[Docs] [txt|pdf|xml|html] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: (draft-crabbe-pce-pce-initiated-lsp) 00 01 02 03 04 05 06 07 08 09 10 11 RFC 8281

PCE Working Group                                              E. Crabbe
Internet-Draft                                    Individual Contributor
Intended status: Standards Track                                I. Minei
Expires: December 24, 2017                                  Google, Inc.
                                                            S. Sivabalan
                                                     Cisco Systems, Inc.
                                                                R. Varga
                                               Pantheon Technologies SRO
                                                           June 22, 2017


  PCEP Extensions for PCE-initiated LSP Setup in a Stateful PCE Model
                  draft-ietf-pce-pce-initiated-lsp-10

Abstract

   The Path Computation Element Communication Protocol (PCEP) provides
   mechanisms for Path Computation Elements (PCEs) to perform path
   computations in response to Path Computation Clients (PCCs) requests.

   The extensions for stateful PCE provide active control of
   Multiprotocol Label Switching (MPLS) Traffic Engineering Label
   Switched Paths (TE LSP) via PCEP, for a model where the PCC delegates
   control over one or more locally configured LSPs to the PCE.  This
   document describes the creation and deletion of PCE-initiated LSPs
   under the stateful PCE model.

Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."




Crabbe, et al.          Expires December 24, 2017               [Page 1]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


   This Internet-Draft will expire on December 24, 2017.

Copyright Notice

   Copyright (c) 2017 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   3
   3.  Architectural Overview  . . . . . . . . . . . . . . . . . . .   4
     3.1.  Motivation  . . . . . . . . . . . . . . . . . . . . . . .   4
     3.2.  Operation Overview  . . . . . . . . . . . . . . . . . . .   5
   4.  Support of PCE-initiated LSPs . . . . . . . . . . . . . . . .   5
     4.1.  STATEFUL-PCE-CAPABILITY TLV . . . . . . . . . . . . . . .   6
   5.  PCE-initiated LSP Instantiation and Deletion  . . . . . . . .   6
     5.1.  The LSP Initiate Request  . . . . . . . . . . . . . . . .   6
     5.2.  The R flag in the SRP Object  . . . . . . . . . . . . . .   7
     5.3.  LSP Instantiation . . . . . . . . . . . . . . . . . . . .   8
       5.3.1.  The Create Flag . . . . . . . . . . . . . . . . . . .  10
       5.3.2.  The SPEAKER-ENTITY-ID TLV . . . . . . . . . . . . . .  11
     5.4.  LSP Deletion  . . . . . . . . . . . . . . . . . . . . . .  11
   6.  LSP Delegation and Cleanup  . . . . . . . . . . . . . . . . .  11
   7.  LSP State Synchronization . . . . . . . . . . . . . . . . . .  12
   8.  Implementation Status . . . . . . . . . . . . . . . . . . . .  13
   9.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  13
     9.1.  PCEP Messages . . . . . . . . . . . . . . . . . . . . . .  13
     9.2.  LSP Object  . . . . . . . . . . . . . . . . . . . . . . .  14
     9.3.  SRP object  . . . . . . . . . . . . . . . . . . . . . . .  14
     9.4.  STATEFUL-PCE-CAPABILITY TLV . . . . . . . . . . . . . . .  14
     9.5.  PCEP-Error Object . . . . . . . . . . . . . . . . . . . .  15
   10. Security Considerations . . . . . . . . . . . . . . . . . . .  15
     10.1.  Malicious PCE  . . . . . . . . . . . . . . . . . . . . .  15
     10.2.  Malicious PCC  . . . . . . . . . . . . . . . . . . . . .  16
   11. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  16
   12. References  . . . . . . . . . . . . . . . . . . . . . . . . .  16
     12.1.  Normative References . . . . . . . . . . . . . . . . . .  16



Crabbe, et al.          Expires December 24, 2017               [Page 2]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


     12.2.  Informative References . . . . . . . . . . . . . . . . .  17
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  18

1.  Introduction

   [RFC5440] describes the Path Computation Element Communication
   Protocol (PCEP).  PCEP defines the communication between a Path
   Computation Client (PCC) and a Path Computation Element (PCE), or
   between PCE and PCE, enabling computation of Multiprotocol Label
   Switching (MPLS) for Traffic Engineering Label Switched Path (TE LSP)
   characteristics.

