLS Tunnel scalars.
Nadeau and Farrel (Editors) [Page 11]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
-- GMPLS tunnel table.
gmplsTunnelTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsTunnelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The gmplsTunnelTable 'extends' the mplsTunnelTable.
It allows GMPLS tunnels to be created between an LSR
and a remote endpoint, and existing tunnels to be
reconfigured or removed.
Note that only point-to-point tunnel segments are
supported, although multi-point-to-point and
point-to-multi-point connections are supported by an LSR
acting as a cross-connect. Each tunnel can thus have
one out-segment originating at this LSR and/or one
in-segment terminating at this LSR.
The row status of an entry in this table is
controlled by mplsTunnelRowStatus in the
corresponding entry in mplsTunnelTable. That is,
it is not permitted to create a row in this table,
nor to modify an existing row, when the
corresponding mplsTunnelRowStatus has value
active(1).
The exception to this rule is the gmplsTunnelAdminStatusFlags
object, which can be modified whilst the tunnel is active."
::= { gmplsTeObjects 1 }
gmplsTunnelEntry OBJECT-TYPE
SYNTAX GmplsTunnelEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table in association with the
corresponding entry in the mplsTunnelTable
represents a GMPLS tunnel.
An entry can be created by a network administrator
or by an SNMP agent as instructed by a signaling
protocol."
INDEX {
mplsTunnelIndex,
mplsTunnelInstance,
mplsTunnelIngressLSRId,
mplsTunnelEgressLSRId
}
::= { gmplsTunnelTable 1 }
Nadeau and Farrel (Editors) [Page 12]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
GmplsTunnelEntry ::= SEQUENCE {
gmplsTunnelUnnumIf TruthValue,
gmplsTunnelAttributes BITS,
gmplsTunnelLSPEncoding Integer32,
gmplsTunnelSwitchingType Integer32,
gmplsTunnelLinkProtection BITS,
gmplsTunnelGPid Integer32,
gmplsTunnelSecondary TruthValue,
gmplsTunnelDirection INTEGER,
gmplsTunnelPathComp INTEGER,
gmplsTunnelUpNotRecip IpAddress,
gmplsTunnelDownNotRecip IpAddress,
gmplsTunnelAdminStatusFlags BITS,
gmplsTunnelExtraParamsPtr RowPointer
}
gmplsTunnelUnnumIf OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Denotes whether or not this tunnel corresponds to an
unnumbered interface represented in the interfaces
group table.
This object is only used if mplsTunnelIsIf is set to
'true'.
If both this object and the mplsTunnelIsIf object
are set to 'true', the originating LSR adds an
LSP_TUNNEL_INTERFACE_ID object to the outgoing Path
message.
This object contains information that is only used
by the terminating LSR."
REFERENCE
"Signalling Unnumbered Links in RSVP-TE, Kompella, K.
and Rekhter, Y., RFC 3477, January 2003."
DEFVAL { false }
::= { gmplsTunnelEntry 1 }
gmplsTunnelAttributes OBJECT-TYPE
SYNTAX BITS {
labelRecordingDesired (0)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This bitmask indicates optional parameters for this
tunnel. These bits should be taken in addition to
Nadeau and Farrel (Editors) [Page 13]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
those defined in mplsTunnelSessionAttributes in
order to determine the full set of options to be
signaled (for example SESSION_ATTRIBUTES flags in
RSVP-TE).
The following describes these bitfields:
labelRecordingDesired
This flag indicates that label information should be
included when doing a route record. This bit is not
valid unless the recordRoute bit is set."
REFERENCE
"RSVP-TE: Extensions to RSVP for LSP Tunnels, Awduche
et al, RFC 3209, December 2001."
DEFVAL { { } }
::= { gmplsTunnelEntry 2 }
gmplsTunnelLSPEncoding OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the encoding of the LSP being requested.
A value of zero indicates that GMPLS signaling is
not in use. Some objects in this MIB module may be
of use for MPLS signaling extensions that do not use
GMPLS signaling. By setting this object to zero, an
application may indicate that only those objects
meaningful in MPLS should be examined.
The values to use are currently defined in
Generalized Multi-Protocol Label Switching (GMPLS)
Signaling Functional Description, RFC 3471. Further
values may be defined in future RFCs.
tunnelLspPacket (1),
tunnelLspEthernet (2),
tunnelLspAnsiEtsiPdh (3),
-- the value 4 is deprecated
tunnelLspSdhSonet (5),
-- the value 6 is deprecated
tunnelLspDigitalWrapper (7),
tunnelLspLambda (8),
tunnelLspFiber (9),
-- the value 10 is deprecated
tunnelLspFiberChannel (11),
tunnelDigitalPath (12),
tunnelOpticalChannel (13)"
Nadeau and Farrel (Editors) [Page 14]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
REFERENCE
"1. Berger, L., et al., Generalized Multi-Protocol
Label Switching (GMPLS) Signaling Functional
Description, RFC 3471, January 2003.
2. D. Papadimitriou (Editor), Generalized MPLS
Signalling Extensions for G.709 Optical Transport
Networks Control, draft-ietf-ccamp-gmpls-g709-06.txt,
January 2004, work in progress."
DEFVAL { 0 }
::= { gmplsTunnelEntry 3 }
gmplsTunnelSwitchingType OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the type of switching that should be performed on
a particular link. This field is needed for links that
advertise more than one type of switching capability. Values
of this object are as the Switching Capability field defined
in Internet Draft OSPF Extensions in Support of Generalized
MPLS. Further values may be defined in future RFCs.
unknown (0),
psc1 (1),
psc2 (2),
psc3 (3),
psc4 (4),
l2sc (51),
tdm (100),
lsc (150),
fsc (200)
This object is only meaningful if
gmplsTunnelLSPEncoding is not set to 0."
REFERENCE
"1. Kompella, K., Rekhter, Y. (Editors), Routing Extensions in
Support of Generalized Multi-Protocol Label Switching,
draft-ietf-ccamp-gmpls-routing-09.txt, October 2003, work in
progress.
2. Berger, L., et al., Generalized Multi-Protocol
Label Switching (GMPLS) Signaling Functional
Description, RFC 3471, January 2003."
DEFVAL { 0 }
::= { gmplsTunnelEntry 4 }
Nadeau and Farrel (Editors) [Page 15]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
gmplsTunnelLinkProtection OBJECT-TYPE
SYNTAX BITS {
extraTraffic(0),
unprotected(1),
shared (2),
dedicatedOneToOne (3),
dedicatedOnePlusOne(4),
enhanced(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This bitmask indicates the level of link protection
required. A value of zero (no bits set) indicates
that any protection may be used.
The following describes these bitfields:
extraTraffic
Indicates that the LSP should use links that are
protecting other (primary) traffic. Such LSPs may
be preempted when the links carrying the (primary)
traffic being protected fail.
unprotected
Indicates that the LSP should not use any link layer
protection.
shared
Indicates that a shared link layer protection scheme,
such as 1:N protection, should be used to support the LSP.
dedicatedOneToOne
Indicates that a dedicated link layer protection scheme,
i.e., 1:1 protection, should be used to support the LSP.
dedicatedOnePlusOne
Indicates that a dedicated link layer protection scheme,
i.e., 1+1 protection, should be used to support the LSP.
enhanced
Indicates that a protection scheme that is more reliable than
Dedicated 1+1 should be used, e.g., 4 fiber BLSR/MS-SPRING.
