[Docs] [txt|pdf] [Tracker] [WG] [Email] [Nits]

Versions: 00 RFC 1270

Network Working Group                                           April 1991
Internet-Draft                                          SNMP Working Group







                             IETF SNMP Working Group
                                  Internet Draft
                           SNMP Communications Services

                                    April 1991


                               Frank J. Kastenholz






          1.  Status of This Memo

          This Internet Draft document will be submitted to the RFC
          editor for publication as an Informational RFC.  The following
          is proposed as the status paragraph of the published RFC:

              This RFC is being distributed to members of the Inter-
              net  community as an Informational RFC.  The intent is
              to present a discussion on the issues relating to  the
              communications  services  for  SNMP.  While the issues
              discussed may not be directly relevant to the research
              problems of the Internet, they may be interesting to a
              number of researchers and implementors.


          Distribution of this memo is unlimited.
























          Internet Draft   SNMP Communications Services       April 1991


          2.  Introduction

          This document discusses various issues to be considered when
          determining the underlying communications services to be used
          by an SNMP implementation.

          As reported in RFC 1052, IAB Recommendations for the
          Development of Internet Network Management Standards [8], a
          two-prong strategy for network management of TCP/IP-based
          internets was undertaken.  In the short-term, the Simple
          Network Management Protocol (SNMP), defined in RFC 1067, was
          to be used to manage nodes in the Internet community.  In the
          long-term, the use of the OSI network management framework was
          to be examined.  Two documents were produced to define the
          management information: RFC 1065, which defined the Structure
          of Management Information (SMI), and RFC 1066, which defined
          the Management Information Base (MIB).  Both of these
          documents were designed so as to be compatible with both the
          SNMP and the OSI network management framework.

          This strategy was quite successful in the short-term:
          Internet-based network management technology was fielded, by
          both the research and commercial communities, within a few
          months.  As a result of this, portions of the Internet
          community became network manageable in a timely fashion.

          In May of 1990, the core documents were elevated to "Standard
          Protocols" with "Recommended" status.  As such, the Internet-
          standard network management framework consists of: Structure
          and Identification of Management Information for TCP/IP-based
          internets, RFC 1155 [9], which describes how managed objects
          contained in the MIB are defined; Management Information Base
          for Network Management of TCP/IP-based internets, which
          describes the managed objects contained in the MIB, RFC 1156
          [10]; and, the Simple Network Management Protocol, RFC 1157
          [1], which defines the protocol used to manage these objects.

          In parallel with this activity, documents specifying how to
          transport SNMP messages over protocols other than UDP/IP have
          been developed and published: SNMP Over Ethernet [3], SNMP
          Over OSI [2], and SNMP Over IPX [6] and it would be suprising
          if more were not developed.  These memos have caused a degree
          of confusion in the community.  This document is intended to
          disperse that confusion by discussing the issues of relevance
          to an implementor when choosing how to encapsulate SNMP





          Frank Kastenholz                                      [Page 1]


          Internet Draft   SNMP Communications Services       April 1991


          packets.

          None of these documents have been made full Internet
          Standards. SNMP Over ISO and SNMP Over Ethernet are both
          Experimental protocols. SNMP Over IPX [6] is an Internet
          Draft. Only the SNMP Specification [1] is an Internet
          Standard.

          No single transport scheme can be considered the absolute best
          solution for all circumstances.  This note will argue that,
          except for a very small set of special circumstances,
          operating SNMP over UDP/IP is the optimal scheme.

          This document does not present a standard or a protocol for
          the Internet Community.  For production use in the Internet
          the SNMP and its required communication services are specified
          in [1].



          3.  Standardization

          Currently, the SNMP Specification [1] only specifies that the
          UDP protocol be used to exchange SNMP messages.  While the IAB
          may standardize other protocols for use in exchanging SNMP
          messages in the future, only UDP is currently standardized for
          this purpose.

          In order to claim full compliance with the SNMP Specification,
          an implementation would have to use UDP for SNMP message
          exchange.



          4.  Interoperability

          Interoperability is the degree to which the equipment produced
          by one vendor can can operate with equipment produced by
          another vendor.

          Related to Interoperability is compliance with a standard.
          Everything else being equal, a device that complies with some
          standard is more likely to be interoperable than a device that
          does not.






