[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: (draft-polk-mmusic-traffic-class-for-sdp) 00 01 02 03 04 05

Network WG                                                   James Polk
Internet-Draft                                           Subha Dhesikan
Expires: Sept 12, 2012                                       Paul Jones
Intended Status: Standards Track (PS)                     Cisco Systems
                                                         March 12, 2012



    The Session Description Protocol (SDP) 'trafficclass' Attribute
               draft-ietf-mmusic-traffic-class-for-sdp-01


Abstract

   This document proposes a new Session Description Protocol (SDP)
   attribute to identify the traffic class a session is requesting
   in its offer/answer exchange.



Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six
   months and may be updated, replaced, or obsoleted by other documents
   at any time.  It is inappropriate to use Internet-Drafts as
   reference material or to cite them other than as "work in progress."

   This Internet-Draft will expire on September 12, 2012.

Copyright Notice

   Copyright (c) 2011 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with
   respect to this document.  Code Components extracted from this
   document must include Simplified BSD License text as described in
   Section 4.e of the Trust Legal Provisions and are provided without
   warranty as described in the Simplified BSD License.




Polk, et al.             Expires Sept 12, 2012                 [Page 1]


Internet-Draft         SDP trafficclass Attribute              Mar 2012





Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .  2
   2.  Traffic Class Framework and String Definitions  . . . . . . .  5
   3.  Traffic Class Attribute Definition  . . . . . . . . . . . . . 11
   4.  Offer/Answer Behavior . . . . . . . . . . . . . . . . . . . . 15
       4.1 Offer Behavior  . . . . . . . . . . . . . . . . . . . . . 15
       4.2 Answer Behavior . . . . . . . . . . . . . . . . . . . . . 15
   5.  Security considerations . . . . . . . . . . . . . . . . . . . 16
   6.  IANA considerations . . . . . . . . . . . . . . . . . . . . . 17
   7.  Acknowledgments   . . . . . . . . . . . . . . . . . . . . . . 19
   8.  References  . . . . . . . . . . . . . . . . . . . . . . . . . 19
       8.1.  Normative References  . . . . . . . . . . . . . . . . . 19
       8.2.  Informative References  . . . . . . . . . . . . . . . . 20
       Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . 20
       Appendix  . . . . . . . . . . . . . . . . . . . . . . . . . . 20



   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].















1.  Introduction

   The Session Description Protocol (SDP) [RFC4566] provides a means
   for an offerer to describe the specifics of a session to an
   answerer, and for the answerer to respond back with its session
   specifics to the offerer.  These session specifics include offering
   the codec or codecs to choose from, the specific IP address and port
   number the offerer wants to receive the RTP stream(s) on/at, the
   particulars about the codecs the offerer wants considered or
   mandated, and so on.



Polk, et al.             Expires Sept 12, 2012                 [Page 2]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

   There are many facets within SDP to determine the Real-time
   Transport Protocol (RTP) [RFC3550] details for the session
   establishment between one or more endpoints, but identifying how the
   underlying network should process each stream still remains
   under-specified.

   The ability to identify a traffic flow by port number gives an
   indication to underlying network elements to treat traffic with
   dissimilar ports in a different way, the same or in groups the same
   - but different from other ports or groups of ports.

   Within the context of realtime communications, the labeling of an
   RTP session based on media descriptor lines as just a voice and/or
   video session is insufficient, and provides no guidelines to the
   underlying network on how to treat the traffic. A more granular
   labeling helps on several fronts to

   - inform application layer elements in the signaling path the
     intent of this session.

   - inform the network on how to treat the traffic if the network is
     configured to differentiate session treatments based on the type
     of session the RTP is, including the ability to provide call
     admission control based on the type of traffic in the network.

   - allow network monitoring/management of traffic types realtime and
     after-the-fact analysis.

   Some network operators want the ability to guarantee certain traffic
   gets a minimum amount of network bandwidth per link or through a
   series of links that perhaps makes up a network such as a campus or
   WAN, or a backbone. For example, a call center voice application
   gets at least 20% of a link as a minimum bandwidth allocation.

   Some network operators want the ability to allow certain users or
   devices access to greater bandwidth during non-busy hours, than
   during busy hours of the day. For example, all desktop video to
   operate at 1080p during non-peak times, but curtail a similar
   session between the same users or devices to 720p or 360p during
   peak hours.  Another example would be to reduce the frames per
   second (fps) rate, say from 30fps to 15fps. This case is not as
   clear as accepting or denying similar sessions during different
   times of the day, but tuning the access to the bandwidth based on
   the type of session. In other words, tune down the bandwidth for
   desktop video during peak hours to allow a 3-screen telepresense
   session that would otherwise look like the same type of traffic
   (RTP, and more granular, video).

