[Docs] [txt|pdf|xml|html] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]
Versions: (draft-bierman-netconf-with-defaults)
00 01 02 03 04 05 06 07 08 09 10 11
12 13 14 RFC 6243
NETCONF A. Bierman
Internet-Draft Brocade
Intended status: Standards Track B. Lengyel
Expires: May 15, 2011 Ericsson
November 11, 2010
With-defaults capability for NETCONF
draft-ietf-netconf-with-defaults-14
Abstract
The NETCONF protocol defines ways to read and edit configuration data
from a NETCONF server. In some cases, part of this data may not be
set by the NETCONF client, but rather a default value known to the
server is used instead. In many situations the NETCONF client has a
priori knowledge about default data, so the NETCONF server does not
need to save it in a NETCONF configuration datastore or send it to
the client in a retrieval operation reply. In other situations the
NETCONF client will need this data from the server. Not all server
implementations treat this default data the same way. This document
defines a capability-based extension to the NETCONF protocol that
allows the NETCONF client to identify how defaults are processed by
the server, and also defines new mechanisms for client control of
server processing of default data.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on May 15, 2011.
Copyright Notice
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
Bierman & Lengyel Expires May 15, 2011 [Page 1]
Internet-Draft with-defaults November 2010
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 4
1.2. Defaults Handling Behavior . . . . . . . . . . . . . . . . 5
1.3. Client Controlled Retrieval of Default Data . . . . . . . 5
2. Defaults Handling Basic Modes . . . . . . . . . . . . . . . . 6
2.1. 'report-all' Basic Mode . . . . . . . . . . . . . . . . . 6
2.1.1. 'report-all' Basic Mode Retrieval . . . . . . . . . . 7
2.1.2. 'report-all' <with-defaults> Retrieval . . . . . . . . 7
2.1.3. 'report-all' <edit-config> and <copy-config>
Behavior . . . . . . . . . . . . . . . . . . . . . . . 7
2.2. 'trim' Basic Mode . . . . . . . . . . . . . . . . . . . . 7
2.2.1. 'trim' Basic Mode Retrieval . . . . . . . . . . . . . 7
2.2.2. 'trim' <with-defaults> Retrieval . . . . . . . . . . . 7
2.2.3. 'trim' <edit-config> and <copy-config> Behavior . . . 8
2.3. 'explicit' Basic Mode . . . . . . . . . . . . . . . . . . 8
2.3.1. 'explicit' Basic Mode Retrieval . . . . . . . . . . . 8
2.3.2. 'explicit' <with-defaults> Retrieval . . . . . . . . . 8
2.3.3. 'explicit' <edit-config> and <copy-config> Behavior . 8
3. Retrieval of Default Data . . . . . . . . . . . . . . . . . . 9
3.1. 'report-all' Retrieval Mode . . . . . . . . . . . . . . . 9
3.2. 'trim' Retrieval Mode . . . . . . . . . . . . . . . . . . 9
3.3. 'explicit' Retrieval Mode . . . . . . . . . . . . . . . . 9
3.4. 'report-all-tagged' Retrieval Mode . . . . . . . . . . . . 10
4. With-defaults Capability . . . . . . . . . . . . . . . . . . . 10
4.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2. Dependencies . . . . . . . . . . . . . . . . . . . . . . . 11
4.3. Capability Identifier . . . . . . . . . . . . . . . . . . 11
4.4. New Operations . . . . . . . . . . . . . . . . . . . . . . 11
4.5. Modifications to Existing Operations . . . . . . . . . . . 11
4.5.1. <get>, <get-config>, and <copy-config> Operations . . 11
4.5.2. <edit-config> Operation . . . . . . . . . . . . . . . 13
4.5.3. Other Operations . . . . . . . . . . . . . . . . . . . 13
4.6. Interactions with Other Capabilities . . . . . . . . . . . 14
5. YANG Module for the <with-defaults> Parameter . . . . . . . . 14
6. XSD for the 'default' Attribute . . . . . . . . . . . . . . . 17
Bierman & Lengyel Expires May 15, 2011 [Page 2]
Internet-Draft with-defaults November 2010
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 19
8. Security Considerations . . . . . . . . . . . . . . . . . . . 19
9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 19
10. Normative References . . . . . . . . . . . . . . . . . . . . . 20
Appendix A. Usage Examples . . . . . . . . . . . . . . . . . . . 20
A.1. Example YANG Module . . . . . . . . . . . . . . . . . . . 20
A.2. Example Data Set . . . . . . . . . . . . . . . . . . . . . 22
A.3. Protocol Operation Examples . . . . . . . . . . . . . . . 23
A.3.1. <with-defaults> = 'report-all' . . . . . . . . . . . . 23
A.3.2. <with-defaults> = 'report-all-tagged' . . . . . . . . 24
A.3.3. <with-defaults> = 'trim' . . . . . . . . . . . . . . . 27
A.3.4. <with-defaults> = 'explicit' . . . . . . . . . . . . . 28
Appendix B. Change Log . . . . . . . . . . . . . . . . . . . . . 29
B.1. 13-14 . . . . . . . . . . . . . . . . . . . . . . . . . . 29
B.2. 12-13 . . . . . . . . . . . . . . . . . . . . . . . . . . 29
B.3. 11-12 . . . . . . . . . . . . . . . . . . . . . . . . . . 29
B.4. 10-11 . . . . . . . . . . . . . . . . . . . . . . . . . . 29
B.5. 09-10 . . . . . . . . . . . . . . . . . . . . . . . . . . 29
B.6. 08-09 . . . . . . . . . . . . . . . . . . . . . . . . . . 29
B.7. 07-08 . . . . . . . . . . . . . . . . . . . . . . . . . . 30
B.8. 06-07 . . . . . . . . . . . . . . . . . . . . . . . . . . 30
B.9. 05-06 . . . . . . . . . . . . . . . . . . . . . . . . . . 30
B.10. 04-05 . . . . . . . . . . . . . . . . . . . . . . . . . . 31
B.11. 03-04 . . . . . . . . . . . . . . . . . . . . . . . . . . 31
B.12. 02-03 . . . . . . . . . . . . . . . . . . . . . . . . . . 31
B.13. 01-02 . . . . . . . . . . . . . . . . . . . . . . . . . . 32
B.14. 00-01 . . . . . . . . . . . . . . . . . . . . . . . . . . 32
B.15. -00 . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 32
Bierman & Lengyel Expires May 15, 2011 [Page 3]
Internet-Draft with-defaults November 2010
1. Introduction
The NETCONF protocol [I-D.ietf-netconf-4741bis] defines ways to read
configuration and state data from a NETCONF server. Part of the
configuration data may not be set by the NETCONF client, but rather
by a default value from the data model. In many situations the
NETCONF client has a priori knowledge about default data, so the
NETCONF server does not need to send it to the client. A priori
knowledge can be obtained, e.g., a document formally describing the
data models supported by the NETCONF server.
