[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits] [IPR]

Versions: 00 01 02 03 04 05 06 07 08 09 10 11 12 RFC 4541

Network Working Group                                     M. Christensen
Internet Draft                                           Thrane & Thrane
Expiration Date: October 2003                                 K. Kimball
Category: Informational                                  Hewlett-Packard
                                                             F. Solensky
                                                                May 2003

           Considerations for IGMP and MLD Snooping Switches

Status of this Memo

     This document is an Internet-Draft and is in full conformance with
     all provisions of Section 10 of RFC2026 [RFC2026].

     Internet-Drafts are working documents of the Internet Engineering
     Task Force (IETF), its areas, and its working groups.  Note that
     other groups may also distribute working documents as Internet-

     Internet-Drafts are draft documents valid for a maximum of six
     months and may be updated, replaced, or obsoleted by other
     documents at any time.  It is inappropriate to use Internet-Drafts
     as reference material or to cite them other than as "work in

     The list of current Internet-Drafts can be accessed at

     The list of Internet-Draft Shadow Directories can be accessed at

Copyright Notice

     Copyright (C) The Internet Society (2003).  All Rights Reserved.


     This memo describes the requirements for IGMP- and MLD-snooping
     switches. These are based on best current practices for IGMPv2,
     with further considerations for IGMPv3- and MLDv2-snooping.
     Additional areas of relevance, such as link layer topology changes
     and Ethernet-specific encapsulation issues, are also considered.

     Interoperability issues that arise between different versions of

Christensen, Kimball, Solensky                                  [Page 1]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

     IGMP are not the focus of this document.  Interested readers are
     directed to [IGMPv3] for a thorough description of problem areas.

1.  Introduction

     When processing a packet whose destination MAC address is a
     multicast address, the switch will forward a copy of the packet
     into each of the remaining network interfaces that are the
     forwarding state in accordance with [BRIDGE].  The spanning tree
     algorithm ensures that the application of this rule at every switch
     in the network will make the packet accessible to all nodes
     connected to the network.

     This approach works well for broadcast packets that are intended to
     be seen or processed by all connected nodes.  In the case of
     multicast packets, however, this approach could lead to less
     efficient use of network bandwidth, particularly when the packet is
     intended for only a small number of nodes.  Packets will be flooded
     into network segments where no node has any interest in receiving
     the packet.  While nodes will rarely incur any processing overhead
     to filter packets addressed to unrequested group addresses, they
     are unable to transmit new packets onto the shared media for the
     period of time that the multicast packet is flooded.  In general,
     significant bandwidth can be wasted by flooding.

     In recent years, a number of commercial vendors have introduced
     products described as "IGMP snooping switches" to the market.
     These devices do not adhere to the conceptual model that provides
     the strict separation of functionality between different
     communications layers in the ISO model, and instead utilize
     information in the upper level protocol headers as factors to be
     considered in the processing at the lower levels.  This is
     analogous to the manner in which a router can act as a firewall by
     looking into the transport protocol's header before allowing a
     packet to be forwarded to its destination address.

     In the case of multicast traffic, an IGMP snooping switch provides
     the benefit of conserving bandwidth on those segments of the
     network where no node has expressed interest in receiving packets
     addressed to the group address.  This is in contrast to normal
     switch behavior where multicast traffic is typically forwarded on
     all interfaces.

     Many switch datasheets state support for IGMP snooping, but no
     requirements for this exist today.  It is the authors' hope that
     the information presented in this draft will supply this

Christensen, Kimball, Solensky                                  [Page 2]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

     The requirements presented here are based on the following
     information sources: The IGMP specifications [RFC1112], [RFC2236]
     and [IGMPv3], vendor-supplied technical documents [CISCO], bug
     reports [MSOFT], discussions with people involved in the design of
     IGMP snooping switches, MAGMA mailing list discussions, and on
     replies by switch vendors to an implementation questionnaire.

     The suggestions in this document are based on IGMP, which applies
     only to IPv4.  For IPv6, Multicast Listener Discovery [MLD] must be
     used instead.  Because MLD is based on IGMP, we do not repeat the
     entire description and requirements for MLD snooping switches.
     Instead, we point out the few cases where there are differences
     from IGMP.

     Note that the IGMP snooping function should apply only to IPv4
     multicasts.  Other multicast packets, such as IPv6, might be
     suppressed by IGMP snooping if additional care is not taken in the
     implementation.  It is desired not to restrict the flow of non-IPv4
     multicasts other than to the degree which would happen as a result
     of regular bridging functions.  Likewise, MLD snooping switches are
     discouraged from using topological information learned from IPv6
     traffic to alter the forwarding of IPv4 multicast packets.

