[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]
Versions: 00 01 02 03 04 05 06 07 08 RFC 4384
GROW WG D. Meyer
Internet-Draft August 22, 2005
Expires: February 23, 2006
BGP Communities for Data Collection
draft-ietf-grow-collection-communities-08
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on February 23, 2006.
Copyright Notice
Copyright (C) The Internet Society (2005).
Abstract
BGP communities (RFC 1997) are used by service providers for many
purposes, including tagging of customer, peer, and geographically
originated routes. Such tagging is typically used to control the
scope of redistribution of routes within a provider's network, and to
its peers and customers. With the advent of large scale BGP data
collection (and associated research), it has become clear that the
information carried in such communities is essential for a deeper
understanding of the global routing system. This memo defines
standard (outbound) communities and their encodings for export to BGP
Meyer Expires February 23, 2006 [Page 1]
Internet-Draft BGP Communities for Data Collection August 2005
route collectors.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1. Peers and Peering . . . . . . . . . . . . . . . . . . . . 3
2.2. Customer Routes . . . . . . . . . . . . . . . . . . . . . 4
2.3. Peer Routes . . . . . . . . . . . . . . . . . . . . . . . 4
2.4. Internal Routes . . . . . . . . . . . . . . . . . . . . . 4
2.5. Internal More Specific Routes . . . . . . . . . . . . . . 4
2.6. Special Purpose Routes . . . . . . . . . . . . . . . . . . 4
2.7. Upstream Routes . . . . . . . . . . . . . . . . . . . . . 4
2.8. National Routes . . . . . . . . . . . . . . . . . . . . . 5
2.9. Regional Routes . . . . . . . . . . . . . . . . . . . . . 5
3. RFC 1997 Community Encoding and Values . . . . . . . . . . . . 5
4. Community Values for BGP Data Collection . . . . . . . . . . . 5
4.1. Extended Communities . . . . . . . . . . . . . . . . . . . 7
4.2. Four-octet AS specific extended communities . . . . . . . 8
5. Note on BGP UPDATE Packing . . . . . . . . . . . . . . . . . . 9
6. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 9
7. Security Considerations . . . . . . . . . . . . . . . . . . . 9
7.1. Total Path Attribute Length . . . . . . . . . . . . . . . 9
8. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 10
9. References . . . . . . . . . . . . . . . . . . . . . . . . . . 10
9.1. Normative References . . . . . . . . . . . . . . . . . . . 10
9.2. Informative References . . . . . . . . . . . . . . . . . . 11
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 12
Intellectual Property and Copyright Statements . . . . . . . . . . 13
Meyer Expires February 23, 2006 [Page 2]
Internet-Draft BGP Communities for Data Collection August 2005
1. Introduction
BGP communities [RFC1997] are used by service providers for many
purposes, including tagging of customer, peer, and geographically
originated routes. Such tagging is typically used to control the
scope of redistribution of routes within a providers network, and to
its customers and peers. Communities are also used for a wide
variety of other applications, such as allowing customers to set
attributes such as LOCAL_PREF [RFC1771] by sending appropriate
communities to their service provider. Other applications include
signaling various types of VPNs (e.g., VPLS [I-D.ietf-ppvpn-vpls-
requirements]), and carrying link bandwidth for traffic engineering
applications [I-D.ietf-idr-bgp-ext-communities].
With the advent of large scale BGP data collection [RV][RIS] (and
associated research), it has become clear that the geographical and
topological information, as well as the relationship the provider has
to the source of a route (e.g., transit, peer, or customer), carried
in such communities is essential for a deeper understanding of the
global routing system. This memo defines standard communities for
export to BGP route collectors. These communities represent a
significant part of information carried by service providers as of
this writing, and as such could be useful for internal use by service
providers. However, such use is beyond the scope of this memo.
Finally, those involved in BGP data analysis are encouraged to verify
with their data sources as to which peers implement this scheme (as
there is a large amount of existing data as well as many legacy
peerings).
The remainder of this memo is organized as follows. Section 2
provides both the definition of terms used as well as the semantics
of the communities used for BGP data collection, and section 3
defines the corresponding encodings for RFC 1997 [RFC1997]
communities. Finally, section 4 defines the encodings for use with
extended communities [I-D.ietf-idr-bgp-ext-communities].