   [I-D.ietf-pce-stateful-pce] specifies a set of extensions to PCEP to
   enable stateful control of TE LSPs between and across PCEP sessions
   in compliance with [RFC4657].  It includes

   o  mechanisms to effect LSP state synchronization between PCCs and
      PCEs
   o  delegation of control of LSPs to PCEs
   o  PCE control of timing and sequence of path computations within and
      across PCEP sessions

   It focuses on a model where LSPs are configured on the PCC and
   control over them is delegated to the PCE.

   This document describes the setup, maintenance and teardown of PCE-
   initiated LSPs under the stateful PCE model, without the need for
   local configuration on the PCC, thus allowing for a dynamic network
   that is centrally controlled and deployed.

2.  Terminology

   This document uses the following terms defined in [RFC5440]: PCC,
   PCE, PCEP Peer.

   This document uses the following terms defined in [RFC8051]: Stateful
   PCE, Delegation.

   This document uses the following terms defined in
   [I-D.ietf-pce-stateful-pce]: Redelegation Timeout Interval, State
   Timeout Interval, LSP State Report, LSP Update Request.

   The following terms are defined in this document:

   PCE-initiated LSP:  LSP that is instantiated as a result of a request
      from the PCE.





Crabbe, et al.          Expires December 24, 2017               [Page 3]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


   The message formats in this document are specified using Routing
   Backus-Naur Form (RBNF) encoding as specified in [RFC5511].

3.  Architectural Overview

3.1.  Motivation

   [I-D.ietf-pce-stateful-pce] provides active control over LSPs that
   are locally configured on the PCC.  This model relies on the Label
   Edge Router (LER) taking an active role in delegating locally
   configured LSPs to the PCE, and is well suited in environments where
   the LSP placement is fairly static.  However, in environments where
   the LSP placement needs to change in response to application demands,
   it is useful to support dynamic creation and tear down of LSPs.  The
   ability for a PCE to trigger the creation of LSPs on demand can be
   seamlessly integrated into a controller-based network architecture,
   where intelligence in the controller can determine when and where to
   set up paths.

   A possible use case is a software-driven network, where applications
   request network resources and paths from the network infrastructure.
   For example, an application can request a path with certain
   constraints between two LSRs by contacting the PCE.  The PCE can
   compute a path satisfying the constraints, and instruct the head end
   LSR to instantiate and signal it.  When the path is no longer
   required by the application, the PCE can request its teardown.

   Another use case is dynamically adjusting aggregate bandwidth between
   two points in the network using multiple LSPs.  This functionality is
   very similar to auto-bandwidth, but allows for providing the desired
   capacity through multiple LSPs.  This approach overcomes two of the
   limitations auto-bandwidth can experience: 1) growing the capacity
   between the endpoints beyond the capacity of individual links in the
   path and 2) achieving good bin-packing through use of several small
   LSPs instead of a single large one.  The number of LSPs varies based
   on the demand, and LSPs are created and deleted dynamically to
   satisfy the bandwidth requirements.

   Another use case is demand engineering, where a PCE with visibility
   into both the network state and the demand matrix can anticipate and
   optimize how traffic is distributed across the infrastructure.  Such
   optimizations may require creating new paths across the
   infrastructure.








Crabbe, et al.          Expires December 24, 2017               [Page 4]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


3.2.  Operation Overview

   This document defines the new I flag in the STATEFUL-PCE-CAPABILITY
   TLV to indicate that the sender supports PCE-initiated LSPs (see
   details in Section 4.1).  A PCC or PCE sets this flag in the Open
   message during the PCEP Initialization Phase to indicate that it
   supports the procedures of this document.

   This document defines a new PCEP message, the LSP Initiate Request
   (PCInitiate) message, which a PCE can send to a PCE to request the
   initiaton or deletion of an LSP.  The decision when to instantiate or
   delete a PCE-initiated LSP is out of the scope of this document.

   The PCE sends a PCInitiate message to the PCC to request the
   initiation of an LSP.  The PCC creates the LSP using the attributes
   communicated by the PCE and local values for any unspecified
   parameters.  The PCC generates an LSP State Report (PCRpt) for the
   LSP, carrying a newly assigned PLSP-ID for the LSP and delegating the
   LSP to the PCE via the Delegate flag in the LSP object.

   The PCE can update the attributes of the LSP by sending subsequent
   PCUpd messages.  Subsequent LSP State Report (PCRpt) and LSP Update
   Request (PCUpd) messages that the PCC and PCE, respectively, send for
   the LSP will carry the PCC-assigned PLSP-ID, which uniquely
   identifies the LSP.  See details in Section 5.3.

