[Docs] [txt|pdf] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]
Versions: (draft-dekok-radext-radius-extensions)
00 01 02 03 04 05 06 07 08 09 13 RFC 6929
Network Working Group Alan DeKok
INTERNET-DRAFT Network RADIUS
Category: Proposed Standard Avi Lior
Updates: 2865, 2866, 3575, 5176, 6158 BWS
<draft-ietf-radext-radius-extensions-08.txt>
Expires: July 8, 2013
8 January 2013
Remote Authentication Dial In User Service (RADIUS) Protocol
Extensions
draft-ietf-radext-radius-extensions-08.txt
Abstract
The Remote Authentication Dial In User Service (RADIUS) protocol is
nearing exhaustion of its current 8-bit Attribute Type space. In
addition, experience shows a growing need for complex grouping, along
with attributes which can carry more than 253 octets of data. This
document defines changes to RADIUS which address all of the above
problems.
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on June 26, 2013.
Copyright Notice
DeKok, Alan Standards Track [Page 1]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info/) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
DeKok, Alan Standards Track [Page 2]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
Table of Contents
1. Introduction ............................................. 5
1.1. Caveats and Limitations ............................. 6
1.1.1. Failure to Meet Certain Goals .................. 6
1.1.2. Implementation Recommendations ................. 6
1.2. Terminology ......................................... 7
1.3. Requirements Language ............................... 8
2. Extensions to RADIUS ..................................... 9
2.1. Extended Type ....................................... 10
2.2. Long Extended Type .................................. 11
2.3. TLV Data Type ....................................... 13
2.3.1. TLV Nesting .................................... 15
2.4. EVS Data Type ....................................... 16
2.5. Integer64 Data Type ................................. 17
2.6. Vendor-ID Field ..................................... 18
2.7. Attribute Naming and Type Identifiers ............... 18
2.7.1. Attribute and TLV Naming ....................... 18
2.7.2. Attribute Type Identifiers ..................... 19
2.7.3. TLV Identifiers ................................ 19
2.7.4. VSA Identifiers ................................ 20
2.8. Invalid Attributes .................................. 20
3. Attribute Definitions .................................... 21
3.1. Extended-Type-1 ..................................... 22
3.2. Extended-Type-2 ..................................... 23
3.3. Extended-Type-3 ..................................... 23
3.4. Extended-Type-4 ..................................... 24
3.5. Long-Extended-Type-1 ................................ 25
3.6. Long-Extended-Type-2 ................................ 26
4. Vendor Specific Attributes ............................... 28
4.1. Extended-Vendor-Specific-1 .......................... 28
4.2. Extended-Vendor-Specific-2 .......................... 29
4.3. Extended-Vendor-Specific-3 .......................... 30
4.4. Extended-Vendor-Specific-4 .......................... 31
4.5. Extended-Vendor-Specific-5 .......................... 33
4.6. Extended-Vendor-Specific-6 .......................... 34
5. Compatibility with traditional RADIUS .................... 35
5.1. Attribute Allocation ................................ 36
5.2. Proxy Servers ....................................... 37
6. Guidelines ............................................... 38
6.1. Updates to RFC 6158 ................................. 38
6.2. Guidelines for Simple Data Types .................... 38
6.3. Guidelines for Complex Data Types ................... 39
6.4. Guidelines For the New Types ........................ 39
6.5. Allocation Request Guidelines ....................... 40
6.6. TLV Guidelines ...................................... 41
6.7. Implementation Guidelines ........................... 41
6.8. Vendor Guidelines ................................... 42
DeKok, Alan Standards Track [Page 3]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
7. Rationale for This Design ................................ 42
7.1. Attribute Audit ..................................... 42
8. Diameter Considerations .................................. 43
9. Examples ................................................. 43
9.1. Extended Type ....................................... 45
9.2. Long Extended Type .................................. 46
10. IANA Considerations ..................................... 48
10.1. Attribute Allocations .............................. 49
10.2. RADIUS Attribute Type Tree ......................... 49
10.3. Allocation Instructions ............................ 50
10.3.1. Requested Allocation from the Standard Space .. 50
10.3.2. Requested Allocation from the short extended sp 50
10.3.3. Requested Allocation from the long extended spa 51
10.3.4. Allocation Preferences ........................ 51
10.3.5. Extending the Type Space via TLV Data Type .... 51
10.3.6. Allocation within a TLV ....................... 52
10.3.7. Allocation of Other Data Types ................ 52
11. Security Considerations ................................. 52
12. References .............................................. 53
12.1. Normative references ............................... 53
12.2. Informative references ............................. 53
Appendix A - Extended Attribute Generator Program ............ 55
DeKok, Alan Standards Track [Page 4]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
1. Introduction
Under current allocation pressure, we expect that the RADIUS
Attribute Type space will be exhausted by 2014 or 2015. We therefore
need a way to extend the type space, so that new specifications may
continue to be developed. Other issues have also been shown with
RADIUS. The attribute grouping method defined in [RFC2868] has been
shown to be impractical, and a more powerful mechanism is needed.
Multiple attributes have been defined which transport more than the
253 octets of data originally envisioned with the protocol. Each of
these attributes is handled as a "special case" inside of RADIUS
implementations, instead of as a general method. We therefore also
need a standardized method of transporting large quantities of data.
Finally, some vendors are close to allocating all of the Attributes
within their Vendor-Specific Attribute space. It would be useful to
leverage changes to the base protocol for extending the Vendor-
Specific Attribute space.
We satisfy all of these requirements through the following changes
given in this document:
* defining an "Extended Type" format, which adds 8 bits of "Extended
Type" to the RADIUS Attribute Type space, by using one octet of the
"Value" field. This method gives us a general way of extending
the Attribute Type Space. (Section 2.1)
* allocating 4 attributes as using the format of "Extended Type".
This allocation extends the RADIUS Attribute Type Space by
approximately 1000 values. (Sections 3.1, 3.2, 3.3, and 3.4)
* defining a "Long Extended Type" format, which inserts an additional
octet between the "Extended Type" octet, and the "Value" field.
This method gives us a general way of adding additional
functionality to the protocol. (Section 2.2)
* defining a method which uses the additional octet in the "Long
Extended Type" to indicate data fragmentation across multiple
Attributes. This method provides a standard way for an Attribute
to carry more than 253 octets of data. (Section 2.2)
* allocating 2 attributes as using the format "Long Extended Type".
This allocation extends the RADIUS Attribute Type Space
by an additional 500 values. (Sections 3.5 and 3.6)
* defining a new "Type Length Value" (TLV) data type. The data type
allows an attribute to carry TLVs as "sub-attributes", which can in
turn encapsulate other TLVs as "sub-sub-attributes." This change
creates a standard way to group a set of Attributes. (Section 2.3)
DeKok, Alan Standards Track [Page 5]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
* defining a new "extended Vendor-Specific" (EVS) data type. The
data type allows an attribute to carry Vendor-Specific Attributes
(VSAs) inside of the new attribute formats. (Section 2.4)
* defining a new "integer64" data type. The data type allows
counters which track more than 2^32 octets of data. (Section 2.5)
* allocating 6 attributes using the new EVS data type. This
allocation extends the Vendor-Specific Attribute Type space by
over 1500 values. (Sections 4.1 through 4.6)
* Define the "Vendor-ID" for Vendor-Specific attributes to encompass
the entire 4 octets of the Vendor field. [RFC2865] Section 5.26
defined it to be 3 octets, with the high octet being zero.
(Section 2.5)
* Describing compatibility with existing RADIUS systems. (Section 5)
* Defining guidelines for the use of these changes for IANA,
implementations of this specification, and for future RADIUS
specifications. (Section 6)
As with any protocol change, the changes defined here are the result
of a series of compromises. We have tried to find a balance between
flexibility, space in the RADIUS message, compatibility with existing
deployments, and implementation difficulty.
1.1. Caveats and Limitations
This section describes some caveats and limitations with the
proposal.
1.1.1. Failure to Meet Certain Goals
One gaol which was not met by the above modifications is to have an
incentive for standards to use the new space. We would ideally like
to deprecate the "Unassigned" attributes in the standard space, which
would permit allocation, but under more stringent guidelines.
However, [RFC5226] has no provisions for a "Deprecated" entry in an
IANA managed registry.
1.1.2. Implementation Recommendations
It is RECOMMENDED that implementations support this specification.
It is RECOMMENDED that new specifications use the formats defined in
this specification.
The alternative to the above recommendations is a circular argument
DeKok, Alan Standards Track [Page 6]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
of not implementing this specification because no other standards
reference it, and also not defining new standards referencing this
specification because no implementations exist.
As noted earlier, the "standard space" is almost entirely allocated.
Ignoring the looming crisis benefits no one.
1.2. Terminology
This document uses the following terms:
silently discard
This means the implementation discards the packet without further
processing. The implementation MAY provide the capability of
logging the error, including the contents of the silently discarded
packet, and SHOULD record the event in a statistics counter.
invalid attribute
This means that the Length field of an Attribute is valid (as per
[RFC2865], Section 5, top of page 25). However, the Value field of
the attribute does not follow the format required by the data type
defined for that Attribute. e.g. an Attribute of type "address"
which encapsulates more than four, or less than four, octets of
data. See Section 2.8 for a more complete definition.
Standard space
Codes in the RADIUS Attribute Type Space that are allocated by IANA
and that follow the format defined in Section 5 of [RFC2865].
Extended space
Codes in the RADIUS Attribute Type Space that require the
extensions defined in this document, and are an extension of the
standard space, but which cannot be represented within the standard
space.
Short extended space
Codes in the extended space which use the "Extended Type" format.
Long extended space
Codes in the extended space which use the "Long Extended Type"
format.
The following terms are used here with the meanings defined in BCP
DeKok, Alan Standards Track [Page 7]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
26 [RFC5226]: "name space", "assigned value", "registration",
"Private Use", "Reserved", "Unassigned", "IETF Review", and
"Standards Action".
1.3. Requirements Language
In this document, several words are used to signify the requirements
of the specification. The key words "MUST", "MUST NOT", "REQUIRED",
"SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY",
and "OPTIONAL" in this document are to be interpreted as described in
[RFC2119].
DeKok, Alan Standards Track [Page 8]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
2. Extensions to RADIUS
This section defines two new attribute formats; "Extended Type"; and
"Long Extended Type". It defines a new Type-Length-Value (TLV) data
type, an Extended-Vendor-Specific (EVS) data type, and an Integer64
data type. It defines a new method for naming attributes and
identifying Attributes using the new attribute formats. It finally
defines the new term "invalid attribute", and describes how it
affects implementations.
The new attribute formats are designed to be compatible with the
attribute format given in [RFC2865] Section 5. The meaning and
interpretation of the Type and Length fields is unchanged from that
specification. This reuse allows the new formats to be compatible
RADIUS implementations which do not implement this specification.
Those implementations can simply ignore the Value field of an
attribute, or forward it verbatim.
The changes to the attribute format come about by "stealing" one or
more octets from the Value field. This change has the effect that
the Value field of [RFC2865] Section 5 contains both the new octets
given here, and any attribute-specific Value. The result is that
Values in this specification are limited to less than 253 octets in
size. This limitation is overcome through the use of the "Long
Extended Type" format.
