[Docs] [txt|pdf|xml] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 04 05 06 07 08 RFC 8004

Network Working Group                                        J. Laganier
Internet-Draft                                          Juniper Networks
Obsoletes: 5204 (if approved)                                  L. Eggert
Intended status: Standards Track                                   Nokia
Expires: September 15, 2011                               March 14, 2011


           Host Identity Protocol (HIP) Rendezvous Extension
                     draft-ietf-hip-rfc5204-bis-01

Abstract

   This document defines a rendezvous extension for the Host Identity
   Protocol (HIP).  The rendezvous extension extends HIP and the HIP
   registration extension for initiating communication between HIP nodes
   via HIP rendezvous servers.  Rendezvous servers improve reachability
   and operation when HIP nodes are multi-homed or mobile.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on September 15, 2011.

Copyright Notice

   Copyright (c) 2011 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as



Laganier & Eggert      Expires September 15, 2011               [Page 1]


Internet-Draft          HIP Rendezvous Extension              March 2011


   described in the Simplified BSD License.

Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
   2.  Terminology  . . . . . . . . . . . . . . . . . . . . . . . . .  3
   3.  Overview of Rendezvous Server Operation  . . . . . . . . . . .  4
     3.1.  Diagram Notation . . . . . . . . . . . . . . . . . . . . .  5
     3.2.  Rendezvous Client Registration . . . . . . . . . . . . . .  5
     3.3.  Relaying the Base Exchange . . . . . . . . . . . . . . . .  6
   4.  Rendezvous Server Extensions . . . . . . . . . . . . . . . . .  7
     4.1.  RENDEZVOUS Registration Type . . . . . . . . . . . . . . .  7
     4.2.  Parameter Formats and Processing . . . . . . . . . . . . .  8
       4.2.1.  RVS_HMAC Parameter . . . . . . . . . . . . . . . . . .  8
       4.2.2.  FROM Parameter . . . . . . . . . . . . . . . . . . . .  9
       4.2.3.  VIA_RVS Parameter  . . . . . . . . . . . . . . . . . . 10
     4.3.  Modified Packets Processing  . . . . . . . . . . . . . . . 10
       4.3.1.  Processing Outgoing I1 Packets . . . . . . . . . . . . 10
       4.3.2.  Processing Incoming I1 Packets . . . . . . . . . . . . 11
       4.3.3.  Processing Outgoing R1 Packets . . . . . . . . . . . . 11
       4.3.4.  Processing Incoming R1 Packets . . . . . . . . . . . . 11
   5.  Security Considerations  . . . . . . . . . . . . . . . . . . . 12
   6.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 12
   7.  Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . . 13
   8.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 13
     8.1.  Normative References . . . . . . . . . . . . . . . . . . . 13
     8.2.  Informative References . . . . . . . . . . . . . . . . . . 14
   Appendix A.  Changes from RFC 5204 . . . . . . . . . . . . . . . . 14























Laganier & Eggert      Expires September 15, 2011               [Page 2]


Internet-Draft          HIP Rendezvous Extension              March 2011


1.  Introduction

   The Host Identity Protocol (HIP) Architecture [RFC4423] introduces
   the rendezvous mechanism to help a HIP node to contact a frequently
   moving HIP node.  The rendezvous mechanism involves a third party,
   the rendezvous server (RVS), which serves as an initial contact point
   ("rendezvous point") for its clients.  The clients of an RVS are HIP
   nodes that use the HIP Registration Extension
   [I-D.ietf-hip-rfc5203-bis] to register their HIT->IP address mappings
   with the RVS.  After this registration, other HIP nodes can initiate
   a base exchange using the IP address of the RVS instead of the
   current IP address of the node they attempt to contact.  Essentially,
   the clients of an RVS become reachable at the RVS's IP address.
   Peers can initiate a HIP base exchange with the IP address of the
   RVS, which will relay this initial communication such that the base
   exchange may successfully complete.

2.  Terminology

   This section defines terms used throughout the remainder of this
   specification.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].

