[Docs] [txt|pdf|xml] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]
Versions: (draft-raghuvanshi-dhc-dhcpv6-active-leasequery)
00 01 02 03 04 RFC 7653
DHC Working Group D. Raghuvanshi
Internet-Draft K. Kinnear
Updates: 5460 (if approved) D. Kukrety
Intended status: Standards Track Cisco Systems, Inc.
Expires: December 11, 2015 June 9, 2015
DHCPv6 Active Leasequery
draft-ietf-dhc-dhcpv6-active-leasequery-03
Abstract
The Dynamic Host Configuration Protocol for IPv6 (DHCPv6) has been
extended with a Leasequery capability that allows a requestor to
request information about DHCPv6 bindings. That mechanism is limited
to queries for DHCPv6 binding data updates prior to the time the
DHCPv6 server receives the Leasequery request. Continuous update of
an external requestor with Leasequery data is sometimes desired.
This document expands on the DHCPv6 Leasequery protocol, and allows
for active transfer of real-time DHCPv6 binding information data via
TCP. This document also updates DHCPv6 Bulk Leasequery (RFC5460) by
adding new options.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on December 11, 2015.
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
Raghuvanshi, et al. Expires December 11, 2015 [Page 1]
Internet-Draft DHCPv6 Active Leasequery June 2015
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Protocol Overview . . . . . . . . . . . . . . . . . . . . . . 5
4. Interaction Between Active Leasequery and Bulk Leasequery . . 7
5. Extension to DHCPv6 Bulk Leasequery . . . . . . . . . . . . . 8
6. Message and Option Definitions . . . . . . . . . . . . . . . 8
6.1. Message Framing for TCP . . . . . . . . . . . . . . . . . 8
6.2. Messages . . . . . . . . . . . . . . . . . . . . . . . . 8
6.2.1. ACTIVELEASEQUERY . . . . . . . . . . . . . . . . . . 8
6.2.2. STARTTLS . . . . . . . . . . . . . . . . . . . . . . 9
6.2.3. Response Messages . . . . . . . . . . . . . . . . . . 9
6.3. Options . . . . . . . . . . . . . . . . . . . . . . . . . 9
6.3.1. OPTION_LQ_BASE_TIME . . . . . . . . . . . . . . . . . 9
6.3.2. OPTION_LQ_START_TIME . . . . . . . . . . . . . . . . 10
6.3.3. OPTION_LQ_END_TIME . . . . . . . . . . . . . . . . . 11
6.4. Connection and Transmission Parameters . . . . . . . . . 12
7. Information Communicated by Active Leasequery . . . . . . . . 12
8. Requestor Behavior . . . . . . . . . . . . . . . . . . . . . 13
8.1. General Processing . . . . . . . . . . . . . . . . . . . 13
8.2. Initiating a Connection . . . . . . . . . . . . . . . . . 13
8.3. Forming an Active Leasequery . . . . . . . . . . . . . . 14
8.4. Processing Active Replies . . . . . . . . . . . . . . . . 15
8.4.1. Processing Replies from a Request Containing a
OPTION_LQ_START_TIME . . . . . . . . . . . . . . . . 17
8.5. Processing Time Values in Leasequery messages . . . . . . 19
8.6. Examples . . . . . . . . . . . . . . . . . . . . . . . . 20
8.6.1. Query Failure . . . . . . . . . . . . . . . . . . . . 20
8.6.2. Data Missing on Server . . . . . . . . . . . . . . . 20
8.6.3. Successful Query . . . . . . . . . . . . . . . . . . 21
8.7. Closing Connections . . . . . . . . . . . . . . . . . . . 21
9. Server Behavior . . . . . . . . . . . . . . . . . . . . . . . 22
9.1. Accepting Connections . . . . . . . . . . . . . . . . . . 22
9.2. Rejecting Connections . . . . . . . . . . . . . . . . . . 23
9.3. Replying to an Active Leasequery . . . . . . . . . . . . 23
9.4. Multiple or Parallel Queries . . . . . . . . . . . . . . 25
9.5. Closing Connections . . . . . . . . . . . . . . . . . . . 25
10. Security Considerations . . . . . . . . . . . . . . . . . . . 26
11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 26
12. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 27
Raghuvanshi, et al. Expires December 11, 2015 [Page 2]
Internet-Draft DHCPv6 Active Leasequery June 2015
13. Modification History . . . . . . . . . . . . . . . . . . . . 27
14. References . . . . . . . . . . . . . . . . . . . . . . . . . 27
14.1. Normative References . . . . . . . . . . . . . . . . . . 27
14.2. Informative References . . . . . . . . . . . . . . . . . 27
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 28
1. Introduction
The DHCPv6 [RFC3315] protocol specifies a mechanism for the
assignment of IPv6 address and configuration information to IPv6
nodes. IPv6 Prefix Delegation for DHCPv6 (PD) [RFC3633] specifies a
mechanism for DHCPv6 delegation of IPv6 prefixes and related data.
DHCPv6 servers maintain authoritative information including binding
information for delegated IPv6 prefixes.
Requirements exist for external entities to keep up to date on the
correspondence between DHCPv6 clients and their bindings. These
entities need to keep up with the current binding activity of the
DHCPv6 server. Keeping up with these binding activity is termed
"active" leasequery.
The DHCPv6 Bulk Leasequery [RFC5460] capability can be used to
recover useful information from a DHCPv6 server when some external
entity starts up. This entity could be one which is directly
involved in the DHCPv6 client - server transactions (e.g., a relay
agent), or it could be an external process which needs information
present in the DHCPv6 server's lease state database.
The Active Leasequery capability documented here is designed to allow
an entity not directly involved in DHCPv6 client - server
transactions to nevertheless keep current with the state of the
DHCPv6 lease state information in real-time.
This document updates DHCPv6 Bulk Leasequery [RFC5460] by adding new
options, as described in Section 6.2.1. For the DHCPv6 servers,
supporting Bulk Leasequery and not Active Leasequery, Section 9.2
specifies the mechanism to reject incoming Active Leasequery
requests.
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
DHCPv6 terminology is defined in [RFC3315]. Terminology specific to
DHCPv6 Active Leasequery can be found below:
Raghuvanshi, et al. Expires December 11, 2015 [Page 3]
Internet-Draft DHCPv6 Active Leasequery June 2015
o "Absolute Time"
A 32-bit unsigned quantity containing the number of seconds since
midnight (UTC), January 1, 2000, modulo 2^32.
o "Active Leasequery"
Keeping up to date in real-time (or near real-time) with DHCPv6
binding activity.
o "Bulk Leasequery"
Requesting and receiving the information about all or some of the
existing DHCPv6 binding information in an efficient manner, as
defined by [RFC5460].
o "blocked TCP connection"
A TCP connection is considered blocked if the underlying TCP
transport will not accept new messages to be sent without blocking
the thread that is attempting to send the message.
o "binding change/update"
Any change in the DHCPv6 binding state. This also includes
expiration or deletion of the binding.
o "catch-up information"
If a DHCPv6 Active Leasequery requestor sends OPTION_LQ_START_TIME
option in an ACTIVELEASEQUERY message, the DHCPv6 server will
attempt to send the requestor the information that changed since
the time specified in the OPTION_LQ_START_TIME option. The
binding information sent to satisfy this request is the catch-up
information.