2. Definitions
In this section, we define the terms used and the categories of
routes that may be tagged with communities. This tagging is often
refered to as coloring, and we refer to a route's "color" as its
community value. The categories defined here are loosely modeled on
those described in [WANG] and [HUSTON].
2.1. Peers and Peering
Consider two network service providers, A and B. Service providers A
Meyer Expires February 23, 2006 [Page 3]
Internet-Draft BGP Communities for Data Collection August 2005
and B are defined to be peers when (i). A and B exchange routes via
BGP, and (ii). traffic exchange between A and B is settlement-free.
This arrangement is also typically known as "peering". Peers
typically exchange only their respective customer routes (see
"Customer Routes" below), and hence exchange only their respective
customer traffic. See [HUSTON] for a more in-depth discussion of the
business models surrounding peers and peering.
2.2. Customer Routes
Customer routes are those routes which are heard from a customer via
BGP and are propagated to peers and other customers. Note that a
customer can be an enterprise or another network service provider.
These routes are sometimes called client routes [HUSTON].
2.3. Peer Routes
Peer routes are those routes heard from peers via BGP, and not
propagated to other peers. In particular, these routes are only
propagated to the service provider's customers.
2.4. Internal Routes
Internal routes are those routes that a service provider originates
and passes to its peers and customers. These routes are frequently
taken out of the address space allocated to a provider.
2.5. Internal More Specific Routes
Internal more-specific routes are those routes which are frequently
used for circuit load balancing purposes, IGP route reduction, and
also may correspond to customer services which are not visible
outside the service provider's network. Internal more specific
routes are not exported to any external peer.
2.6. Special Purpose Routes
Special purpose routes are those routes which do not fall into any of
the other classes described here. In those cases in which such
routes need to be distinguished, a service provider may color such
routes with a unique value. Examples of special purpose routes
include anycast routes, and routes for overlay networks.
2.7. Upstream Routes
Upstream routes are typically learned from upstream service provider
as part of a transit service contract executed with the upstream
provider.
Meyer Expires February 23, 2006 [Page 4]
Internet-Draft BGP Communities for Data Collection August 2005
2.8. National Routes
These are route sets that are sourced from and/or received within a
particular country.
2.9. Regional Routes
Several global backbones implement regional policy based on their
deployed footprint, and on strategic and business imperatives.
Service providers often have settlement-free interconnections with an
AS in one region, and that same AS is a customer in another region.
This mandates use of regional routing, including community attributes
set by the network in question to allow easy discrimination among
regional routes. For example, service providers may treat a route
set received from another service provider in Europe differently than
the same route set received in North America, as it is common
practice to sell transit in one region while peering in the other.
3. RFC 1997 Community Encoding and Values
In this section we provide RFC 1997 [RFC1997] community values for
the categories described above. RFC 1997 communities are encoded as
BGP Type Code 8, and are treated as 32 bit values ranging from
0x0000000 through 0xFFFFFFF. The values 0x0000000 through 0x0000FFFF
and 0xFFFF0000 through 0xFFFFFFFF are reserved.
The best current practice among service providers is to use the high
order two octets to represent the provider's AS number, and the low
order two octets to represent the classification of the route, as
depicted below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| <AS> | <Value> |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
where <AS> is the 16 bit AS number. For example, the encoding
0x2A7C029A would represent the AS 10876 with value 666.
4. Community Values for BGP Data Collection
In this section we define the RFC 1997 community encoding for the
route types described above for use in BGP data collection. It is
anticipated that a service provider's internal community values will
be converted to these standard values for output to a route
Meyer Expires February 23, 2006 [Page 5]
Internet-Draft BGP Communities for Data Collection August 2005
collector.