2.  IGMP Snooping Requirements

     The following sections list the requirements for an IGMP snooping
     switch.  The requirement is stated and is supplemented by a
     description of a possible implementation approach.  All
     implementation discussions are examples only and there may well be
     other ways to achieve the same functionality.

2.1.  Forwarding rules

     The IGMP snooping functionality is here separated into a control
     section (IGMP forwarding) and a data section (Data forwarding).

2.1.1.  IGMP Forwarding Rules

     1)  A snooping switch should forward IGMP Membership Reports only
         to those ports where multicast routers are attached.
         Alternatively stated: a snooping switch should not forward IGMP
         Membership Reports to ports on which only hosts are attached.
         An administrative control may be provided to override this
         restriction, allowing the report messages to be flooded to
         other ports.

Christensen, Kimball, Solensky                                  [Page 3]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

         This is the main IGMP snooping functionality.  Sending
         membership reports (as described in IGMP versions 1 and 2) to
         other hosts can result in unintentionally preventing a host
         from joining a specific multicast group.  This is not a problem
         in an IGMPv3-only network because there is no message
         suppression of IGMP Membership reports.

         The administrative control allows IGMP Membership Report
         messages to be processed by network monitoring equipment such
         as packet analyzers or port replicators.

         The switch supporting IGMP snooping must maintain a list of
         multicast routers and the ports on which they are attached.
         This list can be constructed in any combination of the
         following ways:

         a)  This list should be built by the snooping switch sending
             Multicast Router Solicitation messages as described in IGMP
             Multicast Router Discovery [MRDISC].  It may also snoop
             Multicast Router Advertisement messages sent by and to
             other nodes.

         b)  The arrival port for IGMP Queries (sent by multicast
             routers) where the source address is not

         c)  Ports explicitly configured by management to be IGMP-
             forwarding ports, in addition to or instead of any of the
             above methods to detect router ports.

     2)  IGMP snooping switches may also implement "proxy-reporting" in
         which reports received from downstream hosts are summarized and
         used to build internal membership states as described in
         [PROXY].  The IGMP proxy-reporting switch would then report its
         own state in response to upstream queriers.  If the switch does
         not already have an IP address assigned to it, the source
         address for these reports should be set to all-zeros.

         An IGMP proxy-reporting switch may act as Querier for the
         downstream hosts while proxy reporting to the 'real' upstream

         It should be noted that there may be multiple IGMP proxy-
         reporting switches in the network all using the source
         IP address.  In this case the switches can be uniquely
         identified through their link layer source MAC address.

         IGMP membership reports must not be rejected by an IGMP
         snooping switch because of a source IP address of

Christensen, Kimball, Solensky                                  [Page 4]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

     3)  The switch that supports IGMP snooping must flood all
         unrecognized IGMP messages to all other ports and must not
         attempt to make use of any information beyond the end of the
         network layer header.

         In addition, earlier versions of IGMP should interpret IGMP
         fields as defined for their versions and must not alter these
         fields when forwarding the message.  When generating new
         messages, a given IGMP version should set fields to the
         appropriate values for its own version.  If any fields are
         reserved or otherwise undefined for a given IGMP version, the
         fields should be ignored when parsing the message and must be
         set to zeroes when new messages are generated by
         implementations of that IGMP version.  An exception may occur
         if the switch is performing a spoofing function, and is aware
         of the settings for new or reserved fields that would be
         required to correctly spoof for a different IGMP version.

     4)  An IGMP snooping switch should be aware of link layer topology
         changes caused by Spanning Tree operation. When a port is
         enabled or disabled by Spanning Tree, a General Query may be
         sent on all active non-router ports in order to reduce network
         convergence time.  Non-Querier switches should be aware of
         whether the Querier is in IGMPv3 mode. If so, the switch should
         not spoof any General Queries unless it is able to send an
         IGMPv3 Query that adheres to the most recent information sent
         by the true Querier. In no case should a switch introduce a
         spoofed IGMPv2 Query into an IGMPv3 network, as this may create
         excessive network disruption.

         If the switch is not the Querier, it should use the 'all-zeros'
         IP Source Address in these proxy queries (even though some
         hosts may elect to not process queries with a IP Source
         Address).  When such proxy queries are received, they must not
         be included in the Querier election process.