Raghuvanshi, et al. Expires December 11, 2015 [Page 4]
Internet-Draft DHCPv6 Active Leasequery June 2015
o "catch-up phase"
The period while catch-up information is being sent is the catch-
up phase.
o "clock skew"
The difference between the absolute time on a DHCPv6 server and
the absolute time on the system where a requestor of an Active or
Bulk Leasequery is executing is termed the "clock skew" for that
Active or Bulk Leasequery connection. It is not absolutely
constant but is likely to vary only slowly. While it is easy to
think that this can be calculated precisely after one message is
received by a requestor from a DHCPv6 server, a more accurate
value is derived from continuously examining the instantaneous
value developed from each message received from a DHCPv6 server
and using it to make small adjustments to the existing value held
in the requestor.
o "DHCPv6 binding state"
Data stored on the DHCPv6 server related to binding.
o "requestor"
The node that sends LEASEQUERY messages to one or more servers to
retrieve information on the bindings for a client.
o "Transaction ID"
An opaque value used to match responses with queries initiated by
an Active Leasequery requestor.
3. Protocol Overview
The Active Leasequery mechanism is modeled on the existing DHCPv6
Bulk Leasequery [RFC5460]; most differences arise from the long term
nature of the TCP [RFC7414] connection required for Active
Leasequery. A DHCPv6 server which supports Active Leasequery MUST
support Bulk Leasequery [RFC5460] as well.
Raghuvanshi, et al. Expires December 11, 2015 [Page 5]
Internet-Draft DHCPv6 Active Leasequery June 2015
An Active Leasequery requestor opens a TCP connection to a DHCPv6
Server, using the DHCPv6 port 547. Note that this implies that the
Leasequery requestor has server IP address(es) available via
configuration or some other means, and that it has unicast IP
reachability to the DHCPv6 server. No relaying for Active Leasequery
is specified.
After establishing a connection, the requestor sends an
ACTIVELEASEQUERY message over the connection. In response, the
server sends updates to the requestor using LEASEQUERY-REPLY and
LEASEQUERY-DATA messages. This response procedure is identical to
[RFC5460], except that in the case of Active Leasequery the server
sends updates whenever some activity occurs to change the binding
state - thus the need for long lived connection.
Active Leasequery has features which allow this external entity to
lose its connection and then reconnect and receive the latest
information concerning any IPv6 bindings changed while it was not
connected.
These features are designed to allow the Active Leasequery requestor
to efficiently become current with respect to the lease state
database after it has been restarted or the machine on which it is
running has been reinitialized. It is easy to define a protocol
which works when the requestor is always connected to the DHCPv6
server. Since that isn't sufficiently robust, much of the mechanism
in this document is designed to deal efficiently with situations that
occur when the Active Leasequery requestor becomes disconnected from
the DHCPv6 server from which it is receiving updates and then
reconnects to that server.
Central to this approach, if the Active Leasequery requestor loses
service, it is allowed to specify the time of its most recent update
in a subsequent Active Leasequery request and the DHCPv6 server will
determine whether or not data was missed while the Active Leasequery
requestor was not connected.
The DHCPv6 server processing the Active Leasequery request may limit
the amount of data saved, and methods exist for the DHCPv6 server to
inform the Active Leasequery requestor that data was missed - not all
could be saved. In this situation, the Active Leasequery requestor
should issue a Bulk Leasequery [RFC5460] to recover information not
available through an Active Leasequery.
DHCPv6 servers are not required to keep any data corresponding to
data missed on an Active Leasequery connection, but will typically
choose to keep data corresponding to some recent activity available
for subsequent queries by a DHCPv6 Active Leasequery requestor whose
Raghuvanshi, et al. Expires December 11, 2015 [Page 6]
Internet-Draft DHCPv6 Active Leasequery June 2015
connection was temporarily interrupted. In other words, DHCPv6
servers supporting catch-up are required to have some mechanism to
keep/save historic information of bindings.
An Active Leasequery requestor would typically use Bulk Leasequery to
initialize its database with all current data when that database
contains no binding information. In addition, it would use Bulk
Leasequery to recover missed information in the event that its
connection with the DHCPv6 server was lost for a longer time than the
DHCPv6 server would keep track of the specific changes to the IPv6
binding information.
The messages sent by the server in response to an Active Leasequery
request should be identical to the messages sent by the server to a
Bulk Leasequery request regarding the way the data is encoded into
the Active Leasequery responses. In addition, the actions taken by
the Active Leasequery requestor to interpret the responses to an
Active Leasequery request should be identical to the way that the
requestor interprets the responses to a Bulk Leasequery request.
Thus, the handling of OPTION_CLIENT_DATA and additional options
discussed in the Bulk Leasequery specification [RFC5460] are to be
followed when implementing Active Leasequery.
4. Interaction Between Active Leasequery and Bulk Leasequery
Active Leasequery is an extension of the Bulk Leasequery protocol
[RFC5460]. The format of messages returned to an Active Leasequery
requestor are identical to that defined for the Bulk Leasequery
protocol [RFC5460].
Applications which employ Active Leasequery to keep a database up to
date with respect to the DHCPv6 server's lease state database should
use an initial Bulk Leasequery to bring their database into
equivalence with that of the DHCPv6 server, and then use Active
Leasequery to keep that database current with respect to the DHCPv6
server's lease state database.
There are several differences between the Active and Bulk Leasequery
protocols. Active Leasequery defines a new message
(ACTIVELEASEQUERY) to send Active Leasequery request to DHCPv6
server. An Active Leasequery connection sends all available updates
to the requestor, based on OPTION_LQ_QUERY option (see
Section 6.2.1).
An Active Leasequery connection does not ever "complete", though the
DHCPv6 server may drop the connection for a variety of reasons
associated with some sort of exception condition.
Raghuvanshi, et al. Expires December 11, 2015 [Page 7]
Internet-Draft DHCPv6 Active Leasequery June 2015
5. Extension to DHCPv6 Bulk Leasequery
This document extends to the capabilities of DHCPv6 Bulk Leasequery
protocol [RFC5460] by defining new options (OPTION_LQ_BASE_TIME,
OPTION_LQ_START_TIME and OPTION_LQ_END_TIME). DHCPv6 server sends
OPTION_LQ_BASE_TIME option in Bulk Leasequery response if requestor
ask for the same in Bulk Leasequery request. OPTION_LQ_START_TIME
and OPTION_LQ_END_TIME can be used in Bulk Leasequery request made to
DHCPv6 server. More details about these options are specified in
Section 6.3.
