[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 04 05 06 07 08 09 10

ipsp working group                                             Man Li
Internet Draft                                                  Nokia
Expires August 2002                                     David Arneson
                                                                   N/A
                                                            Avri Doria
                                                                   LTU
                                                           Jamie Jason
                                                                 Intel
                                                            Cliff Wang
                                                             SmartPipe
                                                       Markus Stenberg
                                                                   SSH


                                                        February 2002



                       IPsec Policy Information Base
                      draft-ietf-ipsp-ipsecpib-04.txt


Status of this Memo

   This document is an Internet-Draft and is in full conformance with
   all provisions of Section 10 of RFC2026 [1].

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups. Note that
   other groups may also distribute working documents as Internet-
   Drafts. Internet-Drafts are draft documents valid for a maximum of
   six months and may be updated, replaced, or obsoleted by other
   documents at any time. It is inappropriate to use Internet- Drafts
   as reference material or to cite them other than as "work in
   progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt
   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.


Abstract

   This document specifies a set of policy rule classes (PRC) for
   configuring IPsec policy at IPsec-enabled devices (e.g., security
   gateways). Instances of these classes reside in a virtual
   information store called the IPsec Policy Information Base (PIB).
   The COPS protocol [5] with extensions for provisioning [6] is used
   to transmit this IPsec policy information to IPsec-enabled
   devices. The PRCs defined in this IPsec PIB are intended for use
   by the COPS-PR IPsec client type. These PRCs are in addition to
   any other PIBs that may be defined for the IPsec client type, as
   well as the PRCs defined in the Framework PIB [9].

Li, et al                Expires August, 2002                       1
                    IPsec Policy Information Base      February, 2002




Conventions used in this document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
   NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED",  "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   RFC-2119 [2].


1. Introduction

   The policy rule classes (PRC) defined in this document contain
   parameters for IKE phase one and phase two negotiations. Details
   of these parameters can be found in [12], [10], [8], [3], [7],
   [11] and [14]. The PIB defined in this document is based on the
   IPsec configuration policy model [12]. The rule and role approach
   proposed in [13], which scales to large networks, is adopted for
   distributing IPsec policy over the COPS-PR protocol [6].


2. Operation Overview

   Following the policy framework convention [13], the management
   entity that downloads policy to IPsec-enabled devices will be
   called a Policy Decision Point (PDP) and the target IPsec-enabled
   devices will be called Policy Enforcement Points (PEP).

   After connecting to a PDP using COPS-PR, a PEP reports to the PDP
   the PIB Provisioning Classes (PRCs) it supports as well as any
   limitations related to the implementations of theses classes and
   parameters. The PEP provides the above information using the
   frwkPrcSupportTable and the frwkCompLimitsTable defined in the
   framework PIB [9]. In addition, the PEP also reports the interface
   type capabilities and role combinations it supports using the
   frwkIfCapSetTable and the frwkIfCapSetRoleComboTable. Each row of
   the frwkIfCapSetTable contains a capability set name and a
   reference to an instance of a PRC that describes the capabilities
   of the interface type. The capability instances may reside in the
   ipSecIfCapsTable or in a table defined in another PIB. Each row of
   the frwkIfCapSetRoleComboTable contains an interface capability
   set name and a role combination.

   Based on the interface capabilities and role combinations, the PDP
   provides the PEP with IPsec policy information. Later on, if any
   of the interface capabilities or role combinations of the PEP
   change, the PEP notifies the PDP. The PDP will then send a new set
   of IPsec policy information to the PEP. In addition, if the policy
   associated with a given interface capability and role combination
   changes, the PDP will deliver the new IPsec policy to all the PEPs
   that have registered with that interface capability and role
   combination.


   Li, et al            Expires August, 2002                        2
                    IPsec Policy Information Base      February, 2002


3. Structure of IPsec PIB

   An IPsec policy consists of an ordered list of IPsec rules. Each
   rule is composed of a set of conditions and a set of actions. If a
   packet matches any of the conditions, the actions will be applied
   accordingly.

   The IPsec PIB module consists of nine groups. The selector group
   describes conditions to be associated with IPsec rules. The IPsec
   association group, AH transform group, ESP transform group, COMP
   transform group, IKE association group and the credential group
   together describe actions to be associated with IPsec rules. The
   policy time period group specifies time periods during which a
   rule is valid. The interface capability group is used by a PEP to
   report the capabilities associated with its interface types.

3.1 IPsec association group

   This group specifies IPsec Security Associations.

   The ipSecRuleTable is the starting point for specifying an IPsec
   policy. It contains an ordered list of IPsec rules. Each rule is
   associated with IfName, Roles and Direction attributes to indicate
   the interface type and role combinations as well as the direction
   of the interface to which this rule is to be applied. Each rule
   points to a set of selectors and, optionally, a set of IPSO
   filters to indicate the conditions associated with this rule. In
   addition, each rule has a pointer to a set of actions to indicate
   the actions associated with this rule. Hence if a packet matches a
   selector in the selector set and, if the reference to the IPSO
   filter set is not zero, it matches a filter in the IPSO filter
   set, the action(s) associated with this rule will be applied to
   the packet.

   When a rule involves multiple actions, the ExecutionStrategy
   attribute indicates how these actions are executed. A value of
   ôDoAllö means that all the actions MUST be applied to the packet
   according to a predefined order. A value of ôDoUntilSuccessö means
   that the actions MUST be tried in sequence until a successful
   execution of a single action.

   For example, in a nested Security Associations case the actions of
   an initiator's rule might be structured as:

    ExecutionStrategy='Do All'
    |
    +---1--- IPsecTunnelAction    // set up SA from host to gateway
    |
    +---2--- IPsecTransportAction // set up SA from host through
                                  // tunnel to remote host




   Li, et al            Expires August, 2002                        3
                    IPsec Policy Information Base      February, 2002


   Another example, showing a rule with fallback actions might be
   structured as:

    ExecutionStrategy='Do Until Success'
    |
    +---1--- IPsecTunnelAction // set up SA from host to gateway [A]
    |
    +---2--- IPsecTunnelAction // set up SA from host to gateway [B]

   As an optional feature, IPsec associations may be established
   without being prompted by IP packets. The AutoStart attribute
   indicates if the IPsec association(s) of this rule should be set
   up automatically. Support of this attribute is optional.

   IPsec actions may be of two types: Static Action and Negotiation
   Action. Static Actions do not require any negotiations. They
   include by-pass, discard, IKE rejection, pre-configured transport
   and pre-configured tunnel actions. Negotiation Actions require
   negotiations in order to establish Security Associations. They
   include transport and tunnel actions.

   The ipSecActionSetTable specifies sets of actions. Actions within
   a set form an ordered list. If an action within a set is a Static
   Action, the ActionId MUST point to a valid instance in the
   ipSecStaticActionTable. If the action is a Negotiation Action, the
   ActionId MUST point to a valid instance in the
   ipSecNegotiationActionTable. For other actions, the ActionId MAY
   point to an instance of a PRC defined in some other PIB module.

   The ipSecStaticActionTable specifies IPsec Static Actions. For a
   pre-configured transport or pre-configured tunnel action, it
   further points to a valid instance in another table that describes
   a transform to be used, for example, the ipSecEspTransformTable.
   In addition, the SPI used for the transform is also defined in the
   table.

   The ipSecNegotiationActionTable specifies IPsec Negotiation
   Actions. It points to a valid instance in the
   ipSecAssociationTable that further defines the IPsec association
   to be established. For key exchange policy, the KeyExchangeId
   points to a valid instance in another table that describes key
   exchange procedures. If a single IKE phase one negotiation is used
   for the key exchange, this attribute MUST point to an instance in
   the ipSecIkeAssociationTable. If multiple IKE phase one
   negotiations (e.g., with different modes) are to be tried until
   success, this attribute SHOULD point to ipSecIkeRuleTable. For
   other key exchange methods, this attribute MAY point to an
   instance of a PRC defined in some other PIB module.

   The ipSecAssociationTable specifies attributes associated with
   IPsec associations. For each association, it points to a set of
   proposals in the ipSecProposalSetTable that is associated with
   this association.

   Li, et al            Expires August, 2002                        4
                    IPsec Policy Information Base      February, 2002



   The ipSecProposalSetTable specifies sets of proposals. Proposals
   within a set are ordered with a preference value.

   The ipSecProposalTable specifies proposals. It points to sets of
   ESP transforms, AH transforms and COMP transforms. Within a
   proposal, sets of transforms of different types are logically
   ANDed. Transforms of the same type within a transform set are to
   be logically ORed. For example, if the proposal were

      ESP = { (HMAC-MD5, 3DES), (HMAC-MD5, DES) }
      AH  = { MD5, SHA-1 }

   then the one sending the proposal would want the other side to
   pick one from the ESP transform (preferably (HMAC-MD5, 3DES)) list
   AND one from the AH transform list (preferably MD5).

3.2 AH, ESP and COMP transform groups

   The AH, ESP and COMP transform groups describe sets of AH, ESP and
   COMP transforms respectively.

3.3 IKE association group

   This group specifies rules associated with IKE phase one
   negotiation.

   The ipSecIkeRuleTable and the ipSecIkeActionSetTable are optional
   tables. Support of these tables is required only when a policy
   contains:

   - Multiple IKE phase one actions (e.g., with different exchange
   modes) that are associated with one IPsec association. These
   actions are to be tried in sequence till one success.

   - IKE phase one actions that start automatically.

   For the latter case, IKE rules may be distributed independently
   and the IfName and Roles attributes in the ipSecIkeRuleTable
   indicate the interface type and role combinations to which this
   rule is to be applied.

   The ipSecIkeActionSetTable specifies sets of actions. Actions
   within a set form an ordered list.

   The ipSecIkeAssociationTable contains parameters associated with
   IKE associations including the IKE identities to be used during
   IKE phase one negotiation. It points to a set of credentials
   specified in the ipSecCredentialTable. Any of the credentials in
   this set may be used during IKE phase one negotiation. In
   addition, each IKE association points to a set of IKE proposals to
   be associated with this association. If the Authentication Method
   for one or more of the IKE proposals is specified as PresharedKey

   Li, et al            Expires August, 2002                        5
                    IPsec Policy Information Base      February, 2002


   in the ipSecIkeProposalTable, the ipSecIkeAssociationPresharedKey
   attribute contains the actual pre-shared key to be used for the
   proposal(s). This attribute is optional. If this attribute is not
   supported or contains a zero length octet, the pre-shared key MUST
   be obtained through other methods.

   The ipSecIkeProposalSetTable specifies sets of proposals.
   Proposals within a set are ordered with a preference value.The
   ipSecIkeProposalTable contains parameters associated with IKE
   proposals.

   The ipSecIkePeerEndpointTable specifies IKE peer endpoint
   information that includes acceptable peer identity and credentials
   for IKE phase one negotiation. It points to a set of credentials
   specified in the ipSecIkePeerEndpointCredentialSetTable. Any of
   the credentials in the set is acceptable as a peer credential. The
   AddressType and the Address attributes are used only when IKE
   phase one negotiation starts automatically, i.e., the value of the
   AutoStart attribute in the ipSecIkeRuleTable is true. In which
   case, these two attributes together indicate the peer endpoint
   address.

3.4 Credential group

   This group specifies credentials to be used for IKE phase one
   negotiations.

   The ipSecCredentialSetTable specifies sets of credentials. The
   ipSecCredentialTable and ipSecCredentialFieldsTable together
   specify credentials. Each credential may contain multiple sub-
   fields. For example, a certificate may contain a unique serial
   number sub-field and an issuer name sub-field, etc. The
   ipSecCredentialFieldsTable defines the sub-fields and their values
   that MUST be matched against. The ipSecCredentialTable points to a
   set of criteria defined in the ipSecCredentialFieldsTable. The
   criteria MUST all be satisfied in order for a credential to be
   considered as acceptable. Certificates may also be revoked. The
   CrlDistributionPoint attribute in the ipSecCredentialTable
   indicates the Certificate Revocation List (CRL) distribution point
   where CRLs may be fetched.


3.5 Selector group

   This group specifies the selectors for IPsec rules.

   The ipSecSelectorSetTable specifies sets of selectors. Selectors
   within a set form an ordered list. The SelectorId attribute points
   to a valid instance in another table that describes a selector. To
   achieve scalability in policy distribution for large networks, it
   SHOULD point to the ipSecSelectorTable.



   Li, et al            Expires August, 2002                        6
                    IPsec Policy Information Base      February, 2002


   The ipSecAddressTable specifies individual or ranges of IP
   addresses and the ipSecL4PortTable specifies individual or ranges
   of layer 4 ports. The ipSecSelectorTable has references to these
   two tables.  Each row in the selector table can represent multiple
   selectors. These selectors are constructed as follows:

   1. Substitute the ipSecSelectorSrcAddressGroupId with all the IP
   addresses from the ipSecAddressTable whose ipSecAddressGroupId
   matches the ipSecSelectorSrcAddressGroupId.

   2. Substitute the ipSecSelectorDstAddressGroupId with all the IP
   addresses from the ipSecAddressTable whose ipSecAddressGroupId
   matches the ipSecSelectorDstAddressGroupId.

   3. Substitute the ipSecSelectorSrcPortGroupId with all the ports
   or ranges of port whose ipSecL4PortGroupId matches the
   ipSecSelectorSrcPortGroupId.

   4. Substitute the ipSecSelectorDstPortGroupId with all the ports
   or ranges of port whose ipSecL4PortGroupId matches the
   ipSecSelectorDstPortGroupId.

   5. Construct all the possible combinations of the above four
   fields. Then add to the combinations the ipSecSelectorProtocol,
   ipSecSelectorDscp and ipSecSelectorFlowLabel attributes to form
   the list of selectors.

   Selectors constructed from a single row have the same order within
   a selector set. The order is indicated by the Order attribute of
   the ipSecSelectorSetTable. The relative order among selectors
   constructed from a single row is unspecified. This is not an issue
   as long as these selectors are not over-lapping.

   The use of references in the ipSecSelectorTable instead of real IP
   addresses and port numbers reduces the number of bytes being
   pushed down to the PEP. Grouping of IP addresses and layer 4 ports
   serves the same purpose.

   The ipSecIpsoFilterSetTable specifies sets of IPSO filters.
   Filters within a set form an ordered list. The
   ipSecIpsoFilterTable contains IPSO filters.

3.6 Policy time period group

   This group specifies time periods during which a policy rule is
   valid. The ipSecRuleTimePeriodTable specifies a single time period
   within a day. The ipSecRuleTimePeriodSetTable specifies multiple
   time periods.

   Implementation of this group is optional.

3.7 Interface capability group


   Li, et al            Expires August, 2002                        7
                    IPsec Policy Information Base      February, 2002


   PEPs may have different capabilities. For example, some PEPs
   support nested Security Associations whereas others do not. This
   group allows a PEP to specify the capabilities associated with its
   different interface types.


   For ease of reference, a concise summary of the groups and tables
   is included in the next section.

4. Summary of the IPsec PIB

4.1 ipSecAssociation group
   This group specifies IPsec Security Associations.

4.1.1 ipSecRuleTable
   This table is the starting point for specifying an IPsec policy.
   It contains an ordered list of IPsec rules.

4.1.2 ipSecActionSetTable
   Specifies IPsec action sets.

4.1.3 ipSecStaticActionTable
   Specifies IPsec static actions.

4.1.4 ipSecNegotiationActionTable
   Specifies IPsec negotiation actions.

4.1.5 ipSecAssociationTable
   Specifies IPsec associations.

4.1.6 ipSecProposalSetTable
   Specifies IPsec proposal sets.

4.1.7 ipSecProposalTable
   Specifies IPsec proposals.

4.2 ipSecAhTransform group
   This group specifies AH Transforms.

4.2.1 ipSecAhTransformSetTable
   Specifies AH transform sets.

4.2.2 ipSecAhTransformTable
   Specifies AH transforms.

4.3 ipSecEspTransform group
   This group specifies ESP Transforms.

4.3.1 ipSecEspTransformSetTable
   Specifies ESP transform sets.

4.3.2 ipSecEspTransformTable
   Specifies ESP transforms.

   Li, et al            Expires August, 2002                        8
                    IPsec Policy Information Base      February, 2002



4.4 ipSecCompTransform group
   This group specifies Compression Transforms.

4.4.1 ipSecCompTransformSetTable
   Specifies IPComp transform sets.

4.4.2 ipSecCompTransformTable
   Specifies IP compression (IPCOMP) algorithms.

4.5 ipSecIkeAssociation group
   This group specifies IKE Security Associations.

4.5.1 ipSecIkeRuleTable
   Specifies IKE rules.

4.5.2 ipSecIkeActionSetTable
   Specifies IKE action sets.

4.5.3 ipSecIkeAssociationTable
   Specifies IKE associations.

4.5.4 ipSecIkeProposalSetTable
   Specifies IKE proposal sets.

4.5.5 ipSecIkeProposalTable
   Specifies IKE proposals.

4.5.6 ipSecIkePeerEndpointTable
   Specifies IKE peer endpoints.

4.6 ipSecCredential group
   This group specifies credentials for IKE phase one negotiations.

4.6.1 ipSecCredentialSetTable
   Specifies credential sets.

4.6.2 ipSecCredentialTable
   Specifies credentials.

4.6.3 ipSecCredentialFieldsTable
   Specifies sets of credential sub-fields and their values to be
   matched against.

4.7 ipSecSelector group
   This group specifies selectors for IPsec associations.

4.7.1 ipSecSelectorSetTable
   Specifies IPsec selector sets.

4.7.2 ipSecSelectorTable
   Specifies IPsec selectors.


   Li, et al            Expires August, 2002                        9
                    IPsec Policy Information Base      February, 2002


4.7.3 ipSecAddressTable
   Specifies IP addresses.

4.7.4 ipSecL4PortTable
   Specifies layer four port numbers.

4.7.5 ipSecIpsoFilterSetTable
   Specifies IPSO filter sets.

4.7.6 ipSecIpsoFilterTable
   Specifies IPSO filters.

4.8 ipSecPolicyTimePeriod group
   This group specifies the time periods during which a policy rule
   is valid.

4.8.1 ipSecRuleTimePeriodTable
   Specifies the time periods during which a policy rule is valid.

4.8.2 ipSecRuleTimePeriodSetTable
   Specifies time period sets.

4.9 ipSecIfCapability group
   This group specifies capabilities associated with interface types.

4.9.1 ipSecIfCapsTable
   Specifies capabilities that may be associated with an interface of
   a specific type.

4.10 ipSecPolicyPibConformance group
   This group specifies requirements for conformance to the IPsec
   Policy PIB.