     5)  An IGMP snooping switch must not make use of information in
         IGMP packets where the IP or IGMP headers have checksum or
         integrity errors.  The switch should not flood such packets but
         if it does, it should also take some note of the event (i.e.,
         increment a counter).  These errors and their processing are
         further discussed in [IGMPv3], [MLD] and [MLDv2].

     6)  The snooping switch must not rely exclusively on the appearance
         of IGMP Group Leave announcements to determine when entries
         should be removed from the forwarding table.  It should
         implement a membership timeout mechanism such as the router-
         side functionality of the IGMP protocol as described in

Christensen, Kimball, Solensky                                  [Page 5]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

         [IGMPv3] on all its non-router ports.  This timeout value
         should be configurable.

2.1.2.  Data Forwarding Rules

     1)  Packets with a destination IP (DIP) address in the 224.0.0.X
         range which are not IGMP must be forwarded on all ports.

         This requirement is based on fact that many host systems do not
         send Join IP multicast addresses in this range before sending
         or listening to IP multicast packets.  Furthermore, since the
         224.0.0.X address range is defined as link-local (not to be
         routed) it seems unnecessary to keep state for each address in
         this range.  Additionally, some routers operate in the
         224.0.0.X address range without issuing IGMP Joins, and these
         applications would break if the switch were to prune them due
         to not having seen a Join Group message from the router.

     2)  Packets with a destination IP address outside 224.0.0.X which
         are not IGMP should be forwarded according to group-based port
         membership tables and must also be forwarded on router ports.
         This is the core IGMP snooping requirement for the data path.
         One approach that an implementation could take would be to
         maintain separate membership and multicast router tables in
         software and then "merge" these tables into a forwarding cache.

     3)  If a switch receives a non-IGMP IPv4 multicast packet without
         having first processed Membership Reports for the group
         address, it may forward the packet on all ports but it must
         forward the packet on router ports.  A switch may forward an
         unregistered packet only on router ports, but the switch must
         have a configuration option that suppresses this restrictive
         operation and forces flooding of unregistered packets on
         selected ports.

         In an environment where IGMPv3 hosts are mixed with snooping
         switches that do not yet support IGMPv3, the switch's failure
         to flood unregistered streams could prevent v3 hosts from
         receiving their traffic.  Alternatively, in environments where
         the snooping switch supports all of the IGMP versions that are
         present, flooding unregistered streams may cause IGMP hosts to
         be overwhelmed by multicast traffic, even to the point of not
         receiving Queries and failing to issue new membership reports
         for their own groups.

         It is encouraged that snooping switches at least recognize and
         process IGMPv3 Join Reports, even if this processing is limited

Christensen, Kimball, Solensky                                  [Page 6]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

         to the behavior for IGMPv2 Joins, i.e., is done without
         considering any additional "include source" or "exclude source"
         filtering. When IGMPv3 Joins are not recognized, a snooping
         switch may incorrectly prune off the unregistered data streams
         for the groups (as noted above); alternatively, it may fail to
         add in forwarding to any new IGMPv3 hosts if the group has
         previously been joined as IGMPv2 (because the data stream is
         seen as already having been registered).

     4)  All non-IPv4 multicast packets should continue to be flooded
         out all remaining ports in the forwarding state as per normal
         IEEE bridging operations.

         This requirement is a result of the fact that groups made up of
         IPv4 hosts and IPv6 hosts are completely separate and distinct
         groups.  As a result, information gleaned from the topology
         between members of an IPv4 group would not be applicable when
         forming the topology between members of an IPv6 group.

     5)  IGMP snooping switches may maintain forwarding tables based on
         either MAC addresses or IP addresses.  If a switch supports
         both types of forwarding tables then the default behavior
         should be to use IP addresses.  IP address based forwarding is
         preferred because the mapping between IP multicast addresses
         and link-layer multicast addresses is ambiguous.  In the case
         of Ethernet, there is a multiplicity of 1 Ethernet address to
         32 IP addresses [RFC1112].

     6)  Switches which rely on information in the IP header should
         verify that the IP header checksum is correct.  If the checksum
         fails, the information in the packet must not be incorporated
         into the forwarding table.  Further, the packet should be

     7)  When IGMPv3 "include source" and "exclude source" membership
         reports are received on shared segments, the switch needs to
         forward the superset of all received membership reports onto
         the shared segment.  Forwarding of traffic from a particular
         source S to a group G must happen if at least one host on the
         shared segment reports an IGMPv3 membership of the type
         INCLUDE(G, Slist1) or EXCLUDE(G, Slist2) where S is an element
         of Slist1 and not an element of Slist2.