It can be important for a client to know exactly how a server
implementation will handle default data. There are subtle
differences in some protocol operations where the defaults handling
behavior of the server will affect the outcome of the operation.
1.1. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
Data model schema: A document or set of documents describing the
data models supported by the NETCONF server.
Management Application: A computer program running outside the
NETCONF server that configures or supervises the NETCONF server.
A management application can reach the device e.g. via NETCONF,
command line interface (CLI) or Simple Network Management Protocol
(SNMP).
Schema default data: Data specified in the data model schema as
default, that is set or used by the device whenever the NETCONF
client or other management application/user does not provide a
specific value for the relevant data node. Schema default data
may or may not be stored as part of a configuration datastore,
depending on the basic mode used by a particular server.
Default data: Conceptual data containing a default value. Default
data is not kept in a datastore. Not all servers use the same
criteria to decide if a data node is actually instantiated in a
datastore. If a data node is not present in a datastore, and a
schema default definition is in use by the server instead, then it
is considered to be a default data node.
Default value: A default value is a value for a data node instance
that is conceptually in use by the server, when the data node
instance does not exist.
Bierman & Lengyel Expires May 15, 2011 [Page 4]
Internet-Draft with-defaults November 2010
Explicitly set data: Data that is set to any value by a NETCONF
client or other management application by the way of an explicit
management operation, including any data model schema default
value. Any value set by the NETCONF server which is not the
schema defined default value is also considered explicitly set
data.
<with-defaults> retrieval: Refers to a protocol operation which
includes the <with-default> parameter to control the handling of
default data.
:with-defaults: The shorthand notation for the with-defaults
capability identifier.
The following terms are defined in [I-D.ietf-netconf-4741bis]:
o client
o datastore
o operation
o server
The following term is defined in [RFC6020]:
o data node
1.2. Defaults Handling Behavior
The defaults handling behavior used by a server will impact NETCONF
protocol operations in two ways:
1. Data retrieval: A server is normally allowed to exclude data
nodes which it considers to contain the default value. The
actual nodes omitted depends on the defaults handling behavior
used by the server.
2. Create and delete operations: The <edit-config> 'operation'
attribute can be used to create and/or delete specific data
nodes. These operations depend on whether the target node
currently exists or not. The server's defaults handling behavior
will determine whether the requested node currently exists in the
configuration datastore or not.
1.3. Client Controlled Retrieval of Default Data
A networking device may have a large number of default values. Often
the default values are specifically defined with a reasonable value,
documented and well-known, so that the management user does not need
to handle them. For these reasons it is quite common for networking
devices to suppress the output of parameters having the default
value.
Bierman & Lengyel Expires May 15, 2011 [Page 5]
Internet-Draft with-defaults November 2010
However, there are use-cases when a NETCONF client will need the
default data from the server:
o The management application often needs a single, definitive and
complete set of configuration values that determine how the
networking device works.
o Documentation about default values can be unreliable or
unavailable.
o Some management applications might not have the capabilities to
correctly parse and interpret formal data models.
o Human users might want to understand the received data without
consultation of the documentation.
In all these cases, the NETCONF client will need a mechanism to
retrieve default data from a NETCONF server.
This document defines a NETCONF protocol capability to identify the
server defaults handling behavior, an XML attribute to identify
default data, and a YANG module extension to the NETCONF protocol
that allows the NETCONF client to control whether default data is
returned by the server.
2. Defaults Handling Basic Modes
Not all server implementations treat default data in the same way.
Instead of forcing a single implementation strategy, this document
allows a server to advertise a particular style of defaults handling,
and the client can adjust accordingly.
NETCONF servers report default data in different ways. This document
specifies three standard defaults handling basic modes that a server
implementor may choose from:
o report-all
o trim
o explicit
A server MUST select one of the three basic modes defined in this
section for handling default data.
2.1. 'report-all' Basic Mode
A server which uses the 'report-all' basic mode does not consider any
data node to be default data, even schema default data.
Bierman & Lengyel Expires May 15, 2011 [Page 6]
Internet-Draft with-defaults November 2010
2.1.1. 'report-all' Basic Mode Retrieval
When data is retrieved from a server using the 'report-all' basic
mode, and the <with-defaults> parameter is not present, all data
nodes MUST be reported.
2.1.2. 'report-all' <with-defaults> Retrieval
If the 'report-all' basic mode is used by the server, then the server
MUST support the <with-defaults> parameter with a value equal to
'report-all', as specified in Section 3.1.
2.1.3. 'report-all' <edit-config> and <copy-config> Behavior
The server MUST consider every data node to exist, even those
containing a schema default value. A valid 'create' operation
attribute for a data node that contains its schema default value MUST
fail with a 'data-exists' error-tag. A valid 'delete' operation
attribute for a data node that contains its schema default value MUST
succeed, even though the data node is immediately replaced by the
server with the default value.