This object is only meaningful if gmplsTunnelLSPEncoding is
not set to 0."
REFERENCE
"Berger, L., et al., Generalized Multi-Protocol
Label Switching (GMPLS) Signaling Functional
Description, RFC 3471, January 2003."
DEFVAL { { } }
::= { gmplsTunnelEntry 5 }
Nadeau and Farrel (Editors) [Page 16]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
gmplsTunnelGPid OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates the payload carried by the
LSP. It is only required when GMPLS will be used for
this LSP.
The values to use are currently defined in
Generalized Multi-Protocol Label Switching (GMPLS)
Signaling Functional Description, RFC 3471. Further
values may be defined in future RFCs.
unknown(0),
asynchE4(5),
asynchDS3T3(6),
asynchE3(7),
bitsynchE3(8),
bytesynchE3(9),
asynchDS2T2(10),
bitsynchDS2T2(11),
asynchE1(13),
bytesynchE1(14),
bytesynch31ByDS0(15),
asynchDS1T1(16),
bitsynchDS1T1(17),
bytesynchDS1T1(18),
VC11VC12(19),
ds1SFAsynch(22),
ds1ESFAsynch(23),
ds3M23Asynch(24),
ds3CBitParityAsynch(25),
vtLovc(26),
stsSpeHovc(27),
posNoScramble16BitCrc(28),
posNoScramble32BitCrc(29),
posScramble16BitCrc(30),
posScramble32BitCrc(31),
atm(32)
ethernet(33),
sdhSonet(34),
digitalwrapper(36),
lambda(37),
ansiEtsiPdh (38),
lapsSdh (40),
fddi (41),
dqdb (42),
fiberChannel3 (43),
hdlc (44),
Nadeau and Farrel (Editors) [Page 17]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
ethernetV2DixOnly (45),
ethernet802dot3Only (46),
g709ODUj (47),
g709OTUk (48),
g709CBRorCBRa (49),
g709CBRb (50),
g709BSOT (51),
g709BSNT (52),
gfpIPorPPP (53),
gfpEthernetMAC (54),
gfpEthernetPHY (55),
g709ESCON (56),
g709FICON (57),
g709FiberChannel (58)
This object is only meaningful if
gmplsTunnelLSPEncoding is not set to 0."
REFERENCE
"1. Berger, L., et al., Generalized Multi-Protocol
Label Switching (GMPLS) Signaling Functional
Description, RFC 3471, January 2003.
2. D. Papadimitriou (Editor), Generalized MPLS
Signalling Extensions for G.709 Optical Transport
Networks Control, draft-ietf-ccamp-gmpls-g709-06.txt,
January 2004, work in progress."
DEFVAL { 0 }
::= { gmplsTunnelEntry 6 }
gmplsTunnelSecondary OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates that the requested LSP is a secondary LSP.
This object is only meaningful if
gmplsTunnelLSPEncoding is not set to 0."
REFERENCE
"Berger, L., et al., Generalized Multi-Protocol
Label Switching (GMPLS) Signaling Functional
Description, RFC 3471, January 2003."
DEFVAL { false }
::= { gmplsTunnelEntry 7 }
gmplsTunnelDirection OBJECT-TYPE
SYNTAX INTEGER {
forward (0),
bidirectional (1)
}
MAX-ACCESS read-create
STATUS current
Nadeau and Farrel (Editors) [Page 18]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
DESCRIPTION
"Whether this tunnel carries forward data only (is
unidirectional) or is bidirectional.
Values of this object other than 'forward' are meaningful
only if gmplsTunnelLSPEncoding is not set to 0."
DEFVAL { forward }
::= { gmplsTunnelEntry 8 }
gmplsTunnelPathComp OBJECT-TYPE
SYNTAX INTEGER {
dynamicFull(1), -- CSPF fully computed
explicit(2), -- fully specified path
dynamicPartial(3) -- CSPF partially computed
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This value instructs the source node on how to perform
path computation on the explicit route specified by the
associated entries in the gmplsTunnelHopTable.
dynamicFull
The user specifies at least the source and
destination of the path and expects that the CSPF
will calculate the remainder of the path.
explicit
The user specifies the entire path for the tunnel to
take. This path may contain strict or loose hops.
Evaluation of the explicit route will be performed
hop by hop through the network.
dynamicPartial
The user specifies at least the source and
destination of the path and expects that the CSPF
will calculate the remainder of the path. The path
computed by CSPF is allowed to be only partially
computed allowing the remainder of the path to be
filled in across the network.
This object deprecates mplsTunnelHopEntryPathComp."
DEFVAL { dynamicFull }
::= { gmplsTunnelEntry 9 }
gmplsTunnelUpNotRecip OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the address of the upstream recipient for Notify
messages relating to this tunnel.
Nadeau and Farrel (Editors) [Page 19]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
This object is only valid when signaling a tunnel using
RSVP. It is also not valid at the tail end of the tunnel.
If set to 0, no Notify Request object will be included in
outgoing Path messages."
REFERENCE
"Generalized MPLS Signaling - RSVP-TE Extensions, Berger,
L. (Editor), RFC 3473, January 2003."
DEFVAL { '00000000'H } -- 0.0.0.0
::= { gmplsTunnelEntry 10 }
gmplsTunnelDownNotRecip OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates the address of the upstream recipient for Notify
messages relating to this tunnel.
This object is only valid when signaling a tunnel using
RSVP. It is also not valid at the head end of the tunnel.
If set to 0, no Notify Request object will be included in
outgoing Resv messages."
REFERENCE
"Generalized MPLS Signaling - RSVP-TE Extensions, Berger,
L. (Editor), RFC 3473, January 2003."
DEFVAL { '00000000'H } -- 0.0.0.0
::= { gmplsTunnelEntry 11 }
gmplsTunnelAdminStatusFlags OBJECT-TYPE
SYNTAX BITS {
delInProgress (0),
adminDown (1),
testing (2),
reflect (31)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Determines the setting of the Admin Status flags in the
Admin Status object or TLV, as described in
RFC 3471. Setting this field to a non-zero value will
result in the inclusion of the admin status object on
signaling messages.
This value of this object can be modified when the
corresponding mplsTunnelRowStatus and mplsTunnelAdminStatus
is active(1). By doing so, a new signaling message will be
triggered including the requested Admin Status object or
TLV."
Nadeau and Farrel (Editors) [Page 20]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
REFERENCE
"Berger, L., et al., Generalized Multi-Protocol
Label Switching (GMPLS) Signaling Functional
Description, RFC 3471, January 2003."
DEFVAL { { } }
::= { gmplsTunnelEntry 12 }
gmplsTunnelExtraParamsPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Some Tunnels will run over transports that can usefully support
technology-specific additional parameters (for example, SONET
resource usage). Such parameters can be supplied in an external
table and referenced from here.
A value of zeroDotzero in this attribute indicates that there
is no such additional information."
DEFVAL { zeroDotZero }
::= { gmplsTunnelEntry 13 }
-- End of gmplsTunnelTable
-- Begin gmplsTunnelHopTable
gmplsTunnelHopTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsTunnelHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The gmplsTunnelHopTable 'extends' the mplsTunnelHopTable.
