[Docs] [txt|pdf|xml|html] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits] [IPR]

Versions: (draft-brandt-roll-rpl-applicability-home-building) 00 01 02 03 04 05 06 07 08 09 10 11 12 RFC 7733

Roll                                                           A. Brandt
Internet-Draft                                             Sigma Designs
Intended status: Standards Track                             E. Baccelli
Expires: January 22, 2016                                          INRIA
                                                               R. Cragie
                                                                ARM Ltd.
                                                         P. van der Stok
                                                              Consultant
                                                           July 21, 2015


   Applicability Statement: The use of the RPL protocol suite in Home
                    Automation and Building Control
             draft-ietf-roll-applicability-home-building-12

Abstract

   The purpose of this document is to provide guidance in the selection
   and use of protocols from the RPL protocol suite to implement the
   features required for control in building and home environments.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on January 22, 2016.

Copyright Notice

   Copyright (c) 2015 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect



Brandt, et al.          Expires January 22, 2016                [Page 1]


Internet-Draft          RPL in home and building               July 2015


   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
     1.1.  Relationship to other documents . . . . . . . . . . . . .   4
     1.2.  Terminology . . . . . . . . . . . . . . . . . . . . . . .   4
     1.3.  Required Reading  . . . . . . . . . . . . . . . . . . . .   5
     1.4.  Out of scope requirements . . . . . . . . . . . . . . . .   5
   2.  Deployment Scenario . . . . . . . . . . . . . . . . . . . . .   5
     2.1.  Network Topologies  . . . . . . . . . . . . . . . . . . .   6
     2.2.  Traffic Characteristics . . . . . . . . . . . . . . . . .   7
       2.2.1.  General . . . . . . . . . . . . . . . . . . . . . . .   8
       2.2.2.  Source-sink (SS) communication paradigm . . . . . . .   8
       2.2.3.  Publish-subscribe (PS, or pub/sub)) communication
               paradigm  . . . . . . . . . . . . . . . . . . . . . .   9
       2.2.4.  Peer-to-peer (P2P) communication paradigm . . . . . .   9
       2.2.5.  Peer-to-multipeer (P2MP) communication paradigm . . .  10
       2.2.6.  Additional considerations: Duocast and N-cast . . . .  10
       2.2.7.  RPL applicability per communication paradigm  . . . .  10
     2.3.  Layer-2 applicability . . . . . . . . . . . . . . . . . .  11
   3.  Using RPL to meet Functional Requirements . . . . . . . . . .  12
   4.  RPL Profile . . . . . . . . . . . . . . . . . . . . . . . . .  13
     4.1.  RPL Features  . . . . . . . . . . . . . . . . . . . . . .  13
       4.1.1.  RPL Instances . . . . . . . . . . . . . . . . . . . .  13
       4.1.2.  Storing vs. Non-Storing Mode  . . . . . . . . . . . .  14
       4.1.3.  DAO Policy  . . . . . . . . . . . . . . . . . . . . .  14
       4.1.4.  Path Metrics  . . . . . . . . . . . . . . . . . . . .  14
       4.1.5.  Objective Function  . . . . . . . . . . . . . . . . .  14
       4.1.6.  DODAG Repair  . . . . . . . . . . . . . . . . . . . .  14
       4.1.7.  Multicast . . . . . . . . . . . . . . . . . . . . . .  15
       4.1.8.  Security  . . . . . . . . . . . . . . . . . . . . . .  16
       4.1.9.  P2P communications  . . . . . . . . . . . . . . . . .  19
       4.1.10. IPv6 address configuration  . . . . . . . . . . . . .  19
     4.2.  Layer 2 features  . . . . . . . . . . . . . . . . . . . .  19
       4.2.1.  Specifics about layer-2 . . . . . . . . . . . . . . .  19
       4.2.2.  Services provided at layer-2  . . . . . . . . . . . .  19
       4.2.3.  6LowPAN options assumed . . . . . . . . . . . . . . .  20
       4.2.4.  Mesh Link Establishment (MLE) and other things  . . .  20
     4.3.  Recommended Configuration Defaults and Ranges . . . . . .  20
       4.3.1.  Trickle parameters  . . . . . . . . . . . . . . . . .  20
       4.3.2.  Other Parameters  . . . . . . . . . . . . . . . . . .  20
   5.  MPL Profile . . . . . . . . . . . . . . . . . . . . . . . . .  21
     5.1.  Recommended configuration Defaults and Ranges . . . . . .  21
       5.1.1.  Real-Time optimizations . . . . . . . . . . . . . . .  21



Brandt, et al.          Expires January 22, 2016                [Page 2]


Internet-Draft          RPL in home and building               July 2015


       5.1.2.  Trickle parameters  . . . . . . . . . . . . . . . . .  21
       5.1.3.  Other parameters  . . . . . . . . . . . . . . . . . .  22
   6.  Manageability Considerations  . . . . . . . . . . . . . . . .  23
   7.  Security Considerations . . . . . . . . . . . . . . . . . . .  23
     7.1.  Security considerations during initial deployment . . . .  23
     7.2.  Security Considerations during incremental deployment . .  24
     7.3.  Security Considerations for P2P uses  . . . . . . . . . .  25
     7.4.  MPL routing . . . . . . . . . . . . . . . . . . . . . . .  25
     7.5.  RPL Security features . . . . . . . . . . . . . . . . . .  25
   8.  Other related protocols . . . . . . . . . . . . . . . . . . .  25
   9.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  26
   10. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  26
   11. Changelog . . . . . . . . . . . . . . . . . . . . . . . . . .  26
   12. References  . . . . . . . . . . . . . . . . . . . . . . . . .  28
     12.1.  Normative References . . . . . . . . . . . . . . . . . .  28
     12.2.  Informative References . . . . . . . . . . . . . . . . .  32
   Appendix A.  RPL shortcomings in home and building deployments  .  33
     A.1.  Risk of undesired long P2P routes . . . . . . . . . . . .  33
       A.1.1.  Traffic concentration at the root . . . . . . . . . .  34
       A.1.2.  Excessive battery consumption in source nodes . . . .  34
     A.2.  Risk of delayed route repair  . . . . . . . . . . . . . .  34
       A.2.1.  Broken service  . . . . . . . . . . . . . . . . . . .  34
   Appendix B.  Communication failures . . . . . . . . . . . . . . .  35
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  36

1.  Introduction

   The primary purpose of this document is to give guidance in the use
   of the Routing Protocol for Low power and lossy networks (RPL)
   protocol suite in two application domains:

   o  Home automation

   o  Building automation

   The guidance is based on the features required by the requirements
   documents "Home Automation Routing Requirements in Low-Power and
   Lossy Networks" [RFC5826] and "Building Automation Routing
   Requirements in Low-Power and Lossy Networks" [RFC5867] respectively.
   The Advanced Metering Infrastructure is also considered where
   appropriate.  The applicability domains distinguish themselves in the
   way they are operated, their performance requirements, and the most
   likely network structures.  An abstract set of distinct communication
   paradigms is then used to frame the applicability domains.

   Home automation and building automation application domains share a
   substantial number of properties:




Brandt, et al.          Expires January 22, 2016                [Page 3]


Internet-Draft          RPL in home and building               July 2015


   o  In both domains, the network can be disconnected from the ISP and
      must still continue to provide control to the occupants of the
      home/building.  Routing needs to be possible independent of the
      existence of a border router

   o  Both domains are subject to unreliable links but require instant
      and very reliable reactions.  This has impact on routing because
      of timeliness and multipath routing.

   The differences between the two application domains mostly appear in
   commissioning, maintenance and the user interface, which do not
   typically affect routing.  Therefore, the focus of this applicability
   document is on reliability, timeliness, and local routing.

   It should be noted that adherence to the guidance does not
   necessarily guarantee fully interoperable solutions in home
   automation networks and building control networks and that additional
   rigorous and managed programs will be needed to ensure
   interoperability.

1.1.  Relationship to other documents

   The Routing Over Low power and Lossy networks (ROLL) working group
   has specified a set of routing protocols for Low-Power and Lossy
   Networks (LLN) [RFC6550].  This applicability text describes a subset
   of those protocols and the conditions under which the subset is
   appropriate and provides recommendations and requirements for the
   accompanying parameter value ranges.

   In addition, an extension document has been produced specifically to
   provide a solution for reactive discovery of point-to-point routes in
   LLNs [RFC6997].  The present applicability document provides
   recommendations and requirements for the accompanying parameter value
   ranges.

   A common set of security threats are described in [RFC7416].  The
   applicability statements complement the security threats document by
   describing preferred security settings and solutions within the
   applicability statement conditions.  This applicability statement
   recommends lighter weight security solutions appropriate for home and
   building environments and indicates why these solutions are
   appropriate.

1.2.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].



Brandt, et al.          Expires January 22, 2016                [Page 4]


Internet-Draft          RPL in home and building               July 2015


   Additionally, this document uses terminology from [RFC6997],
   [I-D.ietf-roll-trickle-mcast], [RFC7102], [IEEE802.15.4], and
   [RFC6550].

1.3.  Required Reading

   Applicable requirements are described in [RFC5826] and [RFC5867].  A
   survey of the application field is described in [BCsurvey].

1.4.  Out of scope requirements

   The considered network diameter is limited to a maximum diameter of
   10 hops and a typical diameter of 5 hops, which captures the most
   common cases in home automation and building control networks.