This memo follows the best current practice of using the basic format
<AS>:<Value>. The values for the route categories are described in
the following table:
Category Value
===============================================================
Reserved <AS>:0000000000000000
Customer Routes <AS>:0000000000000001
Peer Routes <AS>:0000000000000010
Internal Routes <AS>:0000000000000011
Internal More Specific Routes <AS>:0000000000000100
Special Purpose Routes <AS>:0000000000000101
Upstream Routes <AS>:0000000000000110
Reserved <AS>:0000000000000111-
<AS>:0000011111111111
National and Regional Routes <AS>:0000100000000000-
<AS>:1111111111111111
Encoded as <AS>:<R><X><CC>
Reserved National and Regional values <AS>:0100000000000000-
<AS>:1111111111111111
Where
<AS> is the 16-bit AS
<R> is the 5-bit Region Identifier
<X> is the 1-bit satellite link indication
X = 1 for satellite links, 0 otherwise
<CC> is the 10-bit ISO-3166-2 country code [ISO3166]
and <R> takes the values:
Africa (AF) 00001
Oceania (OC) 00010
Asia (AS) 00011
Antarctica (AQ) 00100
Europe (EU) 00101
Latin America/Caribbean Islands (LAC) 00110
North America (NA) 00111
Reserved 01000-11111
Figure 2: Initially Assigned Community Values
That is:
Meyer Expires February 23, 2006 [Page 6]
Internet-Draft BGP Communities for Data Collection August 2005
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| <AS> | <R> |X| <CC> |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
For example, the encoding for a national route over a terrestrial
link in AS 10876 from the Fiji Islands would be:
<AS> = 10876 = 0x2A7C
<R> = 00010
<X> = 0
<CC> = Fiji Islands Country Code = 242 = 0011110010
In this case, the low order 16 bits are 0001000011110010 = 0x10F2
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x2A7C | 0x10F2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Note that a configuration language might allow the specification of
this community as 10876:4338 (0x10F2 == 4338 decimal).
Finally, note that these categories are not intended to be mutually
exclusive, and multiple communities can be attached where
appropriate.
4.1. Extended Communities
In some cases, the values and their encodings described in Section 4
may clash with a service provider's existing community assignments.
Extended communities [I-D.ietf-idr-bgp-ext-communities] provide a
convenient mechanism that can be used to avoid such clashes.
The Extended Communities Attribute is a transitive optional BGP
attribute with the Type Code 16, and consists of a set of extended
communities of the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type high | Type low(*) | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Value |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Meyer Expires February 23, 2006 [Page 7]
Internet-Draft BGP Communities for Data Collection August 2005
For purposes of BGP data collection, we encode the communities
described in Section 4 using the two-octet AS specific extended
community type, which has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x00 | Sub-Type | Global Administrator |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Local Administrator |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The two-octet AS specific extended community attribute encodes the
service provider's two octet Autonomous System number (as assigned by
a Regional Internet Registry, or RIR) in the Global Administrator
field, and the Local Administrator field may encode any information.
This memo assigns Sub-Type 0x0008 for BGP data collection, and
specifies that the <Value> field, as defined in section 3.1, is
carried in the low order octets of the Local Administrator field.
The two high order octets of the Local Administrator field are
reserved, and are set to 0x00 when sending and ignored upon receipt.
For example, the extended community encoding for 10876:4338
(representing a terrestrial national route in AS 10876 from the Fiji
Islands) would be:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x00 | 0x0008 | 0x2A7C |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x00 | 0x00 | 0x10F2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
4.2. Four-octet AS specific extended communities
The four-octet AS specific extended community is encoded as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x02 | 0x0008 | Global Administrator |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Global Administrator (cont.) | 0x10F2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
In this case, the 4 octet Global Administrator sub-field contains a
Meyer Expires February 23, 2006 [Page 8]
Internet-Draft BGP Communities for Data Collection August 2005
4-octets Autonomous System number assigned by the IANA.
5. Note on BGP UPDATE Packing
Note that data collection communities have the potential of making
the attribute set of a specific route more unique than it would be
otherwise (since each route collects data that is specific to it's
path inside one or more ASes). This, in turn, can affect whether
multiple routes can be grouped in the same BGP update message, and
may lead to increased use of bandwidth, router CPU cycles, and
memory.
6. Acknowledgments
The community encoding described in this memo germinated from an
interesting suggestion from Akira Kato at WIDE. In particular, the
idea would be to use the collection community values to select paths
that would result in (hopefully) more efficient access to various
services. For example, in the case of RFC 3258 [RFC3258] based DNS
anycast service, BGP routers may see multiple paths to the same
prefix, and others might be coming from the same origin with
different paths, but others might be from different region/country
(with the same origin AS).
Joe Abley, Randy Bush, Sean Donelan, Xenofontas Dimitropoulos, Vijay
Gill, John Heasley, Geoff Huston, Steve Huter, Michael Patton,
Olivier Marce, Ryan McDowell, Rob Rockell, Rob Thomas, Pekka Savola,
Patrick Verkaik and Alex Zinin all made many insightful comments on
early versions of this draft. Henk Uijterwaal suggested the use of
the ISO-3166-2 country codes.
