[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 04 05 RFC 2226

Internet-Draft                                          Timothy J. Smith
                                                         IBM Corporation
                                                      Grenville Armitage
                                                     Lucent Technologies
                                                        October 14, 1997


                     IP Broadcast over ATM Networks
                     <draft-ietf-ion-bcast-05.txt>


Status of this Memo

   This document was submitted to the IETF Internetworking Over NBMA
   Working Group (ion).  Publication of this document does not imply
   acceptance by the Internetworking Over NBMA Working Group of any
   ideas expressed within.  Comments should be submitted to the
   ion@nexen.com mailing list.

   Distribution of this memo is unlimited.

   This memo is an internet draft. Internet Drafts are working documents
   of the Internet Engineering Task Force (IETF), its Areas, and its
   Working Groups. Note that other groups may also distribute working
   documents as Internet Drafts.

   To learn the current status of any Internet-Draft, please check the
   "lid-abstracts.txt" listing contained in the Internet-Drafts shadow
   directories on ds.internic.net (US East Coast), nic.nordu.net
   (Europe), ftp.isi.edu (US West Coast), or munnari.oz.au (Pacific
   Rim).

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED",  "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119.

Abstract

   This memo describes how the IP multicast service being developed by
   the IP over ATM working group may be used to support IP broadcast
   transmission. The solution revolves around treating the broadcast
   problem as a special case of multicast, where every host in the
   subnet or cluster is a member of the group.

   An understanding of the services provided by RFC 2022 is assumed.






Smith, Armitage          Expires April 14, 1998                 [Page 1]


Internet Draft                                          October 14, 1997


1.  Introduction.


   The IETF's first step in solving the problems of running IP over
   Asynchronous Transfer Mode (ATM) technology is described in RFC 1577
   [1].  It provides for unicast communication between hosts and routers
   within Logical IP Subnets (LISs), and proposes a centralized ATM ARP
   Server which provides IP to ATM address resolution services to LIS
   members.

   Two classes of IP service were omitted - multicast and broadcast
   transmissions. Multicasting allows a single transmit operation to
   cause a packet to be received by multiple remote destinations.
   Broadcasting typically allows a single transmit operation to cause a
   packet to be received by all IP hosts that are members of a
   particular 'subnet'.

   To address the need for multicast support (represented by
   transmission to IP addresses in the Class D space), RFC 2022
   ("Support for Multicast over UNI 3.0/3.1 based ATM Networks") [2] was
   created.  This draft creates an analog of the RFC 1577 ARP Server - a
   new entity known as the MARS (Multicast Address Resolution Server).
   The MARS operates as a centralized registry and distribution
   mechanism for mappings between IP multicast addresses and groups of
   ATM unicast addresses. Host behavior is also defined for establishing
   and managing point to multipoint VCs, based on the information
   returned by the MARS, when hosts wish to transmit packets to a
   multicast group.

   This memo aims to show how RFC 2022 may be used to emulate IP
   broadcast within Logical IP Subnets. While the broadcast technique
   does not align itself well with the underlying point-to-point nature
   of ATM, clearly, some applications will still wish to use IP
   broadcasts.  Client-server applications where the client searches for
   a server by sending out a broadcast is one scenario.  Routing
   protocols, most notably RIP, are other examples.


2.  Review of Unicast and Multicast.

   Both the unicast and multicast cases take advantage of the point-to-
   point and point-to-multipoint capabilities defined in the ATM Forum
   UNI 3.1 document [4].  A unicast IP address has a single ATM level
   destination.  Unicast transmissions occur over point to point Virtual
   Channels (VCs) between the source and destination. The ARP Server
   holds mappings between IP destination addresses and their associated
   ATM destination address. Hosts issue an ARP_REQUEST to the ARP Server
   when they wish to ascertain a particular mapping.  The ARP Server



Smith, Armitage          Expires April 14, 1998                 [Page 2]


Internet Draft                                          October 14, 1997


   replies with either an ARP_REPLY containing the ATM address of the
   destination, or an ARP_NAK when the ARP Server is unable to resolve
   the address. If the request is successful the host establishes a VC
   to the destination interface. This VC is then used to forward the
   first (and subsequent) packets to that particular IP destination. RFC
   1577 describes in further detail how hosts are administratively
   grouped in to Logical IP Subnets (LISs), and how the ARP Server
   establishes the initial mappings for members of the LIS it serves.

