[Docs] [txt|pdf|xml|html] [Tracker] [WG] [Email] [Diff1] [Diff2] [Nits]

Versions: (draft-davari-tictoc-1588overmpls) 00 01 02 03 04 05 06 07

TICTOC Working Group                                           S. Davari
Internet-Draft                                                   A. Oren
Intended status: Standards Track                          Broadcom Corp.
Expires: December 17, 2013                                     M. Bhatia
                                                              P. Roberts
                                                          Alcatel-Lucent
                                                              L. Montini
                                                              L. Martini
                                                           Cisco Systems
                                                           June 15, 2013


            Transporting Timing messages over MPLS Networks
                   draft-ietf-tictoc-1588overmpls-05

Abstract

   This document defines the method for transporting Timing messages
   such as PTP and NTP over an MPLS network.  The method allows for the
   easy identification of these PDUs at the port level to allow for port
   level processing of these PDUs in both LERs and LSRs.

   The basic idea is to transport Timing messages inside dedicated MPLS
   LSPs.  These LSPs only carry Timing messages and possibly Control and
   Management packets, but they do not carry customer traffic.

   Two methods for transporting Timing messages over MPLS are defined.
   The first method is to transport Timing messages directly over the
   dedicated MPLS LSP via UDP/IP encapsulation, which is suitable for
   MPLS networks.  The second method is to transport Timing messages
   inside a PW via Ethernet encapsulation.

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on December 17, 2013.



Davari, et al.          Expires December 17, 2013               [Page 1]


Internet-Draft        Transporting Timing over MPLS            June 2013


Copyright Notice

   Copyright (c) 2013 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  5

   2.  Terminology  . . . . . . . . . . . . . . . . . . . . . . . . .  7

   3.  Problem Statement  . . . . . . . . . . . . . . . . . . . . . .  8

   4.  Timing over MPLS Architecture  . . . . . . . . . . . . . . . .  9

   5.  Dedicated LSPs for Timing messages . . . . . . . . . . . . . . 12

   6.  Timing over LSP Encapsulation  . . . . . . . . . . . . . . . . 13
     6.1.  Timing over UDP/IP over MPLS Encapsulation . . . . . . . . 13
     6.2.  Timing over PW Encapsulation . . . . . . . . . . . . . . . 13
     6.3.  Other Timing Encapsulation methods . . . . . . . . . . . . 14

   7.  Timing message Processing  . . . . . . . . . . . . . . . . . . 15

   8.  Protection and Redundancy  . . . . . . . . . . . . . . . . . . 16

   9.  ECMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

   10. PHP  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

   11. Entropy  . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

   12. OAM, Control and Management  . . . . . . . . . . . . . . . . . 20

   13. QoS Considerations . . . . . . . . . . . . . . . . . . . . . . 21

   14. FCS and Checksum Recalculation . . . . . . . . . . . . . . . . 22



Davari, et al.          Expires December 17, 2013               [Page 2]


Internet-Draft        Transporting Timing over MPLS            June 2013


   15. Behavior of LER/LSR  . . . . . . . . . . . . . . . . . . . . . 23
     15.1. Behavior of Timing-capable/aware LER . . . . . . . . . . . 23
     15.2. Behavior of Timing-capable/aware LSR . . . . . . . . . . . 23
     15.3. Behavior of non-Timing-capable/aware LSR . . . . . . . . . 24

   16. Other considerations . . . . . . . . . . . . . . . . . . . . . 25

   17. Security Considerations  . . . . . . . . . . . . . . . . . . . 26

   18. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 27

   19. IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 28

   20. References . . . . . . . . . . . . . . . . . . . . . . . . . . 29
     20.1. Normative References . . . . . . . . . . . . . . . . . . . 29
     20.2. Informative References . . . . . . . . . . . . . . . . . . 29

   Appendix 1.  Routing extensions for Timing-aware Routers . . . . . 32

   Appendix 2.  Signaling Extensions for Creating Timing LSPs . . . . 33

   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 34





























Davari, et al.          Expires December 17, 2013               [Page 3]


Internet-Draft        Transporting Timing over MPLS            June 2013


   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC2119 [RFC2119].

   When used in lower case, these words convey their typical use in
   common language, and are not to be interpreted as described in
   RFC2119 [RFC2119].












































Davari, et al.          Expires December 17, 2013               [Page 4]


Internet-Draft        Transporting Timing over MPLS            June 2013


1.  Introduction

   The objective of Precision Time Protocol (PTP) and Network Timing
   Protocol (NTP) are to synchronize independent clocks running on
   separate nodes of a distributed system.

   [IEEE-1588] defines PTP messages for frequency, phase and time
   synchronization.  The PTP messages include PTP PDUs over UDP/IP
   (Annex D and E of [IEEE-1588]) and PTP PDUs over Ethernet (Annex F of
   [IEEE-1588]).  This document defines mapping and transport of the PTP
   messages defined in [IEEE-1588] over MPLS/MPLS-TP networks.  PTP
   defines several clock types: ordinary clocks, boundary clocks, end-
   to-end transparent clocks, and peer-to-peer transparent clocks.
   Transparent clocks require intermediate nodes to update correction
   field inside PTP message that reflects the transit time in the node.

   [RFC5905] defines NTP messages for clock and time synchronization.
   The PTP messages (PDUs) are transported over UDP/IP.  This document
   defines mapping and transport of the NTP messages defined in
   [RFC5905] over MPLS networks.