6. Message and Option Definitions
6.1. Message Framing for TCP
The use of TCP for the Active Leasequery protocol permits one or more
DHCPv6 messages to be sent in response to single Active Leasequery
request. The receiver needs to be able to determine how large each
message is. The same message framing technique used for DHCPv6 Bulk
Leasequery [RFC5460] is used for Active Leasequery as well.
The intent in using the same format is that code which currently
knows how to deal with a message returned from DHCPv6 Bulk Leasequery
[RFC5460] will be able to deal with the message held inside of the
TCP framing.
6.2. Messages
6.2.1. ACTIVELEASEQUERY
The new message type (ACTIVELEASEQUERY) is designed for keeping the
requestor up to date in real-time (or near real-time) with DHCPv6
bindings. It asks the server to return DHCPv6 bindings activity that
occurs subsequent to the receipt of the Active Leasequery request.
An ACTIVELEASEQUERY request MUST contain a transaction-id, and that
transaction-id MUST BE locally unique on the TCP connection on which
it is sent to the DHCPv6 server.
When sending an Active Leasequery request, the requestor MAY include
the OPTION_LQ_START_TIME option in the ACTIVELEASEQUERY request. In
this case, DHCPv6 server returns all the bindings changed on or after
the OPTION_LQ_START_TIME.
If the requestor is interested in receiving all binding updates from
the DHCPv6 server, it MUST NOT include the OPTION_LQ_QUERY option in
the ACTIVELEASEQUERY message. But if the requestor is only
interested in specific binding updates, it MAY include an
Raghuvanshi, et al. Expires December 11, 2015 [Page 8]
Internet-Draft DHCPv6 Active Leasequery June 2015
OPTION_LQ_QUERY option along with a query-types defined in [RFC5007]
and [RFC5460].
Other DHCPv6 options used in the LEASEQUERY message (as specified in
[RFC5460]) can also be used in the ACTIVELEASEQUERY request.
6.2.2. STARTTLS
The new message type (STARTTLS) is designed for establishment of a
TLS connection between requestor and DHCPv6 server.
More details about this message are specified in Section 8.2.
6.2.3. Response Messages
The LEASEQUERY-REPLY message is defined in [RFC5007]. The
LEASEQUERY-DATA and LEASEQUERY-DONE messages are defined in
[RFC5460].
In an Active Leasequery exchange, a single LEASEQUERY-REPLY message
is used to indicate the success or failure of a query, and to carry
data that do not change in the context of a single query and answer,
such as the Server-ID and Client-ID options. If a query is
successful, the DHCPv6 server MUST respond to it with exactly one
LEASEQUERY-REPLY message. If the server is returning binding data,
the LEASEQUERY-REPLY also contains the first client's binding data in
an OPTION_CLIENT_DATA option. Additional binding data is returned
using LEASEQUERY-DATA message as explained in DHCPv6 Bulk Leasequery
[RFC5460]. In case of failure query, single LEASEQUERY-REPLY message
is returned without any binding data.
6.3. Options
New options (OPTION_LQ_BASE_TIME, OPTION_LQ_START_TIME and
OPTION_LQ_END_TIME) are defined as an extension to DHCPv6 Bulk
Leasequery [RFC5460]. The reply messages for Active Leasequery uses
these options along with the options defined in [RFC3315], [RFC5007]
and [RFC5460].
6.3.1. OPTION_LQ_BASE_TIME
The OPTION_LQ_BASE_TIME option is the current time the message was
created to be sent by the DHCPv6 server to the requestor of the
Active or Bulk Leasequery if requestor ask for the same in Active or
Bulk Leasequery request. This MUST be an absolute time (i.e. seconds
since midnight January 1, 2000 UTC). All of the other time based
options in the reply message are relative to this time, including
Raghuvanshi, et al. Expires December 11, 2015 [Page 9]
Internet-Draft DHCPv6 Active Leasequery June 2015
OPTION_CLT_TIME [RFC5007]. This time is in the context of the DHCPv6
server who placed this option in a message.
This is an unsigned integer in network byte order.
The code for this option is TBD.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_LQ_BASE_TIME | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| base-time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code OPTION_LQ_BASE_TIME (TBD).
option-len 4.
base-time DHCPv6 Server Base Time.
6.3.2. OPTION_LQ_START_TIME
The OPTION_LQ_START_TIME option specifies a query start time to the
DHCPv6 server. If specified, only bindings that have changed on or
after the OPTION_LQ_START_TIME should be included in the response to
the query. This option MAY be used in Active or Bulk Leasequery
requests made to a DHCPv6 server.
The requestor MUST determine the OPTION_LQ_START_TIME using lease
information it has received from the DHCPv6 server. This MUST be an
absolute time in the DHCPv6 server's context (see Section 8.5).
Typically (though this is not a requirement) the OPTION_LQ_START_TIME
option will contain the value most recently received in a
OPTION_LQ_BASE_TIME option by the requestor, as this will indicate
the last successful communication with the DHCPv6 server.
This is an unsigned integer in network byte order.
The code for this option is TBD.
Raghuvanshi, et al. Expires December 11, 2015 [Page 10]
Internet-Draft DHCPv6 Active Leasequery June 2015
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_LQ_START_TIME | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| query-start-time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code OPTION_LQ_START_TIME (TBD).
option-len 4.
query-start-time DHCPv6 Server Query Start Time.
6.3.3. OPTION_LQ_END_TIME
The OPTION_LQ_END_TIME option specifies a query end time to the
DHCPv6 server. If specified, only bindings that have changed on or
before the OPTION_LQ_END_TIME should be included in the response to
the query. This option MAY be used in a Bulk Leasequery request.
But it MUST NOT be used in an Active Leasequery request.
The requestor MUST determine the OPTION_LQ_END_TIME based on lease
information it has received from the DHCPv6 server. This MUST be an
absolute time in the context of the DHCPv6 server.
In the absence of information to the contrary, the requestor SHOULD
assume that the time context of the DHCPv6 server is identical to the
time context of the requestor (see Section 8.5).
This is an unsigned integer in network byte order.
The code for this option is TBD.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_LQ_END_TIME | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| query-end-time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code OPTION_LQ_END_TIME (TBD).
option-len 4.
query-end-time DHCPv6 Server Query End Time.
Raghuvanshi, et al. Expires December 11, 2015 [Page 11]
Internet-Draft DHCPv6 Active Leasequery June 2015
6.4. Connection and Transmission Parameters
Active Leasequery uses the same port configuration as DHCPv6 Bulk
Leasequery [RFC5460]. It also uses the other transmission parameters
(BULK_LQ_DATA_TIMEOUT and BULK_LQ_MAX_CONNS) as defined in [RFC5460].
This section presents a table of values used to control Active
Leasequery behavior, including recommended defaults. Implementations
MAY make these values configurable. However, configuring too-small
timeout values may lead to harmful behavior both to this application
as well as to other traffic in the network. As a result, timeout
values smaller than the default values SHOULD NOT be used.