   The basic host behavior for multicasting is similar - the sender must
   establish and manage a point to multipoint VC whose leaf nodes are
   the group's actual members. Under UNI 3.1 these VCs can only be
   established and altered by the source (root) interface.

   The MARS is an evolution of the ARP Server model, and performs two
   key functions.  The first function is the maintenance of a list of
   ATM addresses corresponding to the members for each group.  This list
   is created by a host registration process which involves two messages
   - a MARS_JOIN which declares that a host wishes to join the specified
   group(s), and a MARS_LEAVE which indicates that a host wishes to
   leave the specified group(s).

   MARS_JOIN and MARS_LEAVE messages are also redistributed to all
   members of the group so that active senders may dynamically adjust
   their point to multipoint VCs accordingly.

   The other major function is the retrieval of group membership from
   MARS (analogous to the ARP Server providing unicast address
   mappings). When faced with the need to transmit an IP packet with a
   Class D destination address, a host issues a MARS_REQUEST to the
   MARS. If the group has members the MARS returns a MARS_MULTI
   (possibly in multiple segments) carrying a set of ATM addresses. The
   host then establishes an initial point to multipoint VC using these
   ATM addresses as the leaf nodes. If the MARS had no mapping it would
   return a MARS_NAK.

   (RFC 2022 also discusses how the MARS can arrange for Class D groups
   to be supported by either multicast servers, or meshes of point to
   multipoint VCs from host to host.  However, from the host's
   perspective this is transparent, and is not central to this
   discussion of IP broadcast support.)

   This memo describes how a host may utilize the registration and group
   management functions in an existing MARS based IP/ATM network to
   emulate IP broadcasts.






Smith, Armitage          Expires April 14, 1998                 [Page 3]


Internet Draft                                          October 14, 1997


3.  Broadcast as a special case of Multicast.

   Many of the problems that occur when implementing a broadcast
   solution also occur in when implementing a multicast solution.  In
   fact, broadcast may be considered a special case of multicast.  That
   is, broadcast is a multicast group whose members include all members
   in the LIS.

   There are two broadcast groups which this memo addresses:

      1) 255.255.255.255 - "All ones" broadcast

      2) x.z - CIDR-prefix (subnet) directed broadcast

   Broadcast (1) is sometimes referred to as a limited broadcast to this
   physical network.  Broadcast (2) can be thought of as the the
   broadcast for subnets or networks in the old paradigm. As described
   in [6] and [7], the notion of subnets and networks is being replaced
   with a more efficient utilization of the routing address space known
   as Classless Inter-Domain Routing.  The CIDR-prefix (x) is the
   combination of IP address and subnet mask that denotes the subnet
   number.  The host portion of the address (z) is all ones.  One should
   note that while these broadcasts have different scopes at the IP or
   network layer, they have precisely the same scope at the link layer
   -- namely that all members of the LIS will receive a copy.

   These addresses may be used in two environments:

      o  Broadcasting to all members of a given LIS where
         a priori knowledge of a host's IP address and
         subnet mask are known (e.g. the CIDR-prefix directed
         broadcast).

      o  Broadcasting to all members of a physical network
         without knowledge of a host's IP address and
         subnet mask (e.g. the all ones broadcast).

   On a broadcast medium like Ethernet, these two environments result in
   the same physical destination.  That is, all stations on that network
   will receive the broadcast even if they are on different logical
   subnets, or are non-IP stations.  With ATM, this may not be the case.
   Because ATM is non-broadcast, a registration process must take place.
   And if there are stations that register to some broadcast groups, but
   not others, then the different broadcast groups will have different
   memberships.  The notion of broadcast becomes inconsistent.

