[Docs] [txt|pdf|xml|html] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits] [IPR]

Versions: (draft-akiya-mpls-entropy-lsp-ping) 00 01 02 03 04 05 RFC 8012

MPLS Working Group                                              N. Akiya
Internet-Draft                                       Big Switch Networks
Updates: 6790 (if approved)                                   G. Swallow
Intended status: Standards Track                            C. Pignataro
Expires: March 9, 2017                                             Cisco
                                                                A. Malis
                                                     Huawei Technologies
                                                               S. Aldrin
                                                                  Google
                                                       September 5, 2016


     Label Switched Path (LSP) and Pseudowire (PW) Ping/Trace over
                 MPLS Network using Entropy Labels (EL)
                  draft-ietf-mpls-entropy-lsp-ping-05

Abstract

   Multiprotocol Label Switching (MPLS) Label Switched Path (LSP) Ping
   and Traceroute are methods used to test Equal-Cost Multipath (ECMP)
   paths.  Ping is known as a connectivity verification method and
   Traceroute as a fault isolation method, as described in RFC 4379.
   When an LSP is signaled using the Entropy Label (EL) described in RFC
   6790, the ability for LSP Ping and Traceroute operations to discover
   and exercise ECMP paths is lost for scenarios where Label Switching
   Routers (LSRs) apply different load balancing techniques.  One such
   scenario is when some LSRs apply EL-based load balancing while other
   LSRs apply non-EL-based load balancing (e.g., IP).  Another scenario
   is when an EL-based LSP is stitched with another LSP which can be EL-
   based or non-EL-based.

   This document extends the MPLS LSP Ping and Traceroute multipath
   mechanisms in RFC 6424 to allow the ability of exercising LSPs which
   make use of the EL.  This document updates RFC 6790.

Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute



Akiya, et al.             Expires March 9, 2017                 [Page 1]


Internet-Draft            LSP Ping over Entropy           September 2016


   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on March 9, 2017.

Copyright Notice

   Copyright (c) 2016 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
     1.1.  Terminology . . . . . . . . . . . . . . . . . . . . . . .   3
     1.2.  Background  . . . . . . . . . . . . . . . . . . . . . . .   4
   2.  Overview  . . . . . . . . . . . . . . . . . . . . . . . . . .   5
   3.  Multipath Type 9  . . . . . . . . . . . . . . . . . . . . . .   7
   4.  Pseudowire Tracing  . . . . . . . . . . . . . . . . . . . . .   7
   5.  Entropy Label FEC . . . . . . . . . . . . . . . . . . . . . .   8
   6.  DS Flags: L and E . . . . . . . . . . . . . . . . . . . . . .   9
   7.  New Multipath Information Type: TBD4  . . . . . . . . . . . .  10
   8.  Initiating LSR Procedures . . . . . . . . . . . . . . . . . .  11
   9.  Responder LSR Procedures  . . . . . . . . . . . . . . . . . .  13
     9.1.  IP-based Load Balancer & Not Pushing ELI/EL . . . . . . .  14
     9.2.  IP Based Load Balancer & Pushes ELI/EL  . . . . . . . . .  14
     9.3.  Label-based Load Balancer & Not Pushing ELI/EL  . . . . .  15
     9.4.  Label-based Load Balancer & Pushes ELI/EL . . . . . . . .  16
     9.5.  Flow-Aware MS-PW Stitching LSR  . . . . . . . . . . . . .  17
   10. Supported and Unsupported Cases . . . . . . . . . . . . . . .  17
   11. Security Considerations . . . . . . . . . . . . . . . . . . .  19
   12. IANA Considerations . . . . . . . . . . . . . . . . . . . . .  19
     12.1.  Entropy Label FEC  . . . . . . . . . . . . . . . . . . .  19
     12.2.  DS Flags . . . . . . . . . . . . . . . . . . . . . . . .  19



Akiya, et al.             Expires March 9, 2017                 [Page 2]


Internet-Draft            LSP Ping over Entropy           September 2016


     12.3.  Multipath Type . . . . . . . . . . . . . . . . . . . . .  20
   13. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  20
   14. Contributing Authors  . . . . . . . . . . . . . . . . . . . .  20
   15. References  . . . . . . . . . . . . . . . . . . . . . . . . .  20
     15.1.  Normative References . . . . . . . . . . . . . . . . . .  20
     15.2.  Informative References . . . . . . . . . . . . . . . . .  21
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  21

1.  Introduction

1.1.  Terminology

   The following acronyms and terms are used in this document:

   o  MPLS - Multiprotocol Label Switching.

   o  LSP - Label Switched Path.

   o  Stitched LSP - Stitched Label Switched Paths combine several LSPs
      such that a single end-to-end (e2e) LSP is realized.  [RFC6424]
      describes LSP Ping for Stitched LSPs.

   o  LSR - Label Switching Router.

   o  FEC - Forwarding Equivalence Class.

   o  ECMP - Equal-Cost Multipath.

   o  EL - Entropy Label.

   o  ELI - Entropy Label Indicator.

   o  GAL - Generic Associated Channel Label.

   o  MS-PW - Multi-Segment Pseudowire.

   o  Initiating LSR - LSR which sends an MPLS echo request.

   o  Responder LSR - LSR which receives an MPLS echo request and sends
      an MPLS echo reply.

   o  IP-Based Load Balancer - LSR which load balances on fields from an
      IP header (and possibly fields from upper layers), and does not
      consider an entropy label from an MPLS label stack (i.e., flow
      label [RFC6391] or entropy label [RFC6790]) for load balancing
      purposes.