   The PCE sends a PCInitiate message to the PCC to request the deletion
   of an LSP.  To indicate a delete operation, this document defines the
   new R flag in the SRP object in the PCInitiate message, as described
   in Section 5.2.  As a result of the deletion request, the PCC removes
   all state related to the LSP and sends a PCRpt for the removed state.
   See details in Section 5.4.

4.  Support of PCE-initiated LSPs

   A PCEP speaker indicates its ability to support PCE-initiated LSPs
   during the PCEP Initialization phase, as follows.  When the PCEP
   session is created, it sends an Open message with an OPEN object that
   contains the "Stateful PCE Capability" TLV, defined in
   [I-D.ietf-pce-stateful-pce].  A new flag, the I (LSP-INSTANTIATION-
   CAPABILITY) flag, is introduced to this TLV to indicate support for
   instantiation of PCE-initiated LSPs.  A PCE can initiate LSPs only
   for PCCs that advertised this capability.  A PCC will follow the
   procedures described in this document only on sessions where the PCE
   advertised the I flag.






Crabbe, et al.          Expires December 24, 2017               [Page 5]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


4.1.  STATEFUL-PCE-CAPABILITY TLV

   The format of the STATEFUL-PCE-CAPABILITY TLV is shown in the
   following figure:

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |               Type            |            Length=4           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |              Flags                                      |I|S|U|
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++-+-+-+-+-+-+-+-+-+-++-+-+-+-+-+

               Figure 1: STATEFUL-PCE-CAPABILITY TLV format

   The type of the TLV is defined in [I-D.ietf-pce-stateful-pce] and it
   has a fixed length of 4 octets.

   The value comprises a single field - Flags (32 bits).  The U and S
   bits are defined in [I-D.ietf-pce-stateful-pce] and
   [I-D.ietf-pce-stateful-sync-optimizations] respectively.

   I (LSP-INSTANTIATION-CAPABILITY - 1 bit):  If set to 1 by a PCC, the
      I Flag indicates that the PCC allows instantiation of an LSP by a
      PCE.  If set to 1 by a PCE, the I flag indicates that the PCE
      supports instantiating LSPs.  The LSP-INSTANTIATION-CAPABILITY
      flag must be set by both PCC and PCE in order to enable PCE-
      initiated LSP instantiation.

   Unassigned bits are considered reserved.  They MUST be set to 0 on
   transmission and MUST be ignored on receipt.

5.  PCE-initiated LSP Instantiation and Deletion

   To initiate an LSP, a PCE sends a PCInitiate message to a PCC.  The
   message format, objects and TLVs are discussed separately below for
   the creation and the deletion cases.

5.1.  The LSP Initiate Request

   An LSP Initiate Request (PCInitiate) message is a PCEP message sent
   by a PCE to a PCC to trigger LSP instantiation or deletion.  The
   Message-Type field of the PCEP common header for the PCInitiate
   message is set to 12.  The PCInitiate message MUST include the SRP
   and the LSP objects, and MAY contain other objects, as discussed
   later in this section.

   The format of a PCInitiate message is as follows:



Crabbe, et al.          Expires December 24, 2017               [Page 6]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


     <PCInitiate Message> ::= <Common Header>
                              <PCE-initiated-lsp-list>
  Where:
     <Common Header> is defined in [RFC5440]

     <PCE-initiated-lsp-list> ::= <PCE-initiated-lsp-request>
                                  [<PCE-initiated-lsp-list>]

     <PCE-initiated-lsp-request> ::= (<PCE-initiated-lsp-instantiation>|
                                      <PCE-initiated-lsp-deletion>)

     <PCE-initiated-lsp-instantiation> ::= <SRP>
                                           <LSP>
                                           [<END-POINTS>]
                                           <ERO>
                                           [<attribute-list>]

     <PCE-initiated-lsp-deletion> ::= <SRP>
                                      <LSP>

  Where:
     <attribute-list> is defined in [RFC5440] and extended by
     PCEP extensions.

   The SRP object is defined in [I-D.ietf-pce-stateful-pce].  The SRP
   Object contains an SRP-ID-number which is unique within a PCEP
   session.  The PCE increments the last-used SRP-ID-number before it
   sends each PCInitiate message.  The PCC MUST echo the value of the
   SRP-ID-number in PCErr and PCRpt messages that it sends as a result
   of the PCInitiate to allow the PCE to correlate them with the
   corresponding PCInitiate message.