          Frank Kastenholz                                      [Page 2]


          Internet Draft   SNMP Communications Services       April 1991


          For commercial product development, the pros and cons of
          developing an interoperable product must be weighed and a
          choice made. Both engineering and marketing organizations
          participate in this process.

          The Internet is the single largest market for SNMP systems.  A
          large portion of SNMP systems will be developed with the
          Internet as a target environment.  Therefore, it may be
          expected that the Internet's needs and requirements will be
          the driving force for SNMP.  SNMP over UDP/IP is specified as
          the "Internet Standard" protocol.  Therefore, in order to
          operate in the Internet and be managed in that environment on
          a production basis, a device must support SNMP over UDP/IP.
          This situation will lead to SNMP over UDP/IP being the most
          common method of operating SNMP.  Therefore, the widest degree
          of interoperability and widest acceptance of a commercial
          product will be attained by operating SNMP over UDP/IP.

          The preponderance of UDP/IP based network management stations
          also strongly suggests that an agent should operate SNMP over
          UDP/IP.

          The results of the interoperability decision drive a number of
          technical decisions. If interoperability is desired, then SNMP
          must be operated over UDP/IP.



          5.  To Transport or Not To Transport

          A major issue is whether SNMP should run on top of a
          transport-layer protocol (such as UDP) or not.  Typically, the
          choice is to run over a transport/network/data link protocol
          or just run over the datalink.  In fact, several protocols
          have been published for operating SNMP over several different
          datalink and transport protocols.

          Operation of SNMP over a Transport and Network protocol stack
          is preferred.  These protocols provide at least five functions
          that are of vital importance to the movement of SNMP packets
          through a network:

          o Routing
               The network layer provides routing functions, which
               improves the overall utility of network management.  The





          Frank Kastenholz                                      [Page 3]


          Internet Draft   SNMP Communications Services       April 1991


               network has the ability to re-route packets around failed
               areas.  This allows network management to continue
               operating during localized losses of service (It should
               be noted that these losses of service occur not only
               because of failures, but also for non-failure reasons
               such as preventive maintenance).

          o Media Independence
               The network layer provides a high degree of media
               independence.  By using this capability, many different
               types of network elements may be managed.  Tying SNMP to
               a particular data link protocol limits the management
               scope of those SNMP entities to just those devices that
               use that datalink protocol.

          o End-to-End Checksum
               The end-to-end checksum provided by transport protocols
               improves the reliability of the data transfer.

          o Multiplexing/Demultiplexing
               Transport protocols provide multiplexing and
               demultiplexing services.  These services facilitate the
               many-to-many management relationships possible with SNMP.

          o Fragmentation and Reassembly
               This is related to media independence.  IP allows SNMP
               packets to transit media with differing MTU sizes.  This
               capability is not available for datalink specific
               transmission schemes.

               Fragmentation and Reassembly does reduce the overall
               robustness of network management since, if any single
               fragment is lost along the way, the operation will fail.
               The worse the network operates, the higher the
               probability that a fragment will get lost or delayed.
               For monitoring and data gathering while the network is
               operating normally, Fragmentation and Reassembly is not a
               problem. When the network is operating poorly (and the
               network operators are typically trying to diagnose and
               repair a failure), small packets should to be used,
               preventing the packet from being fragmented.

          There are other services and functions that are provided by a
          connection oriented transport.  These services and functions
          are not desired for SNMP.  A later section will explore this





          Frank Kastenholz                                      [Page 4]


          Internet Draft   SNMP Communications Services       April 1991


          issue in more detail.

          The main drawbacks that are cited with respect to using
          Transport and Network layers in the managed object are: a)
          Increased development time and b) Increased resource
          requirements.  These arguments are less than compelling.

          There are several excellent public domain or freely
          redistributable UDP/IP stacks that provide enough support for
          SNMP.  The effort required to port the essential components of
          one of these stacks is small compared to the overall effort of
          installing the SNMP software.

          The additional resources required in the managed object to
          support UDP/IP are minimal.  CPU resources are required only
          when actually transmitting or receiving a packet.  The largest
          single resource requirement of a UDP/IP is calculating the UDP
          checksum, which is very small compared to the cost of doing
          the ASN.1 encoding/decoding, Object Identifier lookup, and so
          on.