Akiya, et al.             Expires March 9, 2017                 [Page 3]


Internet-Draft            LSP Ping over Entropy           September 2016


   o  Label-Based Load Balancer - LSR which load balances on an entropy
      label from an MPLS label stack (i.e., flow label or entropy
      label), and does not consider fields from an IP header (and
      possibly fields from upper layers) for load balancing purposes.

   o  Label and IP-Based Load Balancer - LSR which load balances on both
      entropy labels from an MPLS label stack and fields from an IP
      header (and possibly fields from upper layers).

1.2.  Background

   MPLS implementations employ a wide variety of load balancing
   techniques in terms of fields used for hash "keys".  The mechanisms
   in [RFC4379] and updated by [RFC6424] are designed to provide
   multipath support for a subset of techniques.  The intent of this
   document is to provide multipath support for the supported techniques
   which are compromised by the use of ELs [RFC6790].  Section 10
   describes supported and unsupported cases, and it may be useful for
   the reader to first review this section.

   The Downstream Detailed Mapping (DDMAP) TLV [RFC6424] provides
   Multipath Information which can be used by an LSP Ping initiator to
   trace and validate ECMP paths between an ingress and egress.  The
   Multipath Information encodings defined by [RFC6424] are sufficient
   when all the LSRs along the path(s), between ingress and egress,
   consider the same set of "keys" as input for load balancing
   algorithms, e.g., either all IP-based or all label-based.

   With the introduction of [RFC6790], some LSRs may perform load
   balancing based on labels while others may be IP-based.  This results
   in an LSP Ping initiator that is unable to trace and validate all the
   ECMP paths in the following scenarios:

   o  One or more transit LSRs along an LSP with ELI/EL in the label
      stack do not perform ECMP load balancing based on EL (hashes based
      on "keys" including the IP destination address).  This scenario is
      not only possible but quite common due to transit LSRs not
      implementing [RFC6790] or transit LSRs implementing [RFC6790], but
      not implementing the suggested transit LSR behavior in Section 4.3
      of [RFC6790].

   o  Two or more LSPs stitched together with at least one of these LSPs
      pushing ELI/EL into the label stack.

   These scenarios can be quite common because deployments of [RFC6790]
   typically have a mixture of nodes that support ELI/EL and nodes that
   do not.  There will also typically be a mixture of areas that support
   ELI/EL and areas that do not.



Akiya, et al.             Expires March 9, 2017                 [Page 4]


Internet-Draft            LSP Ping over Entropy           September 2016


   As pointed out in [RFC6790], the procedures of [RFC4379] (and
   consequently of [RFC6424]) with respect to Multipath Information Type
   {9} are incomplete.  However, [RFC6790] does not actually update
   [RFC4379].  Further, the specific EL location is not clearly defined,
   particularly in the case of Flow Aware Pseudowires [RFC6391].  This
   document defines a new FEC Stack sub-TLV for the entropy label.
   Section 3 of this document updates the procedures for Multipath
   Information Type {9} described in [RFC4379] and applicable to
   [RFC6424].  The rest of this document describes extensions required
   to restore ECMP discovery and tracing capabilities for the scenarios
   described.

   [RFC4379], [RFC6424], and this document will support IP-based load
   balancers and label-based load balancers which limit their hash to
   the first (top-most) or only entropy label in the label stack.  Other
   use cases (refer to Section 10) are out of scope.

2.  Overview

   [RFC4379] describes LSP traceroute as an operation where the
   initiating LSR sends a series of MPLS echo requests towards the same
   destination.  The first packet in the series has the TTL set to 1.
   When the echo reply is received from the LSR one hop away, the second
   echo request in the series is sent with the TTL set to 2.  For each
   additional echo request the TLL is incremented by one until a
   response is received from the intended destination.  The initiating
   LSR discovers and exercises ECMP by obtaining Multipath Information
   from each transit LSR and using a specific destination IP address or
   specific entropy label.

   From here on, the notation {x, y, z} refers to Multipath Information
   Types x, y, or z.  Multipath Information Types are defined in
   Section 3.3 of [RFC4379].

   The LSR initiating LSP Ping sends an MPLS echo request with Multipath
   Information.  This Multipath Information is described in the echo
   request's DDMAP TLV, and may contain a set of IP addresses or a set
   of labels.  Multipath Information Types {2, 4, 8} carry a set of IP
   addresses, and Multipath Information Type {9} carries a set of
   labels.  The responder LSR (the receiver of the MPLS echo request)
   will determine the subset of initiator-specified Multipath
   Information which load balances to each downstream (outgoing)
   interface.  The responder LSR sends an MPLS echo reply with resulting
   Multipath Information per downstream (outgoing interface) back to the
   initiating LSR.  The initiating LSR is then able to use a specific IP
   destination address or a specific label to exercise a specific ECMP
   path on the responder LSR.