5.2.  The R flag in the SRP Object

   The format of the SRP object is shown in Figure 2:
















Crabbe, et al.          Expires December 24, 2017               [Page 7]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                          Flags                              |R|
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                        SRP-ID-number                          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                                                               |
      //                      Optional TLVs                          //
      |                                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


                      Figure 2: The SRP Object format

   A new flag is defined to indicate a delete operation initiated by the
   PCE:

   R (LSP-REMOVE - 1 bit):  If set to 0, it indicates a request to
      create an LSP.  If set to 1, it indicates a request to remove an
      LSP.

5.3.  LSP Instantiation

   The LSP is instantiated by sending a PCInitiate message.  The LSP is
   set up using RSVP-TE.  Extensions for other setup methods are outside
   the scope of this draft.

   The PCInitiate message, when used to instantiate an LSP, MUST contain
   an LSP object with the reserved PLSP-ID 0.  The LSP Object MUST
   include the SYMBOLIC-PATH-NAME TLV, which is used to correlate
   between the PCC-assigned PLSP-ID and the LSP.

   The PCInitiate message, when used to instantiate an LSP, MUST contain
   an Explicit Route Object (ERO) for the LSP.

   For an instantiation request of an RSVP-signaled LSP, the destination
   address may be needed.  The PCC MAY determine it from a provided
   object (e.g., ERO) or a local decision.  Alternatively, the END-
   POINTS object MAY be included to explicitly convey the destination
   addresses to be used in the RSVP-TE signaling.  The source address
   MAY be either specified or left up to the PCC decision using the
   0.0.0.0 value.  For LSPs to be setup by other means, the END-POINTS
   object MAY be omitted; the exact behavior for other types of LSPs
   will be specified in further documents.

   The PCE MAY include various attributes as per [RFC5440].  The PCC
   MUST use these values in the LSP instantiation, and local values for



Crabbe, et al.          Expires December 24, 2017               [Page 8]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


   unspecified parameters.  After the LSP setup, the PCC MUST send a
   PCRpt to the PCE, reflecting these values.  The SRP object in the
   PCRpt message MUST echo the value of the PCInitiate message that
   triggered the setup.  LSPs that were instantiated as a result of a
   PCInitiate message MUST have the Create flag (Section 5.3.1) set in
   the LSP object.

   If the PCC receives a PCInitiate message with a non-zero PLSP-ID and
   the R flag in the SRP object set to zero, then it MUST send a PCErr
   message with Error-type=19 (Invalid Operation) and Error-value=8
   (Non-zero PLSP-ID in the PCInitiate message).

   If the PCC receives a PCInitiate message without an ERO and the R
   flag in the SRP object set to zero, then it MUST send a PCErr message
   with Error-type=6 (Mandatory Object missing) and Error-value=9 (ERO
   Object missing).

   If the PCC receives a PCInitiate message without a SYMBOLIC-PATH-NAME
   TLV, then it MUST send a PCErr message with Error-type=10 (Invalid
   object) and Error-value=8 (SYMBOLIC-PATH-NAME TLV missing).

   The PCE MUST NOT provide a symbolic path name that conflicts with the
   symbolic path name of any existing LSP in the PCC.  (Existing LSPs
   may be either statically configured, or initiated by another PCE).
   If there is a conflict with the symbolic path name of an existing
   LSP, the PCC MUST send a PCErr message with Error-type=23 (Bad
   Parameter value) and Error-value=1 (SYMBOLIC-PATH-NAME in use).  The
   only exception to this rule is for LSPs for which the State Timeout
   Interval timer is running (see Section 6).

   If the PCC determines that the LSP parameters proposed in the
   PCInitiate message are unacceptable, it MUST send a PCErr message
   with Error-type=24 (PCE instantiation error) and Error-value=1
   (Unacceptable instantiation parameters).  If the PCC encounters an
   internal error during the processing of the PCInitiate message, it
   MUST send a PCErr message with Error-type=24 (PCE instantiation
   error) and Error-value=2 (Internal error).

   A PCC MUST relay to the PCE errors it encounters in the setup of PCE-
   initiated LSP by sending a PCErr message with Error-type=24 (PCE
   instantiation error) and Error-value=3 (Signaling error).  The PCErr
   message MUST echo the SRP-ID-number of the PCInitiate message.  The
   PCEP-ERROR object SHOULD include the RSVP_ERROR_SPEC TLV (if an RSVP
   ERROR_SPEC object was returned to the PCC by a downstream node).
   After the LSP is set up, errors in RSVP signaling are reported in
   PCRpt messages, as described in [I-D.ietf-pce-stateful-pce].