2.2.  IGMP snooping-related problems

     A special problem arises in networks consisting of IGMPv3 routers
     as well as IGMPv2 and IGMPv3 hosts interconnected by an IGMPv2

Christensen, Kimball, Solensky                                  [Page 7]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

     snooping switch as recently reported [IETF56].  The router will
     continue to maintain IGMPv3 even in the presence of IGMPv2 hosts,
     and thus the network will not converge on IGMPv2.  But it is likely
     that the IGMPv2 snooping switch will not recognize or process the
     IGMPv3 membership reports.  Groups for these unrecognized reports
     will then either be flooded (with all of the problems that may
     create for hosts in a network with a heavy multicast load) or
     pruned by the snooping switch.

     Therefore, it is recommended that in such a network, the multicast
     router be configured to use IGMPv2. If this is not possible, and if
     the snooping switch cannot recognize and process the IGMPv3
     membership reports, it is instead recommended that the switch's
     IGMP snooping functionality be disabled, as there is no clear
     solution to this problem.

3.  IPv6 Considerations

     In order to avoid confusion, the previous discussions have been
     based on the IGMP protocol which only applies to IPv4 multicast.
     In the case of IPv6 most of the above discussions are still valid
     with a few exceptions which we will describe here.

     The control and data forwarding rules in the IGMP section can, with
     a few considerations, also be applied to MLD.  This means that the
     basic functionality of intercepting MLD packets, and building
     membership lists and multicast router lists, is the same as for

     In IPv6, the data forwarding rules are more straight forward
     because MLD is mandated for addresses with scope 2 (link-scope) or
     greater.  The only exception is the address FF02::1 which is the
     all hosts link-scope address for which MLD messages are never sent.
     Packets with the all hosts link-scope address should be forwarded
     on all ports.

     MLD messages are also not sent to packets in the address range
     FF00::/15 (which encompasses both the reserved FF00::/16 and node-
     local FF01::/16 IPv6 address spaces).  These addresses should never
     appear in packets on the link.

     Equivalent to the IPv4 behaviors regarding the null IP Source
     address, MLD membership reports must not be rejected by an MLD
     snooping switch because of an unspecified IP source address (::).
     Additionally, if a non-Querier switch spoofs any General Queries
     (as addressed in Section 2.1 above, for Spanning Tree topology
     changes), the switch should use the null IP source address (::)

Christensen, Kimball, Solensky                                  [Page 8]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

     when sending said queries.  When such proxy queries are received,
     they must not be included in the Querier election process.

     The three major differences between IPv4 and IPv6 in relation to
     multicast are:

     -  The IPv6 protocol for multicast group maintenance is called
        Multicast Listener Discovery [MLDv2].  MLDv2 uses ICMPv6 message
        types instead of IGMP message types.

     -  The RFCs [IPV6-ETHER] and [IPV6-FDDI] describe how 24 of the 128
        bit DIP address are used to form the 48 bit DMAC addresses for
        multicast groups, while [IPV6-TOKEN] describes the mapping for
        token ring DMAC addresses by using three low-order bits.  The
        specification [IPV6-1394] makes use of a 6 bit channel number.

     -  Multicast router discovery is accomplished using Neighbor
        Discovery Protocol [NDP] for IPv6.  NDP uses ICMPv6 message

     The IPv6 packet header does not include a checksum field.
     Nevertheless, the switch should detect other packet integrity
     issues.  When the snooping switch detects such an error, it must
     not include information from the corresponding packet in the MLD
     forwarding table.  The forwarding code should instead drop the
     packet and take further reasonable actions as advocated above.

     The fact that MLDv2 is using ICMPv6 adds new requirements to a
     snooping switch because ICMPv6 has multiple uses aside from MLD.
     This means that it is no longer sufficient to detect that the next-
     header field of the IP header is ICMPv6 in order to identify
     packets relevant for MLD snooping.  A software-based implemention
     which treats all ICMPv6 packets as candidates for MLD snooping
     could easily fill its receive queue and bog down the CPU with
     irrelevant packets.  This would prevent the snooping functionality
     from performing its intended purpose and the non-MLD packets
     destined for other hosts could be lost.