It is used to indicate the explicit labels to be used in an
explicit path for a GMPLS tunnel defined in mplsTunnelTable
and gmplsTunnelTable, when it is established using signaling.
It does not insert new hops, but does define new values for
hops defined in mplsTunnelHopTable.
Each row in this table is indexed by the same
indexes as mplsTunnelHopTable. It is acceptable for
some rows in mplsTunnelHopTable to have
corresponding entries in this table and some to have
no corresponding entry in this table.
The storage type for an entry in this table is
inherited from mplsTunnelHopStorageType in the
corresponding entry in mplsTunnelHopTable.
The row status of an entry in this table is
controlled by mplsTunnelHopRowStatus in the
Nadeau and Farrel (Editors) [Page 21]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
corresponding entry in mplsTunnelHopTable. That is,
it is not permitted to create a row in this table,
nor to modify an existing row, when the
corresponding mplsTunnelHopRowStatus has value
active(1)."
REFERENCE
"Generalized MPLS Signaling - RSVP-TE Extensions, Berger,
L. (Editor), RFC 3473, January 2003."
::= { gmplsTeObjects 2 }
gmplsTunnelHopEntry OBJECT-TYPE
SYNTAX GmplsTunnelHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents additions to a
tunnel hop defined in mplsTunnelHopEntry. At an
ingress to a tunnel an entry in this table is
created by a network administrator for an ERLSP to
be set up by a signaling protocol. At transit and
egress nodes an entry in this table may be used to
represent the explicit path instructions received
using the signaling protocol."
INDEX {
mplsTunnelHopListIndex,
mplsTunnelHopPathOptionIndex,
mplsTunnelHopIndex
}
::= { gmplsTunnelHopTable 1 }
GmplsTunnelHopEntry ::= SEQUENCE {
gmplsTunnelHopLabelStatuses BITS,
gmplsTunnelHopExpLabel Unsigned32,
gmplsTunnelHopExpLabelPtr RowPointer,
gmplsTunnelHopExpRvrsLabel Unsigned32,
gmplsTunnelHopExpRvrsLabelPtr RowPointer
}
gmplsTunnelHopLabelStatuses OBJECT-TYPE
SYNTAX BITS {
forwardPresent (0),
reversePresent (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This bitmask indicates the presence of labels
indicated by the gmplsTunnelHopExpLabel or
gmplsTunnelHopExpLabelPtr and gmplsTunnelHopExpRvrsLabel
or gmplsTunnelHopExpRvrsLabel objects.
Nadeau and Farrel (Editors) [Page 22]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
For the Present bits, a set bit indicates that a
label is present for this hop in the route. This
allows zero to be a valid label value."
DEFVAL { { } }
::= { gmplsTunnelHopEntry 1 }
gmplsTunnelHopExpLabel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If gmplsTunnelHopLabelStatuses object indicates that a
forward label is present and gmplsTunnelHopExpLabelPtr
contains the value zeroDotZero, then the label to use on this
hop is found in this object encoded within a 32-bit integer."
::= { gmplsTunnelHopEntry 2 }
gmplsTunnelHopExpLabelPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the gmplsTunnelHopLabelStatuses object indicates
that a forward label is present, this object contains
a pointer to a row in another MIB table (such as the
gmplsLabelTable) that contains the label to use on
this hop in the forward direction.
If the gmplsTunnelHopLabelStatuses object indicates that
a forward label is present and this object contains the
value zeroDotZero, then the label to use on this hop is
found in the gmplsTunnelHopExpLabel object."
DEFVAL { zeroDotZero }
::= { gmplsTunnelHopEntry 3 }
gmplsTunnelHopExpRvrsLabel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the gmplsTunnelHopLabelStatuses object indicates that a
reverse label is present and gmplsTunnelHopExpRvrsLabelPtr
contains the value zeroDotZero, then the label to use on
this hop is found in this object encoded as a 32-bit integer."
::= { gmplsTunnelHopEntry 4 }
gmplsTunnelHopExpRvrsLabelPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS current
Nadeau and Farrel (Editors) [Page 23]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
DESCRIPTION
"If the gmplsTunnelHopLabelStatuses object indicates
that a reverse label is present, this object contains
a pointer to a row in another MIB table (such as the
gmplsLabelTable) that contains the label to use on
this hop in the reverse direction.
If the gmplsTunnelHopLabelStatuses object indicates that
a reverse label is present and this object contains the
value zeroDotZero, then the label to use on this hop is
found in the gmplsTunnelHopExpRvrsLabel object."
DEFVAL { zeroDotZero }
::= { gmplsTunnelHopEntry 5 }
-- End of gmplsTunnelHopTable
-- Tunnel Actual Route Hop table.
gmplsTunnelARHopTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsTunnelARHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The gmplsTunnelARHopTable 'extends' the
mplsTunnelARHopTable. It is used to indicate the
labels currently in use for a GMPLS tunnel defined
in mplsTunnelTable and gmplsTunnelTable, as reported
by the signaling protocol. It does not insert new
hops, but does define new values for hops defined in
mplsTunnelARHopTable.
Each row in this table is indexed by the same indexes as
mplsTunnelARHopTable. It is acceptable for some rows in
mplsTunnelARHopTable to have corresponding entries in this
table and some to have no corresponding entry in this table.
Note that since the information necessary to build
entries within this table is not provided by some
signaling protocols and might not be returned in all
cases of other signaling protocols, implementation
of this table and mplsTunnelARHopTable is optional.
Furthermore, since the information in this table is
actually provided by the signaling protocol after
the path has been set-up, the entries in this table
are provided only for observation, and hence, all
variables in this table are accessible exclusively
as read-only."
Nadeau and Farrel (Editors) [Page 24]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
REFERENCE
"1. Extensions to RSVP for LSP Tunnels, Awduche et
al, RFC 3209, December 2001
2. Generalized MPLS Signaling - RSVP-TE Extensions, Berger,
L. (Editor), RFC 3473, January 2003."
::= { gmplsTeObjects 3 }
gmplsTunnelARHopEntry OBJECT-TYPE
SYNTAX GmplsTunnelARHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents additions to a
tunnel hop visible in mplsTunnelARHopEntry. An entry
is created by the signaling protocol for a signaled
ERLSP set up by the signaling protocol.
At any node on the LSP (ingress, transit or egress)
Thus at this table and mplsTunnelARHopTable (if the
tables are supported and if the signaling protocol
is recording actual route information) contains the
actual route of the whole tunnel. If the signaling
protocol is not recording the actual route, this
table MAY report the information from the
gmplsTunnelHopTable or the gmplsTunnelCHopTable.
Note that the recording of actual labels is distinct
from the recording of the actual route in some
signaling protocols. This feature is enabled using
the gmplsTunnelAttributes object."