   One case that requires the use of the all ones broadcast is that of
   the diskless boot, or bootp client, where the host boots up, and does



Smith, Armitage          Expires April 14, 1998                 [Page 4]


Internet Draft                                          October 14, 1997


   not know its own IP address or subnet mask.  Clearly, the host does
   not know which subnet it belongs to.   So, to send a broadcast to its
   bootp server, the diskless workstation must use the group which
   contains no subnet information, i.e. the 255.255.255.255 broadcast
   group.  Carrying the example a little further, the bootp server,
   after receiving the broadcast, can not send either a directed frame
   nor a subnet directed broadcast to respond to the diskless
   workstation.  Instead, the bootp server must also use the
   255.255.255.255 group to communicate with the client.

   While the all ones broadcast is required at the IP layer, it also has
   relevance at the link layer when deciding which broadcast group to
   register with in MARS.  In other words, a bootp client wishing to
   register for a link layer broadcast, can only register for
   255.255.255.255 in the MARS address space because the client's subnet
   is unknown at the time.  Given that some applications must use the
   all ones address in MARS for their broadcast group, and that we wish
   to minimize the number of broadcast groups used by LIS members, the
   all ones group in MARS MUST be used by all members of the LIS when
   registering to receive broadcast transmissions.  The VCC used for
   transmitting any broadcast packet will be based on the members
   registered in the MARS under the 255.255.255.255 address position.
   This VCC will be referred to as the "broadcast channel" through the
   remainder of this memo.


4.  The MARS role in broadcast.

   Many solutions have been proposed, some of which are listed in
   Appendix A.  This memo addresses a MARS solution which appears to do
   the best job of solving the broadcast problem.

   There are a number of characteristics of the MARS architecture that
   should be kept intact.  They include:

   o  MARS contains no knowledge of subnet prefixes and subnet masks.
      Each group address registered with MARS is managed independently.

   o  A MARS may only serve one LIS. This insures that the
      broadcast group 255.255.255.255 is joined by hosts from one
      LIS, keeping its scope bound to conventional interpretation.

   o  The Multicast Server (MCS) described in [2] may be used to service
      the broadcast groups defined in this memo without modification.
      The MCS will reduce the number of channels used by the network.

   The MARS needs no additional code or special algorithms to handle the
   resolution of IP broadcast addresses. It is simply a general database



Smith, Armitage          Expires April 14, 1998                 [Page 5]


Internet Draft                                          October 14, 1997


   that holds {Protocol address, ATM.1, ATM.2, ... ATM.n} mappings, and
   imposes no constraints on the type and length of the 'Protocol
   address'. Whether the hosts view it as Class D or 'broadcast' (or
   even IP) is purely a host side issue.

   It is likely that end points will want to use the IP broadcast
   emulation described here in order to support boot time location of
   the end point's IP address. This leads to the observation that the
   MARS should NOT expect to see both the IP source and ATM source
   address fields of the MARS_JOIN filled in.  This is reasonable, since
   only the ATM source address is used when registering the end point as
   a group member.

   The MARS architecture is sufficient to insure the integrity of the
   broadcast group list without any modification.


5.  Host Requirements for Broadcast.

   The following list of bullets describes additional characteristics of
   a MARS-compliant host.  These characteristics are required to take
   advantage of the broadcast function.

   o  A host must register as a MARS client.

   o  A host, soon after registration MUST issue a MARS_JOIN to the
      all ones broadcast address (i.e. 255.255.255.255) with the
      mar$flags.layer3grp reset.

   o  When transmitting packets, the host should map all IP layer
      broadcasts to the VCC (broadcast channel) created and maintained
      based on the all ones entry in MARS.

   o  A host MUST monitor the MARS_JOIN/MARS_LEAVE messages
      for 255.255.255.255 to keep the broadcast channel current.

   o  A broadcast channel should be torn down after a period of
      inactivity.  The corresponding timeout period MAY be specified
      with a minimum value of one minute, and a RECOMMENDED
      default value of 20 minutes.

   One should note that while every member participating in the
   broadcast MUST be a member of the all ones group, not all members
   will choose to transmit broadcast information.  Some members will
   only elect to receive broadcast information passively.  Therefore, in
   a LIS with n stations, there may be less than n channels terminated
   at each station for broadcast information.  Further reductions may be
   gained by adding a Multicast Server (MCS) to the broadcast



Smith, Armitage          Expires April 14, 1998                 [Page 6]


Internet Draft                                          October 14, 1997


   environment which could reduce the number of VCs to two (one
   incoming, one outgoing), or one for a station that only wishes to
   listen.