     A solution is either to require that the snooping switch looks
     further into the packets, or to be able to detect a multicast DMAC
     address in conjunction with ICMPv6.  The first solution is
     desirable when a configuration option allows the administrator to
     specify which ICMPv6 message types should trigger a CPU redirect
     and which should not.  The reason is that a hardcoding of message
     types is inflexible for the introduction of new message types.  The
     second solution introduces the risk that new protocols which use
     ICMPv6 and multicast DMAC addresses could be incorrectly identified
     as MLD.  It is suggested that solution one is preferred when the

Christensen, Kimball, Solensky                                  [Page 9]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

     administrative switch is provided.  If this is not the case, then
     the implementator should seriously consider making this switch
     available since Neighbor Discovery messages would be among those
     that fall into this false positive case and are vital for the
     operational integrity of IPv6 networks.

     The mapping from IP multicast addresses to multicast DMAC addresses
     introduces a potentially enormous overlap.  The structure of an
     IPv6 multicast address is shown in the figure below.  As a result,
     there are 2 ** (112 - (32 - 8)), or more than 7.9e28 unique DIP
     addresses which map into a single DMAC address in Ethernet and
     FDDI.  This should be compared to 2**5 in the case of IPv4.

     Initial allocation of IPv6 multicast addresses as described in
     [RFC2735], however, cover only the lower 24 bits of group ID.
     While this reduces the problem of address ambiguity to group IDs
     with different flag and scope values for now, it should be noted
     that the allocation policy may change in the future.  Because of
     the potential overlap it is recommended that IPv6 address based
     forwarding is preferred to MAC address based forwarding.

        |   8    |  4 |  4 |             112 bits                  |
        |11111111|flgs|scop|             group ID                  |

4.  IGMP Questionnaire

     As part of this work the following questions were asked both on the
     MAGMA discussion list and sent to known switch vendors implementing
     IGMP snooping.  The individual contributions have been anonymized
     upon request and do not necessarily apply to all of the vendors'

     The questions were:

     Q1  Does your switches perform IGMP Join aggregation?  In other
         words, are IGMP joins intercepted, absorbed by the
         hardware/software so that only one Join is forwarded to the

     Q2  Is multicast forwarding based on MAC addresses?  Would
         datagrams addressed to multicast IP addresses and be forwarded on the same ports-groups?

     Q3  Is it possible to forward multicast datagrams based on IP
         addresses (not routed)? In other words, could and

Christensen, Kimball, Solensky                                 [Page 10]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

 be forwarded on different port-groups with
         unaltered TTL?

     Q4  Are multicast datagrams within the range to forwarded on all ports whether or not IGMP Joins
         have been sent?

     Q5  Are multicast frames within the MAC address range
         01:00:5E:00:00:01 to 01:00:5E:00:00:FF forwarded on all ports
         whether or not IGMP joins have been sent?

     Q6  Does your switch support forwarding to ports on which IP
         multicast routers are attached in addition to the ports where
         IGMP Joins have been received?

     Q7  Is your IGMP snooping functionality fully implemented in

     Q8  Is your IGMP snooping functionality partly software

     Q9  Can topology changes (for example spanning tree configuration
         changes) be detected by the IGMP snooping functionality so that
         for example new queries can be sent or tables can be updated to
         ensure robustness?

Christensen, Kimball, Solensky                                 [Page 11]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

     The answers were:

                                     |     Switch Vendor     |
                                     | 1 | 2 | 3 | 4 | 5 | 6 |
          Q1 Join aggregation        | x | x | x |   | x | x |
          Q2 Layer-2 forwarding      | x | x | x | x |(1)|   |
          Q3 Layer-3 forwarding      |(1)|   |(1)|   |(1)| x |
          Q4 224.0.0.X aware         |(1)| x |(1)|(2)| x | x |
          Q5 01:00:5e:00:00:XX aware | x | x | x |(2)| x | x |
          Q6 Mcast router list       | x | x | x | x | x | x |
          Q7 Hardware implemented    |   |   |   |   |   |   |
          Q8 Software assisted       | x | x | x | x | x | x |
          Q9 Topology change aware   | x | x | x | x |   |(2)|
                    x  Means that the answer was Yes.
      (1) In some products (typically high-end) Yes; in others No.
        (2) Not at the time that the questionnaire was received
                      but expected in the near future.

Revision History

     This section, while incomplete, is provided as a convenience to the
     working group members.  It will be removed when the document is
     released in its final form.

     draft-ietf-magma-snoop-07.txt: May 2003

          The current version reflects comments made at the 56'th IETF
          meeting and from the previous WG last call. The majority of
          changes appear in sections 2.1 and 2.2, and even the changes
          here are in reality not substantial.