   RFC 4594 established a guideline for classifying the various flows
   in the network and the Differentiated Services Codepoints (DSCP)
   that apply to many traffic types (table 3 of [RFC4594]), including
   RTP based voice and video traffic sessions. The RFC also defines the


Polk, et al.             Expires Sept 12, 2012                 [Page 3]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

   per hop network behavior that is strongly encouraged for each of
   these application traffic types based on the traffic characteristics
   and tolerances to delay, loss and jitter within each traffic class.

   Video was broken down into 4 categories in that RFC, and voice into
   another single category.  We do not believe this satisfies the
   technical and business requirements to accomplish sufficiently
   unique labeling of RTP traffic.

   A question arises about once we properly label the traffic, what
   does that get us?  This is a fair question, but out of scope for
   this document because that answer lies within other RFCs and IDs in
   other WGs and/or Areas (specifically the Transport Area).  That
   said, we can discuss some of the ideas here for completeness.

   If the application becomes aware of traffic labeling,

   - this can be coded into layer 3 mechanisms.

   - this can be coded into layer 4 protocols and/or mechanisms.

   - this can be coded into a combination of mechanisms and protocols.

   The layer 3 mechanism for differentiating traffic is either the port
   number or the Differentiated Services Codepoint (DSCP) value
   [RFC2474]. Within the public Internet, if the application is not
   part of a managed service, the DSCP likely will be best effort (BE).
   Within the corporate LAN, this is usually completely configurable
   and a local IT department can take full advantage of this labeling
   to shape and manage their network as they see fit. Communications
   between enterprise networks will likely have to take advantage of
   MPLS.

   Within a network core, where only MPLS is used, Diffserv typically
   does not apply. That said, Diffserv can be used to identify which
   traffic goes into which MPLS tunnels [RFC4124].

   Labeling realtime traffic types using a layer 4 protocol would
   likely mean RSVP [RFC2205] or NSIS [RFC4080]. RSVP has an
   Application Identifier (app-ID) defined in [RFC2872] that provides a
   means for carrying a traffic class label along the media path.  An
   advantage with this mechanism is for the label to inform each domain
   along the media path what type of traffic this traffic flow is, and
   allow each domain to adjust the appropriate DSCP (set by each domain
   for use within that domain). Meaning, if a DSCP is set by an
   endpoint or a router in the first domain and gets reset by a SP, the
   far end domain will be able to reset the DSCP to the intended
   traffic class. There is a proposed extension to RSVP which creates
   individual profiles for what goes into each app-ID field to describe
   these traffic classes [ID-RSVP-PROF], which will take advantage of
   what is described in this document.



Polk, et al.             Expires Sept 12, 2012                 [Page 4]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

   There are several proprietary mechanisms to take advantage of this
   labeling, but none of those will be discussed here.

   The idea of traffic - or service - identification is not new; it has
   been described in [RFC5897]. If that RFC is used as a guideline,
   identification that leads to stream differentiation can be quite
   useful.  One of the points within RFC 5897 is that users cannot be
   allowed to assign any identification (fraud is but one reason
   given). In addition, RFC 5897 recommends that service identification
   should be done in signaling, rather than guessing or deep packet
   inspection. The network will have to currently guess or perform deep
   packet inspection to classify and offer the service as per RFC 4594
   since such service identification information is currently not
   available in SDP and therefore to the network elements. Since SDP
   understands how each stream is created (i.e., the particulars of the
   RTP stream), this is the right place to have this service
   differentiated. Such service differentiation can then be
   communicated to and leveraged by the network.

   [Editor's Note: the words "traffic" and "service" are similar enough
                   that the above paragraph talks about RFC 5897's
                   "service identification", but this document is only
                   wanting to discuss and propose traffic indications
                   in SDP.]

   This document proposes a simple attribute line to identify the
   application a session is requesting in its offer/answer exchange.
   This document uses previously defined service class strings for
   consistency between IETF documents.

   This document modifies the traffic classes originally created in RFC
   4594 in Section 2, incrementing each class with application
   identifiers and optional adjective strings.  Section 3 defines the
   new SDP attribute "trafficclass". Section 4 discusses the offerer
   and answerer behavior when generating or receiving this attribute.


2.  Traffic Class Framework and String Definitions

   The framework of the traffic class attribute will have at least two
   parts, allowing for several more to be included. The intention is to
   have a parent class (e.g., Conversational) that merely serves as the
   anchor point for an application component that when paired together,
   form the highest level traffic class. An adjective component
   provides further granularity for the application. There can be more
   than one adjective within a traffic class label to further refine
   the uniqueness of a traffic class being described.