A server which uses the 'report-all' basic-mode has no concept of a
default node, so the 'report-all-tagged' <with-defaults> retrieval
mode is not relevant. There will never be any tagged nodes, since
there are no nodes which are omitted in a basic-mode retrieval
operation. If the 'default' attribute is present in any
configuration data, the server MUST return an <rpc-error> response
with an 'unknown-attribute' error-tag.
2.2. 'trim' Basic Mode
A server which uses the 'trim' basic mode MUST consider any data node
set to its schema default value to be default data.
2.2.1. 'trim' Basic Mode Retrieval
When data is retrieved from a server using the 'trim' basic mode, and
the <with-defaults> parameter is not present, data nodes MUST NOT be
reported if they contain the schema default value. Non-configuration
data nodes containing the schema default value MUST NOT be reported.
2.2.2. 'trim' <with-defaults> Retrieval
If the 'trim' basic mode is used by the server, then the server MUST
support the <with-defaults> parameter with a value equal to 'trim',
as specified in Section 3.2.
Bierman & Lengyel Expires May 15, 2011 [Page 7]
Internet-Draft with-defaults November 2010
2.2.3. 'trim' <edit-config> and <copy-config> Behavior
The server MUST consider any data node that does not contain its
schema default value to exist. A valid 'create' operation attribute
for a data node that has a schema default value defined MUST succeed.
A valid 'delete' operation attribute for a missing data node that has
a schema default value MUST fail. The server MUST return an <rpc-
error> response with a 'data-missing' error-tag.
If a client sets a data node to its schema default value, using any
valid operation, it MUST succeed, although the data node MUST NOT be
saved in the NETCONF configuration datastore. This has the same
effect as removing the data node and treating it as default data.
If the server supports the 'report-all-tagged' value for the <with-
defaults> parameter, then the 'default' attribute MUST be accepted in
configuration input, as described in Section 4.5.1 and Section 4.5.2.
2.3. 'explicit' Basic Mode
A server which uses the 'explicit' basic mode MUST consider any data
node that is not explicitly set data to be default data.
2.3.1. 'explicit' Basic Mode Retrieval
When data is retrieved from a server using the 'explicit' basic mode,
and the <with-defaults> parameter is not present, data nodes MUST be
reported if explicitly set by the client, even if they contain the
schema default value. Non-configuration data nodes containing the
schema default value MUST be reported.
2.3.2. 'explicit' <with-defaults> Retrieval
If the 'explicit' basic mode is used by the server, the server MUST
support the <with-defaults> parameter with a value equal to
'explicit', as specified in Section 3.3.
2.3.3. 'explicit' <edit-config> and <copy-config> Behavior
The server considers any data node that is explicitly set data to
exist. A valid 'create' operation attribute for a data node that has
been set by a client to its schema default value MUST fail with a
'data-exists' error-tag. A valid 'create' operation attribute for a
data node that has been set by the server to its schema default value
MUST succeed. A valid 'delete' operation attribute for a data node
that has been set by a client to its schema default value MUST
succeed. A valid 'delete' operation attribute for a data node that
has been set by the server to its schema default value MUST fail with
Bierman & Lengyel Expires May 15, 2011 [Page 8]
Internet-Draft with-defaults November 2010
a 'data-missing' error-tag.
If the server supports the 'report-all-tagged' retrieval mode in its
:with-defaults capability, then the 'default' attribute MUST be
accepted in configuration input. If all NETCONF <edit-config> or
<copy-config> parameters are valid, then the server will treat a
tagged data node (i.e., the 'default' attribute set to 'true' or '1')
as a request to return that node to default data. If this request is
valid within the context of the requested NETCONF operation, then the
data node is removed and returned to its default value. The data
node within the NETCONF message MUST contain a value in this case,
which MUST be equal to the schema default value. If not, the server
MUST return an <rpc-error> response with a 'invalid-value' error-tag.
3. Retrieval of Default Data
This document defines a new parameter, called <with-defaults>, which
can be added to specific NETCONF operation request messages to
control how retrieval of default data is treated by the server.
A server which implements this specification MUST accept the <with-
defaults> parameter containing the enumeration for any of the
defaults handling modes it supports. The <with-defaults> parameter
contains one of the four enumerations defined in this section.
3.1. 'report-all' Retrieval Mode
When data is retrieved with a <with-defaults> parameter equal to
'report-all', all data nodes MUST be reported, including any data
nodes considered to be default data by the server.
3.2. 'trim' Retrieval Mode
When data is retrieved with a <with-defaults> parameter equal to
'trim', data nodes MUST NOT be reported if they contain the schema
default value. Non-configuration data nodes containing the schema
default value MUST NOT be reported.
3.3. 'explicit' Retrieval Mode
When data is retrieved with a <with-defaults> parameter equal to
'explicit', a data node which was set by a client to its schema
default value MUST be reported. A conceptual data node which would
be set by the server to the schema default value MUST NOT be
reported. Non-configuration data nodes containing the schema default
value MUST be reported.
Bierman & Lengyel Expires May 15, 2011 [Page 9]
Internet-Draft with-defaults November 2010
3.4. 'report-all-tagged' Retrieval Mode
In addition to the basic modes, a special variant of the 'report-all'
basic mode is available called 'report-all-tagged'. This mode MUST
be supported on a server if the 'also-supported' parameter in the
:with-defaults capability contains the 'report-all-tagged' option.
Refer to Section 4 for encoding details for this capability.
In this mode the server returns all data nodes, just like the
'report-all' mode, except a data node that is considered by the
server to contain default data will include an XML attribute to
indicate this condition. This is useful for an application to
determine which nodes are considered to contain default data by the
server, within a single retrieval operation.