   In addition to the terminology defined in the HIP specification
   [I-D.ietf-hip-rfc5201-bis] and the HIP Registration Extension
   [I-D.ietf-hip-rfc5203-bis], this document defines and uses the
   following terms:

   Rendezvous Service
      A HIP service provided by a rendezvous server to its rendezvous
      clients.  The rendezvous server offers to relay some of the
      arriving base exchange packets between the initiator and
      responder.

   Rendezvous Server (RVS)
      A HIP registrar providing rendezvous service.

   Rendezvous Client
      A HIP requester that has registered for rendezvous service at a
      rendezvous server.

   Rendezvous Registration
      A HIP registration for rendezvous service, established between a
      rendezvous server and a rendezvous client.




Laganier & Eggert      Expires September 15, 2011               [Page 3]


Internet-Draft          HIP Rendezvous Extension              March 2011


3.  Overview of Rendezvous Server Operation

   Figure 1 shows a simple HIP base exchange without a rendezvous
   server, in which the initiator initiates the exchange directly with
   the responder by sending an I1 packet to the responder's IP address,
   as per the HIP specification [I-D.ietf-hip-rfc5201-bis].

                       +-----+                +-----+
                       |     |-------I1------>|     |
                       |  I  |<------R1-------|  R  |
                       |     |-------I2------>|     |
                       |     |<------R2-------|     |
                       +-----+                +-----+

          Figure 1: HIP base exchange without rendezvous server.

   The End-Host Mobility and Multihoming with the  Host Identity
   Protocol specification [I-D.ietf-hip-rfc5206-bis] allows a HIP node
   to notify its peers about changes in its set of IP addresses.  This
   specification presumes initial reachability of the two nodes with
   respect to each other.

   However, such a HIP node MAY also want to be reachable to other
   future correspondent peers that are unaware of its location change.
   The HIP Architecture [RFC4423] introduces rendezvous servers with
   whom a HIP node MAY register its host identity tags (HITs) and
   current IP addresses.  An RVS relays HIP packets arriving for these
   HITs to the node's registered IP addresses.  When a HIP node has
   registered with an RVS, it SHOULD record the IP address of its RVS in
   its DNS record, using the HIP DNS resource record type defined in the
   HIP DNS Extension [I-D.ietf-hip-rfc5205-bis].

                                   +-----+
                          +--I1--->| RVS |---I1--+
                          |        +-----+       |
                          |                      v
                       +-----+                +-----+
                       |     |<------R1-------|     |
                       |  I  |-------I2------>|  R  |
                       |     |<------R2-------|     |
                       +-----+                +-----+

           Figure 2: HIP base exchange with a rendezvous server.

   Figure 2 shows a HIP base exchange involving a rendezvous server.  It
   is assumed that HIP node R previously registered its HITs and current
   IP addresses with the RVS, using the HIP Registration Extension
   [I-D.ietf-hip-rfc5203-bis].  When the initiator I tries to establish



Laganier & Eggert      Expires September 15, 2011               [Page 4]


Internet-Draft          HIP Rendezvous Extension              March 2011


   contact with the responder R, it must send the I1 of the base
   exchange either to one of R's IP addresses (if known via DNS or other
   means) or to one of R's rendezvous servers.  Here, I obtains the IP
   address of R's rendezvous server from R's DNS record and then sends
   the I1 packet of the HIP base exchange to RVS.  RVS, noticing that
   the HIT contained in the arriving I1 packet is not one of its own,
   MUST check its current registrations to determine if it needs to
   relay the packets.  Here, it determines that the HIT belongs to R and
   then relays the I1 packet to the registered IP address.  R then
   completes the base exchange without further assistance from RVS by
   sending an R1 directly to the I's IP address, as obtained from the I1
   packet.  In this specification, the client of the RVS is always the
   responder.  However, there might be reasons to allow a client to
   initiate a base exchange through its own RVS, like NAT and firewall
   traversal.  This specification does not address such scenarios, which
   should be specified in other documents.

3.1.  Diagram Notation

  Notation       Significance
  --------       ------------

  I, R           I and R are the respective source and destination IP
                 addresses in the IP header.

  HIT-I, HIT-R   HIT-I and HIT-R are the initiator's and the
                 responder's HITs in the packet, respectively.

  REG_REQ        A REG_REQUEST parameter is present in the HIP header.

  REG_RES        A REG_RESPONSE parameter is present in the HIP header.