Akiya, et al.             Expires March 9, 2017                 [Page 5]


Internet-Draft            LSP Ping over Entropy           September 2016


   The current behavior is problematic in the following scenarios:

   o  The initiating LSR sends IP Multipath Information, but the
      responder LSR load balances on labels.

   o  The initiating LSR sends Label Multipath Information, but the
      responder LSR load balances on IP addresses.

   o  The initiating LSR sends existing Multipath Information to an LSR
      which pushes ELI/EL in the label stack, but the initiating LSR can
      only continue to discover and exercise specific paths of the ECMP,
      if the LSR which pushes ELI/EL responds with both IP addresses and
      the associated EL corresponding to each IP address.  This is
      because:

      *  An ELI/EL-pushing LSR that is a stitching point will load
         balance based on the IP address.

      *  Downstream LSR(s) of an ELI/EL-pushing LSR may load balance
         based on ELs.

   o  The initiating LSR sends existing Multipath Information to an ELI/
      EL-pushing LSR, but the initiating LSR can only continue to
      discover and exercise specific paths of ECMP, if the ELI/EL-
      pushing LSR responds with both labels and the associated EL
      corresponding to the label.  This is because:

      *  An ELI/EL-pushing LSR that is a stitching point will load
         balance based on the EL from the previous LSP and pushes a new
         EL.

      *  Downstream LSR(s) of ELI/EL-pushing LSR may load balance based
         on new ELs.

   The above scenarios demonstrate the existing Multipath Information is
   insufficient when LSP traceroute is used on an LSP with entropy
   labels [RFC6790].  This document defines a new Multipath Information
   Type to be used in the DDMAP of MPLS echo request/reply packets for
   [RFC6790] LSPs.

   The responder LSR can reply with empty Multipath Information if no IP
   address is set or label set is received with the Multipath
   Information.  An empty return is also possible if an initiating LSR
   sends Multipath Information of one type, IP Address or Label, but the
   responder LSR load balances on the other type.  To disambiguate
   between the two results, this document introduces new flags in the
   DDMAP TLV to allow the responder LSR to describe the load balancing
   technique being used.



Akiya, et al.             Expires March 9, 2017                 [Page 6]


Internet-Draft            LSP Ping over Entropy           September 2016


   To use this enhanced method end-to-end, all LSRs along the LSP need
   to be able to understand the new flags and the new Multipath
   Information Type.  Mechanisms to verify this condition are outside of
   the scope of this document.  The rest of the requirements are
   detailed in the initiating LSR and responder LSR procedures.  Two
   additional DS Flags are defined for the DDMAP TLV in Section 6.
   These two flags are used by the responder LSR to describe its load
   balance behavior on a received MPLS echo request.

   Note that the terms "IP-Based Load Balancer" and "Label-Based Load
   Balancer" are in context of how a received MPLS echo request is
   handled by the responder LSR.

3.  Multipath Type 9

   [RFC4379] defined Multipath Type {9} for tracing of LSPs where label-
   based load balancing is used.  However, as pointed out in [RFC6790],
   the procedures for using this type are incomplete as the specific
   location of the label was not defined.  It was assumed that the
   presence of Multipath Type {9} implied the value of the bottom-of-
   stack label should be varied by the values indicated by multipath to
   determine the respective outgoing interfaces.

   Section 5 defines a new FEC-Stack sub-TLV to indicate an entropy
   label.  These labels MAY appear anywhere in a label stack.

   Multipath Type {9} applies to the first label in the label stack that
   corresponds to an EL-FEC.  If no such label is found, it applies to
   the label at the bottom of the label stack.

4.  Pseudowire Tracing

   This section defines procedures for tracing pseudowires.  These
   procedures pertain to the use of Multipath Information Type {9} as
   well as Type {TBD4}.  In all cases below, when a control word is in
   use, the N-flag in the DDMAP MUST be set.  Note that when a control
   word is not in use, the returned DDMAPs may not be accurate.

   In order to trace a non-flow-aware Pseudowire, the initiator includes
   an EL-FEC instead of the appropriate PW FEC at the bottom of the FEC
   stack.  Tracing in this way will cause compliant routers to return
   the proper outgoing interface.  Note that this procedure only traces
   to the end of the MPLS LSP that is under test and will not verify the
   PW FEC.  To actually verify the PW FEC or in the case of a MS-PW, to
   determine the next pseudowire label value, the initiator MUST repeat
   that step of the trace (i.e., repeating the TTL value used) but with
   the FEC Stack modified to contain the appropriate PW FEC.  Note that
   these procedures are applicable to scenarios where an initiator is



Akiya, et al.             Expires March 9, 2017                 [Page 7]


Internet-Draft            LSP Ping over Entropy           September 2016


   able to vary the bottom label (i.e., Pseudowire label).  Possible
   scenarios are tracing multiple non-flow-aware Pseudowires on the same
   endpoints or tracing a non-flow-aware Pseudowire provisioned with
   multiple Pseudowire labels.

   In order to trace a flow-aware Pseudowire [RFC6391], the initiator
   includes an EL FEC at the bottom of the FEC Stack and pushes the
   appropriate PW FEC onto the FEC Stack.

   In order to trace through non-compliant routers, the initiator forms
   an MPLS echo request message and includes a DDMAP with Multipath Type
   {9}. For a non-flow-aware Pseudowire it includes the appropriate PW
   FEC in the FEC Stack.  For a flow-aware Pseudowire, the initiator
   includes a Nil FEC at the bottom of the FEC Stack and pushes the
   appropriate PW FEC onto the FEC Stack.