   One key attribute of all of these Timing messages is that the Time
   stamp processing should occur as close as possible to the actual
   transmission and reception at the physical port interface.  This
   targets optimal time and/or frequency recovery by avoiding variable
   delay introduced by queues internal to the clocks.

   To facilitate the fast and efficient recognition of Timing messages
   at the port level when the Timing messages are carried over MPLS
   LSPs, this document defines the specific encapsulations that should
   be used.  In addition, it can be expected that there will exist LSR/
   LERs where only a subset of the physical ports will have the port-
   based Timing message processing capabilities.  In order to ensure
   that the LSPs carrying Timing packets always enter and exit ports
   with this capability, routing extensions are defined to advertise
   this capability on a port basis and to allow for the establishment of
   LSPs that only transit such ports.  While this path establishment
   restriction may be applied only at the LER Ingress and/or egress
   ports, it becomes more important when using transparent clock capable
   LSRs in the path.

   Port based Timing message processing involves Timing message
   recognition.  Once the Timing messages are recognized they can be
   modified based on the reception or transmission Time-stamp.

   This document provides two methods for transporting Timing messages
   over MPLS.  One is applicable to MPLS environment and the other one
   is applicable to MPLS/MPLS-TP environment



Davari, et al.          Expires December 17, 2013               [Page 5]


Internet-Draft        Transporting Timing over MPLS            June 2013


   The solution involves transporting Timing messages over dedicated
   LSPs called Timing LSPs.  These LSPs carry Timing messages and MAY
   carry Management and control messages, but not data plane client
   traffic.  Timing LSPs can be established statically or via signaling.
   Extensions to control plane (OSPF, ISIS, etc.) is required to enable
   routers to distribute their Timing processing capabilities over MPLS
   to other routers.  However such extensions are outside the scope of
   this document.

   When signaling is used to setup the PTP LSP, Extensions to signaling
   protocols (e.g., RSVP-TE) are required for establishing PTP LSPs.
   However such extensions are outside the scope of this document.

   While the techniques included herein allow for the establishment of
   paths optimized to include Time-stamping capable links, the
   performance of the Slave clocks is outside the scope of this
   document.

   At the time of publishing this specification, Transparent Clocking
   (TC) is only defined for PTP.  Therefore at this time any part of
   this specification that talks about Transparent Clocking applies only
   to PTP.





























Davari, et al.          Expires December 17, 2013               [Page 6]


Internet-Draft        Transporting Timing over MPLS            June 2013


2.  Terminology

   1588: The timing and synchronization as defined by IEEE 1588.

   NTP: The timing and synchronization protocol defined by IETF RFC-1305
   and RFC-5905.

   PTP: The timing and synchronization protocol used by 1588.

   Master Clock: The source of 1588 timing to a set of slave clocks.

   Master Port: A port on a ordinary or boundary clock that is in Master
   state.  This is the source of timing toward slave ports.

   Slave Clock: A receiver of 1588 timing from a master clock.

   Slave Port: A port on a boundary clock or ordinary clock that is
   receiving timing from a master clock.

   Ordinary Clock: A device with a single PTP port.

   Transparent Clock.  A device that measures the time taken for a PTP
   event message to transit the device and then updates the
   correctionField of the message with this transit time.

   Boundary Clock: A device with more than one PTP port.  Generally
   boundary clocks will have one port in slave state to receive timing
   and then other ports in master state to re-distribute the timing.

   PTP LSP: An LSP dedicated to carry PTP messages

   PTP PW: A PW within a PTP LSP that is dedicated to carry PTP
   messages.

   CW: Pseudowire Control Word

   LAG: Link Aggregation

   ECMP: Equal Cost Multipath

   CF: Correction Field, a field inside certain PTP messages (message
   type 0-3)that holds the accumulative transit time inside intermediate
   switches

   Timing messages: Timing Protocol messages that are exchanged between
   routers in order to establish a synchronized clock.





Davari, et al.          Expires December 17, 2013               [Page 7]


Internet-Draft        Transporting Timing over MPLS            June 2013


3.  Problem Statement

   [IEEE-1588] has defined methods for transporting PTP messages over
   Ethernet and IP networks.  [RFC5905] has defined the method of
   transporting NTP messages over IP networks.  There is a need to
   transport Timing messages over MPLS networks while supporting the
   Transparent Clock (TC), Boundary Clock (BC) and Ordinary Clock (OC)
   functionality in the LER and LSRs in the MPLS network.

   There are multiple ways of transporting Timing over MPLS.  However,
   there is a requirement to limit the possible encapsulation options to
   simplify the Timing message identification and processing required at
   the port level.

   When Timing-awareness is needed, Timing messages should not be
   transported over LSPs or PWs that are carrying customer traffic
   because LSRs perform Label switching based on the top label in the
   stack.  To detect Timing messages inside such LSPs require special
   hardware to do deep packet inspection at line rate.  Even if such
   hardware exists, the payload can't be deterministically identified by
   LSRs because the payload type is a context of the PW label, and the
   PW label and its context are only known to the Edge routers (PEs/
   LERs); LSRs dont know what is a PWs payload (Ethernet, ATM, FR, CES,
   etc).  Even if one restricts an LSP to only carry Ethernet PWs, the
   LSRs dont have the knowledge of whether PW Control Word (CW) is
   present or not and therefore can not deterministically identify the
   payload.

   A generic method is defined in this document that does not require
   deep packet inspection at line rate, and can deterministically
   identify Timing messages.  This method can be used to detect Timing
   Messages in both one-step and two-step clock implementations of
   ordinary, boundary and transparent clocks.


