          The author has personal knowledge of a UDP/IP stack that was
          developed expressly for the purpose of supporting SNMP. This
          stack requires less than 4Kb of code space.  It is a
          minimalist implementation of UDP/IP in that it is "just
          enough" so support SNMP. This stack supports UDP, IP, ARP, and
          handles ICMP redirect and echo request messages.  Furthermore,
          this stack was developed by a single person in approximately
          two months.  Obviously, neither the development effort nor the
          memory requirements are large.

          The network overhead of using UDP/IP is relatively small.  A
          UDP/IP header requires 28 octets (assuming no IP options).
          Since the UDP is connectionless, it will generate no overhead
          traffic of its own (such as TCP SYNs, FINs, and ACKs).


          The growing popularity of internetworking outside of The
          Internet mandates that SNMP operate over, at least, a network
          layer protocol.  These internetworks consist of a number of
          networks all connected together with routers. In order to
          traverse a router, a packet must be one of the network layer
          protocols that the router understands.  Therefore, for SNMP
          management to be deployed in an internetwork, the SNMP
          entities in that internetwork must use a network layer





          Frank Kastenholz                                      [Page 5]


          Internet Draft   SNMP Communications Services       April 1991


          protocol.  SNMP over a datalink can not traverse a router.


          There are some circumstances where running SNMP over some
          datalink is appropriate.

          There are schemes are under development to provide Out-Of-Band
          (OOB) management access to network devices.  This OOB access
          is typically provided over point-to-point or dial-up
          connections.  Since these connections are dedicated to OOB
          network management and go directly from the network management
          station to the managed device, a Transport/Network protocol
          may not be necessary.

          Using a Transport/Network protocol on these links may be
          easier from a development point of view though.  It is
          probably a simple configuration operation to have the
          management station's IP use a serial port rather than the
          "normal" (e.g., Ethernet) port for traffic destined for a
          particular node.

          If the Out-Of-Band link is also used as a "primary" route to
          some nodes, then the functions of a network-layer are
          required. These functions are readily supplied by using
          UDP/IP.

          For a datalink interface and driver (e.g., a PC Ethernet
          interface card) that must be manageable independent of the
          higher level protocol suite (which might NOT be manageable),
          operating SNMP directly over the datalink is reasonable.  It
          is not known, a priori, what higher-level protocol services
          may be available, so those services can not be used.  If an
          arbitrary choice is made for example, to put in an elementary
          UDP/IP stack, then there may be two independent UDP/IPs in the
          system (which is undesireable as this would require two IP
          addresses per managed node), or a new protocol stack will be
          introduced into the environment.



          6.  Connection Oriented vs. Connectionless

          While this section primarily addresses itself to transport
          layer issues, its basic discussion of connection oriented vs
          connectionless applies to any layer which provides





          Frank Kastenholz                                      [Page 6]


          Internet Draft   SNMP Communications Services       April 1991


          communication services for SNMP.

          For SNMP, connectionless transport service (UDP) is specified
          in the Protocol Specification [1].  This choice was made after
          careful study and consideration by the original SNMP
          developers.

          The prime motivation of this choice is that SNMP must continue
          to operate (if at all possible) when the network is operating
          at its worst.  For other applications, such as Telnet or FTP,
          the user can always "try again later" if the network is
          operating poorly. On the other hand, the major purpose of a
          network management protocol is to fix the network when it is
          operating poorly so the "try again later" strategy is useless.

          By using a connectionless transport protocol, SNMP takes on
          the responsibility of reliable data transmission (A SNMP
          application may time out outstanding requests and either
          retransmit them or abort them as appropriate).  However, the
          SNMP requires these functions only of the sender of a Request
          PDU (get, getNext, or Set), which typically is a network
          management station.  Since the Agent only generates responses,
          it need not perform any of these functions.  This vastly
          reduces the resource and functional requirements on the Agent.

          If a connection oriented transport is used, then a fundamental
          design choice must be made with respect to connection
          maintenance:.

          (1)  Keep a connection open to each managed object on the
               network,

          (2)  Establish and tear down connections on a per-operation
               basis, or

          (3)  Keep a fixed number of connections open and, when another
               connection is needed, use some algorithm (e.g., LRU) to
               select one for closing and opening to the new agent.

          All of these alternatives pose severe problems, and because of
          them, each is undesirable.