A server which supports 'report-all-tagged' MUST also accept the
'default' XML attribute within configuration input to the <edit-
config> or <copy-config> operations. Refer to Section 6 for XML
encoding details of the 'default' XML attribute.
4. With-defaults Capability
4.1. Overview
The :with-defaults capability indicates which defaults handling basic
mode is supported by the server. It may also indicate support for
additional defaults retrieval modes. These retrieval modes allow a
NETCONF client to control whether default data is returned by the
server. The capability affects both configuration and state data
(while acknowledging that the usage of default values for state data
is less prevalent). Sending of default data is controlled for each
individual operation separately.
A NETCONF server implementing the :with-defaults capability:
o MUST indicate its basic mode behavior by including the 'basic-
mode' parameter in the capability URI, as defined in Section 4.3.
o MUST support the YANG module defined in Section 5 for the defaults
handling mode indicated by the 'basic-mode' parameter.
o SHOULD support the YANG module in Section 5 for the defaults
handling mode identified by the 'report-all' or 'report-all-
tagged' enumeration value.
o If the 'report-all-tagged' defaults handling mode is supported,
then the 'default' attribute MUST be supported.
o MAY support the YANG module in Section 5 for additional defaults
handling modes.
Bierman & Lengyel Expires May 15, 2011 [Page 10]
Internet-Draft with-defaults November 2010
4.2. Dependencies
None
4.3. Capability Identifier
urn:ietf:params:netconf:capability:with-defaults:1.0
The identifier MUST have a parameter: "basic-mode". This indicates
how the server will treat default data, as defined in Section 2. The
allowed values of this parameter are 'report-all', 'trim', and
'explicit', as defined in Section 2.
The identifier MAY have another parameter: "also-supported". This
parameter indicates which additional enumeration values (besides the
basic-mode enumeration), the server will accept for the <with-
defaults> parameter in Section 5. The value of the parameter is a
comma separated list of one or more modes that are supported beside
the mode indicated in the 'basic-mode' parameter. Possible modes are
'report-all', 'report-all-tagged', 'trim', and 'explicit', as defined
in Section 3.
Note that this protocol capability URI is separate from the YANG
module capability URI for the YANG module in Section 5. A server
which implements this module MUST also advertise a YANG module
capability URI according to the rules specified in [RFC6020].
Examples:
urn:ietf:params:netconf:capability:with-defaults:1.0?basic-
mode=explicit
urn:ietf:params:netconf:capability:with-defaults:1.0?basic-
mode=explicit&also-supported=report-all,report-all-tagged
4.4. New Operations
None
4.5. Modifications to Existing Operations
4.5.1. <get>, <get-config>, and <copy-config> Operations
A new <with-defaults> XML element is added to the input for the
<get>, <get-config> and <copy-config> operations. If the <with-
defaults> element is present, it controls the reporting of default
data. The server MUST return default data in the NETCONF <rpc-reply>
messages according to the value of this element, if the server
Bierman & Lengyel Expires May 15, 2011 [Page 11]
Internet-Draft with-defaults November 2010
supports the specified retrieval mode.
This parameter only controls these specified retrieval operations,
and does not impact any other operations or the non-volatile storage
of configuration data.
The <with-defaults> element is defined in the XML namespace for the
ietf-netconf-with-defaults.yang module in Section 5, not the XML
namespace for the <get>, <get-config> and <copy-config> operations.
Allowed values of the with-defaults element are taken from the 'with-
defaults-type' typedef in Section 5. The allowed values for a
particular server are restricted to the values that the server
indicates it supports within the :with-defaults capability, in the
'basic-mode' and 'also-supported' parameters.
If an unsupported value is used, the NETCONF server MUST return an
<rpc-error> response with an 'invalid-value' error-tag.
If the <with-defaults> element is not present, the server MUST follow
its basic mode behavior as indicated by the :with-defaults capability
identifier's 'basic-mode' parameter, defined in Section 4.3.
The <get> and <get-config> operations support a separate filtering
mechanism, using the <filter> parameter. The defaults filtering is
conceptually done before the <filter> parameter is processed. For
example, if the <with-defaults> parameter is equal to 'report-all',
then the <filter> parameter is conceptually applied to all data nodes
and all default data.
The <copy-config> operation is only affected by the <with-defaults>
parameter if the target of the operation is specified with the <url>
parameter. If the target is a NETCONF configuration datastore (i.e.,
running, candidate or startup), the <with-defaults> parameter has no
effect. The server MUST use its basic mode when copying data to a
NETCONF configuration datastore. If the <with-defaults> parameter is
present in this case, it MUST be silently ignored by the server.
If the server supports the 'report-all-tagged' mode, then the
'default' attribute defined in Section 6 also impacts the <copy-
config> operation. If the 'default' attribute is present and set to
'true' or '1', then the server MUST treat the new data node as a
request to return that node to its default value (i.e., remove it
from the configuration datastore). The data node within the NETCONF
message MUST contain a value in this case, which MUST be equal to the
schema default value. If not, the server MUST return an <rpc-error>
response with a 'invalid-value' error-tag.
Bierman & Lengyel Expires May 15, 2011 [Page 12]
Internet-Draft with-defaults November 2010
4.5.2. <edit-config> Operation
The <edit-config> operation has several editing modes. The 'create'
and 'delete' editing operations are affected by the defaults handling
basic mode. The other enumeration values for the NETCONF operation
attribute are not affected.
If the operation attribute contains the value 'create', and the data
node already exists in the target configuration datastore, then the
server MUST return an <rpc-error> response with a 'invalid-value'
error-tag.
If the client sets a data node to its schema default value, the
server MUST accept the request if it is valid. The server MUST keep
or discard the new value based on its defaults handling basic mode.
For the 'trim' basic mode, all schema default values are discarded,
otherwise a client-provided schema default value is saved in a
NETCONF configuration datastore.