5.  Entropy Label FEC

   The entropy label indicator (ELI) is a reserved label that has no
   explicit FEC associated, and has label value 7 assigned from the
   reserved range.  Use the Nil FEC as the Target FEC Stack sub-TLV to
   account for ELI in a Target FEC Stack TLV.

   The entropy label (EL) is a special purpose label with the label
   value being discretionary (i.e., the label value is not from the
   reserved range).  For LSP verification mechanics to perform its
   purpose, it is necessary for a Target FEC Stack sub-TLV to clearly
   describe the EL, particularly in the scenario where the label stack
   does not carry ELI (e.g., flow-aware Pseudowire [RFC6391]).
   Therefore, this document defines an EL FEC sub-TLV (TBD1, see
   Section 12.1) to allow a Target FEC Stack sub-TLV to be added to the
   Target FEC Stack to account for EL.

   The Length is 4.  Labels are 20-bit values treated as numbers.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                 Label                 |          MBZ          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

           Figure 1: Entropy Label FEC

   Label is the actual label value inserted in the label stack; the MBZ
   field MUST be zero when sent and ignored on receipt.






Akiya, et al.             Expires March 9, 2017                 [Page 8]


Internet-Draft            LSP Ping over Entropy           September 2016


6.  DS Flags: L and E

   Two flags, L and E, are added to the DS Flags field of the DDMAP TLV.
   Both flags MUST NOT be set in echo request packets when sending, and
   SHOULD be ignored when received.  Zero, one or both new flags MUST be
   set in echo reply packets.

    DS Flags
    --------

        0 1 2 3 4 5 6 7
       +-+-+-+-+-+-+-+-+
       |  MBZ  |L|E|I|N|
       +-+-+-+-+-+-+-+-+

   RFC-Editor-Note: Please update the above figure to place the flag E
   in the bit number TBD2 and the flag L in the bit number TBD3.

    Flag  Name and Meaning
    ----  ----------------
       L  Label-based load balance indicator
          This flag MUST be cleared in the echo request. An LSR
          which performs load balancing on a label MUST set this
          flag in the echo reply. An LSR which performs load
          balancing on IP MUST NOT set this flag in the echo
          reply.

       E  ELI/EL push indicator
          This flag MUST be cleared in the echo request. An LSR
          which pushes ELI/EL MUST set this flag in the echo
          reply. An LSR which does not push ELI/EL MUST NOT set
          this flag in the echo reply.

   The two flags result in four load balancing techniques which the echo
   reply generating LSR can indicate:

   o  {L=0, E=0} LSR load balances based on IP and does not push ELI/EL.

   o  {L=0, E=1} LSR load balances based on IP and pushes ELI/EL.

   o  {L=1, E=0} LSR load balances based on labels and does not push
      ELI/EL.

   o  {L=1, E=1} LSR load balances based on labels and pushes ELI/EL.







Akiya, et al.             Expires March 9, 2017                 [Page 9]


Internet-Draft            LSP Ping over Entropy           September 2016


7.  New Multipath Information Type: TBD4

   One new Multipath Information Type is added to be used in DDMAP TLV.
   This new Multipath Type has the value of TBD4.

     Key   Type                  Multipath Information
     ---   ----------------      ---------------------
    TBD4   IP and Label set      IP addresses and label prefixes

   Multipath Type TBD4 is comprised of three sections.  The first
   section describes the IP address set.  The second section describes
   the label set.  The third section describes another label set which
   associates to either the IP address set or the label set specified in
   the other sections.

   Multipath Information Type TBD4 has following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |IPMultipathType|     IP Multipath Length       | Reserved(MBZ) |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ~                                                               ~
   |                  (IP Multipath Information)                   |
   ~                                                               ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |LbMultipathType|    Label Multipath Length     | Reserved(MBZ) |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ~                                                               ~
   |                 (Label Multipath Information)                 |
   ~                                                               ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |  Assoc Label Multipath Length |         Reserved(MBZ)         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ~                                                               ~
   |            (Associated Label Multipath Information)           |
   ~                                                               ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

           Figure 2: Multipath Information Type TBD4

   o  IPMultipathType

      *  0 when "IP Multipath Information" is omitted.  Otherwise, one
         of the IP Multipath Information values: {2, 4, 8}.

   o  IP Multipath Information




Akiya, et al.             Expires March 9, 2017                [Page 10]


Internet-Draft            LSP Ping over Entropy           September 2016


      *  This section is omitted when "IPMultipathType" is 0.
         Otherwise, this section reuses IP Multipath Information from
         [RFC4379].  Specifically, Multipath Information for values {2,
         4, 8} can be used.

   o  LbMultipathType

      *  0 when "Label Multipath Information" is omitted.  Otherwise,
         Label Multipath Information value {9}.

   o  Label Multipath Information

      *  This section is omitted when "LbMultipathType" is 0.
         Otherwise, this section reuses Label Multipath Information from
         [RFC4379].  Specifically, Multipath Information for value {9}
         can be used.

   o  Associated Label Multipath Information

      *  "Assoc Label Multipath Length" is a 16-bit field of Multipath
         Information which indicates the length in octets of the
         Associated Label Multipath Information.

