[Docs] [txt|pdf] [Tracker] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01 02 03 04 05 06 07 08 09 RFC 3630

Network Working Group                                            D. Katz
Internet Draft                                          Juniper Networks
Category: Standards Track                                       D. Yeung
Expires: April 2003                                     Procket Networks
draft-katz-yeung-ospf-traffic-09.txt                         K. Kompella
                                                        Juniper Networks
                                                            October 2002


            Traffic Engineering Extensions to OSPF Version 2
                             *** Draft ***


Status

   This document is an Internet-Draft and is in full conformance with
   all provisions of Section 10 of RFC2026.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet- Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.


Copyright Notice

   Copyright (C) The Internet Society (2002).  All Rights Reserved.













Katz, Yeung, Kompella        Standards Track                    [Page 1]

Internet Draft           TE Extensions to OSPFv2            October 2002


Abstract

   This document describes extensions to the OSPF protocol version 2 to
   support intra-area Traffic Engineering, using Opaque Link State
   Advertisements.


Changes

   (This section to be removed before publication).

   Per comments from the OSPF WG mailing list, the following changes
   were made:

    - State that operation over multi-access networks with more than two
      TE devices is not expressly forbidden.
    - Fix figure in 2.3.1.
    - Specify that a Remote Interface IP Address sub-TLV is optional for
      a multi-access link.
































Katz, Yeung, Kompella        Standards Track                    [Page 2]

Internet Draft           TE Extensions to OSPFv2            October 2002


1. Introduction

   This document specifies a method of adding traffic engineering
   capabilities to OSPF Version 2 [1].  The architecture of traffic
   engineering is described in [2].  The semantic content of the
   extensions is essentially identical to the corresponding extensions
   to IS-IS [3].  It is expected that the traffic engineering extensions
   to OSPF will continue to mirror those in IS-IS.

   The extensions provide a way of describing the traffic engineering
   topology (including bandwidth and administrative constraints) and
   distributing this information within a given OSPF area.  This
   topology does not necessarily match the regular routed topology,
   though this proposal depends on Network LSAs to describe multiaccess
   links.

1.1. Applicability

   Many of the extensions specified in this document are in response to
   the requirements stated in [2], and thus are referred to as "traffic
   engineering extensions", and are also commonly associated with MPLS
   Traffic Engineering.  A more accurate (albeit bland) designation is
   "extended link attributes", as what is proposed is simply to add more
   attributes to links in OSPF advertisements.

   The information made available by these extensions can be used to
   build an extended link state database just as router LSAs are used to
   build a "regular" link state database; the difference is that the
   extended link state database (referred to below as the traffic
   engineering database) has additional link attributes.  Uses of the
   traffic engineering database include:

      o monitoring the extended link attributes;
      o local constraint-based source routing; and
      o global traffic engineering.

   For example, an OSPF-speaking device can participate in an OSPF area,
   build a traffic engineering database, and thereby report on the
   reservation state of links in that area.

   In "local constraint-based source routing", a router R can compute a
   path from a source node A to a destination node B; typically, A is R
   itself, and B is specified by a "router address" (see below).  This
   path may be subject to various constraints on the attributes of the
   links and nodes that the path traverses, e.g., use green links that
   have unreserved bandwidth of at least 10Mbps.  This path could then
   be used to carry some subset of the traffic from A to B, forming a
   simple but effective means of traffic engineering.  How the subset of



Katz, Yeung, Kompella        Standards Track                    [Page 3]

Internet Draft           TE Extensions to OSPFv2            October 2002


   traffic is determined, and how the path is instantiated is beyond the
   scope of this document; suffice it to say that one means of defining
   the subset of traffic is "those packets whose IP destinations were
   learned from B", and one means of instantiating paths is using MPLS
   tunnels.  As an aside, note that constraint-based routing can be NP-
   hard, or even unsolvable, depending on the nature of the attributes
   and constraints and thus many implementations will use heuristics.
   Consequently, we don't attempt to sketch an algorithm here.