+------------------------+----------+-------------------------------+
| Parameter | Default | Description |
+------------------------+----------+-------------------------------+
| ACTIVE_LQ_RCV_TIMEOUT | 120 secs | Active Leasequery receive |
| | | timeout |
| ACTIVE_LQ_SEND_TIMEOUT | 120 secs | Active Leasequery send |
| | | timeout |
| ACTIVE_LQ_IDLE_TIMEOUT | 60 secs | Active Leasequery idle |
| | | timeout |
+------------------------+----------+-------------------------------+
7. Information Communicated by Active Leasequery
While the information communicated by a DHCPv6 Bulk Leasequery
[RFC5460] is taken directly from the DHCPv6 server's lease state
database, the information communicated by an Active Leasequery is
real-time information. As such, it is the information which is
currently associated with a particular binding in the DHCPv6 server's
lease state database.
This is of significance, because if the Active Leasequery requestor
runs slowly or the requestor disconnects from the DHCPv6 server and
then reconnects with an OPTION_LQ_START_TIME option (signaling a
catch-up operation), the information communicated to the Active
Leasequery requestor is only the most current information from the
DHCPv6 server's lease state database.
The requestor of an Active Leasequery MUST NOT assume that every
lease state change is communicated across an Active Leasequery
connection. Even if the Active Leasequery requestor remains
connected, the DHCPv6 server is only required to transmit information
about a binding that is current when the message is created and
handed off to the TCP stack to send to the requestor.
Raghuvanshi, et al. Expires December 11, 2015 [Page 12]
Internet-Draft DHCPv6 Active Leasequery June 2015
If the TCP connection blocks and the DHCPv6 server is waiting to send
information down the connection, when the connection becomes
available to be written the DHCPv6 server MAY create the message to
send at this time. The current state of the binding will be sent,
and any transition in state or other information that occurred while
the TCP connection was blocked will be lost.
Thus, the Active Leasequery protocol does not allow the requestor to
build a complete history of every activity on every lease. An
effective history of the important state changes for a lease can be
created if the parameters of the DHCPv6 server are tuned to take into
account the requirements of an Active Leasequery requestor. For
instance, the period after the expiration or release of a binding
could be configured long enough (say several minutes, well more than
the receive timeout), so that an Active Leasequery requestor would be
less likely to miss any changes in the binding.
8. Requestor Behavior
8.1. General Processing
A requestor attempts to establish a TCP connection to a DHCPv6 Server
in order to initiate an Active Leasequery exchange. If the attempt
fails, the Requestor MAY retry.
If an Active Leasequery is terminated prematurely by a LEASEQUERY-
DONE with a DHCPv6 status code (carried in an OPTION_STATUS_CODE
option) of QueryTerminated or by the failure of the connection over
which it was being submitted, the requestor MAY retry the request
after the creation of a new connection.
Messages from the DHCPv6 server come as multiple responses to a
single ACTIVELEASEQUERY message. Thus, each ACTIVELEASEQUERY request
MUST have an xid (transaction-id) unique on the connection on which
it is sent, and all of the messages which come as a response to it
contain the same xid as the request. It is the xid which allows the
data-streams of two or more different ACTIVELEASEQUERY requests to be
de-multiplexed by the requestor.
8.2. Initiating a Connection
A Requestor SHOULD be able to operate in either insecure or secure
mode. This MAY be a feature that is administratively controlled.
When operating in insecure mode, requestor should proceed with the
Active Leasequery request after the establishment of a TCP
connection.
Raghuvanshi, et al. Expires December 11, 2015 [Page 13]
Internet-Draft DHCPv6 Active Leasequery June 2015
When operating in secure mode, requestor MUST attempt to negotiate a
TLS [RFC5246] connection over the TCP connection. If this
negotiation fails, the requestor MUST drop the TCP connection.
A requestor requests the establishment of a TLS connection by sending
the STARTTLS message to the DHCPv6 server as the first message over
the TCP connection. This message indicates to the DHCPv6 server that
a TLS connection over this TCP connection is desired. There are four
possibilities after the requestor sends the STARTTLS message to the
DHCPv6 server:
1. No response from the DHCPv6 server.
2. The DHCPv6 server drops the TCP connection after it receives the
STARTTLS message.
3. DHCPv6 server responds with REPLY [RFC3315] message with DHCPv6
status code of TLSConnectionRefused.
4. DHCPv6 server responds with REPLY [RFC3315] message without
DHCPv6 status code, indicating success.
In any of the first three possibilities, the DHCPv6 server can be
assumed to not support TLS. In this case, the requestor MUST drop
the TCP connection.
In the final possibility, where the DHCPv6 server has responded with
a REPLY message without DHCPv6 status code in response to the
requestor's STARTTLS message, the requestor SHOULD initiate the
exchange of the messages involved in a TLS handshake [RFC5246].
During the TLS handshake, the requestor MUST verify DHCPv6 server's
digital certificate.
If the handshake exchange yields a functioning TLS connection, then
the requestor SHOULD transmit an Active Leasequery message over that
TLS connection and use that TLS connection for all further
interactions in which it engages with the DHCPv6 server over this TCP
connection.
If the handshake exchange does not yield a functioning TLS
connection, then the requestor MUST drop the TCP connection.
8.3. Forming an Active Leasequery
The Active Leasequery is designed to create a long lived connection
between the requestor and the DHCPv6 server processing the active
query. The DHCPv6 server SHOULD send binding information back across
this connection with minimal delay after it learns of the binding
Raghuvanshi, et al. Expires December 11, 2015 [Page 14]
Internet-Draft DHCPv6 Active Leasequery June 2015
information. It learns about bindings either because it makes the
bindings itself or because it has received information about a
binding from another server.
An important capability of the Active Leasequery is the ability of
the requestor to specify that some recent data be sent immediately to
the requestor in parallel with the transmission of the ongoing
binding information in more or less real time. This capability is
used in order to allow an Active Leasequery requestor to recover
missed information in the event that it temporarily loses
connectivity with the DHCPv6 server processing a previous Active
Leasequery.
Note that until all of the recent data (catch-up data) has been
received, the requestor MUST NOT keep track of the base-time
(OPTION_LQ_BASE_TIME) received in Leasequery reply messages to use
later in a subsequent Active Leasequery request.
This capability is enabled by the transmission of an
OPTION_LQ_BASE_TIME option with each Leasequery reply sent as the
result of a previous Active Leasequery. The requestor SHOULD keep
track of the highest base-time received from a particular DHCPv6
server over an Active Leasequery connection, and in the event that
the requestor finds it necessary (for whatever reason) to reestablish
an Active Leasequery connection to that DHCPv6 server, the requestor
SHOULD place this highest base-time value into an
OPTION_LQ_START_TIME option in the new Active Leasequery request.
If the requestor doesn't wish to request an update of information
missed when it was not connected to the DHCPv6 server, then it SHOULD
NOT include the OPTION_LQ_START_TIME option in the Active Leasequery
request.