5. The IPsec PIB Module

   IPSEC-POLICY-PIB PIB-DEFINITIONS ::= BEGIN

   IMPORTS
   Unsigned32, MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY,
   TEXTUAL-CONVENTION, MODULE-COMPLIANCE, OBJECT-GROUP
        FROM COPS-PR-SPPI
   TruthValue
        FROM SNMPv2-TC
   InstanceId, ReferenceId, TagId, TagReferenceId
        FROM COPS-PR-SPPI
   RoleCombination
        FROM FRAMEWORK-TC-PIB;

   ipSecPolicyPib MODULE-IDENTITY
   SUBJECT-CATEGORY { tbd } -- IPsec Client Type --
   LAST-UPDATED "200202241800Z"
   ORGANIZATION "IETF ipsp WG"

   Li, et al            Expires August, 2002                       10
                    IPsec Policy Information Base      February, 2002


   CONTACT-INFO "
                Man Li
                Nokia
                5 Wayside Road,
                Burlington, MA 01803
                Phone: +1 781 993 3923
                Email: man.m.li@nokia.com

                Avri Doria
                Div. of Computer Communications
                Lulea University of Technology
                SE-971 87
                Lulea, Sweden
                Phone: +46 920 49 3030
                Email: avri@sm.luth.se

                Jamie Jason
                Intel Corporation
                MS JF3-206
                2111 NE 25th Ave.
                Hillsboro, OR 97124
                Phone: +1 503 264 9531
                Fax: +1 503 264 9428
                Email: jamie.jason@intel.com

                Cliff Wang
                SmartPipes Inc.
                Suite 300, 565 Metro Place South
                Dublin, OH 43017
                Phone: +1 614 923 6241
                Email: CWang@smartpipes.com

                 Markus Stenberg
                 SSH Communications Security Corp.
                 Fredrikinkatu 42
                 FIN-00100 Helsinki, Finland
                 Phone: +358 20 500 7466
                 Email: markus.stenberg@ssh.com"


   DESCRIPTION
   "This PIB module contains a set of policy rule classes that
   describe IPsec policies."
   ::= { pib yyy } û- yyy to be assigned by IANA --


   Unsigned16 ::= TEXTUAL-CONVENTION
     STATUS       current
     DESCRIPTION
     "An unsigned 16 bit integer."
     SYNTAX    Unsigned32 (0..65535)

   ipSecAssociation OBJECT-IDENTITY

   Li, et al            Expires August, 2002                       11
                    IPsec Policy Information Base      February, 2002


     STATUS current
     DESCRIPTION
   "This group specifies IPsec Security Associations."
     ::= { ipSecPolicyPib 1 }

   ipSecAhTransform OBJECT-IDENTITY
     STATUS current
     DESCRIPTION
   "This group specifies AH Transforms."
     ::= { ipSecPolicyPib 2 }

   ipSecEspTransform OBJECT-IDENTITY
     STATUS current
     DESCRIPTION
   "This group specifies ESP Transforms."
     ::= { ipSecPolicyPib 3 }

   ipSecCompTransform OBJECT-IDENTITY
     STATUS current
     DESCRIPTION
   "This group specifies Comp Transforms."
     ::= { ipSecPolicyPib 4 }

   ipSecIkeAssociation OBJECT-IDENTITY
     STATUS current
     DESCRIPTION
   "This group specifies IKE Security Associations."
     ::= { ipSecPolicyPib 5 }

   ipSecCredential OBJECT-IDENTITY
     STATUS current
     DESCRIPTION
   "This group specifies credentials for IKE phase one negotiations."
     ::= { ipSecPolicyPib 6 }

   ipSecSelector OBJECT-IDENTITY
     STATUS current
     DESCRIPTION
   "This group specifies selectors for IPsec associations."
     ::= { ipSecPolicyPib 7 }

   ipSecPolicyTimePeriod OBJECT-IDENTITY
     STATUS current
     DESCRIPTION
   "This group specifies the time periods during which a policy rule
   is valid."
     ::= { ipSecPolicyPib 8 }

   ipSecIfCapability OBJECT-IDENTITY
     STATUS current
     DESCRIPTION
   "This group specifies capabilities associated with interface
   types."

   Li, et al            Expires August, 2002                       12
                    IPsec Policy Information Base      February, 2002


     ::= { ipSecPolicyPib 9 }

   ipSecPolicyPibConformance OBJECT-IDENTITY
     STATUS current
     DESCRIPTION
   "This group specifies requirements for conformance to the IPsec
   Policy PIB"
     ::= { ipSecPolicyPib 10 }


   --
   --
   -- The ipSecRuleTable
   --

   ipSecRuleTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecRuleEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "This table is the starting point for specifying an IPsec policy.
   It contains an ordered list of IPsec rules. "
     ::= { ipSecAssociation  1 }

   ipSecRuleEntry OBJECT-TYPE
     SYNTAX IpSecRuleEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecRulePrid }
     UNIQUENESS {
       ipSecRuleIfName,
       ipSecRuleRoles,
       ipSecRuleOrder
       }
     ::= { ipSecRuleTable 1 }

     IpSecRuleEntry ::= SEQUENCE {
        ipSecRulePrid InstanceId,
        ipSecRuleIfName SnmpAdminString,
        ipSecRuleRoles RoleCombination,
        ipSecRuleDirection INTEGER,
        ipSecRuleIpSecSelectorSetId TagReferenceId,
        ipSecRuleipSecIpsoFilterSetId TagReferenceId,
        ipSecRuleIpSecActionSetId TagReferenceId,
        ipSecRuleActionExecutionStrategy INTEGER,
        ipSecRuleOrder Unsigned16,
        ipSecRuleLimitNegotiation INTEGER,
        ipSecRuleAutoStart TruthValue,
        ipSecRuleIpSecRuleTimePeriodGroupId TagReferenceId
   }

   ipSecRulePrid OBJECT-TYPE

   Li, et al            Expires August, 2002                       13
                    IPsec Policy Information Base      February, 2002


     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecRuleEntry  1 }

   ipSecRuleIfName OBJECT-TYPE
     SYNTAX SnmpAdminString
     STATUS current
     DESCRIPTION
   "The interface capability set to which this IPsec rule applies.
   The interface capability name specified by this attribute MUST
   exist in the frwkIfCapSetTable [FR-PIB] prior to association with
   an instance of this class."
     ::= { ipSecRuleEntry  2 }

   ipSecRuleRoles OBJECT-TYPE
     SYNTAX RoleCombination
     STATUS current
     DESCRIPTION
   "Specifies the role combination of the interface to which this
   IPsec rule should apply. There must exist an instance in the
   frwkIfCapSetRoleComboTable [FR-PIB] specifying this role
   combination, together with the interface capability set specified
   by ipSecRuleIfName, prior to association with an instance of this
   class."
     ::= { ipSecRuleEntry  3 }

   ipSecRuleDirection OBJECT-TYPE
     SYNTAX INTEGER {
       in(1),
       out(2),
       bi-directional(3)
       }
     STATUS current
     DESCRIPTION
   "Specifies the direction of traffic to which this rule should
   apply."
     ::= { ipSecRuleEntry  4 }

   ipSecRuleIpSecSelectorSetId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecSelectorSetSelectorSetId }
     STATUS current
     DESCRIPTION
   "Identifies a set of selectors to be associated with this IPsec
   rule. "
     ::= { ipSecRuleEntry  5 }

   ipSecRuleipSecIpsoFilterSetId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecIpsoFilterSetFilterSetId }

   Li, et al            Expires August, 2002                       14
                    IPsec Policy Information Base      February, 2002


     STATUS current
     DESCRIPTION
   "Identifies a set of IPSO filters to be associated with this IPsec
   rule. A value of zero indicates that there are no IPSO filters
   associated with this rule.

   When the value of this attribute is not zero, the set of IPSO
   filters is ANDed with the set of Selectors specified by
   ipSecRuleIpSecSelectorSetId. In other words, a packet MUST match a
   selector in the selector sets and a filter in the IPSO filter sets
   before the actions associated with this rule can be applied."
     ::= { ipSecRuleEntry  6 }

   ipSecRuleIpSecActionSetId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecActionSetActionSetId }
     STATUS current
     DESCRIPTION
   "Identifies a set of IPsec actions to be associated with this
   rule."
     ::= { ipSecRuleEntry  7 }

   ipSecRuleActionExecutionStrategy OBJECT-TYPE
     SYNTAX INTEGER {
       doAll(1),
       doUntilSuccess(2)
       }
     STATUS current
     DESCRIPTION
   "Specifies the strategy to be used in executing the sequenced
   actions in the action set identified by ipSecRuleIpSecActionSetId.

   DoAll (1) causes the execution of all the actions in the action
   set according to their defined precedence order. The precedence
   order is specified by the ipSecActionSetOrder in the
   ipSecActionSetTable.

   DoUntilSuccess (2) causes the execution of actions according to
   their defined precedence order until a successful execution of a
   single action. The precedence order is specified by the
   ipSecActionSetOrder in the ipSecActionSetTable."
     ::= { ipSecRuleEntry  8 }

   ipSecRuleOrder OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "Specifies the precedence order of the rule within all the rules
   associated with {IfName, Roles}. A smaller value indicates a
   higher precedence order. "
     ::= { ipSecRuleEntry  9 }

   ipSecRuleLimitNegotiation OBJECT-TYPE

   Li, et al            Expires August, 2002                       15
                    IPsec Policy Information Base      February, 2002


     SYNTAX INTEGER {
       initiator(1),
       responder(2),
       both(3)
       }
     STATUS current
     DESCRIPTION
   "Limits the negotiation method. Before proceeding with a phase 2
   negotiation, the LimitNegotiation property of the IPsecRule is
   first checked to determine if the negotiation part indicated for
   the rule matches that of the current negotiation (Initiator,
   Responder, or Either).

   This attribute is ignored when an attempt is made to refresh an
   expiring SA (either side can initiate a refresh operation).  The
   system can determine that the negotiation is a refresh operation
   by checking to see if the selector information matches that of an
   existing SA. If LimitNegotiation does not match and the selector
   corresponds to a new SA, the negotiation is stopped. "
     ::= { ipSecRuleEntry  10 }

   ipSecRuleAutoStart OBJECT-TYPE
     SYNTAX TruthValue
     STATUS current
     DESCRIPTION
   "Indicates if this rule should be automatically executed."
     ::= { ipSecRuleEntry  11 }

   ipSecRuleIpSecRuleTimePeriodGroupId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecRuleTimePeriodSetRuleTimePeriodSetId }
     STATUS current
     DESCRIPTION
   "Identifies an IPsec rule time period set, specified in
   ipSecRuleTimePeriodSetTable, that is associated with this rule.

   A value of zero indicates that this IPsec rule is always valid."
     ::= { ipSecRuleEntry  12 }


   --
   --
   -- The ipSecActionSetTable
   --

   ipSecActionSetTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecActionSetEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IPsec action sets."
     ::= { ipSecAssociation  2 }


   Li, et al            Expires August, 2002                       16
                    IPsec Policy Information Base      February, 2002


   ipSecActionSetEntry OBJECT-TYPE
     SYNTAX IpSecActionSetEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecActionSetPrid }
     UNIQUENESS {
       ipSecActionSetActionSetId,
       ipSecActionSetActionId,
       ipSecActionSetDoActionLogging,
       ipSecActionSetDoPacketLogging,
       ipSecActionSetOrder
       }
     ::= { ipSecActionSetTable 1 }

     IpSecActionSetEntry ::= SEQUENCE {
        ipSecActionSetPrid InstanceId,
        ipSecActionSetActionSetId TagId,
        ipSecActionSetActionId Prid,
        ipSecActionSetDoActionLogging TruthValue,
        ipSecActionSetDoPacketLogging TruthValue,
        ipSecActionSetOrder Unsigned16
   }

   ipSecActionSetPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecActionSetEntry  1 }

   ipSecActionSetActionSetId OBJECT-TYPE
     SYNTAX TagId
     STATUS current
     DESCRIPTION
   "An IPsec action set is composed of one or more IPsec actions.
   Each action belonging to the same set has the same ActionSetId."
     ::= { ipSecActionSetEntry  2 }

   ipSecActionSetActionId OBJECT-TYPE
     SYNTAX Prid
     STATUS current
     DESCRIPTION
   "A pointer to a valid instance in another table that describes an
   action to be taken.

   For IPsec static actions, it MUST point to an instance in the
   ipSecStaticActionTable.

   For IPsec negotiation actions, it MUST point to an instance in the
   ipSecNegotiationActionTable. For other actions, it may point to an
   instance in a table specified by other PIB modules."

   Li, et al            Expires August, 2002                       17
                    IPsec Policy Information Base      February, 2002


     ::= { ipSecActionSetEntry  3 }

   ipSecActionSetDoActionLogging OBJECT-TYPE
     SYNTAX TruthValue
     STATUS current
     DESCRIPTION
   "Specifies whether a log message is to be generated when the
   action is performed.  This applies for ipSecNegotiationActions
   with the meaning of logging a message when the negotiation is
   attempted (with the success or failure result). This also applies
   for ipSecStaticAction only for PreconfiguredTransport action or
   PreconfiguredTunnel action with the meaning of logging a message
   when the preconfigured SA is actually installed in the SADB."
     ::= { ipSecActionSetEntry  4 }

   ipSecActionSetDoPacketLogging OBJECT-TYPE
     SYNTAX TruthValue
     STATUS current
     DESCRIPTION
   "Specifies whether to log when the resulting security association
   is used to process a packet. For ipSecStaticActions, a log message
   is to be generated when the IPsecBypass, IpsecDiscard or IKEReject
   actions are executed."
     ::= { ipSecActionSetEntry  5 }

   ipSecActionSetOrder OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "Specifies the precedence order of the action within the action
   set. An action with a smaller precedence order is to be applied
   before one with a larger precedence order. "
     ::= { ipSecActionSetEntry  6 }


   --
   --
   -- The ipSecStaticActionTable
   --

   ipSecStaticActionTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecStaticActionEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IPsec static actions."
     ::= { ipSecAssociation  3 }

   ipSecStaticActionEntry OBJECT-TYPE
     SYNTAX IpSecStaticActionEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"

   Li, et al            Expires August, 2002                       18
                    IPsec Policy Information Base      February, 2002


     PIB-INDEX { ipSecStaticActionPrid }
     UNIQUENESS {
       ipSecStaticActionAction,
       ipSecStaticActionTunnelEndpointId,
       ipSecStaticActionDfHandling,
       ipSecStaticActionSpi,
       ipSecStaticActionLifetimeSeconds,
       ipSecStaticActionLifetimeKilobytes,
       ipSecStaticActionSaTransformId
       }
     ::= { ipSecStaticActionTable 1 }

     IpSecStaticActionEntry ::= SEQUENCE {
        ipSecStaticActionPrid InstanceId,
        ipSecStaticActionAction INTEGER,
        ipSecStaticActionTunnelEndpointId ReferenceId,
        ipSecStaticActionDfHandling INTEGER,
        ipSecStaticActionSpi Unsigned32,
        ipSecStaticActionLifetimeSeconds Unsigned32,
        ipSecStaticActionLifetimeKilobytes Unsigned32,
        ipSecStaticActionSaTransformId Prid
   }

   ipSecStaticActionPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecStaticActionEntry  1 }

   ipSecStaticActionAction OBJECT-TYPE
     SYNTAX INTEGER {
       byPass(1),
       discard(2),
       ikeRejection(3),
       preConfiguredTransport(4),
       preConfiguredTunnel(5)
       }
     STATUS current
     DESCRIPTION
   "Specifies the IPsec action to be applied to the traffic. byPass
   (1) means that packets are to be allowed to pass in the clear.
   discard (2) means that packets are to be discarded. ikeRejection
   (3) means that that an IKE negotiation should not even be
   attempted or continued. preConfiguredTransport (4) means that an
   IPsec transport SA is pre-configured. preConfiguredTunnel (5)
   means that an IPsec tunnel SA is pre-configured. "
     ::= { ipSecStaticActionEntry  2 }

   ipSecStaticActionTunnelEndpointId OBJECT-TYPE
     SYNTAX ReferenceId
     PIB-REFERENCES    {ipSecAddressEntry }

   Li, et al            Expires August, 2002                       19
                    IPsec Policy Information Base      February, 2002


     STATUS current
     DESCRIPTION
   "When ipSecStaticActionAction is preConfiguredTunnel (5), this
   attribute indicates the peer gateway IP address. This address MUST
   be a single endpoint address.

   When ipSecStaticActionAction is not preConfiguredTunnel, this
   attribute MUST be zero."
     ::= { ipSecStaticActionEntry  3 }

   ipSecStaticActionDfHandling OBJECT-TYPE
     SYNTAX INTEGER {
       copy(1),
       set(2),
       clear(3)
       }
     STATUS current
     DESCRIPTION
   "When ipSecStaticActionAction is preConfiguredTunnel, this
   attribute specifies how the DF bit is managed.

   Copy (1) indicates to copy the DF bit from the internal IP header
   to the external IP header. Set (2) indicates to set the DF bit of
   the external IP header to 1. Clear (3) indicates to clear the DF
   bit of the external IP header to 0.

   When ipSecStaticActionAction is not preConfiguredTunnel, this
   attribute MUST be ignored. "
     ::= { ipSecStaticActionEntry  4 }

   ipSecStaticActionSpi OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies the SPI to be used with the SA Transform identified by
   ipSecStaticActionSaTransformId.

   When ipSecStaticActionAction is neither
   preConfiguredTransportAction nor preConfiguredTunnelAction, this
   attribute MUST be ignored."
     ::= { ipSecStaticActionEntry  5 }

   ipSecStaticActionLifetimeSeconds OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies the amount of time (in seconds) that a security
   association derived from this action should be used. When
   ipSecStaticActionAction is neither preConfiguredTransportAction
   nor preConfiguredTunnelAction, this attribute MUST be ignored.

   A value of zero indicates that there is not a lifetime associated
   with this action (i.e., infinite lifetime).

   Li, et al            Expires August, 2002                       20
                    IPsec Policy Information Base      February, 2002



   The actual lifetime of the preconfigured SA will be the smallest
   of the value of this LifetimeSeconds property and of the value of
   the MaxLifetimeSeconds property of the associated SA Transform.
   Except if the value of this LifetimeSeconds property is zero, then
   there will be no lifetime associated to this SA."
     ::= { ipSecStaticActionEntry  6 }

   ipSecStaticActionLifetimeKilobytes OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies the SA lifetime in kilobytes. When
   ipSecStaticActionAction is neither preConfiguredTransportAction
   nor preConfiguredTunnelAction, this attribute MUST be ignored.

   A value of zero indicates that there is not a lifetime associated
   with this action (i.e., infinite lifetime).

   The actual lifetime of the preconfigured SA will be the smallest
   of the value of this LifetimeKilobytes property and of the value
   of the MaxLifetimeKilobytes property of the associated SA
   transform. Except if the value of this LifetimeKilobytes property
   is zero, then there will be no lifetime associated with this
   action.
   "
     ::= { ipSecStaticActionEntry  7 }

   ipSecStaticActionSaTransformId OBJECT-TYPE
     SYNTAX Prid
     STATUS current
     DESCRIPTION
   "A pointer to a valid instance in another table that describes an
   SA transform, e.g, ipSecEspTransformTable, ipSecAhTransformTable."
     ::= { ipSecStaticActionEntry  8 }


   --
   --
   -- The ipSecNegotiationActionTable
   --

   ipSecNegotiationActionTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecNegotiationActionEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IPsec negotiation actions."
     ::= { ipSecAssociation  4 }

   ipSecNegotiationActionEntry OBJECT-TYPE
     SYNTAX IpSecNegotiationActionEntry
     STATUS current

   Li, et al            Expires August, 2002                       21
                    IPsec Policy Information Base      February, 2002


     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecNegotiationActionPrid }
     UNIQUENESS {
       ipSecNegotiationActionAction,
       ipSecNegotiationActionTunnelEndpointId,
       ipSecNegotiationActionDfHandling,
       ipSecNegotiationActionIpSecSecurityAssociationId,
       ipSecNegotiationActionKeyExchangeId
       }
     ::= { ipSecNegotiationActionTable 1 }

     IpSecNegotiationActionEntry ::= SEQUENCE {
        ipSecNegotiationActionPrid InstanceId,
        ipSecNegotiationActionAction INTEGER,
        ipSecNegotiationActionTunnelEndpointId ReferenceId,
        ipSecNegotiationActionDfHandling INTEGER,
        ipSecNegotiationActionIpSecSecurityAssociationId ReferenceId,
        ipSecNegotiationActionKeyExchangeId Prid
   }

   ipSecNegotiationActionPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecNegotiationActionEntry  1 }

   ipSecNegotiationActionAction OBJECT-TYPE
     SYNTAX INTEGER {
       transport(1),
       tunnel(2)
       }
     STATUS current
     DESCRIPTION
   "Specifies the IPsec action to be applied to the traffic.
   transport(1) means that the packet should be protected with a
   security association in transport mode. tunnel(2) means that the
   packet should be protected with a security association in tunnel
   mode.  If tunnel (2) is specified, ipSecActionTunnelEndpointId
   MUST also be specified."
     ::= { ipSecNegotiationActionEntry  2 }

   ipSecNegotiationActionTunnelEndpointId OBJECT-TYPE
     SYNTAX ReferenceId
     PIB-REFERENCES    {ipSecAddressEntry }
     STATUS current
     DESCRIPTION
   "When ipSecActionAction is tunnel (2), this attribute indicates
   the peer gateway IP address. This address MUST be a single
   endpoint address.