   It is well understood that broadcasting in this environment may tax
   the resources of the network and of the hosts that use it.
   Therefore, an implementer MAY choose to provide a mechanism for
   retracting the host's entry in the broadcast group after it has been
   established or prior to joining the group.  The MARS_LEAVE is used to
   request withdrawal from the group if the host wishes to disable
   broadcast reception after it has joined the group.  The default
   behavior SHALL be to join the all ones broadcast group in MARS.


6.  Implications of IP broadcast on ATM level resources.

   RFC 2022 discusses some of the implications of large multicast groups
   on the allocation of ATM level resources, both within the network and
   within end station ATM interfaces.

   The default mechanism is for IP multicasting to be achieved using
   meshes of point to multipoint VCs, direct from source host to group
   members. Under certain circumstances system administrators may, in a
   manner completely transparent to end hosts, redirect multicast
   traffic through ATM level Multicast Servers (MCSs). This may be
   performed on an individual group basis.

   It is sufficient to note here that the IP broadcast 'multicast group'
   will constitute the largest consumer of VCs within your ATM network
   when it is active. For this reason it will probably be the first
   multicast group to have one or more ATM MCSs assigned to support it.
   However, there is nothing unique about an MCS assigned to support IP
   broadcast traffic, so this will not be dealt with further in this
   memo. RFC 2022 contains further discussion on the possible
   application of multiple MCSs to provide fault-tolerant architectures.


7.  Further discussion.

   A point of discussion on the ip-atm forum revolved around "auto
   configuration" and "diskless boot".  This memo describes a broadcast
   solution that requires the use of the MARS.  Therefore, at a minimum,
   the ATM address of the MARS must be manually configured into a
   diskless workstation.  Suggestions such as universal channel numbers,
   and universal ATM addresses have been proposed, however, no agreement
   has been reached.

   Another topic for discussion is multiprotocol support.  MARS is



Smith, Armitage          Expires April 14, 1998                 [Page 7]


Internet Draft                                          October 14, 1997


   designed for protocol independence.  This memo specifically addresses
   the IP broadcast case, identifying which addresses are most effective
   in the IP address space.  However, the principles apply to any layer
   3 protocol.  Further work should be performed to identify suitable
   addresses for other layer 3 protocols.

   Finally, there has been support voiced for a link layer broadcast
   that would be independent of the layer 3 protocol.  Such a solution
   may provide a simpler set of rules through which broadcast
   applications may be used.  In addition, some solutions also provide
   for more efficient use of VCCs.


Security Considerations

   This memo addresses a specific use of the MARS architecture and
   components to provide the broadcast function.  As such, the security
   implications are no greater or less than the implications of using
   any of the other multicast groups available in the multicast address
   range.  Should enhancements to security be required, they would need
   to be added as an extension to the base architecture in RFC 2022.


Acknowledgments

   The apparent simplicity of this memo owes a lot to the services
   provided in [2], which itself is the product of much discussion on
   the IETF's IP-ATM working group mailing list.  Grenville Armitage
   worked on this document while at Bellcore.






















Smith, Armitage          Expires April 14, 1998                 [Page 8]


Internet Draft                                          October 14, 1997


References

   [1]  Laubach, M., "Classical IP and ARP over ATM", RFC 1577,
   Hewlett-Packard Laboratories, December 1993.

   [2]  Armitage, G., "Support for Multicast over UNI 3.0/3.1 based ATM
   Networks", RFC 2022, November 1995.

   [3]  Deering, S., "Host Extensions for IP Multicasting", RFC 1112,
   Stanford University, August 1989.

   [4]  ATM Forum, "ATM User-Network Interface Specification Version
   3.0", Englewood Cliffs, NJ: Prentice Hall, September 1993.

   [5]  Perez, M., Liaw, F., Grossman, D., Mankin, A., Hoffman, E.,
   Malis, A., "ATM Signaling Support for IP over ATM", RFC 1755,
   February 1995.