INDEX {
mplsTunnelARHopListIndex,
mplsTunnelARHopIndex
}
::= { gmplsTunnelARHopTable 1 }
GmplsTunnelARHopEntry ::= SEQUENCE {
gmplsTunnelARHopLabelStatuses BITS,
gmplsTunnelARHopExpLabel Unsigned32,
gmplsTunnelARHopExpLabelPtr RowPointer,
gmplsTunnelARHopExpRvrsLabel Unsigned32,
gmplsTunnelARHopExpRvrsLabelPtr RowPointer,
gmplsTunnelARHopProtection BITS
}
Nadeau and Farrel (Editors) [Page 25]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
gmplsTunnelARHopLabelStatuses OBJECT-TYPE
SYNTAX BITS {
forwardPresent (0),
reversePresent (1),
forwardGlobal (2),
reverseGlobal (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This bitmask indicates the presence and status of
labels indicated by the gmplsTunnelARHopExpLabel or
gmplsTunnelARHopExpLabelPtr and gmplsTunnelARHopExpRvrsLabel
or gmplsTunnelARHopExpRvrsLabelPtr objects.
For the Present bits, a set bit indicates that a label
is present for this hop in the route. For the Global bits,
a set bit indicates that the label comes from the Global
Label Space. A clear bit indicates that this is a
Per-Interface label. A Global bit only has meaning if the
corresponding Present bit is set."
::= { gmplsTunnelARHopEntry 1 }
gmplsTunnelARHopExpLabel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the gmplsTunnelARHopLabelStatuses object indicates
that a forward label is present and
gmplsTunnelARHopExpLabelPtr contains the value
zeroDotZero, then the label in use on this hop is
found in this object encoded within a 32-bit integer."
::= { gmplsTunnelARHopEntry 2 }
gmplsTunnelARHopExpLabelPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the gmplsTunnelARHopLabelStatuses object indicates
that a forward label is present, this object contains
a pointer to a row in another MIB table (such as the
gmplsLabelTable) that contains the label in use on
this hop in the forward direction.
If the gmplsTunnelARHopLabelStatuses object indicates that
a forward label is present and this object contains the
value zeroDotZero, then the label in use on this hop is
found in the gmplsTunnelARHopExpLabel object."
::= { gmplsTunnelARHopEntry 3 }
Nadeau and Farrel (Editors) [Page 26]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
gmplsTunnelARHopExpRvrsLabel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the gmplsTunnelARHopLabelStatuses object indicates
that a reverse label is present and
gmplsTunnelARHopExpRvrsLabelPtr contains the value
zeroDotZero, then the label in use on this hop is
found in this object encoded as a 32-bit integer."
::= { gmplsTunnelARHopEntry 4 }
gmplsTunnelARHopExpRvrsLabelPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the gmplsTunnelARHopLabelStatuses object indicates
that a reverse label is present, this object contains
a pointer to a row in another MIB table (such as the
gmplsLabelTable) that contains the label in use on
this hop in the reverse direction.
If the gmplsTunnelARHopLabelStatuses object indicates that
a reverse label is present and this object contains the
value zeroDotZero, then the label in use on this hop is
found in the gmplsTunnelARHopExpRvrsLabel object."
::= { gmplsTunnelARHopEntry 5 }
gmplsTunnelARHopProtection OBJECT-TYPE
SYNTAX BITS {
localAvailable (0),
localInUse (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Availability and usage of protection on the reported link.
localAvailable
Indicates that the link downstream of this node
is protected via a local repair mechanism.
localInUse
Indicates that a local repair mechanism is in use to
maintain this tunnel (usually in the face of an outage
of the link it was previously routed over)."
::= { gmplsTunnelARHopEntry 6 }
-- End of mplsTunnelARHopTable
Nadeau and Farrel (Editors) [Page 27]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
-- Tunnel Computed Hop table.
gmplsTunnelCHopTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsTunnelCHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The gmplsTunnelCHopTable 'extends' the mplsTunnelCHopTable.
It is used to indicate additional information about the
hops of a GMPLS tunnel defined in mplsTunnelTable and
gmplsTunnelTable, as computed by a constraint-based
routing protocol, based on the mplsTunnelHopTable
and the gmplsTunnelHopTable.
Each row in this table is indexed by the same indexes as
mplsTunnelCHopTable. It is acceptable for some rows in
mplsTunnelCHopTable to have corresponding entries in this
table and some to have no corresponding entry in this table.
Please note that since the information necessary to
build entries within this table may not be supported
by some LSRs, implementation of this table is optional.
Furthermore, since the information in this table is actually
provided by a path computation component after the path has
been computed, the entries in this table are provided only
for observation, and hence, all objects in this table are
accessible exclusively as read-only."
REFERENCE
"Generalized MPLS Signaling - RSVP-TE Extensions, Berger,
L. (Editor), RFC 3473, January 2003."
::= { gmplsTeObjects 4 }
gmplsTunnelCHopEntry OBJECT-TYPE
SYNTAX GmplsTunnelCHopEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents additions to a
computed tunnel hop visible in mplsTunnelCHopEntry.
An entry is created by a path computation component
based on the hops specified in the corresponding
mplsTunnelHopTable and gmplsTunnelHopTable.
At a transit LSR this table (if the table is
supported) MAY contain the path computed by path
computation engine on (or on behalf of) the transit LSR."
Nadeau and Farrel (Editors) [Page 28]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
INDEX {
mplsTunnelCHopListIndex,
mplsTunnelCHopIndex
}
::= { gmplsTunnelCHopTable 1 }
GmplsTunnelCHopEntry ::= SEQUENCE {
gmplsTunnelCHopLabelStatuses BITS,
gmplsTunnelCHopExpLabel Unsigned32,
gmplsTunnelCHopExpLabelPtr RowPointer,
gmplsTunnelCHopExpRvrsLabel Unsigned32,
gmplsTunnelCHopExpRvrsLabelPtr RowPointer
}
gmplsTunnelCHopLabelStatuses OBJECT-TYPE
SYNTAX BITS {
forwardPresent (0),
reversePresent (1)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This bitmask indicates the presence of labels indicated by the
gmplsTunnelCHopExpLabel or gmplsTunnelCHopExpLabelPtr and
gmplsTunnelCHopExpRvrsLabel or gmplsTunnelCHopExpRvrsLabelPtr
objects.
A set bit indicates that a label is present for this hop in
the route thus allowing zero to be a valid label value."
::= { gmplsTunnelCHopEntry 1 }
gmplsTunnelCHopExpLabel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the gmplsTunnelCHopLabelStatuses object indicates
that a forward label is present and
gmplsTunnelCHopExpLabelPtr contains the value
zeroDotZero, then the label to use on this hop is
found in this object encoded within a 32-bit integer."
::= { gmplsTunnelCHopEntry 2 }
gmplsTunnelCHopExpLabelPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the gmplsTunnelCHopLabelStatuses object indicates
that a forward label is present, this object contains
a pointer to a row in another MIB table (such as the
Nadeau and Farrel (Editors) [Page 29]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
gmplsLabelTable) that contains the label to use on
this hop in the forward direction.
If the gmplsTunnelCHopLabelStatuses object indicates that
a forward label is present and this object contains the
value zeroDotZero, then the label to use on this hop is
found in the gmplsTunnelCHopExpLabel object."
::= { gmplsTunnelCHopEntry 3 }
gmplsTunnelCHopExpRvrsLabel OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the gmplsTunnelCHopLabelStatuses object indicates
that a reverse label is present and
gmplsTunnelCHopExpRvrsLabelPtr contains the value
zeroDotZero, then the label to use on this hop is
found in this object encoded as a 32-bit integer."