   This document does not consider the applicability of Routing Protocol
   for Low-Power and Lossy Networks (RPL)-related specifications for
   urban and industrial applications [RFC5548], [RFC5673], which may
   exhibit significantly larger network diameters.

2.  Deployment Scenario

   The use of communications networks in buildings is essential to
   satisfy energy saving regulations.  Environmental conditions of
   buildings can be adapted to suit the comfort of the individuals
   present inside.  Consequently when no one is present, energy
   consumption can be reduced.  Cost is the main driving factor behind
   deployment of wireless networking in buildings, especially in the
   case of retrofitting, where wireless connectivity saves costs
   incurred due to cabling and building modifications.

   A typical home automation network is comprised of less than 100
   nodes.  Large building deployments may span 10,000 nodes but to
   ensure uninterrupted service of light and air conditioning systems in
   individual zones of the building, nodes are typically organized in
   sub-networks.  Each sub-network in a building automation deployment
   typically contains tens to hundreds of nodes, and for critical
   operations may operate independently from the other sub-networks.

   The main purpose of the home or building automation network is to
   provide control over light and heating/cooling resources.  User
   intervention via wall controllers is combined with movement, light
   and temperature sensors to enable automatic adjustment of window
   blinds, reduction of room temperature, etc.  In general, the sensors
   and actuators in a home or building typically have fixed physical
   locations and will remain in the same home or building automation
   network.




Brandt, et al.          Expires January 22, 2016                [Page 5]


Internet-Draft          RPL in home and building               July 2015


   People expect an immediate and reliable response to their presence or
   actions.  For example, a light not switching on after entry into a
   room may lead to confusion and a profound dissatisfaction with the
   lighting product.

   Monitoring of functional correctness is at least as important as
   timely responses.  Devices typically communicate their status
   regularly and send alarm messages notifying a malfunction of
   controlled equipment or network.

   In building control, the infrastructure of the building management
   network can be shared with the security/access, the Internet Protocol
   (IP) telephony, and the fire/alarm networks.  This approach has a
   positive impact on the operation and cost of the network; however,
   care should be taken to ensure that the availability of the building
   management network does not become compromised beyond the ability for
   critical functions to perform adequately.

   In homes, the entertainment network for audio/video streaming and
   gaming has different requirements, where the most important
   requirement is the need for high bandwidth not typically needed for
   home or building control.  It is therefore expected that the
   entertainment network in the home will mostly be separate from the
   control network, which also lessens the impact on availability of the
   control network

2.1.  Network Topologies

   In general, the home automation network or building control network
   consists of wired and wireless sub-networks.  In large buildings
   especially, the wireless sub-networks can be connected to an IP
   backbone network where all infrastructure services are located, such
   as Domain Name System (DNS), automation servers, etc.

   The wireless sub-network can be configured according to any of the
   following topologies:

   o  A stand-alone network of 10-100 nodes without border router.  This
      typically occurs in the home with a stand-alone control network,
      in low cost buildings, and during installation of high end control
      systems in buildings.

   o  A connected network with one border router.  This configuration
      will happen in homes where home appliances are controlled from
      outside the home, possibly via a smart phone, and in many building
      control scenarios.





Brandt, et al.          Expires January 22, 2016                [Page 6]


Internet-Draft          RPL in home and building               July 2015


   o  A connected network with multiple border routers.  This will
      typically happen in installations of large buildings.

   Many of the nodes are battery-powered and may be sleeping nodes which
   wake up according to clock signals or external events.

   In a building control network, for a large installation with multiple
   border routers, sub-networks often overlap both geographically and
   from a wireless coverage perspective.  Due to two purposes of the
   network, (i) direct control and (ii) monitoring, there may exist two
   types of routing topologies in a given sub-network: (i) a tree-shaped
   collection of routes spanning from a central building controller via
   the border router, on to destination nodes in the sub-network; and/or
   (ii) a flat, un-directed collection of intra-network routes between
   functionally related nodes in the sub-network.

   The majority of nodes in home and building automation networks are
   typically class 0 devices [RFC7228], such as individual wall
   switches.  Only a few nodes (such as multi-purpose remote controls)
   are more expensive Class 1 devices, which can afford more memory
   capacity.

2.2.  Traffic Characteristics

   Traffic may enter the network originating from a central controller
   or it may originate from an intra-network node.  The majority of
   traffic is light-weight point-to-point control style; e.g.  Put-Ack
   or Get-Response.  There are however exceptions.  Bulk data transfer
   is used for firmware update and logging, where firmware updates enter
   the network and logs leave the network.  Group communication is used
   for service discovery or to control groups of nodes, such as light
   fixtures.

   Often, there is a direct physical relation between a controlling
   sensor and the controlled equipment.  For example the temperature
   sensor and room controller are located in the same room sharing the
   same climate conditions.  Consequently, the bulk of senders and
   receivers are separated by a distance that allows one-hop direct path
   communication.  A graph of the communication will show several fully
   connected subsets of nodes.  However, due to interference, multipath
   fading, reflection and other transmission mechanisms, the one-hop
   direct path may be temporally disconnected.  For reliability
   purposes, it is therefore essential that alternative n-hop
   communication routes exist for quick error recovery.  (See Appendix B
   for motivation.)

   Looking over time periods of a day, the networks are very lightly
   loaded.  However, bursts of traffic can be generated by e.g.



Brandt, et al.          Expires January 22, 2016                [Page 7]


Internet-Draft          RPL in home and building               July 2015


   incessant pushing of the button of a remote control, the occurrence
   of a defect, and other unforeseen events.  Under those conditions,
   the timeliness must nevertheless be maintained.  Therefore, measures
   are necessary to remove any unnecessary traffic.  Short routes are
   preferred.  Long multi-hop routes via the border router, should be
   avoided whenever possible.

   Group communication is essential for lighting control.  For example,
   once the presence of a person is detected in a given room, lighting
   control applies to that room only and no other lights should be
   dimmed, or switched on/off.  In many cases, this means that a
   multicast message with a 1-hop and 2-hop radius would suffice to
   control the required lights.  The same argument holds for Heating,
   Ventilating, and Air Conditioning (HVAC) and other climate control
   devices.  To reduce network load, it is advisable that messages to
   the lights in a room are not distributed any further in the mesh than
   necessary based on intended receivers.

   An example of an office surface is shown in [office-light], and the
   current use of wireless lighting control products is shown in
   [occuswitch].

2.2.1.  General

   Whilst air conditioning and other environmental-control applications
   may accept response delays of tens of seconds or longer, alarm and
   light control applications may be regarded as soft real-time systems.
   A slight delay is acceptable, but the perceived quality of service
   degrades significantly if response times exceed 250 ms.  If the light
   does not turn on at short notice, a user may activate the controls
   again, thus causing a sequence of commands such as
   Light{on,off,on,off,..} or Volume{up,up,up,up,up,...}. In addition
   the repetitive sending of commands creates an unnecessary loading of
   the network, which in turn increases the bad responsiveness of the
   network.

2.2.2.  Source-sink (SS) communication paradigm

   This paradigm translates to many sources sending messages to the same
   sink, sometimes reachable via the border router.  As such, source-
   sink (SS) traffic can be present in home and building networks.  The
   traffic may be generated by environmental sensors (often present in a
   wireless sub-network) which push periodic readings to a central
   server.  The readings may be used for pure logging, or more often,
   processed to adjust light, heating and ventilation.  Alarm sensors
   may also generate SS style traffic.  The central server in a home
   automation network will be connected mostly to a wired network
   segment of the home network, although it is likely that cloud



Brandt, et al.          Expires January 22, 2016                [Page 8]


Internet-Draft          RPL in home and building               July 2015


   services will also be used.  The central server in a building
   automation network may be connected to a backbone or be placed
   outside the building.

   With regards to message latency, most SS transmissions can tolerate
   worst-case delays measured in tens of seconds.  Fire detectors,
   however, represent an exception; For example, special provisions with
   respect to the location of the Fire detectors and the smoke dampers
   need to be put in place to meet the stringent delay requirements
   measured in seconds.

2.2.3.  Publish-subscribe (PS, or pub/sub)) communication paradigm

   This paradigm translates to a number of devices expressing their
   interest for a service provided by a server device.  For example, a
   server device can be a sensor delivering temperature readings on the
   basis of delivery criteria, like changes in acquisition value or age
   of the latest acquisition.  In building automation networks, this
   paradigm may be closely related to the SS paradigm given that
   servers, which are connected to the backbone or outside the building,
   can subscribe to data collectors that are present at strategic places
   in the building automation network.  The use of PS will probably
   differ significantly from installation to installation.

2.2.4.  Peer-to-peer (P2P) communication paradigm

   This paradigm translates to a device transferring data to another
   device often connected to the same sub-network.  Peer-to-peer (P2P)
   traffic is a common traffic type in home automation networks.  Most
   building automation networks rely on P2P traffic, described in the
   next paragraph.  Other building automation networks rely on P2P
   control traffic between controls and a local controller box for
   advanced group control.  A local controller box can be further
   connected to service control boxes, thus generating more SS or PS
   traffic.

   P2P traffic is typically generated by remote controls and wall
   controllers which push control messages directly to light or heat
   sources.  P2P traffic has a stringent requirement for low latency
   since P2P traffic often carries application messages that are invoked
   by humans.  As mentioned in Section 2.2.1, application messages
   should be delivered within a few hundred milliseconds - even when
   connections fail momentarily.