Crabbe, et al.          Expires December 24, 2017               [Page 9]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


   On successful completion of the LSP instantiation, the PCC MUST send
   a PCRpt message.  The LSP object message MUST contain a non-zero
   PLSP-ID that uniquely identifies the LSP within this PCC, and MUST
   have the Create flag (Section 5.3.1) and Delegate flag set.  The SRP
   object MUST contain an SRP-ID-number that echoes the value from the
   PCInitiate message that triggered the setup.  The PCRpt MUST include
   the attributes that the PCC used to instantiate the LSP.

   A PCC SHOULD be able to place a limit on either the number of LSPs or
   the percentage of resources that are allocated to honor PCE-initiated
   LSP requests.  As soon as that limit is reached, the PCC MUST send a
   PCErr message with Error-type=19 (Invalid Operation) and Error-
   value=6 (PCE-initiated LSP limit reached) and is free to drop any
   incoming PCInitiate messages without additional processing.

   Similarly, the PCE SHOULD be able to place a limit on either the
   number of PCInitiate messages pending for a particular PCC, or on the
   time it waits for a response (positive or negative) to a PCInitiate
   message from a PCC and MAY take further action (such as closing the
   session or removing all its LSPs) if this limit is reached.

5.3.1.  The Create Flag

   The LSP object is defined in [I-D.ietf-pce-stateful-pce] and included
   here for easy reference.

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                PLSP-ID                |Flags  |C|  O  |A|R|S|D|
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     //                        TLVs                                 //
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                      Figure 3: The LSP Object format

   A new flag, the Create (C) flag is introduced.  On a PCRpt message,
   the C Flag set to 1 indicates that this LSP was created via a
   PCInitiate message.  The C Flag MUST be set to 1 on each PCRpt
   message for the duration of existence of the LSP.  The Create flag
   allows PCEs to be aware of which LSPs were PCE-initiated (a state
   that would otherwise only be known by the PCC and the PCE that
   initiated them).







Crabbe, et al.          Expires December 24, 2017              [Page 10]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


5.3.2.  The SPEAKER-ENTITY-ID TLV

   The optional SPEAKER-ENTITY-ID TLV defined in
   [I-D.ietf-pce-stateful-sync-optimizations] MAY be included in the LSP
   object in a PCRpt message, as an optional TLV for LSPs for which the
   C flag is 1.  The SPEAKER-ENTITY-ID TLV identifies the PCE which
   initiated the creation of the LSP on all PCEP sessions, a state that
   would otherwise only be known by the PCC and the PCE that initiated
   the LSP.  If the TLV appears in a PCRpt for an LSP for which the C
   flag is 0, the LSP MUST be ignored and the PCE MUST send a PCErr
   message with Error-type=23 ("Bad parameter value") and Error-value=2
   ("Speaker identity included for an LSP that is not PCE-initiated").

5.4.  LSP Deletion

   A PCE can initiate the removal of a PCE-initiated LSP by sending a
   PCInitiate message with an LSP object carrying the PLSP-ID of the LSP
   to be removed and an SRP object with the R flag set (see
   Section 5.2).  A PLSP-ID of zero removes all LSPs that were initiated
   by the PCE.

   If the PLSP-ID is unknown, the PCC MUST send a PCErr message with
   Error-type=19 ("Invalid operation") and Error-value=3 ("Unknown PLSP-
   ID") ([I-D.ietf-pce-stateful-pce]).

   If the PLSP-ID specified in the PCInitiate message is not delegated
   to the PCE, the PCC MUST send a PCErr message with Error-type=19
   ("Invalid operation") and Error-value=1 ("LSP is not delegated")
   ([I-D.ietf-pce-stateful-pce]).

   If the PLSP-ID specified in the PCInitiate message was not created by
   a PCE, the PCC MUST send a PCErr message with Error-type=19 ("Invalid
   operation") and Error-value=9 ("LSP is not PCE-initiated").

   Following the removal of the LSP, the PCC MUST send a PCRpt as
   described in [I-D.ietf-pce-stateful-pce].  The SRP object in the
   PCRpt MUST include the SRP-ID-number from the PCInitiate message that
   triggered the removal.  The R flag in the SRP object MUST be set.

6.  LSP Delegation and Cleanup

   The PCC MUST delegate PCE-initiated LSPs to the PCE upon
   instantiation.  The PCC MUST set the delegation bit to 1 in the PCRpt
   that includes the assigned PLSP-ID.