We reiterate that the formats given in this document do not insert
new data into an attribute. Instead, we "steal" one octet of Value,
so that the definition of the Length field remains unchanged. The
new attribute formats are designed to be compatible with the
attribute format given in [RFC2865] Section 5. The meaning and
interpretation of the Type and Length fields is unchanged from that
specification. This reuse allows the new formats to be compatible
RADIUS implementations which do not implement this specification.
Those implementations can simply ignore the Value field of an
attribute, or forward it verbatim.
The changes to the attribute format come about by "stealing" one or
more octets from the Value field. This change has the effect that
the Value field of [RFC2865] Section 5 contains both the new octets
given here, and any attribute-specific Value. The result is that
Values in this specification are limited to less than 253 octets in
size. This limitation is overcome through the use of the "Long
Extended Type" format.
We reiterate that the formats given in this document do not insert
new data into an attribute. Instead, we "steal" one octet of Value,
so that the definition of the Length field remains unchanged.
DeKok, Alan Standards Track [Page 9]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
2.1. Extended Type
This section defines a new attribute format, called "Extended Type".
A summary of the Attribute format is shown below. The fields are
transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Extended-Type | Value ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
This field is identical to the Type field of the Attribute format
defined in [RFC2865] Section 5.
Length
The Length field is one octet, and indicates the length of this
Attribute including the Type, Length, Extended-Type, and Value
fields. Permitted values are between 4 and 255. If a client or
server receives an Extended Attribute with a Length of 2 or 3,
then that Attribute MUST be considered to be an "invalid
attribute", and handled as per Section 2.8, below.
Extended-Type
The Extended-Type field is one octet. Up-to-date values of this
field are specified according to the policies and rules described
in Section 10. Unlike the Type field defined in [RFC2865] Section
5, no values are allocated for experimental or implementation-
specific use. Values 241-255 are reserved and SHOULD NOT be used.
The Extended-Type is meaningful only within a context defined by
the Type field. That is, this field may be thought of as defining
a new type space of the form "Type.Extended-Type". See Section
2.5, below, for additional discussion.
A RADIUS server MAY ignore Attributes with an unknown
"Type.Extended-Type".
A RADIUS client MAY ignore Attributes with an unknown
"Type.Extended-Type".
Value
This field is similar to the Value field of the Attribute format
DeKok, Alan Standards Track [Page 10]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
defined in [RFC2865] Section 5. The format of the data SHOULD be
a valid RADIUS data type.
The addition of the Extended-Type field decreases the maximum
length for attributes of type "text" or "string" from 253 to 252
octets. Where an Attribute needs to carry more than 252 octets of
data, the "Long Extended Type" format SHOULD be used.
Experience has shown that the "experimental" and "implementation
specific" attributes defined in [RFC2865] Section 5 have had little
practical value. We therefore do not continue that practice here
with the Extended-Type field.
2.2. Long Extended Type
This section defines a new attribute format, called "Long Extended
Type". It leverages the "Extended Type" format in order to permit
the transport of attributes encapsulating more than 253 octets of
data. A summary of the Attribute format is shown below. The fields
are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Extended-Type |M| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
This field is identical to the Type field of the Attribute format
defined in [RFC2865] Section 5.
Length
The Length field is one octet, and indicates the length of this
Attribute including the Type, Length, Extended-Type, and Value
fields. Permitted values are between 5 and 255. If a client or
server receives a "Long Extended Type" with a Length of 2, 3, or
4, then that Attribute MUST be considered to be an "invalid
attribute", and be handled as per Section 2.8, below.
Note that this Length is limited to the length of this fragment.
There is no field which gives an explicit value for the total size
of the fragmented attribute.
Extended-Type
DeKok, Alan Standards Track [Page 11]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
This field is identical to the Extended-Type field defined above
in Section 2.1.
M (More)
The More field is one (1) bit in length, and indicates whether or
not the current attribute contains "more" than 251 octets of data.
The More field MUST be clear (0) if the Length field has value
less than 255. The More field MAY be set (1) if the Length field
has value of 255.
If the More field is set (1), it indicates that the Value field
has been fragmented across multiple RADIUS attributes. When the
More field is set (1), the attribute SHOULD have a Length field of
value 255; it MUST NOT have a length Field of value 4; there MUST
be an attribute following this one; and the next attribute MUST
have both the same Type and Extended Type. That is, multiple
fragments of the same value MUST be in order and MUST be
consecutive attributes in the packet, and the last attribute in a
packet MUST NOT have the More field set (1).
When the Length field of an attribute has value less than 255, the
More field SHOULD be clear (0).
If a client or server receives an attribute fragment with the
"More" field set (1), but for which no subsequent fragment can be
found, then the fragmented attribute is considered to be an
"invalid attribute", and handled as per Section 2.8, below.
Reserved
This field is 7 bits long, and is reserved for future use.
Implementations MUST set it to zero (0) when encoding an attribute
for sending in a packet. The contents SHOULD be ignored on
reception.
Future specifications may define additional meaning for this
field. Implementations therefore MUST NOT treat this field as
invalid if it is non-zero.
Value
This field is similar to the Value field of the Attribute format
defined in [RFC2865] Section 5. It may contain a complete set of
data (when the Length field has value less than 255), or it may
contain a fragment of data (when the More field is set).
Any interpretation of the resulting data MUST occur after the
DeKok, Alan Standards Track [Page 12]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
fragments have been reassembled. The length of the data MUST be
taken as the sum of the lengths of the fragments (i.e. Value
fields) from which it is constructed. The format of the data
SHOULD be a valid RADIUS data type.
We note that the maximum size of a fragmented attribute is limited
only by the RADIUS packet length limitation (i.e. 4096 octets, not
counting various headers and overhead). Implementations SHOULD be
able to handle fragmented attributes of 4096 octets.
This definition increases the RADIUS Attribute Type space as above,
but also provides for transport of Attributes which could contain
more than 253 octets of data.
Note that [RFC2865] Section 5 says:
If multiple Attributes with the same Type are present, the order
of
Attributes with the same Type MUST be preserved by any proxies.
The
order of Attributes of different Types is not required to be
preserved. A RADIUS server or client MUST NOT have any
dependencies
on the order of attributes of different types. A RADIUS server or
client MUST NOT require attributes of the same type to be
contiguous.
These requirements also apply to the "Long Extended Type" attribute,
including fragments. Implementations MUST be able to process non-
contiguous fragments. That is, fragments which are mixed together
with other attributes of a different Type.
2.3. TLV Data Type
We define a new data type in RADIUS, called "tlv". The "tlv" data
type is an encapsulation layer which permits the "Value" field of an
Attribute to contain new sub-Attributes. These sub-Attributes can in
turn contain "Value"s of data type TLV. This capability both extends
the attribute space, and permits "nested" attributes to be used.
This nesting can be used to encapsulate or group data into one or
more logical containers.
The "tlv" data type re-uses the RADIUS attribute format, as given
below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
DeKok, Alan Standards Track [Page 13]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
| TLV-Type | TLV-Length | TLV-Value ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
TLV-Type
The Type field is one octet. Up-to-date values of this field are
specified according to the policies and rules described in Section
10. Values of zero (0) MUST NOT be used. Values 254-255 are
"Reserved" for use by future extensions to RADIUS. The value 26
has no special meaning, and MUST NOT be treated as a Vendor
Specific attribute.
As with Extended-Type above, the TLV-Type is meaningful only
within the context defined by "Type" fields of the encapsulating
Attributes. That is, the field may be thought of as defining a
new type space of the form "Type.Extended-Type.TLV-Type". Where
TLVs are nested, the type space is of the form "Type.Extended-
Type.TLV-Type.TLV-Type", etc.
A RADIUS server MAY ignore Attributes with an unknown "TLV-Type".
A RADIUS client MAY ignore Attributes with an unknown "TLV-Type".
A RADIUS proxy SHOULD forward Attributes with an unknown "TLV-
Type" verbatim.
TLV-Length
The TLV-Length field is one octet, and indicates the length of
this TLV including the TLV-Type, TLV-Length and TLV-Value fields.
It MUST have a value between 3 and 255. If a client or server
receives a TLV with an invalid TLV-Length, then the attribute
which encapsulates that TLV MUST be considered to be an "invalid
attribute", and handled as per Section 2.8, below.
TLV-Value
The Value field is one or more octets and contains information
specific to the Attribute. The format and length of the TLV-Value
field is determined by the TLV-Type and TLV-Length fields.
The TLV-Value field SHOULD encapsulate a previously defined RADIUS
data type. Use of non-standard data types SHOULD NOT be done. We
note that the TLV-Value field MAY also contain one or more
attributes of data type "tlv", which allows for simple grouping
and multiple layers of nesting.
The TLV-Value field is limited to containing 253 or fewer octets
DeKok, Alan Standards Track [Page 14]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
of data. Specifications which require a TLV to contain more than
253 octets of data are incompatible with RADIUS, and need to be
redesigned. Specifications which require the transport of empty
Values (i.e. Length = 2) are incompatible with RADIUS, and need to
be redesigned.
The TLV-Value field MUST NOT contain data using the "Extended
Type" formats defined in this document. The base Extended
Attributes format allows for sufficient flexibility that nesting
them inside of a TLV offers little additional value.
This TLV definition is compatible with the suggested format of the
"String" field of the Vendor-Specific attribute, as defined in
[RFC2865] Section 5.26, though that specification does not discuss
nesting.
Vendors MAY use attributes of type "tlv" in any Vendor Specific
Attribute. It is RECOMMENDED to use type "tlv" for VSAs, in
preference to any other format.
If multiple TLVs with the same TLV-Type are present, the order of
TLVs with the same TLV-Type MUST be preserved by any proxies. The
order of TLVs of different TLV-Types is not required to be preserved.
A RADIUS server or client MUST NOT have any dependencies on the order
of TLVs of different TLV-Types. A RADIUS server or client MUST NOT
require TLVs of the same TLV-type to be contiguous.
The interpretation of multiple TLVs of the same TLV-Type MUST be that
of a logical "and", unless otherwise specified. That is, multiple
TLVs are interpreted as specifying a set or a list of values.
Specifications SHOULD NOT define TLVs to be interpreted as a logical
"or". Doing so would mean that a RADIUS client or server would make
an arbitrary, and non-deterministic choice among the values.
2.3.1. TLV Nesting
TLVs may contain other TLVs. When this occurs, the "container" TLV
MUST be completely filled by the "contained" TLVs. That is, the
"container" TLV-Length field MUST be exactly two (2) more than the
sum of the "contained" TLV-Length fields. If the "contained" TLVs
over-fill the "container" TLV, the "container" TLV MUST be considered
to be an "invalid attribute", and handled as described in Section
2.8, below.
The depth of TLV nesting is limited only by the restrictions on the
TLV-Length field. The limit of 253 octets of data results in a limit
of 126 levels of nesting. However, nesting depths of more than 4 are
NOT RECOMMENDED.
DeKok, Alan Standards Track [Page 15]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
2.4. EVS Data Type
We define a new data type in RADIUS, called "evs", for "Extended
Vendor-Specific". The "evs" data type is an encapsulation layer
which permits the "Value" field of an Attribute to contain a Vendor-
Id, followed by a Vendor-Type, and then vendor-defined data. This
data can in turn contain valid RADIUS data types, or any other data
as determined by the vendor.