::= { gmplsTunnelCHopEntry 4 }
gmplsTunnelCHopExpRvrsLabelPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the gmplsTunnelCHopLabelStatuses object indicates
that a reverse label is present, this object contains
a pointer to a row in another MIB table (such as the
gmplsLabelTable) that contains the label to use on
this hop in the reverse direction.
If the gmplsTunnelCHopLabelStatuses object indicates that
a reverse label is present and this object contains the
value zeroDotZero, then the label to use on this hop is
found in the gmplsTunnelCHopExpRvrsLabel object."
::= { gmplsTunnelCHopEntry 5 }
-- End of gmplsTunnelCHopTable
-- GMPLS Tunnel Reverse Direction Performance Table.
gmplsTunnelReversePerfTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsTunnelReversePerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table 'augments' the gmplsTunnelTable to provides
per-tunnel packet performance information for the
reverse direction of a bidirectional tunnel. It can be
seen as supplementing the mplsTunnelPerfTable which
augments the mplsTunnelTable."
Nadeau and Farrel (Editors) [Page 30]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
REFERENCE
"Multiprotocol Label Switching (MPLS) Traffic Engineering (TE)
Management Information Base (MIB), Srinivasan, C., Viswanathan,
A., Nadeau, T., RFC 3812, June 2004."
::= { gmplsTeObjects 5 }
gmplsTunnelReversePerfEntry OBJECT-TYPE
SYNTAX GmplsTunnelReversePerfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created by the LSR for every
bidirectional GMPLS tunnel where packets are visible to
the LSR."
AUGMENTS { gmplsTunnelEntry }
::= { gmplsTunnelReversePerfTable 1 }
GmplsTunnelReversePerfEntry ::= SEQUENCE {
gmplsTunnelReversePerfPackets Counter32,
gmplsTunnelReversePerfHCPackets Counter64,
gmplsTunnelReversePerfErrors Counter32,
gmplsTunnelReversePerfBytes Counter32,
gmplsTunnelReversePerfHCBytes Counter64
}
gmplsTunnelReversePerfPackets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of packets forwarded on the tunnel in the
reverse direction if it is bidirectional."
::= { gmplsTunnelReversePerfEntry 1 }
gmplsTunnelReversePerfHCPackets OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for number of packets forwarded on
the tunnel in the reverse direction if it is bidirectional."
::= { gmplsTunnelReversePerfEntry 2 }
gmplsTunnelReversePerfErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Nadeau and Farrel (Editors) [Page 31]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
DESCRIPTION
"Number of errored packets received on the tunnel in
the reverse direction if it is bidirectional."
::= { gmplsTunnelReversePerfEntry 3 }
gmplsTunnelReversePerfBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of bytes forwarded on the tunnel in the
reverse direction if it is bidirectional."
::= { gmplsTunnelReversePerfEntry 4 }
gmplsTunnelReversePerfHCBytes OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"High capacity counter for number of bytes forwarded
on the tunnel in the reverse direction if it is
bidirectional."
::= { gmplsTunnelReversePerfEntry 5 }
-- End of gmplsTunnelReversePerfTable
-- GMPLS Tunnel Error Table.
gmplsTunnelErrorTable OBJECT-TYPE
SYNTAX SEQUENCE OF GmplsTunnelErrorEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table 'augments' the mplsTunnelTable
This table provides per-tunnel information about
errors. Errors may be detected locally or reported
through the signaling protocol.
Error reporting is not exclusive to GMPLS and this
table may be applied in MPLS systems."
REFERENCE
"Multiprotocol Label Switching (MPLS) Traffic Engineering (TE)
Management Information Base (MIB), Srinivasan, C., Viswanathan,
A., Nadeau, T., RFC 3812, June 2004."
::= { gmplsTeObjects 6 }
gmplsTunnelErrorEntry OBJECT-TYPE
SYNTAX GmplsTunnelErrorEntry
MAX-ACCESS not-accessible
STATUS current
Nadeau and Farrel (Editors) [Page 32]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
DESCRIPTION
"An entry in this table is created by the LSR for
every tunnel where error information is visible to
the LSR.
Note that systems which read the objects in this table
one at a time may experience a discontinuity as the
result of a new error occurring in between object reads.
Systems that are vulnerable to this should read
gmplsTunnelErrorLastTime before and after reading the
other objects."
AUGMENTS { mplsTunnelEntry }
::= { gmplsTunnelErrorTable 1 }
GmplsTunnelErrorEntry ::= SEQUENCE {
gmplsTunnelErrorLastErrorType INTEGER,
gmplsTunnelErrorLastTime TimeStamp,
gmplsTunnelErrorReporterType InetAddressType,
gmplsTunnelErrorReporter InetAddress,
gmplsTunnelErrorCode Unsigned32,
gmplsTunnelErrorSubcode Unsigned32,
gmplsTunnelErrorTLVs OCTET STRING,
gmplsTunnelErrorHelpString DisplayString
}
gmplsTunnelErrorLastErrorType OBJECT-TYPE
SYNTAX INTEGER {
noError (0),
unknown (1),
protocol (2),
pathComputation (3),
localConfiguration (4),
localResources (5),
localOther (6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The nature of the last error. Provides interpretation
context for gmplsTunnelErrorProtocolCode and
gmplsTunnelErrorProtocolSubcode.
A value of noError (0) shows that there is no error
associated with this tunnel and means that the other
objects in this table entry have no meaning.
A value of unknown (1) shows that there is an error
but that no additional information about the cause is
known. The error may have been received in a signaled
message or generated locally.
Nadeau and Farrel (Editors) [Page 33]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
A value of protocol (2) or pathComputation (3) indicates
that the cause of an error and identifies an error that
has been received through signaling or will itself be
signaled.
A value of localConfiguration (4), localResources (5) or
localOther (6) identifies an error which has been detected
by the local node, but which will not be reported through
signaling."
::= { gmplsTunnelErrorEntry 1 }
gmplsTunnelErrorLastTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time at which the last error occurred. This is
presented as the value of SysUpTime when the error
occurred or was reported to this node.
If gmplsTunnelErrorLastErrorType has the value
noError (0), then this object is ignored."
::= { gmplsTunnelErrorEntry 2 }
gmplsTunnelErrorReporterType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address type of the error reported.
This object is used to aid in interpretation of
gmplsTunnelErrorReporter."
::= { gmplsTunnelErrorEntry 3 }
gmplsTunnelErrorReporter OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address of the node reporting the last error, or
the address of the resource (such as an interface)
associated with the error.
If gmplsTunnelErrorLastErrorType has the value
noError (0), then this object is ignored.
If gmplsTunnelErrorLastErrorType has the value
unknown (1), localConfiguration (4), localResources (5),
or localOther (6) this object MAY contain a zero value.
Nadeau and Farrel (Editors) [Page 34]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
This object should be interpreted in the context of
the value of the object gmplsTunnelErrorReporterType."
REFERENCE
"RFC3291, Textual Conventions for Internet Network
Addresses, Section 4. Usage Hints."
::= { gmplsTunnelErrorEntry 4 }
gmplsTunnelErrorCode OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The primary error code associated with the last error.