   The PCC MUST NOT revoke the delegation for a PCE-initiated LSP on an
   active PCEP session.  Therefore, all PCRpt messages from the PCC to
   the PCE that owns the delegation MUST have the delegation bit set to



Crabbe, et al.          Expires December 24, 2017              [Page 11]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


   1.  If the PCE that owns the delegation receives a PCRpt message with
   the delegation bit set to 0 then it MUST send a PCErr message with
   Error-type=19 ("Invalid Operation") and Error-value=7 ("Delegation
   for PCE-initiated LSP cannot be revoked").  The PCE MAY further react
   by closing the session.

   Control over a PCE-initiated LSP can revert to the PCC in two ways.
   A PCE MAY return a delegation to the PCC to allow for LSP transfer
   between PCEs.  Alternatively, the PCC gains control an LSP if the
   PCEP session that it was delegated on fails and the Redelegation
   Timeout Interval timer expires.  In both cases, the LSP becomes an
   orphan until the expiration of the State Timeout Interval timer
   ([I-D.ietf-pce-stateful-pce]).

   The PCC MAY attempt to redelegate an orphaned LSP by following the
   procedures of [I-D.ietf-pce-stateful-pce].  Alternatively, if the
   orphaned LSP was PCE-initiated, then a PCE MAY obtain control over
   it, as follows.

   A PCE (either the original or one of its backups) sends a PCInitiate
   message, including just the SRP and LSP objects, and carrying the
   PLSP-ID of the LSP it wants to take control of.  If the PCC receives
   a PCInitiate message with a PLSP-ID pointing to an orphaned PCE-
   initiated LSP, then it MUST redelegate that LSP to the PCE.  Any
   other non-zero PLSP-ID MUST result in the generation of a PCErr
   message using the rules described in Section 5.4.  The State Timeout
   Interval timer for the LSP is stopped upon the redelegation.  After
   obtaining control of the LSP, the PCE may remove it using the
   procedures described in this document.

   The State Timeout Interval timer ensures that a PCE crash does not
   result in automatic and immediate disruption for the services using
   PCE-initiated LSPs.  PCE-initiated LSPs are not removed immediately
   upon PCE failure.  Instead, they are cleaned up on the expiration of
   this timer.  This allows for network cleanup without manual
   intervention.  The PCC SHOULD support removal of PCE-initiated LSPs
   as one of the behaviors applied on expiration of the State Timeout
   Interval timer.  The behavior SHOULD be picked based on local policy,
   and can result either in LSP removal, or in reverting to operator-
   defined default parameters.

7.  LSP State Synchronization

   LSP State Synchronization procedures are described in section 5.4 of
   [I-D.ietf-pce-stateful-pce].  During State Synchronization, a PCC
   reports the state of its LSPs to the PCE using PCRpt messages,
   setting the SYNC flag in the LSP Object.  For PCE-initiated LSPs, the
   PCC MUST also set the Create Flag in the LSP Object and MAY include



Crabbe, et al.          Expires December 24, 2017              [Page 12]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


   the SPEAKER-ENTITY-ID TLV identifying the PCE that requested the LSP
   creation.  At the end of state synchronization, the PCE SHOULD
   compare the reported PCE-Initiated LSPs with its configuration.  For
   any mismatch, the PCE SHOULD send a PCInitiate message to initiate
   any missing LSPs and/or remove any LSPs that are not wanted.

8.  Implementation Status

   This section to be removed by the RFC editor.

   This section records the status of known implementations of the
   protocol defined by this specification at the time of posting of this
   Internet-Draft, and is based on a proposal described in [RFC7942].
   The description of implementations in this section is intended to
   assist the IETF in its decision processes in progressing drafts to
   RFCs.  Please note that the listing of any individual implementation
   here does not imply endorsement by the IETF.  Furthermore, no effort
   has been spent to verify the information presented here that was
   supplied by IETF contributors.  This is not intended as, and must not
   be construed to be, a catalog of available implementations or their
   features.  Readers are advised to note that other implementations may
   exist.

   According to RFC 7942, "this will allow reviewers and working groups
   to assign due consideration to documents that have the benefit of
   running code, which may serve as evidence of valuable experimentation
   and feedback that have made the implemented protocols more mature.
   It is up to the individual working groups to use this information as
   they see fit".

   Two vendors are implementing the extensions described in this draft
   and have included the functionality in releases that will be shipping
   in the near future.  An additional entity is working on implementing
   these extensions in the scope of research projects.

9.  IANA Considerations

   This document requests IANA actions to allocate code points for the
   protocol elements defined in this document.