This data type is intended use in attributes which carry Vendor-
Specific information, as is done with the Vendor-Specific Attribute
(26). It is RECOMMENDED that this data type be used by a vendor only
when the Vendor-Specific Attribute Type space has been fully
allocated.
Where [RFC2865] Section 5.26 makes a recommendation for the format of
the data following the Vendor-Id, we give a strict definition.
Experience has shown that many vendors have not followed the
[RFC2865] recommendations, leading to interoperability issues. We
hope here to give vendors sufficient flexibility as to meet their
needs, while minimizing the use of non-standard VSA formats.
The "evs" data type MAY be used in Attributes having the format of
"Extended Type" or "Long Extended Type". It MUST NOT be used in any
other Attribute definition, including standard RADIUS Attributes,
TLVs, and VSAs.
A summary of the "evs" data type format is shown below. The fields
are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vendor-Id |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vendor-Type | String ....
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Vendor-Id
The 4 octets are the Network Management Private Enterprise Code
[PEN] of the Vendor in network byte order.
Vendor-Type
The Vendor-Type field is one octet. Values are assigned at the
sole discretion of the Vendor.
DeKok, Alan Standards Track [Page 16]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
Value
The Value field is one or more octets. It SHOULD encapsulate a
previously defined RADIUS data type. Using non-standard data
types is NOT RECOMMENDED. We note that the Value field may be of
data type "tlv". However, it MUST NOT be of data type "evs", as
the use cases are unclear for one vendor delegating Attribute Type
space to another vendor.
The actual format of the information is site or application
specific, and a robust implementation SHOULD support the field as
undistinguished octets. We recognise that Vendors have complete
control over the contents and format of the Value field, while at
the same time recommending that good practices be followed.
Further codification of the range of allowed usage of this field
is outside the scope of this specification.
Note that unlike the format described in [RFC2865] Section 5.26, this
data type has no "Vendor length" field. The length of the "String"
field is implicit, and is determined by taking the "Length" of the
encapsulating RADIUS Attribute, and subtracting the length of the
attribute header (2 octets), the extended type (1 octet), the Vendor-
Id (4 octets), and the Vendor-type (1 octet). i.e. For "Extended
Type" attributes, the length of the String field is eight (8) less
than the value of the Length field. For "Long Extended Type"
attributes, the length of the String field is nine (9) less than the
value of the Length field.
2.5. Integer64 Data Type
We define a new data type in RADIUS, called "integer64", which
carries a 64-bit unsigned integer in network byte order.
This data type is intended to be used in any situation where there is
a need to have counters which can count past 2^32. The expected use
of this data type is within Accounting-Request packets, but this data
type SHOULD be used in any packet where 32-bit integers are expected
to be insufficient.
The "integer64" data type can be used in Attributes of any format,
standard space, extended attributes, TLVs, and VSAs.
A summary of the "integer64" data type format is shown below. The
fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
DeKok, Alan Standards Track [Page 17]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Attributes having data type "integer64" MUST have the relevant Length
field set to eight more than the length of the Attribute header. For
standard space Attributes and TLVs, this means that the Length field
MUST be set to ten (10). For "Extended Type" Attributes, the Length
field MUST be set to eleven (11). For "Long Extended Type"
Attributes, the Length field MUST be set to twelve (12).
2.6. Vendor-ID Field
We define the Vendor-ID field of Vendor-Specific Attributes to
encompass the entire 4 octets of the Vendor field. [RFC2865] Section
5.26 defined it to be 3 octets, with the high octet being zero. This
change has no immediate impact on RADIUS, as the maximum Private
Enterprise Code defined is still within 16 bits.
However, it is best to make advance preparations for changes in the
protocol. As such, it is RECOMMENDED that all implementations
support four (4) octets for the Vendor-ID field, instead of three
(3).
2.7. Attribute Naming and Type Identifiers
Attributes have traditionally been identified by a unique name and
number. For example, the attribute named "User-Name" has been
allocated number one (1). This scheme needs to be extended in order
to be able to refer to attributes of Extended Type, and to TLVs. It
will also be used by IANA for allocating RADIUS Attribute Type
values.
The names and identifiers given here are intended to be used only in
specifications. The system presented here may not be useful when
referring to the contents of a RADIUS packet. It imposes no
requirements on implementations, as implementations are free to
reference RADIUS Attributes via any method they choose.
2.7.1. Attribute and TLV Naming
RADIUS specifications traditionally use names consisting of one or
more words, separated by hyphens, e.g. "User-Name". However, these
names are not allocated from a registry, and there is no restriction
other than convention on their global uniqueness.
DeKok, Alan Standards Track [Page 18]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
Similarly, vendors have often used their company name as the prefix
for VSA names, though this practice is not universal. For example,
for a vendor named "Example", the name "Example-Attribute-Name"
SHOULD be used instead of "Attribute-Name". The second form can
conflict with attributes from other vendors, whereas the first form
cannot.
It is therefore RECOMMENDED that specifications give names to
Attributes which attempt to be globally unique across all RADIUS
Attributes. It is RECOMMENDED that vendors use their name as a
unique prefix for attribute names, e.g. Livingston-IP-Pool instead of
IP-Pool. It is RECOMMENDED that implementations enforce uniqueness
on names, which would otherwise lead to ambiguity and problems.
We recognise that these suggestion may sometimes be difficult to
implement in practice.
TLVs SHOULD be named with a unique prefix that is shared among
related attributes. For example, a specification that defines a set
of TLVs related to time could create attributes named "Time-Zone",
"Time-Day", "Time-Hour", "Time-Minute", etc.
2.7.2. Attribute Type Identifiers
The RADIUS Attribute Type space defines a context for a particular
"Extended-Type" field. The "Extended-Type" field allows for 256
possible type code values, with values 1 through 240 available for
allocation. We define here an identification method that uses a
"dotted number" notation similar to that used for Object Identifiers
(OIDs), formatted as "Type.Extended-Type".
For example, and attribute within the Type space of 241, having
Extended-Type of one (1), is uniquely identified as "241.1".
Similarly, an attribute within the Type space of 246, having
Extended-Type of ten (10), is uniquely identified as "246.10".
The algorithm used to create the Attribute Identifier is simply to
concatenate all of the various identification fields (e.g. Type,
Extended-Type, etc.), starting from the encapsulating attribute, down
to the final encapsulated TLV, separated by a '.' character.
2.7.3. TLV Identifiers
We can extend the Attribute reference scheme defined above for TLVs.
This is done by leveraging the "dotted number" notation. As above,
we define an additional TLV type space, within the "Extended Type"
space, by appending another "dotted number" in order to identify the
TLV. This method can be replied in sequence for nested TLVs.
DeKok, Alan Standards Track [Page 19]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
For example, let us say that "245.1" identifies RADIUS Attribute Type
245, containing an "Extended Type" of one (1), which is of type
"tlv". That attribute will contain 256 possible TLVs, one for each
value of the TLV-Type field. The first TLV-Type value of one (1) can
then be identified by appending a ".1" to the number of the
encapsulating attribute ("241.1"), to yield "241.1.1". Similarly,
the sequence "245.2.3.4" identifies RADIUS attribute 245, containing
an "Extended Type" of two (2) which is of type "tlv", which in turn
contains a TLV with TLV-Type number three (3), which in turn contains
another TLV, wth TLV-Type number four (4).
2.7.4. VSA Identifiers
There has historically been no method for numerically addressing
VSAs. The "dotted number" method defined here can also be leveraged
to create such an addressing scheme. However, as the VSAs are
completely under the control of each individual vendor, this section
provides a suggested practice, but does not define a standard of any
kind.
The Vendor-Specific Attribute has been assigned the Attribute number
26. It in turn carries a 24-bit Vendor-Id, and possibly additional
VSAs. Where the VSAs follow the [RFC2865] Section 5.26 recommended
format, a VSA can be identified as "26.Vendor-Id"."Vendor-Type".
For example, Livingston has Vendor-Id 307, and has defined an
attribute "IP-Pool" as number 6. This VSA can be uniquely identified
as 26.307.6, but it cannot be uniquely identified by name.
Note that there is no restriction on the size of the numerical values
in this notation. The Vendor-Id is a 24-bit number, and the VSA may
have been assigned from a 16-bit vendor-specific Attribute Type
space.
For example, the company USR has been allocated Vendor-Id 429, and
has defined a "Version-Id" attribute as number 32768. This VSA can
be uniquely identified as 26.429.32768, and again cannot be uniquely
identified by name.
Where a VSA is a TLV, the "dotted number" notation can be used as
above: 26.VID.VSA.TLV1.TLV2.TLV3 where "TLVn" are the numerical
values assigned by the vendor to the different nested TLVs.
2.8. Invalid Attributes
The term "invalid attribute" is new to this specification. It is
defined to mean that the Length field of an Attribute is valid (as
per [RFC2865], Section 5, top of page 25). However, the Value field
DeKok, Alan Standards Track [Page 20]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
of the attribute does not follow the format required by the data type
defined for that Attribute. e.g. an Attribute of data type "address"
which encapsulates more than four, or less than four, octets of data.
Or, an IPV6 Prefix attribute which has a Prefix value of more than
128.
While the content of these attributes is malformed, we emphasize that
the encapsulating RADIUS packet (or TLV) is well formed, and can be
correctly decoded. The existence of an "invalid attribute" in a
packet MUST NOT result in the implementation discarding the entire
packet, or treating the packet as a negative acknowledgement.
Instead, only the "invalid attribute" is treated differently.
When an implementation receives an "invalid attribute", it SHOULD be
silently discarded. If it is not discarded, it MUST NOT be handled
in the same manner as a well-formed attribute. For example,
receiving an Attribute of data type "address" containing more than
four, or less than four octets of data means that the Attribute MUST
NOT be treated as being of data type "address".
For Attributes of type "Long Extended Type", an Attribute is
considered to be an "invalid attribute" when does not match the
criteria set out in Section 2.2, above.
For Attributes of type "TLV", an Attribute is considered to be an
"invalid attribute" when the TLV-Length field is valid, but the TLV-
Value field does not match the criteria for that Attribute.
Implementations SHOULD NOT treat the "invalid attribute" property as
being transitive. That is, the encapsulating Attribute SHOULD NOT be
treated as being an "invalid attribute" if it encapsulates an
"invalid attribute".
3. Attribute Definitions
We define four (4) attributes of "Extended Type", which are allocated
from the "Reserved" Attribute Type codes of 241, 242, 243, and 244.
We also define two (2) attributes of "Long Extended Type", which are
allocated from the "Reserved" Attribute Type codes of 245 and 246.
Type Name
---- ----
241 Extended-Type-1
242 Extended-Type-2
243 Extended-Type-3
244 Extended-Type-4
245 Long-Extended-Type-1
246 Long-Extended-Type-2
DeKok, Alan Standards Track [Page 21]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
The rest of this section gives a detailed definition for each
Attribute based on the above summary.
3.1. Extended-Type-1
Description
This attribute encapsulates attributes of the "Extended Type"
format, in the RADIUS Attribute Type Space of 241.{1-255}.
A summary of the Extended-Type-1 Attribute format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Extended-Type | Value ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
241 for Extended-Type-1.
