[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: (draft-long-ccamp-rsvp-te-bandwidth-availability) 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14

Network Working Group                                    H. Long, M. Ye
Internet Draft                             Huawei Technologies Co., Ltd
Intended status: Standards Track                              G. Mirsky
                                                               Ericsson
                                                         A.D'Alessandro
                                                   Telecom Italia S.p.A
                                                                H. Shah
                                                                  Ciena
Expires: April 13, 2016                                October 16, 2015


         Ethernet Traffic Parameters with Availability Information
           draft-ietf-ccamp-rsvp-te-bandwidth-availability-03.txt


Abstract

   A Packet switching network may contain links with variable bandwidth,
   e.g., copper, radio, etc. The bandwidth of such links is sensitive
   to external environment. Availability is typically used for
   describing the link during network planning. This document
   introduces an Extended Ethernet Bandwidth Profile TLV and an
   optional Availability sub-TLV in Resource ReSerVation Protocol -
   Traffic Engineer (RSVP-TE) signaling. This extension can be used to
   set up a label switching path (LSP) in a Packet Switched Network
   (PSN) that contains links with discretely variable bandwidth.

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six
   months and may be updated, replaced, or obsoleted by other documents
   at any time.  It is inappropriate to use Internet-Drafts as
   reference material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html




Long, et al.             Expires April, 2016                  [Page 1]


Internet-Draft    RSVP-TE - Bandwidth Availability        October 2015


   This Internet-Draft will expire on April 13, 2016.

Copyright Notice

   Copyright (c) 2015 IETF Trust and the persons identified as the
   document authors. All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document. Please review these documents
   carefully, as they describe your rights and restrictions with
   respect to this document. Code Components extracted from this
   document must include Simplified BSD License text as described in
   Section 4.e of the Trust Legal Provisions and are provided without
   warranty as described in the Simplified BSD License.

Table of Contents

   1. Introduction ................................................ 3
   2. Overview .................................................... 4
   3. Extension to RSVP-TE Signaling............................... 4
         3.1.1. Extended Ethernet Bandwidth Profile TLV............ 5
         3.1.2. Availability sub-TLV............................... 5
      3.2. FLOWSPEC Object......................................... 6
      3.3. Signaling Process....................................... 6
   4. Security Considerations...................................... 7
   5. IANA Considerations ......................................... 7
      5.1  Ethernet Sender TSpec TLVs ............................. 7
      5.2  Extended Ethernet Bandwidth Profile TLV ................ 8
   6. References .................................................. 8
      6.1. Normative References.................................... 8
      6.2. Informative References.................................. 9
   7. Appendix: Bandwidth Availability Example..................... 9
   8. Acknowledgments ............................................ 11

Conventions used in this document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC-2119 [RFC2119].

   The following acronyms are used in this draft:

   RSVP-TE  Resource Reservation Protocol-Traffic Engineering

   LSP      Label Switched Path


Long, et al.             Expires April, 2016                  [Page 2]


Internet-Draft    RSVP-TE - Bandwidth Availability        October 2015


   PSN      Packet Switched Network

   SNR      Signal-to-noise Ratio

   TLV      Type Length Value

   LSA      Link State Advertisement

1. Introduction

   The RSVP-TE specification [RFC3209] and GMPLS extensions [RFC3473]
   specify the signaling message including the bandwidth request for
   setting up a label switching path in a PSN network.

   Some data communication technologies allow seamless change of
   maximum physical bandwidth through a set of known discrete values.
   The parameter availability [G.827, F.1703, P.530] is often used to
   describe the link capacity during network planning. The availability
   is a time scale that the requested bandwidth is ensured. A more
   detailed example on the bandwidth availability can be found in
   Appendix A. Assigning different availability classes to different
   types of service over such kind of links provides more efficient
   planning of link capacity. To set up an LSP across these links,
   availability information is required for the nodes to verify
   bandwidth satisfaction and make bandwidth reservation. The
   availability information should be inherited from the availability
   requirements of the services expected to be carried on the LSP. For
   example, voice service usually needs "five nines" availability,
   while non-real time services may adequately perform at four or three
   nines availability. Since different service types may need different
   availabilities guarantees, multiple <availability, bandwidth> pairs
   may be required when signaling.

   If the availability requirement is not specified in the signaling
   message, the bandwidth will be reserved as the highest availability.
   For example, the bandwidth with 99.999% availability of a link is
   100 Mbps; the bandwidth with 99.99% availability is 200 Mbps. When a
   video application requests for 120 Mbps without availability
   requirement, the system will consider the request as 120 Mbps with
   99.999% availability, while the available bandwidth with 99.999%
   availability is only 100 Mbps, therefore the LSP path cannot be set
   up. But in fact, video application doesn't need 99.999% availability;
   99.99% availability is enough. In this case, the LSP could be set up
   if availability is specified in the signaling message.