Davari, et al.          Expires December 17, 2013               [Page 8]


Internet-Draft        Transporting Timing over MPLS            June 2013


4.  Timing over MPLS Architecture

   Timing messages are exchange between Timing ports on ordinary and
   boundary clocks.  Boundary clocks terminate the Timing messages and
   act as master for other boundary clocks or for slave clocks.  End-to-
   End Transparent clocks do not terminate the Timing messages but they
   do modify the contents of the Timing messages as they transit across
   the transparent clock.

   Master/Slave clocks (OCs), Boundary Clocks (BC) and Transparent Clock

   (TC) could be implemented in either LERs or LSRs.

   An example is shown in Figure 1, where the LERs act as Ordinary Clock
   (OC) and are the initiating/terminating point for Timing messages.
   The ingress LER encapsulates the Timing messages in Timing LSP and
   the Egress LER terminates the Timing LSP.  The LSRs act as
   Transparent Clock (TC) and just update the Timing field in the Timing
   messages.


      +--------+     +-------+     +-------+     +-------+     +--------+
      |Switch, |     |       |     |       |     |       |     |Switch, |
      | Router |-----|  LER  |-----|  LSR  |-----|  LER  |-----| Router |
      |        |     |  OC   |     |  TC   |     |  OC   |     |        |
      +--------+     +-------+     +-------+     +-------+     +--------+
                     /                                 \
      +-------+     /                                   \     +-------+
      |  LER  |    /                                     \    |  LER  |
      | Master|---/                                       \---| Slave |
      | Clock |                                               | Clock |
      +-------+                                               +-------+

     Figure (1) - Deployment example 1 of timing over MPLS network

   Another example is shown in Figure2, where LERs terminate the Timing
   messages received from switch/routers that are outside of the MPLS
   network acting as OC or BC.  In this example LERs regenerate the
   clock and initiate timing messages encapsulated in Timing LSP toward
   the MPLS network, while the LSRs act as Transparent Clock (TC) and
   just update the Timing field in the Timing messages, which are
   already encapsulated in Timing LSPs.









Davari, et al.          Expires December 17, 2013               [Page 9]


Internet-Draft        Transporting Timing over MPLS            June 2013


     +--------+     +-------+     +-------+     +-------+     +--------+
     |Switch, |     |       |     |       |     |       |     |Switch, |
     | Router |-----|  LER  |-----|  LSR  |-----|  LER  |-----| Router |
     | OC/BC  |     |  BC   |     |  TC   |     |  BC   |     | OC/BC  |
     +--------+     +-------+     +-------+     +-------+     +--------+

     Figure (2) - Deployment example 2 of timing over MPLS network


   Another example is shown in Figure 3, where LERs do not terminate the
   Timing messages received from switch/routers that are outside of the
   MPLS network acting as OC, TC or BC.  The LERs act as TC and update
   the Timing field in the Timing messages as they transit the LER,
   while encapsulating them in timing LSP.  The LSRs also act as
   Transparent Clock (TC) and just update the Timing field in the Timing
   messages which are already encapsulated in Timing LSPs.

      +--------+     +-------+     +-------+     +-------+     +--------+
      |Switch, |     |       |     |       |     |       |     |Switch, |
      | Router |-----|  LER  |-----|  LSR  |-----|  LER  |-----| Router |
      |OC/TC/BC|     |  TC   |     |  TC   |     |  TC   |     |OC/TC/BC|
      +--------+     +-------+     +-------+     +-------+     +--------+

    Figure (3) - Deployment example 3 of timing over MPLS network

   Another example is shown in Figure 4, where LERs and LSRs support
   Boundary Clocks.  A single-hop LSP is created between two adjacent
   LSRs engaged in BC operation.  Other methods such as PTP transport
   over Ethernet MAY be used for transporting timing messages if the
   link between the two routers is Ethernet.

     +--------+     +-------+     +-------+     +-------+     +--------+
     |Switch, |     |       |     |       |     |       |     |Switch, |
     | Router |-----|  LER  |-----|  LSR  |-----|  LER  |-----| Router |
     | OC/BC  |     |  BC   |     |  BC   |     |  BC   |     | OC/BC  |
     +--------+     +-------+     +-------+     +-------+     +--------+

   Figure (4) - Deployment example 3 of timing over MPLS network

   An MPLS domain MAY serve multiple customers.  In these cases the MPLS
   domain (maintained by a service provider) may provide timing services
   to multiple customers, each having their own Timing domain.

   The Timing over MPLS architecture assumes full mesh of Timing LSPs
   between all LERs supporting this specification.  It supports
   Point-to- point (VPWS) and Multipoint (VPLS) services.  This means
   that a customer may purchase a Point-to-point Timing service between
   two customer sites or a Multipoint Timing service between more than



Davari, et al.          Expires December 17, 2013              [Page 10]


Internet-Draft        Transporting Timing over MPLS            June 2013


   two customer sites.

   The Timing over MPLS architecture supports P2P or P2MP Timing LSPs.
   This means that the Timing Multicast messages such as PTP Multicast
   event messages can be transported over P2MP Timing LSP or be
   replicated and transported over many P2P Timing LSPs.

   Timing messages, that do not require Time stamping or Correction
   Field update MAY be transported over Timing LSPs to simplify hardware
   and software.

   PTP Announce messages that determine the Timing LSP terminating point
   behavior such as BC/OC/TC SHOULD be transported over the Timing LSP
   to simplify hardware and software.





