If the TCP connection becomes blocked or stops being writable while
the requestor is sending its query, the requestor SHOULD terminate
the connection after BULK_LQ_DATA_TIMEOUT. We make this
recommendation to allow requesters to control the period of time they
are willing to wait before abandoning a connection, independent of
notifications from the TCP implementations they may be using.
8.4. Processing Active Replies
The Requestor attempts to read a DHCPv6 LEASEQUERY-REPLY message from
the TCP connection. If the stream of replies becomes blocked, the
Requestor SHOULD terminate the connection after
ACTIVE_LQ_RCV_TIMEOUT, and MAY begin retry processing if configured
to do so.
Raghuvanshi, et al. Expires December 11, 2015 [Page 15]
Internet-Draft DHCPv6 Active Leasequery June 2015
The requestor examines the LEASEQUERY-REPLY message, and determines
how to proceed. Message validation rules are specified in DHCPv6
Leasequery [RFC5007] and DHCPv6 Bulk Leasequery [RFC5460]. If the
reply contains an DHCPv6 status code (carried in an
OPTION_STATUS_CODE option), the requestor should follow the
recommendations in [RFC5007].
Note that an Active Leasequery request specifically requests the
DHCPv6 server to create a long-lived connection which may not have
data transferring continuously during its lifetime. Therefore the
DHCPv6 server SHOULD send a LEASEQUERY-DATA message without binding
data (OPTION_CLIENT_DATA) every ACTIVE_LQ_IDLE_TIMEOUT seconds
(default 60) in order for the requestor to know that the connection
remains alive. This approach is followed only when connection is
idle (i.e. server has no binding data to send). During normal
binding data exchange, receiving of LEASEQUERY-DATA message by
requestor itself signifies that connection is active. Note that the
default for ACTIVE_LQ_RCV_TIMEOUT is 120 seconds, twice the value of
the ACTIVE_LQ_IDLE_TIMEOUT's default of 60 seconds which drives the
DHCPv6 server to send messages. Thus ACTIVE_LQ_RCV_TIMEOUT controls
how sensitive the requestor is to be to delays by the DHCPv6 server
in sending updates or LEASEQUERY-DATA messages.
A single Active Leasequery can and usually will result in a large
number of replies. The Requestor MUST be prepared to receive more
than one reply with transaction-ids matching a single
ACTIVELEASEQUERY message from a single DHCPv6 server.
An Active Leasequery has two regimes -- during the catch-up phase, if
any, and after any catch-up phase. If the Active Leasequery was
requested with an OPTION_LQ_START_TIME option, the Active Leasequery
starts out in the catch-up phase. See Section 8.4.1 for information
on processing during the catch-up phase, as well as how to determine
when the catch-up phase is complete.
The updates sent by the DHCPv6 server during the catch-up phase are
not in the order that the lease state data was updated. Therefore,
the OPTION_LQ_BASE_TIME option from messages during this phase MUST
NOT be saved and used to compute the subsequent ACTIVELEASEQUERY
message's OPTION_LQ_START_TIME option.
After the catch-up phase, or during the entire series of messages
received as the response to an Active Leasequery request with no
OPTION_LQ_START_TIME (and therefore no catch-up phase), the
OPTION_LQ_BASE_TIME option of the most recent message SHOULD be saved
as a record of the most recent time that data was received. This
base-time (in the context of the DHCPv6 server) can be used in a
Raghuvanshi, et al. Expires December 11, 2015 [Page 16]
Internet-Draft DHCPv6 Active Leasequery June 2015
subsequent Active Leasequery message's OPTION_LQ_START_TIME after a
loss of the Active Leasequery connection.
The LEASEQUERY-DONE message MAY unilaterally terminate a successful
Active Leasequery request which is currently in progress in the event
that the DHCPv6 server determines that it cannot continue processing
an ACTIVELEASEQUERY request. For example, when a server is requested
to shut down it SHOULD send a LEASEQUERY-DONE message with a DHCPv6
status code of QueryTerminated and include OPTION_LQ_BASE_TIME option
in the message. This SHOULD be the last message on that connection,
and once the message has been transmitted, the server should close
the connection.
After receiving LEASEQUERY-DONE with a QueryTerminated status from a
server, the Requestor MAY close the TCP connection to that server.
8.4.1. Processing Replies from a Request Containing a
OPTION_LQ_START_TIME
If the Active Leasequery was requested with an OPTION_LQ_START_TIME
option, the DHCPv6 server will attempt to send information about all
bindings that changed since the time specified in the
OPTION_LQ_START_TIME. This is the catch-up phase of the Active
Leasequery processing. The DHCPv6 server MAY also begin immediate
updates over the same connection of real-time binding information
changes. Thus, the catch-up phase may run in parallel with the
normal updates generated by the Active Leasequery request.
A DHCPv6 server MAY keep only a limited amount of time ordered
information available to respond to an Active Leasequery request
containing an OPTION_LQ_START_TIME option. Thus, it is possible that
the time specified in the OPTION_LQ_START_TIME option represents a
time not covered by the time ordered information kept by the DHCPv6
server. If this should occur, and there is not enough data saved in
the DHCPv6 server to satisfy the request specified by the
OPTION_LQ_START_TIME option, the DHCPv6 server will reply immediately
with a LEASEQUERY-REPLY message with a DHCPv6 status code of
DataMissing with a base-time option equal to the server's current
time. This will signal the end of the catch-up phase, and the only
updates that will subsequently be received on this connection are the
real-time updates from the Active Leasequery request.
If there is enough data saved to satisfy the request, then
LEASEQUERY-REPLY (with OPTION_STATUS_CODE of Success or reply without
OPTION_STATUS_CODE option) and LEASEQUERY-DATA messages will begin
arrive from the DHCPv6 server. Some of these messages will be
related to the OPTION_LQ_START_TIME request and be part of the catch-
up phase. Some of these messages will be real-time updates of
Raghuvanshi, et al. Expires December 11, 2015 [Page 17]
Internet-Draft DHCPv6 Active Leasequery June 2015
binding changes taking place in the DHCPv6 server. In general, there
is no way to determine the source of each message.
The updates sent by the DHCPv6 server during the catch-up phase are
not in the order that the binding data was updated. Therefore, until
the catch-up phase is complete, the latest base-time value received
from a DHCPv6 server processing an Active Leasequery request cannot
be reset from the incoming messages (and used in a subsequent Active
Leasequery's query-start-time option), because to do so would
compromise the ability to recover lost information if the Active
Leasequery were to terminate prior to the completion of the catch-up
phase.
The requestor will know that the catch-up phase is complete when the
DHCPv6 server will transmit a LEASEQUERY-DATA message with the DHCPv6
status code of CatchUpComplete (or LEASEQUERY-REPLY message with a
DHCPv6 status code of DataMissing, as discussed above). Once this
message is transmitted, all additional LEASEQUERY-DATA messages will
relate to real-time ("new") binding changes in the DHCPv6 server.