If the server supports the 'report-all-tagged' mode, then the
'default' attribute defined in Section 6 also impacts the <edit-
config> operation. If the 'default' attribute is present and set to
'true' or '1', then the server MUST treat the new data node as a
request to return that node to its default value (i.e., remove it
from the configuration datastore). The data node within the NETCONF
message MUST contain a value in this case, which MUST be equal to the
schema default value. If not, the server MUST return an <rpc-error>
response with a 'invalid-value' error-tag.
If the 'default' attribute is present, then the effective operation
for the target data node MUST be 'create', 'merge' or 'replace'. If
not, then the server MUST return an <rpc-error> response with an
'invalid-value' error-tag. For example, if 'create' is the effective
operation, then the create request must be valid on its own (e.g.,
current data node MUST NOT exist). The procedure for determining the
effective operation is defined in [I-D.ietf-netconf-4741bis]. It is
derived from the 'default-operation' parameter and/or any operation
attributes that are present in the data node or any of its ancestor
nodes, within the <edit-config> request.
4.5.3. Other Operations
Other operations that return configuration data SHOULD also handle
default data according to the rules set in this document, and
explicitly state this in their documentation. If this is not
specified in the document defining the respective operation, the
default handling rules described herein do not affect these
operations.
Bierman & Lengyel Expires May 15, 2011 [Page 13]
Internet-Draft with-defaults November 2010
4.6. Interactions with Other Capabilities
None
5. YANG Module for the <with-defaults> Parameter
The following YANG module defines the addition of the with-defaults
element to the <get>, <get-config>, and <copy-config> operations.
The YANG language is defined in [RFC6020]. The above operations are
defined in YANG in [I-D.ietf-netconf-4741bis]. Every NETCONF server
which supports the :with-defaults capability MUST implement this YANG
module.
<CODE BEGINS> file="ietf-netconf-with-defaults@2010-11-11.yang"
module ietf-netconf-with-defaults {
namespace "urn:ietf:params:xml:ns:yang:ietf-netconf-with-defaults";
prefix ncwd;
import ietf-netconf { prefix nc; }
organization
"IETF NETCONF (Network Configuration Protocol) Working Group";
contact
"WG Web: <http://tools.ietf.org/wg/netconf/>
WG List: <mailto:netconf@ietf.org>
WG Chair: Bert Wijnen
<mailto:bertietf@bwijnen.net>
WG Chair: Mehmet Ersue
<mailto:mehmet.ersue@nsn.com>
Editor: Andy Bierman
<mailto:andy.bierman@brocade.com>
Editor: Balazs Lengyel
<mailto:balazs.lengyel@ericsson.com>";
description
"This module defines an extension to the NETCONF protocol
that allows the NETCONF client to control how default
Bierman & Lengyel Expires May 15, 2011 [Page 14]
Internet-Draft with-defaults November 2010
values are handled by the server in particular NETCONF operations.
Copyright (c) 2010 IETF Trust and the persons identified as
the document authors. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; see
the RFC itself for full legal notices.";
// RFC Ed.: replace XXXX with actual RFC number and remove this note
// RFC Ed.: remove this note
// Note: extracted from draft-ietf-netmod-with-defaults-14.txt
revision 2010-11-11 {
description
"Initial version.";
reference
"RFC XXXX: With-defaults capability for NETCONF";
}
// RFC Ed.: replace XXXX with actual
// RFC number and remove this note
typedef with-defaults-mode {
description
"Possible modes to report default data.";
reference
"RFC XXXX; section 3.";
// RFC Ed.: replace XXXX with actual
// RFC number and remove this note
type enumeration {
enum report-all {
description
"All default data is reported.";
reference
"RFC XXXX; section 3.1";
// RFC Ed.: replace XXXX with actual
// RFC number and remove this note
}
enum report-all-tagged {
description
Bierman & Lengyel Expires May 15, 2011 [Page 15]
Internet-Draft with-defaults November 2010
"All default data is reported.
Any nodes considered to be default data
will contain a 'default' XML attribute,
set to 'true' or '1'.";
reference
"RFC XXXX; section 3.4";
// RFC Ed.: replace XXXX with actual
// RFC number and remove this note
}
enum trim {
description
"Values are not reported if they contain the default.";
reference
"RFC XXXX; section 3.2";
// RFC Ed.: replace XXXX with actual
// RFC number and remove this note
}
enum explicit {
description
"Report values that contain the definition of
explicitly set data.";
reference
"RFC XXXX; section 3.3";
// RFC Ed.: replace XXXX with actual
// RFC number and remove this note
}
}
}
grouping with-defaults-parameters {
description
"Contains the <with-defaults> parameter for control
of defaults in NETCONF retrieval operations.";
leaf with-defaults {
description
"The explicit defaults processing mode requested.";
reference
"RFC XXXX; section 4.6.1";
// RFC Ed.: replace XXXX with actual
// RFC number and remove this note
type with-defaults-mode;
}
}
// extending the get-config operation
Bierman & Lengyel Expires May 15, 2011 [Page 16]
Internet-Draft with-defaults November 2010
augment /nc:get-config/nc:input {
description
"Adds the <with-defaults> parameter to the
input of the NETCONF <get-config> operation.";
reference
"RFC XXXX; section 4.6.1";
// RFC Ed.: replace XXXX with actual
// RFC number and remove this note
uses with-defaults-parameters;
}
// extending the get operation
augment /nc:get/nc:input {
description
"Adds the <with-defaults> parameter to
the input of the NETCONF <get> operation.";
reference
"RFC XXXX; section 4.6.1";
// RFC Ed.: replace XXXX with actual
// RFC number and remove this note
uses with-defaults-parameters;
}
// extending the copy-config operation
augment /nc:copy-config/nc:input {
description
"Adds the <with-defaults> parameter to
the input of the NETCONF <copy-config> operation.";
reference
"RFC XXXX; section 4.6.1";
// RFC Ed.: replace XXXX with actual
// RFC number and remove this note
uses with-defaults-parameters;
}
}
<CODE ENDS>
6. XSD for the 'default' Attribute
The following XML Schema document [W3C.REC-xml-20081126] defines the
'default' attribute, described within this document. This XSD is
Bierman & Lengyel Expires May 15, 2011 [Page 17]
Internet-Draft with-defaults November 2010
only relevant if the server supports the 'report-all-tagged' defaults
retrieval mode.