   To fulfill LSP setup by signaling in these scenarios, this document
   specifies an Extended Ethernet Bandwidth Profile and an Availability


Long, et al.             Expires April, 2016                  [Page 3]


Internet-Draft    RSVP-TE - Bandwidth Availability        October 2015


   sub-TLV. The Availability sub-TLV can be applicable to any kind of
   physical links with variable discrete bandwidth, such as microwave
   or DSL. Multiple Extended Ethernet Bandwidth Profiles with different
   availability can be carried in the Ethernet SENDER_TSPEC object.

2. Overview

   A PSN tunnel may span one or more links in a network. To setup a
   label switching path (LSP), a node may collect link information
   which is spread in routing message, e.g., OSPF TE LSA message, by
   network nodes to get to know about the network topology, and
   calculate out an LSP route based on the network topology, and send
   the calculated LSP route to signaling to initiate a PATH/RESV
   message for setting up the LSP.

   In case that there is(are) link(s) with variable discrete bandwidth
   in a network, a <bandwidth, availability> requirement list should be
   specified for an LSP. Each <bandwidth, availability> pair in the
   list means that listed bandwidth with specified availability is
   required. The list could be inherited from the results of service
   planning for the LSP.

   A node which has link(s) with variable discrete bandwidth attached
   should contain a <bandwidth, availability> information list in its
   OSPF TE LSA messages. The list provides the information that how
   much bandwidth a link can support for a specified availability. This
   information is used for path calculation by the node(s). The routing
   extension for availability can be found in [ARTE].

   When a node initiates a PATH/RESV signaling to set up an LSP, the
   PATH message should carry the <bandwidth, availability> requirement
   list as bandwidth request.  Intermediate node(s) will allocate the
   bandwidth resource for each availability requirement from the
   remaining bandwidth with corresponding availability. An error
   message may be returned if any <bandwidth, availability> request
   cannot be satisfied.

3. Extension to RSVP-TE Signaling

   The initial idea is to define an Availability sub-TLV under Ethernet
   Bandwidth Profile TLV [RFC6003]. However the Ethernet Bandwidth
   Profile TLV doesn't have the ability to carry a sub-TLV according to
   RFC6003. Therefore, an Extend Ethernet Bandwidth Profile TLV is
   defined in this document to avoid the backward compatibility issue.
   The Extended Ethernet Bandwidth Profile TLV includes Ethernet BW TLV
   and has variable length. It MAY include Availability sub-TLV which
   is also defined in this document.


Long, et al.             Expires April, 2016                  [Page 4]


Internet-Draft    RSVP-TE - Bandwidth Availability        October 2015


3.1.1. Extended Ethernet Bandwidth Profile TLV

   The Extended Ethernet Bandwidth Profile TLV is included in the
   Ethernet SENDER_TSPEC, and MAY be included for more than one time.
   The Extended Ethernet Bandwidth Profile TLV has the following format.

   0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |              Type             |          Length               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |Pro|A|         |     Index     |          Reserved             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                              CIR                              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                              CBS                              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                              EIR                              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                              EBS                              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                       sub-TLV(OPTIONAL)                       |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

  Figure 1: A new "AF" filed in Extended Ethernet Bandwidth Profile TLV

   The difference between the Extended Ethernet Bandwidth Profile TLV
   and Ethernet Bandwidth Profile TLV is that a new AF field to
   indicate the sub-TLV is defined in the Extended Ethernet Bandwidth
   Profile TLV. The rest definitions are the same.

   A new filed is defined in this document:

     AF filed (bit 2): Availability Field (AF)

   If the AF filed is set to 1, Availability sub-TLV MUST be included
   in the Extended Ethernet Bandwidth Profile TLV. If the AF field is
   set to value 0, then an Availability sub-TLV SHOULD NOT be included.

3.1.2. Availability sub-TLV

   The Availability sub-TLV has the following format:







Long, et al.             Expires April, 2016                  [Page 5]


Internet-Draft    RSVP-TE - Bandwidth Availability        October 2015


       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |               Type            |               Length          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                          Availability                         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                        Figure 2: Availability sub-TLV

      Type (2 octets): TBD

      Length (2 octets): 4

      Availability (4 octets): a 32-bit floating number describes the
      decimal value of availability requirement for this bandwidth
      request. The value MUST be less than 1.

   As the Extended Ethernet Bandwidth Profile TLV can be carried for
   one or more times in the Ethernet SENDER_TSPEC object, the
   Availability sub-TLV can also be present for one or more times.