As discussed in Section 8.4, the requestor SHOULD keep track of the
latest base-time option value received over a particular connection,
to be used in a subsequent Active Leasequery request -- but only if
the catch-up phase is complete. Prior to the completion of the
catch-up phase, if the connection should go away or if the requestor
receives a LEASEQUERY-DONE message, then when it reconnects it MUST
use the base-time value from the previous connection and not any
base-time value received from the recently closed connection.
In the event that there was enough data available to the DHCPv6
server to begin to satisfy the request implied by the
OPTION_LQ_START_TIME option, but during the processing of that data
the server found that it was unable to continue (perhaps there was
barely enough, the connection is very slow, and the aging algorithm
causes the saved data to become unavailable) the DHCPv6 server will
terminate the catch-up phase of processing immediately by sending a
LEASEQUERY-DATA message with a DHCPv6 status code of DataMissing and
with a base-time option of the current time.
The requestor MUST NOT assume that every individual state change of
every binding during the period from the time specified in the
OPTION_LQ_START_TIME and the present is replicated in an Active
Leasequery reply message. The requestor MAY assume that at least one
Active Leasequery reply message will exist for every binding which
had one or more changes of state during the period specified by the
OPTION_LQ_START_TIME and the current time. The last message for each
binding will contain the state at the current time, and there may be
Raghuvanshi, et al. Expires December 11, 2015 [Page 18]
Internet-Draft DHCPv6 Active Leasequery June 2015
one or more messages concerning a single binding during the catch-up
phase of processing.
Bindings can change multiple times while the requester was not
connected (that is, during the time from the OPTION_LQ_START_TIME and
the present). The requestor will only receive information about the
current state of the binding, not information about each state change
that occurred during the period from the OPTION_LQ_START_TIME to the
present.
If the LEASEQUERY-REPLY or LEASEQUERY-DATA message containing a
DHCPv6 status code of DataMissing is received and the requestor is
interested in keeping its database up to date with respect to the
current state of bindings in the DHCPv6 server, then the requestor
SHOULD issue a Bulk Leasequery request to recover the information
missing from its database. This Bulk Leasequery request should
include a OPTION_LQ_START_TIME option with the same value as the
OPTION_LQ_START_TIME option previously included in the
ACTIVELEASEQUERY responses from the DHCPv6 server, and an
OPTION_LQ_END_TIME option equal to the OPTION_LQ_BASE_TIME option
returned by the DHCPv6 server in the LEASEQUERY-REPLY or LEASEQUERY-
DATA message with the DHCPv6 status code of DataMissing.
Typically, the requestor would have one connection open to a DHCPv6
server for an Active Leasequery request and possibly one additional
connection open for a Bulk Leasequery request to the same DHCPv6
server to fill in the data that might have been missed prior to the
initiation of the Active Leasequery. The Bulk Leasequery connection
would typically run to completion and be closed, leaving one Active
Leasequery connection open to a single DHCPv6 server. Alternatively,
both requests could be issued over a single connection.
8.5. Processing Time Values in Leasequery messages
Active or Bulk Leasequery requests may be made to a DHCPv6 server
whose absolute time may not be synchronized with the local time of
the requestor. Thus, there are at least two time contexts in even
the simplest Active or Bulk Leasequery response.
If the requestor of an Active or Bulk Leasequery is saving the data
returned in some form, it has a requirement to store a variety of
time values, and some of these will be time in the context of the
requestor and some will be time in the context of the DHCPv6 server.
When receiving an Active or Bulk Leasequery reply message from the
DHCPv6 server, the message will contain an OPTION_LQ_BASE_TIME
option. The time contained in this OPTION_LQ_BASE_TIME option is in
the context of the DHCPv6 server. As such, it is an ideal time to
Raghuvanshi, et al. Expires December 11, 2015 [Page 19]
Internet-Draft DHCPv6 Active Leasequery June 2015
save and use as input to an Active or Bulk Leasequery message in the
OPTION_LQ_START_TIME or OPTION_LQ_END_TIME option, should the
requestor need to ever issue an Active or Bulk Leasequery message
using these option as part of a later query, since these option
requires a time in the context of the DHCPv6 server.
In addition to saving the OPTION_LQ_BASE_TIME for possible future use
in OPTION_LQ_START_TIME or OPTION_LQ_END_TIME option, the
OPTION_LQ_BASE_TIME is used as part of the conversion of the other
times in the Leasequery message to values which are meaningful in the
context of the requestor.
In systems whose clocks are synchronized, perhaps using NTP, the
clock skew will usually be zero, which is not only acceptable, but
desired.
8.6. Examples
These examples illustrate what a series of queries and responses
might look like. These are only examples -- there are no requirement
that these sequence must be followed.
8.6.1. Query Failure
This example illustrates the message flows in case DHCPv6 server
identifies that it cannot accept and/or process Active Leasequery
request from the requestor. This could be because of various reasons
(i.e. UnknownQueryType, MalformedQuery, NotConfigured, NotAllowed,
NotSupported).
Client Server
------ ------
ACTIVELEASEQUERY xid 1 ----->
<----- LEASEQUERY-REPLY xid 1 (w/error)
8.6.2. Data Missing on Server
This example illustrates the message flows in case DHCPv6 server
identifies that it does not have enough data saved to satisfy the
request specified by the OPTION_LQ_START_TIME option.
In this case the DHCPv6 server will reply immediately with a
LEASEQUERY-REPLY message with a DHCPv6 status code of DataMissing
with a base-time option equal to the server's current time. This
will signal the end of the catch-up phase, and the only updates that
Raghuvanshi, et al. Expires December 11, 2015 [Page 20]
Internet-Draft DHCPv6 Active Leasequery June 2015
will subsequently be received on this connection are the real-time
updates from the Active Leasequery request.
Client Server
------ ------
ACTIVELEASEQUERY xid 2 ----->
<----- LEASEQUERY-REPLY xid 2 (w/error)
<----- LEASEQUERY-DATA xid 2
<----- LEASEQUERY-DATA xid 2
<----- LEASEQUERY-DATA xid 2
8.6.3. Successful Query
This example illustrates the message flows in case of successful
query processing by DHCPv6 server.
In this case the DHCPv6 server will reply immediately with a
LEASEQUERY-REPLY message (with OPTION_STATUS_CODE of Success or reply
without OPTION_STATUS_CODE option), followed by binding data in
LEASEQUERY-DATA messages. In case, DHCPv6 server wants to abort in-
process request and terminate the connection due to some reason, it
sends LEASEQUERY-DONE with error code present in OPTION_STATUS_CODE
option.