Length
>= 4
Extended-Type
The Extended-Type field is one octet. Up-to-date values of this
field are specified in the 241.{1-255} RADIUS Attribute Type
Space, according to the policies and rules described in Section
10. Further definition of this field is given in Section 2.1,
above.
Value
The Value field is one or more octets. Implementations not
supporting this specification SHOULD support the field as
undistinguished octets.
Implementations supporting this specification MUST use the
Identifier of "Type.Extended-Type" to determine the interpretation
of the Value field.
DeKok, Alan Standards Track [Page 22]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
3.2. Extended-Type-2
Description
This attribute encapsulates attributes of the "Extended Type"
format, in the RADIUS Attribute Type Space of 242.{1-255}.
A summary of the Extended-Type-2 Attribute format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Extended-Type | Value ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
242 for Extended-Type-2.
Length
>= 4
Extended-Type
The Extended-Type field is one octet. Up-to-date values of this
field are specified in the 242.{1-255} RADIUS Attribute Type
Space, according to the policies and rules described in Section
10. Further definition of this field is given in Section 2.1,
above.
Value
The Value field is one or more octets. Implementations not
supporting this specification SHOULD support the field as
undistinguished octets.
Implementations supporting this specification MUST use the
Identifier of "Type.Extended-Type" to determine the interpretation
of the Value field
3.3. Extended-Type-3
Description
This attribute encapsulates attributes of the "Extended Type"
DeKok, Alan Standards Track [Page 23]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
format, in the RADIUS Attribute Type Space of 243.{1-255}.
A summary of the Extended-Type-3 Attribute format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Extended-Type | Value ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
243 for Extended-Type-3.
Length
>= 4
Extended-Type
The Extended-Type field is one octet. Up-to-date values of this
field are specified in the 243.{1-255} RADIUS Attribute Type
Space, according to the policies and rules described in Section
10. Further definition of this field is given in Section 2.1,
above.
Value
The Value field is one or more octets. Implementations not
supporting this specification SHOULD support the field as
undistinguished octets.
Implementations supporting this specification MUST use the
Identifier of "Type.Extended-Type" to determine the interpretation
of the Value field.
3.4. Extended-Type-4
Description
This attribute encapsulates attributes of the "Extended Type"
format, in the RADIUS Attribute Type Space of 244.{1-255}.
A summary of the Extended-Type-4 Attribute format is shown below.
The fields are transmitted from left to right.
0 1 2 3
DeKok, Alan Standards Track [Page 24]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Extended-Type | Value ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
244 for Extended-Type-4.
Length
>= 4
Extended-Type
The Extended-Type field is one octet. Up-to-date values of this
field are specified in the 244.{1-255} RADIUS Attribute Type
Space, according to the policies and rules described in Section
10. Further definition of this field is given in Section 2.1,
above.
Value
The Value field is one or more octets. Implementations not
supporting this specification SHOULD support the field as
undistinguished octets.
Implementations supporting this specification MUST use the
Identifier of "Type.Extended-Type" to determine the interpretation
of the Value Field.
3.5. Long-Extended-Type-1
Description
This attribute encapsulates attributes of the "Long Extended Type"
format, in the RADIUS Attribute Type Space of 245.{1-255}.
A summary of the Long-Extended-Type-1 Attribute format is shown
below. The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Extended-Type |M| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value ...
DeKok, Alan Standards Track [Page 25]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
245 for Long-Extended-Type-1
Length
>= 5
Extended-Type
The Extended-Type field is one octet. Up-to-date values of this
field are specified in the 245.{1-255} RADIUS Attribute Type
Space, according to the policies and rules described in Section
10. Further definition of this field is given in Section 2.1,
above.
M (More)
The More field is one (1) bit in length, and indicates whether or
not the current attribute contains "more" than 251 octets of data.
Further definition of this field is given in Section 2.2, above.
Reserved
This field is 7 bits long, and is reserved for future use.
Implementations MUST set it to zero (0) when encoding an attribute
for sending in a packet. The contents SHOULD be ignored on
reception.
Value
The Value field is one or more octets. Implementations not
supporting this specification SHOULD support the field as
undistinguished octets.
Implementations supporting this specification MUST use the
Identifier of "Type.Extended-Type" to determine the interpretation
of the Value field.
3.6. Long-Extended-Type-2
Description
This attribute encapsulates attributes of the "Long Extended Type"
format, in the RADIUS Attribute Type Space of 246.{1-255}.
DeKok, Alan Standards Track [Page 26]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
A summary of the Long-Extended-Type-2 Attribute format is shown
below. The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Extended-Type |M| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
246 for Long-Extended-Type-2
Length
>= 5
Extended-Type
The Extended-Type field is one octet. Up-to-date values of this
field are specified in the 246.{1-255} RADIUS Attribute Type
Space, according to the policies and rules described in Section
10. Further definition of this field is given in Section 2.1,
above.
M (More)
The More field is one (1) bit in length, and indicates whether or
not the current attribute contains "more" than 251 octets of data.
Further definition of this field is given in Section 2.2, above.
Reserved
This field is 7 bits long, and is reserved for future use.
Implementations MUST set it to zero (0) when encoding an attribute
for sending in a packet. The contents SHOULD be ignored on
reception.
Value
The Value field is one or more octets. Implementations not
supporting this specification SHOULD support the field as
undistinguished octets.
Implementations supporting this specification MUST use the
Identifier of "Type.Extended-Type" to determine the interpretation
DeKok, Alan Standards Track [Page 27]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
of the Value field.
4. Vendor Specific Attributes
We define six new attributes which can carry Vendor Specific
information. We define four (4) attributes of the "Extended Type"
format, with Type codes (241.26, 242.26, 243.26, 244.26), using the
"evs" data type. We also define two (2) attributes using "Long
Extended Type" format, with Type codes (245.26, 246.26), which are of
the "evs" data type.
Type.Extended-Type Name
------------------ ----
241.26 Extended-Vendor-Specific-1
242.26 Extended-Vendor-Specific-2
243.26 Extended-Vendor-Specific-3
244.26 Extended-Vendor-Specific-4
245.26 Extended-Vendor-Specific-5
246.26 Extended-Vendor-Specific-6
The rest of this section gives a detailed definition for each
Attribute based on the above summary.
4.1. Extended-Vendor-Specific-1
Description
This attribute defines a RADIUS Type Code of 241.26, using the
"evs" data type.
A summary of the Extended-Vendor-Specific-1 Attribute format is shown
below. The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Extended-Type | Vendor-Id ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... Vendor-Id (cont) | Vendor-Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value ....
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type.Extended-Type
241.26 for Extended-Vendor-Specific-1
Length
DeKok, Alan Standards Track [Page 28]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
>= 9
Vendor-Id
The 4 octets are the Network Management Private Enterprise Code
[PEN] of the Vendor in network byte order.
Vendor-Type
The Vendor-Type field is one octet. Values are assigned at the
sole discretion of the Vendor.
Value
The Value field is one or more octets. The actual format of the
information is site or application specific, and a robust
implementation SHOULD support the field as undistinguished octets.
The codification of the range of allowed usage of this field is
outside the scope of this specification.
The length of the Value field is eight (8) less then the value of
the Length field.
Implementations supporting this specification MUST use the
Identifier of "Type.Extended-Type.Vendor-Id.Vendor-Type" to
determine the interpretation of the Value field.
4.2. Extended-Vendor-Specific-2
Description
This attribute defines a RADIUS Type Code of 242.26, using the
"evs" data type.
A summary of the Extended-Vendor-Specific-2 Attribute format is shown
below. The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Extended-Type | Vendor-Id ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... Vendor-Id (cont) | Vendor-Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value ....
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
DeKok, Alan Standards Track [Page 29]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
Type.Extended-Type
242.26 for Extended-Vendor-Specific-2
Length
>= 9
Vendor-Id
The 4 octets are the Network Management Private Enterprise Code
[PEN] of the Vendor in network byte order.
Vendor-Type
The Vendor-Type field is one octet. Values are assigned at the
sole discretion of the Vendor.
Value
The Value field is one or more octets. The actual format of the
information is site or application specific, and a robust
implementation SHOULD support the field as undistinguished octets.
The codification of the range of allowed usage of this field is
outside the scope of this specification.
The length of the Value field is eight (8) less then the value of
the Length field.
Implementations supporting this specification MUST use the
Identifier of "Type.Extended-Type.Vendor-Id.Vendor-Type" to
determine the interpretation of the Value field.
4.3. Extended-Vendor-Specific-3
Description
This attribute defines a RADIUS Type Code of 243.26, using the
"evs" data type.
A summary of the Extended-Vendor-Specific-3 Attribute format is shown
below. The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Extended-Type | Vendor-Id ...
DeKok, Alan Standards Track [Page 30]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... Vendor-Id (cont) | Vendor-Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value ....
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type.Extended-Type
243.26 for Extended-Vendor-Specific-3
Length
>= 9
Vendor-Id
The 4 octets are the Network Management Private Enterprise Code
[PEN] of the Vendor in network byte order.
Vendor-Type
The Vendor-Type field is one octet. Values are assigned at the
sole discretion of the Vendor.
Value
The Value field is one or more octets. The actual format of the
information is site or application specific, and a robust
implementation SHOULD support the field as undistinguished octets.
The codification of the range of allowed usage of this field is
outside the scope of this specification.
The length of the Value field is eight (8) less then the value of
the Length field.
Implementations supporting this specification MUST use the
Identifier of "Type.Extended-Type.Vendor-Id.Vendor-Type" to
determine the interpretation of the Value field.
4.4. Extended-Vendor-Specific-4
Description
This attribute defines a RADIUS Type Code of 244.26, using the
"evs" data type.
A summary of the Extended-Vendor-Specific-3 Attribute format is shown
DeKok, Alan Standards Track [Page 31]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
below. The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Extended-Type | Vendor-Id ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... Vendor-Id (cont) | Vendor-Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value ....
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type.Extended-Type
244.26 for Extended-Vendor-Specific-4
Length
>= 9
Vendor-Id
The 4 octets are the Network Management Private Enterprise Code
[PEN] of the Vendor in network byte order.
Vendor-Type
The Vendor-Type field is one octet. Values are assigned at the
sole discretion of the Vendor.
Value
The Value field is one or more octets. The actual format of the
information is site or application specific, and a robust
implementation SHOULD support the field as undistinguished octets.
The codification of the range of allowed usage of this field is
outside the scope of this specification.
The length of the Value field is eight (8) less then the value of
the Length field.
Implementations supporting this specification MUST use the
Identifier of "Type.Extended-Type.Vendor-Id.Vendor-Type" to
determine the interpretation of the Value field.
DeKok, Alan Standards Track [Page 32]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
4.5. Extended-Vendor-Specific-5
Description
This attribute defines a RADIUS Type Code of 245.26, using the
"evs" data type.
A summary of the Extended-Vendor-Specific-5 Attribute format is shown
below. The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Extended-Type |M| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vendor-Id |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vendor-Type | Value ....
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type.Extended-Type
245.26 for Extended-Vendor-Specific-5
Length
>= 10 (first fragment)
>= 5 (subsequent fragments)
When a VSA is fragmented across multiple Attributes, only the
first Attribute contains the Vendor-Id and Vendor-Type fields.
Subsequent Attributes contain fragments of the Value field only.
M (More)
The More field is one (1) bit in length, and indicates whether or
not the current attribute contains "more" than 251 octets of data.