          The first option reduces the amount of resources required to
          perform a single operation in that the connection
          establishment and termination cost is "amortized" over many





          Frank Kastenholz                                      [Page 7]


          Internet Draft   SNMP Communications Services       April 1991


          operations.  On the other hand, keeping a connection open
          implies that the management station needs to maintain a large
          number of connection records (in the hundreds or even
          thousands).  Furthermore, if either side of the connection
          engages in "keep-alives" (even though such behavior is frowned
          upon), a large amount of traffic will be generated, consuming
          a large amount of network resources, all for no gain.

          The second option reduces the amount of idle resources such as
          connection records, but vastly increases the amount of
          resources required to perform an operation.  A connection must
          be established, the request Message sent and the response
          returned, and then the connection closed for each operation.
          For a TCP, this would typically require 10 separate packet
          transfers plus the TCP Time-Wait (see the Appendix for
          details).

          In the face of pathological network problems, a connection
          oriented transport protocol may simply cease to operate
          because the probability of getting all of these packets
          through reduces to a very small number.

          The third option requires that the management station maintain
          connection usage information in order to implement the LRU
          algorithm.  This excessively complicates the management
          station.  Furthermore, this option tends to reduce to the
          second option when doing health check polling for a number of
          agents that is large compared to the number of supported
          connections.


          A connection oriented transport protocol may provide services
          that are undesirable or unneeded by SNMP.

          For example, one application of network management is to poll
          nodes to determine if they are up or not.  When a node is up,
          it makes little difference whether SNMP operates over TCP or
          UDP.  However, if the node goes down then TCP will eventually
          close the connection.  Every poll request must then be
          translated into a TCP Open request while the managed node is
          down.  Once the node comes up, the send must then be done.

          For connection oriented transports, the transport ACK does not
          necessarily indicate delivery of data to the destination
          application process (for TCP, see section 2.6 of [4]).  The





          Frank Kastenholz                                      [Page 8]


          Internet Draft   SNMP Communications Services       April 1991


          SNMP would still need its own timeout/retry procedure to
          ensure that the SNMP software actually got the packet.

          A connection oriented transport such as TCP provides flow
          control for the data stream.  Because of the lock-step nature
          of SNMP protocol exchanges, this is not a service that SNMP
          requires.


          Architectural purists may argue that an "Application" layer
          entity (SNMP) must not perform operations that are properly
          the realm of the Transport layer (timeouts, retransmissions,
          and so on).  While architecturally pure, this line of
          reasoning is not relevant.  The network management
          applications and protocols are monitoring the "health" of the
          network and, as a result, have the best information and are in
          the best position to adapt their own behavior to the state of
          the network, and thereby, continuing operations in the face of
          network adversity.



          7.  Which Protocol

          The final point of discussion is the actual choice of a
          protocol to support SNMP.

          If a device is destined for use in the Internet then it must
          operate SNMP over UDP/IP.

          If the device is operating in some other protocol environment,
          then SNMP ought to use the transport services that are native
          to that environment.  It may make very little sense to
          introduce a new protocol stack into a network in order to
          provide just one service.  For example, it could require that
          the network operations staff understand and be able to
          administer and operate two protocol stacks, that hosts and
          routers understand both protocols, and so on.  It may also be
          bureaucratically impossible to introduce UDP/IP into the
          environment (the "We are only a FOONET shop - if it doesn't
          speak FOONET, we don't want it" argument).

          References [2] and [6] are experimental standards for
          operating SNMP over IPX and OSI respectively, In these
          environments, those standards ought to be adhered to.





          Frank Kastenholz                                      [Page 9]


          Internet Draft   SNMP Communications Services       April 1991


          8.  Security Considerations

          Security issues are not discussed in this memo.



          9.  Appendix

          This appendix details the TCP packet transfers required to
          perform a single SNMP operation assuming that the connection
          is established only for that operation and that a single SNMP
          operation (e.g., get request) is performed.  We also assume
          that all operations are "normal" i.e., that there are no lost
          packets, no simultaneous opens, no half opens, and no
          simultaneous closes. We also ignore the possibility of TCP
          segmentation and IP fragmentation.

          The nomenclature used to illustrate the packet transactions is
          the same as that used in the TCP Specification [4].