3.2. FLOWSPEC Object

   The FLOWSPEC object (Class-Num = 9, Class-Type = TBD) has the same
   format as the Ethernet SENDER_TSPEC object.

3.3. Signaling Process

   The source node initiates PATH messages including one or more
   Extended Bandwidth Profile TLVs with different availability values
   in the SENDER_TSPEC object. Each Extended Bandwidth Profile TLV
   specifies the bandwidth request with referred availability
   requirement.

   The intermediate and destination nodes check whether they can
   satisfy the bandwidth requirements by comparing each bandwidth
   requirement inside the SENDER_TSPEC objects with the remaining link
   sub-bandwidth resource with respective availability guarantee when
   received the PATH message.








Long, et al.             Expires April, 2016                  [Page 6]


Internet-Draft    RSVP-TE - Bandwidth Availability        October 2015


     o   If all <bandwidth, availability> requirements can be
        satisfied (the requested bandwidth under each availability
        parameter is smaller than or equal to the remaining bandwidth
        under the corresponding availability parameter on its local
        link), it SHOULD reserve the bandwidth resource from each
        remaining sub-bandwidth portion on its local link to set up
        this LSP. Optionally, the higher availability bandwidth can be
        allocated to lower availability request when the lower
        availability bandwidth cannot satisfy the request.

     o   If at least one <bandwidth, availability> requirement cannot
        be satisfied, it SHOULD generate PathErr message with the error
        code "Admission Control Error" and the error value "Requested
        Bandwidth Unavailable" (see [RFC2205]).

   If two LSPs request for the bandwidth with the same availability
   requirement, a way to resolve the contention is comparing the node
   ID, the node with the higher node ID will win the contention. More
   details can be found in [RFC3473].

   If a node does not support the Extended Bandwidth Profile TLV and
   Availability sub-TLV, it SHOULD generate PathErr message with the
   error code "Extended Class-Type Error" and the error value "Class-
   Type mismatch" (see [RFC2205]).

4. Security Considerations

   This document does not introduce new security considerations to the
   existing RSVP-TE signaling protocol.

5. IANA Considerations

   IANA maintains registries and sub-registries for RSVP-TE used by
   GMPLS. IANA is requested to make allocations from these registries
   as set out in the following sections.

5.1 Ethernet Sender TSpec TLVs

   IANA maintains a registry of GMPLS parameters called "Generalized
   Multi-Protocol Label Switching (GMPLS) Signaling Parameters".

   IANA has created a new sub-registry called "Ethernet Sender TSpec
   TLVs / Ethernet Flowspec TLVs" to contain the TLV type values for
   TLVs carried in the Ethernet SENDER_TSPEC object. A new value is as
   follow:




Long, et al.             Expires April, 2016                  [Page 7]


Internet-Draft    RSVP-TE - Bandwidth Availability        October 2015


   Type       Description                            Reference

   -----      -----------------------------------    ---------

   TBD        Extended Ethernet Bandwidth Profile    [This ID]

5.2 Extended Ethernet Bandwidth Profile TLV

   IANA has created a new sub-registry called "Extended Ethernet
   Bandwidth Profiles" to contain bit flags carried in the Extended
   Ethernet Bandwidth Profile TLV of the Ethernet SENDER_TSPEC object.

   Bits are to be allocated by Standards Action. Bits are numbered from
   bit 0 as the low order bit. A new bit field is as follow:

   Bit     Hex               Description              Reference

   ---     ----              ------------------       -----------

   0       0x01              Coupling Flag (CF)        [RFC6003]

   1       0x02              Color Mode (CM)           [RFC6003]

   2       0x04              Availability Field (AF)   [This ID]

   Sub-TLV types for Extended Ethernet Bandwidth Profiles are to be
   allocated by Standards Action. Initial values are as follows:

   Type    Length          Format                        Description

   ---     ----            ------------------            -----------

   0        -              Reserved                      Reserved value

   0x01     4              see Section 3.1.2 of this ID  Availability

6. References

6.1. Normative References

   [RFC2210] Wroclawski, J., "The Use of RSVP with IETF Integrated
             Services", RFC 2210, September 1997.

   [RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan,
             V.,and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
             Tunnels", RFC 3209, December 2001.



Long, et al.             Expires April, 2016                  [Page 8]


Internet-Draft    RSVP-TE - Bandwidth Availability        October 2015


   [RFC3473] Berger, L., "Generalized Multi-Protocol Label Switching
             (GMPLS) Signaling Resource ReserVation Protocol-Traffic
             Engineering (RSVP-TE) Extensions", RFC 3473, January 2003.

   [RFC6003] Papadimitriou, D. "Ethernet Traffic Parameters", RFC 6003,
             October 2010.