Further definition of this field is given in Section 2.2, above.
Reserved
This field is 7 bits long, and is reserved for future use.
Implementations MUST set it to zero (0) when encoding an attribute
for sending in a packet. The contents SHOULD be ignored on
reception.
Vendor-Id
DeKok, Alan Standards Track [Page 33]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
The 4 octets are the Network Management Private Enterprise Code
[PEN] of the Vendor in network byte order.
Vendor-Type
The Vendor-Type field is one octet. Values are assigned at the
sole discretion of the Vendor.
Value
The Value field is one or more octets. The actual format of the
information is site or application specific, and a robust
implementation SHOULD support the field as undistinguished octets.
The codification of the range of allowed usage of this field is
outside the scope of this specification.
Implementations supporting this specification MUST use the
Identifier of "Type.Extended-Type.Vendor-Id.Vendor-Type" to
determine the interpretation of the Value field.
4.6. Extended-Vendor-Specific-6
Description
This attribute defines a RADIUS Type Code of 246.26, using the
"evs" data type.
A summary of the Extended-Vendor-Specific-6 Attribute format is shown
below. The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Extended-Type |M| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vendor-Id |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Vendor-Type | Value ....
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type.Extended-Type
246.26 for Extended-Vendor-Specific-6
Length
>= 10 (first fragment)
DeKok, Alan Standards Track [Page 34]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
>= 5 (subsequent fragments)
When a VSA is fragmented across multiple Attributes, only the
first Attribute contains the Vendor-Id and Vendor-Type fields.
Subsequent Attributes contain fragments of the Value field only.
M (More)
The More field is one (1) bit in length, and indicates whether or
not the current attribute contains "more" than 251 octets of data.
Further definition of this field is given in Section 2.2, above.
Reserved
This field is 7 bits long, and is reserved for future use.
Implementations MUST set it to zero (0) when encoding an attribute
for sending in a packet. The contents SHOULD be ignored on
reception.
Vendor-Id
The 4 octets are the Network Management Private Enterprise Code
[PEN] of the Vendor in network byte order.
Vendor-Type
The Vendor-Type field is one octet. Values are assigned at the
sole discretion of the Vendor.
Value
The Value field is one or more octets. The actual format of the
information is site or application specific, and a robust
implementation SHOULD support the field as undistinguished octets.
The codification of the range of allowed usage of this field is
outside the scope of this specification.
Implementations supporting this specification MUST use the
Identifier of "Type.Extended-Type.Vendor-Id.Vendor-Type" to
determine the interpretation of the Value field.
5. Compatibility with traditional RADIUS
There are a number of potential compatibility issues with traditional
RADIUS, as defined in [RFC6158] and earlier. This section describes
them.
DeKok, Alan Standards Track [Page 35]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
5.1. Attribute Allocation
Some vendors have used Attribute Type codes from the "Reserved"
space, as part of vendor-defined dictionaries. This practice is
considered anti-social behavior, as noted in [RFC6158]. These vendor
definitions conflict with the attributes in the RADIUS Attribute Type
space. The conflicting definitions may make it difficult for
implementations to support both those Vendor Attributes, and the new
Extended Attribute formats.
We RECOMMEND that RADIUS client and server implementations delete all
references to these improperly defined attributes. Failing that, we
RECOMMEND that RADIUS server implementations have a per-client
configurable flag which indicates which type of attributes are being
sent from the client. If the flag is set to "Non-Standard
Attributes", the conflicting attributes can be interpreted as being
improperly defined Vendor Specific Attributes. If the flag is set the
"IETF Attributes", the attributes MUST be interpreted as being of the
Extended Attributes format. The default SHOULD be to interpret the
attributes as being of the Extended Attributes format.
Other methods of determining how to decode the attributes into a
"correct" form are NOT RECOMMENDED. Those methods are likely to be
fragile and prone to error.
We RECOMMEND that RADIUS server implementations re-use the above flag
to determine which type of attributes to send in a reply message. If
the request is expected to contain the improperly defined attributes,
the reply SHOULD NOT contain Extended Attributes. If the request is
expected to contain Extended Attributes, the reply MUST NOT contain
the improper Attributes.
RADIUS clients will have fewer issues than servers. Clients MUST NOT
send improperly defined Attributes in a request. For replies,
clients MUST interpret attributes as being of the Extended Attributes
format, instead of the improper definitions. These requirements
impose no change in the RADIUS specifications, as such usage by
vendors has always been in conflict with the standard requirements
and the standards process.
Existing clients that send these improperly defined attributes
usually have a configuration setting which can disable this behavior.
We RECOMMEND that vendors ship products with the default set to
"disabled". We RECOMMEND that administrators set this flag to
"disabled" on all equipment that they manage.
DeKok, Alan Standards Track [Page 36]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
5.2. Proxy Servers
RADIUS Proxy servers will need to forward Attributes having the new
format, even if they do not implement support for the encoding and
decoding of those attributes. We remind implementors of the
following text in [RFC2865] Section 2.3:
The forwarding server MUST NOT change the order of any attributes
of the same type, including Proxy-State.
This requirement solves some of the issues related to proxying of the
new format, but not all. The reason is that proxy servers are
permitted to examine the contents of the packets that they forward.
Many proxy implementations not only examine the attributes, but they
refuse to forward attributes which they do not understand (i.e.
attributes for which they have no local dictionary definitions).
This practice is NOT RECOMMENDED. Proxy servers SHOULD forward
attributes, even ones which they do not understand, or which are not
in a local dictionary. When forwarded, these attributes SHOULD be
sent verbatim, with no modifications or changes. This requirement
includes "invalid attributes", as there may be some other system in
the network which understands them.
The only exception to this recommendation is when local site policy
dictates that filtering of attributes has to occur. For example, a
filter at a visited network may require removal of certain
authorization rules which apply to the home network, but not to the
visited network. This filtering can sometimes be done even when the
contents of the attributes are unknown, such as when all Vendor-
Specific Attributes are designated for removal.
As seen in [EDUROAM] many proxies do not follow these practices for
unknown Attributes. Some proxies filter out unknown attributes or
attributes which have unexpected lengths (24%, 17/70), some truncate
the attributes to the "expected" length (11%, 8/70), some discard the
request entirely (1%, 1/70), with the rest (63%, 44/70) following the
recommended practice of passing the attributes verbatim. It will be
difficult to widely use the Extended Attributes format until all non-
conformant proxies are fixed. We therefore RECOMMEND that all
proxies which do not support the Extended Attributes (241 through
246) define them as being of data type "string", and delete all other
local definitions for those attributes.
This last change should enable wider usage of the Extended Attributes
format.
DeKok, Alan Standards Track [Page 37]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
6. Guidelines
This specification proposes a number of changes to RADIUS, and
therefore requires a set of guidelines, as has been done in
[RFC6158].
6.1. Updates to RFC 6158
This specification updates [RFC6158] by adding the data types "evs",
"tlv" and "integer64"; defining them to be "basic" data types; and
permitting their use subject to the restrictions outlined below.
The recommendations for the use of the new data types and attribute
formats are given below. All other recommendations given in
[RFC6158] are unchanged.
6.2. Guidelines for Simple Data Types
[RFC6158] Section A.2.1 says in part:
* Unsigned integers of size other than 32 bits.
SHOULD be replaced by an unsigned integer of 32 bits. There is
insufficient justification to define a new size of integer.
We update that specification to permit unsigned integers of 64 bits,
for the reasons defined above in Section 2.5. The updated text is as
follows:
* Unsigned integers of size other than 32 or 64 bits.
SHOULD be replaced by an unsigned integer of 32 or 64 bits.
There is insufficient justification to define a new size
of integer.
That section later continues with the following list item:
* Nested attribute-value pairs (AVPs).
Attributes should be defined in a flat typespace.
We update that specification to permit nested TLVs, as defined in
this document:
* Nested attribute-value pairs (AVPs) using the extended
attribute format MAY be used. All other nested AVP or TLV
formats MUST NOT be used.
DeKok, Alan Standards Track [Page 38]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
6.3. Guidelines for Complex Data Types
[RFC6158] Section 2.1 says:
Complex data types MAY be used in situations where they reduce
complexity in non-RADIUS systems or where using the basic data
types
would be awkward (such as where grouping would be required in
order
to link related attributes).
Since the extended attribute format allows for grouping of complex
types via TLVs, the guidelines for complex data types need to be
updated as follows:
Complex data types MAY be used where they reduce complexity in
non-RADIUS systems, though this practice is NOT RECOMMENDED. The
complex data type exceptions of [RFC6158] Section 3.2.4 still
apply. In all other situations, complex data types MUST NOT be
used. Instead, complex data types MUST be decomposed into TLVs,
using the extended attribute format.
The checklist in Appendix A.2.2 is similarly updated to add a new
requirement at the top of that section,
Does the attribute:
* define a complex type which can be represented via TLVs?
If so, this data type MUST be represented via TLVs.
Note that this requirement does not over-ride Section A.1, which
permits the transport of complex types in certain situations.
6.4. Guidelines For the New Types
We recommend the following guidelines when designing attributes using
the new format. The items listed below are not exhaustive. As
experience is gained with the new formats, later specifications may
define additional guidelines.
* The data type "evs" MUST NOT be used for standard RADIUS
Attributes, or for TLVs, or for VSAs.
* The data type "tlv" SHOULD NOT be used for standard RADIUS
attributes. While its use is NOT RECOMMENDED by [RFC6158], this
specification updates [RFC6158] to permit the "tlv" data type in
DeKok, Alan Standards Track [Page 39]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
attributes using the Extended-Type format.
* [RFC2866] "tagged" attributes MUST NOT be defined in the
Extended-Type space. The "tlv" data type should be used instead to
group attributes.
* The "integer64" data type MAY be used in any RADIUS attribute.
The use of 64-bit integers is NOT RECOMMENDED by [RFC6158], but
their utility is now evident.
* Any attribute which is allocated from the Type spaces of 245.* or
246.*, of data type "text", "string", or "tlv" can end up carrying
more than 251 octets of data, up to the maximum RADIUS packet
length (~4096 octets). Specifications defining such attributes
SHOULD define a maximum length.
* For all other circumstances, the guidelines in [RFC6158] MUST
be followed.
6.5. Allocation Request Guidelines
The following items give guidelines for allocation requests made in a
RADIUS specification.
* Discretion is RECOMMENDED when requesting allocation of attributes.
The new space is much larger than the old one, but it is not
infinite.
* Specifications which allocate many attributes MUST NOT request that
allocation be made from from the standard space. That space is
under allocation pressure, and the extended space is more suitable
for large allocations.
* Specifications which allocate many related attributes SHOULD define
one or more TLVs to contain related attributes.
* Specifications should not request allocation from a specific space.
The IANA considerations given in Section 9, below, should be
sufficient for attribute allocation.
* Specifications of an attribute which encodes 252 octets or less
of data MAY request allocation from the exended space, using
format "Extended Type"
* Specifications of an attribute which always encode less than 253
octets of data MUST NOT request allocation from the long extended
space. The standard space, or the short extended space MUST be
DeKok, Alan Standards Track [Page 40]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
used instead.
* Specifications of an attribute which encodes 253 octets or more of
data MUST request allocation from the long extended space.
