[Docs] [txt|pdf|xml|html] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits] [IPR]

Versions: (draft-daede-netvc-testing) 00 01 02 03 04 05 06 07 08 09

Network Working Group                                           T. Daede
Internet-Draft                                                   Mozilla
Intended status: Informational                                 A. Norkin
Expires: September 01, 2016                                      Netflix
                                                       February 29, 2016


              Video Codec Testing and Quality Measurement
                      draft-ietf-netvc-testing-01

Abstract

   This document describes guidelines and procedures for evaluating a
   video codec specified at the IETF.  This covers subjective and
   objective tests, test conditions, and materials used for the test.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on September 01, 2016.

Copyright Notice

   Copyright (c) 2016 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.




Daede & Norkin         Expires September 01, 2016               [Page 1]


Internet-Draft Video Codec Testing and Quality Measurement February 2016


Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   2.  Subjective quality tests  . . . . . . . . . . . . . . . . . .   2
     2.1.  Still Image Pair Comparison . . . . . . . . . . . . . . .   3
     2.2.  Subjective viewing test . . . . . . . . . . . . . . . . .   3
     2.3.  Expert viewing  . . . . . . . . . . . . . . . . . . . . .   3
   3.  Objective Metrics . . . . . . . . . . . . . . . . . . . . . .   3
     3.1.  Overall PSNR  . . . . . . . . . . . . . . . . . . . . . .   4
     3.2.  Frame-averaged PSNR . . . . . . . . . . . . . . . . . . .   4
     3.3.  PSNR-HVS-M  . . . . . . . . . . . . . . . . . . . . . . .   4
     3.4.  SSIM  . . . . . . . . . . . . . . . . . . . . . . . . . .   5
     3.5.  Multi-Scale SSIM  . . . . . . . . . . . . . . . . . . . .   5
     3.6.  Fast Multi-Scale SSIM . . . . . . . . . . . . . . . . . .   5
     3.7.  CIEDE2000 . . . . . . . . . . . . . . . . . . . . . . . .   5
     3.8.  VMAF  . . . . . . . . . . . . . . . . . . . . . . . . . .   5
   4.  Comparing and Interpreting Results  . . . . . . . . . . . . .   5
     4.1.  Graphing  . . . . . . . . . . . . . . . . . . . . . . . .   5
     4.2.  Bjontegaard . . . . . . . . . . . . . . . . . . . . . . .   6
     4.3.  Ranges  . . . . . . . . . . . . . . . . . . . . . . . . .   6
   5.  Test Sequences  . . . . . . . . . . . . . . . . . . . . . . .   6
     5.1.  Sources . . . . . . . . . . . . . . . . . . . . . . . . .   6
     5.2.  Test Sets . . . . . . . . . . . . . . . . . . . . . . . .   7
     5.3.  Operating Points  . . . . . . . . . . . . . . . . . . . .   7
       5.3.1.  Common settings . . . . . . . . . . . . . . . . . . .   7
       5.3.2.  High Latency  . . . . . . . . . . . . . . . . . . . .   8
       5.3.3.  Unconstrained Low Latency . . . . . . . . . . . . . .   8
   6.  Automation  . . . . . . . . . . . . . . . . . . . . . . . . .   8
     6.1.  Regression tests  . . . . . . . . . . . . . . . . . . . .   9
     6.2.  Objective performance tests . . . . . . . . . . . . . . .   9
     6.3.  Periodic tests  . . . . . . . . . . . . . . . . . . . . .   9
   7.  Informative References  . . . . . . . . . . . . . . . . . . .   9
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  10

1.  Introduction

   When developing a video codec, changes and additions to the codec
   need to be decided based on their performance tradeoffs.  In
   addition, measurements are needed to determine when the codec has met
   its performance goals.  This document specifies how the tests are to
   be carried about to ensure valid comparisons and good decisions.

2.  Subjective quality tests

   Subjective testing is the preferable method of testing video codecs.

   Because the IETF does not have testing resources of its own, it has
   to rely on the resources of its participants.  For this reason, even



Daede & Norkin         Expires September 01, 2016               [Page 2]


Internet-Draft Video Codec Testing and Quality Measurement February 2016


   if the group agrees that a particular test is important, if no one
   volunteers to do it, or if volunteers do not complete it in a timely
   fashion, then that test should be discarded.  This ensures that only
   important tests be done in particular, the tests that are important
   to participants.

2.1.  Still Image Pair Comparison

   A simple way to determine superiority of one compressed image over
   another is to visually compare two compressed images, and have the
   viewer judge which one has a higher quality.  This is mainly used for
   rapid comparisons during development.  For this test, the two
   compressed images should have similar compressed file sizes, with one
   image being no more than 5% larger than the other.  In addition, at
   least 5 different images should be compared.