Brandt, et al.          Expires January 22, 2016                [Page 9]


Internet-Draft          RPL in home and building               July 2015


2.2.5.  Peer-to-multipeer (P2MP) communication paradigm

   This paradigm translates to a device sending a message as many times
   as there are destination devices.  Peer-to-multipeer (P2MP) traffic
   is common in home and building automation networks.  Often, a
   thermostat in a living room responds to temperature changes by
   sending temperature acquisitions to several fans and valves
   consecutively.  This paradigm is also closely related to the PS
   paradigm in the case where a single server device has multiple
   subscribers.

2.2.6.  Additional considerations: Duocast and N-cast

   This paradigm translates to a device sending a message to many
   destinations in one network transfer invocation.  Multicast is well-
   suited for lighting where a presence sensor sends a presence message
   to a set of lighting devices.  Multicast increases the probability
   that the message is delivered within the strict time constraints.
   The recommended multicast algorithm (e.g.
   [I-D.ietf-roll-trickle-mcast]) provides a mechanism for delivering
   messages to all intended destinations.

2.2.7.  RPL applicability per communication paradigm

   In the case of the SS paradigm applied to a wireless sub-network to a
   server reachable via a border router, the use of RPL [RFC6550] in
   non-storing mode is appropriate.  Given the low resources of the
   devices, source routing will be used from the border router to the
   destination in the wireless sub-network for messages generated
   outside the mesh network.  No specific timing constraints are
   associated with the SS type messages so network repair does not
   violate the operational constraints.  When no SS traffic takes place,
   it is good practice to load only RPL code enabling P2P mode of
   operation [RFC6997] to reduce the code size and satisfy memory
   requirements.

   P2P-RPL [RFC6997] is required for all P2P and P2MP traffic taking
   place between nodes within a wireless sub-network (excluding the
   border router) to assure responsiveness.  Source and destination
   devices are typically physically close based on room layout.
   Consequently, most P2P and P2MP traffic is 1-hop or 2-hop traffic.
   Appendix A explains why P2P-RPL is preferable to RPL for this type of
   communication.  Appendix B explains why reliability measures such as
   multi-path routing are necessary even when 1-hop communication
   dominates.

   Additional advantages of P2P-RPL for home and building automation
   networks are, for example:



Brandt, et al.          Expires January 22, 2016               [Page 10]


Internet-Draft          RPL in home and building               July 2015


   o  Individual wall switches are typically inexpensive class 0 devices
      [RFC7228] with extremely low memory capacities.  Multi-purpose
      remote controls for use in a home environment typically have more
      memory but such devices are asleep when there is no user activity.
      P2P-RPL reactive discovery allows a node to wake up and find new
      routes within a few seconds while memory constrained nodes only
      have to keep routes to relevant targets.

   o  The reactive discovery features of P2P-RPL ensure that commands
      are normally delivered within the 250 ms time window.  When
      connectivity needs to be restored, discovery is typically
      completed within seconds.  In most cases, an alternative (earlier
      discovered) route will work and route rediscovery is not
      necessary.

   o  Broadcast storms typically associated with route discovery for Ad
      hoc On-Demand Distance Vector (AODV) [RFC3561] are less disruptive
      for P2P-RPL.  P2P-RPL has a "STOP" bit which is set by the target
      of a route discovery to notify all other nodes that no more
      Directed Acyclic Graph (DAG) Information Option (DIO) messages
      should be forwarded for this temporary DAG.  Something looking
      like a broadcast storm may happen when no target is responding
      however, in this case, the Trickle suppression mechanism kicks in,
      limiting the number of DIO forwards in dense networks.

   Due to the limited memory of the majority of devices, P2P-RPL SHOULD
   be deployed with source routing in non-storing mode as explained in
   Section 4.1.2.

   Multicast with Multicast Protocol for Low power and Lossy Networks
   (MPL) [I-D.ietf-roll-trickle-mcast] is preferably deployed for N-cast
   over the wireless network.  Configuration constraints that are
   necessary to meet reliability and timeliness with MPL are discussed
   in Section 4.1.7.

2.3.  Layer-2 applicability

   This document applies to [IEEE802.15.4] and [G.9959] which are
   adapted to IPv6 by the adaption layers [RFC4944] and [RFC7428].
   Other layer-2 technologies, accompanied by an "IP over Foo"
   specification, are also relevant provided there is no frame size
   issue, and there are link layer acknowledgements.

   The above mentioned adaptation layers leverage on the compression
   capabilities of [RFC6554] and [RFC6282].  Header compression allows
   small IP packets to fit into a single layer 2 frame even when source
   routing is used.  A network diameter limited to 5 hops helps to
   achieve this even while using source routing.



Brandt, et al.          Expires January 22, 2016               [Page 11]


Internet-Draft          RPL in home and building               July 2015


   Dropped packets are often experienced in the targeted environments.
   Internet Control Message Protocol (ICMP), User Datagram Protocol
   (UDP) and even Transmission Control Protocol (TCP) flows may benefit
   from link layer unicast acknowledgments and retransmissions.  Link
   layer unicast acknowledgments SHOULD be enabled when [IEEE802.15.4]
   or [G.9959] is used with RPL and P2P-RPL.

3.  Using RPL to meet Functional Requirements

   Several features required by [RFC5826], [RFC5867] challenge the P2P
   paths provided by RPL.  Appendix A reviews these challenges.  In some
   cases, a node may need to spontaneously initiate the discovery of a
   path towards a desired destination that is neither the root of a DAG,
   nor a destination originating Destination Advertisement Object (DAO)
   signalling.  Furthermore, P2P paths provided by RPL are not
   satisfactory in all cases because they involve too many intermediate
   nodes before reaching the destination.

   P2P-RPL [RFC6997] SHOULD be used in home automation and building
   control networks, as point-to-point style traffic is substantial and
   route repair needs to be completed within seconds.  P2P-RPL provides
   a reactive mechanism for quick, efficient and root-independent route
   discovery/repair.  The use of P2P-RPL furthermore allows data traffic
   to avoid having to go through a central region around the root of the
   tree, and drastically reduces path length [SOFT11] [INTEROP12].
   These characteristics are desirable in home and building automation
   networks because they substantially decrease unnecessary network
   congestion around the root of the tree.

   When more reliability is required, P2P-RPL enables the establishment
   of multiple independent paths.  For 1-hop destinations this means
   that one 1-hop communication and a second 2-hop communication take
   place via a neighbouring node.  Such a pair of redundant
   communication paths can be achieved by using MPL where the source is
   a MPL forwarder, while a second MPL forwarder is 1 hop away from both
   the source and the destination node.  When the source multicasts the
   message, it may be received by both the destination and the 2nd
   forwarder.  The 2nd forwarder forwards the message to the
   destination, thus providing two routes from sender to destination.

   To provide more reliability with multiple paths, P2P-RPL can maintain
   two independent P2P source routes per destination, at the source.
   Good practice is to use the paths alternately to assess their
   existence.  When one P2P path has failed (possibly only temporarily),
   as described in Appendix B, the alternative P2P path can be used
   without discarding the failed path.  The failed P2P path, unless
   proven to work again, can be safely discarded after a timeout




Brandt, et al.          Expires January 22, 2016               [Page 12]


Internet-Draft          RPL in home and building               July 2015


   (typically 15 minutes).  A new route discovery is done when the
   number of P2P paths is exhausted due to persistent link failures.

4.  RPL Profile

   P2P-RPL SHOULD be used in home automation and building control
   networks.  Its reactive discovery allows for low application response
   times even when on-the-fly route repair is needed.  Non-storing mode
   SHOULD be used to reduce memory consumption in repeaters with
   constrained memory when source routing is used.

4.1.  RPL Features

   An important constraint on the application of RPL is the presence of
   sleeping nodes.

   For example, in a stand-alone network, the master node (or
   coordinator) providing the logical layer-2 identifier and unique node
   identifiers to connected nodes may be a remote control which returns
   to sleep once new nodes have been added.  Due to the absence of the
   border router, there may be no global routable prefixes at all.
   Likewise, there may be no authoritative always-on root node since
   there is no border router to host this function.

   In a network with a border router and many sleeping nodes, there may
   be battery powered sensors and wall controllers configured to contact
   other nodes in response to events and then return to sleep.  Such
   nodes may never detect the announcement of new prefixes via
   multicast.

   In each of the above mentioned constrained deployments, a link layer
   node (e.g. coordinator or master) SHOULD assume the role of
   authoritative root node, transmitting unicast Router Advertisement
   (RA) messages with a Unique Local Address (ULA) prefix information
   option to nodes during the joining process to prepare the nodes for a
   later operational phase, where a border router is added.

   A border router SHOULD be designed to be aware of sleeping nodes in
   order to support the distribution of updated global prefixes to such
   sleeping nodes.

4.1.1.  RPL Instances

   When operating P2P-RPL on a stand-alone basis, there is no
   authoritative root node maintaining a permanent RPL Direction-
   Oriented Directed Acyclic Graph (DODAG).  A node MUST be able to join
   at least one RPL instance, as a new, temporary instance is created




Brandt, et al.          Expires January 22, 2016               [Page 13]


Internet-Draft          RPL in home and building               July 2015


   during each P2P-RPL route discovery operation.  A node MAY be
   designed to join multiple RPL instances.