6.2. Informative References

   [MCOS]    Minei, I., Gan, D., Kompella, K., and X. Li, "Extensions
             for Differentiated Services-aware Traffic Engineered
             LSPs", Work in Progress, June 2006.

   [G.827]  ITU-T Recommendation, "Availability performance parameters
             and objectives for end-to-end international constant bit-
             rate digital paths", September, 2003.

   [F.1703]  ITU-R Recommendation, "Availability objectives for real
             digital fixed wireless links used in 27 500 km
             hypothetical reference paths and connections", January,
             2005.

   [P.530]   ITU-R Recommendation," Propagation data and prediction
             methods required for the design of terrestrial line-of-
             sight systems", February, 2012

   [EN 302 217] ETSI standard, "Fixed Radio Systems; Characteristics
             and requirements for point-to-point equipment and
             antennas", April, 2009

   [ARTE]    H., Long, M., Ye, Mirsky, G., Alessandro, A., Shah, H.,
             "OSPF Routing Extension for Links with Variable Discrete
             Bandwidth", Work in Progress, June, 2015

7. Appendix: Bandwidth Availability Example

   In mobile backhaul network, microwave links are very popular for
   providing connection of last hops. In case of heavy rain, to
   maintain the link connectivity, the microwave link MAY lower the
   modulation level since demodulating the lower modulation level needs
   a lower Signal-to-Noise Ratio (SNR). This is called adaptive
   modulation technology [EN 302 217]. However, a lower modulation
   level also means lower link bandwidth. When link bandwidth is
   reduced because of modulation down-shifting, high-priority traffic
   can be maintained, while lower-priority traffic is dropped.
   Similarly, the copper links MAY change their link bandwidth due to
   external interference.


Long, et al.             Expires April, 2016                  [Page 9]


Internet-Draft    RSVP-TE - Bandwidth Availability        October 2015


   Presuming that a link has three discrete bandwidth levels:

   The link bandwidth under modulation level 1, e.g., QPSK, is 100 Mbps;

   The link bandwidth under modulation level 2, e.g., 16QAM, is 200
   Mbps;

   The link bandwidth under modulation level 3, e.g., 256QAM, is 400
   Mbps.

   In sunny day, the modulation level 3 can be used to achieve 400 Mbps
   link bandwidth.

   A light rain with X mm/h rate triggers the system to change the
   modulation level from level 3 to level 2, with bandwidth changing
   from 400 Mbps to 200 Mbps. The probability of X mm/h rain in the
   local area is 52 minutes in a year. Then the dropped 200 Mbps
   bandwidth has 99.99% availability.

   A heavy rain with Y(Y>X) mm/h rate triggers the system to change the
   modulation level from level 2 to level 1, with bandwidth changing
   from 200 Mbps to 100 Mbps. The probability of Y mm/h rain in the
   local area is 26 minutes in a year. Then the dropped 100 Mbps
   bandwidth has 99.995% availability.

   For the 100M bandwidth of the modulation level 1, only the extreme
   weather condition can cause the whole system unavailable, which only
   happens for 5 minutes in a year. So the 100 Mbps bandwidth of the
   modulation level 1 owns the availability of 99.999%.

   In a word, the maximum bandwidth is 400 Mbps. According to the
   weather condition, the sub-bandwidth and its availability are shown
   as follows:

   Sub-bandwidth(Mbps)    Availability

   ------------------     ------------

   200                    99.99%

   100                    99.995%

   100                    99.999%






Long, et al.             Expires April, 2016                 [Page 10]


Internet-Draft    RSVP-TE - Bandwidth Availability        October 2015


8. Acknowledgments

   The authors would like to thank Khuzema Pithewan, Lou Berger, Yuji
   Tochio, Dieter Beller, and Autumn Liu for their comments on the
   document.



   Authors' Addresses

   Hao Long
   Huawei Technologies Co., Ltd.
   No.1899, Xiyuan Avenue, Hi-tech Western District
   Chengdu 611731, P.R.China

   Phone: +86-18615778750
   Email: longhao@huawei.com


   Min Ye (editor)
   Huawei Technologies Co., Ltd.
   No.1899, Xiyuan Avenue, Hi-tech Western District
   Chengdu 611731, P.R.China

   Email: amy.yemin@huawei.com

   Greg Mirsky (editor)
   Ericsson

   Email: gregory.mirsky@ericsson.com

   Alessandro D'Alessandro
   Telecom Italia S.p.A

   Email: alessandro.dalessandro@telecomitalia.it


   Himanshu Shah
   Ciena Corp.
   3939 North First Street
   San Jose, CA 95134
   US

   Email: hshah@ciena.com





Long, et al.             Expires April, 2016                 [Page 11]


Html markup produced by rfcmarkup 1.129b, available from https://tools.ietf.org/tools/rfcmarkup/