   [6]  Fuller, V., Li, T., Yu, J., Varadhan, K., "Classless Inter-
   Domain Routing (CIDR): an Address Assignment and Aggregation
   Strategy", RFC 1519, September 1993.

   [7]  Baker, F., "Requirements for IP Version 4 Routers", RFC 1812,
   June 1995.


Author's Address

Timothy J. Smith
Network Routing Systems,
International Business Machines Corporation.
N21/664
P.O.Box 12195
Research Triangle Park, NC 27709

Phone: (919) 254-4723
EMail: tjsmith@vnet.ibm.com


Grenville Armitage
Bell Labs, Lucent Technologies.
101 Crawfords Corner Rd,
Holmdel, NJ, 07733
Email: gja@lucent.com







Smith, Armitage          Expires April 14, 1998                 [Page 9]


Internet Draft                                          October 14, 1997


Appendix A.  Broadcast alternatives

   Throughout the development of this memo, there have been
   a number of alternatives explored and discarded for one
   reason or another.  This appendix documents these alternatives
   and the reason that they were not chosen.


A.1  ARP Server Broadcast Solutions.

   The ARP Server is a good candidate to support broadcasting.  There
   is an ARP Server for every LIS.  The ARP Server contains the entire
   LIS membership.  These are fundamental ingredients for the broadcast
   function.


A.1.1  Base Solution without modifications to ARP Server.

   One may choose as an existing starting point to use only what is
   available in RFC 1577.  That is, a host can easily calculate the
   range of members in its LIS based on its own IP address and
   subnet mask.  The host can then issue an ARP Request for every
   member of the LIS.  With this information, the host can then
   set up point-to-point connections with all members, or can set
   up a point-to-multipoint connection to all members.  There you have
   it, the poor man's broadcast.

   While this solution is very straight forward, it suffers from a number
   of problems.

   o  The load on the ARP Server is very large.  If all stations on
      a LIS choose to implement broadcasting, the initial surge of
      ARP Requests will be huge.  Some sort of slow start sequence
      would be needed.

   o  The amount of resource required makes this a non-scalable
      solution.  The authors believe that broadcasting will require
      an MCS to reduce the number of channel resources
      required to support each broadcast 'group'.  Using the ARP
      Server in this manner does not allow an MCS
      to be transparently introduced. (Basic RFC1577 interfaces
      also do not implement the extended LLC/SNAP encapsulation
      required to safely use more than one MCS).

   o  The diskless boot solution can not function in this environment
      because it may be unable to determine which subnet to which
      it belongs.




Smith, Armitage          Expires April 14, 1998                [Page 10]


Internet Draft                                          October 14, 1997


A.1.2  Enhanced ARP Server solution.

   This solution is similar to the base solution except that it
   takes some of the (MARS) multicast solution and embeds it in the
   ARP Server.  The first enhancement is to add the MARS_MULTI
   command
   to the set of opcodes that the ARP Server supports.  This would
   allow a host to issue a single request, and to get back the
   list of members in one or more MARS_REPLY packets.  Rather
   than have a registration mechanism, the ARP Server could simply
   use the list of members that have already been registered.  When
   a request comes in for the subnet broadcast address,
   the ARP Server would aggregate the list, and
   send the results to the requester.

   This suffers from two drawbacks.

   1)  Scalability with regard to number of VCs is still an issue.
       One would eventually need to add in some sort of multicast
       server solution to the ARP Server.

   2)  The diskless boot scenario is still broken.  There is no
       way for a station to perform a MARS_MULTI without first
       knowing its IP address and subnet mask.

   The diskless boot problem could be solved by adding to the
   ARP Server a registration process where anyone could register
   to the 255.255.255.255 address.  These changes would make
   the ARP Server look more and more like MARS.


A.2  MARS Solutions.

   If we wish to keep the ARP Server constant as described in
   RFC 1577, the alternative is to use the Multicast Address
   Resolution Server (MARS) described in [2].

   MARS has three nice features for broadcasting.

   1)  It has a generalized registration approach which allows
       for any address to have a group of entities registered.
       So, if the subnet address is not known, a host can
       register for an address that is known (e.g. 255.255.255.255).