The 'default' attribute uses the XSD data type 'boolean'. In
accordance with Section 3.2.2.1 of XML Schema Part 2: Datatypes, the
allowable lexical representations for the xs:boolean datatype are the
strings "0" and "false" for the concept of false and the strings "1"
and "true" for the concept of true. Implementations MUST support
both styles of lexical representation.
<CODE BEGINS> file="defaults.xsd"
<?xml version="1.0" encoding="UTF-8"?>
<xs:schema xmlns:xs="http://www.w3.org/2001/XMLSchema"
xmlns="urn:ietf:params:xml:ns:netconf:default:1.0"
targetNamespace="urn:ietf:params:xml:ns:netconf:default:1.0"
elementFormDefault="qualified"
attributeFormDefault="unqualified"
xml:lang="en">
<xs:annotation>
<xs:documentation>
This schema defines the syntax for the 'default' attribute
described within this document.
</xs:documentation>
</xs:annotation>
<!--
default attribute
-->
<xs:attribute name="default" type="xs:boolean" default="false">
<xs:annotation>
<xs:documentation>
This attribute indicates whether the data node represented
by the XML element containing this attribute is considered
by the server to be default data. If set to 'true' or '1' then
the data node is default data. If 'false' or '0', then the
data node is not default data.
</xs:documentation>
</xs:annotation>
</xs:attribute>
</xs:schema>
<CODE ENDS>
Bierman & Lengyel Expires May 15, 2011 [Page 18]
Internet-Draft with-defaults November 2010
7. IANA Considerations
This document registers the following capability identifier URN in
the 'Network Configuration Protocol Capability URNs registry':
urn:ietf:params:netconf:capability:with-defaults:1.0
Note that the capability URN is compliant to
[I-D.ietf-netconf-4741bis] section 10.3.
This document registers two XML namespace URNs in the 'IETF XML
registry', following the format defined in [RFC3688].
URI: urn:ietf:params:xml:ns:netconf:default:1.0
URI: urn:ietf:params:xml:ns:yang:ietf-netconf-with-defaults
Registrant Contact: The NETCONF WG of the IETF.
XML: N/A, the requested URIs are XML namespaces.
This document registers one module name in the 'YANG Module Names'
registry, defined in [RFC6020] .
name: ietf-netconf-with-defaults
prefix: ncwd
namespace: urn:ietf:params:xml:ns:yang:ietf-netconf-with-defaults
RFC: XXXX // RFC Ed.: replace XXXX and remove this comment
8. Security Considerations
This document defines an extension to existing NETCONF protocol
operations. It does not introduce any new or increased security
risks into the management system.
The 'with-defaults' capability gives clients control over the
retrieval of default data from a NETCONF datastore. The security
consideration of [I-D.ietf-netconf-4741bis] apply to this document as
well.
9. Acknowledgements
Thanks to Martin Bjorklund, Sharon Chisholm, Phil Shafer, Juergen
Schoenwaelder, Kent Watsen, Washam Fan and many other members of the
NETCONF WG for providing important input to this document.
Bierman & Lengyel Expires May 15, 2011 [Page 19]
Internet-Draft with-defaults November 2010
10. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
January 2004.
[RFC6020] Bjorklund, M., "YANG - A Data Modeling Language for the
Network Configuration Protocol (NETCONF)", RFC 6020,
October 2010.
[I-D.ietf-netconf-4741bis]
Enns, R., Bjorklund, M., Schoenwaelder, J., and A.
Bierman, "Network Configuration Protocol (NETCONF)",
draft-ietf-netconf-4741bis-06 (work in progress),
October 2010.
[W3C.REC-xml-20081126]
Maler, E., Yergeau, F., Sperberg-McQueen, C., Paoli, J.,
and T. Bray, "Extensible Markup Language (XML) 1.0 (Fifth
Edition)", World Wide Web Consortium Recommendation REC-
xml-20081126, November 2008,
<http://www.w3.org/TR/2008/REC-xml-20081126>.
[W3C.REC-xmlschema-0-20041028]
Walmsley, P. and D. Fallside, "XML Schema Part 0: Primer
Second Edition", World Wide Web Consortium
Recommendation REC-xmlschema-0-20041028, October 2004,
<http://www.w3.org/TR/2004/REC-xmlschema-0-20041028>.
Appendix A. Usage Examples
A.1. Example YANG Module
The following YANG module defines an example interfaces table to
demonstrate how the <with-defaults> parameter behaves for a specific
data model.
Note that this is not a real module, and implementation of this
module is not required for conformance to the :with-defaults
capability, defined in Section 4. This module is not to be
registered with IANA, and is not considered to be a code component.
It is intentionally very terse, and includes few descriptive
statements.
Bierman & Lengyel Expires May 15, 2011 [Page 20]
Internet-Draft with-defaults November 2010
module example {
namespace "http://example.com/ns/interfaces";
prefix exam;
typedef status-type {
description "Interface status";
type enumeration {
enum ok;
enum 'waking up';
enum 'not feeling so good';
enum 'better check it out';
enum 'better call for help';
}
default ok;
}
container interfaces {
description "Example interfaces group";
list interface {
description "Example interface entry";
key name;
leaf name {
description
"The administrative name of the interface.