Davari, et al.          Expires December 17, 2013              [Page 11]


Internet-Draft        Transporting Timing over MPLS            June 2013


5.  Dedicated LSPs for Timing messages

   Many methods have been considered for identifying the Timing messages
   when they are encapsulated in MPLS such as using GAL/G-ACH or a new
   reserved label.  These methods were not attractive since they either
   required deep packet inspection at line rate in the intermediate LSRs
   or they required use of a scarce new reserved label.  Also one of the
   goals was to reuse existing OAM mechanisms.

   The method defined in this document can be used by LER and LSRs to
   identify Timing messages in MPLS tunnels by just looking at the top
   label in the MPLS label stack, which only carry Timing messages as
   well as OAM, but not data plane client traffic.

   Compliant implementations MUST use dedicated LSPs to carry Timing
   messages over MPLS.  These LSPs are herein referred to as "Timing
   LSPs" and the labels associated with these LSPs as "Timing LSP
   labels".  The Timing LSPs that runs between Ingress and Egress LERs
   MUST be co-routed.  Alternatively, a single bidirectional co-routed
   LSP can be used.

   Co-routing of the two directions is required to limit the difference
   in the delays in the Master clock to Slave clock direction compared
   to the Slave clock to Master clock direction.  The Timing LSP MAY be
   MPLS/MPLS-TP LSP.

   The Timing LSPs could be configured or signaled via RSVP-TE/GMPLS.
   New Extensions to RSVP-TE/GMPLS TLVs are required; however they are
   outside the scope of this document.

   The Timing LSPs MAY carry essential MPLS/MPLS-TP OAM traffic such as
   BFD and LSP Ping but the LSP data plane client plane traffic MUST be
   Timing packets only.


















Davari, et al.          Expires December 17, 2013              [Page 12]


Internet-Draft        Transporting Timing over MPLS            June 2013


6.  Timing over LSP Encapsulation

   This document defines two methods for carrying Timing messages over
   MPLS.  The first method is carrying UDP/IP encapsulated Timing
   messages over Timing LSPs, and the second method, is carrying
   Ethernet encapsulated Timing messages over Ethernet PWs inside Timing
   LSPs.

6.1.  Timing over UDP/IP over MPLS Encapsulation

   The simplest method of transporting Timing messages over MPLS is to
   encapsulate Timing PDUs in UDP/IP and then encapsulate them in Timing
   LSP.  This format is shown in Figure 4.


                    +----------------------+
                    |   Timing LSP Label   |
                    +----------------------+
                    |        IPv4/6        |
                    +----------------------+
                    |         UDP          |
                    +----------------------+
                    |     Timing PDU       |
                    +----------------------+

      Figure (4) - Timing over UDP/IP over MPLS Encapsulation


   This encapsulation is very simple and is useful when the network
   between Timing Master Clock and Slave Clock is MPLS network.

   In order for an LER/LSR to process Timing messages, the Timing LSP
   Label must be at the top label of the label stack.  The LER/LSR MUST
   know that the Timing LSP Label is used for carrying Timing messages.
   This can be accomplished via static configuration or via RSVP-TE
   signaling.

   The UDP/IP encapsulation of PTP MUST follow Annex D and E of
   [IEEE-1588].  While the UDP/IP encapsulation of NTP MUST follow
   [RFC5905].

6.2.  Timing over PW Encapsulation

   Another method of transporting Timing over MPLS networks is by
   encapsulating Timing PDUs in PW which in turn is transported over
   Timing LSPs.  In case of PTP, Ethernet PW encapsulation [RFC4448],
   shown in Fig 5(A) MUST be used and the Ethernet encapsulation of PTP
   MUST follow Annex F of [IEEE-1588].



Davari, et al.          Expires December 17, 2013              [Page 13]


Internet-Draft        Transporting Timing over MPLS            June 2013


   The RAW mode or Tagged mode defined in [RFC4448] MAY be used and the
   Payload MUST have 0, 1, or 2 VLAN tags (S-VLAN and C-VLAN).  The
   Timing over PW encapsulation MUST use the Control Word (CW) as
   specified in [RFC4448] to ensure proper detection of PTP messages
   inside the MPLS packets for Timing over LSP and Timing over PW
   encapsulation.  The use of Sequence Number in the CW is optional.

   Timing over PW encapsulation for NTP MUST use NTP over UDP/IP over PW
   (the IP PW discussed in [RFC4447]) shown in Fig 5(B).

                    +----------------+  +----------------+
                     |Timing LSP Label|  |Timing LSP Label|
                     +----------------+  +----------------+
                     |    PW Label    |  |    PW Label    |
                     +----------------+  +----------------+
                     |  Control Word  |  |      IP        |
                     +----------------+  +----------------+
                     |    Ethernet    |  |      UDP       |
                     |     Header     |  +----------------+
                     +----------------+  |   Timing PDU   |
                     |S-VLAN(Optional)|  |                |
                     +----------------+  +----------------+
                     |C-VLAN(Optional)|        (B)
                     +----------------+
                     |   Timing PDU   |
                     |                |
                     +----------------+
                            (A)

              Figure (5) - Timing over PW Encapsulations

   In order for an LSR to process PTP messages, the top label of the
   label stack (the Tunnel Label) MUST be a Timing label.

6.3.  Other Timing Encapsulation methods

   In future other timing encapsulation methods may be introduced, such
   as a new shim header after the Bottom of Stack to carry the Timing
   information.  Such new encapsulations are outside the scope of this
   document.