4.1.2.  Storing vs. Non-Storing Mode

   Non-storing mode MUST be used to cope with the extremely constrained
   memory of a majority of nodes in the network (such as individual
   light switches).

4.1.3.  DAO Policy

   Nodes send DAO messages to establish downward paths from the root to
   themselves.  DAO messages are not acknowledged in networks composed
   of battery operated field devices in order to minimize the power
   consumption overhead associated with path discovery.  The DAO
   messages build up a source route because the nodes MUST be in non-
   storing mode.

   If devices in LLNs participate in multiple RPL instances and DODAGs,
   both the RPLInstance ID and the DODAGID SHOULD be included in the
   DAO.

4.1.4.  Path Metrics

   Expected Transmission Count (ETX) is the RECOMMENDED metric.
   [RFC6551] provides other options.

   Packets from asymmetric and/or unstable links SHOULD be deleted at
   layer 2.

4.1.5.  Objective Function

   Objective Function 0 (OF0) MUST be the Objective Function.  Other
   Objective Functions MAY be used when dictated by circumstances.

4.1.6.  DODAG Repair

   Since P2P-RPL only creates DODAGs on a temporary basis during route
   repair or route discovery, there is no need to repair DODAGs.

   For SS traffic, local repair is sufficient.  The accompanying process
   is known as poisoning and is described in Section 8.2.2.5 of
   [RFC6550].  Given that the majority of nodes in the building do not
   physically move around, creating new DODAGs should not happen
   frequently.






Brandt, et al.          Expires January 22, 2016               [Page 14]


Internet-Draft          RPL in home and building               July 2015


4.1.7.  Multicast

   Commercial lighting deployments may have a need for multicast to
   distribute commands to a group of lights in a timely fashion.
   Several mechanisms exist for achieving such functionality;
   [I-D.ietf-roll-trickle-mcast] is the RECOMMENDED protocol for home
   and building deployments.  This section relies heavily on the
   conclusions of [RT-MPL].

   At reception of a packet, the MPL forwarder starts a series of
   consecutive trickle timer intervals, where the first interval has a
   minimum size of Imin.  Each consecutive interval is twice as long as
   the former with a maximum value of Imax.  There is a maximum number
   of intervals given by max_expiration.  For each interval of length I,
   a time t is randomly chosen in the period [I/2, I].  For a given
   packet, p, MPL counts the number of times it receives p during the
   period [0, t] in a counter c.  At time t, MPL re-broadcasts p when c
   < k, where k is a predefined constant with a value k > 0.

   The density of forwarders and the frequency of message generation are
   important aspects to obtain timeliness during control operations.  A
   high frequency of message generation can be expected when a remote
   control button is incessantly pressed, or when alarm situations
   arise.

   Guaranteeing timeliness is intimately related to the density of the
   MPL routers.  In ideal circumstances the message is propagated as a
   single wave through the network, such that the maximum delay is
   related to the number of hops times the smallest repetition interval
   of MPL.  Each forwarder that receives the message passes the message
   on to the next hop by repeating the message.  When several copies of
   a message reach the forwarder, it is specified that the copy need not
   be repeated.  Repetition of the message can be inhibited by a small
   value of k.  To assure timeliness, the value of k should be chosen
   high enough to make sure that messages are repeated at the first
   arrival of the message in the forwarder.  However, a network that is
   too dense leads to a saturation of the medium that can only be
   prevented by selecting a low value of k.  Consequently, timeliness is
   assured by choosing a relatively high value of k but assuring at the
   same time a low enough density of forwarders to reduce the risk of
   medium saturation.  Depending on the reliability of the network
   links, it is advisable to choose the network such that at least 2
   forwarders per hop repeat messages to the same set of destinations.

   There are no rules about selecting forwarders for MPL.  In buildings
   with central management tools, the forwarders can be selected, but in
   the home is not possible to automatically configure the forwarder
   topology at the time of writing this document.



Brandt, et al.          Expires January 22, 2016               [Page 15]


Internet-Draft          RPL in home and building               July 2015


4.1.8.  Security

   RPL MAY use unsecured RPL messages to reduce message size.  If there
   is a single node that uses unsecured RPL messages, link-layer
   security MUST be used on all nodes.  Therefore all RPL messages MUST
   be secured using either:

   o  RPL message security, or

   o  Link-layer security, or

   o  Both RPL message security and link-layer security

   A symmetric key is used to secure a RPL message using either RPL
   message security or link-layer security.  The symmetric key MUST be
   distributed or established in a secure fashion.  There may be more
   than one symmetric key in use by any node at any one time.  The same
   symmetric key MUST NOT be used for both RPL message security and
   link-layer security between two peer nodes.

4.1.8.1.  Symmetric key distribution

   The scope of symmetric key distribution MUST be no greater than the
   network itself, i.e. a group key.  This document describes what needs
   to be implemented to meet this requirement.  The scope of symmetric
   key distribution MAY be smaller than the network, for example:

   o  A pairwise symmetric key between two peers.

   o  A group key shared between a subset of nodes in the network.

4.1.8.2.  Symmetric key distribution mechanism

   The authentication mechanism as described in Section 6.9 of
   [ZigBeeIP] SHALL be used to securely distribute a network-wide
   symmetric key.

   The purpose of the authentication procedure is to provide mutual
   authentication resulting in:

   o  Preventing untrusted nodes without appropriate credentials from
      joining the trusted network.

   o  Preventing trusted nodes with appropriate credentials from joining
      an untrusted network.

   There is an Authentication Server, which is responsible for
   authenticating the nodes on the network.  If the authentication is



Brandt, et al.          Expires January 22, 2016               [Page 16]


Internet-Draft          RPL in home and building               July 2015


   successful, the Authentication Server sends the network security
   material to the joining node through the PANA protocol ([RFC5191],
   [RFC6345]).  The joining node becomes a full participating node in
   the network and is able to apply layer 2 security to RPL messages
   using the distributed network key.

   The joining node does not initially have access to the network
   security material.  Therefore, it is not able to apply layer 2
   security for the packets exchanged during the authentication process.
   The enforcement point rules at the edge of the network ensure that
   the packets involved in the PANA authentication are processed even
   though they are unsecured at MAC layer.  The rules also ensure that
   any other incoming traffic that is not secured at the MAC layer is
   discarded and is not forwarded.

4.1.8.2.1.  Authentication Stack

   Authentication can be viewed as a protocol stack as a layer
   encapsulates the layers above it.

   o  TLS [RFC5246] MUST be used at the highest layer of the
      authentication stack and carries the authentication exchange.
      There is one cipher suite based on pre-shared key [RFC6655] and
      one cipher suite based on ECC [RFC7251].

   o  EAP-TLS [RFC5216] MUST be used at the next layer to carry the TLS
      records for the authentication protocol.

   o  The Extensible Authentication Protocol [RFC3748] MUST be used to
      provide the mechanisms for mutual authentication.  EAP requires a
      way to transport EAP packets between the joining node and the node
      on which the Authentication Server resides.  These nodes are not
      necessarily in radio range of each other, so it is necessary to
      have multi-hop support in the EAP transport method.  The PANA
      protocol [RFC5191], [RFC6345], which operates over UDP, MUST be
      used for this purpose.  [RFC3748] specifies the derivation of a
      session key using the EAP key hierarchy; only the EAP Master
      Session Key shall be derived, as [RFC5191] specifies that it is
      used to set up keys for PANA authentication and encryption.

   o  PANA [RFC5191] and PANA relay [RFC6345] MUST be used at the next
      layer:

      *  The joining node MUST act as the PANA Client (PaC)

      *  The parent edge router node MUST act as a PANA relay (PRE)
         according to [RFC6345], unless it is also the Authentication




Brandt, et al.          Expires January 22, 2016               [Page 17]


Internet-Draft          RPL in home and building               July 2015


         Server.  All routers at the edge of the network MUST be capable
         of functioning in the PRE role.

      *  The Authentication Server node MUST act as the PANA
         Authentication Agent (PAA).  The Authentication Server MUST be
         able to handle packets relayed according to [RFC6345].

   This network authentication process uses link-local IPv6 addresses
   for transport between the new node and its parent.  If the parent is
   not the Authentication Server, it MUST then relay packets from the
   joining node to the Authentication Server and vice-versa using PANA
   relay mechanism [RFC6345].  The joining node MUST use a link-local
   address based on its EUI-64 as the source address for initial PANA
   authentication message exchanges.

4.1.8.2.2.  Applicability Statements

   The applicability statements describe the relationship between the
   various specifications.

4.1.8.2.2.1.  Applicability Statement for PSK TLS

   [RFC6655] contains AEAD TLS cipher suites that are very similar to
   [RFC5487] whose AEAD part is detailed in [RFC5116].  [RFC5487]
   references both [RFC5288] and the original PSK cipher suite document
   [RFC4279], which references [RFC5246], which defines the TLS 1.2
   messages.

4.1.8.2.2.2.  Applicability Statement for ECC TLS

   [RFC7251] contains AEAD TLS cipher suites that are very similar to
   [RFC5289] whose AEAD part is detailed in [RFC5116].  [RFC5289]
   references the original ECC cipher suite document [RFC4492], which
   references [RFC5246], which defines the TLS 1.2 messages.