Client Server
------ ------
ACTIVELEASEQUERY xid 3 ----->
<----- LEASEQUERY-REPLY xid 3
<----- LEASEQUERY-DATA xid 3
<----- LEASEQUERY-DATA xid 3
<----- LEASEQUERY-DATA xid 3
<----- LEASEQUERY-DATA xid 3
<----- LEASEQUERY-DONE xid 3 (w/error)
8.7. Closing Connections
The Requestor or DHCPv6 Leasequery server MAY close its end of the
TCP connection at any time. The Requestor MAY choose to retain the
connection if it intends to issue additional queries. Note that this
requestor behavior does not guarantee that the connection will be
available for additional queries: the server might decide to close
the connection based on its own configuration.
Raghuvanshi, et al. Expires December 11, 2015 [Page 21]
Internet-Draft DHCPv6 Active Leasequery June 2015
9. Server Behavior
A DHCPv6 server which supports Active Leasequery MUST support DHCPv6
Bulk Leasequery [RFC5460] and as extended herein.
9.1. Accepting Connections
DHCPv6 servers that implement DHCPv6 Active Leasequery listen for
incoming TCP connections. Approach used in accepting the requestor
connection is same as specified in DHCPv6 Bulk Leasequery [RFC5460].
DHCPv6 servers SHOULD be able to operate in either insecure or secure
mode. This MAY be a mode that is administratively controlled, where
the server will require a TLS connection to operate or will only
operate without a TLS connection.
When operating in insecure mode, DHCPv6 server simply waits for the
requestor to send the Active Leasequery request after the
establishment of TCP connection. If it receives a STARTTLS message,
it MUST respond with REPLY [RFC3315] message with DHCPv6 status code
of TLSConnectionRefused.
When operating in secure mode, DHCPv6 servers MUST support TLS
[RFC5246] to protect the integrity and privacy of the data
transmitted over the TCP connection. DHCPv6 servers SHOULD negotiate
a TLS connection with the requestor who asks for one, and MUST drop
the TCP connections which are not secured with TLS.
A requestor will request a TLS connection by sending a STARTTLS as
the first message over a newly created TCP connection. If the DHCPv6
server supports TLS connections and has not been configured to not
allow them on this link, the DHCPv6 server SHOULD respond to this
STARTTLS message by sending a REPLY [RFC3315] message without DHCPv6
status code back to the requestor. This indicates to the requestor
that the DHCPv6 server will support the negotiation of a TLS
connection over this existing TCP connection.
If for some reason the DHCPv6 server cannot or has been configured to
not support a TLS connection, then it SHOULD send a REPLY message
with DHCPv6 status code of TLSConnectionRefused back to the
requestor.
In the event that the DHCPv6 server sends a REPLY message without
DHCPv6 status code option included (which indicates success), the
requestor is supposed to initiate a TLS handshake [RFC5246] (see
Section 8.2). During the TLS handshake, the DHCPv6 server MUST
verify the requestor's digital certificate.
Raghuvanshi, et al. Expires December 11, 2015 [Page 22]
Internet-Draft DHCPv6 Active Leasequery June 2015
If the TLS handshake is not successful in creating a TLS connection,
the server MUST drop the TCP connection.
9.2. Rejecting Connections
Servers that do not implement DHCPv6 Active and Bulk Leasequery
SHOULD NOT listen for incoming TCP connections for these requests.
If the DHCPv6 server supporting Bulk Leasequery and not Active
Leasequery receives an Active Leasequery request, it SHOULD send a
LEASEQUERY-REPLY with DHCPv6 status code as NotSupported. It SHOULD
close the TCP connection after this error is signaled.
9.3. Replying to an Active Leasequery
The DHCPv6 Leasequery [RFC5007] specification describes the initial
construction of LEASEQUERY-REPLY messages. Use of the LEASEQUERY-
REPLY and LEASEQUERY-DATA messages to carry multiple bindings is
described in DHCPv6 Bulk Leasequery [RFC5460]. Message transmission
and framing for TCP is described in Section 6.1.
If the connection becomes blocked while the server is attempting to
send reply messages, the server SHOULD terminate the TCP connection
after ACTIVE_LQ_SEND_TIMEOUT. This timeout governs for how long the
DHCPv6 server is prepared to wait for the requestor to read and
process enough information to unblock the TCP connection. The
default is two minutes, which means that if more than two minutes
goes by without the requestor reading enough information to unblock
the TCP connection, the DHCPv6 server SHOULD drop the TCP connection.
If the DHCPv6 server encounters an error during initial processing of
the ACTIVELEASEQUERY message, it SHOULD send a LEASEQUERY-REPLY
message containing an error code of some kind in a DHCPv6 status code
option. It SHOULD close the connection after this error is signaled.
If the DHCPv6 server encounters an error during later processing of
the ACTIVELEASEQUERY message, it SHOULD send a LEASEQUERY-DONE
containing an error code of some kind in a DHCPv6 status code option.
It SHOULD close the connection after this error is signaled.
If the server finds any bindings satisfying a query, it SHOULD send
each binding's data in a reply message. The first reply message is a
LEASEQUERY-REPLY. The binding data is carried in an
OPTION_CLIENT_DATA option, as specified in [RFC5007]. The server
SHOULD send subsequent bindings in LEASEQUERY-DATA messages, which
can avoid redundant data (such as the requestor's Client-ID).
Raghuvanshi, et al. Expires December 11, 2015 [Page 23]
Internet-Draft DHCPv6 Active Leasequery June 2015
Every reply to an Active Leasequery request MUST contain the
information specified in replies to a DHCPv6 Bulk Leasequery request
[RFC5460].
Some servers can be configured to respond to a DHCPv6 Leasequery
[RFC5007] and DHCPv6 Bulk Leasequery [RFC5460] for an IPv6 binding
which is reserved in such a way that it appears that the IPv6 binding
is leased to the DHCP client for which it is reserved. These servers
SHOULD also respond to an Active Leasequery request with the same
information as they would to a Bulk Leasequery request when they
first determine that the IPv6 binding is reserved to a DHCP client.
If an Active Leasequery or Bulk Leasequery request contains
OPTION_LQ_BASE_TIME option code present in OPTION_ORO, the DHCPv6
server MUST include OPTION_LQ_BASE_TIME option in every reply for
this request. The value for base-time option is current absolute
time in the DHCPv6 server's context.
If an Active Leasequery request contains an OPTION_LQ_START_TIME
option, it indicates that the requestor would like the DHCPv6 server
to send it not only messages that correspond to DHCPv6 binding
activity that occurs subsequent to the receipt of the Active
Leasequery request, but also messages that correspond to DHCPv6
binding activity that occurred prior to the Active Leasequery
request.
If OPTION_LQ_END_TIME option appears in an Active Leasequery request,
the DHCPv6 server SHOULD send a LEASEQUERY-REPLY message with a
DHCPv6 status code of MalformedQuery and terminate the connection.
In order to implement a meaningful response to this query, the DHCPv6
server MAY keep track of the binding activity and associate changes
with particular base-time values from the messages. Then, when
requested to do so by an Active Leasequery request containing a
OPTION_LQ_START_TIME option, the DHCPv6 server can respond with
replies for all binding activity occurring on that
OPTION_LQ_START_TIME or later times.