   The traffic class label will have the following structure,

      parent.application(.adjective)(.adjective)



Polk, et al.             Expires Sept 12, 2012                 [Page 5]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

   [Editor's Note: the above is not exactly the ABNF to be used.
                   The order is right. The parent and application
                   MUST appear (each only once) and zero or more
                   adjectives can appear.]

   Where
   1) the 1st component is the human understandable category;
   2) the 2nd component is the application;
   3) an optional 3rd component or series of components are
      adjective(s) used to further refine the application component;
      and

   The construction of the traffic class label for Telepresence video
   would follow the minimum form of:

      Conversational.video.immersive

   where there might be one or more adjective after '.immersive'.

   There is no traffic class or DSCP value associated with just
   "Conversational".  There is a traffic class associated with
   "Conversational.video", creating a differentiation between it and a
   "Conversational.video.immersive" traffic class, which would have
   DSCP associated with the latter traffic class, depending on local
   policy. Each parent component is defined below, as are several of
   application and adjective strings.

   [Editor's Note: We're not yet sure how much of what's below will be
                   proposed for IANA registration, but the 5 parent
                   components will be, as well as at least some
                   application components per parent component. Some
                   adjective components will also likely be proposed
                   for IANA registration.

   The 5 parent components of the traffic class attribute are as
   follows:

   o Conversational
   o Multimedia Conferencing
   o Real-Time Interactive
   o Multimedia Streaming
   o Broadcast


   The following application components of the traffic class attribute
   are as follows:

   o Audio
   o Video
   o Text
   o application-sharing
   o Presentation-data


Polk, et al.             Expires Sept 12, 2012                 [Page 6]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

   o Whiteboarding
   o Web (conference) chat/instant messaging
   o Gaming
   o Virtual-desktop (interactive)
   o Remote-desktop
   o Telemetry (e.g., NORAD missile control)
   o Multiplex (i.e., combined streams)
   o Webcast
   o IPTV
   o Live-events (though not the buffered ones)
   o surveillance


   The following adjective components of the traffic class attribute
   are as follows:

   o Immersive
   o avconf
   o Realtime-Text
   o web

   Each of the above 3 lists will be defined in the following
   subsections.


2.1 Conversational Parent Traffic Class

   The Conversational traffic class is best suited for applications
   that require very low delay variation and generally intended to
   enable real-time, bi-directional person-to-person or
   multi-directional via an MTP communication, such as the following
   application components:

   o Audio (voice)**

   o Video**

   o Text (i.e., real-time text required by deaf users)

   **The above applications will also be used within Multimedia
     Streaming and Broadcast

   With adjective substrings to the above

   Immersive (TP) - An interactive audio-visual communications
        experience between remote locations, where the users enjoy a
        strong sense of realism and presence between all participants
        by optimizing a variety of attributes such as audio and video
        quality, eye contact, body language, spatial audio,
        coordinated environments and natural image size.

   Desktop-video - An interactive audio-visual communication


Polk, et al.             Expires Sept 12, 2012                 [Page 7]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

        experience that is not immersive in nature, though can have a
        high resolution video component.

   Realtime-Text (RTT) - a term for real-time transmission of text in
        a character-by-character fashion for use in conversational
        services, often as a text equivalent to voice-based
        conversational services. Conversational text is defined in the
        ITU-T Framework for multimedia services, Recommendation F.700
        [RFC5194].

   Web - for realtime aspects of web conferencing; mutually exclusive
        of both Immersive and Desktop video experiences

+--------------------------------------------------------------------+
 |Traffic Class  |                               |    Tolerance to    |
 |    Name       |  Traffic Characteristics      | Loss |Delay |Jitter|
 |===============+===============================+======+======+======|
 |               | High priority, typically      | Very | Very | Very |
 |Conversational | small packets (large video    |  Low |  Low |  Low |
 |               | frames produce large packets),|      |      |      |
 |               | generally sustained high      |      |      |      |
 |               | packet rate, low inter-packet |      |      |      |
 |               | transmission interval,        |      |      |      |
 |               | usually UDP framed in (S)RTP  |      |      |      |
 +---------------+-------------------------------+------+------+------+

       Figure 1. Conversational Traffic Characteristics


2.2 Multimedia-Conferencing Parent Traffic Class

   Multimedia-Conferencing traffic class is best suited for
   applications that are generally intended for communication between
   human users, but are less demanding in terms of delay, packet loss,
   and jitter than what Conversational applications require.  These
   applications require low to medium delay and may have the ability to
   change encoding rate (rate adaptive) or transmit data at varying
   rates, such as the following application component:

   o application-sharing (that webex does or protocols like T.128) -
        An application that shares the output of one or more running
        applications or the desktop on a host. This can utilize
        vector graphics, raster graphics or video.

   o Presentation-data - can be a series of still images or motion
        video.

   o Whiteboarding - an application enabling the exchange of graphical
        information including images, pointers and filled and
        unfilled parametric drawing elements (points, lines,
        polygons and ellipses).