The interpretation of this error code depends on the
value of gmplsTunnelErrorLastErrorType. If the value
of gmplsTunnelErrorLastErrorType is noError (0) the
value of this object should be 0 and should be
ignored. If the value of gmplsTunnelErrorLastErrorType
is protocol (2) the error should be interpreted in the
context of the signling protocol identified by the
mplsTunnelSignallingProto object.
Values in excess 32767 of are not used by signaling
protocols and may safely be used as
implementation-specific error codes."
REFERENCE
"1. Braden, R. (Ed.) et al., Resource ReserVation Protocol --
Version 1 Functional Specification, RFC 2205, September 1997.
2. RSVP-TE: Extensions to RSVP for LSP Tunnels, Awduche
et al, RFC 3209, December 2001.
3. Generalized MPLS Signaling - RSVP-TE Extensions, Berger,
L. (Editor), RFC 3473, January 2003."
::= { gmplsTunnelErrorEntry 5 }
gmplsTunnelErrorSubcode OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The secondary error code associated with the last error and the
protocol used to signal this tunnel. This value is interpreted
in the context of the value of gmplsTunnelErrorCode.
If the value of gmplsTunnelErrorLastErrorType is
noError (0) the value of this object should be 0 and
should be ignored."
REFERENCE
"1. Braden, R. (Ed.) et al., Resource ReserVation Protocol --
Version 1 Functional Specification, RFC 2205, September 1997.
Nadeau and Farrel (Editors) [Page 35]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
2. RSVP-TE: Extensions to RSVP for LSP Tunnels, Awduche
et al, RFC 3209, December 2001.
3. Generalized MPLS Signaling - RSVP-TE Extensions, Berger,
L. (Editor), RFC 3473, January 2003."
::= { gmplsTunnelErrorEntry 6 }
gmplsTunnelErrorTLVs OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence of interface identifier TLVs reported
with the error by the protocol code. The interpretation
of the TLVs and the encoding within the protocol are
described in the references.
A value of zero in the first octet indicates that no
TLVs are present."
REFERENCE
"Generalized MPLS Signaling - RSVP-TE Extensions, Berger,
L. (Editor), RFC 3473, January 2003."
::= { gmplsTunnelErrorEntry 7 }
gmplsTunnelErrorHelpString OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A textual string containing information about the
last error, recovery actions and support advice. If
there is no help string this object contains a zero
length string.
If the value of gmplsTunnelErrorLastErrorType is
noError (0) this object should contain a zero length
string, but may contain a help string indicating
that there is no error."
::= { gmplsTunnelErrorEntry 8 }
-- GMPLS Notifications.
gmplsTunnelDown NOTIFICATION-TYPE
OBJECTS {
mplsTunnelAdminStatus,
mplsTunnelOperStatus,
gmplsTunnelErrorLastErrorType,
gmplsTunnelErrorReporterType,
gmplsTunnelErrorReporter,
gmplsTunnelErrorCode,
gmplsTunnelErrorSubcode
}
STATUS current
Nadeau and Farrel (Editors) [Page 36]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
DESCRIPTION
"This notification is generated when a
mplsTunnelOperStatus object for one of the
configured tunnels is about to enter the down state
from some other state (but not from the notPresent
state). This other state is indicated by the
included value of mplsTunnelOperStatus.
The objects in this notification provide additional
error information that indicates the reason why the
tunnel has transitioned down.
Note that an implementation SHOULD only issue one of
mplsTunnelDown and gmplsTunnelDown for a single event
on a single tunnel."
::= { gmplsTeNotifications 1 }
-- End of notifications.
-- Module compliance.
gmplsTeGroups
OBJECT IDENTIFIER ::= { gmplsTeConformance 1 }
gmplsTeCompliances
OBJECT IDENTIFIER ::= { gmplsTeConformance 2 }
-- Compliance requirement for fully compliant implementations.
-- The mandatory group has to be implemented by all
-- LSRs that originate, terminate or act as transit for
-- TE-LSPs/tunnels.
-- In addition, depending on the type of tunnels
-- supported, other groups become mandatory as
-- explained below.
gmplsTeModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION "Compliance statement for agents that provide full
support for GMPLS-TE-STD-MIB. Such devices can
then be monitored and also be configured using
this MIB module."
MODULE -- this module
MANDATORY-GROUPS {
gmplsTunnelGroup,
gmplsTunnelScalarGroup,
gmplsTunnelSignaledGroup
}
::= { gmplsTeCompliances 1 }
Nadeau and Farrel (Editors) [Page 37]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
-- Compliance requirement for read-only compliant implementations.
gmplsTeModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"Compliance requirement for implementations that only
provide read-only support for GMPLS-TE-STD-MIB.
Such devices can then be monitored but cannot be
configured using this MIB module."
MODULE -- this module
-- The mandatory group has to be implemented by all
-- LSRs that originate, terminate or act as transit for
-- TE-LSPs/tunnels.
-- In addition, depending on the type of tunnels
-- supported, other groups become mandatory as
-- explained below.
MANDATORY-GROUPS {
gmplsTunnelGroup,
gmplsTunnelScalarGroup
}
GROUP gmplsTunnelSignaledGroup
DESCRIPTION
"This group is mandatory for devices which support
signaled tunnel set up, in addition to
gmplsTunnelGroup. The following constraints apply:
mplsTunnelSignallingProto should be at least
read-only returning a value of ldp(2), or rsvp(3)."
GROUP gmplsTunnelIsNotIntfcGroup
DESCRIPTION
"This group is mandatory for devices which support
tunnels that are not interfaces, in addition to
gmplsTunnelGroup. The following constraints apply:
gmplsTunnelIsIf must at least be read-only returning no(0)."
GROUP gmplsTunnelIsIntfcGroup
DESCRIPTION
"This group is mandatory for devices which support
tunnels that are interfaces, in addition to gmplsTunnelGroup."
GROUP gmplsTunnelOptionalGroup
DESCRIPTION
"Objects in this group are optional."
Nadeau and Farrel (Editors) [Page 38]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
GROUP gmplsTeNotificationGroup
DESCRIPTION "This group is mandatory for those implementations
which can implement the notifications contained
in this group."
-- GMPLS Tunnel scalars.
-- All scalars have max access read-only
-- gmplsTunnelTable
OBJECT gmplsTunnelAttributes
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelLSPEncoding
SYNTAX Integer32
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelSwitchingType
SYNTAX Integer32
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelLinkProtection
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelGPid
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelSecondary
SYNTAX TruthValue
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelDirection
SYNTAX INTEGER {
forward (0),
bidirectional (1)
}
MIN-ACCESS read-only
Nadeau and Farrel (Editors) [Page 39]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
DESCRIPTION
"Only forward (0) is required."
OBJECT gmplsTunnelPathComp
SYNTAX INTEGER {
dynamicFull(1), -- CSPF fully computed
explicit(2), -- fully
dynamicPartial(3) -- CSPF partially computed
}
MIN-ACCESS read-only
DESCRIPTION
"Only explicit (2) is required."