          Substantial comments

               Section 2.1.1.(4): Changed wording for IGMP forwarding
               section on when spoofing of General Queries should occur.
               Added description of how to avoid IGMP version
               incompatibility problems when doing said spoofing.

               Section 2.1.2.(3): Clarification of incompatibility
               problems in mixed IGMPv2 and IGMPv3 networks. Added
               recommendation for switches to implement some level of

Christensen, Kimball, Solensky                                 [Page 12]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

               IGMPv3 Join recognition to reduce these problems.

               Section 2.2: Advice following the briefing [IETF56], that
               in some cases disabling IGMP snooping functionality is
               the only 'solution'

               Section 6, IPv6 Considerations: added descriptions of
               behavior involving the IPv6 version of the null IP Source
               Address (to parallel the IPv4 behaviors).

               Added reference to [IGMPv3] in stead of [PROXY] for group
               membership maintenance and timeout.

          Editorial Changes

               Really minor stuff such as change of authors email
               address, addition of references, draft name increment and
               date changes.

     draft-ietf-magma-snoop-06.txt: March 2003

          Changes in response to comments made during WG last call and
          assessment by the WG chairs:

          Substantial comments

               Clarification in IGMP forwarding section on the
               acceptance of membership reports with source IP address
      as being a switch requirement.

               Section 2.1.1.(4): Allow the router port to be excluded
               from the General Query messages

               Section 2.1.1.(6): Replace description of timing out
               older entries with a reference to IGMP/MLD Proxying.

               Section 2.1.2.(3): Replaced description of timeout
               mechanism with a reference to IGMP/MLD.

               Section 2.1.2.(4)  Expanded rationale to discourage
               leaking info between IPv4 and IPv6 groups.

               Section 3: more strongly encourage the use of a
               configuration option for selection of ICMPv6 message

          Editorial comments.

Christensen, Kimball, Solensky                                 [Page 13]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

               Hyphenation problem resolved for groff by setting then ms
               HY register to zero, disabling all forms for the entire
                (".hy 0" and ".nr" worked only as far as the following
               ms macro).

               Sections moved around - again - to comply with
               rfc2223bis-03 draft. Added copyright notice after memo
               status. Removed table of contents as the draft is fairly
               short. Corrected  a reference typo.

               Section 2.1.2.(3): Requirement and rationale broken into
               separate paragraphs.

               Added references to other IPv6 encapsulation documents,

               Corrected estimates for MAC address collisions for
               Ethernet and FDDI: both specification take the low-order
               four (not six) bytes from the IPv6 group addresses.

     draft-ietf-magma-snoop-05.txt: January 2003

          Changes in wording of IGMP forwarding rule 6) and Data
          forwarding rule 7).  Corrections in the references section.

          Apart from above, no substantial changes has occured in the
          document.  Several editorial changes, however, have been made
          to comply with the rfc editors requirements:

          References splitted in normative and informative sections,
          other related references added.

          Abstract shortened.

          Changed all occurances of MUST, MAY etc. to lowercase to
          reflect that this is not a standards track document.

          Sections moved around so they appear in the required order.

     draft-ietf-magma-snoop-04.txt: November 2002

          Editorial changes only.

     draft-ietf-magma-snoop-03.txt: October 2002

          IGMP Forwarding rules:
               Add references to and become consistant with the current
               IGMP proxy draft,

Christensen, Kimball, Solensky                                 [Page 14]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

               Unrecognized IGMP packets should not be ignored because
               "mbz" fields are not zero since packets from future
               versions are expected to maintain consistency.

               Corrections related to IGMP Querier election process.

               Add clarification to how lists of router ports may be

          Data Forwarding rules:
               Added discussion of the problems for different IGMP
               environments in choosing whether to flood or to prune
               unregistered multicasts.

               Added refinements for how to handle NON-IPv4 multicasts,
               to keep IGMP-snooping functionality from interfering with
               IPv6 and other multicast traffic.  Any filtering for non-
               IPv4 multicasts should be based on bridge behavior and
               not IGMP snooping behavior.

          IGMP snooping related problems:
               Fixed description of interoperability issues in
               environments with v3 routers and hosts, and v2 snooping

               Added discussion of the IGMPv3 "include source" and
               "exclude source" options, and the inability to support
               them on shared segments.