   Finally, for "global traffic engineering", a device can build a
   traffic engineering database, input a traffic matrix and an
   optimization function, crunch on the information, and thus compute
   optimal or near-optimal routing for the entire network.  The device
   can subsequently monitor the traffic engineering topology and react
   to changes by recomputing the optimal routes.

1.2. Limitations

   As mentioned above, this document specifies extensions and procedures
   for intra-area distribution of Traffic Engineering information.
   Methods for inter-area and inter-AS (Autonomous System) are not
   discussed here.

   The extensions specified in this document capture the reservation
   state of point-to-point links.  The reservation state of multiaccess
   links may not be accurately reflected, except in the special case
   that there are only two devices in the multiaccess subnetwork.
   Operation over multiaccess networks with more than two devices is not
   specifically prohibited.  More accurate description of the
   reservation state of multi-access networks is for further study.

   This document also does not support unnumbered links.  This
   deficiency is addressed in [4]; see also [5] and [6].

1.3. Conventions

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [7].












Katz, Yeung, Kompella        Standards Track                    [Page 4]

Internet Draft           TE Extensions to OSPFv2            October 2002


2. LSA Format

2.1. LSA type

   This extension makes use of the Opaque LSA [8].

   Three types of Opaque LSAs exist, each of which has different
   flooding scope.  This proposal uses only Type 10 LSAs, which have
   area flooding scope.

   One new LSA is defined, the Traffic Engineering LSA.  This LSA
   describes routers, point-to-point links, and connections to
   multiaccess networks (similar to a Router LSA).  For traffic
   engineering purposes, the existing Network LSA suffices for
   describing multiaccess links, so no additional LSA is defined for
   this purpose.

2.2. LSA ID

   The LSA ID of an Opaque LSA is defined as having eight bits of type
   and 24 bits of type-specific data.  The Traffic Engineering LSA uses
   type 1.  The remaining 24 bits are the Instance field, as follows:

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |       1       |                   Instance                    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The Instance field is an arbitrary value used to maintain multiple
   Traffic Engineering LSAs.  A maximum of 16777216 Traffic Engineering
   LSAs may be sourced by a single system.  The LSA ID has no
   topological significance.

2.3. LSA Format Overview

2.3.1. LSA Header

   The Traffic Engineering LSA starts with the standard LSA header:












Katz, Yeung, Kompella        Standards Track                    [Page 5]

Internet Draft           TE Extensions to OSPFv2            October 2002


      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |            LS age             |    Options    |      10       |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |       1       |                   Instance                    |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                     Advertising Router                        |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                     LS sequence number                        |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |         LS checksum           |             Length            |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

2.3.2. TLV Header

   The LSA payload consists of one or more nested Type/Length/Value
   (TLV) triplets for extensibility.  The format of each TLV is:

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |              Type             |             Length            |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                            Value...                           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The Length field defines the length of the value portion in octets
   (thus a TLV with no value portion would have a length of zero).  The
   TLV is padded to four-octet alignment;  padding is not included in
   the length field (so a three octet value would have a length of
   three, but the total size of the TLV would be eight octets).  Nested
   TLVs are also 32-bit aligned.  Unrecognized types are ignored.

   This memo defines Types 1 and 2.  See the IANA Considerations section
   for allocation of new Types.

2.4. LSA payload details

   An LSA contains one top-level TLV.

   There are two top-level TLVs defined:

     1 - Router Address
     2 - Link






Katz, Yeung, Kompella        Standards Track                    [Page 6]

Internet Draft           TE Extensions to OSPFv2            October 2002


2.4.1. Router Address TLV

   The Router Address TLV specifies a stable IP address of the
   advertising router that is always reachable if there is any
   connectivity to it.  This is typically implemented as a "loopback
   address"; the key attribute is that the address does not become
   unusable if an interface is down.  In other protocols this is known
   as the "router ID," but for obvious reasons this nomenclature is
   avoided here.  If a router advertises BGP routes with the BGP next
   hop attribute set to the BGP router ID, then the Router Address
   SHOULD be the same as the BGP router ID.