      *  "Associated Label Multipath Information" is a list of labels
         with each label described in 24 bits.  This section MUST be
         omitted in an MPLS echo request message.  A midpoint which
         pushes ELI/EL labels SHOULD include "Assoc Label Multipath
         Information" in its MPLS echo reply message, along with either
         "IP Multipath Information" or "Label Multipath Information".
         Each specified associated label described in this section maps
         to a specific IP address OR label described in the "IP
         Multipath Information" section or "Label Multipath Information"
         section.  For example, if three IP addresses are specified in
         the "IP Multipath Information" section, then there MUST be
         three labels described in this section.  The first label maps
         to the first IP address specified, the second label maps to the
         second IP address specified, and the third label maps to the
         third IP address specified.

   When a section is omitted, the length for that section MUST be set to
   zero.

8.  Initiating LSR Procedures

   The following procedure is described in terms of an EL_LSP boolean
   maintained by the initiating LSR.  This value controls the Multipath
   Information Type to be used in the transmitted echo request packets.
   When the initiating LSR is transmitting an echo request packet with



Akiya, et al.             Expires March 9, 2017                [Page 11]


Internet-Draft            LSP Ping over Entropy           September 2016


   DDMAP with a non-zero Multipath Information Type, then the EL_LSP
   boolean MUST be consulted to determine the Multipath Information Type
   to use.

   In addition to procedures described in [RFC4379], as updated by
   Section 3 and [RFC6424], the initiating LSR MUST operate with the
   following procedures:

   o  When the initiating LSR pushes ELI/EL, initialize EL_LSP=True.
      Else set EL_LSP=False.

   o  When the initiating LSR is transmitting a non-zero Multipath
      Information Type:

      *  If (EL_LSP), the initiating LSR MUST use Multipath Information
         Type {TBD4} unless the responder LSR cannot handle Type {TBD4}.
         When the initiating LSR is transmitting Multipath Information
         Type {TBD4}, both "IP Multipath Information" and "Label
         Multipath Information" MUST be included, and "Associated Label
         Multipath Information" MUST be omitted (NULL).

      *  Else the initiating LSR MAY use Multipath Information Type {2,
         4, 8, 9, TBD4}. When the initiating LSR is transmitting
         Multipath Information Type {TBD4} in this case, "IP Multipath
         Information" MUST be included, and "Label Multipath
         Information" and "Associated Label Multipath Information" MUST
         be omitted (NULL).

   o  When the initiating LSR receives an echo reply with {L=0, E=1} in
      the DS flags with valid contents, set EL_LSP=True.

   In the following conditions, the initiating LSR may have lost the
   ability to exercise specific ECMP paths.  The initiating LSR MAY
   continue with "best effort" in the following cases:

   o  Received echo reply contains empty Multipath Information.

   o  Received echo reply contains {L=0, E=<any>} DS flags, but does not
      contain IP Multipath Information.

   o  Received echo reply contains {L=1, E=<any>} DS flags, but does not
      contain Label Multipath Information.

   o  Received echo reply contains {L=<any>, E=1} DS flags, but does not
      contain Associated Label Multipath Information.

   o  IP Multipath Information Types {2, 4, 8} sent, and received echo
      reply with {L=1, E=0} in DS flags.



Akiya, et al.             Expires March 9, 2017                [Page 12]


Internet-Draft            LSP Ping over Entropy           September 2016


   o  Multipath Information Type {TBD4} sent, and received echo reply
      with Multipath Information Type other than {TBD4}.

9.  Responder LSR Procedures

   Common Procedures:

   o  The responder LSR receiving an MPLS echo request packet MUST first
      determine whether or not the initiating LSR supports this LSP Ping
      and Traceroute extension for Entropy Labels.  If either of the
      following conditions are met, the responder LSR SHOULD determine
      that the initiating LSR supports this LSP Ping and Traceroute
      extension for entropy labels.

      1.  Received MPLS echo request contains the Multipath Information
          Type {TBD4}.

      2.  Received MPLS echo request contains a Target FEC Stack TLV
          that includes the entropy label FEC.

      If the initiating LSR is determined not to support this LSP Ping
      and Traceroute extension for entropy labels, then the responder
      LSR MUST NOT follow further procedures described in this section.
      Specifically, MPLS echo reply packets:

      *  MUST have the following DS Flags cleared (i.e., not set): "ELI/
         EL push indicator" and "Label-based load balance indicator".

      *  MUST NOT use Multipath Information Type {TBD4}.

   o  The responder LSR receiving an MPLS echo request packet with
      Multipath Information Type {TBD4} MUST validate the following
      contents.  Any deviation MUST result in the responder LSR
      considering the packet as malformed and returning code 1
      ("Malformed echo request received") in the MPLS echo reply packet.

      *  IP Multipath Information MUST be included.

      *  Label Multipath Information MAY be included.

      *  Associated Label Multipath Information MUST be omitted (NULL).

   The following subsections describe expected responder LSR procedures
   when the echo reply is to include DDMAP TLVs, based on the local load
   balance technique being employed.  In case the responder LSR performs
   deviating load balance techniques on a per downstream basis,
   appropriate procedures matched to each downstream load balance
   technique MUST be followed.