          IPv6 Considerations:
               Clarifications regarding address ranges FF00::, FF01::
               and all hosts FF02::1 in relation to data forwarding.

     draft-ietf-magma-snoop-02.txt: June 2002

          Status section removes document history; moved into this
          section instead.

          Introduction restores text from the -00 revision that
          describes snooping and its goals

          IGMP flooding rules eased, allowing management option to
          broaden beyond "routers only".

          Removed a should/MAY inconsistancy between IPv4 Forwarding and
          IPv6 processing of checksums.

Christensen, Kimball, Solensky                                 [Page 15]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

          IGMP Forwarding Rules: clarify text describing processing of
          non-zero reserved fields.

          Data Forwarding Rules, item 3 is changed from "MUST forward to
          all ports" to "MAY"; item 4 default changes from "MUST" to
          "should use network addresses".

          Added two sets of additional responses to the questionnaire
          and text indicating that responses don't cover all products.

          Removed (commented out) description of IPR issues: IESG is
          aware of them.

     draft-ietf-magma-snoop-01.txt: January 2002

          Extensive restructuring of the original text.

     draft-ietf-idmr-snoop-01.txt:  2001

          Added several descriptions of cases where IGMP snooping
          implementations face problems.  Also added several network
          topology figures.

     draft-ietf-idmr-snoop-00.txt: 2001

          Initial snooping draft.  An overview of IGMP snooping and the
          problems to be solved.

     5.  References

     5.1.  Normative References

          [BRIDGE]     IEEE 802.1D, "Media Access Control (MAC) Bridges"

          [IGMPv3]     Cain, B., "Internet Group Management Protocol,
                       Version 3", RFC3376, October 2002.

          [IPV6-1394]  Fujisawa, K. and Onoe, A., "Transmission of IPv6
                       Packets over IEEE 1394 Networks", RFC3146,
                       October 2001.

          [IPV6-ETHER] Crawford, M., "Transmission of IPv6 Packets over
                       Ethernet Networks", RFC2464, December 1998.

Christensen, Kimball, Solensky                                 [Page 16]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

          [IPV6-FDDI]  Crawford, M., "Transmission of IPv6 Packets over
                       FDDI Networks", RFC2467, December 1998.

          [IPV6-TOKEN] Crawford, M., Narten, T. and Thomas, S.,
                       "Transmission of IPv6 Packets over Token Ring
                       Networks", RFC2470, December 1998.

          [MLD]        Deering, S., Fenner, B. and Haberman, B.
                       "Multicast Listener Discovery (MLD) for IPv6",
                       RFC2710, October 1999.

          [MLDv2]      Vida, R. and Costa, L., "Multicast Listener
                       Discovery Version 2 (MLDv2) for IPv6", draft-
                       vida-mld-v2-06.txt, November 2002.

          [MRDISC]     Biswas, S., Cain, B. and Haberman, B., "Multicast
                       Router Discovery", draft-ietf-idmr-igmp-
                       mrdisc-10.txt, January 2003.

          [NDP]        Narten, T., Nordmark, E. and Simpson, W.,
                       "Neighbor Discovery for IP Version 6 {IPv6)",
                       RFC2461, December 1998.

          [PROXY]      Fenner, B.  et al, "IGMP/MLD-based Multicast
                       Forwarding (IGMP/MLD Proxying)", draft-ietf-
                       magma-igmp-proxy-02.txt, November 2002.

          [RFC1112]    Deering, S., "Host Extensions for IP
                       Multicasting", RFC1112, August 1989.

          [RFC2026]    Bradner, S.  "The Internet Standards Process --
                       Revision 3", RFC2026, October 1996.

          [RFC2236]    Fenner, W., "Internet Group Management Protocol,
                       Version 2", RFC2236, November 1997.

          [RFC2375]    Hinden, R.  "IPv6 Multicast Address Assignments",
                       RFC2375, July 1998.

     5.2.  Informative References

          [IANA]       Internet Assigned Numbers Authority, "Internet
                       Multicast Addresses", http://www.isi.edu/in-

Christensen, Kimball, Solensky                                 [Page 17]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

          [CISCO]      Cisco Tech Notes, "Multicast In a Campus Network:
                       CGMP and IGMP snooping",

          [MSOFT]      Microsoft support article Q223136, "Some LAN
                       Switches with IGMP Snooping Stop Forwarding
                       Multicast Packets on RRAS Startup",

          [IETF56]     Briefing by Dave Thaler, Microsoft, presented to
                       the MAGMA WG at the 56'th IETF meeting in San

     6.  Security Considerations

          Security considerations for IGMPv3 are accounted for in
          [IGMPv3].  The introduction of IGMP snooping switches adds the
          following considerations with regard to IP multicast.