OBJECT gmplsTunnelUpNotRecip
SYNTAX IpAddress
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelDownNotRecip
SYNTAX IpAddress
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelAdminStatusFlags
SYNTAX BITS {
delInProgress (0),
adminDown (1),
testing (2),
reflect (31)
}
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelExtraParamsPtr
SYNTAX RowPointer
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
-- gmplsTunnelHopTable
-- gmplsTunnelHopLabelStatuses has max access read-only
Nadeau and Farrel (Editors) [Page 40]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
OBJECT gmplsTunnelHopExpLabel
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelHopExpLabelPtr
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelHopExpRvrsLabel
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT gmplsTunnelHopExpRvrsLabelPtr
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
-- gmplsTunnelARHopTable
-- all objects have max access read-only
-- glmpsTunnelCHopTable
-- all objects have max access read-only
-- gmplsTunnelReversePerfTable
-- all objects have max access read-only
-- gmplsTunnelErrorTable
-- all objects have max access read-only
::= { gmplsTeCompliances 2 }
-- Units of conformance.
gmplsTunnelGroup OBJECT-GROUP
OBJECTS {
gmplsTunnelDirection,
gmplsTunnelReversePerfPackets,
gmplsTunnelReversePerfHCPackets,
gmplsTunnelReversePerfErrors,
gmplsTunnelReversePerfBytes,
gmplsTunnelReversePerfHCBytes,
gmplsTunnelErrorLastErrorType,
gmplsTunnelErrorLastTime,
gmplsTunnelErrorReporterType,
gmplsTunnelErrorReporter,
gmplsTunnelErrorCode,
gmplsTunnelErrorSubcode,
gmplsTunnelErrorTLVs,
Nadeau and Farrel (Editors) [Page 41]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
gmplsTunnelErrorHelpString
}
STATUS current
DESCRIPTION
"Necessary, but not sufficient, set of objects to implement
tunnels. In addition, depending on the type of the tunnels
supported (for example, manually configured or signaled,
persistent or non-persistent, etc.), the following other
groups defined below are mandatory:
gmplsTunnelSignaledGroup, gmplsTunnelIsNotIntfcGroup
and/or gmplsTunnelIsIntfcGroup."
::= { gmplsTeGroups 1 }
gmplsTunnelSignaledGroup OBJECT-GROUP
OBJECTS {
gmplsTunnelAttributes,
gmplsTunnelLSPEncoding,
gmplsTunnelSwitchingType,
gmplsTunnelLinkProtection,
gmplsTunnelGPid,
gmplsTunnelSecondary,
gmplsTunnelPathComp,
gmplsTunnelUpNotRecip,
gmplsTunnelDownNotRecip,
gmplsTunnelAdminStatusFlags,
gmplsTunnelHopLabelStatuses,
gmplsTunnelHopExpLabel,
gmplsTunnelHopExpLabelPtr,
gmplsTunnelHopExpRvrsLabel,
gmplsTunnelHopExpRvrsLabelPtr
}
STATUS current
DESCRIPTION
"Objects needed to implement signaled tunnels."
::= { gmplsTeGroups 3 }
gmplsTunnelScalarGroup OBJECT-GROUP
OBJECTS {
gmplsTunnelsConfigured,
gmplsTunnelsActive
}
STATUS current
DESCRIPTION
"Scalar objects needed to implement MPLS tunnels."
::= { gmplsTeGroups 4 }
gmplsTunnelIsIntfcGroup OBJECT-GROUP
OBJECTS {
gmplsTunnelUnnumIf
}
Nadeau and Farrel (Editors) [Page 42]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
STATUS current
DESCRIPTION
"Objects needed to implement tunnels that are
interfaces."
::= { gmplsTeGroups 5 }
gmplsTunnelIsNotIntfcGroup OBJECT-GROUP
OBJECTS {
gmplsTunnelUnnumIf
}
STATUS current
DESCRIPTION
"Objects needed to implement tunnels that are not
interfaces."
::= { gmplsTeGroups 6 }
gmplsTunnelOptionalGroup OBJECT-GROUP
OBJECTS {
gmplsTunnelExtraParamsPtr,
gmplsTunnelARHopLabelStatuses,
gmplsTunnelARHopExpLabel,
gmplsTunnelARHopExpLabelPtr,
gmplsTunnelARHopExpRvrsLabel,
gmplsTunnelARHopExpRvrsLabelPtr,
gmplsTunnelARHopProtection,
gmplsTunnelCHopLabelStatuses,
gmplsTunnelCHopExpLabel,
gmplsTunnelCHopExpLabelPtr,
gmplsTunnelCHopExpRvrsLabel,
gmplsTunnelCHopExpRvrsLabelPtr
}
STATUS current
DESCRIPTION
"The objects in this group are optional."
::= { gmplsTeGroups 7 }
gmplsTeNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
gmplsTunnelDown
}
STATUS current
DESCRIPTION
"Set of notifications implemented in this module.
None is mandatory."
::= { gmplsTeGroups 8 }
END
Nadeau and Farrel (Editors) [Page 43]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
9. Security Considerations
It is clear that the MIB modules described in this document in
association with the MPLS-TE-STD-MIB are potentially useful for
monitoring of MPLS and GMPLS tunnels. These MIB modules can also be
used for configuration of certain objects, and anything that can be
configured can be incorrectly configured, with potentially disastrous
results.
There are a number of management objects defined in these MIB modules
with a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations. These are the tables and objects and their
sensitivity/vulnerability:
o the gmplsTunnelTable and gmplsTunnelHopTable collectively contain
objects to provision GMPLS tunnels interfaces at their ingress
LSRs. Unauthorized write access to objects in these tables, could
result in disruption of traffic on the network. This is especially
true if a tunnel has already been established. The use of stronger
mechanisms such as SNMPv3 security should be considered where
possible. Specifically, SNMPv3 VACM and USM MUST be used with any
SNMPv3 agent which implements these MIB modules.
Some of the readable objects in these MIB modules "i.e., objects with
a MAX-ACCESS other than not-accessible" may be considered sensitive
or vulnerable in some network environments. It is thus important to
control even GET and/or NOTIFY access to these objects and possibly
to even encrypt the values of these objects when sending them over
the network via SNMP. These are the tables and objects and their
sensitivity/vulnerability:
o the gmplsTunnelTable, gmplsTunnelHopTable, gmplsTunnelARHopTable,
gmplsTunnelCHopTable, gmplsTunnelReversePerfTable,
gmplsTunnelErrorTable collectively show the tunnel network
topology and status. If an Administrator does not want to reveal
this information, then these tables should be considered
sensitive/vulnerable.
SNMP versions prior to SNMPv3 did not include adequate security. Even
if the network itself is secure "for example by using IPSec", even
then, there is no control as to who on the secure network is allowed
to access and GET/SET "read/change/create/delete" the objects in
these MIB modules. It is RECOMMENDED that implementers consider the
security features as provided by the SNMPv3 framework "see [RFC3410],
section 8", including full support for the SNMPv3 cryptographic
mechanisms "for authentication and privacy".
Nadeau and Farrel (Editors) [Page 44]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
Further, deployment of SNMP versions prior to SNMPv3 is NOT
RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to
enable cryptographic security. It is then a customer/operator
responsibility to ensure that the SNMP entity giving access to an
instance of this MIB module, is properly configured to give access to
the objects only to those principals "users" that have legitimate
rights to indeed GET or SET "change/create/delete" them.
10. Acknowledgments
This draft is the work of the five authors listed in the Authors'
Addresses section.
This document extends [RFC3812]. The authors would like to express
their gratitude to all those who worked on that earlier MIB document.