   Li, et al            Expires August, 2002                       22
                    IPsec Policy Information Base      February, 2002


   When ipSecActionAction is not tunnel, this attribute MUST be
   zero."
     ::= { ipSecNegotiationActionEntry  3 }

   ipSecNegotiationActionDfHandling OBJECT-TYPE
     SYNTAX INTEGER {
       copy(1),
       set(2),
       clear(3)
       }
     STATUS current
     DESCRIPTION
   "When ipSecActionAction is tunnel, this attribute specifies how
   the DF bit is managed.

   Copy (1) indicates to copy the DF bit from the internal IP header
   to the external IP header. Set (2) indicates to set the DF bit of
   the external IP header to 1. Clear (3) indicates to clear the DF
   bit of the external IP header to 0.

   When ipSecActionAction is not tunnel, this attribute MUST be
   ignored. "
     ::= { ipSecNegotiationActionEntry  4 }

   ipSecNegotiationActionIpSecSecurityAssociationId OBJECT-TYPE
     SYNTAX ReferenceId
     PIB-REFERENCES    {ipSecAssociationEntry }
     STATUS current
     DESCRIPTION
   "Pointer to a valid instance in the
   ipSecSecurityAssociationTable."
     ::= { ipSecNegotiationActionEntry  5 }

   ipSecNegotiationActionKeyExchangeId OBJECT-TYPE
     SYNTAX Prid
     STATUS current
     DESCRIPTION
   "A pointer to a valid instance in another table that describes key
   exchange associations. If a single IKE phase one negotiation is
   used for the key exchange, this attribute MUST point to an
   instance in the ipSecIkeAssociationTable. If multiple IKE phase
   one negotiations (e.g., with different modes) are to be tried
   until success, this attribute SHOULD point to ipSecIkeRuleTable.

   For other key exchange methods, this attribute may point to an
   instance of a PRC defined in some other PIB.

   A value of zero means that there is no key exchange procedure
   associated."
     ::= { ipSecNegotiationActionEntry  6 }


   --

   Li, et al            Expires August, 2002                       23
                    IPsec Policy Information Base      February, 2002


   --
   -- The ipSecAssociationTable
   --

   ipSecAssociationTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecAssociationEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IPsec associations."
     ::= { ipSecAssociation  5 }

   ipSecAssociationEntry OBJECT-TYPE
     SYNTAX IpSecAssociationEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecAssociationPrid }
     UNIQUENESS {
       ipSecAssociationMinLifetimeSeconds,
       ipSecAssociationMinLifetimeKilobytes,
       ipSecAssociationIdleDurationSeconds,
       ipSecAssociationUsePfs,
       ipSecAssociationVendorId,
       ipSecAssociationUseKeyExchangeGroup,
       ipSecAssociationDhGroup,
       ipSecAssociationGranularity,
       ipSecAssociationProposalSetId
       }
     ::= { ipSecAssociationTable 1 }

     IpSecAssociationEntry ::= SEQUENCE {
        ipSecAssociationPrid InstanceId,
        ipSecAssociationMinLifetimeSeconds Unsigned32,
        ipSecAssociationMinLifetimeKilobytes Unsigned32,
        ipSecAssociationIdleDurationSeconds Unsigned32,
        ipSecAssociationUsePfs TruthValue,
        ipSecAssociationVendorId OCTET STRING,
        ipSecAssociationUseKeyExchangeGroup TruthValue,
        ipSecAssociationDhGroup Unsigned16,
        ipSecAssociationGranularity INTEGER,
        ipSecAssociationProposalSetId TagReferenceId
   }

   ipSecAssociationPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecAssociationEntry  1 }

   ipSecAssociationMinLifetimeSeconds OBJECT-TYPE

   Li, et al            Expires August, 2002                       24
                    IPsec Policy Information Base      February, 2002


     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies the minimum SA seconds lifetime that will be accepted
   from a peer while negotiating an SA based upon this action.
   A value of zero indicates that there is no minimum lifetime
   enforced."
     ::= { ipSecAssociationEntry  2 }

   ipSecAssociationMinLifetimeKilobytes OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies the minimum kilobyte lifetime that will be accepted
   from a negotiating peer while negotiating an SA based upon this
   action.  A value of zero indicates that there is no minimum
   lifetime enforced."
     ::= { ipSecAssociationEntry  3 }

   ipSecAssociationIdleDurationSeconds OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies how long, in seconds, a security association may remain
   unused before it is deleted.

   A value of zero indicates that idle detection should not be used
   for the security association (only the seconds and kilobyte
   lifetimes will be used)."
     ::= { ipSecAssociationEntry  4 }

   ipSecAssociationUsePfs OBJECT-TYPE
     SYNTAX TruthValue
     STATUS current
     DESCRIPTION
   "Specifies whether or not to use PFS when refreshing keys."
     ::= { ipSecAssociationEntry  5 }

   ipSecAssociationVendorId OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "Specifies the IKE Vendor ID. This attribute is used together with
   the property ipSecAssociationDhGroup (when it is in the vendor-
   specific range) to identify the key exchange group.  This
   attribute is ignored unless ipSecAssociationUsePFS is true and
   ipSecAssociationUseKeyExchangeGroup is false and
   ipSecAssociationDhGroup is in the vendor-specific range (32768-
   65535)."
     ::= { ipSecAssociationEntry  6 }

   ipSecAssociationUseKeyExchangeGroup OBJECT-TYPE
     SYNTAX TruthValue

   Li, et al            Expires August, 2002                       25
                    IPsec Policy Information Base      February, 2002


     STATUS current
     DESCRIPTION
   "Specifies whether or not to use the same GroupId for phase 2 as
   was used in phase 1.  If UsePFS is false, then this attribute is
   ignored.

   A value of true indicates that the phase 2 GroupId should be the
   same as phase 1.  A value of false indicates that the group number
   specified by the ipSecSecurityAssociationDhGroup attribute SHALL
   be used for phase 2. "
     ::= { ipSecAssociationEntry  7 }

   ipSecAssociationDhGroup OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "Specifies the key exchange group to use for phase 2 when the
   property ipSecSecurityAssociationUsePfs is true and the property
   ipSecSecurityAssociationUseKeyExchangeGroup is false."
     ::= { ipSecAssociationEntry  8 }

   ipSecAssociationGranularity OBJECT-TYPE
     SYNTAX INTEGER {
       subnet(1),
       address(2),
       protocol(3),
       port(4)
       }
     STATUS current
     DESCRIPTION
   "Specifies how the proposed selector for the security association
   will be created.

   A value of 1 (subnet) indicates that the source and destination
   subnet masks of the filter entry are used.

   A value of 2 (address) indicates that only the source and
   destination IP addresses of the triggering packet are used.

   A value of 3 (protocol) indicates that the source and destination
   IP addresses and the IP protocol of the triggering packet are
   used.

   A value of 4 (port) indicates that the source and destination IP
   addresses and the IP protocol and the source and destination layer
   4 ports of the triggering packet are used. "
     ::= { ipSecAssociationEntry  9 }

   ipSecAssociationProposalSetId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecProposalSetProposalSetId }
     STATUS current
     DESCRIPTION

   Li, et al            Expires August, 2002                       26
                    IPsec Policy Information Base      February, 2002


   "Identifies a set of IPsec proposals that is associated with this
   IPsec association."
     ::= { ipSecAssociationEntry  10 }


   --
   --
   -- The ipSecProposalSetTable
   --

   ipSecProposalSetTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecProposalSetEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IPsec proposal sets. Proposals within a set are ORed
   with preference order. "
     ::= { ipSecAssociation  6 }

   ipSecProposalSetEntry OBJECT-TYPE
     SYNTAX IpSecProposalSetEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecProposalSetPrid }
     UNIQUENESS {
       ipSecProposalSetProposalSetId,
       ipSecProposalSetProposalId,
       ipSecProposalSetOrder
       }
     ::= { ipSecProposalSetTable 1 }

     IpSecProposalSetEntry ::= SEQUENCE {
        ipSecProposalSetPrid InstanceId,
        ipSecProposalSetProposalSetId TagId,
        ipSecProposalSetProposalId ReferenceId,
        ipSecProposalSetOrder Unsigned16
   }

   ipSecProposalSetPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecProposalSetEntry  1 }

   ipSecProposalSetProposalSetId OBJECT-TYPE
     SYNTAX TagId
     STATUS current
     DESCRIPTION



   Li, et al            Expires August, 2002                       27
                    IPsec Policy Information Base      February, 2002


   "An IPsec proposal set is composed of one or more IPsec proposals.
   Each proposal belonging to the same set has the same
   ProposalSetId."
     ::= { ipSecProposalSetEntry  2 }

   ipSecProposalSetProposalId OBJECT-TYPE
     SYNTAX ReferenceId
     PIB-REFERENCES    {ipSecProposalEntry }
     STATUS current
     DESCRIPTION
   "A pointer to a valid instance in the ipSecProposalTable."
     ::= { ipSecProposalSetEntry  3 }

   ipSecProposalSetOrder OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "An integer that specifies the precedence order of the proposal
   identified by ipSecProposalSetProposalId in a proposal set. The
   proposal set is identified by ipSecProposalSetProposalSetId.
   Proposals within a set are ORed with preference order. A smaller
   integer value indicates a higher preference."
     ::= { ipSecProposalSetEntry  4 }


   --
   --
   -- The ipSecProposalTable
   --

   ipSecProposalTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecProposalEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IPsec proposals. It has references to ESP, AH and
   IPCOMP Transform sets. Within a proposal, different types of
   transforms are ANDed. Multiple transforms of the same type are
   ORed with preference order."
     ::= { ipSecAssociation  7 }

   ipSecProposalEntry OBJECT-TYPE
     SYNTAX IpSecProposalEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecProposalPrid }
     UNIQUENESS {
       ipSecProposalEspTransformSetId,
       ipSecProposalAhTransformSetId,
       ipSecProposalCompTransformSetId
       }
     ::= { ipSecProposalTable 1 }

   Li, et al            Expires August, 2002                       28
                    IPsec Policy Information Base      February, 2002



     IpSecProposalEntry ::= SEQUENCE {
        ipSecProposalPrid InstanceId,
        ipSecProposalEspTransformSetId TagReferenceId,
        ipSecProposalAhTransformSetId TagReferenceId,
        ipSecProposalCompTransformSetId TagReferenceId
   }

   ipSecProposalPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecProposalEntry  1 }

   ipSecProposalEspTransformSetId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecEspTransformSetTransformSetId }
     STATUS current
     DESCRIPTION
   "An integer that identifies a set of ESP transforms, specified in
   ipSecEspTransformSetTable, that is associated with this proposal."
     ::= { ipSecProposalEntry  2 }

   ipSecProposalAhTransformSetId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecAhTransformSetTransformSetId }
     STATUS current
     DESCRIPTION
   "An integer that identifies an AH transform set, specified in
   ipSecAhTransformSetTable, that is associated with this proposal."
     ::= { ipSecProposalEntry  3 }

   ipSecProposalCompTransformSetId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecCompTransformSetTransformSetId }
     STATUS current
     DESCRIPTION
   "An integer that identifies a set of IPComp transforms, specified
   in ipSecCompTransformSetTable, that is associated with this
   proposal."
     ::= { ipSecProposalEntry  4 }


   --
   --
   -- The ipSecAhTransformSetTable
   --

   ipSecAhTransformSetTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecAhTransformSetEntry
     PIB-ACCESS install

   Li, et al            Expires August, 2002                       29
                    IPsec Policy Information Base      February, 2002


     STATUS current
     DESCRIPTION
   "Specifies AH transform sets. Within a transform set, the
   transforms are ORed with preference order. "
     ::= { ipSecAhTransform  1 }

   ipSecAhTransformSetEntry OBJECT-TYPE
     SYNTAX IpSecAhTransformSetEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecAhTransformSetPrid }
     UNIQUENESS {
       ipSecAhTransformSetTransformSetId,
       ipSecAhTransformSetTransformId,
       ipSecAhTransformSetOrder
       }
     ::= { ipSecAhTransformSetTable 1 }

     IpSecAhTransformSetEntry ::= SEQUENCE {
        ipSecAhTransformSetPrid InstanceId,
        ipSecAhTransformSetTransformSetId TagId,
        ipSecAhTransformSetTransformId ReferenceId,
        ipSecAhTransformSetOrder Unsigned16
   }

   ipSecAhTransformSetPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class. "
     ::= { ipSecAhTransformSetEntry  1 }

   ipSecAhTransformSetTransformSetId OBJECT-TYPE
     SYNTAX TagId
     STATUS current
     DESCRIPTION
   "An AH transform set is composed of one or more AH transforms.
   Each transform belonging to the same set has the same
   TransformSetId."
     ::= { ipSecAhTransformSetEntry  2 }

   ipSecAhTransformSetTransformId OBJECT-TYPE
     SYNTAX ReferenceId
     PIB-REFERENCES    {ipSecAhTransformEntry }
     STATUS current
     DESCRIPTION
   "A pointer to a valid instance in the ipSecAhTransformTable."
     ::= { ipSecAhTransformSetEntry  3 }

   ipSecAhTransformSetOrder OBJECT-TYPE
     SYNTAX Unsigned16

   Li, et al            Expires August, 2002                       30
                    IPsec Policy Information Base      February, 2002


     STATUS current
     DESCRIPTION
   "An integer that specifies the precedence order of the transform
   identified by ipSecAhTransformSetTransformId within a transform
   set. The transform set is identified by
   ipSecAhTransformSetTransformSetId. Transforms within a set are
   ORed with preference order. A smaller integer value indicates a
   higher preference."
     ::= { ipSecAhTransformSetEntry  4 }


   --
   --
   -- The ipSecAhTransformTable
   --

   ipSecAhTransformTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecAhTransformEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies AH transforms."
     ::= { ipSecAhTransform  2 }

   ipSecAhTransformEntry OBJECT-TYPE
     SYNTAX IpSecAhTransformEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecAhTransformPrid }
     UNIQUENESS {
       ipSecAhTransformTransformId,
       ipSecAhTransformIntegrityKey,
       ipSecAhTransformUseReplayPrevention,
       ipSecAhTransformReplayPreventionWindowSize,
       ipSecAhTransformVendorId,
       ipSecAhTransformMaxLifetimeSeconds,
       ipSecAhTransformMaxLifetimeKilobytes
       }
     ::= { ipSecAhTransformTable 1 }

     IpSecAhTransformEntry ::= SEQUENCE {
        ipSecAhTransformPrid InstanceId,
        ipSecAhTransformTransformId INTEGER,
        ipSecAhTransformIntegrityKey OCTET STRING,
        ipSecAhTransformUseReplayPrevention TruthValue,
        ipSecAhTransformReplayPreventionWindowSize Unsigned32,
        ipSecAhTransformVendorId OCTET STRING,
        ipSecAhTransformMaxLifetimeSeconds Unsigned32,
        ipSecAhTransformMaxLifetimeKilobytes Unsigned32
   }

   ipSecAhTransformPrid OBJECT-TYPE

   Li, et al            Expires August, 2002                       31
                    IPsec Policy Information Base      February, 2002


     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class. "
     ::= { ipSecAhTransformEntry  1 }

   ipSecAhTransformTransformId OBJECT-TYPE
     SYNTAX INTEGER {
       md5(2),
       sha-1(3),
       des(4)
       }
     STATUS current
     DESCRIPTION
   "Specifies the transform ID of the AH algorithm to propose."
     ::= { ipSecAhTransformEntry  2 }

   ipSecAhTransformIntegrityKey OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "When this AH transform instance is used for a Static Action, this
   attribute specifies the integrity key to be used. This attribute
   MUST be ignored when this AH transform instance is used for a
   Negotiation Action."
     ::= { ipSecAhTransformEntry  3 }

   ipSecAhTransformUseReplayPrevention OBJECT-TYPE
     SYNTAX TruthValue
     STATUS current
     DESCRIPTION
   "Specifies whether to enable replay prevention detection."
     ::= { ipSecAhTransformEntry  4 }

   ipSecAhTransformReplayPreventionWindowSize OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies, in bits, the length of the sliding window used by the
   replay prevention detection mechanism. The value of this property
   is ignored if UseReplayPrevention is false. It is assumed that the
   window size will be power of 2."
     ::= { ipSecAhTransformEntry  5 }

   ipSecAhTransformVendorId OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "Specifies the vendor ID for vendor-defined transforms."
     ::= { ipSecAhTransformEntry  6 }

   ipSecAhTransformMaxLifetimeSeconds OBJECT-TYPE

   Li, et al            Expires August, 2002                       32
                    IPsec Policy Information Base      February, 2002


     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies the maximum amount of time to propose for a security
   association to remain valid.

   A value of zero indicates that the default of 8 hours be used.  A
   non-zero value indicates the maximum seconds lifetime."
     ::= { ipSecAhTransformEntry  7 }

   ipSecAhTransformMaxLifetimeKilobytes OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies the maximum kilobyte lifetime to propose for a security
   association to remain valid.

   A value of zero indicates that there should be no maximum kilobyte
   lifetime.  A non-zero value specifies the desired kilobyte
   lifetime."
     ::= { ipSecAhTransformEntry  8 }


   --
   --
   -- The ipSecEspTransformSetTable
   --

   ipSecEspTransformSetTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecEspTransformSetEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies ESP transform sets. Within a transform set, the choices
   are ORed with preference order. "
     ::= { ipSecEspTransform  1 }

   ipSecEspTransformSetEntry OBJECT-TYPE
     SYNTAX IpSecEspTransformSetEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecEspTransformSetPrid }
     UNIQUENESS {
       ipSecEspTransformSetTransformSetId,
       ipSecEspTransformSetTransformId,
       ipSecEspTransformSetOrder
       }
     ::= { ipSecEspTransformSetTable 1 }

     IpSecEspTransformSetEntry ::= SEQUENCE {
        ipSecEspTransformSetPrid InstanceId,
        ipSecEspTransformSetTransformSetId TagId,

   Li, et al            Expires August, 2002                       33
                    IPsec Policy Information Base      February, 2002


        ipSecEspTransformSetTransformId ReferenceId,
        ipSecEspTransformSetOrder Unsigned16
   }

   ipSecEspTransformSetPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecEspTransformSetEntry  1 }

   ipSecEspTransformSetTransformSetId OBJECT-TYPE
     SYNTAX TagId
     STATUS current
     DESCRIPTION
   "An ESP transform set is composed of one or more ESP transforms.
   Each transform belonging to the same set has the same
   TransformSetId."
     ::= { ipSecEspTransformSetEntry  2 }

   ipSecEspTransformSetTransformId OBJECT-TYPE
     SYNTAX ReferenceId
     PIB-REFERENCES    {ipSecEspTransformEntry }
     STATUS current
     DESCRIPTION
   "A pointer to a valid instance in the ipSecEspTransformTable."
     ::= { ipSecEspTransformSetEntry  3 }

   ipSecEspTransformSetOrder OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "An integer that specifies the precedence order of the transform
   identified by ipSecEspTransformSetTransformId within a transform
   set. The transform set is identified by
   ipSecEspTransformSetTransformSetId. Transforms within a set are
   ORed with preference order. A smaller integer value indicates a
   higher preference."
     ::= { ipSecEspTransformSetEntry  4 }


   --
   --
   -- The ipSecEspTransformTable
   --

   ipSecEspTransformTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecEspTransformEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies ESP transforms."