* When the extended space is nearing exhaustion, a new specification
SHOULD be written which requests allocation of one or more RADIUS
Attributes from the "Reserved" portion of the standard space,
values 247-255, using an appropriate format ("Extended Type", or
"Long Extended Type")
6.6. TLV Guidelines
The following items give guidelines for specifications using TLVs.
* when multiple attributes are intended to be grouped or managed
together, the use of TLVs to group related attributes is
RECOMMENDED.
* more than 4 layers (depth) of TLV nesting is NOT RECOMMENDED.
* Interpretation of an attribute depends only on its type
definition (e.g. Type.Extended-Type.TLV-Type), and
not on its encoding or location in the RADIUS packet.
* Where a group of TLVs is strictly defined, and not expected to
change, and and totals less than 247 octets of data, they SHOULD
request allocation from the Type spaces of 241.*, 242.*, 243.*, or
244.*.
* Where a group of TLVs is loosely defined, or is expected to change,
they SHOULD request allocation from the Type spaces of 245.* or
246.*.
6.7. Implementation Guidelines
* RADIUS client implementations SHOULD support this specification,
in order to permit the easy deployment of specifications using
the changes defined herein.
* RADIUS server implementations SHOULD support this specification,
in order to permit the easy deployment of specifications using
the changes defined herein.
* RADIUS proxy servers MUST follow the specifications in section 5.2
DeKok, Alan Standards Track [Page 41]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
6.8. Vendor Guidelines
* Vendors SHOULD use the existing Vendor-Specific Attribute Type
space in preference to the new Extended-Vendor-Specific
attributes, as this specification may take time to become widely
deployed.
* Vendors SHOULD implement this specification. The changes to
RADIUS are relatively small, and are likely to quickly be used
in new specifications.
7. Rationale for This Design
The path to extending the RADIUS protocol has been long and arduous.
A number of proposals have been made and discarded by the RADEXT
working group. These proposals have been judged to be either too
bulky, too complex, too simple, or to be unworkable in practice. We
do not otherwise explain here why earlier proposals did not obtain
working group consensus.
The changes outlined here have the benefit of being simple, as the
"Extended Type" format requires only a one octet change to the
Attribute format. The downside is that the "Long Extended Type"
format is awkward, and the 7 Reserved bits will likey never be used
for anything.
7.1. Attribute Audit
An audit of almost five thousand publicly available attributes
[ATTR], shows the statistics summarized below. The attributes include
over 100 Vendor dictionaries, along with the IANA assigned
attributes:
Count Data Type
----- ---------
2257 integer
1762 text
273 IPv4 Address
225 string
96 other data types
35 IPv6 Address
18 date
10 integer64
4 Interface Id
3 IPv6 Prefix
4683 Total
DeKok, Alan Standards Track [Page 42]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
The entries in the "Data Type" column are data types recommended by
[RFC6158], along with "integer64". The "other data types" row
encompasses all other data types, including complex data types and
data types transporting opaque data.
We see that over half of the attributes encode less than 16 octets of
data. It is therefore important to have an extension mechanism which
adds as little as possible to the size of these attributes. Another
result is that the overwhelming majority of attributes use simple
data types.
Of the attributes defined above, 177 were declared as being inside of
a TLV. This is approximately 4% of the total. We did not
investigate whether additional attributes were defined in a flat name
space, but could have been defined as being inside of a TLV. We
expect that the number could be as high as 10% of attributes.
Manual inspection of the dictionaries shows that approximately 20 (or
0.5%) attributes have the ability to transport more than 253 octets
of data. These attributes are divided between VSAs, and a small
number of standard Attributes such as EAP-Message.
The results of this audit and analysis is reflected in the design of
the extended attributes. The extended format has minimal overhead,
it permits TLVs, and it has support for "long" attributes.
8. Diameter Considerations
The attribute formats defined in this specification need to be
transported in Diameter. While Diameter supports attributes longer
than 253 octets and grouped attributes, we do not use that
functionality here. Instead, we define the simplest possible
encapsulation method.
The new formats MUST be treated the same as traditional RADIUS
attributes when converting from RADIUS to Diameter, or vice versa.
That is, the new attribute space is not converted to any "extended"
Diameter attribute space. Fragmented attributes are not converted to
a single long Diameter attribute. The new EVS data types are not
converted to Diameter attributes with the "V" bit set.
In short, this document mandates no changes for existing RADIUS to
Diameter, or Diameter to RADIUS gateways.
9. Examples
A few examples are presented here in order to illustrate the encoding
of the new attribute formats. These examples are not intended to be
DeKok, Alan Standards Track [Page 43]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
exhaustive, as many others are possible. For simplicity, we do not
show complete packets, only attributes.
The examples are given using a domain-specific language implemented
by the program given in Appendix A. The language is line oriented,
and composed of a sequence of lines matching the grammar ([RFC5234])
given below:
Identifier = 1*DIGIT *( "." 1*DIGIT )
HEXCHAR = HEXDIG HEXDIG
STRING = DQUOTE 1*CHAR DQUOTE
TLV = "{" 1*DIGIT DATA "}"
DATA = 1*HEXCHAR / 1*TLV / STRING
LINE = Identifier DATA
The progam has additional restrictions on its input that are not
reflected in the above grammar. For example, the portions of the
Identifier which refer to Type and Extended-Type are limited to
values between 1 and 255. We trust that the source code in Appendix
A is clear, and that these restrictions do not negatively affect the
comprehensability of the examples.
The program reads the input text, and interprets it as a set of
instructions to create RADIUS Attributes. It then prints the hex
encoding of those attributes. It implements the minimum set of
functionality which achieves that goal. This minimalism means that
it does not use attribute dictionaries; it does not implement support
for RADIUS data types; it can be used to encode attributes with
invalid data fields; and there is no requirement for consistency from
one example to the next. For example, it can be used to encode a
User-Name attribute which contains non-UTF8 data, or a Framed-IP-
Address which contains 253 octets of ASCII data. As a result, it
MUST NOT be used to create RADIUS Attributes for transport in a
RADIUS message.
However, the program correctly encodes the RADIUS attribute fields of
"Type", "Length", "Extended-Type", "More", "Reserved", "Vendor-Id",
"Vendor-Type", and "Vendor-Length". It encodes RADIUS attribute data
types "evs" and TLV. It can therefore be used to encode example
attributes from inputs which are humanly readable.
We do not give examples of "malformed" or "invalid attributes". We
also note that the examples show format, rather than consistent
DeKok, Alan Standards Track [Page 44]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
meaning. A particular Attribute Type code may be used to demonstrate
two different formats. In real specifications, attributes have a
static definitions based on their type code.
The examples given below are strictly for demonstration purposes
only, and do not provide a standard of any kind.
9.1. Extended Type
The following are a series of examples of the "Extended Type" format.
Attribute encapsulating textual data.
241.1 "bob"
-> f1 06 01 62 6f 62
Attribute encapsulating a TLV with TLV-Type of one (1).
241.2 { 1 23 45 }
-> f1 07 02 01 04 23 45
Attribute encapsulating two TLVs, one after the other.
241.2 { 1 23 45 } { 2 67 89 }
-> f1 0b 02 01 04 23 45 02 04 67 89
Attribute encapsulating two TLVs, where the second TLV is itself
encapsulating a TLV.
241.2 { 1 23 45 } { 3 { 1 ab cd } }
-> f1 0d 02 01 04 23 45 03 06 01 04 ab cd
Attribute encapsulating two TLVs, where the second TLV is itself
encapsulating two TLVs.
241.2 { 1 23 45 } { 3 { 1 ab cd } { 2 "foo" } }
-> f1 12 02 01 04 23 45 03 0b 01 04 ab cd 02 05 66 6f 6f
Attribute encapsulating a TLV, which in turn encapsulates a TLV,
to a depth of 5 nestings.
241.1 { 1 { 2 { 3 { 4 { 5 cd ef } } } } }
-> f1 0f 01 01 0c 02 0a 03 08 04 06 05 04 cd ef
Attribute encapsulating an extended Vendor Specific attribute,
with Vendor-Id of 1, and Vendor-Type of 4, which in turn
encapsulates textual data.
DeKok, Alan Standards Track [Page 45]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
241.26.1.4 "test"
-> f1 0c 1a 00 00 00 01 04 74 65 73 74
Attribute encapsulating an extended Vendor Specific attribute, with
Vendor-Id of 1, and Vendor-Type of 5, which in turn encapsulates
a TLV with TLV-Type of 3, which encapsulates textual data.
241.26.1.5 { 3 "test" }
-> f1 0e 1a 00 00 00 01 05 03 06 74 65 73 74
9.2. Long Extended Type
The following are a series of examples of the "Long Extended Type"
format.
Attribute encapsulating textual data.
245.1 "bob"
-> f5 07 01 00 62 6f 62
Attribute encapsulating a TLV with TLV-Type of one (1).
245.2 { 1 23 45 }
-> f5 08 02 00 01 04 23 45
Attribute encapsulating two TLVs, one after the other.
245.2 { 1 23 45 } { 2 67 89 }
-> f5 0c 02 00 01 04 23 45 02 04 67 89
Attribute encapsulating two TLVs, where the second TLV is itself
encapsulating a TLV.
245.2 { 1 23 45 } { 3 { 1 ab cd } }
-> f5 0e 02 00 01 04 23 45 03 06 01 04 ab cd
Attribute encapsulating two TLVs, where the second TLV is itself
encapsulating two TLVs.
245.2 { 1 23 45 } { 3 { 1 ab cd } { 2 "foo" } }
-> f5 13 02 00 01 04 23 45 03 0b 01 04 ab cd 02 05 66 6f 6f
Attribute encapsulating a TLV, which in turn encapsulates a TLV,
to a depth of 5 nestings.
245.1 { 1 { 2 { 3 { 4 { 5 cd ef } } } } }
-> f5 10 01 00 01 0c 02 0a 03 08 04 06 05 04 cd ef
DeKok, Alan Standards Track [Page 46]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
Attribute encapsulating an extended Vendor Specific attribute,
with Vendor-Id of 1, and Vendor-Type of 4, which in turn
encapsulates textual data.
245.26.1.4 "test"
-> f5 0d 1a 00 00 00 00 01 04 74 65 73 74
Attribute encapsulating an extended Vendor Specific attribute,
with Vendor-Id of 1, and Vendor-Type of 5, which in turn
encapsulates a TLV with TLV-Type of 3, which encapsulates
textual data.
245.26.1.5 { 3 "test" }
-> f5 0f 1a 00 00 00 00 01 05 03 06 74 65 73 74
Attribute encapsulating more than 251 octets of data. The "Data"
portions are indented for readability.
245.4 aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
aaaaaaaaaaaaaaaaaaabbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbcccccccccccccccccccc
cccccccccc
-> f5 ff 04 80 aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
aa aa aa aa aa aa aa aa aa ab bb bb bb bb bb bb bb bb bb bb
bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb
bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb
bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb
bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb
bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb
bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb f5 13 04 00 cc
cc cc cc cc cc cc cc cc cc cc cc cc cc cc
Attribute encapsulating an extended Vendor Specific attribute,
with Vendor-Id of 1, and Vendor-Type of 6, which in turn
encapsulates more than 251 octets of data.