Akiya, et al.             Expires March 9, 2017                [Page 13]


Internet-Draft            LSP Ping over Entropy           September 2016


9.1.  IP-based Load Balancer & Not Pushing ELI/EL

   o  The responder MUST set {L=0, E=0} in DS flags.

   o  If Multipath Information Type {2, 4, 8} is received, the responder
      MUST comply with [RFC4379] and [RFC6424].

   o  If Multipath Information Type {9} is received, the responder MUST
      reply with Multipath Type {0}.

   o  If Multipath Information Type {TBD4} is received, the following
      procedures are to be used:

      *  The responder MUST reply with Multipath Information Type
         {TBD4}.

      *  The "Label Multipath Information" and "Associated Label
         Multipath Information" sections MUST be omitted (NULL).

      *  If no matching IP address is found, then the "IPMultipathType"
         field MUST be set to Multipath Information Type {0} and the "IP
         Multipath Information" section MUST also be omitted (NULL).

      *  If at least one matching IP address is found, then the
         "IPMultipathType" field MUST be set to appropriate Multipath
         Information Type {2, 4, 8} and the "IP Multipath Information"
         section MUST be included.

9.2.  IP Based Load Balancer & Pushes ELI/EL

   o  The responder MUST set {L=0, E=1} in DS flags.

   o  If Multipath Information Type {9} is received, the responder MUST
      reply with Multipath Type {0}.

   o  If Multipath Type {2, 4, 8, TBD4} is received, the following
      procedures are to be used:

      *  The responder MUST respond with Multipath Type {TBD4}. See
         Section 7 for details of Multipath Type {TBD4}.

      *  The "Label Multipath Information" section MUST be omitted
         (i.e., it is not there).

      *  The IP address set specified in the received IP Multipath
         Information MUST be used to determine the returned IP/Label
         pairs.




Akiya, et al.             Expires March 9, 2017                [Page 14]


Internet-Draft            LSP Ping over Entropy           September 2016


      *  If the received Multipath Information Type was {TBD4}, the
         received "Label Multipath Information" sections MUST NOT be
         used to determine the associated label portion of the returned
         IP/Label pairs.

      *  If no matching IP address is found, then the "IPMultipathType"
         field MUST be set to Multipath Information Type {0} and the "IP
         Multipath Information" section MUST be omitted.  In addition,
         the "Assoc Label Multipath Length" MUST be set to 0, and the
         "Associated Label Multipath Information" section MUST also be
         omitted.

      *  If at least one matching IP address is found, then the
         "IPMultipathType" field MUST be set to appropriate Multipath
         Information Type {2, 4, 8} and the "IP Multipath Information"
         section MUST be included.  In addition, the "Associated Label
         Multipath Information" section MUST be populated with a list of
         labels corresponding to each IP address specified in the "IP
         Multipath Information" section.  "Assoc Label Multipath Length"
         MUST be set to a value representing the length in octets of the
         "Associated Label Multipath Information" field.

9.3.  Label-based Load Balancer & Not Pushing ELI/EL

   o  The responder MUST set {L=1, E=0} in DS flags.

   o  If Multipath Information Type {2, 4, 8} is received, the responder
      MUST reply with Multipath Type {0}.

   o  If Multipath Information Type {9} is received, the responder MUST
      comply with [RFC4379] and [RFC6424] as updated by Section 3.

   o  If Multipath Information Type {TBD4} is received, the following
      procedures are to be used:

      *  The responder MUST reply with Multipath Information Type
         {TBD4}.

      *  The "IP Multipath Information" and "Associated Label Multipath
         Information" sections MUST be omitted (NULL).

      *  If no matching label is found, then the "LbMultipathType" field
         MUST be set to Multipath Information Type {0} and the "Label
         Multipath Information" section MUST also be omitted (NULL).

      *  If at least one matching label is found, then the
         "LbMultipathType" field MUST be set to the appropriate




Akiya, et al.             Expires March 9, 2017                [Page 15]


Internet-Draft            LSP Ping over Entropy           September 2016


         Multipath Information Type {9} and the "Label Multipath
         Information" section MUST be included.

9.4.  Label-based Load Balancer & Pushes ELI/EL

   o  The responder MUST set {L=1, E=1} in DS flags.

   o  If Multipath Information Type {2, 4, 8} is received, the responder
      MUST reply with Multipath Type {0}.

   o  If Multipath Type {9, TBD4} is received, the following procedures
      are to be used:

      *  The responder MUST respond with Multipath Type {TBD4}.

      *  The "IP Multipath Information" section MUST be omitted.

      *  The label set specified in the received Label Multipath
         Information MUST be used to determine the returned Label/Label
         pairs.

      *  If received Multipath Information Type was {TBD4}, received
         "Label Multipath Information" sections MUST NOT be used to
         determine the associated label portion of the returned Label/
         Label pairs.

      *  If no matching label is found, then the "LbMultipathType" field
         MUST be set to Multipath Information Type {0} and "Label
         Multipath Information" section MUST be omitted.  In addition,
         "Assoc Label Multipath Length" MUST be set to 0, and the
         "Associated Label Multipath Information" section MUST also be
         omitted.

      *  If at least one matching label is found, then the
         "LbMultipathType" field MUST be set to the appropriate
         Multipath Information Type {9} and the "Label Multipath
         Information" section MUST be included.  In addition, the
         "Associated Label Multipath Information" section MUST be
         populated with a list of labels corresponding to each label
         specified in the "Label Multipath Information" section.  "Assoc
         Label Multipath Length" MUST be set to a value representing the
         length in octets of the "Associated Label Multipath
         Information" field.