2.2.  Subjective viewing test

   A subjective viewing test is the preferred method of evaluating the
   quality.  The subjective test should be performed as either
   consecutively showing the video sequences on one screen or on two
   screens located side-by-side.  The testing procedure should normally
   follow rules described in [BT500] and be performed with non-expert
   test subjects.  The result of the test could be (depending on the
   test procedure) mean opinion scores (MOS) or differential mean
   opinion scores (DMOS).  Normally, confidence intervals are also
   calculated to judge whether the difference between two encodings is
   statistically significant.

2.3.  Expert viewing

   An expert viewing test can be performed in the case when an answer to
   a particular question should be found.  An example of such test can
   be a test involving video coding experts on evaluation of a
   particular problem, for example such as comparing the results of two
   de-ringing filters.  Depending on what information is sought, the
   appropriate test procedure can be chosen.

3.  Objective Metrics

   Objective metrics are used in place of subjective metrics for easy
   and repeatable experiments.  Most objective metrics have been
   designed to correlate with subjective scores.

   The following descriptions give an overview of the operation of each
   of the metrics.  Because implementation details can sometimes vary,
   the exact implementation is specified in C in the Daala tools
   repository [DAALA-GIT].



Daede & Norkin         Expires September 01, 2016               [Page 3]


Internet-Draft Video Codec Testing and Quality Measurement February 2016


   All of the metrics described in this document are to be applied to
   the luma plane only.  In addition, they are single frame metrics.
   When applied to the video, the scores of each frame are averaged to
   create the final score.

   Codecs are allowed to internally use downsampling, but must include a
   normative upsampler, so that the metrics run at the same resolution
   as the source video.  In addition, some metrics, such as PSNR and
   FASTSSIM, have poor behavior on downsampled images, so it must be
   noted in test results if downsampling is in effect.

3.1.  Overall PSNR

   PSNR is a traditional signal quality metric, measured in decibels.
   It is directly drived from mean square error (MSE), or its square
   root (RMSE).  The formula used is:

   20 * log10 ( MAX / RMSE )

   or, equivalently:

   10 * log10 ( MAX^2 / MSE )

   where the error is computed over all the pixels in the video, which
   is the method used in the dump_psnr.c reference implementation.

   This metric may be applied to both the luma and chroma planes, with
   all planes reported separately.

3.2.  Frame-averaged PSNR

   PSNR can also be calculated per-frame, and then the values averaged
   together.  This is reported in the same way as overall PSNR.

3.3.  PSNR-HVS-M

   The PSNR-HVS metric performs a DCT transform of 8x8 blocks of the
   image, weights the coefficients, and then calculates the PSNR of
   those coefficients.  Several different sets of weights have been
   considered.  [PSNRHVS] The weights used by the dump_pnsrhvs.c tool in
   the Daala repository have been found to be the best match to real MOS
   scores.









Daede & Norkin         Expires September 01, 2016               [Page 4]


Internet-Draft Video Codec Testing and Quality Measurement February 2016


3.4.  SSIM

   SSIM (Structural Similarity Image Metric) is a still image quality
   metric introduced in 2004 [SSIM].  It computes a score for each
   individual pixel, using a window of neighboring pixels.  These scores
   can then be averaged to produce a global score for the entire image.
   The original paper produces scores ranging between 0 and 1.

   For the metric to appear more linear on BD-rate curves, the score is
   converted into a nonlinear decibel scale:

   -10 * log10 (1 - SSIM)

3.5.  Multi-Scale SSIM

   Multi-Scale SSIM is SSIM extended to multiple window sizes [MSSSIM].

3.6.  Fast Multi-Scale SSIM

   Fast MS-SSIM is a modified implementation of MS-SSIM which operates
   on a limited number of scales and with modified weights [FASTSSIM].
   The final score is converted to decibels in the same manner as SSIM.

3.7.  CIEDE2000

   CIEDE2000 is a metric based on CIEDE color distances [CIEDE2000].  It
   generates a single score taking into account all three chroma planes.
   It does not take into consideration any structural similarity or
   other psychovisual effects.

3.8.  VMAF

   Video Multi-method Assessment Fusion (VMAF) is a full-reference
   perceptual video quality metric that aims to approximate human
   perception of video quality [VMAF].  This metric is focused on
   quality degradation due compression and rescaling.  VMAF estimates
   the perceived quality score by computing scores from multiple quality
   assessment algorithms, and fusing them using a support vector machine
   (SVM).  Currently, three image fidelity metrics and one temporal
   signal have been chosen as features to the SVM, namely Anti-noise SNR
   (ANSNR), Detail Loss Measure (DLM), Visual Information Fidelity
   (VIF), and the mean co-located pixel difference of a frame with
   respect to the previous frame.