Thanks also to Tony Zinicola and Jeremy Crossen for their valuable
contributions during an early implementation, and to Baktha
Muralidharan for his review.
Special thanks to Joan Cucchiara and Len Nieman for their help with
compilation issues.
11. IANA Considerations
As requested in the GMPLS-TC-STD-MIB [GMPLSTCMIB], GMPLS related
standards track MIB modules should be rooted under the mplsStdMIB
subtree. There is one GMPLS MIB Module contained in this document,
and the following "IANA Considerations" subsection requests IANA for
a new assignment under the mplsStdMIB subtree. New assignments can
only be made via a Standards Action as specified in [RFC2434].
11.1. IANA Considerations for GMPLS-TE-STD-MIB
IANA is requested to assign an OID to the GMPLS-TE-STD-MIB module
specified in this document as { mplsStdMIB xx }.
12. References
12.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M., and S. Waldbusser, "Structure
of Management Information Version 2 (SMIv2)", STD
58, RFC 2578, April 1999.
Nadeau and Farrel (Editors) [Page 45]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M., and S. Waldbusser, "Textual
Conventions for SMIv2", STD 58, RFC 2579, April
1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J.,
Case, J., Rose, M., and S. Waldbusser, "Conformance
Statements for SMIv2", STD 58, RFC 2580, April
1999.
[RFC3031] Rosen, E., Viswanathan, A., and R. Callon,
"Multiprotocol Label Switching Architecture", RFC
3031, January 2001.
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T.,
Srinivasan, V., and G. Swallow, "RSVP-TE:
Extensions to RSVP for LSP Tunnels", RFC 3209,
December 2001.
[RFC3212] Jamoussi, B., Aboul-Magd, O., Andersson, L.,
Ashwood-Smith, P., Hellstrand, F., Sundell, K.,
Callon, R., Dantu, R., Wu, L., Doolan, P., Worster,
T., Feldman, N., Fredette, A., Girish, M., Gray,
E., Halpern, J., Heinanen, J., Kilty, T., Malis,
A., and P. Vaananen, "Constraint-Based LSP Setup
using LDP", RFC 3212, December 2001.
[RFC3291] Daniele, M., Haberman, B., Routhier, S.,
Schoenwaelder, J., and Braunschweig, TU, "Textual
Conventions for Internet Network Addresses",
RFC3291, May 2002
[RFC3471] Berger, L. (Editor), "Generalized Multi-Protocol
Label Switching (GMPLS) Signaling Functional
Description", RFC 3471, January 2003.
[RFC3472] Ashwood-Smith, P., Berger, L. (Editors),
"Generalized MPLS Signaling - CR-LDP Extensions",
RFC 3472, January 2003.
[RFC3473] Berger, L. (Editor), "Generalized MPLS Signaling -
RSVP-TE Extensions", RFC 3473, January 2003.
[RFC3477] Kompella, K. and Rekhter, Y., "Signalling Unnumbered
Links in RSVP-TE", RFC 3477, January 2003.
[RFC3480] Kompella, K., Rekhter, Y. and Kullberg, A.,
"Signalling Unnumbered Links in CR-LDP", RFC 3480,
February 2003.
Nadeau and Farrel (Editors) [Page 46]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
[RFC3811] Nadeau, T. and J. Cucchiara, "Definition of Textual
Conventions and for Multiprotocol Label Switching
(MPLS) Management", RFC 3811, June 2004.
[RFC3812] Srinivasan, C., Viswanathan, A., and T. Nadeau,
"Multiprotocol Label Switching (MPLS) Traffic
Engineering (TE) Management Information Base (MIB)",
RFC 3812, June 2004.
[RFC3813] Srinivasan, C., Viswanathan, A., and T. Nadeau,
"Multiprotocol Label Switching (MPLS) Label
Switching (LSR) Router Management Information Base
(MIB)", RFC 3813, June 2004.
[RFC3945] Mannie, E. (Editor), "Generalized Multiprotocol
Label Switching (GMPLS) Architecture", RFC 3945,
October 2004.
[GMPLSLSRMIB] Nadeau, T., Farrel, A., (Editors) "Generalized
Multiprotocol Label Switching (GMPLS) Label
Switching Router (LSR) Management Information
Base", draft-ietf-ccamp-gmpls-lsr-mib-07.txt,
February 2005, work in progress.
[GMPLSOSPF] Kompella, K., et al., "OSPF Extensions in Support
of Generalized MPLS",
draft-ietf-ccamp-ospf-gmpls-extensions-12.txt,
October 2003, work in progress.
[GMPLSTCMIB] Nadeau, T., Farrel, A., (Editors) "Definitions of
Textual Conventions for Multiprotocol Label
Switching (MPLS) Management",
draft-ietf-ccamp-gmpls-te-mib-06.txt, October 2004,
work in progress.
12.2. Informational References
[RFC2026] S. Bradner, "The Internet Standards Process --
Revision 3", RFC 2026, October 1996.
[RFC2434] Narten, T. and H. Alvestrand., "Guidelines for
Writing an IANA Considerations Section in RFCs",
BCP 26, RFC 2434, October 1998.
[RFC3413] Levi, D., Meyer, P., Stewart, B., "SNMP
Applications", RFC 3413, December 2002.
Nadeau and Farrel (Editors) [Page 47]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
[RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart,
"Introduction and Applicability Statements for
Internet-Standard Management Framework", RFC 3410,
December 2002.
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
Architecture for Describing Simple Network
Management Protocol (SNMP) Management Frameworks",
RFC 3411, December 2002.
[GMPLS-G709] D. Papadimitriou (Editor), "Generalized MPLS
Signalling Extensions for G.709 Optical Transport
Networks Control", draft-ietf-ccamp-gmpls-g709-
07.txt, September 2004, work in progress.
13. Authors' Addresses
Thomas D. Nadeau
Cisco Systems, Inc.
300 Apollo Drive
Chelmsford, MA 01824
Phone: +1-978-244-3051
Email: tnadeau@cisco.com
Cheenu Srinivasan
Bloomberg L.P.
499 Park Ave.,
New York, NY 10022
Phone: +1-212-893-3682
Email: cheenu@bloomberg.net
Adrian Farrel
Old Dog Consulting
Phone: +44-(0)-1978-860944
Email: adrian@olddog.co.uk
Tim Hall
Data Connection Ltd.
100 Church Street
Enfield, Middlesex
EN2 6BQ, UK
Phone: +44 20 8366 1177
Email: tim.hall@dataconnection.com
Nadeau and Farrel (Editors) [Page 48]
Internet Draft draft-ietf-ccamp-gmpls-te-mib-08.txt February 2005
Ed Harrison
Data Connection Ltd.
100 Church Street
Enfield, Middlesex
EN2 6BQ, UK
Phone: +44 20 8366 1177
Email: ed.harrison@dataconnection.com
14. Intellectual Property Considerations
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
15. Full Copyright Statement
Copyright (C) The Internet Society (2004). This document is subject
to the rights, licenses and restrictions contained in BCP 78, and
except as set forth therein, the authors retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Nadeau and Farrel (Editors) [Page 49]
Html markup produced by rfcmarkup 1.129b, available from
https://tools.ietf.org/tools/rfcmarkup/