              Packet  Management                         Managed
              Number  Station                            Object
                               Connection Open...
               1         >--<CTL=SYN>----------------------->
               2         <--<CTL=SYN,ACK>-------------------<
               3         >--<CTL=ACK>----------------------->
                           Connection now open,
                           SNMP Request is sent.
               4         >--<DATA=SNMP Request>------------->
                           Response comes back
               5         <--<DATA=SNMP Response, CTL=ACK>---<
               6         >--<CTL=ACK>----------------------->
                           Operation is complete,
                           Management station initiates the
                           close.
               7         >--<CTL=FIN,ACK>------------------->
               8         <--<CTL=ACK>-----------------------<
               9         <--<CTL=FIN,ACK>-------------------<
              10         >--<CTL=ACK>----------------------->
                          Wait 2 MSL
                          Connection now closed.








          Frank Kastenholz                                     [Page 10]


          Internet Draft   SNMP Communications Services       April 1991


          Some optimizations are possible IF the TCP has knowledge of
          the type of operation.  However, a general purpose TCP would
          not be tuned to SNMP operations so those optimizations would
          not be done.



          10.  References

          [1]  Case, J., M. Fedor, M. Schoffstall, and J. Davin, A
               Simple Network Management Protocol, Internet Working
               Group Request for Comments 1157, Network Information
               Center, SRI International, Menlo Park, California, May
               1990.

          [2]  Rose, M.T., SNMP over OSI, Internet Working Group Request
               for Comments 1161, Network Information Center, SRI
               International, Menlo Park, California, June 1990.

          [3]  Schoffstall, M.L., Davin, C., Fedor, M., Case, J.D., SNMP
               over Ethernet Internet Working Group Request for Comments
               1089, Network Information Center, SRI International,
               Menlo Park, California, February, 1989.

          [4]  Postel, J.B., Transmission Control Protocol Internet
               Working Group Request for Comments 793, Network
               Information Center, SRI International, Menlo Park,
               California, September 1981.

          [5]  Postel, J.B. User Datagram Protocol Internet Working
               Group Request for Comments 768, Network Information
               Center, SRI International, Menlo Park, California, August
               1980.

          [6]  Wormley, R., SNMP Over IPX, Internet Draft, August 1990.

          [7]  Defense Advanced Research Projects Agency, Internet
               Activities Board.  IAB Official Protocol Standards
               Internet Working Group Request for Comments 1140, Network
               Information Center, SRI International, Menlo Park,
               California, May 1990.

          [8]  V. Cerf, IAB Recommendations for the Development of
               Internet Network Management Standards.  Internet Working
               Group Request for Comments 1052.  Network Information





          Frank Kastenholz                                     [Page 11]


          Internet Draft   SNMP Communications Services       April 1991


               Center, SRI International, Menlo Park, California,
               (April, 1988).

          [9]  M.T. Rose and K. McCloghrie, Structure and Identification
               of Management Information for TCP/IP-based internets,
               Internet Working Group Request for Comments 1155.
               Network Information Center, SRI International, Menlo
               Park, California, (May, 1990).

          [10] K. McCloghrie and M.T. Rose, Management Information Base
               for Network Management of TCP/IP-based internets,
               Internet Working Group Request for Comments 1156.
               Network Information Center, SRI International, Menlo
               Park, California, (May, 1990).



          11.  Acknowledgements

          The author wishes to thank Jeff Case, Chuck Davin and Keith
          McCloghrie for their technical and editorial contributions to
          this document.



          12.  Author's Address

          Frank Kastenholz
          Clearpoint Research Corporation
          35 Parkwood Drive
          Hopkinton Mass 01748
          Phone: (508)435-2000
          Email: kasten@europa.clearpoint.com

















          Frank Kastenholz                                     [Page 12]


          Internet Draft   SNMP Communications Services       April 1991


          Table of Contents


          1 Status of This Memo ...................................    1
          2 Introduction ..........................................    1
          3 Standardization .......................................    2
          4 Interoperability ......................................    2
          5 To Transport or Not To Transport ......................    3
          6 Connection Oriented vs. Connectionless ................    6
          7 Which Protocol ........................................    9
          8 Security Considerations ...............................   10
          9 Appendix ..............................................   10
          10 References ...........................................   11
          11 Acknowledgements .....................................   12
          12 Author's Address .....................................   12



































          Frank Kastenholz                                     [Page ii]


Html markup produced by rfcmarkup 1.129d, available from https://tools.ietf.org/tools/rfcmarkup/