4.1.8.2.2.3.  Applicability Statement for EAP-TLS and PANA

   [RFC5216] specifies how [RFC3748] is used to package [RFC5246] TLS
   records into EAP packets.  [RFC5191] provides transportation for the
   EAP packets and the network-wide key carried in an encrypted AVP
   specified in [RFC6786].  The proposed PRF and AUTH hashes based on
   SHA-256 are represented as in [RFC5996] and detailed in [RFC4868].

4.1.8.2.3.  Security using RPL message security

   If RPL is used with secured messages [RFC6550], the following RPL
   security parameter values SHOULD be used:




Brandt, et al.          Expires January 22, 2016               [Page 18]


Internet-Draft          RPL in home and building               July 2015


   o  Counter Time Flag (T) = 0: Do not use timestamp in the Counter
      Field.  Counters based on timestamps are typically more applicable
      to industrial networks where strict timing synchronization between
      nodes is often implemented.  Home and building networks typically
      do not implement such strict timing synchronization therefore a
      monotonically increasing counter is more appropriate.

   o  Algorithm = 0: Use Counter with Cipher Block Chaining Message
      Authentication Code (CBC-MAC Mode) (CCM) with Advanced Encryption
      Standard (AES)-128.  This is the only assigned mode at present.

   o  Key Identifier Mode (KIM) = 10: Use group key, Key Source present,
      Key Index present.  Given the relatively confined perimeter of a
      home or building network, a group key is usually sufficient to
      protect RPL messages sent between nodes.  The use of the Key
      Source field allows multiple group keys to be used within the
      network.

   o  Security Level (LVL) = 0: Use MAC-32.  This is recommended as
      integrity protection for RPL messages is the basic requirement.
      Encryption is unlikely to be necessary given the relatively non-
      confidential nature of RPL message payloads.

4.1.9.  P2P communications

   [RFC6997] MUST be used to accommodate P2P traffic, which is typically
   substantial in home and building automation networks.

4.1.10.  IPv6 address configuration

   Assigned IP addresses MUST be routable and unique within the routing
   domain [RFC5889].

4.2.  Layer 2 features

   No particular requirements exist for layer 2 but for the ones cited
   in the IP over Foo RFCs (see Section 2.3).

4.2.1.  Specifics about layer-2

   Not applicable

4.2.2.  Services provided at layer-2

   Not applicable






Brandt, et al.          Expires January 22, 2016               [Page 19]


Internet-Draft          RPL in home and building               July 2015


4.2.3.  6LowPAN options assumed

   Not applicable

4.2.4.  Mesh Link Establishment (MLE) and other things

   Not applicable

4.3.  Recommended Configuration Defaults and Ranges

   The following sections describe the recommended parameter values for
   P2P-RPL and Trickle.

4.3.1.  Trickle parameters

   Trickle is used to distribute network parameter values to all nodes
   without stringent time restrictions.  The recommended Trickle
   parameter values are:

   o  DIOIntervalMin 4 = 16 ms

   o  DIOIntervalDoublings 14

   o  DIORedundancyConstant 1

   When a node sends a changed DIO, this is an inconsistency and forces
   the receiving node to respond within Imin.  So when something happens
   which affects the DIO, the change is ideally communicated to a node,
   n hops away, within n times Imin.  Often, dependent on the node
   density, packets are lost, or not sent, leading to larger delays.

   In general we can expect DIO changes to propagate within 1 to 3
   seconds within the envisaged networks.

   When nothing happens, the DIO sending interval increases to 4.37
   minutes, thus drastically reducing the network load.  When a node
   does not receive DIO messages during more than 10 minutes it can
   safely conclude the connection with other nodes has been lost.

4.3.2.  Other Parameters

   This section discusses the P2P-RPL parameters.

   P2P-RPL [RFC6997] provides the features requested by [RFC5826] and
   [RFC5867].  P2P-RPL uses a subset of the frame formats and features
   defined for RPL [RFC6550] but may be combined with RPL frame flows in
   advanced deployments.




Brandt, et al.          Expires January 22, 2016               [Page 20]


Internet-Draft          RPL in home and building               July 2015


   The recommended parameter values for P2P-RPL are:

   o  MinHopRankIncrease 1

   o  MaxRankIncrease 0

   o  MaxRank 6

   o  Objective function: OF0

5.  MPL Profile

   MPL is used to distribute values to groups of devices.  Using MPL,
   based on the Trickle algorithm, timeliness should also be guaranteed.
   A deadline of 200 ms needs to be met when human action is followed by
   an immediately observable action such as switching on lights.  The
   deadline needs to be met in a building where the number of hops from
   seed to destination varies between 1 and 10.

5.1.  Recommended configuration Defaults and Ranges

5.1.1.  Real-Time optimizations

   When the network is heavily loaded, MAC delays contribute
   significantly to the end to end delays when MPL intervals between 10
   to 100 ms are used to meet the 200 ms deadline.  It is possible to
   set the number of buffers in the MAC to 1 and set the number of Back-
   off repetitions to 1.  The number of MPL repetitions compensates for
   the reduced probability of transmission per MAC invocation [RT-MPL].

   In addition, end to end delays and message losses are reduced, by
   adding a real-time layer between MPL and MAC to throw away the
   earliest messages (exploiting the MPL message numbering) and favour
   the most recent ones.

5.1.2.  Trickle parameters

   This section proposes values for the Trickle parameters used by MPL
   for the distribution of packets that need to meet a 200 ms deadline.
   The probability of meeting the deadline is increased by (1) choosing
   a small Imin value,(2) reducing the number of MPL intervals thus
   reducing the load, and (3) reducing the number of MPL forwarders to
   also reduce the load.

   The consequence of this approach is that the value of k can be larger
   than 1 because network load reduction is already guaranteed by the
   network configuration.




Brandt, et al.          Expires January 22, 2016               [Page 21]


Internet-Draft          RPL in home and building               July 2015


   Under the condition that the density of MPL repeaters can be limited,
   it is possible to choose low MPL repeat intervals (Imin) connected to
   k values such that k>1.  The minimum value of k is related to:

   o  Value of Imin.  The length of Imin determines the number of
      packets that can be received within the listening period of Imin.

   o  Number of repeaters receiving the broadcast message from the same
      forwarder or seed.  These repeaters repeat within the same Imin
      interval, thus increasing the c counter.

   Within the first MPL interval a limited number, q, of messages can be
   transmitted.  Assuming a 3 ms transmission interval, q is given by q
   = Imin/3.  Assuming that at most q message copies can reach a given
   forwarder within the first repeat interval of length Imin, the
   related MPL parameter values are suggested in the following sections.

5.1.2.1.  Imin

   The recommended value is Imin = 10 to 50 ms.

   When Imin is chosen much smaller, the interference between the copies
   leads to significant losses given that q is much smaller than the
   number of repeated packets.  With much larger intervals the
   probability that the deadline will be met decreases with increasing
   hop count.

5.1.2.2.  Imax

   The recommended value is Imax = 100 to 400 ms.

   The value of Imax is less important than the value of max_expiration.
   Given an Imin value of 10 ms, the 3rd MPL interval has a value of
   10*2*2 = 40 ms.  When Imin has a value of 40 ms, the 3rd interval has
   a value of 160 ms.  Given that more than 3 intervals are unnecessary,
   the Imax does not contribute much to the performance.

5.1.3.  Other parameters

   Other parameters are the k parameter and the max_expiration
   parameter.

   k > q (see condition above).  Under this condition and for small
   Imin, a value of k=2 or k=3 is usually sufficient to minimize the
   losses of packets in the first repeat interval.

   max_expiration = 2 - 4.  Higher values lead to more network load
   while generating copies which will probably not meet their deadline.



Brandt, et al.          Expires January 22, 2016               [Page 22]


Internet-Draft          RPL in home and building               July 2015


6.  Manageability Considerations

   At this moment it is not clear how homenets will be managed.
   Consequently it is not clear which tools will be used and which
   parameters must be exposed for management.

   In building control, management is mandatory.  It is expected that
   installations will be managed using the set of currently available
   tools(including IETF tools like Management Information Base (MIB)
   modules, NETCONF modules, Dynamic Host Configuration Protocol (DHCP)
   and others) with large differences between the ways an installation
   is managed.

7.  Security Considerations

   This section refers to the security considerations of [RFC6997],
   [RFC6550], [I-D.ietf-roll-trickle-mcast], and the counter measures
   discussed in sections 6 and 7 of [RFC7416].

   Communications network security is based on providing integrity
   protection and encryption to messages.  This can be applied at
   various layers in the network protocol stack based on using various
   credentials and a network identity.

   The credentials which are relevant in the case of RPL are: (i) the
   credential used at the link layer in the case where link layer
   security is applied (see Section 7.1) or (ii) the credential used for
   securing RPL messages.  In both cases, the assumption is that the
   credential is a shared key.  Therefore, there MUST be a mechanism in
   place which allows secure distribution of a shared key and
   configuration of network identity.  Both MAY be done using: (i) pre-
   installation using an out-of-band method, (ii) delivered securely
   when a device is introduced into the network or (iii) delivered
   securely by a trusted neighbouring device as described in
   Section 4.1.8.1.  The shared key MUST be stored in a secure fashion
   which makes it difficult to be read by an unauthorized party.

   This document mandates that a layer-2 mechanism be used during
   initial and incremental deployment.  Please see the following
   sections.