9.1.  PCEP Messages

   IANA is requested to confirm the early allocation of the following
   new message type within the "PCEP Messages" sub-registry of the PCEP
   Numbers registry, and to update the reference in the registry to
   point to this document, when it is an RFC:





Crabbe, et al.          Expires December 24, 2017              [Page 13]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


                 Value     Meaning               Reference
                   12      LSP Initiate Request  This document

   Note to IANA: The early allocation was done for a message called
   "Initiate".  This name has changed to "LSP Initiate Request" as
   above.

9.2.  LSP Object

   [I-D.ietf-pce-stateful-pce] defines the LSP Object and requests that
   IANA creates a registry to manage the value of the LSP Object's Flag
   field.  IANA is requested to allocate a new bit in the LSP Object
   Flag Field registry, as follows:

                 Bit     Description           Reference

                  4      Create                This document

9.3.  SRP object

   This document requests that a new sub-registry, named "SRP Object
   Flag Field", is created within the "Path Computation Element Protocol
   (PCEP) Numbers" registry to manage the Flag field of the SRP object.
   New values are to be assigned by Standards Action [RFC5226].  Each
   bit should be tracked with the following qualities: bit number
   (counting from bit 0 as the most significant bit), description and
   defining RFC.

   The following values are defined in this document:

                 Bit     Description           Reference

                  31     LSP-Remove            This document

9.4.  STATEFUL-PCE-CAPABILITY TLV

   [I-D.ietf-pce-stateful-pce] defines the STATEFUL-PCE-CAPABILITY TLV
   and requests that IANA creates a registry to manage the value of the
   STATEFUL-PCE-CAPABILITY TLV's Flag field.  IANA is requested to
   allocate a new bit in the STATEFUL-PCE-CAPABILITY TLV Flag Field
   registry, as follows:

             Bit    Description                    Reference

              29    I (LSP-INSTANTIATION-          This document
                    CAPABILITY)





Crabbe, et al.          Expires December 24, 2017              [Page 14]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


9.5.  PCEP-Error Object

   IANA is requested to confirm the early allocation of the following
   new error types and error values within the "PCEP-ERROR Object Error
   Types and Values" sub-registry of the PCEP Numbers registry, and to
   update the reference in the registry to point to this document, when
   it is an RFC:


    Error-Type  Meaning
       10       Invalid Object

                 Error-value=8:  SYMBOLIC-PATH-NAME TLV missing
       19       Invalid operation

                 Error-value=6:  PCE-initiated LSP limit reached
                 Error-value=7:  Delegation for PCE-initiated LSP cannot
                                 be revoked
                 Error-value=8:  Non-zero PLSP-ID in PCInitiate message
                 Error-value=9:  LSP is not PCE-initiated
                 Error-value=10: PCE-initiated operation-frequency limit
                                 reached
       23       Bad parameter value

                 Error-value=1:  SYMBOLIC-PATH-NAME in use
                 Error-value=2:  Speaker identity included for an LSP
                                 that is not PCE-initiated
       24       LSP instantiation error

                 Error-value=1:  Unacceptable instantiation parameters
                 Error-value=2:  Internal error
                 Error-value=3:  Signaling error

10.  Security Considerations

   The security considerations described in [I-D.ietf-pce-stateful-pce]
   apply to the extensions described in this document.  Additional
   considerations related to a malicious PCE are introduced.

10.1.  Malicious PCE

   The LSP instantiation mechanism described in this document allows a
   PCE to generate state on the PCC and throughout the network.  As a
   result, it introduces a new attack vector: an attacker may flood the
   PCC with LSP instantiation requests and consume network and LSR
   resources, either by spoofing messages or by compromising the PCE
   itself.




Crabbe, et al.          Expires December 24, 2017              [Page 15]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


   A PCC can protect itself from such an attack by imposing a limit on
   either the number of LSPs or the percentage of resources that are
   allocated to honor PCE-initiated LSP requests.  As soon as that limit
   is reached, the PCC MUST send a PCErr message with Error-type=19
   ("Invalid Operation") and Error-value=6 ("PCE-initiated LSP limit
   reached") and is free to drop any incoming PCInitiate messages for
   LSP instantiation without additional processing.

   Rapid flaps triggered by the PCE can also be an attack vector.  A PCC
   can protect itself from such an attack by imposing a limit on the
   number of flaps per unit of time that it allows a PCE to generate.
   As soon as that limit is reached, a PCC MUST send a PCErr message
   with Error-type=19 ("Invalid Operation") and Error-value=10 ("PCE-
   initiated operation frequency reached") and is free to treat the
   session as having reached the limit in terms of resources allocated
   to honor PCE-initiated LSP requests, either permanently or for a
   locally-defined cool-off period.