  FROM:I         A FROM parameter containing the IP address I is
                 present in the HIP header.

  RVS_HMAC       An RVS_HMAC parameter containing an HMAC keyed with the
                 appropriate registration key is present in the HIP
                 header.

  VIA:RVS        A VIA_RVS parameter containing the IP address RVS of a
                 rendezvous server is present in the HIP header.

3.2.  Rendezvous Client Registration

   Before a rendezvous server starts to relay HIP packets to a
   rendezvous client, the rendezvous client needs to register with it to
   receive rendezvous service by using the HIP Registration Extension
   [I-D.ietf-hip-rfc5203-bis] as illustrated in the following schema:



Laganier & Eggert      Expires September 15, 2011               [Page 5]


Internet-Draft          HIP Rendezvous Extension              March 2011


                 +-----+                            +-----+
                 |     |            I1              |     |
                 |     |--------------------------->|     |
                 |     |<---------------------------|     |
                 |  I  |         R1(REG_INFO)       | RVS |
                 |     |         I2(REG_REQ)        |     |
                 |     |--------------------------->|     |
                 |     |<---------------------------|     |
                 |     |         R2(REG_RES)        |     |
                 +-----+                            +-----+

          Rendezvous client registering with a rendezvous server.

3.3.  Relaying the Base Exchange

   If a HIP node and one of its rendezvous servers have a rendezvous
   registration, the rendezvous servers relay inbound I1 packets (that
   contain one of the client's HITs) by rewriting the IP header.  They
   replace the destination IP address of the I1 packet with one of the
   IP addresses of the owner of the HIT, i.e., the rendezvous client.
   They MUST also recompute the IP checksum accordingly.

   Because of egress filtering on the path from the RVS to the client
   [RFC2827][RFC3013], a HIP rendezvous server SHOULD replace the source
   IP address, i.e., the IP address of I, with one of its own IP
   addresses.  The replacement IP address SHOULD be chosen according to
   relevant IPv4 and IPv6 specifications [RFC1122][RFC3484].  Because
   this replacement conceals the initiator's IP address, the RVS MUST
   append a FROM parameter containing the original source IP address of
   the packet.  This FROM parameter MUST be integrity protected by an
   RVS_HMAC keyed with the corresponding rendezvous registration
   integrity key [I-D.ietf-hip-rfc5203-bis].



















Laganier & Eggert      Expires September 15, 2011               [Page 6]


Internet-Draft          HIP Rendezvous Extension              March 2011


                                               I1(RVS, R, HIT-I, HIT-R
         I1(I, RVS, HIT-I, HIT-R) +---------+     FROM:I, RVS_HMAC)
         +----------------------->|         |--------------------+
         |                        |   RVS   |                    |
         |                        |         |                    |
         |                        +---------+                    |
         |                                                       V
        +-----+        R1(R, I, HIT-R, HIT-I, VIA:RVS)       +-----+
        |     |<---------------------------------------------|     |
        |     |                                              |     |
        |  I  |            I2(I, R, HIT-I, HIT-R)            |  R  |
        |     |--------------------------------------------->|     |
        |     |<---------------------------------------------|     |
        +-----+             R2(R, I, HIT-R, HIT-I)           +-----+

                 Rendezvous server rewriting IP addresses.

   This modification of HIP packets at a rendezvous server can be
   problematic because the HIP protocol uses integrity checks.  Because
   the I1 does not include HMAC or SIGNATURE parameters, these two end-
   to-end integrity checks are unaffected by the operation of rendezvous
   servers.

   The RVS SHOULD verify the checksum field of an I1 packet before doing
   any modifications.  After modification, it MUST recompute the
   checksum field using the updated HIP header, which possibly included
   new FROM and RVS_HMAC parameters, and a pseudo-header containing the
   updated source and destination IP addresses.  This enables the
   responder to validate the checksum of the I1 packet "as is", without
   having to parse any FROM parameters.

4.  Rendezvous Server Extensions

   This section describes extensions to the HIP Registration Extension
   [I-D.ietf-hip-rfc5203-bis], allowing a HIP node to register with a
   rendezvous server for rendezvous service and notify the RVS aware of
   changes to its current location.  It also describes an extension to
   the HIP specification [I-D.ietf-hip-rfc5201-bis] itself, allowing
   establishment of HIP associations via one or more HIP rendezvous
   server(s).