7. Security Considerations
While this memo introduces no additional security considerations into
the BGP protocol, the information contained in the communities
defined in this memo may in some cases reveal network structure that
was not previously visible outside the provider's network. As a
result, care should be taken when exporting such communities to route
collectors. Finally, routes exported to a route collector should
also be tagged with the NO_EXPORT community (0xFFFFFF01).
7.1. Total Path Attribute Length
The communities described in this memo are intended for use on egress
to a route collector. Hence an operator may choose to overwrite its
Meyer Expires February 23, 2006 [Page 9]
Internet-Draft BGP Communities for Data Collection August 2005
internal communities with the values specified in this memo when
exporting routes to a route collector. However, operators should in
general ensure that the behavior of their BGP implementation is well-
defined when the addition of an attribute causes a PDU to exceed 4096
octets. For example, since it is common practice to use community
attributes to implement policy (among other functionality such as
allowing customers to set attributes such as LOCAL_PREF), the
behavior of an implementation when the attribute space overflows is
crucial. Among other behaviors, an implementation might usurp the
intended attribute data or otherwise cause indeterminate failures.
These behaviors can result in unanticipated community attribute sets,
and hence result in unintended policy implications.
8. IANA Considerations
This memo assigns a new Sub-Type for the AS specific extended
community type in the First Come First Served extended transitive
category. In particular, the IANA should assign Sub-type 0x0008 as
defined in Section 4.1.
In addition, this memo instructs the IANA to create two registries
for BGP Data Collection Communities, one for standard communities and
one for extended communities. Both of these registries should
initially be populated by the values described in Section 4. IETF
Consensus, usually through the Global Routing Operations Working
Group (grow) is required for the assignment of new values in these
registries (in particular, for <Value> or <R>), as described in
Figure 2 [RFC2434].
9. References
9.1. Normative References
[RFC1771] Rekhter, Y. and T. Li, "A Border Gateway Protocol 4
(BGP-4)", RFC 1771, March 1995.
[RFC1997] Chandrasekeran, R., Traina, P., and T. Li, "BGP
Communities Attribute", RFC 1997, August 1996.
[RFC2434] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs", BCP 26, RFC 2434,
October 1998.
[I-D.ietf-idr-bgp-ext-communities]
Sangli, S., Tappan, D., and Y. Rekhter, "BGP Extended
Communities Attribute",
Meyer Expires February 23, 2006 [Page 10]
Internet-Draft BGP Communities for Data Collection August 2005
draft-ietf-idr-bgp-ext-communities-07 (work in progress),
March 2004.
[ISO3166] "ISO 3166 Maintenance agency (ISO 3166/MA)", Web Page:
http://www.iso.org/iso/en/prods-services/iso3166ma/
index.html, 2004.
9.2. Informative References
[I-D.ietf-ppvpn-vpls-requirements]
Augustyn, W., "Requirements for Virtual Private LAN
Services (VPLS)", draft-ietf-ppvpn-vpls-requirements-00
(work in progress), March 2002.
[RIS] "The RIPE Routing Information Service", Web
Page: http://www.ripe.net/ris, 2004.
[RV] Meyer, D., "The Routeviews Project", Web
Page: http://www.routeviews.org, 2002.
[WANG] Wang, F. and L. Gao, "Inferring and Characterizing
Internet Routing Policies", ACM SIGCOMM Internet
Measurement Conference, 2003.
[HUSTON] Huston, G., "Interconnection, Peering, and Settlements",
Web
Page: http://www.isoc.org/inet99/proceedings/1e/1e_1.htm,
2003.
Meyer Expires February 23, 2006 [Page 11]
Internet-Draft BGP Communities for Data Collection August 2005
Author's Address
David Meyer
Email: dmm@1-4-5.net
Meyer Expires February 23, 2006 [Page 12]
Internet-Draft BGP Communities for Data Collection August 2005
Intellectual Property Statement
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Disclaimer of Validity
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Copyright Statement
Copyright (C) The Internet Society (2005). This document is subject
to the rights, licenses and restrictions contained in BCP 78, and
except as set forth therein, the authors retain all their rights.
Acknowledgment
Funding for the RFC Editor function is currently provided by the
Internet Society.
Meyer Expires February 23, 2006 [Page 13]
Html markup produced by rfcmarkup 1.129d, available from
https://tools.ietf.org/tools/rfcmarkup/