10.2.  Malicious PCC

   The LSP instantiation mechanism described in this document requires
   the PCE to keep state for LSPs that it instantiates and relies on the
   PCC responding (with either a state report or an error message) to
   requests for LSP instantiation.  A malicious PCC or one that reached
   the limit of the number of PCE-initiated LSPs, can ignore PCE
   requests and consume PCE resources.  A PCE can protect itself by
   imposing a limit on the number of requests pending, or by setting a
   timeout and it MAY take further action such as closing the session or
   removing all the LSPs it initiated.

11.  Acknowledgements

   We would like to thank Jan Medved, Ambrose Kwong, Ramon Casellas,
   Cyril Margaria, Dhruv Dhody, Raveendra Trovi and Jon Hardwick for
   their contributions to this document.

12.  References

12.1.  Normative References

   [I-D.ietf-pce-stateful-pce]
              Crabbe, E., Minei, I., Medved, J., and R. Varga, "PCEP
              Extensions for Stateful PCE", draft-ietf-pce-stateful-
              pce-21 (work in progress), June 2017.







Crabbe, et al.          Expires December 24, 2017              [Page 16]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <http://www.rfc-editor.org/info/rfc2119>.

   [RFC5440]  Vasseur, JP., Ed. and JL. Le Roux, Ed., "Path Computation
              Element (PCE) Communication Protocol (PCEP)", RFC 5440,
              DOI 10.17487/RFC5440, March 2009,
              <http://www.rfc-editor.org/info/rfc5440>.

   [RFC5511]  Farrel, A., "Routing Backus-Naur Form (RBNF): A Syntax
              Used to Form Encoding Rules in Various Routing Protocol
              Specifications", RFC 5511, DOI 10.17487/RFC5511, April
              2009, <http://www.rfc-editor.org/info/rfc5511>.

12.2.  Informative References

   [I-D.ietf-pce-stateful-sync-optimizations]
              Crabbe, E., Minei, I., Medved, J., Varga, R., Zhang, X.,
              and D. Dhody, "Optimizations of Label Switched Path State
              Synchronization Procedures for a Stateful PCE", draft-
              ietf-pce-stateful-sync-optimizations-10 (work in
              progress), March 2017.

   [RFC4657]  Ash, J., Ed. and J. Le Roux, Ed., "Path Computation
              Element (PCE) Communication Protocol Generic
              Requirements", RFC 4657, DOI 10.17487/RFC4657, September
              2006, <http://www.rfc-editor.org/info/rfc4657>.

   [RFC5226]  Narten, T. and H. Alvestrand, "Guidelines for Writing an
              IANA Considerations Section in RFCs", BCP 26, RFC 5226,
              DOI 10.17487/RFC5226, May 2008,
              <http://www.rfc-editor.org/info/rfc5226>.

   [RFC7942]  Sheffer, Y. and A. Farrel, "Improving Awareness of Running
              Code: The Implementation Status Section", BCP 205,
              RFC 7942, DOI 10.17487/RFC7942, July 2016,
              <http://www.rfc-editor.org/info/rfc7942>.

   [RFC8051]  Zhang, X., Ed. and I. Minei, Ed., "Applicability of a
              Stateful Path Computation Element (PCE)", RFC 8051,
              DOI 10.17487/RFC8051, January 2017,
              <http://www.rfc-editor.org/info/rfc8051>.








Crabbe, et al.          Expires December 24, 2017              [Page 17]


Internet-Draft      Stateful PCE - PCE-initiated LSP           June 2017


Authors' Addresses

   Edward Crabbe
   Individual Contributor

   Email: edward.crabbe@gmail.com


   Ina Minei
   Google, Inc.
   1600 Amphitheatre Parkway
   Mountain View, CA  94043
   US

   Email: inaminei@google.com


   Siva Sivabalan
   Cisco Systems, Inc.
   170 West Tasman Dr.
   San Jose, CA  95134
   US

   Email: msiva@cisco.com


   Robert Varga
   Pantheon Technologies SRO
   Mlynske Nivy 56
   Bratislava  821 05
   Slovakia

   Email: robert.varga@pantheon.tech


















Crabbe, et al.          Expires December 24, 2017              [Page 18]


Html markup produced by rfcmarkup 1.129b, available from https://tools.ietf.org/tools/rfcmarkup/