Akiya, et al.             Expires March 9, 2017                [Page 16]


Internet-Draft            LSP Ping over Entropy           September 2016


9.5.  Flow-Aware MS-PW Stitching LSR

   A stitching LSR that cross-connects flow-aware Pseudowires behaves in
   one of two ways:

   o  Load balances on the previous flow label, and carries over the
      same flow label.  For this case, the stitching LSR is to behave as
      described in Section 9.3.

   o  Load balances on the previous flow label, and replaces the flow
      label with a newly computed label.  For this case, the stitching
      LSR is to behave as described in Section 9.4.

10.  Supported and Unsupported Cases

   The MPLS architecture does not define strict rules on how
   implementations are to identify hash "keys" for load balancing
   purposes.  As a result, implementations may be of the following load
   balancer types:

   1.  IP-based load balancer.
   2.  Label-based load balancer.
   3.  Label- and IP-based load balancer.

   For cases (2) and (3), an implementation can include different sets
   of labels from the label stack for load balancing purpose.  Thus the
   following sub-cases are possible:

   a.  Entire label stack.
   b.  Top N labels from label stack where the number of labels in label
       stack is > N.
   c.  Bottom N labels from label stack where the number of labels in
       label stack is > N.

   In a scenario where there is one flow label or entropy label present
   in the label stack, the following further cases are possible for
   (2b), (2c), (3b) and (3c):

   1.  N labels from label stack include flow label or entropy label.
   2.  N labels from label stack do not include flow label or entropy
       label.

   Also in a scenario where there are multiple entropy labels present in
   the label stack, it is possible for implementations to employ
   deviating techniques:

   o  Search for entropy stops at the first entropy label.




Akiya, et al.             Expires March 9, 2017                [Page 17]


Internet-Draft            LSP Ping over Entropy           September 2016


   o  Search for entropy includes any entropy label found plus continues
      to search for entropy in the label stack.

   Furthermore, handling of reserved (i.e., special) labels varies among
   implementations:

   o  Reserved labels are used in the hash as any other label would be
      (not a recommended practice.)
   o  Reserved labels are skipped over and, for implementations limited
      to N labels, the reserved labels do not count towards the limit of
      N.
   o  Reserved labels are skipped over and, for implementations limited
      to N labels, the reserved labels count towards the limit of N.

   It is important to point this out since the presence of GAL will
   affect those implementations which include reserved labels for load
   balancing purposes.

   As can be seen from the above, there are many types of potential load
   balancing implementations.  Attempting for any OAM tools to support
   ECMP discovery and traversal over all types would require fairly
   complex procedures.  Complexities in OAM tools have minimal benefit
   if the majority of implementations are expected to employ only a
   small subset of the cases described above.

   o  Section 4.3 of [RFC6790] states that in implementations, for load
      balancing purposes, parsing beyond the label stack after finding
      an entropy label has "limited incremental value".  Therefore, it
      is expected that most implementations will be of types "IP-based
      load balancer" or "Label-based load balancer".

   o  Section 2.4.5.1 of [RFC7325] recommends that searching for entropy
      labels in the label stack should terminate upon finding the first
      entropy label.  Therefore, it is expected that implementations
      will only include the first (top-most) entropy label when there
      are multiple entropy labels in the label stack.

   o  It is expected that, in most cases, the number of labels in the
      label stack will not exceed the number of labels (N) which
      implementations can include for load balancing purposes.

   o  It is expected that labels in the label stack, besides the flow
      label and entropy label, are constant for the lifetime of a single
      LSP multipath traceroute operation.  Therefore, deviating load
      balancing implementations with respect to reserved labels should
      not affect this tool.





Akiya, et al.             Expires March 9, 2017                [Page 18]


Internet-Draft            LSP Ping over Entropy           September 2016


   Thus [RFC4379], [RFC6424], and this document support cases (1) and
   (2a1), where only the first (top-most) entropy label is included when
   there are multiple entropy labels in the label stack.

11.  Security Considerations

   While [RFC4379] and [RFC6424] already allow for the discovery and
   exercise of ECMP paths, this document extends the LSP Ping and
   Traceroute mechanisms to more precisely discover and exercise ECMP
   paths when an LSP uses ELI/EL in the label stack.  Sourcing or
   inspecting LSP Ping packets can be used for network reconnaissance.

   The extended capability defined in this document requires small
   additional processing for the responder and initiator nodes.  The
   responder node that pushes ELI/EL will need to compute and return
   multipath data including associated EL.  The initiator node will need
   to store and handle both IP Multipath and Label Multipath
   Information, and include destination IP addresses and/or ELs in MPLS
   echo request packets as well as in Multipath Information sent to
   downstream nodes.  The security considerations of [RFC4379] already
   cover Denial-of-Service attacks by regulating LSP Ping traffic going
   to the control plane.

   Finally, the security measures described in [RFC4379], [RFC6424], and
   [RFC6790] are applicable.  [RFC6424] provides guidelines if a network
   operator wants to prevent tracing or does not want to expose details
   of the tunnel and [RFC6790] provides guidance on the use of the EL.

12.  IANA Considerations

12.1.  Entropy Label FEC

   The IANA is requested to assign a new sub-TLV from the "Sub-TLVs for
   TLV Types 1, 16, and 21" section from the "Multi-Protocol Label
   Switching (MPLS) Label Switched Paths (LSPs) Ping Parameters - TLVs"
   registry ([IANA-MPLS-LSP-PING]).