4.1.  RENDEZVOUS Registration Type

   This specification defines an additional registration for the HIP
   Registration Extension [I-D.ietf-hip-rfc5203-bis] that allows
   registering with a rendezvous server for rendezvous service.





Laganier & Eggert      Expires September 15, 2011               [Page 7]


Internet-Draft          HIP Rendezvous Extension              March 2011


   Number   Registration Type
   ------   -----------------
   1        RENDEZVOUS

4.2.  Parameter Formats and Processing

4.2.1.  RVS_HMAC Parameter

   The RVS_HMAC is a non-critical parameter whose only difference with
   the HMAC parameter defined in the HIP specification
   [I-D.ietf-hip-rfc5201-bis] is its "type" code.  This change causes it
   to be located after the FROM parameter (as opposed to the HMAC):

 Type        65500
 Length      Variable.  Length in octets, excluding Type, Length, and
             Padding.
 HMAC        HMAC computed over the HIP packet, excluding the
             RVS_HMAC parameter and any following parameters. The
             HMAC is keyed with the appropriate HIP integrity key
             (HIP-lg or HIP-gl) established when rendezvous
             registration happened. The HIP "checksum" field MUST be set
             to zero, and the HIP header length in the HIP common header
             MUST be calculated not to cover any excluded parameter
             when the HMAC is calculated.  The size of the
             HMAC is the natural size of the hash computation
             output depending on the used hash function.

   To allow a rendezvous client and its RVS to verify the integrity of
   packets flowing between them, both SHOULD protect packets with an
   added RVS_HMAC parameter keyed with the HIP-lg or HIP-gl integrity
   key established while registration occurred.  A valid RVS_HMAC SHOULD
   be present on every packet flowing between a client and a server and
   MUST be present when a FROM parameter is processed.


















Laganier & Eggert      Expires September 15, 2011               [Page 8]


Internet-Draft          HIP Rendezvous Extension              March 2011


4.2.2.  FROM Parameter

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |             Type              |             Length            |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                                                               |
    |                             Address                           |
    |                                                               |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

    Type        65498
    Length      16
    Address     An IPv6 address or an IPv4-in-IPv6 format IPv4 address.

   A rendezvous server MUST add a FROM parameter containing the original
   source IP address of a HIP packet whenever the source IP address in
   the IP header is rewritten.  If one or more FROM parameters are
   already present, the new FROM parameter MUST be appended after the
   existing ones.

   Whenever an RVS inserts a FROM parameter, it MUST insert an RVS_HMAC
   protecting the packet integrity, especially the IP address included
   in the FROM parameter.

























Laganier & Eggert      Expires September 15, 2011               [Page 9]


Internet-Draft          HIP Rendezvous Extension              March 2011


4.2.3.  VIA_RVS Parameter

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |             Type              |             Length            |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                                                               |
    |                            Address                            |
    |                                                               |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    .                               .                               .
    .                               .                               .
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                                                               |
    |                            Address                            |
    |                                                               |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

    Type        65502
    Length      Variable
    Address     An IPv6 address or an IPv4-in-IPv6 format IPv4 address.

   After the responder receives a relayed I1 packet, it can begin to
   send HIP packets addressed to the initiator's IP address, without
   further assistance from an RVS.  For debugging purposes, it MAY
   include a subset of the IP addresses of its RVSs in some of these
   packets.  When a responder does so, it MUST append a newly created
   VIA_RVS parameter at the end of the HIP packet.  The main goal of
   using the VIA_RVS parameter is to allow operators to diagnose
   possible issues encountered while establishing a HIP association via
   an RVS.

4.3.  Modified Packets Processing

   The following subsections describe the differences of processing of
   I1 and R1 while a rendezvous server is involved in the base exchange.

4.3.1.  Processing Outgoing I1 Packets

   An initiator SHOULD NOT send an opportunistic I1 with a NULL
   destination HIT to an IP address that is known to be a rendezvous
   server address, unless it wants to establish a HIP association with
   the rendezvous server itself and does not know its HIT.