This is an identifier which is only unique
within the scope of this list, and only
within a specific server.";
type string {
length "1 .. max";
}
}
leaf mtu {
description
"The maximum transmission unit (MTU) value assigned to
this interface.";
type uint32;
default 1500;
}
leaf status {
description
"The current status of this interface.";
type status-type;
Bierman & Lengyel Expires May 15, 2011 [Page 21]
Internet-Draft with-defaults November 2010
config false;
}
}
}
}
A.2. Example Data Set
The following data element shows the conceptual contents of the
example server for the protocol operation examples in the next
section. This includes all the configuration data nodes, non-
configuration data nodes, and default leafs.
<data xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<interfaces xmlns="http://example.com/ns/interfaces">
<interface>
<name>eth0</name>
<mtu>8192</mtu>
<status>up</status>
</interface>
<interface>
<name>eth1</name>
<mtu>1500</mtu>
<status>up</status>
</interface>
<interface>
<name>eth2</name>
<mtu>9000</mtu>
<status>not feeling so good</status>
</interface>
<interface>
<name>eth3</name>
<mtu>1500</mtu>
<status>waking up</status>
</interface>
</interfaces>
</data>
In this example, the 'mtu' field for each interface entry is set in
the following manner:
Bierman & Lengyel Expires May 15, 2011 [Page 22]
Internet-Draft with-defaults November 2010
+--------------+--------------+--------------+
| name | set by | mtu |
+--------------+--------------+--------------+
| eth0 | client | 8192 |
| eth1 | server | 1500 |
| eth2 | client | 9000 |
| eth3 | client | 1500 |
+--------------+--------------+--------------+
A.3. Protocol Operation Examples
The following examples shows some <get> operations using the 'with-
defaults' element. The data model used for these examples is defined
in Appendix A.1.
The client is retrieving all the data nodes within the 'interfaces'
object, filtered with the <with-defaults> parameter.
A.3.1. <with-defaults> = 'report-all'
The behavior of the <with-defaults> parameter handling for the value
'report-all' is demonstrated in this example.
Bierman & Lengyel Expires May 15, 2011 [Page 23]
Internet-Draft with-defaults November 2010
<rpc message-id="101"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<get>
<filter type="subtree">
<interfaces xmlns="http://example.com/ns/interfaces"/>
</filter>
<with-defaults
xmlns="urn:ietf:params:xml:ns:yang:ietf-netconf-with-defaults">
report-all
</with-defaults>
</get>
</rpc>
<rpc-reply message-id="101"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<data>
<interfaces xmlns="http://example.com/ns/interfaces">
<interface>
<name>eth0</name>
<mtu>8192</mtu>
<status>up</status>
</interface>
<interface>
<name>eth1</name>
<mtu>1500</mtu>
<status>up</status>
</interface>
<interface>
<name>eth2</name>
<mtu>9000</mtu>
<status>not feeling so good</status>
</interface>
<interface>
<name>eth3</name>
<mtu>1500</mtu>
<status>waking up</status>
</interface>
</interfaces>
</data>
</rpc-reply>
A.3.2. <with-defaults> = 'report-all-tagged'
The behavior of the <with-defaults> parameter handling for the value
'report-all-tagged' is demonstrated in this example. A 'tagged' data
node is an element that contains the 'default' XML attribute, set to
Bierman & Lengyel Expires May 15, 2011 [Page 24]
Internet-Draft with-defaults November 2010
'true' or '1'.
The actual data nodes tagged by the server depends on the defaults
handling basic mode used by the server. Only the data nodes that are
considered to be default data will be tagged.
In this example, the server's basic mode is equal to 'trim', so all
data nodes that would contain the schema default value are tagged.
If the server's basic mode is 'explicit', then only data nodes that
are not explicitly set data are tagged. If the server's basic mode
is 'report-all', then no data nodes are tagged.
Bierman & Lengyel Expires May 15, 2011 [Page 25]
Internet-Draft with-defaults November 2010
<rpc message-id="102"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<get>
<filter type="subtree">
<interfaces xmlns="http://example.com/ns/interfaces"/>
</filter>
<with-defaults
xmlns="urn:ietf:params:xml:ns:yang:ietf-netconf-with-defaults">
report-all-tagged
</with-defaults>
</get>
</rpc>
<rpc-reply message-id="102"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0"
xmlns:wd="urn:ietf:params:xml:ns:netconf:default:1.0">
<data>
<interfaces xmlns="http://example.com/ns/interfaces">
<interface>
<name>eth0</name>
<mtu>8192</mtu>
<status wd:default="true">up</status>
</interface>
<interface>
<name>eth1</name>
<mtu wd:default="true">1500</mtu>
<status wd:default="true">up</status>
</interface>
<interface>
<name>eth2</name>
<mtu>9000</mtu>
<status>not feeling so good</status>
</interface>
<interface>
<name>eth3</name>
<mtu wd:default="true">1500</mtu>
<status>waking up</status>
</interface>
</interfaces>
</data>
</rpc-reply>
Bierman & Lengyel Expires May 15, 2011 [Page 26]
Internet-Draft with-defaults November 2010
A.3.3. <with-defaults> = 'trim'
The behavior of the <with-defaults> parameter handling for the value
'trim' is demonstrated in this example.
<rpc message-id="103"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<get>
<filter type="subtree">
<interfaces xmlns="http://example.com/ns/interfaces"/>
</filter>
<with-defaults
xmlns="urn:ietf:params:xml:ns:yang:ietf-netconf-with-defaults">
trim
</with-defaults>
</get>
</rpc>
<rpc-reply message-id="103"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<data>
<interfaces xmlns="http://example.com/ns/interfaces">
<interface>
<name>eth0</name>
<mtu>8192</mtu>
</interface>
<interface>
<name>eth1</name>
</interface>
<interface>
<name>eth2</name>
<mtu>9000</mtu>
<status>not feeling so good</status>
</interface>
<interface>
<name>eth3</name>
<status>waking up</status>
</interface>
</interfaces>
</data>
</rpc-reply>
Bierman & Lengyel Expires May 15, 2011 [Page 27]
Internet-Draft with-defaults November 2010
A.3.4. <with-defaults> = 'explicit'
The behavior of the <with-defaults> parameter handling for the value
'explicit' is demonstrated in this example.