Polk, et al.             Expires Sept 12, 2012                 [Page 8]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

   o (RTP-based) file transfer

   o Web (conference) chat/instant messaging

 +--------------------------------------------------------------------+
 |Traffic Class  |                               |    Tolerance to    |
 |    Name       |  Traffic Characteristics      | Loss |Delay |Jitter|
 |===============+===============================+======+======+======|
 |  Multimedia   | Variable size packets,        | Low  | Low  | Low  |
 | Conferencing  | Variable transmit interval,   |  -   |  -   |  -   |
 |               | rate adaptive, reacts to      |Medium|Medium|Medium|
 |               | loss, usually TCP-based       |      |      |      |
 +---------------+-------------------------------+------+------+------+

       Figure 2. Multimedia Conferencing Traffic Characteristics


2.3 Realtime-Interactive Parent Traffic Class

   Realtime-Interactive traffic class is intended for interactive
   variable rate inelastic applications that require low jitter and
   loss and very low delay, such as the following application
   components:

   o Gaming - interactive player video games with other users on other
        hosts (e.g., Doom)

   o Virtualized desktop (interactive) - similar to an X-windows
        station, has no local hard drive, or is operating an
        application with nolocal storage

   o Remote Desktop - controlling a remote node with local peripherals
        (i.e., monitor, keyboard and mouse)

   o Telemetry - a communication that allows remote measurement and
        reporting of information (e.g., post launch missile status or
        energy monitoring)

 +--------------------------------------------------------------------+
 |Traffic Class  |                               |    Tolerance to    |
 |    Name       |  Traffic Characteristics      | Loss |Delay |Jitter|
 |===============+===============================+======+======+======|
 |   Realtime    | Inelastic, mostly variable    | Low  | Very | Low  |
 |  Interactive  | rate, rate increases with     |      | Low  |      |
 |               | user activity                 |      |      |      |
 +---------------+-------------------------------+------+------+------+

       Figure 3. Realtime Interactive Traffic Characteristics


2.4 Multimedia-Streaming Parent Traffic Class



Polk, et al.             Expires Sept 12, 2012                 [Page 9]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

   Multimedia-Streaming traffic class is best suited for variable rate
   elastic streaming media applications where a human is waiting for
   output and where the application has the capability to react to
   packet loss by reducing its transmission rate, such as the following
   application components:

   o Audio

   o Video

   o Multiplex (i.e., combined a/v streams)

   With adjective substrings to the above (which may or may not get
   IANA registered)

   Webcast

   The primary difference from the Multimedia-streaming parent class
   and the Broadcast parent class is about the length of time for
   buffering. Buffered streaming audio and/or video which are initiated
   by SDP, and not HTTP. Buffering here can be from many seconds to
   hours, and is typically at the destination end (as opposed to
   Broadcast buffering which is minimal at the destination). The
   buffering aspect is what differentiates this parent class from the
   Broadcast class (which has minimal or no buffering).

 +--------------------------------------------------------------------+
 |Traffic Class  |                               |    Tolerance to    |
 |    Name       |  Traffic Characteristics      | Loss |Delay |Jitter|
 |===============+===============================+======+======+======|
 |  Multimedia   | Variable size packets,        |Low - |Medium| High |
 |   Streaming   | elastic with variable rate    |Medium|- High|      |
 |               |                               |      |      |      |
 +---------------+-------------------------------+------+------+------+

       Figure 4. Multimedia Streaming Traffic Characteristics


2.5 Broadcast Parent Traffic Class

   Broadcast traffic class is best suited for inelastic streaming media
   Applications, which might have a 'wardrobe malfunction' delay at or
   near the source but not typically at the destination, that may be of
   constant or variable rate, requiring low jitter and very low packet
   loss, such as the following application components:

   o Audio

   o Video

   o Multiplex (i.e., combined a/v streams)



Polk, et al.             Expires Sept 12, 2012                [Page 10]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

   With adjective substrings to the above:

   o IPTV

   o Live events (non-buffered)

   o Video surveillance -  one way video from a camera (e.g., observing
             a parking lot or building exit), typically enabled for
             long periods of time, usually stored at the destination.