4.  Comparing and Interpreting Results

4.1.  Graphing




Daede & Norkin         Expires September 01, 2016               [Page 5]


Internet-Draft Video Codec Testing and Quality Measurement February 2016


   When displayed on a graph, bitrate is shown on the X axis, and the
   quality metric is on the Y axis.  For publication, the X axis should
   be linear.  The Y axis metric should be plotted in decibels.  If the
   quality metric does not natively report quality in decibels, it
   should be converted as described in the previous section.

4.2.  Bjontegaard

   The Bjontegaard rate difference, also known as BD-rate, allows the
   comparison of two different codecs based on a metric.  This is
   commonly done by fitting a curve to each set of data points on the
   plot of bitrate versus metric score, and then computing the
   difference in area between each of the curves.  A cubic polynomial
   fit is common, but will be overconstrained with more than four
   samples.  For higher accuracy, at least 10 samples and a cubic spline
   fit should be used.  In addition, if using a truncated BD-rate curve,
   there should be at least 4 samples within the point of interest.

4.3.  Ranges

   The curve is split into three regions, for low, medium, and high
   bitrate.  The ranges are defined as follows:

   o  Low bitrate: 0.005 - 0.02 bpp

   o  Medium bitrate: 0.02 - 0.06 bpp

   o  High bitrate: 0.06 - 0.2 bpp

   Bitrate can be calculated from bits per pixel (bpp) as follows:

   bitrate = bpp * width * height * framerate

5.  Test Sequences

5.1.  Sources

   Lossless test clips are preferred for most tests, because the
   structure of compression artifacts in already-compressed clips may
   introduce extra noise in the test results.  However, a large amount
   of content on the internet needs to be recompressed at least once, so
   some sources of this nature are useful.  The encoder should run at
   the same bit depth as the original source.  In addition, metrics need
   to support operation at high bit depth.  If one or more codecs in a
   comparison do not support high bit depth, sources need to be
   converted once before entering the encoder.





Daede & Norkin         Expires September 01, 2016               [Page 6]


Internet-Draft Video Codec Testing and Quality Measurement February 2016


5.2.  Test Sets

   Sources are divided into several categories to test different
   scenarios the codec will be required to operate in.  For easier
   comparison, all videos in each set should have the same color
   subsampling, same resolution, and same number of frames.  In
   addition, all test videos must be publicly available for testing use,
   to allow for reproducibility of results.  All current test sets are
   available for download [TESTSEQUENCES].

   o  Still images are useful when comparing intra coding performance.
      Xiph.org has four sets of lossless, one megapixel images that have
      been converted into YUV 4:2:0 format.  There are four sets that
      can be used:

      *  subset1 (50 images)

      *  subset2 (50 images)

      *  subset3 (1000 images)

      *  subset4 (1000 images)

   o  video-hd-3, a set that consists of 1920x1080 clips from
      [DERFVIDEO] (1500 frames total)

   o  vc-360p-1, a low quality video conferencing set (2700 frames
      total)

   o  vc-720p-1, a high quality video conferencing set (2750 frames
      total)

   o  netflix-4k-1, a cinematic 4K video test set (2280 frames total)

   o  netflix-2k-1, a 2K scaled version of netflix-4k-1 (2280 frames
      total)

   o  twitch-1, a game sequence set (2280 frames total)

5.3.  Operating Points

   Two operating modes are defined.  High latency is intended for on
   demand streaming, one-to-many live streaming, and stored video.  Low
   latency is intended for videoconferencing and remote access.

5.3.1.  Common settings





Daede & Norkin         Expires September 01, 2016               [Page 7]


Internet-Draft Video Codec Testing and Quality Measurement February 2016


   Encoders should be configured to their best settings when being
   compared against each other:

   o  vp10: -codec=vp10 -ivf -frame-parallel=0 -tile-columns=0 -cpu-
      used=0 -threads=1

5.3.2.  High Latency

   The encoder should be run at the best quality mode available, using
   the mode that will provide the best quality per bitrate (VBR or
   constant quality mode).  Lookahead and/or two-pass are allowed, if
   supported.  One parameter is provided to adjust bitrate, but the
   units are arbitrary.  Example configurations follow:

   o  x264: -crf=x

   o  x265: -crf=x

   o  daala: -v=x -b 2

   o  vp10: -end-usage=q -cq-level=x -lag-in-frames=25 -auto-alt-ref=2

5.3.3.  Unconstrained Low Latency

   The encoder should be run at the best quality mode available, using
   the mode that will provide the best quality per bitrate (VBR or
   constant quality mode), but no frame delay, buffering, or lookahead
   is allowed.  One parameter is provided to adjust bitrate, but the
   units are arbitrary.  Example configurations follow:

   o  x264: -crf-x -tune zerolatency

   o  x265: -crf=x -tune zerolatency

   o  daala: -v=x

   o  vp10: -end-usage=q -cq-level=x -lag-in-frames=0

6.  Automation

   Frequent objective comparisons are extremely beneficial while
   developing a new codec.  Several tools exist in order to automate the
   process of objective comparisons.  The Compare-Codecs tool allows BD-
   rate curves to be generated for a wide variety of codecs
   [COMPARECODECS].  The Daala source repository contains a set of
   scripts that can be used to automate the various metrics used.  In
   addition, these scripts can be run automatically utilizing
   distributed computers for fast results, with the AreWeCompressedYet



Daede & Norkin         Expires September 01, 2016               [Page 8]


Internet-Draft Video Codec Testing and Quality Measurement February 2016


   tool [AWCY].  Because of computational constraints, several levels of
   testing are specified.