   Li, et al            Expires August, 2002                       34
                    IPsec Policy Information Base      February, 2002


     ::= { ipSecEspTransform  2 }

   ipSecEspTransformEntry OBJECT-TYPE
     SYNTAX IpSecEspTransformEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecEspTransformPrid }
     UNIQUENESS {
       ipSecEspTransformIntegrityTransformId,
       ipSecEspTransformCipherTransformId,
       ipSecEspTransformIntegrityKey,
       ipSecEspTransformCipherKey,
       ipSecEspTransformCipherKeyRounds,
       ipSecEspTransformCipherKeyLength,
       ipSecEspTransformUseReplayPrevention,
       ipSecEspTransformReplayPreventionWindowSize,
       ipSecEspTransformVendorId,
       ipSecEspTransformMaxLifetimeSeconds,
       ipSecEspTransformMaxLifetimeKilobytes
       }
     ::= { ipSecEspTransformTable 1 }

     IpSecEspTransformEntry ::= SEQUENCE {
        ipSecEspTransformPrid InstanceId,
        ipSecEspTransformIntegrityTransformId INTEGER,
        ipSecEspTransformCipherTransformId INTEGER,
        ipSecEspTransformIntegrityKey OCTET STRING,
        ipSecEspTransformCipherKey OCTET STRING,
        ipSecEspTransformCipherKeyRounds Unsigned16,
        ipSecEspTransformCipherKeyLength Unsigned16,
        ipSecEspTransformUseReplayPrevention TruthValue,
        ipSecEspTransformReplayPreventionWindowSize Unsigned32,
        ipSecEspTransformVendorId OCTET STRING,
        ipSecEspTransformMaxLifetimeSeconds Unsigned32,
        ipSecEspTransformMaxLifetimeKilobytes Unsigned32
   }

   ipSecEspTransformPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecEspTransformEntry  1 }

   ipSecEspTransformIntegrityTransformId OBJECT-TYPE
     SYNTAX INTEGER {
       none(0),
       hmacMd5(1),
       hmacSha(2),
       desMac(3),
       kpdk(4)

   Li, et al            Expires August, 2002                       35
                    IPsec Policy Information Base      February, 2002


       }
     STATUS current
     DESCRIPTION
   "Specifies the transform ID of the ESP integrity algorithm to
   propose."
     ::= { ipSecEspTransformEntry  2 }

   ipSecEspTransformCipherTransformId OBJECT-TYPE
     SYNTAX INTEGER {
       desIV64(1),
       des(2),
       tripleDES(3),
       rc5(4),
       idea(5),
       cast(6),
       blowfish(7),
       tripleIDEA(8),
       desIV32(9),
       rc4(10),
       null(11)
       }
     STATUS current
     DESCRIPTION
   "Specifies the transform ID of the ESP encryption algorithm to
   propose."
     ::= { ipSecEspTransformEntry  3 }

   ipSecEspTransformIntegrityKey OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "When this ESP transform instance is used for a Static Action,
   this attribute specifies the integrity key to be used. This
   attribute MUST be ignored when this ESP transform instance is used
   for a Negotiation Action."
     ::= { ipSecEspTransformEntry  4 }

   ipSecEspTransformCipherKey OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "When this ESP transform instance is used for a Static Action,
   this attribute specifies the cipher key to be used. This attribute
   MUST be ignored when this ESP transform instance is used for a
   Negotiation Action."
     ::= { ipSecEspTransformEntry  5 }

   ipSecEspTransformCipherKeyRounds OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION



   Li, et al            Expires August, 2002                       36
                    IPsec Policy Information Base      February, 2002


   "Specifies the number of key rounds for the ESP encryption
   algorithm.  For encryption algorithms that use fixed number of key
   rounds, this value is ignored."
     ::= { ipSecEspTransformEntry  6 }

   ipSecEspTransformCipherKeyLength OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "Specifies, in bits, the key length for the ESP encryption
   algorithm. For encryption algorithms that use fixed-length keys,
   this value is ignored."
     ::= { ipSecEspTransformEntry  7 }

   ipSecEspTransformUseReplayPrevention OBJECT-TYPE
     SYNTAX TruthValue
     STATUS current
     DESCRIPTION
   "Specifies whether to enable replay prevention detection."
     ::= { ipSecEspTransformEntry  8 }

   ipSecEspTransformReplayPreventionWindowSize OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies, in bits, the length of the sliding window used by the
   replay prevention detection mechanism. The value of this property
   is ignored if UseReplayPrevention is false. It is assumed that the
   window size will be power of 2."
     ::= { ipSecEspTransformEntry  9 }

   ipSecEspTransformVendorId OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "Specifies the vendor ID for vendor-defined transforms."
     ::= { ipSecEspTransformEntry  10 }

   ipSecEspTransformMaxLifetimeSeconds OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies the maximum amount of time to propose for a security
   association to remain valid.

   A value of zero indicates that the default of 8 hours be used.  A
   non-zero value indicates the maximum seconds lifetime."
     ::= { ipSecEspTransformEntry  11 }

   ipSecEspTransformMaxLifetimeKilobytes OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION

   Li, et al            Expires August, 2002                       37
                    IPsec Policy Information Base      February, 2002


   "Specifies the maximum kilobyte lifetime to propose for a security
   association to remain valid.

   A value of zero indicates that there should be no maximum kilobyte
   lifetime.  A non-zero value specifies the desired kilobyte
   lifetime."
     ::= { ipSecEspTransformEntry  12 }


   --
   --
   -- The ipSecCompTransformSetTable
   --

   ipSecCompTransformSetTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecCompTransformSetEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IPComp transform sets. Within a transform set, the
   choices are ORed with preference order."
     ::= { ipSecCompTransform  1 }

   ipSecCompTransformSetEntry OBJECT-TYPE
     SYNTAX IpSecCompTransformSetEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecCompTransformSetPrid }
     UNIQUENESS {
       ipSecCompTransformSetTransformSetId,
       ipSecCompTransformSetTransformId,
       ipSecCompTransformSetOrder
       }
     ::= { ipSecCompTransformSetTable 1 }

     IpSecCompTransformSetEntry ::= SEQUENCE {
        ipSecCompTransformSetPrid InstanceId,
        ipSecCompTransformSetTransformSetId TagId,
        ipSecCompTransformSetTransformId ReferenceId,
        ipSecCompTransformSetOrder Unsigned16
   }

   ipSecCompTransformSetPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecCompTransformSetEntry  1 }

   ipSecCompTransformSetTransformSetId OBJECT-TYPE
     SYNTAX TagId

   Li, et al            Expires August, 2002                       38
                    IPsec Policy Information Base      February, 2002


     STATUS current
     DESCRIPTION
   "An IPCOMP transform set is composed of one or more IPCOMP
   transforms. Each transform belonging to the same set has the same
   TransformSetId."
     ::= { ipSecCompTransformSetEntry  2 }

   ipSecCompTransformSetTransformId OBJECT-TYPE
     SYNTAX ReferenceId
     PIB-REFERENCES    {ipSecCompTransformEntry }
     STATUS current
     DESCRIPTION
   "A pointer to a valid instance in the ipSecCompTransformTable."
     ::= { ipSecCompTransformSetEntry  3 }

   ipSecCompTransformSetOrder OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "An integer that specifies the precedence order of the transform
   identified by ipSecCompTransformSetTransformId within a transform
   set. The transform set is identified by
   ipSecCompTransformSetTransformSetId. Transforms within a set are
   ORed with preference order. A smaller integer value indicates a
   higher preference."
     ::= { ipSecCompTransformSetEntry  4 }


   --
   --
   -- The ipSecCompTransformTable
   --

   ipSecCompTransformTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecCompTransformEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IP compression (IPCOMP) algorithms."
     ::= { ipSecCompTransform  2 }

   ipSecCompTransformEntry OBJECT-TYPE
     SYNTAX IpSecCompTransformEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecCompTransformPrid }
     UNIQUENESS {
       ipSecCompTransformAlgorithm,
       ipSecCompTransformDictionarySize,
       ipSecCompTransformPrivateAlgorithm,
       ipSecCompTransformVendorId,
       ipSecCompTransformMaxLifetimeSeconds,

   Li, et al            Expires August, 2002                       39
                    IPsec Policy Information Base      February, 2002


       ipSecCompTransformMaxLifetimeKilobytes
       }
     ::= { ipSecCompTransformTable 1 }

     IpSecCompTransformEntry ::= SEQUENCE {
        ipSecCompTransformPrid InstanceId,
        ipSecCompTransformAlgorithm INTEGER,
        ipSecCompTransformDictionarySize Unsigned16,
        ipSecCompTransformPrivateAlgorithm Unsigned32,
        ipSecCompTransformVendorId OCTET STRING,
        ipSecCompTransformMaxLifetimeSeconds Unsigned32,
        ipSecCompTransformMaxLifetimeKilobytes Unsigned32
   }

   ipSecCompTransformPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecCompTransformEntry  1 }

   ipSecCompTransformAlgorithm OBJECT-TYPE
     SYNTAX INTEGER {
       oui(1),
       deflate(2),
       lzs(3)
       }
     STATUS current
     DESCRIPTION
   "Specifies the transform ID of the IPCOMP compression algorithm to
   propose."
     ::= { ipSecCompTransformEntry  2 }

   ipSecCompTransformDictionarySize OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "Specifies the log2 maximum size of the dictionary for the
   compression algorithm.  For compression algorithms that have pre-
   defined dictionary sizes, this value is ignored."
     ::= { ipSecCompTransformEntry  3 }

   ipSecCompTransformPrivateAlgorithm OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies a private vendor-specific compression algorithm."
     ::= { ipSecCompTransformEntry  4 }

   ipSecCompTransformVendorId OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current

   Li, et al            Expires August, 2002                       40
                    IPsec Policy Information Base      February, 2002


     DESCRIPTION
   "Specifies the vendor ID for vendor-defined transforms."
     ::= { ipSecCompTransformEntry  5 }

   ipSecCompTransformMaxLifetimeSeconds OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies the maximum amount of time to propose for a security
   association to remain valid.

   A value of zero indicates that the default of 8 hours be used.  A
   non-zero value indicates the maximum seconds lifetime."
     ::= { ipSecCompTransformEntry  6 }

   ipSecCompTransformMaxLifetimeKilobytes OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies the maximum kilobyte lifetime to propose for a security
   association to remain valid.

   A value of zero indicates that there should be no maximum kilobyte
   lifetime.  A non-zero value specifies the desired kilobyte
   lifetime."
     ::= { ipSecCompTransformEntry  7 }


   --
   --
   -- The ipSecIkeRuleTable
   --

   ipSecIkeRuleTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecIkeRuleEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IKE rules. This table is required only when specifying:

   - Multiple IKE phase one actions (e.g., with different exchange
   modes) that are associated with one IPsec association. These
   actions are to be tried in sequence till one success.

   - IKE phase one actions that start automatically.

   Support of this table is optional."
     ::= { ipSecIkeAssociation  1 }

   ipSecIkeRuleEntry OBJECT-TYPE
     SYNTAX IpSecIkeRuleEntry
     STATUS current
     DESCRIPTION

   Li, et al            Expires August, 2002                       41
                    IPsec Policy Information Base      February, 2002


   "Specifies an instance of this class"
     PIB-INDEX { ipSecIkeRulePrid }
     UNIQUENESS {
       ipSecIkeRuleIfName,
       ipSecIkeRuleRoles,
       ipSecIkeRuleIkeActionSetId,
       ipSecIkeRuleActionExecutionStrategy,
       ipSecIkeRuleLimitNegotiation,
       ipSecIkeRuleAutoStart
       }
     ::= { ipSecIkeRuleTable 1 }

     IpSecIkeRuleEntry ::= SEQUENCE {
        ipSecIkeRulePrid InstanceId,
        ipSecIkeRuleIfName SnmpAdminString,
        ipSecIkeRuleRoles RoleCombination,
        ipSecIkeRuleIkeActionSetId TagReferenceId,
        ipSecIkeRuleActionExecutionStrategy INTEGER,
        ipSecIkeRuleLimitNegotiation INTEGER,
        ipSecIkeRuleAutoStart TruthValue,
        ipSecIkeRuleIpSecRuleTimePeriodGroupId TagReferenceId
   }

   ipSecIkeRulePrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecIkeRuleEntry  1 }

   ipSecIkeRuleIfName OBJECT-TYPE
     SYNTAX SnmpAdminString
     STATUS current
     DESCRIPTION
   "The interface capability set to which this IKE rule applies. The
   interface capability name specified by this attribute must exist
   in the frwkIfCapSetTable [FR-PIB] prior to association with an
   instance of this class.

   This attribute MUST be ignored if ipSecIkeRuleAutoStart is false."
     ::= { ipSecIkeRuleEntry  2 }

   ipSecIkeRuleRoles OBJECT-TYPE
     SYNTAX RoleCombination
     STATUS current
     DESCRIPTION
   "Specifies the role combination of the interface to which this IKE
   rule should apply. There must exist an instance in the
   frwkIfCapSetRoleComboTable [FR-PIB] specifying this role
   combination, together with the interface capability set specified
   by ipSecIkeRuleIfName, prior to association with an instance of
   this class.

   Li, et al            Expires August, 2002                       42
                    IPsec Policy Information Base      February, 2002



   This attribute MUST be ignored if ipSecIkeRuleAutoStart is false."
     ::= { ipSecIkeRuleEntry  3 }

   ipSecIkeRuleIkeActionSetId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecIkeActionSetActionSetId }
     STATUS current
     DESCRIPTION
   "Identifies a set of IKE actions to be associated with this rule."
     ::= { ipSecIkeRuleEntry  4 }

   ipSecIkeRuleActionExecutionStrategy OBJECT-TYPE
     SYNTAX INTEGER {
       doAll(1),
       doUntilSuccess(2)
       }
     STATUS current
     DESCRIPTION
   "Specifies the strategy to be used in executing the sequenced
   actions in the action set identified by ipSecRuleIpSecActionSetId.

   DoAll (1) causes the execution of all the actions in the action
   set according to their defined precedence order. The precedence
   order is specified by the ipSecActionSetOrder in
   ipSecIkeActionSetTable.

   DoUntilSuccess (2) causes the execution of actions according to
   their defined precedence order until a successful execution of a
   single action. The precedence order is specified by the
   ipSecActionSetOrder in ipSecIkeActionSetTable."
     ::= { ipSecIkeRuleEntry  5 }

   ipSecIkeRuleLimitNegotiation OBJECT-TYPE
     SYNTAX INTEGER {
       initiator(1),
       responder(2),
       both(3)
       }
     STATUS current
     DESCRIPTION
   "Limits the negotiation method. Before proceeding with a phase 1
   negotiation, this property is checked to determine if the
   negotiation role of the rule matches that defined for the
   negotiation being undertaken (e.g., Initiator, Responder, or
   Both). If this check fails (e.g. the current role is IKE responder
   while the rule specifies IKE initiator), then the IKE negotiation
   is stopped. Note that this only applies to new IKE phase 1
   negotiations and has no effect on either renegotiation or refresh
   operations with peers for which an established SA already exists."
     ::= { ipSecIkeRuleEntry  6 }

   ipSecIkeRuleAutoStart OBJECT-TYPE

   Li, et al            Expires August, 2002                       43
                    IPsec Policy Information Base      February, 2002


     SYNTAX TruthValue
     STATUS current
     DESCRIPTION
   "Indicates if this rule should be automatically executed."
     ::= { ipSecIkeRuleEntry  7 }

   ipSecIkeRuleIpSecRuleTimePeriodGroupId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecRuleTimePeriodSetRuleTimePeriodSetId }
     STATUS current
     DESCRIPTION
   "Identifies a rule time period set, specified in
   ipSecRuleTimePeriodSetTable, that is associated with this rule.

   A value of zero indicates that this rule is always valid."
     ::= { ipSecIkeRuleEntry  8 }


   --
   --
   -- The ipSecIkeActionSetTable
   --

   ipSecIkeActionSetTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecIkeActionSetEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IKE action sets."
     ::= { ipSecIkeAssociation  2 }

   ipSecIkeActionSetEntry OBJECT-TYPE
     SYNTAX IpSecIkeActionSetEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecIkeActionSetPrid }
     UNIQUENESS {
       ipSecIkeActionSetActionSetId,
       ipSecIkeActionSetActionId,
       ipSecIkeActionSetOrder
       }
     ::= { ipSecIkeActionSetTable 1 }

     IpSecIkeActionSetEntry ::= SEQUENCE {
        ipSecIkeActionSetPrid InstanceId,
        ipSecIkeActionSetActionSetId TagId,
        ipSecIkeActionSetActionId Prid,
        ipSecIkeActionSetOrder Unsigned16
   }

   ipSecIkeActionSetPrid OBJECT-TYPE
     SYNTAX InstanceId

   Li, et al            Expires August, 2002                       44
                    IPsec Policy Information Base      February, 2002


     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecIkeActionSetEntry  1 }

   ipSecIkeActionSetActionSetId OBJECT-TYPE
     SYNTAX TagId
     STATUS current
     DESCRIPTION
   "An IKE action set is composed of one or more IKE actions. Each
   action belonging to the same set has the same ActionSetId."
     ::= { ipSecIkeActionSetEntry  2 }

   ipSecIkeActionSetActionId OBJECT-TYPE
     SYNTAX Prid
     STATUS current
     DESCRIPTION
   "A pointer to a valid instance in the ipSecIkeAssociationTable."
     ::= { ipSecIkeActionSetEntry  3 }

   ipSecIkeActionSetOrder OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "Specifies the precedence order of the action within the action
   set. An action with a smaller precedence order is to be tried
   before one with a larger precedence order. "
     ::= { ipSecIkeActionSetEntry  4 }


   --
   --
   -- The ipSecIkeAssociationTable
   --

   ipSecIkeAssociationTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecIkeAssociationEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IKE associations."
     ::= { ipSecIkeAssociation  3 }

   ipSecIkeAssociationEntry OBJECT-TYPE
     SYNTAX IpSecIkeAssociationEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecIkeAssociationPrid }
     UNIQUENESS {
       ipSecIkeAssociationMinLiftetimeSeconds,
       ipSecIkeAssociationMinLifetimeKilobytes,

   Li, et al            Expires August, 2002                       45
                    IPsec Policy Information Base      February, 2002


       ipSecIkeAssociationIdleDurationSeconds,
       ipSecIkeAssociationExchangeMode,
       ipSecIkeAssociationUseIkeIdentityType,
       ipSecIkeAssociationUseIkeIdentityValue,
       ipSecIkeAssociationIkePeerEndpoint,
       ipSecIkeAssociationPresharedKey,
       ipSecIkeAssociationVendorId,
       ipSecIkeAssociationAggressiveModeGroupId,
       ipSecIkeAssociationLocalCredentialId,
       ipSecIkeAssociationDoActionLogging,
       ipSecIkeAssociationIkeProposalSetId
       }
     ::= { ipSecIkeAssociationTable 1 }

     IpSecIkeAssociationEntry ::= SEQUENCE {
        ipSecIkeAssociationPrid InstanceId,
        ipSecIkeAssociationMinLiftetimeSeconds Unsigned32,
        ipSecIkeAssociationMinLifetimeKilobytes Unsigned32,
        ipSecIkeAssociationIdleDurationSeconds Unsigned32,
        ipSecIkeAssociationExchangeMode INTEGER,
        ipSecIkeAssociationUseIkeIdentityType INTEGER,
        ipSecIkeAssociationUseIkeIdentityValue OCTET STRING,
        ipSecIkeAssociationIkePeerEndpoint ReferenceId,
        ipSecIkeAssociationPresharedKey OCTET STRING,
        ipSecIkeAssociationVendorId OCTET STRING,
        ipSecIkeAssociationAggressiveModeGroupId Unsigned16,
        ipSecIkeAssociationLocalCredentialId TagReferenceId,
        ipSecIkeAssociationDoActionLogging TruthValue,
        ipSecIkeAssociationIkeProposalSetId TagReferenceId
   }

   ipSecIkeAssociationPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecIkeAssociationEntry  1 }

   ipSecIkeAssociationMinLiftetimeSeconds OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies the minimum SA seconds lifetime that will be accepted
   from a peer while negotiating an SA based upon this action.