 +--------------------------------------------------------------------+
 |Traffic Class  |                               |    Tolerance to    |
 |    Name       |  Traffic Characteristics      | Loss |Delay |Jitter|
 |===============+===============================+======+======+======|
 |   Broadcast   | Constant and variable rate,   | Very |Low - |Low - |
 |               | inelastic, generally          | Low  |Medium|Medium|
 |               | non-bursty flows, generally   |      |      |      |
 |               | sustained high packet rate,   |      |      |      |
 |               | low inter-packet transmission |      |      |      |
 |               | interval, usually UDP framed  |      |      |      |
 |               | in (S)RTP                     |      |      |      |
 +---------------+-------------------------------+------+------+------+

       Figure 5. Broadcast Traffic Characteristics


3. SDP Attribute Definition

   This document proposes the 'trafficclass' session and media-level
   SDP [RFC4566] attribute.  The following is the Augmented
   Backus-Naur Form (ABNF) [RFC5234] syntax for this attribute, which
   is based on the SDP [RFC4566] grammar:

      attribute               =/ traffic-classification

      traffic-classification  = "trafficclass" ":" [SP] parent-class
                                 "." app-type *( adj-param )

      parent-class            = "Broadcast" /
                                "Realtime-Interactive" /
                                "Multimedia-Conferencing" /
                                "Multimedia-Streaming" /
                                "Conversational" /
                                extension-mech

      extension-mech          = token

      app-type                = "audio" / "video" / "text" /
                                "application-sharing" /
                                "presentation-data" / "whiteboarding" /
                                "webchat/IM" / "gaming" /
                                "virtual-desktop" / "remote-desktop" /


Polk, et al.             Expires Sept 12, 2012                [Page 11]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

                                "telemetry"/ "multiplex" / "webcast" /
                                "IPTV" / "live-events" /
                                "surveillance" / extension-mech

      adj-param               = "." unqualified-adjective /
                                   "." qualified-adjective

      unqualified-adjective   = "immersive" / "avconf" /
                                "Realtime-Text" /"web" /
                                 generic-param ; from RFC3261

      qualified-adjective     =  qual-category ":" q-adjective

      qual-category           =  "aq" / extension-mech

      q-adjective             =  "admitted" / "non-admitted" / "none" /
                                  generic-param ; from RFC3261



   The attribute is named "trafficclass", for traffic classification,
   identifying which one of the five traffic classes applies to the
   media stream. There MUST NOT be more than one trafficclass attribute
   per media line. Confusion would result in where more than one exists
   per m= line.

   The parent classes in this document are an augmented version of the
   application labels introduced by table 3 of RFC 4595 (which will be
   rewritten based on the updated labels and treatments expected for
   each traffic class defined in this document).

    +-------------------------+------------------------------+
    | Application Labels      |   Parent Classes Defined     |
    | Defined in RFC 4594     |   in this document           |
    +=========================+==============================+
    | Broadcast-video         |   Broadcast                  |
    +-------------------------+------------------------------+
    | Realtime-Interactive    |   Realtime-Interactive       |
    +-------------------------+------------------------------+
    | Multimedia-Conferencing |   Multimedia-Conferencing    |
    +-------------------------+------------------------------+
    | Multimedia-Streaming    |   Multimedia-Streaming       |
    +-------------------------+------------------------------+
    | Telephony               |   Conversational             |
    +-------------------------+------------------------------+

       Figure 6. Label Changes from RFC 4594

   As is evident from the changes above, from left to right, two labels
   are different and each of the meanings are different in this
   document relative to how RFC 4594 defined them. These differences
   are articulated in Section 2 of this document.


Polk, et al.             Expires Sept 12, 2012                [Page 12]


Internet-Draft         SDP trafficclass Attribute              Mar 2012


   A parent class is a human understandable categorization, and MUST
   NOT be the only part of the traffic class label present in the
   attribute. The parent class string MUST always be paired with an
   application type, with a "." as the component separator.

   The application types (app-type) define the application of a
   particular traffic flow. The application types are listed both in
   the ABNF and defined in Section 2 of this document. Not every
   combination parent class is paired with application types, at least
   as defined in this document. Section 2.1 through 2.5 list many of
   the expected combinations.

   For additional application type granularity, adjective components
   can be added (also listed in Section 2). One or more adjectives can
   be within the same traffic class attribute. It is also permitted to
   include one or more non-IANA registered adjective component, but
   these MUST be prefaced by the additional delimiter "_", creating a
   possibility such as

    parent-class.application-type.adjective._non-standard-adjective
                                          ^^^^
                                     See the underscore

   For example, this is valid:

      m=video 50000 RTP/AVP 112
      a=trafficclass Conversational.video.immersive._foo._bar

   where both "foo" and "bar" are not IANA registered adjectives, but
   "immersive" is IANA registered. However, including non-registered
   adjectives without the "_" delimiter are not valid, such as the
   following:

      m=video 50000 RTP/AVP 112
      a=trafficclass Conversational.video.immersive.foo.bar

   There is no limit to the number of adjectives allowed, without
   regard for whether they are registered or not. These non-registered
   adjectives can be vendor generated, or merely considered to be
   proprietary in nature.