As the VSA encapsulates more than 251 octets of data, it is
DeKok, Alan Standards Track [Page 47]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
split into two RADIUS attributes. The first attribute has the
More field set, and carries the Vendor-Id and Vendor-Type.
The second attribute has the More field clear, and carries
the rest of the data portion of the VSA. Note that the second
attribute does not include the Vendor-Id ad Vendor-Type fields.
The "Data" portions are indented for readability.
245.26.1.6 aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
aaaaaaaaaaaaaaaaaaaaaaaaaabbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbccccccccccccc
ccccccccccccccccc
-> f5 ff 1a 80 00 00 00 01 06 aa aa aa aa aa aa aa aa aa aa aa
aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
aa aa aa aa aa aa aa aa aa aa aa aa aa aa ab bb bb bb bb bb
bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb
bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb
bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb
bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb
bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb
bb bb bb bb bb bb bb bb bb bb bb bb bb bb bb f5 18 1a 00 bb
bb bb bb bb cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
10. IANA Considerations
This document updates [RFC3575] in that it adds new IANA
considerations for RADIUS Attributes. These considerations modify
and extend the IANA considerations for RADIUS, rather than replacing
them.
The IANA considerations of this document are limited to the "RADIUS
Attribute Types" registry. Some Attribute Type values which were
previously marked "Reserved" are now allocated, and the registry is
extended from a simple 8-bit array to a tree-like structure, up to a
maximum depth of 125 nodes. Detailed instructions are given below.
DeKok, Alan Standards Track [Page 48]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
10.1. Attribute Allocations
IANA is requested to move the following Attribute Type values from
"Reserved", to "Allocated", with the corresponding names:
* 241 Extended-Type-1
* 242 Extended-Type-2
* 243 Extended-Type-3
* 244 Extended-Type-4
* 245 Long-Extended-Type-1
* 246 Long-Extended-Type-2
These values serve as an encapsulation layer for the new RADIUS
Attribute Type tree.
10.2. RADIUS Attribute Type Tree
Each of the Attribute Type values allocated above extends the "RADIUS
Attribute Types" to an N-ary tree, via a "dotted number" notation.
Allocation of an Attribute Type value "TYPE" using the new Extended
type format results in allocation of 255 new Attribute Type values,
of format "TYPE.1" through "TYPE.255". The value zero "TYPE.0" is not
used. Value twenty-six (26) is assigned as "Extended-Vendor-
Specific-*". Values "TYPE.241" through "TYPE.255" are marked
"Reserved". All other values are "Unassigned".
The initial set of Attribute Type values and names assigned by this
document is given below.
* 241 Extended-Attribute-1
* 241.{1-25} Unassigned
* 241.26 Extended-Vendor-Specific-1
* 241.{27-240} Unassigned
* 241.{241-255} Reserved
* 242 Extended-Attribute-2
* 242.{1-25} Unassigned
* 242.26 Extended-Vendor-Specific-2
* 242.{27-240} Unassigned
* 243 Extended-Attribute-3
* 242.{241-255} Reserved
* 243.{1-25} Unassigned
* 243.26 Extended-Vendor-Specific-3
* 243.{27-240} Unassigned
* 243.{241-255} Reserved
* 244 Extended-Attribute-4
* 244.{1-25} Unassigned
* 244.26 Extended-Vendor-Specific-4
* 244.{27-240} Unassigned
DeKok, Alan Standards Track [Page 49]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
* 244.{241-255} Reserved
* 245 Extended-Attribute-5
* 245.{1-25} Unassigned
* 245.26 Extended-Vendor-Specific-5
* 245.{27-240} Unassigned
* 245.{241-255} Reserved
* 246 Extended-Attribute-6
* 246.{1-25} Unassigned
* 245.26 Extended-Vendor-Specific-6
* 246.{27-240} Unassigned
* 246.{241-255} Reserved
As per [RFC5226], the values marked "Unassigned" above are available
via for assignment by IANA in future RADIUS specifications. The
values marked "Reserved" are reserved for future use.
The Extended-Vendor-Specific spaces (TYPE.26) are for Private Use,
and allocations are not managed by IANA.
Allocation of Reserved entries in the extended space requires
Standards Action.
All other allocations in the extended space require IETF Review.
10.3. Allocation Instructions
This section defines what actions IANA needs to take when allocating
new attributes. Different actions are required when allocating
attributes from the standard space, attributes of Extended Type
format, attributes of the "Long Extended Type" format, perferential
allocations, attributes of data type TLV, attributes within a TLV,
and attributes of other data types.
10.3.1. Requested Allocation from the Standard Space
Specifications can request allocation of an Attribute from within the
standard space (e.g. Attribute Type Codes 1 through 255), subject to
the considerations of [RFC3575] and this document.
10.3.2. Requested Allocation from the short extended space
Specifications can request allocation of an Attribute which requires
the format Extended Type, by specifying the short extended space In
that case, IANA should assign the lowest Unassigned number from the
Attribute Type space with the relevant format.
DeKok, Alan Standards Track [Page 50]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
10.3.3. Requested Allocation from the long extended space
Specifications can request allocation of an Attribute which requires
the format "Long Extended Type", by specifying the extended space
(long). In that case, IANA should assign the lowest Unassigned
number from the Attribute Type space with the relevant format.
10.3.4. Allocation Preferences
Specifications which make no request for allocation from a specific
Type Space should have Attributes allocated using the following
criteria:
* when the standard space has no more Unassigned attributes,
all allocations should be performed from the extended space.
* specifications which allocate a small number of attributes
(i.e. less than ten) should have all allocations made from
the standard space.
* specifications which would allocate a large percentage of the
remaining standard space attributes should have all allocations
made from the extended space.
* specifications which request allocation of an attribute of
data type TLV should have that attribute allocated from the
extended space.
* specifications which request allocation of an attribute
which can transport 253 or more octets of data should have
that attribute allocated from within the long extended space,
We note that Section 6.5, above requires specifications to
request this allocation.
There is otherwise no requirement that all attributes within a
specification be allocated from one type space or another.
Specifications can simultaneously allocate attributes from both the
standard space and the extended space.
10.3.5. Extending the Type Space via TLV Data Type
When specifications request allocation of an attribute of data type
"tlv", that allocation extends the Attribute Type Tree by one more
level. Allocation of an Attribute Type value "TYPE.TLV", with Data
Type TLV, results in allocation of 255 new Attribute Type values, of
format "TYPE.TLV.1" through "TYPE.TLV.255". The value zero "VALUE.0"
is not used. Values 254-255 are marked "Reserved". All other values
DeKok, Alan Standards Track [Page 51]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
are "Unassigned". Value 26 has no special meaning.
For example, if a new attribute "Example-TLV" of data type "tlv" is
assigned the identifier "245.1", then the extended tree will be
allocated as below:
* 245.1 Example-TLV
* 245.1.{1-253} Unassigned
* 245.1.{254-255} Reserved
Note that this example does not define an "Example-TLV" attribute.
The Attribute Type Tree can be extended multiple levels in one
specification when the specification requests allocation of nested
TLVs, as discussed below.
10.3.6. Allocation within a TLV
Specifications can request allocation of Attribute Type values within
an Attribute of Data Type TLV. The encapsulating TLV can be
allocated in the same specification, or it can have been previously
allocated.
Specifications need to request allocation within a specific Attribute
Type value (e.g. "TYPE.TLV.*"). Allocations are performed from the
smallest Unassigned value, proceeding to the largest Unassigned
value.
Where the Attribute being allocated is of Data Type TLV, the
Attribute Type tree is extended by one level, as given in the
previous section. Allocations can then be made within that level.
10.3.7. Allocation of Other Data Types
Attribute Type value allocations are otherwise allocated from the
smallest Unassigned value, proceeding to the largest Unassigned
value. e.g. Starting from 241.1, proceeding through 241.255, then to
242.1, through 242.255, etc.
11. Security Considerations
This document defines new formats for data carried inside of RADIUS,
but otherwise makes no changes to the security of the RADIUS
protocol.
Attacks on cryptographic hashes are well known, and are getting
better with time, as discussed in[RFC4270]. RADIUS uses the MD5 hash
[RFC1321] for packet authentication and attribute obfuscation. There
DeKok, Alan Standards Track [Page 52]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
are ongoing efforts in the IETF to analyze and address these issues
for the RADIUS protocol.
As with any protocol change, code changes are required in order to
implement the new features. These code changes have the potential to
introduce new vulnerabilities in the software. Since the RADIUS
server performs network authentication, it is an inviting target for
attackers. We RECOMMEND that access to RADIUS servers be kept to a
minimum.
12. References
12.1. Normative references
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", RFC 2119, March, 1997.
[RFC2865] Rigney, C., Willens, S., Rubens, A. and W. Simpson, "Remote
Authentication Dial In User Service (RADIUS)", RFC 2865, June
2000.
[RFC2866] Rigney, C., "RADIUS Accounting", RFC 2866, June 2000.
[RFC3575] Aboba, B, "IANA Considerations for RADIUS (Remote
Authentication Dial In User Service)", RFC 3575, July 2003.
[RFC5176] Chiba, M, et. al., "Dynamic Authorization Extensions to Remote
Authentication Dial In User Service (RADIUS)", RFC 5176,
January 2008.
[RFC5226] Narten, T. and Alvestrand, H, "Guidelines for Writing an IANA
Considerations Section in RFCs", RFC 5226, May 2008.
[RFC6158] DeKok, A., and Weber, G., "RADIUS Design Guidelines", RFC
6158, March 2011.
[PEN] http://www.iana.org/assignments/enterprise-numbers
12.2. Informative references
[RFC1321] Rivest, R. "The MD5 Message-Digest Algorithm", RFC 1321,
April, 1992
[RFC2868] Zorn, G., et al, " RADIUS Attributes for Tunnel Protocol
Support", RFC 2868, June 2000.
[RFC4270] Hoffman, P, and Schneier, B, "Attacks on Cryptographic Hashes
in Internet Protocols", RFC 4270, November 2005.
DeKok, Alan Standards Track [Page 53]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
[RFC5234] Crocker, D. (Ed.), and Overell, P., "Augmented BNF for Syntax
Specifications: ABNF", RFC 5234, October 2005.
[EDUROAM] Internal Eduroam testing page, data retrieved 04 August 2010.
[ATTR] http://github.com/alandekok/freeradius-
server/tree/master/share/, data retrieved September 2010.
Acknowledgments
This document is the result of long discussions in the IETF RADEXT
working group. The authors would like to thank all of the
participants who contributed various ideas over the years. Their
feedback has been invaluable, and has helped to make this
specification better.
DeKok, Alan Standards Track [Page 54]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
Appendix A - Extended Attribute Generator Program
This section contains "C" program source which can be used for
testing. It reads a line-oriented text file, parses it to create
RADIUS formatted attributes, and prints the hex version of those
attributes to standard output.
The input accepts a grammar similar to that given in Section 8, with
some modifications for usability. For example, blank lines are
allowed, lines beginning with a '#' character are interpreted as
comments, numbers (RADIUS Types, etc.) are checked for minimum /
maximum values, and RADIUS Attribute lengths are enforced.
The program is included here for demonstration purposes only, and
does not define a standard of any kind.