          -   The exclude source failure, which could cause traffic from
              sources that are 'black listed' to reach hosts that have
              requested otherwise.  This can also occur in certain
              network topologies without IGMP snooping.

          -   It is possible to generate packets which make the switch
              wrongly believe that there is a multicast router on the
              segment on which the source is attached.  This will
              potentially lead to excessive flooding on that segment.
              The authentication methods discussed in [IGMPv3] will also
              provide protection in this case.

          -   IGMP snooping switches which rely on the IP header of a
              packet for their operation and which do not validate the
              header checksum potentially will forward packets on the
              wrong ports.  Even though the IP headers are protected by
              the Ethernet checksum this is a potential vulnerability.

          -   In IGMP, there is no mechanism for denying recipients
              access to groups (i.e. no "exclude receiver"
              functionality).  Hence, apart from IP-level security
              configuration outside the scope of IGMP, any multicast
              stream may be received by any host without restriction.

          Generally, IGMP snooping must be considered insecure due to
          the issues above. However, none of the these issues are any
          worse for IGMP snooping than for IGMP implementations in

Christensen, Kimball, Solensky                                 [Page 18]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003


     7.  Acknowledgements

          We would like to thank Martin Bak, Les Bell, Yiqun Cai, Ben
          Carter, Paul Congdon, Toerless Eckert, Bill Fenner, Brian
          Haberman, Edward Hilquist, Hugh Holbrook, Kevin Humphries,
          Pekka Savola, Suzuki Shinsuke, Jaff Thomas, and Rolland Vida
          for comments and suggestions on this document.

          Furthermore, the following companies are acknowledged for
          their contributions: 3Com, Alcatel, Cisco Systems, Enterasys
          Networks, Hewlett-Packard, Vitesse Semiconductor Corporation.
          The ordering of these names do not necessarily correspond to
          the column numbers in the response table.

     8.  Authors' Addresses

          Morten Jagd Christensen
          Thrane & Thrane
          Lundtoftegaardsvej 93 D
          2800 Lyngby
          email: mjc@tt.dk

          Karen Kimball
          8000 Foothills Blvd.
          Roseville, CA 95747
          email: karen.kimball@hp.com

          Frank Solensky
          Bluejavelin, Inc.
          3 Dundee Park
          Andover, MA 01810
          email: solenskyf@acm.org

     9.  IETF IPR Statement

          "The IETF takes no position regarding the validity or scope of
          any intellectual property or other rights that might be
          claimed to  pertain to the implementation or use of the
          technology described in this document or the extent to which
          any license under such rights might or might not be available;
          neither does it represent that it has made any effort to
          identify any such rights.  Information on the IETF's

Christensen, Kimball, Solensky                                 [Page 19]

RFC DRAFT            IGMP and MLD Snooping Switches           April 2003

          procedures with respect to rights in standards-track and
          standards-related documentation can be found in [RFC-2026].
          Copies of claims of rights made available for publication and
          any assurances of licenses to be made available, or the result
          of an attempt made to obtain a general license or permission
          for the use of such proprietary rights by implementors or
          users of this specification can be obtained from the IETF

     10.  Full Copyright Statement

          Copyright (C) The Internet Society (2003).  All Rights

          This document and translations of it may be copied and
          furnished to others, and derivative works that comment on or
          otherwise explain it or assist in its implementation may be
          prepared, copied, published and distributed, in whole or in
          part, without restriction of any kind, provided that the above
          copyright notice and this paragraph are included on all such
          copies and derivative works.  However, this document itself
          may not be modified in any way, such as by removing the
          copyright notice or references to the Internet Society or
          other Internet organizations, except as needed for the purpose
          of developing Internet standards in which case the procedures
          for copyrights defined in the Internet Standards process must
          be followed, or as required to translate it into languages
          other than English.

          The limited permissions granted above are perpetual and will
          not be revoked by the Internet Society or its successors or

          This document and the information contained herein is provided


          Funding for the RFC Editor function is currently provided by
          the Internet Society.

Christensen, Kimball, Solensky                                 [Page 20]

Html markup produced by rfcmarkup 1.129d, available from https://tools.ietf.org/tools/rfcmarkup/