   It is important to note that the order of component types matter,
   but not the order of the adjective components. There might be local
   significance to the ordering though. In other words, the parent
   class component MUST be before the application component, which MUST
   be before the adjective component.

   Some algorithm such as alphabetizing the list and matching the
   understood strings SHOULD be used.

   Adjectives can be either unqualified or qualified. Qualified


Polk, et al.             Expires Sept 12, 2012                [Page 13]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

   adjectives have a designation it is qualified and a ":" separating
   the string component into two parts. We define this qualifying
   designation to have the form of a two or three letter qualifier, in
   which the last letter is always "q" (i.e., for "qualified").

   We are proposing in this document to have a single qualified
   adjective indicating whether this trafficclass has had or will have
   capacity-admission applied to it. Here we define the admission
   qualifier ("aq") with three possible values for this adjective:
   admitted, non-admitted and none, that will have the form

      aq:admitted|non-admitted|none

   Like all adjectives, it is OPTIONAL to include this adjective in any
   trafficclass attribute, and has the following meanings:

   - admitted - capacity admission mechanisms or protocols are to be or
                were used for the full amount of bandwidth in relation
                to this m= line.

   - non-admitted - capacity admission mechanisms or protocols were
                attempted but failed in relation to this m= line. This
                does not mean the flow described by this m= line
                failed. It just failed to attain the capacity admission
                mechanism or protocol necessary for a predictable
                quality of service, and is likely to continue with only
                a class of service marking or best effort.

   - none -     no capacity admission mechanisms or protocols are or
                were attempted in relation to this m= line.

   The default for any flow generated from an m= line not having a
   trafficclass adjective of 'aq:admitted' or 'aq:non-admitted' MUST be
   the equivalent of 'aq:none', whether or not it is present.

   Any parent class, application, or adjective string component within
   this attribute that is not understood MUST be ignored, leaving all
   that is understood to be processed. Ignored string components SHOULD
   NOT be deleted, as a downstream entity could understand the
   component(s) and use it/them.

   Not understanding the parent class string SHOULD mean that this
   attribute is ignored.

   The following is an example of media level description with a
   'trafficclass' attribute:

      m=video 50000 RTP/AVP 112
      a=trafficclass conversational.video.immersive.aq:admitted

   The above indicates a telepresence session that has had capacity
   admission process applied to its media flow.


Polk, et al.             Expires Sept 12, 2012                [Page 14]


Internet-Draft         SDP trafficclass Attribute              Mar 2012


4.  Offer/Answer Behavior

   Through the inclusion of the 'trafficclass' attribute, an
   offer/answer exchange identifies the application type for use by
   endpoints within a session.  Policy elements can use this attribute
   to determine the acceptability and/or treatment of that session
   through lower layers. One specific use-case is for setting of the
   DSCP specific for that application type (say a Broadcast instead
   of a Conversational video), decided on a per domain basis -
   instead of exclusively by the offering domain.


4.1 Offer Behavior

   Offerers include the 'trafficclass' attribute with a single string
   comprised of two or more components (from the list in Section 2) to
   obtain configurable and predictable classification between the
   answerer and the offerer. The offerer can also include a private set
   of components, or a combination of IANA registered and private
   components within a single domain (e.g., enterprise networks).

   Offerers of this 'trafficclass' attribute MUST NOT change the label
   in transit (e.g., wrt to B2BUAs). Session Border Controllers (SBC)
   at domain boundaries can change this attribute through local policy.

   Offers containing a 'trafficclass' label not understood are ignored
   by default (i.e., as if there was no 'trafficclass' attribute in the
   offer).


4.2 Answer Behavior

   Upon receiving an offer containing a 'trafficclass' attribute, if
   the offer is accepted, the answerer will use this attribute to
   classify the session or media (level) traffic accordingly towards
   the offerer. This answer does not need to match the traffic class in
   the offer, though this will likely be the case most of the time.

   In order to understand the traffic class attribute, the answerer
   MUST check several components within the attribute, such as

   1 - does the answerer understand the parent component?

       If not, the attribute SHOULD be ignored.

       If yes, it checks the application component.

   2 - does the answerer understand the application component?

       If not, the answerer needs to check if it has a local policy to
       proceed without an application component. The default for this


Polk, et al.             Expires Sept 12, 2012                [Page 15]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

       situation is as if the parent component was not understand,
       the attribute SHOULD be ignored.

       If yes, it checks to see if there are any other components
       present in this attribute to start its classification.


   3 - does the answerer understand the adjective component or
       components if any are present?

       If not present, process and match the trafficclass label value
       as is.

       If yes, determine if there is more than one. Search for each
       that is understood. Any adjectives not understood are to be
       ignored, as if they are not present.