These replies based on the OPTION_LQ_START_TIME MAY be interleaved
with the messages generated due to current binding activity.
Once the transmission of the DHCPv6 Leasequery messages associated
with the OPTION_LQ_START_TIME option are complete, a LEASEQUERY-DATA
message MUST be sent with a DHCPv6 status code value of
CatchUpComplete.
The DHCPv6 server SHOULD, but is not required to, keep track of a
limited amount of previous binding activity. The DHCPv6 server MAY
Raghuvanshi, et al. Expires December 11, 2015 [Page 24]
Internet-Draft DHCPv6 Active Leasequery June 2015
choose to only do this in the event that it has received at least one
Active Leasequery request in the past, as to do so will almost
certainly entail some utilization of resources which would be wasted
if there are no Active Leasequery requestors for this DHCPv6 server.
The DHCPv6 server SHOULD make the amount of previous binding activity
it retains configurable. There is no requirement on the DHCPv6
server to retain this information over a server restart (or even to
retain such information at all).
Unless there is an error or some requirement to cease processing a
Active Leasequery request yielding a LEASEQUERY-DONE message, such as
a server shutdown, there will be no LEASEQUERY-DONE message at the
conclusion of the Active Leasequery processing because that
processing will not conclude but will continue until either the
requestor or the server drops the connection.
9.4. Multiple or Parallel Queries
Every Active Leasequery request MUST be made on a single TCP
connection where there is no other request active at the time the
request is made.
Typically, a requestor of an Active Leasequery would not need to send
a second Active Leasequery while the first is still active. However,
sending an Active Leasequery and a Bulk Leasequery in parallel would
be possible and reasonable. In case of parallel Active and Bulk
Leasequeries, requestor MUST use different TCP connections.
This MAY be a feature that is administratively controlled. Servers
that are able to process queries in parallel SHOULD offer
configuration that limits the number of simultaneous queries
permitted from any one requestor, in order to control resource use if
there are multiple requesters seeking service.
9.5. Closing Connections
The server MUST close its end of the TCP connection if it encounters
an error sending data on the connection. The server MUST close its
end of the TCP connection if it finds that it has to abort an in-
process request. A server aborting an in-process request SHOULD
attempt to signal that to its requestors by using the QueryTerminated
status code in the DHCPv6 status code option in a LEASEQUERY-DONE
message. If the server detects that the requestor end has been
closed, the server MUST close its end of the connection.
The server SHOULD limit the number of connections it maintains, and
SHOULD close idle connections to enforce the limit.
Raghuvanshi, et al. Expires December 11, 2015 [Page 25]
Internet-Draft DHCPv6 Active Leasequery June 2015
10. Security Considerations
The "Security Considerations" section of [RFC3315] details the
general threats to DHCPv6. The DHCPv6 Leasequery specification
[RFC5007] describes recommendations for the Leasequery protocol,
especially with regard to relayed Leasequery messages, mitigation of
packet-flooding denial-of-service (DoS) attacks, restriction to
trusted requestors, and use of IPsec [RFC4301].
The use of TCP introduces some additional concerns. Attacks that
attempt to exhaust the DHCPv6 server's available TCP connection
resources can compromise the ability of legitimate requestors to
receive service. Malicious requestors who succeed in establishing
connections, but who then send invalid queries, partial queries, or
no queries at all also can exhaust a server's pool of available
connections. We recommend that servers offer configuration to limit
the sources of incoming connections, that they limit the number of
accepted connections, and that they limit the period of time during
which an idle connection will be left open.
Authentication for DHCP Messages [RFC3315] MUST NOT be used to
attempt to secure transmission of the messages described in this
document.
11. IANA Considerations
IANA is requested to assign new DHCPv6 Option Codes in the registry
maintained in http://www.iana.org/assignments/dhcpv6-parameters:
OPTION_LQ_BASE_TIME
OPTION_LQ_START_TIME
OPTION_LQ_END_TIME
IANA is requested to assign new values in the registry of DHCPv6
Status Codes maintained in http://www.iana.org/assignments/
dhcpv6-parameters:
DataMissing
CatchUpComplete
NotSupported
TLSConnectionRefused
Raghuvanshi, et al. Expires December 11, 2015 [Page 26]
Internet-Draft DHCPv6 Active Leasequery June 2015
IANA is requested to assign values for the following new DHCPv6
Message types in the registry maintained in
http://www.iana.org/assignments/dhcpv6-parameters:
ACTIVELEASEQUERY
STARTTLS
12. Acknowledgements
Some of the concept and content, present in this document, are based
on DHCPv4 Active Leasequery which was originally proposed by Kim
Kinnear, Bernie Volz, Mark Stapp and Neil Russell.
13. Modification History
14. References
14.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3315] Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C.,
and M. Carney, "Dynamic Host Configuration Protocol for
IPv6 (DHCPv6)", RFC 3315, July 2003.
[RFC3633] Troan, O. and R. Droms, "IPv6 Prefix Options for Dynamic
Host Configuration Protocol (DHCP) version 6", RFC 3633,
December 2003.
[RFC5007] Brzozowski, J., Kinnear, K., Volz, B., and S. Zeng,
"DHCPv6 Leasequery", RFC 5007, September 2007.
[RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security
(TLS) Protocol Version 1.2", RFC 5246, August 2008.
[RFC5460] Stapp, M., "DHCPv6 Bulk Leasequery", RFC 5460, February
2009.
14.2. Informative References
[RFC4301] Kent, S. and K. Seo, "Security Architecture for the
Internet Protocol", RFC 4301, December 2005.
Raghuvanshi, et al. Expires December 11, 2015 [Page 27]
Internet-Draft DHCPv6 Active Leasequery June 2015
[RFC7414] Duke, M., Braden, R., Eddy, W., Blanton, E., and A.
Zimmermann, "A Roadmap for Transmission Control Protocol
(TCP) Specification Documents", RFC 7414, February 2015.
Authors' Addresses
Dushyant Raghuvanshi
Cisco Systems, Inc.
Cessna Business Park,
Varthur Hobli, Outer Ring Road,
Bangalore, Karnataka 560037
India
Phone: +91 (080) 4365-7476
Email: draghuva@cisco.com
Kim Kinnear
Cisco Systems, Inc.
1414 Massachusetts Ave.
Boxborough, Massachusetts 01719
USA
Phone: +1 (978) 936-0000
Email: kkinnear@cisco.com
Deepak Kukrety
Cisco Systems, Inc.
Cessna Business Park,
Varthur Hobli, Outer Ring Road,
Bangalore, Karnataka 560037
India
Phone: +91 (080) 4365-7474
Email: dkukrety@cisco.com
Raghuvanshi, et al. Expires December 11, 2015 [Page 28]
Html markup produced by rfcmarkup 1.129b, available from
https://tools.ietf.org/tools/rfcmarkup/