Davari, et al.          Expires December 17, 2013              [Page 14]


Internet-Draft        Transporting Timing over MPLS            June 2013


7.  Timing message Processing

   Each Timing protocol such as PTP and NTP, define their set of Timing
   messages.  For example PTP defines SYNC, DELAY_REQ, DELAY_RESP,
   FOLLOW_UP, etc messages.

   Some of the Timing messages require time stamping or correction field
   update at port level and some dont.  It is the job of the LER/LSR to
   parse the timing message and find out the type of the Timing message
   and decide whether and how to Time- stamp it (e.g., BC) or update
   correction field(e.g., TC).

   For example the following PTP messages (called Event messages)
   require time-stamping or correction field update:

   o  SYNC

   o  DELAY_REQ (Delay Request)

   o  PDELAY_REQ (Peer Delay Request)

   o  PDELAY_RESP (Peer Delay Response)

   SYNC and DELAY_REQ are exchanged between Master Clock and Slave Clock
   and MUST be transported over PTP LSPs.  PDELAY_REQ and PDELAY_RESP
   are exchanged between adjacent PTP clocks (i.e.  Master, Slave,
   Boundary, or Transparent) and SHOULD be transported over single hop
   PTP LSPs.  If Two Step PTP clocks are present, then the FOLLOW_UP,
   and PDELAY_RESP_FOLLOW_UP messages MUST also be transported over the
   PTP LSPs.

   For a given instance of 1588 protocol, SYNC and DELAY_REQ MUST be
   transported over two PTP LSPs that are in opposite directions.  These
   PTP LSPs, which are in opposite directions MUST be congruent and co-
   routed.  Alternatively, a single bidirectional co-routed LSP can be
   used.

   Except as indicated above for the two-step PTP clocks, Non-Event PTP
   message types do not need to be processed by intermediate routers.
   These message types MAY be carried in PTP Tunnel LSPs.











Davari, et al.          Expires December 17, 2013              [Page 15]


Internet-Draft        Transporting Timing over MPLS            June 2013


8.  Protection and Redundancy

   In order to ensure continuous uninterrupted operation of slave
   clocks, usually as a general practice, slave clocks (or ports) track
   redundant master clocks.

   It is the responsibility of the network operator to ensure that
   physically disjoint Timing LSPs are established between a slave clock
   (or port) and redundant master clocks (or ports).

   When a slave clock (or port) listens to redundant master clocks or
   ports, any prolonged Timing LSP outage will trigger the slave clock
   or port to switch to a redundant master clock or port.

   LSP/PW protection such as Linear protection Switching (1:1, 1+1),
   Ring protection switching or MPLS Fast Reroute (FRR) generally switch
   alternative path that usually cause a change in delay, which if
   undetected by slave clock can reduce accuracy of the slave clock.

   Therefore protection switching MAY be used, as long as phase jumps
   upon switchover due to differences in path latency are detected and
   compensated for (such compensation not being required if BCs or peer-
   peer TCs are used throughout).

   Note that any protection or reroute mechanism that adds additional
   MPLS label to the label stack, such as Facility Backup Fast Reroute,
   MUST ensure that the pushed label is also a Timing Label to ensure
   recognition of the MPLS frame as containing Timing messages, as it
   transits the backup path.






















Davari, et al.          Expires December 17, 2013              [Page 16]


Internet-Draft        Transporting Timing over MPLS            June 2013


9.  ECMP

   To ensure the optimal operation of slave clocks and avoid error
   introduced by forward and reverse path delay asymmetry, the physical
   path for Timing messages from master clock to slave Clock and vice
   versa must be the same for all Event Timing messages listed in
   section 7.

   Therefore the Timing LSPs MUST not be subject to ECMP (Equal Cost
   Multipath).









































Davari, et al.          Expires December 17, 2013              [Page 17]


Internet-Draft        Transporting Timing over MPLS            June 2013


10.  PHP

   To ensure that the label on the top of the label stack is the Timing
   LSP Label, PHP MUST not be used.















































Davari, et al.          Expires December 17, 2013              [Page 18]


Internet-Draft        Transporting Timing over MPLS            June 2013


11.  Entropy

   To ensure all Timing messages in a Timing LSP take the same path,
   Entropy Label MUST NOT be used for the Timing LSP[RFC6790] and
   Entropy Label MUST NOT be used for the PWs that are carried inside
   Timing LSP [RFC6391].













































Davari, et al.          Expires December 17, 2013              [Page 19]


Internet-Draft        Transporting Timing over MPLS            June 2013


12.  OAM, Control and Management

   In order to monitor Timing LSPs and their encapsulated PWs, they MUST
   be able to carry OAM and management messages.  These management
   messages MUST be differentiated from Timing messages via already
   defined IETF methods.

   For example BFD [RFC5880], [RFC5884] and LSP-Ping [RFC4389] MAY run
   over PTP LSPs via UDP/IP encapsulation or via GAL/G-ACH.  These
   Management protocols can easily be identified by the UDP Destination
   Port number or by GAL/G-ACH respectively.

   Also BFD, LSP-Ping and other management messages MAY run over the PWs
   encapsulated in Timing LSP via one of the defined VCCVs (Type 1, 3 or
   4) [RFC5085] (note that VCCV Type 2 using Router Alert Label is going
   to be deprecated by IETF).  In this case G-ACH, PW label (TTL=1) or
   GAL-ACH are used to identify such management messages.


































Davari, et al.          Expires December 17, 2013              [Page 20]


Internet-Draft        Transporting Timing over MPLS            June 2013


13.  QoS Considerations

   In network deployments where not every LSR/LER is Timing-aware, it is
   important to reduce the impact of the non-Timing-aware LSR/LERs on
   the timing recovery in the slave clock.  The Timing messages are time
   critical and must be treated with the highest priority.  Therefore
   Timing over MPLS messages must be treated with the highest priority
   in the routers.  This can be achieved by proper setup of Timing LSPs.