   The answerer will answer the offer with its own 'trafficclass'
   attribute, which will likely be the same value, although this is not
   mandatory (at this time). The Offerer will process the received
   answer just as the answerer processed the offer. In other words, the
   processing steps and rules are identical for each end.

   The answerer should expect to receive RTP packets marked as
   indicated by its 'trafficclass' attribute in the answer itself.

   An Answer MAY have a 'trafficclass' attribute when one was not in
   the offer.  This will at least aid the local domain, and perhaps
   each domain the session transits, to categorize the application type
   of this RTP session.

   Answerers that are middleboxes can use the 'trafficclass' attribute
   to classify the RTP traffic within this session however local policy
   determines.  In other words, this attribute can help in deciding
   which DSCP an RTP stream is assigned within a domain, if the
   answerer were an inbound SBC to a domain.


5.  Security considerations

   RFC 5897 [RFC5897] discusses many of the pitfalls of service
   classification, which is similar enough to this idea of traffic
   classification to apply here as well.  That document highly
   recommends the user not being able to set any classification.
   Barring a hack within an endpoint (i.e., to intentionally
   misclassifying (i.e., lying) about which classification an RTP
   stream is), this document's solution makes the classification part
   of the signaling between endpoints, which is recommended by RFC
   5897.




Polk, et al.             Expires Sept 12, 2012                [Page 16]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

6.  IANA considerations

6.1 Registration of the SDP 'trafficclass' Attribute

   This document requests IANA to register the following SDP att-field
   under the Session Description Protocol (SDP) Parameters registry:

   Contact name:   jmpolk@cisco.com

   Attribute name:   trafficclass

   Long-form attribute name:   Traffic Classification

   Type of attribute:   Session and Media levels

   Subject to charset:   No

   Purpose of attribute:   To indicate the Traffic Classification
                           application for this session

   Allowed attribute values:   IANA Registered Tokens

   Registration Procedures: Specification Required

   Type            SDP Name                     Reference
   ----            ------------------           ---------
   att-field (both session and media level)

                   trafficclass                [this document]


6.2 The Traffic Classification Application Type Registration

   This document requests IANA to create a new registry for the
   traffic application classes similar to the following table within
   the Session Description Protocol (SDP) Parameters registry:

   Registry Name: "trafficclass" SDP Application Type Attribute Values
   Reference: [this document]
   Registration Procedures: Specification Required

   Parent Values                 Reference
   ----------------              ---------
   Broadcast                     [this document]
   Realtime-Interactive          [this document]
   Multimedia-Conferencing       [this document]
   Multimedia-Streaming          [this document]
   Conversational                [this document]


6.3 The Traffic Classification Application Type Registration



Polk, et al.             Expires Sept 12, 2012                [Page 17]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

   This document requests IANA to create a new registry for the
   traffic application classes similar to the following table
   within the Session Description Protocol (SDP) Parameters registry:

   Registry Name: "trafficclass" Attribute Application Type Values
   Reference: [this document]
   Registration Procedures: Specification Required

   Application Values            Reference
   ------------------            ---------
   Audio                         [this document]
   Video                         [this document]
   Text                          [this document]
   Application-sharing           [this document]
   Presentation-data             [this document]
   Whiteboarding                 [this document]
   Webchat/instant messaging     [this document]
   Gaming                        [this document]
   Virtualized-desktop           [this document]
   Remote-desktop                [this document]
   Telemetry                     [this document]
   Multiplex                     [this document]
   Webcast                       [this document]
   IPTV                          [this document]
   Live-event                    [this document]
   surveillance                  [this document]


6.4 The Traffic Classification Unqualified Adjective Registration

   This document requests IANA to create a new registry for the
   traffic unqualified adjective values similar to the following table
   within the Session Description Protocol (SDP) Parameters registry:

   Registry Name: "trafficclass" Attribute Unqualified Adjective Values
   Reference: [this document]
   Registration Procedures: Specification Required


   Application Values            Reference
   ------------------            ---------
   Immersive                     [this document]
   Desktop-video                 [this document]
   Realtime-Text                 [this document]
   web                           [this document]


6.5 The Traffic Classification Attribute Qualified Adjective Values
                               Registration

   This document requests IANA to create a new registry Qualified
   Adjective Values similar to the following table within the Session


Polk, et al.             Expires Sept 12, 2012                [Page 18]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

   Description Protocol (SDP) Parameters registry:

   Registry Name: "trafficclass" Attribute Qualified Adjective Values
   Reference: [this document]
   Registration Procedures: Specification Required

   Qualification Category   Attribute Values           Reference
   ----------------------   ----------------           ---------
    AQ                      Admitted                   [this document]
    AQ                      Non-admitted               [this document]
    AQ                      None                       [this document]


7.  Acknowledgments

   To Dave Oran, Toerless Eckert, Henry Chen, David Benham, David
   Benham, Mo Zanty, Michael Ramalho, Glen Lavers, Charles Ganzhorn,
   and Greg Edwards for their comments and suggestions.