7.1.  Security considerations during initial deployment

   Wireless mesh networks are typically secured at the link layer in
   order to prevent unauthorized parties from accessing the information
   exchanged over the links.  It is a basic practice to create a network
   of nodes which share the same keys for link layer security and
   exclude nodes sending unsecured messages.  With per-message data



Brandt, et al.          Expires January 22, 2016               [Page 23]


Internet-Draft          RPL in home and building               July 2015


   origin authentication, it is possible to prevent unauthorized nodes
   joining the mesh.

   At initial deployment the network is secured by consecutively
   securing nodes at the link layer, thus building a network of secured
   nodes.  Section 4.1.8.2 describes a mechanism for building a network
   of secured nodes.

   This document does not specify a multicast security solution.
   Networks deployed with this specification will depend upon layer-2
   security to prevent outsiders from sending multicast traffic.  It is
   recognized that this does not protect this control traffic from
   impersonation by already trusted devices.  This is an area for a
   future specification.

   For building control an installer will use an installation tool that
   establishes a secure communication path with the joining node.  It is
   recognized that the recommendations for initial deployment of
   Section 7 and Section 7.1 do not cover all building requirements such
   as selecting the node-to-secure independent of network topology.

   It is expected that a set of protocol combinations will evolve within
   currently existing alliances of building control manufacturers.  Each
   set satisfies the installation requirements of installers, operators,
   and manufacturers of building control networks in a given
   installation context, e.g lighting deployment in offices, HVAC
   installation, incremental addition of equipment in homes, and others.

   In the home, nodes can be visually inspected by the home owner and a
   simple procedure, e.g. pushing buttons simultaneously on an already
   secured device and an unsecured joining device is usually sufficient
   to ensure that the unsecured joining device is authenticated and
   configured securely, and paired appropriately.

   This recommendation is in line with the countermeasures described in
   section 6.1.1 of [RFC7416].

7.2.  Security Considerations during incremental deployment

   Once a network is operational, new nodes need to be added, or nodes
   fail and need to be replaced.  When a new node needs to be added to
   the network, the new node is joined to the network via an assisting
   node in the manner described in Section 7.1.

   On detection of a compromised node, all trusted nodes need to have
   their symmetric keys known to be shared with the compromised node re-
   keyed, and the trusted network is built up as described in
   Section 7.1.



Brandt, et al.          Expires January 22, 2016               [Page 24]


Internet-Draft          RPL in home and building               July 2015


7.3.  Security Considerations for P2P uses

   Refer to the security considerations of [RFC6997].

7.4.  MPL routing

   The routing of MPL is determined by the enabling of the interfaces
   for specified Multicast addresses.  The specification of these
   addresses can be done via a Constrained Application Protocol (CoAP)
   application as specified in [RFC7390].  An alternative is the
   creation of a MPL MIB and use of Simple Network Management Protocol
   (SNMP)v3 [RFC3411] or equivalent techniques to specify the Multicast
   addresses in the MIB.  For secure dissemination of MPL packets, layer
   2 security SHOULD be used and the configuration of multicast
   addresses as described in this section MUST be secure.

7.5.  RPL Security features

   This section follows the structure of section 8, "RPL security
   features" of [RFC7416].  [RFC7416] provides a thorough analysis of
   security threats and proposed counter measures relevant to RPL and
   MPL.

   In accordance with section 8.1 of [RFC7416], "Confidentiality
   features", RPL message security implements payload protection, as
   explained in Section 7 of this document.  The attributes key-length
   and life-time of the keys depend on operational conditions,
   maintenance and installation procedures.

   Section 7.1 and Section 7.2 of this document recommend link-layer
   security to assure integrity in accordance with section 8.2 of
   [RFC7416], "Integrity features".

   The provision of multiple paths recommended in section 8.3
   "Availability features" of [RFC7416] is also recommended from a
   reliability point of view.  Randomly choosing paths MAY be supported.

   A mechanism for key management, discussed in section 8.4, "Key
   Management" of [RFC7416], is provided in Section 4.1.8.2.

   Section 7.5, "Considerations on Matching Application Domain Needs" of
   [RFC7416] applies as such.

8.  Other related protocols

   Application and transport protocols used in home and building
   automation domains are expected to mostly consist in CoAP over UDP,
   or equivalents.  Typically, UDP is used for IP transport to keep down



Brandt, et al.          Expires January 22, 2016               [Page 25]


Internet-Draft          RPL in home and building               July 2015


   the application response time and bandwidth overhead.  CoAP is used
   at the application layer to reduce memory footprint and bandwidth
   requirements.

9.  IANA Considerations

   No considerations for IANA pertain to this document.

10.  Acknowledgements

   This document reflects discussions and remarks from several
   individuals including (in alphabetical order): Stephen Farrell, Mukul
   Goyal, Sandeep Kumar, Jerry Martocci, Catherine Meadows, Yoshihira
   Ohba, Charles Perkins, Yvonne-Anne Pignolet, Michael Richardson, Ines
   Robles, Zach Shelby, and Meral Sherazipour.

11.  Changelog

   RFC editor, please delete this section before publication.

   Changes from version 0 to version 1.

   o  Adapted section structure to template.

   o  Standardized the reference syntax.

   o  Section 2.2, moved everything concerning algorithms to section
      2.2.7, and adapted text in 2.2.1-2.2.6.

   o  Added MPL parameter text to section 4.1.7 and section 4.3.1.

   o  Replaced all TODO sections with text.

   o  Consistent use of border router, monitoring, home- and building
      network.

   o  Reformulated security aspects with references to other
      publications.

   o  MPL and RPL parameter values introduced.

   Changes from version 1 to version 2.

   o  Clarified common characteristics of control in home and building.

   o  Clarified failure behaviour of point to point communication in
      appendix.




Brandt, et al.          Expires January 22, 2016               [Page 26]


Internet-Draft          RPL in home and building               July 2015


   o  Changed examples, more hvac and less lighting.

   o  Clarified network topologies.

   o  replaced reference to smart_object paper by reference to I-D.roll-
      security-threats

   o  Added a concise definition of secure delivery and secure storage

   o  Text about securing network with PANA

   Changes from version 2 to version 3.

   o  Changed security section to follow the structure of security
      threats draft.

   o  Added text to DODAG repair sub-section

   Changes from version 3 to version 4.

   o  Renumbered sections and moved text to conform to applicability
      template

   o  Extended MPL parameter value text

   o  Added references to building control products

   Changes from version 4 to version 5.

   o  Large editing effort to streamline text

   o  Rearranged Normative and Informative references

   o  Replaced RFC2119 terminology by non-normative terminology

   o  Rearranged text of section 7, 7.1, and 7.2 to agree with the
      intention of section 7.2

   Changes from version 5 to version 6.

   o  Issues #162 - #166 addressed

   Changes from version 6 to version 7.

   o  Text of section 7.1 edited for better security coverage.

   Changes from version 7 to version 8.




Brandt, et al.          Expires January 22, 2016               [Page 27]


Internet-Draft          RPL in home and building               July 2015


   o  Requirements language paragraph removed

   o  Acronyms clarified

   o  MPL parameters clarified

   Changes from version 8 to version 9.

   o  More acronyms clarified

   o  References updated

   Changes from version 9 to version 10.

   o  Changes due to IESG and security review

   o  Requirements language reinstated

   o  RPL security parameter selection clarified

   o  Removed multicast security reference

   Changes from version 10 to 11.

   o  Further changes due to IESG and security review

   o  ZigBee IP authentication and key establishment specified

   Changes from version 11 to 12.

   o  Further clarifications added

12.  References

12.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3748]  Aboba, B., Blunk, L., Vollbrecht, J., Carlson, J., and H.
              Levkowetz, Ed., "Extensible Authentication Protocol
              (EAP)", RFC 3748, DOI 10.17487/RFC3748, June 2004,
              <http://www.rfc-editor.org/info/rfc3748>.

   [RFC4279]  Eronen, P., Ed. and H. Tschofenig, Ed., "Pre-Shared Key
              Ciphersuites for Transport Layer Security (TLS)",
              RFC 4279, DOI 10.17487/RFC4279, December 2005,
              <http://www.rfc-editor.org/info/rfc4279>.



Brandt, et al.          Expires January 22, 2016               [Page 28]


Internet-Draft          RPL in home and building               July 2015


   [RFC4492]  Blake-Wilson, S., Bolyard, N., Gupta, V., Hawk, C., and B.
              Moeller, "Elliptic Curve Cryptography (ECC) Cipher Suites
              for Transport Layer Security (TLS)", RFC 4492,
              DOI 10.17487/RFC4492, May 2006,
              <http://www.rfc-editor.org/info/rfc4492>.

   [RFC4868]  Kelly, S. and S. Frankel, "Using HMAC-SHA-256, HMAC-SHA-
              384, and HMAC-SHA-512 with IPsec", RFC 4868,
              DOI 10.17487/RFC4868, May 2007,
              <http://www.rfc-editor.org/info/rfc4868>.

   [RFC4944]  Montenegro, G., Kushalnagar, N., Hui, J., and D. Culler,
              "Transmission of IPv6 Packets over IEEE 802.15.4
              Networks", RFC 4944, DOI 10.17487/RFC4944, September 2007,
              <http://www.rfc-editor.org/info/rfc4944>.

   [RFC5116]  McGrew, D., "An Interface and Algorithms for Authenticated
              Encryption", RFC 5116, DOI 10.17487/RFC5116, January 2008,
              <http://www.rfc-editor.org/info/rfc5116>.