------------------------------------------------------------
/*
* Copyright (c) 2010 IETF Trust and the persons identified as
* authors of the code. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
*
* Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
*
* Neither the name of Internet Society, IETF or IETF Trust, nor the
* names of specific contributors, may be used to endorse or promote
* products derived from this software without specific prior written
* permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
* CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
* INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
* EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
* TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
DeKok, Alan Standards Track [Page 55]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
* OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* Author: Alan DeKok <aland@networkradius.com>
*/
#include <stdlib.h>
#include <stdio.h>
#include <stdint.h>
#include <string.h>
#include <errno.h>
#include <ctype.h>
static int encode_tlv(char *buffer, uint8_t *output, size_t outlen);
static const char *hextab = "0123456789abcdef";
static int encode_data_string(char *buffer,
uint8_t *output, size_t outlen)
{
int length = 0;
char *p;
p = buffer + 1;
while (*p && (outlen > 0)) {
if (*p == '"') {
return length;
}
if (*p != '\\') {
*(output++) = *(p++);
outlen--;
length++;
continue;
}
switch (p[1]) {
default:
*(output++) = p[1];
break;
case 'n':
*(output++) = '\n';
break;
case 'r':
*(output++) = '\r';
DeKok, Alan Standards Track [Page 56]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
break;
case 't':
*(output++) = '\t';
break;
}
outlen--;
length++;
}
fprintf(stderr, "String is not terminated\n");
return 0;
}
static int encode_data_tlv(char *buffer, char **endptr,
uint8_t *output, size_t outlen)
{
int depth = 0;
int length;
char *p;
for (p = buffer; *p != '\0'; p++) {
if (*p == '{') depth++;
if (*p == '}') {
depth--;
if (depth == 0) break;
}
}
if (*p != '}') {
fprintf(stderr, "No trailing '}' in string starting "
"with \"%s\"\n",
buffer);
return 0;
}
*endptr = p + 1;
*p = '\0';
p = buffer + 1;
while (isspace((int) *p)) p++;
length = encode_tlv(p, output, outlen);
if (length == 0) return 0;
return length;
}
DeKok, Alan Standards Track [Page 57]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
static int encode_data(char *p, uint8_t *output, size_t outlen)
{
int length;
if (!isspace((int) *p)) {
fprintf(stderr, "Invalid character following attribute "
"definition\n");
return 0;
}
while (isspace((int) *p)) p++;
if (*p == '{') {
int sublen;
char *q;
length = 0;
do {
while (isspace((int) *p)) p++;
if (!*p) {
if (length == 0) {
fprintf(stderr, "No data\n");
return 0;
}
break;
}
sublen = encode_data_tlv(p, &q, output, outlen);
if (sublen == 0) return 0;
length += sublen;
output += sublen;
outlen -= sublen;
p = q;
} while (*q);
return length;
}
if (*p == '"') {
length = encode_data_string(p, output, outlen);
return length;
}
length = 0;
while (*p) {
DeKok, Alan Standards Track [Page 58]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
char *c1, *c2;
while (isspace((int) *p)) p++;
if (!*p) break;
if(!(c1 = memchr(hextab, tolower((int) p[0]), 16)) ||
!(c2 = memchr(hextab, tolower((int) p[1]), 16))) {
fprintf(stderr, "Invalid data starting at "
"\"%s\"\n", p);
return 0;
}
*output = ((c1 - hextab) << 4) + (c2 - hextab);
output++;
length++;
p += 2;
outlen--;
if (outlen == 0) {
fprintf(stderr, "Too much data\n");
return 0;
}
}
if (length == 0) {
fprintf(stderr, "Empty string\n");
return 0;
}
return length;
}
static int decode_attr(char *buffer, char **endptr)
{
long attr;
attr = strtol(buffer, endptr, 10);
if (*endptr == buffer) {
fprintf(stderr, "No valid number found in string "
"starting with \"%s\"\n", buffer);
return 0;
}
if (!**endptr) {
fprintf(stderr, "Nothing follows attribute number\n");
return 0;
}
DeKok, Alan Standards Track [Page 59]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
if ((attr <= 0) || (attr > 256)) {
fprintf(stderr, "Attribute number is out of valid "
"range\n");
return 0;
}
return (int) attr;
}
static int decode_vendor(char *buffer, char **endptr)
{
long vendor;
if (*buffer != '.') {
fprintf(stderr, "Invalid separator before vendor id\n");
return 0;
}
vendor = strtol(buffer + 1, endptr, 10);
if (*endptr == (buffer + 1)) {
fprintf(stderr, "No valid vendor number found\n");
return 0;
}
if (!**endptr) {
fprintf(stderr, "Nothing follows vendor number\n");
return 0;
}
if ((vendor <= 0) || (vendor > (1 << 24))) {
fprintf(stderr, "Vendor number is out of valid range\n");
return 0;
}
if (**endptr != '.') {
fprintf(stderr, "Invalid data following vendor number\n");
return 0;
}
(*endptr)++;
return (int) vendor;
}
static int encode_tlv(char *buffer, uint8_t *output, size_t outlen)
{
int attr;
int length;
char *p;
DeKok, Alan Standards Track [Page 60]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
attr = decode_attr(buffer, &p);
if (attr == 0) return 0;
output[0] = attr;
output[1] = 2;
if (*p == '.') {
p++;
length = encode_tlv(p, output + 2, outlen - 2);
} else {
length = encode_data(p, output + 2, outlen - 2);
}
if (length == 0) return 0;
if (length > (255 - 2)) {
fprintf(stderr, "TLV data is too long\n");
return 0;
}
output[1] += length;
return length + 2;
}
static int encode_vsa(char *buffer, uint8_t *output, size_t outlen)
{
int vendor;
int attr;
int length;
char *p;
vendor = decode_vendor(buffer, &p);
if (vendor == 0) return 0;
output[0] = 0;
output[1] = (vendor >> 16) & 0xff;
output[2] = (vendor >> 8) & 0xff;
output[3] = vendor & 0xff;
length = encode_tlv(p, output + 4, outlen - 4);
if (length == 0) return 0;
if (length > (255 - 6)) {
fprintf(stderr, "VSA data is too long\n");
return 0;
}
DeKok, Alan Standards Track [Page 61]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
return length + 4;
}
static int encode_evs(char *buffer, uint8_t *output, size_t outlen)
{
int vendor;
int attr;
int length;
char *p;
vendor = decode_vendor(buffer, &p);
if (vendor == 0) return 0;
attr = decode_attr(p, &p);
if (attr == 0) return 0;
output[0] = 0;
output[1] = (vendor >> 16) & 0xff;
output[2] = (vendor >> 8) & 0xff;
output[3] = vendor & 0xff;
output[4] = attr;
length = encode_data(p, output + 5, outlen - 5);
if (length == 0) return 0;
return length + 5;
}
static int encode_extended(char *buffer,
uint8_t *output, size_t outlen)
{
int attr;
int length;
char *p;
attr = decode_attr(buffer, &p);
if (attr == 0) return 0;
output[0] = attr;
if (attr == 26) {
length = encode_evs(p, output + 1, outlen - 1);
} else {
length = encode_data(p, output + 1, outlen - 1);
}
if (length == 0) return 0;
if (length > (255 - 3)) {
fprintf(stderr, "Extended Attr data is too long\n");
DeKok, Alan Standards Track [Page 62]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
return 0;
}
return length + 1;
}
static int encode_extended_flags(char *buffer,
uint8_t *output, size_t outlen)
{
int attr;
int length, total;
char *p;
attr = decode_attr(buffer, &p);
if (attr == 0) return 0;
/* output[0] is the extended attribute */
output[1] = 4;
output[2] = attr;
output[3] = 0;
if (attr == 26) {
length = encode_evs(p, output + 4, outlen - 4);
if (length == 0) return 0;
output[1] += 5;
length -= 5;
} else {
length = encode_data(p, output + 4, outlen - 4);
}
if (length == 0) return 0;
total = 0;
while (1) {
int sublen = 255 - output[1];
if (length <= sublen) {
output[1] += length;
total += output[1];
break;
}
length -= sublen;
memmove(output + 255 + 4, output + 255, length);
memcpy(output + 255, output, 4);
output[1] = 255;
DeKok, Alan Standards Track [Page 63]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
output[3] |= 0x80;
output += 255;
output[1] = 4;
total += 255;
}
return total;
}
static int encode_rfc(char *buffer, uint8_t *output, size_t outlen)
{
int attr;
int length, sublen;
char *p;
attr = decode_attr(buffer, &p);
if (attr == 0) return 0;
length = 2;
output[0] = attr;
output[1] = 2;
if (attr == 26) {
sublen = encode_vsa(p, output + 2, outlen - 2);
} else if ((*p == ' ') || ((attr < 241) || (attr > 246))) {
sublen = encode_data(p, output + 2, outlen - 2);
} else {
if (*p != '.') {
fprintf(stderr, "Invalid data following "
"attribute number\n");
return 0;
}
if (attr < 245) {
sublen = encode_extended(p + 1,
output + 2, outlen - 2);
} else {
/*
* Not like the others!
*/
return encode_extended_flags(p + 1, output, outlen);
}
}
if (sublen == 0) return 0;
DeKok, Alan Standards Track [Page 64]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
if (sublen > (255 -2)) {
fprintf(stderr, "RFC Data is too long\n");
return 0;
}
output[1] += sublen;
return length + sublen;
}
int main(int argc, char *argv[])
{
int lineno;
size_t i, outlen;
FILE *fp;
char input[8192], buffer[8192];
uint8_t output[4096];
if ((argc < 2) || (strcmp(argv[1], "-") == 0)) {
fp = stdin;
} else {
fp = fopen(argv[1], "r");
if (!fp) {
fprintf(stderr, "Error opening %s: %s\n",
argv[1], strerror(errno));
exit(1);
}
}
lineno = 0;
while (fgets(buffer, sizeof(buffer), fp) != NULL) {
char *p = strchr(buffer, '\n');
lineno++;
if (!p) {
if (!feof(fp)) {
fprintf(stderr, "Line %d too long in %s\n",
lineno, argv[1]);
exit(1);
}
} else {
*p = '\0';
}
p = strchr(buffer, '#');
if (p) *p = '\0';
p = buffer;
DeKok, Alan Standards Track [Page 65]
INTERNET-DRAFT RADIUS Extensions 8 January 2013
while (isspace((int) *p)) p++;
if (!*p) continue;
strcpy(input, p);
outlen = encode_rfc(input, output, sizeof(output));
if (outlen == 0) {
fprintf(stderr, "Parse error in line %d of %s\n",
lineno, input);
exit(1);
}
printf("%s -> ", buffer);
for (i = 0; i < outlen; i++) {
printf("%02x ", output[i]);
}
printf("\n");
}
if (fp != stdin) fclose(fp);
return 0;
}
------------------------------------------------------------
Author's Address
Alan DeKok
Network RADIUS SARL
15 av du Granier
38240 Meylan
France
Email: aland@networkradius.com
URI: http://networkradius.com
Avi Lior
Bridgewater Systems Corporation
303 Terry Fox Drive
Suite 100
Ottawa, Ontario K2K 3J1
Canada
Phone: +1 (613) 591-6655
Email: avi@bridgewatersystems.com
URI: http://www.bridgewatersystems.com/
DeKok, Alan Standards Track [Page 66]
Html markup produced by rfcmarkup 1.129d, available from
https://tools.ietf.org/tools/rfcmarkup/