6.1.  Regression tests

   Regression tests run on a small number of short sequences.  The
   regression tests should include a number of various test conditions.
   The purpose of regression tests is to ensure bug fixes (and similar
   patches) do not negatively affect the performance.

6.2.  Objective performance tests

   Changes that are expected to affect the quality of encode or
   bitstream should run an objective performance test.  The performance
   tests should be run on a wider number of sequences.  If the option
   for the objective performance test is chosen, wide range and full
   length simulations are run on the site and the results (including all
   the objective metrics) are generated.

6.3.  Periodic tests

   Periodic tests are run on a wide range of bitrates in order to gauge
   progress over time, as well as detect potential regressions missed by
   other tests.

7.  Informative References

   [AWCY]     Xiph.Org, "Are We Compressed Yet?", 2015, <https://
              arewecompressedyet.com/>.

   [BT500]    ITU-R, "Recommendation ITU-R BT.500-13", 2012, <https://
              www.itu.int/dms_pubrec/itu-r/rec/bt/R-REC-
              BT.500-13-201201-I!!PDF-E.pdf>.

   [CIEDE2000]
              Yang, Y., Ming, J., and N. Yu, "Color Image Quality
              Assessment Based on CIEDE2000", 2012,
              <http://dx.doi.org/10.1155/2012/273723>.

   [COMPARECODECS]
              Alvestrand, H., "Compare Codecs", 2015,
              <http://compare-codecs.appspot.com/>.

   [DAALA-GIT]
              Xiph.Org, "Daala Git Repository", 2015,
              <http://git.xiph.org/?p=daala.git;a=summary>.

   [DERFVIDEO]



Daede & Norkin         Expires September 01, 2016               [Page 9]


Internet-Draft Video Codec Testing and Quality Measurement February 2016


              Terriberry, T., "Xiph.org Video Test Media", n.d., <https:
              //media.xiph.org/video/derf/>.

   [FASTSSIM]
              Chen, M. and A. Bovik, "Fast structural similarity index
              algorithm", 2010, <http://live.ece.utexas.edu/publications
              /2011/chen_rtip_2011.pdf>.

   [L1100]    Bossen, F., "Common test conditions and software reference
              configurations", JCTVC L1100, 2013,
              <http://phenix.int-evry.fr/jct/>.

   [MSSSIM]   Wang, Z., Simoncelli, E., and A. Bovik, "Multi-Scale
              Structural Similarity for Image Quality Assessment", n.d.,
              <http://www.cns.nyu.edu/~zwang/files/papers/msssim.pdf>.

   [PSNRHVS]  Egiazarian, K., Astola, J., Ponomarenko, N., Lukin, V.,
              Battisti, F., and M. Carli, "A New Full-Reference Quality
              Metrics Based on HVS", 2002.

   [SSIM]     Wang, Z., Bovik, A., Sheikh, H., and E. Simoncelli, "Image
              Quality Assessment: From Error Visibility to Structural
              Similarity", 2004,
              <http://www.cns.nyu.edu/pub/eero/wang03-reprint.pdf>.

   [STEAM]    Valve Corporation, "Steam Hardware & Software Survey: June
              2015", June 2015,
              <http://store.steampowered.com/hwsurvey>.

   [TESTSEQUENCES]
              Daede, T., "Test Sets", n.d., <https://people.xiph.org/
              ~tdaede/sets/>.

   [VMAF]     Aaron, A., Li, Z., Manohara, M., Lin, J., Wu, E., and C.
              Kuo, "Challenges in cloud based ingest and encoding for
              high quality streaming media", 2015, <http://
              ieeexplore.ieee.org/xpl/login.jsp?tp=&arnumber=7351097>.

Authors' Addresses

   Thomas Daede
   Mozilla

   Email: tdaede@mozilla.com







Daede & Norkin         Expires September 01, 2016              [Page 10]


Internet-Draft Video Codec Testing and Quality Measurement February 2016


   Andrey Norkin
   Netflix

   Email: anorkin@netflix.com















































Daede & Norkin         Expires September 01, 2016              [Page 11]


Html markup produced by rfcmarkup 1.129d, available from https://tools.ietf.org/tools/rfcmarkup/