8.  References

8.1.  Normative References

 [RFC2119] S. Bradner, "Key words for use in RFCs to Indicate
           Requirement Levels", RFC 2119, March 1997

 [RFC2205] R. Braden, Ed., L. Zhang, S. Berson, S. Herzog, S. Jamin,
           "Resource ReSerVation Protocol (RSVP) -- Version 1
           Functional Specification", RFC 2205, September 1997

 [RFC2474] K. Nichols, S. Blake, F. Baker, D. Black, "Definition of the
           Differentiated Services Field (DS Field) in the IPv4 and
           IPv6 Headers ", RFC 2474, December 1998

 [RFC2872] Y. Bernet, R. Pabbati, "Application and Sub Application
           Identity Policy Element for Use with RSVP", RFC 2872,
           June 2000

 [RFC3550] Schulzrinne, H., Casner, S., Frederick, R., and V.
           Jacobson, "RTP: A Transport Protocol for Real-Time
           Applications", STD 64, RFC 3550, July 2003.

 [RFC4080] R. Hancock, G. Karagiannis, J. Loughney, S. Van den Bosch,
           "Next Steps in Signaling (NSIS): Framework", RFC 4080, June
           2005

 [RFC4124] F. Le Faucheur, Ed., " Protocol Extensions for Support of
           Diffserv-aware MPLS Traffic Engineering ", RFC 4124,
           June 2005

 [RFC4566] M. Handley, V. Jacobson, C. Perkins, "SDP: Session


Polk, et al.             Expires Sept 12, 2012                [Page 19]


Internet-Draft         SDP trafficclass Attribute              Mar 2012

           Description Protocol", RFC 4566, July 2006

 [RFC5234] Crocker, D., Ed., and P. Overell, "Augmented BNF for Syntax
           Specifications: ABNF", STD 68, RFC 5234, January 2008.

 [RFC5865] F. Baker, J. Polk, M. Dolly, "A Differentiated Services Code
           Point (DSCP) for Capacity-Admitted Traffic", RFC 5865,
           May 2010

 [RFC5897] J. Rosenberg, "Identification of Communications Services in
           the Session Initiation Protocol (SIP)", RFC 5897, June 2010


8.2.  Informative References

 [RFC4594] J. Babiarz, K. Chan, F Baker, "Configuration Guidelines for
           Diffserv Service Classes", RFC 4594, August 2006

 [ID-RSVP-PROF] J. Polk, S. Dhesikan, "Resource Reservation Protocol
           (RSVP) Application-ID Profiles for Voice and Video Streams",
           work in progress, Mar 2011


Author's Addresses

   James Polk
   3913 Treemont Circle
   Colleyville, Texas, USA
   +1.818.271.3552

   mailto: jmpolk@cisco.com


   Subha Dhesikan
   170 W Tasman St
   San Jose, CA, USA
   +1.408-902-3351

   mailto: sdhesika@cisco.com


   Paul E. Jones

   mailto: paulej@packetizer.com


Appendix - Changes from Previous Versions

A.1  From -00 to -01

   These are the following changes made between the WG -00 version and
   the -01 version:


Polk, et al.             Expires Sept 12, 2012                [Page 20]


Internet-Draft         SDP trafficclass Attribute              Mar 2012


   - removed the non-SDP applications Netflix and VOD

   - switched the adjective 'desktop' to 'avconf'

   - Labeled each of the figures.

   - clarified the differences between Multimedia-Streaming and
     Broadcast parent categories.

   - defined Video surveillance

   - added the concept of a 'qualified' adjective, and modified the
     ABNF.

   - deleted the idea of a 'cac-class' as a separate component, and
     made the equivalent a qualified adjective.

   - modified the answerer behavior because of the removal of the
     'cac-class' component.

   - created an IANA registry for qualified adjectives

   - general clean-up of the doc.

   Did *not* do the following in this version:

   - add the ability to have more than one trafficclass attribute based
     on the codec chosen, as feedback indicated this was a bad idea.

   - no swap of the Multimedia-Conferencing parent category with the
     offered Collaboration parent category, as doing this did not solve
     any perceived problems.

   - add more to the 'how does this get processed' portion of Section
     3. That will come in the next revision.


















Polk, et al.             Expires Sept 12, 2012                [Page 21]

Html markup produced by rfcmarkup 1.129b, available from https://tools.ietf.org/tools/rfcmarkup/