   A value of zero indicates that there is no minimum lifetime
   enforced."
     ::= { ipSecIkeAssociationEntry  2 }

   ipSecIkeAssociationMinLifetimeKilobytes OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current

   Li, et al            Expires August, 2002                       46
                    IPsec Policy Information Base      February, 2002


     DESCRIPTION
   "Specifies the minimum kilobyte lifetime that will be accepted
   from a negotiating peer while negotiating an SA based upon this
   action.

   A value of zero indicates that there is no minimum lifetime
   enforced."
     ::= { ipSecIkeAssociationEntry  3 }

   ipSecIkeAssociationIdleDurationSeconds OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies how long, in seconds, a security association may remain
   unused before it is deleted.

   A value of zero indicates that idle detection should not be used
   for the security association (only the seconds and kilobyte
   lifetimes will be used)."
     ::= { ipSecIkeAssociationEntry  4 }

   ipSecIkeAssociationExchangeMode OBJECT-TYPE
     SYNTAX INTEGER {
       baseMode(1),
       mainMode(2),
       aggressiveMode(4)
       }
     STATUS current
     DESCRIPTION
   "Specifies the negotiation mode that the IKE server will use for
   phase one."
     ::= { ipSecIkeAssociationEntry  5 }

   ipSecIkeAssociationUseIkeIdentityType OBJECT-TYPE
     SYNTAX INTEGER {
       ipV4-Address(1),
       fqdn(2),
       user-Fqdn(3),
       ipV4-Subnet(4),
       ipV6-Address(5),
       ipV6-Subnet(6),
       ipV4-Address-Range(7),
       ipV6-Address-Range(8),
       der-Asn1-DN(9),
       der-Asn1-GN(10),
       key-Id(11)
       }
     STATUS current
     DESCRIPTION
   "Specifies the type of IKE identity to use during IKE phase one
   negotiation."
     ::= { ipSecIkeAssociationEntry  6 }


   Li, et al            Expires August, 2002                       47
                    IPsec Policy Information Base      February, 2002


   ipSecIkeAssociationUseIkeIdentityValue OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "Specifies the ID payload value to be provided to the peer during
   IKE phase one negotiation."
     ::= { ipSecIkeAssociationEntry  7 }

   ipSecIkeAssociationIkePeerEndpoint OBJECT-TYPE
     SYNTAX ReferenceId
     PIB-REFERENCES    {ipSecIkePeerEndpointEntry }
     STATUS current
     DESCRIPTION
   "Pointer to a valid instance in the ipSecIkePeerEndpointTable to
   indicate an IKE peer endpoint."
     ::= { ipSecIkeAssociationEntry  8 }

   ipSecIkeAssociationPresharedKey OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "This attribute specifies the preshared key or secret to use for
   IKE authentication. This is the key for all the IKE proposals of
   this association that set ipSecIkeProposalAuthenticationMethod to
   presharedKey(1)."
     ::= { ipSecIkeAssociationEntry  9 }

   ipSecIkeAssociationVendorId OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "Specifies the value to be used in the Vendor ID payload.

   A value of NULL means that Vendor ID payload will be neither
   generated nor accepted. A non-NULL value means that a Vendor ID
   payload will be generated (when acting as an initiator) or is
   expected (when acting as a responder). "
     ::= { ipSecIkeAssociationEntry  10 }

   ipSecIkeAssociationAggressiveModeGroupId OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "Specifies the group ID to be used for aggressive mode. This
   attribute is ignored unless the attribute
   ipSecIkeAssociationExchangeMode is set to 4 (aggressive mode). If
   the value of this attribute is from the vendor-specific range
   (32768-65535), this attribute qualifies the group number."
     ::= { ipSecIkeAssociationEntry  11 }

   ipSecIkeAssociationLocalCredentialId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecCredentialSetSetId }

   Li, et al            Expires August, 2002                       48
                    IPsec Policy Information Base      February, 2002


     STATUS current
     DESCRIPTION
   "Indicates a group of credentials. One of the credentials in the
   group MUST be used when establishing an IKE association with the
   peer endpoint."
     ::= { ipSecIkeAssociationEntry  12 }

   ipSecIkeAssociationDoActionLogging OBJECT-TYPE
     SYNTAX TruthValue
     STATUS current
     DESCRIPTION
   "Specifies whether a log message is to be generated when the
   negotiation is attempted (with the success or failure result)."
     ::= { ipSecIkeAssociationEntry  13 }

   ipSecIkeAssociationIkeProposalSetId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecIkeProposalSetProposalSetId }
     STATUS current
     DESCRIPTION
   "Identifies a set of IKE proposals that is associated with this
   IKE association."
     ::= { ipSecIkeAssociationEntry  14 }


   --
   --
   -- The ipSecIkeProposalSetTable
   --

   ipSecIkeProposalSetTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecIkeProposalSetEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IKE proposal sets. Proposals within a set are ORed with
   preference order. "
     ::= { ipSecIkeAssociation  4 }

   ipSecIkeProposalSetEntry OBJECT-TYPE
     SYNTAX IpSecIkeProposalSetEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecIkeProposalSetPrid }
     UNIQUENESS {
       ipSecIkeProposalSetProposalSetId,
       ipSecIkeProposalSetProposalId,
       ipSecIkeProposalSetOrder
       }
     ::= { ipSecIkeProposalSetTable 1 }

     IpSecIkeProposalSetEntry ::= SEQUENCE {

   Li, et al            Expires August, 2002                       49
                    IPsec Policy Information Base      February, 2002


        ipSecIkeProposalSetPrid InstanceId,
        ipSecIkeProposalSetProposalSetId TagId,
        ipSecIkeProposalSetProposalId ReferenceId,
        ipSecIkeProposalSetOrder Unsigned16
   }

   ipSecIkeProposalSetPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecIkeProposalSetEntry  1 }

   ipSecIkeProposalSetProposalSetId OBJECT-TYPE
     SYNTAX TagId
     STATUS current
     DESCRIPTION
   "An IKE proposal set is composed of one or more IKE proposals.
   Each proposal belonging to the same set has the same
   ProposalSetId. "
     ::= { ipSecIkeProposalSetEntry  2 }

   ipSecIkeProposalSetProposalId OBJECT-TYPE
     SYNTAX ReferenceId
     PIB-REFERENCES    {ipSecIkeProposalEntry }
     STATUS current
     DESCRIPTION
   "A pointer to a valid instance in the ipSecIkeProposalTable."
     ::= { ipSecIkeProposalSetEntry  3 }

   ipSecIkeProposalSetOrder OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "An integer that specifies the precedence order of the proposal
   identified by ipSecIkeProposalSetProposalId in a proposal set. The
   proposal set is identified by ipSecIkeProposalSetProposalSetId.
   Proposals within a set are ORed with preference order. A smaller
   integer value indicates a higher preference."
     ::= { ipSecIkeProposalSetEntry  4 }


   --
   --
   -- The ipSecIkeProposalTable
   --

   ipSecIkeProposalTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecIkeProposalEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION

   Li, et al            Expires August, 2002                       50
                    IPsec Policy Information Base      February, 2002


   "Specifies IKE proposals."
     ::= { ipSecIkeAssociation  5 }

   ipSecIkeProposalEntry OBJECT-TYPE
     SYNTAX IpSecIkeProposalEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecIkeProposalPrid }
     UNIQUENESS {
       ipSecIkeProposalMaxLifetimeSeconds,
       ipSecIkeProposalMaxLifetimeKilobytes,
       ipSecIkeProposalCipherAlgorithm,
       ipSecIkeProposalHashAlgorithm,
       ipSecIkeProposalAuthenticationMethod,
       ipSecIkeProposalPrfAlgorithm,
       ipSecIkeProposalIkeDhGroup,
       ipSecIkeProposalVendorId
       }
     ::= { ipSecIkeProposalTable 1 }

     IpSecIkeProposalEntry ::= SEQUENCE {
        ipSecIkeProposalPrid InstanceId,
        ipSecIkeProposalMaxLifetimeSeconds Unsigned32,
        ipSecIkeProposalMaxLifetimeKilobytes Unsigned32,
        ipSecIkeProposalCipherAlgorithm INTEGER,
        ipSecIkeProposalHashAlgorithm INTEGER,
        ipSecIkeProposalAuthenticationMethod INTEGER,
        ipSecIkeProposalPrfAlgorithm Unsigned16,
        ipSecIkeProposalIkeDhGroup Unsigned16,
        ipSecIkeProposalVendorId OCTET STRING
   }

   ipSecIkeProposalPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecIkeProposalEntry  1 }

   ipSecIkeProposalMaxLifetimeSeconds OBJECT-TYPE
     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies the maximum amount of time to propose for a security
   association to remain valid.

   A value of zero indicates that the default of 8 hours be used.  A
   non-zero value indicates the maximum seconds lifetime."
     ::= { ipSecIkeProposalEntry  2 }

   ipSecIkeProposalMaxLifetimeKilobytes OBJECT-TYPE

   Li, et al            Expires August, 2002                       51
                    IPsec Policy Information Base      February, 2002


     SYNTAX Unsigned32
     STATUS current
     DESCRIPTION
   "Specifies the maximum kilobyte lifetime to propose for a security
   association to remain valid.

   A value of zero indicates that there should be no maximum kilobyte
   lifetime.  A non-zero value specifies the desired kilobyte
   lifetime."
     ::= { ipSecIkeProposalEntry  3 }

   ipSecIkeProposalCipherAlgorithm OBJECT-TYPE
     SYNTAX INTEGER {
       des-CBC(1),
       idea-CBC(2),
       blowfish-CBC(3),
       rc5-R16-B64-CBC(4),
       tripleDes-CBC(5),
       cast-CBC(6)
       }
     STATUS current
     DESCRIPTION
   "Specifies the encryption algorithm to propose for the IKE
   association."
     ::= { ipSecIkeProposalEntry  4 }

   ipSecIkeProposalHashAlgorithm OBJECT-TYPE
     SYNTAX INTEGER {
       md5(1),
       sha-1(2),
       tiger(3)
       }
     STATUS current
     DESCRIPTION
   "Specifies the hash algorithm to propose for the IKE association."
     ::= { ipSecIkeProposalEntry  5 }

   ipSecIkeProposalAuthenticationMethod OBJECT-TYPE
     SYNTAX INTEGER {
       presharedKey(1),
       dssSignatures(2),
       rsaSignatures(3),
       rsaEncryption(4),
       revisedRsaEncryption(5),
       kerberos(6)
       }
     STATUS current
     DESCRIPTION
   "Specifies the authentication method to propose for the IKE
   association."
     ::= { ipSecIkeProposalEntry  6 }

   ipSecIkeProposalPrfAlgorithm OBJECT-TYPE

   Li, et al            Expires August, 2002                       52
                    IPsec Policy Information Base      February, 2002


     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "Specifies the Psuedo-Random Function (PRF) to propose for the IKE
   association."
     ::= { ipSecIkeProposalEntry  7 }

   ipSecIkeProposalIkeDhGroup OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "Specifies the Diffie-Hellman group to propose for the IKE
   association. The value of this property is to be ignored when
   doing aggressive mode."
     ::= { ipSecIkeProposalEntry  8 }

   ipSecIkeProposalVendorId OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "Further qualifies the key exchange group.  The property is
   ignored unless the exchange is not in aggressive mode and the
   property GroupID is in the vendor-specific range."
     ::= { ipSecIkeProposalEntry  9 }


   --
   --
   -- The ipSecIkePeerEndpointTable
   --

   ipSecIkePeerEndpointTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecIkePeerEndpointEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IKE peer endpoints."
     ::= { ipSecIkeAssociation  6 }

   ipSecIkePeerEndpointEntry OBJECT-TYPE
     SYNTAX IpSecIkePeerEndpointEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecIkePeerEndpointPrid }
     UNIQUENESS {
       ipSecIkePeerEndpointIdentityType,
       ipSecIkePeerEndpointIdentityValue,
       ipSecIkePeerEndpointAddressType,
       ipSecIkePeerEndpointAddress,
       ipSecIkePeerEndpointCredentialSetId
       }
     ::= { ipSecIkePeerEndpointTable 1 }

   Li, et al            Expires August, 2002                       53
                    IPsec Policy Information Base      February, 2002



     IpSecIkePeerEndpointEntry ::= SEQUENCE {
        ipSecIkePeerEndpointPrid InstanceId,
        ipSecIkePeerEndpointIdentityType INTEGER,
        ipSecIkePeerEndpointIdentityValue OCTET STRING,
        ipSecIkePeerEndpointAddressType INTEGER,
        ipSecIkePeerEndpointAddress OCTET STRING,
        ipSecIkePeerEndpointCredentialSetId TagReferenceId
   }

   ipSecIkePeerEndpointPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecIkePeerEndpointEntry  1 }

   ipSecIkePeerEndpointIdentityType OBJECT-TYPE
     SYNTAX INTEGER {
       ipV4-Address(1),
       fqdn(2),
       user-Fqdn(3),
       ipV4-Subnet(4),
       ipV6-Address(5),
       ipV6-Subnet(6),
       ipV4-Address-Range(7),
       ipV6-Address-Range(8),
       der-Asn1-DN(9),
       der-Asn1-GN(10),
       key-Id(11)
       }
     STATUS current
     DESCRIPTION
   "Specifies the type of identity that MUST be provided by the peer
   in the ID payload during IKE phase one negotiation."
     ::= { ipSecIkePeerEndpointEntry  2 }

   ipSecIkePeerEndpointIdentityValue OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "Specifies the value to be matched with the ID payload provided by
   the peer during IKE phase one negotiation.

   Different Wildcards wildcard mechanisms can be used as well as the
   prefix notation for IPv4 addresses depending on the ID payload:

   - an IdentityValue of "*@company.com" will match an user FQDN ID
   payload of "JDOE@COMPANY.COM"

   - an IdentityValue of "*.company.com" will match a FQDN ID payload
   of "WWW.COMPANY.COM"

   Li, et al            Expires August, 2002                       54
                    IPsec Policy Information Base      February, 2002



   - an IdentityValue of "cn=*,ou=engineering,o=company,c=us" will
   match a DER DN ID payload of "cn=John Doe, ou=engineering,
   o=company, c=us"

   - an IdentityValue of "193.190.125.0/24" will match an IPv4
   address ID payload of 193.190.125.10.

   - an IdentityValue of "193.190.125.*" will also match an IPv4
   address ID payload of 193.190.125.10.

   The above wildcard mechanisms MUST be supported for all ID
   payloads supported by the local IKE entity.  The character "*"
   replaces 0 or multiple instances of any character."
     ::= { ipSecIkePeerEndpointEntry  3 }

   ipSecIkePeerEndpointAddressType OBJECT-TYPE
     SYNTAX INTEGER {
       ipV4(1),
       ipV6(2)
       }
     STATUS current
     DESCRIPTION
   "Specifies IKE peer endpoint address type. This attribute MUST be
   ignored if ipSecIkeRuleAutoStart is false."
     ::= { ipSecIkePeerEndpointEntry  4 }

   ipSecIkePeerEndpointAddress OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "Specifies an endpoint address with which this PEP establishes IKE
   association. This attribute is used only when the IKE association
   is to be started automatically. Hence, this attribute MUST be
   ignored if ipSecIkeRuleAutoStart is false."
     ::= { ipSecIkePeerEndpointEntry  5 }

   ipSecIkePeerEndpointCredentialSetId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecCredentialSetSetId }
     STATUS current
     DESCRIPTION
   "Identifies a set of credentials. Any one of the credentials in
   the set is acceptable as the IKE peer credential."
     ::= { ipSecIkePeerEndpointEntry  6 }


   --
   --
   -- The ipSecCredentialSetTable
   --

   ipSecCredentialSetTable OBJECT-TYPE

   Li, et al            Expires August, 2002                       55
                    IPsec Policy Information Base      February, 2002


     SYNTAX SEQUENCE OF IpSecCredentialSetEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies credential sets.

   For IKE peer credentials, any one of the credentials in the set is
   acceptable as peer credential during IEK phase 1 negotiation. For
   IKE local credentials, any one of the credentials in the set can
   be used in IKE phase 1 negotiation."
     ::= { ipSecCredential  1 }

   ipSecCredentialSetEntry OBJECT-TYPE
     SYNTAX IpSecCredentialSetEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecCredentialSetPrid }
     UNIQUENESS {
       ipSecCredentialSetPrid,
       ipSecCredentialSetSetId,
       ipSecCredentialSetCredentialId
       }
     ::= { ipSecCredentialSetTable 1 }

     IpSecCredentialSetEntry ::= SEQUENCE {
        ipSecCredentialSetPrid InstanceId,
        ipSecCredentialSetSetId TagId,
        ipSecCredentialSetCredentialId ReferenceId
   }

   ipSecCredentialSetPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecCredentialSetEntry  1 }

   ipSecCredentialSetSetId OBJECT-TYPE
     SYNTAX TagId
     STATUS current
     DESCRIPTION
   "A credential set is composed of one or more credentials. Each
   credential belonging to the same set has the same
   CredentialSetId."
     ::= { ipSecCredentialSetEntry  2 }

   ipSecCredentialSetCredentialId OBJECT-TYPE
     SYNTAX ReferenceId
     PIB-REFERENCES    {ipSecCredentialEntry }
     STATUS current
     DESCRIPTION

   Li, et al            Expires August, 2002                       56
                    IPsec Policy Information Base      February, 2002


   "A pointer to a valid instance in the ipSecCredentialTable."
     ::= { ipSecCredentialSetEntry  3 }


   --
   --
   -- The ipSecCredentialTable
   --

   ipSecCredentialTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecCredentialEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies credentials."
     ::= { ipSecCredential  2 }

   ipSecCredentialEntry OBJECT-TYPE
     SYNTAX IpSecCredentialEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecCredentialPrid }
     UNIQUENESS {
       ipSecCredentialCredentialType,
       ipSecCredentialFieldsId,
       ipSecCredentialCrlDistributionPoint
       }
     ::= { ipSecCredentialTable 1 }

     IpSecCredentialEntry ::= SEQUENCE {
        ipSecCredentialPrid InstanceId,
        ipSecCredentialCredentialType INTEGER,
        ipSecCredentialFieldsId TagReferenceId,
        ipSecCredentialCrlDistributionPoint OCTET STRING
   }

   ipSecCredentialPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecCredentialEntry  1 }

   ipSecCredentialCredentialType OBJECT-TYPE
     SYNTAX INTEGER {
       certificateX509(1),
       kerberos-ticket(2)
       }
     STATUS current
     DESCRIPTION
   "Specifies the type of credential to be matched."