   If IS-IS is also active in the domain, this address can also be used
   to compute the mapping between the OSPF and IS-IS topologies.  For
   example, suppose a router R is advertising both IS-IS and OSPF
   Traffic Engineering LSAs, and suppose further that some router S is
   building a single Traffic Engineering Database (TED) based on both
   IS-IS and OSPF TE information.  R may then appear as two separate
   nodes in S's TED; however, if both the IS-IS and OSPF LSAs generated
   by R contain the same Router Address, then S can determine that the
   IS-IS TE LSA and the OSPF TE LSA from R are indeed from a single
   router.

   The router address TLV is type 1, and has a length of 4, and the
   value is the four octet IP address.  It must appear in exactly one
   Traffic Engineering LSA originated by a router.

2.4.2. Link TLV

   The Link TLV describes a single link.  It is constructed of a set of
   sub-TLVs.  There are no ordering requirements for the sub-TLVs.

   Only one Link TLV shall be carried in each LSA, allowing for fine
   granularity changes in topology.

   The Link TLV is type 2, and the length is variable.

   The following sub-TLVs are defined:













Katz, Yeung, Kompella        Standards Track                    [Page 7]

Internet Draft           TE Extensions to OSPFv2            October 2002


     1 - Link type (1 octet)
     2 - Link ID (4 octets)
     3 - Local interface IP address (4 octets)
     4 - Remote interface IP address (4 octets)
     5 - Traffic engineering metric (4 octets)
     6 - Maximum bandwidth (4 octets)
     7 - Maximum reservable bandwidth (4 octets)
     8 - Unreserved bandwidth (32 octets)
     9 - Administrative group (4 octets)

   This memo defines sub-Types 1 through 9.  See the IANA Considerations
   section for allocation of new sub-Types.

   The Link Type and Link ID sub-TLVs are mandatory, i.e., must appear
   exactly once.  All other sub-TLVs defined here may occur at most
   once.  These restrictions need not apply to future sub-TLVs.
   Unrecognized sub-TLVs are ignored.

   Various values below use the (32 bit) IEEE Floating Point format.
   For quick reference, this format is as follows:

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |S|    Exponent   |                  Fraction                   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   where S is the sign; Exponent is the exponent base 2 in "excess 127"
   notation; and Fraction is the mantissa - 1, with an implied binary
   point in front of it.  Thus the above represents the value
        (-1)**(S) * 2**(Exponent-127) * (1 + Fraction)

   For more details, refer to [9].

2.5. Sub-TLV Details

2.5.1. Link Type

   The Link Type sub-TLV defines the type of the link:

       1 - Point-to-point
       2 - Multiaccess

   The Link Type sub-TLV is TLV type 1, and is one octet in length.







Katz, Yeung, Kompella        Standards Track                    [Page 8]

Internet Draft           TE Extensions to OSPFv2            October 2002


2.5.2. Link ID

   The Link ID sub-TLV identifies the other end of the link.  For point-
   to-point links, this is the Router ID of the neighbor.  For
   multiaccess links, this is the interface address of the designated
   router.  The Link ID is identical to the contents of the Link ID
   field in the Router LSA for these link types.

   The Link ID sub-TLV is TLV type 2, and is four octets in length.

2.5.3. Local Interface IP Address

   The Local Interface IP Address sub-TLV specifies the IP address(es)
   of the interface corresponding to this link.  If there are multiple
   local addresses on the link, they are all listed in this sub-TLV.

   The Local Interface IP Address sub-TLV is TLV type 3, and is 4N
   octets in length, where N is the number of local addresses.