Laganier & Eggert      Expires September 15, 2011              [Page 10]


Internet-Draft          HIP Rendezvous Extension              March 2011


   When an RVS rewrites the source IP address of an I1 packet due to
   egress filtering, it MUST add a FROM parameter to the I1 that
   contains the initiator's source IP address.  This FROM parameter MUST
   be protected by an RVS_HMAC keyed with the integrity key established
   at rendezvous registration.

4.3.2.  Processing Incoming I1 Packets

   When a rendezvous server receives an I1 whose destination HIT is not
   its own, it consults its registration database to find a registration
   for the rendezvous service established by the HIT owner.  If it finds
   an appropriate registration, it relays the packet to the registered
   IP address.  If it does not find an appropriate registration, it
   drops the packet.

   A rendezvous server SHOULD interpret any incoming opportunistic I1
   (i.e., an I1 with a NULL destination HIT) as an I1 addressed to
   itself and SHOULD NOT attempt to relay it to one of its clients.

   When a rendezvous client receives an I1, it MUST validate any present
   RVS_HMAC parameter.  If the RVS_HMAC cannot be verified, the packet
   SHOULD be dropped.  If the RVS_HMAC cannot be verified and a FROM
   parameter is present, the packet MUST be dropped.

   A rendezvous client acting as responder SHOULD drop opportunistic I1s
   that include a FROM parameter, because this indicates that the I1 has
   been relayed.

4.3.3.  Processing Outgoing R1 Packets

   When a responder replies to an I1 relayed via an RVS, it MUST append
   to the regular R1 header a VIA_RVS parameter containing the IP
   addresses of the traversed RVSs.

4.3.4.  Processing Incoming R1 Packets

   The HIP specification [I-D.ietf-hip-rfc5201-bis] mandates that a
   system receiving an R1 MUST first check to see if it has sent an I1
   to the originator of the R1 (i.e., the system is in state I1-SENT).
   When the R1 is replying to a relayed I1, this check SHOULD be based
   on HITs only.  In case the IP addresses are also checked, then the
   source IP address MUST be checked against the IP address included in
   the VIA_RVS parameter.








Laganier & Eggert      Expires September 15, 2011              [Page 11]


Internet-Draft          HIP Rendezvous Extension              March 2011


5.  Security Considerations

   This section discusses the known threats introduced by these HIP
   extensions and the implications on the overall security of HIP.  In
   particular, it argues that the extensions described in this document
   do not introduce additional threats to the Host Identity Protocol.

   It is difficult to encompass the whole scope of threats introduced by
   rendezvous servers because their presence has implications both at
   the IP and HIP layers.  In particular, these extensions might allow
   for redirection, amplification, and reflection attacks at the IP
   layer, as well as attacks on the HIP layer itself, for example, man-
   in-the-middle attacks against the HIP base exchange.

   If an initiator has a priori knowledge of the responder's host
   identity when it first contacts the responder via an RVS, it has a
   means to verify the signatures in the HIP base exchange, which
   protects against man-in-the-middle attacks.

   If an initiator does not have a priori knowledge of the responder's
   host identity (so-called "opportunistic initiators"), it is almost
   impossible to defend the HIP exchange against these attacks, because
   the public keys exchanged cannot be authenticated.  The only approach
   would be to mitigate hijacking threats on HIP state by requiring an
   R1 answering an opportunistic I1 to come from the same IP address
   that originally sent the I1.  This procedure retains a level of
   security that is equivalent to what exists in the Internet today.

   However, for reasons of simplicity, this specification does not allow
   the establishment of a HIP association via a rendezvous server in an
   opportunistic manner.

6.  IANA Considerations

   This section is to be interpreted according to the Guidelines for
   Writing an IANA Considerations Section in RFCs [RFC2434].

   This document updates the IANA Registry for HIP Parameters Types by
   assigning new HIP Parameter Types values for the new HIP Parameters
   defined in Section 4.2:

   o  RVS_HMAC (defined in Section 4.2.1)

   o  FROM (defined in Section 4.2.2)

   o  VIA_RVS (defined in Section 4.2.3)





Laganier & Eggert      Expires September 15, 2011              [Page 12]


Internet-Draft          HIP Rendezvous Extension              March 2011


   This document defines an additional registration for the HIP
   Registration Extension [I-D.ietf-hip-rfc5203-bis] that allows
   registering with a rendezvous server for rendezvous service.