   It is recommended that the Timing LSPs are setup or configured
   properly to indicate EF-PHB [RFC3246]for the CoS and Green [RFC2697]
   for drop eligibility.







































Davari, et al.          Expires December 17, 2013              [Page 21]


Internet-Draft        Transporting Timing over MPLS            June 2013


14.  FCS and Checksum Recalculation

   When time-stamp generation and timing packet adjustment is performed
   near the physical port hardware, the process MUST include
   recalculation of the Ethernet FCS.  Also FCS retention for the
   payload Ethernet described in [RFC4720] MUST NOT be used.

   For UDP/IP encapsulation mode of Timing over MPLS, the UDP checksum
   may be required as per UDP transport standards.

   When UDP checksum is used, each Timing-aware LER/LSR must either
   incrementally update the UDP checksum after Time stamping or
   Correction Field update or verify the UDP checksum on reception from
   upstream and recalculate the checksum completely on transmission to
   downstream node after Time stamping or Correction Field update.




































Davari, et al.          Expires December 17, 2013              [Page 22]


Internet-Draft        Transporting Timing over MPLS            June 2013


15.  Behavior of LER/LSR

   Timing-capable/aware LERs and LSRs are routers that have one or more
   interfaces that can perform Timing operations (OC/BC/TC) on Timing
   packets and are configured to do so.  Timing-capable/aware LERs and
   LSRs can advertise their Timing-capability per-interface via control
   plane such as OSPF or IS-IS.  The Timing-capable/aware LERs can then
   signals Timing LSPs via RSVP-TE signaling.  Alternatively the Timing
   capability of LER and LSRs may be configured in a centralized
   controller and the Timing LSP may be setup using manual configuration
   or other methods such as SDN.

15.1.  Behavior of Timing-capable/aware LER

   When a Timing-capable/aware LER behaves as a Transparent clock and
   receives a Timing message from a Timing-capable/aware non-MPLS
   interface, the LER updates the Correction Field (CF) and encapsulates
   and forwards the timing message over previously established Timing
   LSP.  Also when a Timing message is received from a Timing-capable/
   aware MPLS interface, LER updates the Correction Filed (CF) and
   decapsulates the MPLS encapsulation and forwards the timing message
   to a non-MPLS interface.

   When a Timing-capable/aware LER behaves as a Boundary clock and
   receives a Timing message from a Timing-capable/aware non MPLS
   interface, the LER Timestamps the Timing packet and sends it to the
   LERs Boundary clock processing module.  Also when a Timing message is
   received from a Timing- capable/aware MPLS interface, the LER
   Timestamps the Timing packet and sends it to the LERs Boundary clock
   processing module.

   When a Timing-capable/aware LER behaves as an Ordinary Clock toward
   the MPLS network, and receives a Timing message from a Timing-
   capable/aware MPLS interface, the LER Timestamps the Timing packet
   and sends it to the LERs Ordinary clock processing module.

15.2.  Behavior of Timing-capable/aware LSR

   When a Timing-capable/aware LSR behaves as a Transparent clock and
   receives a Timing message from a Timing-capable/aware MPLS interface,
   The LSR updates the Correction Filed (CF) and forwards the timing
   message over another MPLS interface.

   When a Timing-capable/aware LSR behaves as a Boundary clock and
   receives a Timing message from a Timing-capable/aware MPLS interface.
   The LSR performs the functions of a Boundary Clock in terminating the
   received Timing message and re-generating a new timing message over
   another (or the same) MPLS interface.



Davari, et al.          Expires December 17, 2013              [Page 23]


Internet-Draft        Transporting Timing over MPLS            June 2013


15.3.  Behavior of non-Timing-capable/aware LSR

   It is most beneficial when all LSRs in the path of a Timing LSP be
   timing-Capable/aware LSRs.  This would ensure the highest quality
   time and clock synchronization by Timing Slave Clocks.  However, this
   specification does not mandate that all LSRs in path of a Timing LSP
   be Timing- capable/aware.

   Non-Timing-capable/aware LSRs just switch the packets encapsulated in
   Timing LSPs and dont perform any Timing operation (TC or BC).
   However as explained in QoS section the Timing over MPLS packets MUST
   be still be treated with the highest priority based on their Traffic
   Class (TC) marking.






































Davari, et al.          Expires December 17, 2013              [Page 24]


Internet-Draft        Transporting Timing over MPLS            June 2013


16.  Other considerations

   [IEEE-1588] defines an optional peer-to-peer Transparent clocking
   that requires peer delay measurement between two adjacent Timing-
   capable/ aware routers/switches.  Peer delay measurement messages
   need to be time stamped and terminated by the Timing-capable/aware
   routers/ switches.  This means that two adjacent LSRs may be engaged
   in a peer delay measurement.

   For transporting such peer delay measurement messages a single-hop
   LSP SHOULD to be created between the two adjacent LSRs engaged in
   peer delay measurement to carry peer delay measurement messages.
   Other methods such as PTP transport over Ethernet MAY be used for
   transporting peer delay measurement messages if the link between the
   two routers is Ethernet.

   In Peer-to-peer transparent clocking (P2P TC), a Timing-capable/ ware
   routers/switches MUST maintain a list of all the neighbors it needs
   to send a PDelay_Req to, where each neighbor corresponds to a timing
   LSP.