    Sub-Type Sub-TLV Name          Reference
    -------- ------------          ---------
    TBD1     Entropy label FEC     this document

12.2.  DS Flags

   The IANA is requested to assign new bit numbers from the "DS flags"
   sub-registry from the "Multi-Protocol Label Switching (MPLS) Label
   Switched Paths (LSPs) Ping Parameters - TLVs" registry
   ([IANA-MPLS-LSP-PING]).




Akiya, et al.             Expires March 9, 2017                [Page 19]


Internet-Draft            LSP Ping over Entropy           September 2016


   Note: the "DS flags" sub-registry is created by [RFC7537].

    Bit number Name                                        Reference
    ---------- ----------------------------------------    ---------
    TBD2       E: ELI/EL push indicator                    this document
    TBD3       L: Label-based load balance indicator       this document

12.3.  Multipath Type

   The IANA is requested to assign a new value from the "Multipath Type"
   sub-registry from the "Multi-Protocol Label Switching (MPLS) Label
   Switched Paths (LSPs) Ping Parameters - TLVs" registry
   ([IANA-MPLS-LSP-PING]).

   Note: The "Multipath Type" sub-registry is created by [RFC7537].

    Value      Meaning                                  Reference
    ---------- ---------------------------------------- ---------
     TBD4      IP and label set                         this document

13.  Acknowledgements

   The authors would like to thank Loa Andersson, Curtis Villamizar,
   Daniel King, Sriganesh Kini, Victor Ji, Acee Lindem, Deborah
   Brungard, Shawn M Emery, Scott O. Bradner, and Peter Yee for
   performing thorough reviews and providing most valuable comments.

   Carlos Pignataro would like to acknowledge his lifetime friend Martin
   Rigueiro, with deep gratutide and esteem, for sharing his contagious
   passion for engineering and sciences, and for selflessly teaching so
   many lessons.

14.  Contributing Authors

   Nagendra Kumar
   Cisco Systems, Inc.

   Email: naikumar@cisco.com

15.  References

15.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <http://www.rfc-editor.org/info/rfc2119>.




Akiya, et al.             Expires March 9, 2017                [Page 20]


Internet-Draft            LSP Ping over Entropy           September 2016


   [RFC4379]  Kompella, K. and G. Swallow, "Detecting Multi-Protocol
              Label Switched (MPLS) Data Plane Failures", RFC 4379,
              DOI 10.17487/RFC4379, February 2006,
              <http://www.rfc-editor.org/info/rfc4379>.

   [RFC6424]  Bahadur, N., Kompella, K., and G. Swallow, "Mechanism for
              Performing Label Switched Path Ping (LSP Ping) over MPLS
              Tunnels", RFC 6424, DOI 10.17487/RFC6424, November 2011,
              <http://www.rfc-editor.org/info/rfc6424>.

   [RFC6790]  Kompella, K., Drake, J., Amante, S., Henderickx, W., and
              L. Yong, "The Use of Entropy Labels in MPLS Forwarding",
              RFC 6790, DOI 10.17487/RFC6790, November 2012,
              <http://www.rfc-editor.org/info/rfc6790>.

   [RFC7537]  Decraene, B., Akiya, N., Pignataro, C., Andersson, L., and
              S. Aldrin, "IANA Registries for LSP Ping Code Points",
              RFC 7537, DOI 10.17487/RFC7537, May 2015,
              <http://www.rfc-editor.org/info/rfc7537>.

15.2.  Informative References

   [IANA-MPLS-LSP-PING]
              IANA, "Multi-Protocol Label Switching (MPLS) Label
              Switched Paths (LSPs) Ping Parameters",
              <http://www.iana.org/assignments/mpls-lsp-ping-parameters/
              mpls-lsp-ping-parameters.xhtml>.

   [RFC6391]  Bryant, S., Ed., Filsfils, C., Drafz, U., Kompella, V.,
              Regan, J., and S. Amante, "Flow-Aware Transport of
              Pseudowires over an MPLS Packet Switched Network",
              RFC 6391, DOI 10.17487/RFC6391, November 2011,
              <http://www.rfc-editor.org/info/rfc6391>.

   [RFC7325]  Villamizar, C., Ed., Kompella, K., Amante, S., Malis, A.,
              and C. Pignataro, "MPLS Forwarding Compliance and
              Performance Requirements", RFC 7325, DOI 10.17487/RFC7325,
              August 2014, <http://www.rfc-editor.org/info/rfc7325>.

Authors' Addresses

   Nobo Akiya
   Big Switch Networks

   Email: nobo.akiya.dev@gmail.com






Akiya, et al.             Expires March 9, 2017                [Page 21]


Internet-Draft            LSP Ping over Entropy           September 2016


   George Swallow
   Cisco Systems, Inc.

   Email: swallow@cisco.com


   Carlos Pignataro
   Cisco Systems, Inc.

   Email: cpignata@cisco.com


   Andrew G. Malis
   Huawei Technologies

   Email: agmalis@gmail.com


   Sam Aldrin
   Google

   Email: aldrin.ietf@gmail.com





























Akiya, et al.             Expires March 9, 2017                [Page 22]


Html markup produced by rfcmarkup 1.123, available from https://tools.ietf.org/tools/rfcmarkup/