<rpc message-id="104"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<get>
<filter type="subtree">
<interfaces xmlns="http://example.com/ns/interfaces"/>
</filter>
<with-defaults
xmlns="urn:ietf:params:xml:ns:yang:ietf-netconf-with-defaults">
explicit
</with-defaults>
</get>
</rpc>
<rpc-reply message-id="104"
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
<data>
<interfaces xmlns="http://example.com/ns/interfaces">
<interface>
<name>eth0</name>
<mtu>8192</mtu>
<status>up</status>
</interface>
<interface>
<name>eth1</name>
<status>up</status>
</interface>
<interface>
<name>eth2</name>
<mtu>9000</mtu>
<status>not feeling so good</status>
</interface>
<interface>
<name>eth3</name>
<mtu>1500</mtu>
<status>waking up</status>
</interface>
</interfaces>
</data>
</rpc-reply>
Bierman & Lengyel Expires May 15, 2011 [Page 28]
Internet-Draft with-defaults November 2010
Appendix B. Change Log
-- RFC Ed.: remove this section before publication.
B.1. 13-14
Removed reference to RFC 4741 and using 4741bis instead.
B.2. 12-13
Removed with-defaults capability conformance section.
Changed 'wd:default' to 'default'.
Added normative reference to XSD.
Clarified conditional support for with-defaults enumerations, based
on capability parameters.
Clarified that all xs:boolean encoding values must be supported.
Clarified purpose of also-supported parameter in capability URI.
B.3. 11-12
Made editorial clarifications based on AD review.
B.4. 10-11
Changed term 'database' to 'configuration datastore' or generic
'datastore'.
B.5. 09-10
Changed term 'datastore' to 'database'.
Added term 'default value'.
Clarified verbage for data node containing a default value.
B.6. 08-09
Removed non-volatile server requirements.
Moved some text from basic-mode section into the the retrieval modes
section.
Added description and reference statements to the YANG module.
Bierman & Lengyel Expires May 15, 2011 [Page 29]
Internet-Draft with-defaults November 2010
Many bugfixes and clarifications, based on WGLC review comments.
B.7. 07-08
Added report-all-tagged mode.
Changed conformance so report-all or report-all-tagged mode SHOULD be
supported.
Clarified capability requirements for each mode, for edit-config and
NV storage requirements.
Changed rpc-error details for unsupported with-defaults value.
Added XSD for wd:default attribute
Expanded example to show report-all-tagged for a basic-mode=trim
server.
B.8. 06-07
Removed text in capability identifier section about adding YANG
module capability URI parameters.
Changed YANG module namespace to match YANG format, and updated
examples to use this new namespace.
Fixed some typos.
B.9. 05-06
Removed ':1.0' from capability URI.
Removed open issues section because all known issues are closed.
Moved examples to a separate appendix, and expanded them.
Added example.yang as an appendix to properly explain the examples
used within the document.
Replaced normative term 'SHALL' with 'MUST' to be consistent within
this document.
Clarified <with-defaults> behavior for non-configuration data nodes.
Clarified various sections based on WGLC comments on mailing list.
Removed some unused terms.
Bierman & Lengyel Expires May 15, 2011 [Page 30]
Internet-Draft with-defaults November 2010
Reversed the order of the change log sections so the most recent
changes are shown first.
B.10. 04-05
Updated I-D and YANG module boiler-plate.
Removed redundant 'with-defaults' YANG feature.
Changed definition of 'explicit' mode to match the YANG definition
Removed XSD because the YANG is normative and the XSD is
unconstrained, and does not properly extend the 3 affected NETCONF
operations.
Made the YANG module a normative section instead of non-normative
appendix.
Changed YANG from an informative to a normative reference,
Changed 4741bis from an informative to a normative reference because
the YANG module imports the ietf-netconf module in order to augment
some operations.
Updated capability requirements to include YANG module capability
parameters.
Added a description statement to the with-defaults leaf definition.
Update open issues section; ready to close all open issues.
B.11. 03-04
Clarifications
Added non-netconf interfaces to the definition of explicitly set
default data
B.12. 02-03
Clarifications
YAM added
Use the same URN for the capability and the XML namespace to
accommodate YANG, and avoid two separate URN/URIs being advertised in
the HELLO message, for such a small function.
Bierman & Lengyel Expires May 15, 2011 [Page 31]
Internet-Draft with-defaults November 2010
B.13. 01-02
report-all made mandatory
Placeholder for YAM added, XSD will be removed when 4741 provides the
NETCONF YAM
with-defaults is valid for state data as well (if state data has a
defined default which might not be so frequent). The definition of
explicit was modified for state data.
B.14. 00-01
Changed value set of with-default capability and element
Added version to URI
B.15. -00
Created from draft-bierman-netconf-with-defaults-01.txt
It was decided by the NETCONF mailing list, that with-defaults should
be a sub-element of each affected operation. While this violates the
XSD of RFC4741 this is acceptable and follows the ideas behind
NETCONF and YANG.
Hopefully it will be clarified in the 4741bis RFC whether such
extensions are allowed.
Authors' Addresses
Andy Bierman
Brocade
Email: andy.bierman@brocade.com
Balazs Lengyel
Ericsson
Budapest,
Hungary
Email: balazs.lengyel@ericsson.com
Bierman & Lengyel Expires May 15, 2011 [Page 32]
Html markup produced by rfcmarkup 1.122, available from
https://tools.ietf.org/tools/rfcmarkup/