   Li, et al            Expires August, 2002                       57
                    IPsec Policy Information Base      February, 2002


     ::= { ipSecCredentialEntry  2 }

   ipSecCredentialFieldsId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecCredentialFieldsSetId }
     STATUS current
     DESCRIPTION
   "Identifies a group of matching criteria to be used for the peer
   credential. The identified criteria MUST all be satisfied."
     ::= { ipSecCredentialEntry  3 }

   ipSecCredentialCrlDistributionPoint OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "When credential type is certificate X509, this attribute
   identifies the Certificate Revocation List (CRL) distribution
   point for this credential."
     ::= { ipSecCredentialEntry  4 }


   --
   --
   -- The ipSecCredentialFieldsTable
   --

   ipSecCredentialFieldsTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecCredentialFieldsEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies sets of credential sub-fields and their values to be
   matched against. "
     ::= { ipSecCredential  3 }

   ipSecCredentialFieldsEntry OBJECT-TYPE
     SYNTAX IpSecCredentialFieldsEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecCredentialFieldsPrid }
     UNIQUENESS {
       ipSecCredentialFieldsName,
       ipSecCredentialFieldsValue,
       ipSecCredentialFieldsSetId
       }
     ::= { ipSecCredentialFieldsTable 1 }

     IpSecCredentialFieldsEntry ::= SEQUENCE {
        ipSecCredentialFieldsPrid InstanceId,
        ipSecCredentialFieldsName OCTET STRING,
        ipSecCredentialFieldsValue OCTET STRING,
        ipSecCredentialFieldsSetId TagId

   Li, et al            Expires August, 2002                       58
                    IPsec Policy Information Base      February, 2002


   }

   ipSecCredentialFieldsPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecCredentialFieldsEntry  1 }

   ipSecCredentialFieldsName OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "Specifies the sub-field of the credential to match with. This is
   the string representation of a X.509 certificate attribute, e.g.:
   "serialNumber",  "issuerName", "subjectName", etc..
   "
     ::= { ipSecCredentialFieldsEntry  2 }

   ipSecCredentialFieldsValue OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "Specifies the value to match with for the sub-field identified by
   ipSecCredentialFieldsName. A wildcard mechanism can be used in the
   Value string. E.g., if the Name is "subjectName" then a Value of
   "cn=*,ou=engineering,o=foo,c=be" will match successfully a
   certificate whose subject attribute is "cn=Jane Doe,
   ou=engineering, o=foo, c=be".  The wildcard character '*' can be
   used to represent 0 or several characters."
     ::= { ipSecCredentialFieldsEntry  3 }

   ipSecCredentialFieldsSetId OBJECT-TYPE
     SYNTAX TagId
     STATUS current
     DESCRIPTION
   "Specifies the set this criteria belongs to. All criteria within a
   set MUST all be satisfied."
     ::= { ipSecCredentialFieldsEntry  4 }


   --
   --
   -- The ipSecSelectorSetTable
   --

   ipSecSelectorSetTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecSelectorSetEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IPsec selector sets."

   Li, et al            Expires August, 2002                       59
                    IPsec Policy Information Base      February, 2002


     ::= { ipSecSelector  1 }

   ipSecSelectorSetEntry OBJECT-TYPE
     SYNTAX IpSecSelectorSetEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecSelectorSetPrid }
     UNIQUENESS {
       ipSecSelectorSetSelectorSetId,
       ipSecSelectorSetSelectorId,
       ipSecSelectorSetOrder
       }
     ::= { ipSecSelectorSetTable 1 }

     IpSecSelectorSetEntry ::= SEQUENCE {
        ipSecSelectorSetPrid InstanceId,
        ipSecSelectorSetSelectorSetId TagId,
        ipSecSelectorSetSelectorId Prid,
        ipSecSelectorSetOrder Unsigned16
   }

   ipSecSelectorSetPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecSelectorSetEntry  1 }

   ipSecSelectorSetSelectorSetId OBJECT-TYPE
     SYNTAX TagId
     STATUS current
     DESCRIPTION
   "An IPsec selector set is composed of one or more IPsec selectors.
   Each selector belonging to the same set has the same
   SelectorSetId."
     ::= { ipSecSelectorSetEntry  2 }

   ipSecSelectorSetSelectorId OBJECT-TYPE
     SYNTAX Prid
     STATUS current
     DESCRIPTION
   "A pointer to a valid instance in another table that describes
   selectors. To use selectors defined in this IPsec PIB module, this
   attribute MUST point to an instance in ipSecSelectorTable. This
   attribute may also point to an instance in a selector or filter
   table defined in other PIB modules."
     ::= { ipSecSelectorSetEntry  3 }

   ipSecSelectorSetOrder OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current

   Li, et al            Expires August, 2002                       60
                    IPsec Policy Information Base      February, 2002


     DESCRIPTION
   "An integer that specifies the precedence order of the selectors
   identified by ipSecSelectorId within a selector set. The selector
   set is identified by ipSecSelectorSetId. A smaller integer value
   indicates a higher preference. All selectors constructed from the
   instance pointed by ipSecSelectorId have the same order."
     ::= { ipSecSelectorSetEntry  4 }


   --
   --
   -- The ipSecSelectorTable
   --

   ipSecSelectorTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecSelectorEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IPsec selectors. Each row in the selector table
   represents multiple selectors. These selectors are obtained as
   follows:

   1. Substitute the ipSecSelectorSrcAddressGroupId with all the IP
   addresses from the ipSecAddressTable whose ipSecAddressGroupId
   matches the ipSecSelectorSrcAddressGroupId.

   2. Substitute the ipSecSelectorDstAddressGroupId with all the IP
   addresses from the ipSecAddressTable whose ipSecAddressGroupId
   matches the ipSecSelectorDstAddressGroupId.

   3. Substitute the ipSecSelectorSrcPortGroupId with all the ports
   or ranges of port whose ipSecL4PortGroupId matches the
   ipSecSelectorSrcPortGroupId.

   4. Substitute the ipSecSelectorDstPortGroupId with all the ports
   or ranges of port whose ipSecL4PortGroupId matches the
   ipSecSelectorDstPortGroupId.

   5. Construct all the possible combinations of the above four
   fields. Then add to the combinations the ipSecSelectorProtocol,
   ipSecSelectorDscp and ipSecSelectorFlowLabel attributes to form
   all the selectors.el attributes to form the list of selectors.

   The relative order of the selectors constructed from a single row
   is unspecified. "
     ::= { ipSecSelector  2 }

   ipSecSelectorEntry OBJECT-TYPE
     SYNTAX IpSecSelectorEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"

   Li, et al            Expires August, 2002                       61
                    IPsec Policy Information Base      February, 2002


     PIB-INDEX { ipSecSelectorPrid }
     UNIQUENESS {
       ipSecSelectorSrcAddressGroupId,
       ipSecSelectorSrcPortGroupId,
       ipSecSelectorDstAddressGroupId,
       ipSecSelectorDstPortGroupId,
       ipSecSelectorProtocol,
       ipSecSelectorDscp,
       ipSecSelectorFlowLabel
       }
     ::= { ipSecSelectorTable 1 }

     IpSecSelectorEntry ::= SEQUENCE {
        ipSecSelectorPrid InstanceId,
        ipSecSelectorSrcAddressGroupId TagReferenceId,
        ipSecSelectorSrcPortGroupId TagReferenceId,
        ipSecSelectorDstAddressGroupId TagReferenceId,
        ipSecSelectorDstPortGroupId TagReferenceId,
        ipSecSelectorProtocol INTEGER,
        ipSecSelectorDscp INTEGER,
        ipSecSelectorFlowLabel OCTET STRING
   }

   ipSecSelectorPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecSelectorEntry  1 }

   ipSecSelectorSrcAddressGroupId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecAddressGroupId }
     STATUS current
     DESCRIPTION
   "Indicates source addresses. All addresses in ipSecAddressTable
   whose ipSecAddressGroupId matches this value are included as
   source addresses.

   A value of zero indicates wildcard address, i.e., any address
   matches."
     ::= { ipSecSelectorEntry  2 }

   ipSecSelectorSrcPortGroupId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecL4PortGroupId }
     STATUS current
     DESCRIPTION
   "Indicates source layer 4 port numbers. All ports in ipSecL4Port
   whose ipSecL4PortGroupId matches this value are included.



   Li, et al            Expires August, 2002                       62
                    IPsec Policy Information Base      February, 2002


   A value of zero indicates wildcard port, i.e., any port number
   matches."
     ::= { ipSecSelectorEntry  3 }

   ipSecSelectorDstAddressGroupId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecAddressGroupId }
     STATUS current
     DESCRIPTION
   "Indicates destination addresses. All addresses in
   ipSecAddressTable whose ipSecAddressGroupId matches this value are
   included as destination addresses.

   A value of zero indicates wildcard address, i.e., any address
   matches."
     ::= { ipSecSelectorEntry  4 }

   ipSecSelectorDstPortGroupId OBJECT-TYPE
     SYNTAX TagReferenceId
     PIB-TAG    { ipSecL4PortGroupId }
     STATUS current
     DESCRIPTION
   "Indicates destination layer 4 port numbers. All ports in
   ipSecL4Port whose ipSecL4PortGroupId matches this value are
   included.

   A value of zero indicates wildcard port, i.e., any port number
   matches."
     ::= { ipSecSelectorEntry  5 }

   ipSecSelectorProtocol OBJECT-TYPE
     SYNTAX INTEGER (0..255)
     STATUS current
     DESCRIPTION
   "Specifies IP protocol to match against a packet's protocol. A
   value of zero indicates wildcard protocol, i.e., any protocol
   matches."
     ::= { ipSecSelectorEntry  6 }

   ipSecSelectorDscp OBJECT-TYPE
     SYNTAX INTEGER (-1..63)
     STATUS current
     DESCRIPTION
   "Specifies the DSCP value to match against the DSCP in a packet
   header. A value of -1 indicates match all."
     ::= { ipSecSelectorEntry  7 }

   ipSecSelectorFlowLabel OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION



   Li, et al            Expires August, 2002                       63
                    IPsec Policy Information Base      February, 2002


   "Specifies the Flow Label to match against the Flow Label field in
   the IPv6 header of a packet. This attribute MUST be a zero length
   OCTET STRING when specifying selectors for IPv4 packets."
     ::= { ipSecSelectorEntry  8 }


   --
   --
   -- The ipSecAddressTable
   --

   ipSecAddressTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecAddressEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IP addresses. To specify a single IP address,
   ipSecAddressAddrMin MUST be specified. To specify a range of
   addresses, both ipSecAddressAddrMin and ipSecAddressAddrMax MUST
   be specified. To specify a subnet, both ipSecAddressAddrMin and
   ipSecAddressAddrMask MUST be specified. "
     ::= { ipSecSelector  3 }

   ipSecAddressEntry OBJECT-TYPE
     SYNTAX IpSecAddressEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecAddressPrid }
     UNIQUENESS {
       ipSecAddressAddressType,
       ipSecAddressAddrMask,
       ipSecAddressAddrMin,
       ipSecAddressAddrMax,
       ipSecAddressGroupId
       }
     ::= { ipSecAddressTable 1 }

     IpSecAddressEntry ::= SEQUENCE {
        ipSecAddressPrid InstanceId,
        ipSecAddressAddressType INTEGER,
        ipSecAddressAddrMask OCTET STRING,
        ipSecAddressAddrMin OCTET STRING,
        ipSecAddressAddrMax OCTET STRING,
        ipSecAddressGroupId TagId
   }

   ipSecAddressPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."

   Li, et al            Expires August, 2002                       64
                    IPsec Policy Information Base      February, 2002


     ::= { ipSecAddressEntry  1 }

   ipSecAddressAddressType OBJECT-TYPE
     SYNTAX INTEGER {
       ipV4-Address(1),
       fqdn(2),
       user-Fqdn(3),
       ipV4-Subnet(4),
       ipV6-Address(5),
       ipV6-Subnet(6),
       ipV4-Address-Range(7),
       ipV6-Address-Range(8),
       der-Asn1-DN(9),
       der-Asn1-GN(10),
       key-Id(11)
       }
     STATUS current
     DESCRIPTION
   "Specifies the address type. "
     ::= { ipSecAddressEntry  2 }

   ipSecAddressAddrMask OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "A mask for the matching of the IP address. A zero bit in the mask
   means that the corresponding bit in the address always matches.

   This attribute MUST be ignored when ipSecAddressAddressType is not
   of IPv4 or IPv6 type."
     ::= { ipSecAddressEntry  3 }

   ipSecAddressAddrMin OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "Specifies an IP address. "
     ::= { ipSecAddressEntry  4 }

   ipSecAddressAddrMax OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "If a range of addresses is used then this specifies the ending
   address. The type of this address must be the same as the
   ipSecAddressAddrMin.

   If no range is specified then this attribute MUST be a zero length
   OCTET STRING."
     ::= { ipSecAddressEntry  5 }

   ipSecAddressGroupId OBJECT-TYPE
     SYNTAX TagId

   Li, et al            Expires August, 2002                       65
                    IPsec Policy Information Base      February, 2002


     STATUS current
     DESCRIPTION
   "Specifies the group this IP address, address range or subnet
   address belongs to."
     ::= { ipSecAddressEntry  6 }


   --
   --
   -- The ipSecL4PortTable
   --

   ipSecL4PortTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecL4PortEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies layer four port numbers."
     ::= { ipSecSelector  4 }

   ipSecL4PortEntry OBJECT-TYPE
     SYNTAX IpSecL4PortEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecL4PortPrid }
     UNIQUENESS {
       ipSecL4PortPortMin,
       ipSecL4PortPortMax,
       ipSecL4PortGroupId
       }
     ::= { ipSecL4PortTable 1 }

     IpSecL4PortEntry ::= SEQUENCE {
        ipSecL4PortPrid InstanceId,
        ipSecL4PortPortMin Unsigned16,
        ipSecL4PortPortMax Unsigned16,
        ipSecL4PortGroupId TagId
   }

   ipSecL4PortPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecL4PortEntry  1 }

   ipSecL4PortPortMin OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION


   Li, et al            Expires August, 2002                       66
                    IPsec Policy Information Base      February, 2002


   "Specifies a layer 4 port or the first layer 4 port number of a
   range of ports. The value of this attribute must be equal or less
   than that of ipSecL4PortPortMax.

   A value of zero indicates any port matches."
     ::= { ipSecL4PortEntry  2 }

   ipSecL4PortPortMax OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "Specifies the last layer 4 port in the range. If only a single
   port is specified, the value of this attribute must be equal to
   that of ipSecL4PortPortMin. Otherwise, the value of this attribute
   MUST be greater than that specified by ipSecL4PortPortMin.

   If ipSecL4PortPortMin is zero, this attribute MUST be ignored."
     ::= { ipSecL4PortEntry  3 }

   ipSecL4PortGroupId OBJECT-TYPE
     SYNTAX TagId
     STATUS current
     DESCRIPTION
   "Specifies the group this port or port range belongs to."
     ::= { ipSecL4PortEntry  4 }


   --
   --
   -- The ipSecIpsoFilterSetTable
   --

   ipSecIpsoFilterSetTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecIpsoFilterSetEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IPSO filter sets."
     ::= { ipSecSelector  5 }

   ipSecIpsoFilterSetEntry OBJECT-TYPE
     SYNTAX IpSecIpsoFilterSetEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecIpsoFilterSetPrid }
     UNIQUENESS {
       ipSecIpsoFilterSetFilterSetId,
       ipSecIpsoFilterSetFilterId,
       ipSecIpsoFilterSetOrder
       }
     ::= { ipSecIpsoFilterSetTable 1 }


   Li, et al            Expires August, 2002                       67
                    IPsec Policy Information Base      February, 2002


     IpSecIpsoFilterSetEntry ::= SEQUENCE {
        ipSecIpsoFilterSetPrid InstanceId,
        ipSecIpsoFilterSetFilterSetId TagId,
        ipSecIpsoFilterSetFilterId ReferenceId,
        ipSecIpsoFilterSetOrder Unsigned16
   }

   ipSecIpsoFilterSetPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecIpsoFilterSetEntry  1 }

   ipSecIpsoFilterSetFilterSetId OBJECT-TYPE
     SYNTAX TagId
     STATUS current
     DESCRIPTION
   "An IPSO filter set is composed of one or more IPSO filters. Each
   filter belonging to the same set has the same FilterSetId."
     ::= { ipSecIpsoFilterSetEntry  2 }

   ipSecIpsoFilterSetFilterId OBJECT-TYPE
     SYNTAX ReferenceId
     PIB-REFERENCES    {ipSecIpsoFilterEntry }
     STATUS current
     DESCRIPTION
   "A pointer to a valid instance in the ipSecIpsoFilterTable."
     ::= { ipSecIpsoFilterSetEntry  3 }

   ipSecIpsoFilterSetOrder OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "An integer that specifies the precedence order of the filter
   identified by ipSecIpsoFilterSetFilterId within a filter set. The
   filter set is identified by ipSecIpsoFilterSetFilterSetId. A
   smaller integer value indicates a higher preference."
     ::= { ipSecIpsoFilterSetEntry  4 }


   --
   --
   -- The ipSecIpsoFilterTable
   --

   ipSecIpsoFilterTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecIpsoFilterEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies IPSO filters."