   [RFC5191]  Forsberg, D., Ohba, Y., Ed., Patil, B., Tschofenig, H.,
              and A. Yegin, "Protocol for Carrying Authentication for
              Network Access (PANA)", RFC 5191, DOI 10.17487/RFC5191,
              May 2008, <http://www.rfc-editor.org/info/rfc5191>.

   [RFC5216]  Simon, D., Aboba, B., and R. Hurst, "The EAP-TLS
              Authentication Protocol", RFC 5216, DOI 10.17487/RFC5216,
              March 2008, <http://www.rfc-editor.org/info/rfc5216>.

   [RFC5246]  Dierks, T. and E. Rescorla, "The Transport Layer Security
              (TLS) Protocol Version 1.2", RFC 5246,
              DOI 10.17487/RFC5246, August 2008,
              <http://www.rfc-editor.org/info/rfc5246>.

   [RFC5288]  Salowey, J., Choudhury, A., and D. McGrew, "AES Galois
              Counter Mode (GCM) Cipher Suites for TLS", RFC 5288,
              DOI 10.17487/RFC5288, August 2008,
              <http://www.rfc-editor.org/info/rfc5288>.

   [RFC5289]  Rescorla, E., "TLS Elliptic Curve Cipher Suites with SHA-
              256/384 and AES Galois Counter Mode (GCM)", RFC 5289,
              DOI 10.17487/RFC5289, August 2008,
              <http://www.rfc-editor.org/info/rfc5289>.

   [RFC5487]  Badra, M., "Pre-Shared Key Cipher Suites for TLS with SHA-
              256/384 and AES Galois Counter Mode", RFC 5487,
              DOI 10.17487/RFC5487, March 2009,
              <http://www.rfc-editor.org/info/rfc5487>.



Brandt, et al.          Expires January 22, 2016               [Page 29]


Internet-Draft          RPL in home and building               July 2015


   [RFC5548]  Dohler, M., Ed., Watteyne, T., Ed., Winter, T., Ed., and
              D. Barthel, Ed., "Routing Requirements for Urban Low-Power
              and Lossy Networks", RFC 5548, DOI 10.17487/RFC5548, May
              2009, <http://www.rfc-editor.org/info/rfc5548>.

   [RFC5673]  Pister, K., Ed., Thubert, P., Ed., Dwars, S., and T.
              Phinney, "Industrial Routing Requirements in Low-Power and
              Lossy Networks", RFC 5673, DOI 10.17487/RFC5673, October
              2009, <http://www.rfc-editor.org/info/rfc5673>.

   [RFC5826]  Brandt, A., Buron, J., and G. Porcu, "Home Automation
              Routing Requirements in Low-Power and Lossy Networks",
              RFC 5826, DOI 10.17487/RFC5826, April 2010,
              <http://www.rfc-editor.org/info/rfc5826>.

   [RFC5867]  Martocci, J., Ed., De Mil, P., Riou, N., and W. Vermeylen,
              "Building Automation Routing Requirements in Low-Power and
              Lossy Networks", RFC 5867, DOI 10.17487/RFC5867, June
              2010, <http://www.rfc-editor.org/info/rfc5867>.

   [RFC5996]  Kaufman, C., Hoffman, P., Nir, Y., and P. Eronen,
              "Internet Key Exchange Protocol Version 2 (IKEv2)",
              RFC 5996, DOI 10.17487/RFC5996, September 2010,
              <http://www.rfc-editor.org/info/rfc5996>.

   [RFC6282]  Hui, J., Ed. and P. Thubert, "Compression Format for IPv6
              Datagrams over IEEE 802.15.4-Based Networks", RFC 6282,
              DOI 10.17487/RFC6282, September 2011,
              <http://www.rfc-editor.org/info/rfc6282>.

   [RFC6345]  Duffy, P., Chakrabarti, S., Cragie, R., Ohba, Y., Ed., and
              A. Yegin, "Protocol for Carrying Authentication for
              Network Access (PANA) Relay Element", RFC 6345,
              DOI 10.17487/RFC6345, August 2011,
              <http://www.rfc-editor.org/info/rfc6345>.

   [RFC6550]  Winter, T., Ed., Thubert, P., Ed., Brandt, A., Hui, J.,
              Kelsey, R., Levis, P., Pister, K., Struik, R., Vasseur,
              JP., and R. Alexander, "RPL: IPv6 Routing Protocol for
              Low-Power and Lossy Networks", RFC 6550,
              DOI 10.17487/RFC6550, March 2012,
              <http://www.rfc-editor.org/info/rfc6550>.

   [RFC6551]  Vasseur, JP., Ed., Kim, M., Ed., Pister, K., Dejean, N.,
              and D. Barthel, "Routing Metrics Used for Path Calculation
              in Low-Power and Lossy Networks", RFC 6551,
              DOI 10.17487/RFC6551, March 2012,
              <http://www.rfc-editor.org/info/rfc6551>.



Brandt, et al.          Expires January 22, 2016               [Page 30]


Internet-Draft          RPL in home and building               July 2015


   [RFC6554]  Hui, J., Vasseur, JP., Culler, D., and V. Manral, "An IPv6
              Routing Header for Source Routes with the Routing Protocol
              for Low-Power and Lossy Networks (RPL)", RFC 6554,
              DOI 10.17487/RFC6554, March 2012,
              <http://www.rfc-editor.org/info/rfc6554>.

   [RFC6655]  McGrew, D. and D. Bailey, "AES-CCM Cipher Suites for
              Transport Layer Security (TLS)", RFC 6655,
              DOI 10.17487/RFC6655, July 2012,
              <http://www.rfc-editor.org/info/rfc6655>.

   [RFC6786]  Yegin, A. and R. Cragie, "Encrypting the Protocol for
              Carrying Authentication for Network Access (PANA)
              Attribute-Value Pairs", RFC 6786, DOI 10.17487/RFC6786,
              November 2012, <http://www.rfc-editor.org/info/rfc6786>.

   [RFC6997]  Goyal, M., Ed., Baccelli, E., Philipp, M., Brandt, A., and
              J. Martocci, "Reactive Discovery of Point-to-Point Routes
              in Low-Power and Lossy Networks", RFC 6997,
              DOI 10.17487/RFC6997, August 2013,
              <http://www.rfc-editor.org/info/rfc6997>.

   [RFC6998]  Goyal, M., Ed., Baccelli, E., Brandt, A., and J. Martocci,
              "A Mechanism to Measure the Routing Metrics along a Point-
              to-Point Route in a Low-Power and Lossy Network",
              RFC 6998, DOI 10.17487/RFC6998, August 2013,
              <http://www.rfc-editor.org/info/rfc6998>.

   [RFC7102]  Vasseur, JP., "Terms Used in Routing for Low-Power and
              Lossy Networks", RFC 7102, DOI 10.17487/RFC7102, January
              2014, <http://www.rfc-editor.org/info/rfc7102>.

   [RFC7251]  McGrew, D., Bailey, D., Campagna, M., and R. Dugal, "AES-
              CCM Elliptic Curve Cryptography (ECC) Cipher Suites for
              TLS", RFC 7251, DOI 10.17487/RFC7251, June 2014,
              <http://www.rfc-editor.org/info/rfc7251>.

   [RFC7416]  Tsao, T., Alexander, R., Dohler, M., Daza, V., Lozano, A.,
              and M. Richardson, Ed., "A Security Threat Analysis for
              the Routing Protocol for Low-Power and Lossy Networks
              (RPLs)", RFC 7416, DOI 10.17487/RFC7416, January 2015,
              <http://www.rfc-editor.org/info/rfc7416>.

   [I-D.ietf-roll-trickle-mcast]
              Hui, J. and R. Kelsey, "Multicast Protocol for Low power
              and Lossy Networks (MPL)", draft-ietf-roll-trickle-
              mcast-12 (work in progress), June 2015.




Brandt, et al.          Expires January 22, 2016               [Page 31]


Internet-Draft          RPL in home and building               July 2015


   [IEEE802.15.4]
              "IEEE 802.15.4 - Standard for Local and metropolitan area
              networks -- Part 15.4: Low-Rate Wireless Personal Area
              Networks", <IEEE Standard 802.15.4>.

   [G.9959]   "ITU-T G.9959 Short range narrow-band digital
              radiocommunication transceivers - PHY and MAC layer
              specifications", <ITU-T G.9959>.

12.2.  Informative References

   [RFC3411]  Harrington, D., Presuhn, R., and B. Wijnen, "An
              Architecture for Describing Simple Network Management
              Protocol (SNMP) Management Frameworks", STD 62, RFC 3411,
              DOI 10.17487/RFC3411, December 2002,
              <http://www.rfc-editor.org/info/rfc3411>.

   [RFC3561]  Perkins, C., Belding-Royer, E., and S. Das, "Ad hoc On-
              Demand Distance Vector (AODV) Routing", RFC 3561,
              DOI 10.17487/RFC3561, July 2003,
              <http://www.rfc-editor.org/info/rfc3561>.

   [RFC5889]  Baccelli, E., Ed. and M. Townsley, Ed., "IP Addressing
              Model in Ad Hoc Networks", RFC 5889, DOI 10.17487/RFC5889,
              September 2010, <http://www.rfc-editor.org/info/rfc5889>.

   [RFC7228]  Bormann, C., Ersue, M., and A. Keranen, "Terminology for
              Constrained-Node Networks", RFC 7228,
              DOI 10.17487/RFC7228, May 2014,
              <http://www.rfc-editor.org/info/rfc7228>.