   2)  The command set allows for lists of members to be passed
       in a single MARS_MULTI packet.   This reduces traffic.

   3)  MARS contains an architecture for dealing with the



Smith, Armitage          Expires April 14, 1998                [Page 11]


Internet Draft                                          October 14, 1997


       scalability issues.  That is, Multicast Servers (MCSs)
       may be used to set up the point-to-multipoint channels
       and reduce the number of channels that a host needs to
       set up to one.  Hosts wishing to broadcast will instead
       send the packet to the MCS who will then forward it to
       all members of the LIS.


A.2.1.  CIDR-prefix (Subnet) Broadcast solution.

   One of the earliest solutions was to simply state that broadcast
   support would be implemented by using a single multicast group
   in the class D address space --
   namely, the CIDR-prefix (subnet) broadcast address group.  All
   members of a LIS would
   be required to register to this address, and use it as required.
   A host wishing to use either the 255.255.255.255 broadcast, or the
   network broadcast addresses would internally map the VC to the
   subnet broadcast VC.  The all ones and network broadcast addresses
   would exist on MARS, but would be unused.

   The problem with this approach goes back to the diskless workstation
   problem.  Because the workstation may not know which subnet it
   belongs to, it doesn't know which group to register with.


A.2.2.  All one's first, subnet broadcast second

   This solution acknowledges that the diskless boot problem requires
   a generic address (one that does not contain CIDR-prefix
   (subnet) information) to
   register with and to use until subnet knowledge is known.  In essence,
   all stations first register to the 255.255.255.255 group, then as
   they know their subnet information, they could optionally de-register
   from the all one's group and register to the CIDR-prefix (subnet)
   broadcast group.

   This solution would appear to solve a couple of problems:

   1)  The bootp client can function if the server remains
       registered to the all one's group continuously.

   2)  There will be less traffic using the all ones group
       because the preferred transactions will be on the
       subnet broadcast channel.

   Unfortunately the first bullet contains a flaw.  The
   server must continually be registered to two groups -- the all ones



Smith, Armitage          Expires April 14, 1998                [Page 12]


Internet Draft                                          October 14, 1997


   group and the subnet broadcast group.  If this server has multiple
   processes that are running different IP applications, it may be
   difficult for the link layer to know which broadcast VC to use.
   If it always uses the all ones, then it will be missing members
   that have removed themselves from the all ones and have registered
   to the subnet broadcast.  If it always uses the subnet broadcast
   group, the diskless boot scenario gets broken.  While making the
   decision at the link layer may require additional control flows
   be built into the path, it may also require the rewriting of
   application software.

   In some implementations, a simple constant is used to indicate
   to the link layer that this packet is to be transmitted to the
   broadcast "MAC" address.  The assumption is that the physical
   network broadcast and the logical protocol broadcast are one
   and the same.  As pointed out earlier, this is not the case
   with ATM.  Therefore applications would need to specifically
   identify the subnet broadcast group address to take advantage
   of the smaller group.

   These problems could be solved in a number of ways, but it was
   thought that they added unnecessarily to the complexity of the
   broadcast solution.




























Smith, Armitage          Expires April 14, 1998                [Page 13]


Internet Draft                                          October 14, 1997


Appendix B.  Should MARS Be Limited to a Single LIS?

   RFC 2022 explicitly states that a network administrator MUST
   ensure that each LIS is served by a separate MARS, creating
   a one-to-one mapping between cluster and a unicast LIS.
   But, it also mentions that relaxation of this restriction MAY
   occur after future research warrants it.  This appendix discusses
   some to the potential implications to broadcast should this
   restriction be removed.

   The most obvious change would be that the notion of a cluster
   would span more than one LIS.  Therefore, the broadcast group of
   255.255.255.255 would contain members from more than one LIS.

   It also should be emphasized that the one LIS limitation
   is not a restriction of the MARS architecture.  Rather,
   it is only enforced if an administrator chooses to do so.


































Smith, Armitage          Expires April 14, 1998                [Page 14]


Html markup produced by rfcmarkup 1.127, available from https://tools.ietf.org/tools/rfcmarkup/