   Li, et al            Expires August, 2002                       68
                    IPsec Policy Information Base      February, 2002


     ::= { ipSecSelector  6 }

   ipSecIpsoFilterEntry OBJECT-TYPE
     SYNTAX IpSecIpsoFilterEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecIpsoFilterPrid }
     UNIQUENESS {
       ipSecIpsoFilterMatchConditionType,
       ipSecIpsoFilterClassificationLevel,
       ipSecIpsoFilterProtectionAuthority
       }
     ::= { ipSecIpsoFilterTable 1 }

     IpSecIpsoFilterEntry ::= SEQUENCE {
        ipSecIpsoFilterPrid InstanceId,
        ipSecIpsoFilterMatchConditionType INTEGER,
        ipSecIpsoFilterClassificationLevel INTEGER,
        ipSecIpsoFilterProtectionAuthority INTEGER
   }

   ipSecIpsoFilterPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecIpsoFilterEntry  1 }

   ipSecIpsoFilterMatchConditionType OBJECT-TYPE
     SYNTAX INTEGER {
       classificationLevel(1),
       protectionAuthority(2)
       }
     STATUS current
     DESCRIPTION
   "Specifies the IPSO header field to be matched."
     ::= { ipSecIpsoFilterEntry  2 }

   ipSecIpsoFilterClassificationLevel OBJECT-TYPE
     SYNTAX INTEGER {
       topSecret(61),
       secret(90),
       confidential(150),
       unclassified(171)
       }
     STATUS current
     DESCRIPTION
   "Specifies the value for classification level to be matched
   against. This attribute MUST be ignored if
   ipSecIpsoFilterMatchConditionType is not 1 (classificationLevel)."
     ::= { ipSecIpsoFilterEntry  3 }

   Li, et al            Expires August, 2002                       69
                    IPsec Policy Information Base      February, 2002



   ipSecIpsoFilterProtectionAuthority OBJECT-TYPE
     SYNTAX INTEGER {
       genser(0),
       siop-esi(1),
       sci(2),
       nsa(3),
       doe(4)
       }
     STATUS current
     DESCRIPTION
   "Specifies the value for protection authority to be matched
   against. This attribute MUST be ignored if
   ipSecIpsoFilterMatchConditionType is not 2 (protectionAuthority).
   "
     ::= { ipSecIpsoFilterEntry  4 }


   --
   --
   -- The ipSecRuleTimePeriodTable
   --

   ipSecRuleTimePeriodTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecRuleTimePeriodEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies the time periods during which a policy rule is valid.
   The values of the first five attributes in a row are ANDed
   together to determine the validity period(s). If any of the five
   attributes is not present, it is treated as having value always
   enabled.  "
     ::= { ipSecPolicyTimePeriod  1 }

   ipSecRuleTimePeriodEntry OBJECT-TYPE
     SYNTAX IpSecRuleTimePeriodEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecRuleTimePeriodPrid }
     UNIQUENESS {
       ipSecRuleTimePeriodTimePeriod,
       ipSecRuleTimePeriodMonthOfYearMask,
       ipSecRuleTimePeriodDayOfMonthMask,
       ipSecRuleTimePeriodDayOfWeekMask,
       ipSecRuleTimePeriodTimeOfDayMask,
       ipSecRuleTimePeriodLocalOrUtcTime
       }
     ::= { ipSecRuleTimePeriodTable 1 }

     IpSecRuleTimePeriodEntry ::= SEQUENCE {
        ipSecRuleTimePeriodPrid InstanceId,

   Li, et al            Expires August, 2002                       70
                    IPsec Policy Information Base      February, 2002


        ipSecRuleTimePeriodTimePeriod OCTET STRING,
        ipSecRuleTimePeriodMonthOfYearMask OCTET STRING,
        ipSecRuleTimePeriodDayOfMonthMask OCTET STRING,
        ipSecRuleTimePeriodDayOfWeekMask OCTET STRING,
        ipSecRuleTimePeriodTimeOfDayMask OCTET STRING,
        ipSecRuleTimePeriodLocalOrUtcTime INTEGER
   }

   ipSecRuleTimePeriodPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index to uniquely identify an instance of this class"
     ::= { ipSecRuleTimePeriodEntry  1 }

   ipSecRuleTimePeriodTimePeriod OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "An octet string that identifies an overall range of calendar
   dates and times over which a policy rule is valid.  It reuses the
   format for an explicit time period defined in RFC 2445 : a string
   representing a starting date and time, in which the character 'T'
   indicates the beginning of the time portion, followed by the
   solidus character '/', followed by a similar string representing
   an end date and time.  The first date indicates the beginning of
   the range, while the second date indicates the end.  Thus, the
   second date and time must be later than the first.  Date/times are
   expressed as substrings of the form yyyymmddThhmmss.

   There are also two special cases:

   -  If the first date/time is replaced with the string
   THISANDPRIOR, then the property indicates that a policy rule is
   valid [from now] until the date/time that appears after the '/'.

   - If the second date/time is replaced with the string
   THISANDFUTURE, then the property indicates that a policy rule
   becomes valid on the date/time that appears before the '/', and
   remains valid from that point on.
   "
     ::= { ipSecRuleTimePeriodEntry  2 }

   ipSecRuleTimePeriodMonthOfYearMask OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "An octet string that specifies which months the policy is valid
   for.  The octet string is structured as follows:

   - a 4-octet length field, indicating the length of the entire
   octet string; this field is always set to 0x00000006 for this
   property;

   Li, et al            Expires August, 2002                       71
                    IPsec Policy Information Base      February, 2002



   - a 2-octet field consisting of 12 bits identifying the 12 months
   of the year, beginning with January and ending with December,
   followed by 4 bits that are always set to '0'.  For each month,
   the value '1' indicates that the policy is valid for that month,
   and the value '0' indicates that it is not valid.

    If this property is omitted, then the policy rule is treated as
   valid for all twelve months."
     ::= { ipSecRuleTimePeriodEntry  3 }

   ipSecRuleTimePeriodDayOfMonthMask OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "An octet string that specifies which days of the month the policy
   is valid for. The octet string is structured as follows:

   -a 4-octet length field, indicating the length of the entire octet
   string; this field is always set to 0x0000000C for this property;

   -an 8-octet field consisting of 31 bits identifying the days of
   the month counting from the beginning, followed by 31 more bits
   identifying the days of the month counting from the end, followed
   by 2 bits that are always set to '0'.  For each day, the value '1'
   indicates that the policy is valid for that day, and the value '0'
   indicates that it is not valid.

   For months with fewer than 31 days, the digits corresponding to
   days that the months do not have (counting in both directions) are
   ignored.
   "
     ::= { ipSecRuleTimePeriodEntry  4 }

   ipSecRuleTimePeriodDayOfWeekMask OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "An octet string that specifies which days of the week the policy
   is valid for. The octet string is structured as follows:

   - a 4-octet length field, indicating the length of the entire
   octet string; this field is always set to 0x00000005 for this
   property;

   - a 1-octet field consisting of 7 bits identifying the 7 days of
   the week, beginning with Sunday and ending with Saturday, followed
   by 1 bit that is always set to '0'.  For each day of the week, the
   value '1' indicates that the policy is valid for that day, and the
   value '0' indicates that it is not valid.
   "
     ::= { ipSecRuleTimePeriodEntry  5 }


   Li, et al            Expires August, 2002                       72
                    IPsec Policy Information Base      February, 2002


   ipSecRuleTimePeriodTimeOfDayMask OBJECT-TYPE
     SYNTAX OCTET STRING
     STATUS current
     DESCRIPTION
   "An octet string that specifies a range of times in a day the
   policy is valid for. It is formatted as follows:

   A  time  string beginning with the character 'T', followed by the
   solidus character '/', followed by a second time string.  The
   first time indicates the beginning of the range, while the second
   time indicates the end.  Times are expressed as substrings of the
   form Thhmmss.

   The second substring always identifies a later time than the first
   substring.  To allow for ranges that span midnight, however, the
   value of the second string may be smaller than the value of the
   first substring.  Thus, T080000/T210000 identifies the range from
   0800 until 2100, while T210000/T080000 identifies the range from
   2100 until 0800 of the following day."
     ::= { ipSecRuleTimePeriodEntry  6 }

   ipSecRuleTimePeriodLocalOrUtcTime OBJECT-TYPE
     SYNTAX INTEGER {
       localTime(1),
       utcTime(2)
       }
     STATUS current
     DESCRIPTION
   "This property indicates whether the times represented in this
   table represent local times or UTC times.  There is no provision
   for mixing of local times and UTC times:  the value of this
   property applies to all of the other time-related properties."
     ::= { ipSecRuleTimePeriodEntry  7 }


   --
   --
   -- The ipSecRuleTimePeriodSetTable
   --

   ipSecRuleTimePeriodSetTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecRuleTimePeriodSetEntry
     PIB-ACCESS install
     STATUS current
     DESCRIPTION
   "Specifies time period sets. The ipSecRuleTimePeriodTable can
   specify only a single time period within a day. This table enables
   the specification of multiple time periods within a day by
   grouping them into one set. "
     ::= { ipSecPolicyTimePeriod  2 }

   ipSecRuleTimePeriodSetEntry OBJECT-TYPE
     SYNTAX IpSecRuleTimePeriodSetEntry

   Li, et al            Expires August, 2002                       73
                    IPsec Policy Information Base      February, 2002


     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecRuleTimePeriodSetPrid }
     UNIQUENESS {
       ipSecRuleTimePeriodSetRuleTimePeriodSetId,
       ipSecRuleTimePeriodSetRuleTimePeriodId
       }
     ::= { ipSecRuleTimePeriodSetTable 1 }

     IpSecRuleTimePeriodSetEntry ::= SEQUENCE {
        ipSecRuleTimePeriodSetPrid InstanceId,
        ipSecRuleTimePeriodSetRuleTimePeriodSetId TagId,
        ipSecRuleTimePeriodSetRuleTimePeriodId ReferenceId
   }

   ipSecRuleTimePeriodSetPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index to uniquely identify an instance of this class"
     ::= { ipSecRuleTimePeriodSetEntry  1 }

   ipSecRuleTimePeriodSetRuleTimePeriodSetId OBJECT-TYPE
     SYNTAX TagId
     STATUS current
     DESCRIPTION
   "An integer that uniquely identifies an ipSecRuleTimePeriod set. "
     ::= { ipSecRuleTimePeriodSetEntry  2 }

   ipSecRuleTimePeriodSetRuleTimePeriodId OBJECT-TYPE
     SYNTAX ReferenceId
     PIB-REFERENCES    {ipSecRuleTimePeriodEntry }
     STATUS current
     DESCRIPTION
   "An integer that identifies an ipSecRuleTimePeriod, specified by
   ipSecRuleTimePeriodPrid in the ipSecRuleTimePeriodTable, that is
   included in this set."
     ::= { ipSecRuleTimePeriodSetEntry  3 }


   --
   --
   -- The ipSecIfCapsTable
   --

   ipSecIfCapsTable OBJECT-TYPE
     SYNTAX SEQUENCE OF IpSecIfCapsEntry
     PIB-ACCESS notify
     STATUS current
     DESCRIPTION
   "Specifies capabilities that may be associated with an interface
   of a specific type. The instances of this table are referenced by

   Li, et al            Expires August, 2002                       74
                    IPsec Policy Information Base      February, 2002


   the frwkIfCapSetCapability attribute of the frwkIfCapSetTable [FR-
   PIB]."
     ::= { ipSecIfCapability  1 }

   ipSecIfCapsEntry OBJECT-TYPE
     SYNTAX IpSecIfCapsEntry
     STATUS current
     DESCRIPTION
   "Specifies an instance of this class"
     PIB-INDEX { ipSecIfCapsPrid }
     UNIQUENESS {
       ipSecIfCapsDirection,
       ipSecIfCapsMaxIpSecActions,
       ipSecIfCapsMaxIkeActions
       }
     ::= { ipSecIfCapsTable 1 }

     IpSecIfCapsEntry ::= SEQUENCE {
        ipSecIfCapsPrid InstanceId,
        ipSecIfCapsDirection INTEGER,
        ipSecIfCapsMaxIpSecActions Unsigned16,
        ipSecIfCapsMaxIkeActions Unsigned16
   }

   ipSecIfCapsPrid OBJECT-TYPE
     SYNTAX InstanceId
     STATUS current
     DESCRIPTION
   "An integer index that uniquely identifies an instance of this
   class."
     ::= { ipSecIfCapsEntry  1 }

   ipSecIfCapsDirection OBJECT-TYPE
     SYNTAX INTEGER {
       in(1),
       out(2),
       bi-directional(3)
       }
     STATUS current
     DESCRIPTION
   "Specifies the direction for which this capability applies."
     ::= { ipSecIfCapsEntry  2 }

   ipSecIfCapsMaxIpSecActions OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "Specifies the maximum number of actions an IPsec action set may
   contain. IPsec action sets are specified by the
   ipSecActionSetTable.

   A value of zero indicates that there is no maximum limit."
     ::= { ipSecIfCapsEntry  3 }

   Li, et al            Expires August, 2002                       75
                    IPsec Policy Information Base      February, 2002



   ipSecIfCapsMaxIkeActions OBJECT-TYPE
     SYNTAX Unsigned16
     STATUS current
     DESCRIPTION
   "Specifies the maximum number of actions an IKE action set may
   contain. IKE action sets are specified by the
   ipSecIkeActionSetTable.

   A value of zero indicates that there is no maximum limit."
     ::= { ipSecIfCapsEntry  4 }


   --
   --
   -- Conformance Section
   --

   ipSecPolicyPibConformanceCompliances
       OBJECT IDENTIFIER ::= { ipSecPolicyPibConformance 1 }

   ipSecPolicyPibConformanceGroups
       OBJECT IDENTIFIER ::= { ipSecPolicyPibConformance 2 }

   IPsecPibCompilance MODULE-COMPLIANCE
       STATUS current
       DESCRIPTION
   "        Compliance statement"
       MODULE û- this module
           MANDATORY-GROUPS {
           ipSecRuleGroup,
           ipSecActionSetGroup,
           ipSecStaticActionGroup,
           ipSecNegotiationActionGroup,
           ipSecAssociationGroup,
           ipSecProposalSetGroup,
           ipSecProposalGroup,
           ipSecAhTransformSetGroup,
           ipSecAhTransformGroup,
           ipSecEspTransformSetGroup,
           ipSecEspTransformGroup,
           ipSecCompTransformSetGroup,
           ipSecCompTransformGroup,
           ipSecIkeAssociationGroup,
           ipSecIkeProposalSetGroup,
           ipSecIkeProposalGroup,
           ipSecIkePeerEndpointGroup,
           ipSecCredentialSetGroup,
           ipSecCredentialGroup,
           ipSecCredentialFieldsGroup,
           ipSecSelectorSetGroup,
           ipSecSelectorGroup,
           ipSecAddressGroup,

   Li, et al            Expires August, 2002                       76
                    IPsec Policy Information Base      February, 2002


           ipSecL4PortGroup,
           ipSecIfCapsGroup
           }

       GROUP ipSecIkeRuleGroup
           DESCRIPTION
   "This group is mandatory if any of the following is supported: 1)
   multiple IKE phase one actions (e.g., with different exchange
   modes) are associated with an IPsec rule. These actions are to be
   tried in sequence till one success; 2) IKE phase one actions that
   start automatically."

       GROUP ipSecIkeActionSetGroup
           DESCRIPTION
   "This group is mandatory if any of the following is supported: 1)
   multiple IKE phase one actions (e.g., with different exchange
   modes) are associated with an IPsec rule. These actions are to be
   tried in sequence till one success; 2) IKE phase one actions that
   start automatically."

       GROUP ipSecIpsoFilterSetGroup
           DESCRIPTION
   "This group is mandatory if IPSO filter is supported."

       GROUP ipSecIpsoFilterGroup
           DESCRIPTION
   "This group is mandatory if IPSO filter is supported."

       GROUP ipSecRuleTimePeriodGroup
           DESCRIPTION
   "This group is mandatory if policy scheduling is supported."

       GROUP ipSecRuleTimePeriodSetGroup
           DESCRIPTION
   "This group is mandatory if policy scheduling is supported."

       OBJECT ipSecRuleipSecIpsoFilterSetId
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecRuleLimitNegotiation
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecRuleAutoStart
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecRuleIpSecRuleTimePeriodGroupId
       PIB-MIN-ACCESS not-accessible

   Li, et al            Expires August, 2002                       77
                    IPsec Policy Information Base      February, 2002


       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecActionSetDoActionLogging
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecActionSetDoPacketLogging
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecAssociationMinLifetimeSeconds
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecAssociationMinLifetimeKilobytes
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecAssociationIdleDurationSeconds
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecAssociationVendorId
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecAssociationUseKeyExchangeGroup
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecAssociationGranularity
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecAhTransformUseReplayPrevention
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecAhTransformReplayPreventionWindowSize
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"


   Li, et al            Expires August, 2002                       78
                    IPsec Policy Information Base      February, 2002


       OBJECT ipSecAhTransformVendorId
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecEspTransformCipherKeyRounds
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecEspTransformCipherKeyLength
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecEspTransformUseReplayPrevention
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecEspTransformReplayPreventionWindowSize
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecEspTransformVendorId
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecCompTransformDictionarySize
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecCompTransformPrivateAlgorithm
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecCompTransformVendorId
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecIkeAssociationMinLiftetimeSeconds
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecIkeAssociationMinLifetimeKilobytes
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION

   Li, et al            Expires August, 2002                       79
                    IPsec Policy Information Base      February, 2002


   "              Support of this attribute is optional"

       OBJECT ipSecIkeAssociationIdleDurationSeconds
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecIkeAssociationPresharedKey
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecIkeAssociationVendorId
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecIkeAssociationAggressiveModeGroupId
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecIkeAssociationLocalCredentialId
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecIkeAssociationDoActionLogging
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecIkeProposalPrfAlgorithm
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecIkeProposalVendorId
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecIkePeerEndpointAddressType
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecIkePeerEndpointAddress
       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecIfCapsMaxIkeActions

   Li, et al            Expires August, 2002                       80
                    IPsec Policy Information Base      February, 2002


       PIB-MIN-ACCESS not-accessible
       DESCRIPTION
   "              Support of this attribute is optional"

       OBJECT ipSecRuleActionExecutionStrategy
       SYNTAX INTEGER {
         doAll(1)
         }
       DESCRIPTION
   "              Support of doUntilSuccess(2) is not required"

       OBJECT ipSecStaticActionAction
       SYNTAX INTEGER {
         byPass(1),
         discard(2),
         preConfiguredTransport(4),
         preConfiguredTunnel(5)
         }
       DESCRIPTION
   "              Support of ikeRejection(3) is not required"

       ::= { ipSecPolicyPibConformanceCompliances 1 }

   ipSecRuleGroup OBJECT-GROUP
       OBJECTS {
          ipSecRuleIfName,
          ipSecRuleRoles,
          ipSecRuleDirection,
          ipSecRuleIpSecSelectorSetId,
          ipSecRuleipSecIpsoFilterSetId,
          ipSecRuleIpSecActionSetId,
          ipSecRuleActionExecutionStrategy,
          ipSecRuleOrder,
          ipSecRuleLimitNegotiation,
          ipSecRuleAutoStart,
          ipSecRuleIpSecRuleTimePeriodGroupId
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecRuleTable."
       ::= { ipSecPolicyPibConformanceGroups  1 }

   ipSecActionSetGroup OBJECT-GROUP
       OBJECTS {
          ipSecActionSetActionSetId,
          ipSecActionSetActionId,
          ipSecActionSetDoActionLogging,
          ipSecActionSetDoPacketLogging,
          ipSecActionSetOrder
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecActionSetTable."