   The use of Explicit Null Label (Label= 0 or 2) is acceptable as long
   as either the Explicit Null label is the bottom of stack label
   (applicable only to UDP/IP encapsulation) or the label below the
   Explicit Null label is a PTP label.


























Davari, et al.          Expires December 17, 2013              [Page 25]


Internet-Draft        Transporting Timing over MPLS            June 2013


17.  Security Considerations

   MPLS PW security considerations in general are discussed in [RFC3985]
   and [RFC4447],and those considerations also apply to this document.

   An experimental security protocol is defined in [IEEE-1588].The PTP
   security extension and protocol provides group source authentication,
   message integrity, and replay attack protection for PTP messages.

   When the MPLS network (provider network) serves multiple customers,
   it is important to maintain and process each customers clock and
   Timing messages separately from other customers to ensure there is no
   cross- customer effect.  For example if an LER BC is synchronized to
   a specific grandmaster, belonging to customer A, then the LER MUST
   use that BC clock only for customer A to ensure that customer A
   cannot attack other customers by manipulating its time.

   Timing messages MAY be encrypted or authenticated, provided that the
   LERs/LSRs that are Timing capable/aware can authenticate/ decrypt the
   timing messages.































Davari, et al.          Expires December 17, 2013              [Page 26]


Internet-Draft        Transporting Timing over MPLS            June 2013


18.  Acknowledgements

   The authors would like to thank Ron Cohen, Yaakov Stein, Tal Mizrahi,
   Stefano Ruffini, Peter Meyer, and other members of IETF for reviewing
   and providing feedback on this draft.














































Davari, et al.          Expires December 17, 2013              [Page 27]


Internet-Draft        Transporting Timing over MPLS            June 2013


19.  IANA Considerations

   There are no IANA requirements in this specification.
















































Davari, et al.          Expires December 17, 2013              [Page 28]


Internet-Draft        Transporting Timing over MPLS            June 2013


20.  References

20.1.  Normative References

   [IEEE-1588]
              IEEE 1588-2008, "IEEE Standard for a Precision Clock
              Synchronization Protocol for Networked Measurement and
              Control Systems".

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3985]  Bryant, S. and P. Pate, "Pseudo Wire Emulation Edge-to-
              Edge (PWE3) Architecture", RFC 3985, March 2005.

   [RFC4389]  Thaler, D., Talwar, M., and C. Patel, "Neighbor Discovery
              Proxies (ND Proxy)", RFC 4389, April 2006.

   [RFC4447]  Martini, L., Rosen, E., El-Aawar, N., Smith, T., and G.
              Heron, "Pseudowire Setup and Maintenance Using the Label
              Distribution Protocol (LDP)", RFC 4447, April 2006.

   [RFC4448]  Martini, L., Rosen, E., El-Aawar, N., and G. Heron,
              "Encapsulation Methods for Transport of Ethernet over MPLS
              Networks", RFC 4448, April 2006.

   [RFC4720]  Malis, A., Allan, D., and N. Del Regno, "Pseudowire
              Emulation Edge-to-Edge (PWE3) Frame Check Sequence
              Retention", RFC 4720, November 2006.

   [RFC5085]  Nadeau, T. and C. Pignataro, "Pseudowire Virtual Circuit
              Connectivity Verification (VCCV): A Control Channel for
              Pseudowires", RFC 5085, December 2007.

   [RFC5880]  Katz, D. and D. Ward, "Bidirectional Forwarding Detection
              (BFD)", RFC 5880, June 2010.

   [RFC5884]  Aggarwal, R., Kompella, K., Nadeau, T., and G. Swallow,
              "Bidirectional Forwarding Detection (BFD) for MPLS Label
              Switched Paths (LSPs)", RFC 5884, June 2010.

20.2.  Informative References

   [I-D.ietf-pwe3-fat-pw]
              Bryant, S., Filsfils, C., Drafz, U., Kompella, V., Regan,
              J., and S. Amante, "Flow Aware Transport of Pseudowires
              over an MPLS Packet Switched Network",
              draft-ietf-pwe3-fat-pw-07 (work in progress), July 2011.



Davari, et al.          Expires December 17, 2013              [Page 29]


Internet-Draft        Transporting Timing over MPLS            June 2013


   [ISO]      ISO/IEC 10589:1992, "Intermediate system to Intermediate
              system routeing information exchange protocol for use in
              conjunction with the Protocol for providing the
              Connectionless-mode Network Service (ISO 8473)".

   [RFC1195]  Callon, R., "Use of OSI IS-IS for routing in TCP/IP and
              dual environments", RFC 1195, December 1990.

   [RFC2328]  Moy, J., "OSPF Version 2", STD 54, RFC 2328, April 1998.

   [RFC2697]  Heinanen, J. and R. Guerin, "A Single Rate Three Color
              Marker", RFC 2697, September 1999.

   [RFC3246]  Davie, B., Charny, A., Bennet, J., Benson, K., Le Boudec,
              J., Courtney, W., Davari, S., Firoiu, V., and D.
              Stiliadis, "An Expedited Forwarding PHB (Per-Hop
              Behavior)", RFC 3246, March 2002.

   [RFC3630]  Katz, D., Kompella, K., and D. Yeung, "Traffic Engineering
              (TE) Extensions to OSPF Version 2", RFC 3630,
              September 2003.

   [RFC3784]  Smit, H. and T. Li, "Intermediate System to Intermediate
              System (IS-IS) Extensions for Traffic Engineering (TE)",
              RFC 3784, June 2004.