   [RFC7390]  Rahman, A., Ed. and E. Dijk, Ed., "Group Communication for
              the Constrained Application Protocol (CoAP)", RFC 7390,
              DOI 10.17487/RFC7390, October 2014,
              <http://www.rfc-editor.org/info/rfc7390>.

   [RFC7428]  Brandt, A. and J. Buron, "Transmission of IPv6 Packets
              over ITU-T G.9959 Networks", RFC 7428,
              DOI 10.17487/RFC7428, February 2015,
              <http://www.rfc-editor.org/info/rfc7428>.

   [SOFT11]   Baccelli, E., Phillip, M., and M. Goyal, "The P2P-RPL
              Routing Protocol for IPv6 Sensor Networks: Testbed
              Experiments",  Proceedings of the Conference on Software
              Telecommunications and Computer Networks, Split, Croatia,,
              September 2011.





Brandt, et al.          Expires January 22, 2016               [Page 32]


Internet-Draft          RPL in home and building               July 2015


   [INTEROP12]
              Baccelli, E., Phillip, M., Brandt, A., Valev , H., and J.
              Buron , "Report on P2P-RPL Interoperability Testing",
              RR-7864 INRIA Research Report RR-7864, January 2012.

   [RT-MPL]   van der Stok, P., "Real-Time multicast for wireless mesh
              networks using MPL", White paper,
               http://www.vanderstok.org/papers/Real-time-MPL.pdf, April
              2014.

   [occuswitch]
              Lighting, Philips., "OccuSwitch wireless", Brochure,  http
              ://www.philipslightingcontrols.com/assets/cms/uploads/file
              s/osw/MK_OSWNETBROC_5.pdf, May 2012.

   [office-light]
              Clanton and Associates, ., "A Life Cycle Cost Evaluation
              of Multiple Lighting Control Strategies", Wireless
              Lighting Control,  http://www.daintree.net/wp-
              content/uploads/2014/02/
              clanton_lighting_control_report_0411.pdf, February 2014.

   [RTN2011]  Holtman, K. and P. van der Stok, "Real-time routing for
              low-latency 802.15.4 control networks", International
              Workshop on Real-Time Networks; Euromicro Conference on
              Real-Time Systems, July 2011.

   [MEAS]     Holtman, K., "Connectivity loss in large scale IEEE
              802.15.4 network",  Private Communication, November 2013.

   [BCsurvey]
              Kastner, W., Neugschwandtner, G., Soucek, S., and H.
              Newman, "Communication Systems for Building Automation and
              Control", Proceedings of the IEEE  Vol 93, No 6, June
              2005.

   [ZigBeeIP]
              ZigBee Alliance, ., "ZigBee IP specification", ZigBee
              document 095023r34, March 2014.

Appendix A.  RPL shortcomings in home and building deployments

A.1.  Risk of undesired long P2P routes

   The DAG, being a tree structure is formed from a root.  If nodes
   residing in different branches have a need for communicating
   internally, DAG mechanisms provided in RPL [RFC6550] will propagate
   traffic towards the root, potentially all the way to the root, and



Brandt, et al.          Expires January 22, 2016               [Page 33]


Internet-Draft          RPL in home and building               July 2015


   down along another branch [RFC6998].  In a typical example two nodes
   could reach each other via just two router nodes but in unfortunate
   cases, RPL may send traffic three hops up and three hops down again.
   This leads to several undesired phenomena described in the following
   sections.

A.1.1.  Traffic concentration at the root

   If many P2P data flows have to move up towards the root to get down
   again in another branch there is an increased risk of congestion the
   nearer to the root of the DAG the data flows.  Due to the broadcast
   nature of RF systems any child node of the root is not just directing
   RF power downwards its sub-tree but just as much upwards towards the
   root; potentially jamming other MP2P traffic leaving the tree or
   preventing the root of the DAG from sending P2MP traffic into the DAG
   because the listen-before-talk link-layer protection kicks in.

A.1.2.  Excessive battery consumption in source nodes

   Battery-powered nodes originating P2P traffic depend on the route
   length.  Long routes cause source nodes to stay awake for longer
   periods before returning to sleep.  Thus, a longer route translates
   proportionally (more or less) into higher battery consumption.

A.2.  Risk of delayed route repair

   The RPL DAG mechanism uses DIO and DAO messages to monitor the health
   of the DAG.  In rare occasions, changed radio conditions may render
   routes unusable just after a destination node has returned a DAO
   indicating that the destination is reachable.  Given enough time, the
   next Trickle timer-controlled DIO/DAO update will eventually repair
   the broken routes, however this may not occur in a timely manner
   appropriate to the application.  In an apparently stable DAG,
   Trickle-timer dynamics may reduce the update rate to a few times
   every hour.  If a user issues an actuator command, e.g. light on in
   the time interval between the last DAO message was issued the
   destination module and the time one of the parents sends the next
   DIO, the destination cannot be reached.  There is no mechanism in RPL
   to initiate restoration of connectivity in a reactive fashion.  The
   consequence is a broken service in home and building applications.

A.2.1.  Broken service

   Experience from the telecom industry shows that if the voice delay
   exceeds 250ms, users start getting confused, frustrated and/or
   annoyed.  In the same way, if the light does not turn on within the
   same period of time, a home control user will activate the controls
   again, causing a sequence of commands such as



Brandt, et al.          Expires January 22, 2016               [Page 34]


Internet-Draft          RPL in home and building               July 2015


   Light{on,off,off,on,off,..} or Volume{up,up,up,up,up,...}. Whether
   the outcome is nothing or some unintended response this is
   unacceptable.  A controlling system must be able to restore
   connectivity to recover from the error situation.  Waiting for an
   unknown period of time is not an option.  While this issue was
   identified during the P2P analysis, it applies just as well to
   application scenarios where an IP application outside the LLN
   controls actuators, lights, etc.

Appendix B.  Communication failures

   Measurements on the connectivity between neighbouring nodes are
   discussed in [RTN2011] and [MEAS].

   The work is motivated by the measurements in literature which affirm
   that the range of an antenna is not circle symmetric but that the
   signal strength of a given level follows an intricate pattern around
   the antenna, and there may be holes within the area delineated by an
   iso-strength line.  It is reported that communication is not
   symmetric: reception of messages from node A by node B does not imply
   reception of messages from node B by node A.  The quality of the
   signal fluctuates over time, and also the height of the antenna
   within a room can have consequences for the range.  As function of
   the distance from the source, three regions are generally recognized:
   (1) a clear region with excellent signal quality, (2) a region with
   fluctuating signal quality, (3) a region without reception.  In the
   text below it is shown that installation of meshes with neighbours in
   the clear region is not sufficient.

   [RTN2011] extends existing work by:

   o  Observations over periods of at least a week,

   o  Testing links that are in the clear region,

   o  Observation in an office building during working hours,

   o  Concentrating on one-hop and two-hop routes.

   Eight nodes were distributed over a surface of 30m2.  All nodes are
   at one hop distance from each other and are situated in the clear
   region of each other.  Each node sends messages to each of its
   neighbours, and repeats the message until it arrives.  The latency of
   the message was measured over periods of at least a week.  It is
   noticed that latencies longer than a second occurred without apparent
   reasons, but only during working days and never in the weekends.  Bad
   periods could last for minutes.  By sending messages via two paths:
   (1) one hop path directly, and (2) two hop path via a randomly chosen



Brandt, et al.          Expires January 22, 2016               [Page 35]


Internet-Draft          RPL in home and building               July 2015


   neighbour, the probability of delays larger than 100 ms decreased
   significantly.

   The conclusion is that even for 1-hop communication between not too
   distant "Line of Sight" nodes, there are periods of low reception in
   which communication deadlines of 200 ms are exceeded.  It pays to
   send a second message over a 2-hop path to increase the reliability
   of timely message transfer.

   [MEAS] confirms that temporary bad reception by close neighbours can
   occur within other types of areas.  Nodes were installed on the
   ceiling in a grid with a distance of 30-50 cm between nodes. 200
   nodes were distributed over an area of 10m x 5m.  It clearly
   transpired that with increasing distance the probability of reception
   decreases.  At the same time a few nodes furthest away from the
   sender had a high probability of message reception, while some close
   neighbours of the sender did not receive messages.  The patterns of
   clear reception nodes evolved over time.

   The conclusion is that even for direct neighbours reception can
   temporarily be bad during periods of several minutes.  For a reliable
   and timely communication it is imperative to have at least two
   communication paths available (e.g. two hop paths next to the 1-hop
   path for direct neighbours).

Authors' Addresses

   Anders Brandt
   Sigma Designs

   Email: anders_Brandt@sigmadesigns.com


   Emmanuel Baccelli
   INRIA

   Email: Emmanuel.Baccelli@inria.fr


   Robert Cragie
   ARM Ltd.
   110 Fulbourn Road
   Cambridge  CB1 9NJ
   UK

   Email: robert.cragie@gridmerge.com





Brandt, et al.          Expires January 22, 2016               [Page 36]


Internet-Draft          RPL in home and building               July 2015


   Peter van der Stok
   Consultant

   Email: consultancy@vanderstok.org















































Brandt, et al.          Expires January 22, 2016               [Page 37]


Html markup produced by rfcmarkup 1.121, available from https://tools.ietf.org/tools/rfcmarkup/