   Li, et al            Expires August, 2002                       81
                    IPsec Policy Information Base      February, 2002


       ::= { ipSecPolicyPibConformanceGroups  2 }

   ipSecStaticActionGroup OBJECT-GROUP
       OBJECTS {
          ipSecStaticActionAction,
          ipSecStaticActionTunnelEndpointId,
          ipSecStaticActionDfHandling,
          ipSecStaticActionSpi,
          ipSecStaticActionLifetimeSeconds,
          ipSecStaticActionLifetimeKilobytes,
          ipSecStaticActionSaTransformId
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecStaticActionTable."
       ::= { ipSecPolicyPibConformanceGroups  3 }

   ipSecNegotiationActionGroup OBJECT-GROUP
       OBJECTS {
          ipSecNegotiationActionAction,
          ipSecNegotiationActionTunnelEndpointId,
          ipSecNegotiationActionDfHandling,
          ipSecNegotiationActionIpSecSecurityAssociationId,
          ipSecNegotiationActionKeyExchangeId
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecNegotiationActionTable."
       ::= { ipSecPolicyPibConformanceGroups  4 }

   ipSecAssociationGroup OBJECT-GROUP
       OBJECTS {
          ipSecAssociationMinLifetimeSeconds,
          ipSecAssociationMinLifetimeKilobytes,
          ipSecAssociationIdleDurationSeconds,
          ipSecAssociationUsePfs,
          ipSecAssociationVendorId,
          ipSecAssociationUseKeyExchangeGroup,
          ipSecAssociationDhGroup,
          ipSecAssociationGranularity,
          ipSecAssociationProposalSetId
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecAssociationTable."
       ::= { ipSecPolicyPibConformanceGroups  5 }

   ipSecProposalSetGroup OBJECT-GROUP
       OBJECTS {
          ipSecProposalSetProposalSetId,
          ipSecProposalSetProposalId,
          ipSecProposalSetOrder
          }

   Li, et al            Expires August, 2002                       82
                    IPsec Policy Information Base      February, 2002


       STATUS current
       DESCRIPTION
   "Objects from the ipSecProposalSetTable."
       ::= { ipSecPolicyPibConformanceGroups  6 }

   ipSecProposalGroup OBJECT-GROUP
       OBJECTS {
          ipSecProposalEspTransformSetId,
          ipSecProposalAhTransformSetId,
          ipSecProposalCompTransformSetId
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecProposalTable."
       ::= { ipSecPolicyPibConformanceGroups  7 }

   ipSecAhTransformSetGroup OBJECT-GROUP
       OBJECTS {
          ipSecAhTransformSetTransformSetId,
          ipSecAhTransformSetTransformId,
          ipSecAhTransformSetOrder
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecAhTransformSetTable."
       ::= { ipSecPolicyPibConformanceGroups  8 }

   ipSecAhTransformGroup OBJECT-GROUP
       OBJECTS {
          ipSecAhTransformTransformId,
          ipSecAhTransformIntegrityKey,
          ipSecAhTransformUseReplayPrevention,
          ipSecAhTransformReplayPreventionWindowSize,
          ipSecAhTransformVendorId,
          ipSecAhTransformMaxLifetimeSeconds,
          ipSecAhTransformMaxLifetimeKilobytes
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecAhTransformTable."
       ::= { ipSecPolicyPibConformanceGroups  9 }

   ipSecEspTransformSetGroup OBJECT-GROUP
       OBJECTS {
          ipSecEspTransformSetTransformSetId,
          ipSecEspTransformSetTransformId,
          ipSecEspTransformSetOrder
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecEspTransformSetTable."
       ::= { ipSecPolicyPibConformanceGroups  10 }


   Li, et al            Expires August, 2002                       83
                    IPsec Policy Information Base      February, 2002


   ipSecEspTransformGroup OBJECT-GROUP
       OBJECTS {
          ipSecEspTransformIntegrityTransformId,
          ipSecEspTransformCipherTransformId,
          ipSecEspTransformIntegrityKey,
          ipSecEspTransformCipherKey,
          ipSecEspTransformCipherKeyRounds,
          ipSecEspTransformCipherKeyLength,
          ipSecEspTransformUseReplayPrevention,
          ipSecEspTransformReplayPreventionWindowSize,
          ipSecEspTransformVendorId,
          ipSecEspTransformMaxLifetimeSeconds,
          ipSecEspTransformMaxLifetimeKilobytes
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecEspTransformTable."
       ::= { ipSecPolicyPibConformanceGroups  11 }

   ipSecCompTransformSetGroup OBJECT-GROUP
       OBJECTS {
          ipSecCompTransformSetTransformSetId,
          ipSecCompTransformSetTransformId,
          ipSecCompTransformSetOrder
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecCompTransformSetTable."
       ::= { ipSecPolicyPibConformanceGroups  12 }

   ipSecCompTransformGroup OBJECT-GROUP
       OBJECTS {
          ipSecCompTransformAlgorithm,
          ipSecCompTransformDictionarySize,
          ipSecCompTransformPrivateAlgorithm,
          ipSecCompTransformVendorId,
          ipSecCompTransformMaxLifetimeSeconds,
          ipSecCompTransformMaxLifetimeKilobytes
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecCompTransformTable."
       ::= { ipSecPolicyPibConformanceGroups  13 }

   ipSecIkeRuleGroup OBJECT-GROUP
       OBJECTS {
          ipSecIkeRuleIfName,
          ipSecIkeRuleRoles,
          ipSecIkeRuleIkeActionSetId,
          ipSecIkeRuleActionExecutionStrategy,
          ipSecIkeRuleLimitNegotiation,
          ipSecIkeRuleAutoStart,
          ipSecIkeRuleIpSecRuleTimePeriodGroupId

   Li, et al            Expires August, 2002                       84
                    IPsec Policy Information Base      February, 2002


          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecIkeRuleTable."
       ::= { ipSecPolicyPibConformanceGroups  14 }

   ipSecIkeActionSetGroup OBJECT-GROUP
       OBJECTS {
          ipSecIkeActionSetActionSetId,
          ipSecIkeActionSetActionId,
          ipSecIkeActionSetOrder
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecIkeActionSetTable."
       ::= { ipSecPolicyPibConformanceGroups  15 }

   ipSecIkeAssociationGroup OBJECT-GROUP
       OBJECTS {
          ipSecIkeAssociationMinLiftetimeSeconds,
          ipSecIkeAssociationMinLifetimeKilobytes,
          ipSecIkeAssociationIdleDurationSeconds,
          ipSecIkeAssociationExchangeMode,
          ipSecIkeAssociationUseIkeIdentityType,
          ipSecIkeAssociationUseIkeIdentityValue,
          ipSecIkeAssociationIkePeerEndpoint,
          ipSecIkeAssociationPresharedKey,
          ipSecIkeAssociationVendorId,
          ipSecIkeAssociationAggressiveModeGroupId,
          ipSecIkeAssociationLocalCredentialId,
          ipSecIkeAssociationDoActionLogging,
          ipSecIkeAssociationIkeProposalSetId
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecIkeAssociationTable."
       ::= { ipSecPolicyPibConformanceGroups  16 }

   ipSecIkeProposalSetGroup OBJECT-GROUP
       OBJECTS {
          ipSecIkeProposalSetProposalSetId,
          ipSecIkeProposalSetProposalId,
          ipSecIkeProposalSetOrder
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecIkeProposalSetTable."
       ::= { ipSecPolicyPibConformanceGroups  17 }

   ipSecIkeProposalGroup OBJECT-GROUP
       OBJECTS {
          ipSecIkeProposalMaxLifetimeSeconds,
          ipSecIkeProposalMaxLifetimeKilobytes,

   Li, et al            Expires August, 2002                       85
                    IPsec Policy Information Base      February, 2002


          ipSecIkeProposalCipherAlgorithm,
          ipSecIkeProposalHashAlgorithm,
          ipSecIkeProposalAuthenticationMethod,
          ipSecIkeProposalPrfAlgorithm,
          ipSecIkeProposalIkeDhGroup,
          ipSecIkeProposalVendorId
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecIkeProposalTable."
       ::= { ipSecPolicyPibConformanceGroups  18 }

   ipSecIkePeerEndpointGroup OBJECT-GROUP
       OBJECTS {
          ipSecIkePeerEndpointIdentityType,
          ipSecIkePeerEndpointIdentityValue,
          ipSecIkePeerEndpointAddressType,
          ipSecIkePeerEndpointAddress,
          ipSecIkePeerEndpointCredentialSetId
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecIkePeerEndpointTable."
       ::= { ipSecPolicyPibConformanceGroups  19 }

   ipSecCredentialSetGroup OBJECT-GROUP
       OBJECTS {
          ipSecCredentialSetSetId,
          ipSecCredentialSetCredentialId
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecCredentialSetTable."
       ::= { ipSecPolicyPibConformanceGroups  20 }

   ipSecCredentialGroup OBJECT-GROUP
       OBJECTS {
          ipSecCredentialCredentialType,
          ipSecCredentialFieldsId,
          ipSecCredentialCrlDistributionPoint
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecCredentialTable."
       ::= { ipSecPolicyPibConformanceGroups  21 }

   ipSecCredentialFieldsGroup OBJECT-GROUP
       OBJECTS {
          ipSecCredentialFieldsName,
          ipSecCredentialFieldsValue,
          ipSecCredentialFieldsSetId
          }
       STATUS current

   Li, et al            Expires August, 2002                       86
                    IPsec Policy Information Base      February, 2002


       DESCRIPTION
   "Objects from the ipSecCredentialFieldsTable."
       ::= { ipSecPolicyPibConformanceGroups  22 }

   ipSecSelectorSetGroup OBJECT-GROUP
       OBJECTS {
          ipSecSelectorSetSelectorSetId,
          ipSecSelectorSetSelectorId,
          ipSecSelectorSetOrder
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecSelectorSetTable."
       ::= { ipSecPolicyPibConformanceGroups  23 }

   ipSecSelectorGroup OBJECT-GROUP
       OBJECTS {
          ipSecSelectorSrcAddressGroupId,
          ipSecSelectorSrcPortGroupId,
          ipSecSelectorDstAddressGroupId,
          ipSecSelectorDstPortGroupId,
          ipSecSelectorProtocol,
          ipSecSelectorDscp,
          ipSecSelectorFlowLabel
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecSelectorTable."
       ::= { ipSecPolicyPibConformanceGroups  24 }

   ipSecAddressGroup OBJECT-GROUP
       OBJECTS {
          ipSecAddressAddressType,
          ipSecAddressAddrMask,
          ipSecAddressAddrMin,
          ipSecAddressAddrMax,
          ipSecAddressGroupId
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecAddressTable."
       ::= { ipSecPolicyPibConformanceGroups  25 }

   ipSecL4PortGroup OBJECT-GROUP
       OBJECTS {
          ipSecL4PortPortMin,
          ipSecL4PortPortMax,
          ipSecL4PortGroupId
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecL4PortTable."
       ::= { ipSecPolicyPibConformanceGroups  26 }

   Li, et al            Expires August, 2002                       87
                    IPsec Policy Information Base      February, 2002



   ipSecIpsoFilterSetGroup OBJECT-GROUP
       OBJECTS {
          ipSecIpsoFilterSetFilterSetId,
          ipSecIpsoFilterSetFilterId,
          ipSecIpsoFilterSetOrder
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecIpsoFilterSetTable."
       ::= { ipSecPolicyPibConformanceGroups  27 }

   ipSecIpsoFilterGroup OBJECT-GROUP
       OBJECTS {
          ipSecIpsoFilterMatchConditionType,
          ipSecIpsoFilterClassificationLevel,
          ipSecIpsoFilterProtectionAuthority
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecIpsoFilterTable."
       ::= { ipSecPolicyPibConformanceGroups  28 }

   ipSecRuleTimePeriodGroup OBJECT-GROUP
       OBJECTS {
          ipSecRuleTimePeriodTimePeriod,
          ipSecRuleTimePeriodMonthOfYearMask,
          ipSecRuleTimePeriodDayOfMonthMask,
          ipSecRuleTimePeriodDayOfWeekMask,
          ipSecRuleTimePeriodTimeOfDayMask,
          ipSecRuleTimePeriodLocalOrUtcTime
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecRuleTimePeriodTable."
       ::= { ipSecPolicyPibConformanceGroups  29 }

   ipSecRuleTimePeriodSetGroup OBJECT-GROUP
       OBJECTS {
          ipSecRuleTimePeriodSetRuleTimePeriodSetId,
          ipSecRuleTimePeriodSetRuleTimePeriodId
          }
       STATUS current
       DESCRIPTION
   "Objects from the ipSecRuleTimePeriodSetTable."
       ::= { ipSecPolicyPibConformanceGroups  30 }

   ipSecIfCapsGroup OBJECT-GROUP
       OBJECTS {
          ipSecIfCapsDirection,
          ipSecIfCapsMaxIpSecActions,
          ipSecIfCapsMaxIkeActions
          }

   Li, et al            Expires August, 2002                       88
                    IPsec Policy Information Base      February, 2002


       STATUS current
       DESCRIPTION
   "Objects from the ipSecIfCapsTable."
       ::= { ipSecPolicyPibConformanceGroups  31 }

END

6. Security Considerations

   Since COPS is used to carry the PIB defined in this document, the
   security and protection of the information can be provided by
   either COPS or a combination of COPS and other security protocols,
   e.g., IPsec or TLS.

7. References

   1  Bradner, S., "The Internet Standards Process -- Revision 3", BCP
      9, RFC 2026, October 1996.

   2  Bradner, S., "Key words for use in RFCs to Indicate Requirement
      Levels", BCP 14, RFC 2119, March 1997


   3.  S. Kent, R. Atkinson, "IP Authentication Header", RFC 2402,
   November 1998.

   4.  F. Dawson, D. Stenerson, "Internet Calendaring and Scheduling
   Core Object Specification (iCalendar)", RFC 2445, November 1998.

   5.  J. Boyle, R. Cohen, D. Durham, S. Herzog, R. Rajan, A. Sastry,
   "The COPS (Common Open Policy Service) Protocol" RFC 2748, January
   2000.

   6.  K. Chan, D. Durham, S. Gai, S. Herzog, K. McCloghrie, F.
   Reichmeyer, J. Seligson, A. Smith, R. Yavatkar, "COPS Usage for
   Policy Provisioning," RFC 3084, March 2001.

   7.  D. Piper, "The Internet IP Security Domain of Interpretation
   for ISAKMP", RFC 2407, November 1998.

   8.  S. Kent, R. Atkinson, "IP Encapsulating Security Payload
   (ESP)", RFC 2406, November 1998.

   9.  M. Fine, K. McCloghrie, J. Seligson, K. Chan, S. Hahn, A.
   Smith, F. Reichmeyer "Framework Policy Information Base", draft-
   ietf-rap-frameworkpib-06.txt, November 2001.

   10.  D. Harkins, D. Carrel, "The Internet Key Exchange (IKE)", RFC
   2409, November 1998.

   11.  A. Shacham, R. Monsour, R. Pereira, M. Thomas, "IP Payload
   Compression Protocol (IPComp)", RFC 2393, August 1998.


   Li, et al            Expires August, 2002                       89
                    IPsec Policy Information Base      February, 2002


   12.  J. Jason, L. Rafalow, E. Vyncke  ôIPsec Configuration Policy
   Model,ö draft-ietf-ipsp-config-policy-model-04.txt, November 2001.

   13.  B. Moore, E. Ellesson, J. Strassner, ôPolicy Core Information
   Model -- Version 1 Specificationö, RFC 3060, February 2000.

   14.  K. McCloghrie, M. Fine, J. Seligson, K. Chan, S. Chan, A.
   Smith, F. Reichmeyer, "Structure of Policy Provisioning
   Information," RFC 3159, August 2001.


8. Author's Addresses

   Man Li
   Nokia
   5 Wayside Road,
   Burlington, MA 01803
   Phone: +1 781 993 3923
   Email: man.m.li@nokia.com

   David Arneson
   Email: dla@mediaone.net

   Avri Doria
   Div. of Computer Communications
   Lulea University of Technology
   SE-971 87
   Lulea, Sweden
   Phone: +46 920 49 3030
   Email: avri@sm.luth.se

   Jamie Jason
   Intel Corporation
   MS JF3-206
   2111 NE 25th Ave.
   Hillsboro, OR 97124
   Phone: +1 503 264 9531
   Email: jamie.jason@intel.com

   Cliff Wang
   SmartPipes Inc.
   Suite 300, 565 Metro Place South
   Dublin, OH 43017
   Phone: +1 614 923 6241
   Email: CWang@smartpipes.com

   Markus Stenberg
   SSH Communications Security Corp.
   Fredrikinkatu 42
   FIN-00100 Helsinki, Finland
   Phone: +358 20 500 7466
   Email: markus.stenberg@ssh.com


   Li, et al            Expires August, 2002                       90
                    IPsec Policy Information Base      February, 2002



   Full Copyright Statement

   "Copyright (C) The Internet Society (date). All Rights Reserved.
   This document and translations of it may be copied and furnished
   to others, and derivative works that comment on or otherwise
   explain it or assist in its implementation may be prepared,
   copied, published and distributed, in whole or in part, without
   restriction of any kind, provided that the above copyright notice
   and this paragraph are included on all such copies and derivative
   works. However, this document itself may not be modified in any
   way, such as by removing the copyright notice or references to the
   Internet Society or other Internet organizations, except as needed
   for the purpose of developing Internet standards in which case the
   procedures for copyrights defined in the Internet Standards
   process must be followed, or as required to translate it into.

Table of Contents

1. Introduction                                                      2
2. Operation Overview                                                2
3. Structure of IPsec PIB                                            3
3.1 IPsec association group                                          3
3.2 AH, ESP and COMP transform groups                                5
3.3 IKE association group                                            5
3.4 Credential group                                                 6
3.5 Selector group                                                   6
3.6 Policy time period group                                         7
3.7 Interface capability group                                       7
4. Summary of the IPsec PIB                                          8
4.1 ipSecAssociation group                                           8
4.1.1 ipSecRuleTable                                                 8
4.1.2 ipSecActionSetTable                                            8
4.1.3 ipSecStaticActionTable                                         8
4.1.4 ipSecNegotiationActionTable                                    8
4.1.5 ipSecAssociationTable                                          8
4.1.6 ipSecProposalSetTable                                          8
4.1.7 ipSecProposalTable                                             8
4.2 ipSecAhTransform group                                           8
4.2.1 ipSecAhTransformSetTable                                       8
4.2.2 ipSecAhTransformTable                                          8
4.3 ipSecEspTransform group                                          8
4.3.1 ipSecEspTransformSetTable                                      8
4.3.2 ipSecEspTransformTable                                         8
4.4 ipSecCompTransform group                                         9
4.4.1 ipSecCompTransformSetTable                                     9
4.4.2 ipSecCompTransformTable                                        9
4.5 ipSecIkeAssociation group                                        9
4.5.1 ipSecIkeRuleTable                                              9
4.5.2 ipSecIkeActionSetTable                                         9
4.5.3 ipSecIkeAssociationTable                                       9
4.5.4 ipSecIkeProposalSetTable                                       9
4.5.5 ipSecIkeProposalTable                                          9

   Li, et al            Expires August, 2002                       91
                    IPsec Policy Information Base      February, 2002


4.5.6 ipSecIkePeerEndpointTable                                      9
4.6 ipSecCredential group                                            9
4.6.1 ipSecCredentialSetTable                                        9
4.6.2 ipSecCredentialTable                                           9
4.6.3 ipSecCredentialFieldsTable                                     9
4.7 ipSecSelector group                                              9
4.7.1 ipSecSelectorSetTable                                          9
4.7.2 ipSecSelectorTable                                             9
4.7.3 ipSecAddressTable                                              10
4.7.4 ipSecL4PortTable                                               10
4.7.5 ipSecIpsoFilterSetTable                                        10
4.7.6 ipSecIpsoFilterTable                                           10
4.8 ipSecPolicyTimePeriod group                                      10
4.8.1 ipSecRuleTimePeriodTable                                       10
4.8.2 ipSecRuleTimePeriodSetTable                                    10
4.9 ipSecIfCapability group                                          10
4.9.1 ipSecIfCapsTable                                               10
4.10 ipSecPolicyPibConformance group                                 10
5. The IPsec PIB Module                                              10
6. Security Considerations                                           89
7. References                                                        89
8. Author's Addresses                                                90
































   Li, et al            Expires August, 2002                       92


Html markup produced by rfcmarkup 1.129b, available from https://tools.ietf.org/tools/rfcmarkup/