   Number   Registration Type
   ------   -----------------
   1        RENDEZVOUS

7.  Acknowledgments

   The following people have provided thoughtful and helpful discussions
   and/or suggestions that have improved this document: Marcus Brunner,
   Tom Henderson, Miika Komu, Mika Kousa, Pekka Nikander, Justino
   Santos, Simon Schuetz, Tim Shepard, Kristian Slavov, Martin
   Stiemerling, and Juergen Quittek.

8.  References

8.1.  Normative References

   [I-D.ietf-hip-rfc5201-bis]  Moskowitz, R., Heer, T., Jokela, P., and
                               T. Henderson, "Host Identity Protocol
                               Version 2 (HIPv2)",
                               draft-ietf-hip-rfc5201-bis-05 (work in
                               progress), March 2011.

   [I-D.ietf-hip-rfc5203-bis]  Laganier, J., Koponen, T., and L. Eggert,
                               "Host Identity Protocol (HIP)
                               Registration Extension",
                               draft-ietf-hip-rfc5203-bis-00 (work in
                               progress), August 2010.

   [I-D.ietf-hip-rfc5205-bis]  Laganier, J., "Host Identity Protocol
                               (HIP) Domain Name System (DNS)
                               Extension", draft-ietf-hip-rfc5205-bis-00
                               (work in progress), August 2010.

   [RFC1122]                   Braden, R., "Requirements for Internet
                               Hosts - Communication Layers", STD 3,
                               RFC 1122, October 1989.

   [RFC2119]                   Bradner, S., "Key words for use in RFCs
                               to Indicate Requirement Levels", BCP 14,
                               RFC 2119, March 1997.

   [RFC2434]                   Narten, T. and H. Alvestrand, "Guidelines
                               for Writing an IANA Considerations
                               Section in RFCs", BCP 26, RFC 2434,



Laganier & Eggert      Expires September 15, 2011              [Page 13]


Internet-Draft          HIP Rendezvous Extension              March 2011


                               October 1998.

   [RFC3484]                   Draves, R., "Default Address Selection
                               for Internet Protocol version 6 (IPv6)",
                               RFC 3484, February 2003.

8.2.  Informative References

   [I-D.ietf-hip-rfc5206-bis]  Nikander, P., Henderson, T., Vogt, C.,
                               and J. Arkko, "Host Mobility with the
                               Host Identity Protocol",
                               draft-ietf-hip-rfc5206-bis-01 (work in
                               progress), October 2010.

   [RFC2827]                   Ferguson, P. and D. Senie, "Network
                               Ingress Filtering: Defeating Denial of
                               Service Attacks which employ IP Source
                               Address Spoofing", BCP 38, RFC 2827,
                               May 2000.

   [RFC3013]                   Killalea, T., "Recommended Internet
                               Service Provider Security Services and
                               Procedures", BCP 46, RFC 3013,
                               November 2000.

   [RFC4423]                   Moskowitz, R. and P. Nikander, "Host
                               Identity Protocol (HIP) Architecture",
                               RFC 4423, May 2006.

Appendix A.  Changes from RFC 5204

   o  Updated HIP references to revised HIP specifications.

Authors' Addresses

   Julien Laganier
   Juniper Networks
   1094 North Mathilda Avenue
   Sunnyvale, CA  94089
   USA

   Phone: +1 408 936 0385
   EMail: julien.ietf@gmail.com








Laganier & Eggert      Expires September 15, 2011              [Page 14]


Internet-Draft          HIP Rendezvous Extension              March 2011


   Lars Eggert
   Nokia Research Center
   P.O. Box 407
   Nokia Group  00045
   Finland

   Phone: +358 50 48 24461
   EMail: lars.eggert@nokia.com
   URI:   http://research.nokia.com/people/lars_eggert/










































Laganier & Eggert      Expires September 15, 2011              [Page 15]


Html markup produced by rfcmarkup 1.129c, available from https://tools.ietf.org/tools/rfcmarkup/