   [RFC4970]  Lindem, A., Shen, N., Vasseur, JP., Aggarwal, R., and S.
              Shaffer, "Extensions to OSPF for Advertising Optional
              Router Capabilities", RFC 4970, July 2007.

   [RFC4971]  Vasseur, JP., Shen, N., and R. Aggarwal, "Intermediate
              System to Intermediate System (IS-IS) Extensions for
              Advertising Router Information", RFC 4971, July 2007.

   [RFC5120]  Przygienda, T., Shen, N., and N. Sheth, "M-ISIS: Multi
              Topology (MT) Routing in Intermediate System to
              Intermediate Systems (IS-ISs)", RFC 5120, February 2008.

   [RFC5305]  Li, T. and H. Smit, "IS-IS Extensions for Traffic
              Engineering", RFC 5305, October 2008.

   [RFC5329]  Ishiguro, K., Manral, V., Davey, A., and A. Lindem,
              "Traffic Engineering Extensions to OSPF Version 3",
              RFC 5329, September 2008.

   [RFC5340]  Coltun, R., Ferguson, D., Moy, J., and A. Lindem, "OSPF
              for IPv6", RFC 5340, July 2008.




Davari, et al.          Expires December 17, 2013              [Page 30]


Internet-Draft        Transporting Timing over MPLS            June 2013


   [RFC5905]  Mills, D., Martin, J., Burbank, J., and W. Kasch, "Network
              Time Protocol Version 4: Protocol and Algorithms
              Specification", RFC 5905, June 2010.

   [RFC6391]  Bryant, S., Filsfils, C., Drafz, U., Kompella, V., Regan,
              J., and S. Amante, "Flow-Aware Transport of Pseudowires
              over an MPLS Packet Switched Network", RFC 6391,
              November 2011.

   [RFC6790]  Kompella, K., Drake, J., Amante, S., Henderickx, W., and
              L. Yong, "The Use of Entropy Labels in MPLS Forwarding",
              RFC 6790, November 2012.







































Davari, et al.          Expires December 17, 2013              [Page 31]


Internet-Draft        Transporting Timing over MPLS            June 2013


1.  Routing extensions for Timing-aware Routers

   MPLS-TE routing relies on extensions to OSPF [RFC2328] [RFC5340] and
   IS-IS [ISO] [RFC1195] in order to advertise Traffic Engineering (TE)
   link information used for constraint-based routing.

   Indeed, it is useful to advertise data plane TE router link
   capabilities, such as the capability for a router to be Timing-aware.
   This capability MUST then be taken into account during path
   computation to prefer or even require links that advertise themselves
   as Timing-aware.  In this way the path can ensure the entry and exit
   points into the LERs and, if desired, the links into the LSRs are
   able to perform port based time-stamping thus minimizing their impact
   on the performance of the slave clock.

   extensions are required to OSPF and IS-IS in order to advertise
   Timing-aware capabilities of a link.  Such extensions are outside the
   scope of this document; however such extension SHOULD be able to
   signal the following information per Router Link:

   o  Capable of processing PTP, NTP or other Timing flows

   o  Capable of performing Transparent Clock operation

   o  Capable of performing Boundary Clock operation


























Davari, et al.          Expires December 17, 2013              [Page 32]


Internet-Draft        Transporting Timing over MPLS            June 2013


2.  Signaling Extensions for Creating Timing LSPs

   RSVP-TE signaling MAY be used to setup the timing LSPs.  When RSVP-TE
   is used to setup Timing LSPs, some information that indicates that
   the LSP is carrying Timing flows MUST be included in the new
   Extensions to RSVP-TE:

   The following information MAY also be included in the new Extensions
   to RSVP-TE:

   o  Offset from Bottom of Stack (BoS) to the start of the Time-stamp
      field

   o  Number of VLANs in case of PW encapsulation

   o  Timestamp field Type

      *  Correction Field, Timestamp

   o  Timestamp Field format

      *  64-bit PTPv1, 80-bit PTPv2, 32-bit NTP, 64-bit NTP, 128-bit
         NTP, etc.

   Note that in case the above optional information is signaled with
   RSVP-TE for a Timing LSP, all the Timing packets carried in that LSP
   must have the same signaled characteristics.  For example if
   Timestamp format is signaled as 64-bit PTPv1, then all Timing packets
   must use 64-bit PTPv1 time-stamp.






















Davari, et al.          Expires December 17, 2013              [Page 33]


Internet-Draft        Transporting Timing over MPLS            June 2013


Authors' Addresses

   Shahram Davari
   Broadcom Corp.
   San Jose, CA  95134
   USA

   Email: davari@broadcom.com


   Amit Oren
   Broadcom Corp.
   San Jose, CA  95134
   USA

   Email: amito@broadcom.com


   Manav Bhatia
   Alcatel-Lucent
   Bangalore,
   India

   Email: manav.bhatia@alcatel-lucent.com


   Peter Roberts
   Alcatel-Lucent
   Kanata,
   Canada

   Email: peter.roberts@alcatel-lucent.com


   Laurent Montini
   Cisco Systems
   San Jose CA
   USA

   Email: lmontini@cisco.com











Davari, et al.          Expires December 17, 2013              [Page 34]


Internet-Draft        Transporting Timing over MPLS            June 2013


   Luca
   Cisco Systems
   San Jose CA
   USA

   Email: lmartini@cisco.com













































Davari, et al.          Expires December 17, 2013              [Page 35]


Html markup produced by rfcmarkup 1.129c, available from https://tools.ietf.org/tools/rfcmarkup/