2.5.4. Remote Interface IP Address

   The Remote Interface IP Address sub-TLV specifies the IP address(es)
   of the neighbor's interface corresponding to this link.  This and the
   local address are used to discern multiple parallel links between
   systems.  If the Link Type of the link is Multiaccess, the Remote
   Interface IP Addess is set to 0.0.0.0; alternatively, an
   implementation MAY choose not to send this sub-TLV.

   The Remote Interface IP Address sub-TLV is TLV type 4, and is 4N
   octets in length, where N is the number of neighbor addresses.

2.5.5. Traffic Engineering Metric

   The Traffic Engineering Metric sub-TLV specifies the link metric for
   traffic engineering purposes.  This metric may be different than the
   standard OSPF link metric.  Typically, this metric is assigned by a
   network admistrator.

   The Traffic Engineering Metric sub-TLV is TLV type 5, and is four
   octets in length.

2.5.6. Maximum Bandwidth

   The Maximum Bandwidth sub-TLV specifies the maximum bandwidth that
   can be used on this link in this direction (from the system
   originating the LSA to its neighbor), in IEEE floating point format.
   This is the true link capacity.  The units are bytes per second.




Katz, Yeung, Kompella        Standards Track                    [Page 9]

Internet Draft           TE Extensions to OSPFv2            October 2002


   The Maximum Bandwidth sub-TLV is TLV type 6, and is four octets in
   length.

2.5.7. Maximum Reservable Bandwidth

   The Maximum Reservable Bandwidth sub-TLV specifies the maximum
   bandwidth that may be reserved on this link in this direction, in
   IEEE floating point format.  Note that this may be greater than the
   maximum bandwidth (in which case the link may be oversubscribed).
   This SHOULD be user-configurable; the default value should be the
   Maximum Bandwidth.  The units are bytes per second.

   The Maximum Reservable Bandwidth sub-TLV is TLV type 7, and is four
   octets in length.

2.5.8. Unreserved Bandwidth

   The Unreserved Bandwidth sub-TLV specifies the amount of bandwidth
   not yet reserved at each of the eight priority levels, in IEEE
   floating point format.  The values correspond to the bandwidth that
   can be reserved with a setup priority of 0 through 7, arranged in
   increasing order with priority 0 occurring at the start of the sub-
   TLV, and priority 7 at the end of the sub-TLV.  The initial values
   (before any bandwidth is reserved) are all set to the Maximum
   Reservable Bandwidth.  Each value will be less than or equal to the
   Maximum Reservable Bandwidth.  The units are bytes per second.

   The Unreserved Bandwidth sub-TLV is TLV type 8, and is 32 octets in
   length.

2.5.9. Administrative Group

   The Administrative Group sub-TLV contains a 4-octet bit mask assigned
   by the network administrator.  Each set bit corresponds to one
   administrative group assigned to the interface.  A link may belong to
   multiple groups.

   By convention the least significant bit is referred to as 'group 0',
   and the most significant bit is referred to as 'group 31'.

   The Administrative Group is also called Resource Class/Color [2].

   The Administrative Group sub-TLV is TLV type 9, and is four octets in
   length.







Katz, Yeung, Kompella        Standards Track                   [Page 10]

Internet Draft           TE Extensions to OSPFv2            October 2002


3. Elements of Procedure

   Routers shall originate Traffic Engineering LSAs whenever the LSA
   contents change, and whenever otherwise required by OSPF (an LSA
   refresh, for example).  Note that this does not mean that every
   change must be flooded immediately; an implementation MAY set
   thresholds (for example, a bandwidth change threshold) that trigger
   immediate flooding, and initiate flooding of other changes after a
   short time interval.  In any case, the origination of Traffic
   Engineering LSAs SHOULD be rate-limited to at most one every
   MinLSInterval [1].

   Upon receipt of a changed Traffic Engineering LSA or Network LSA
   (since these are used in traffic engineering calculations), the
   router should update its traffic engineering database.  No SPF or
   other route calculations are necessary.


4. Compatibility Issues

   There should be no interoperability issues with routers that do not
   implement these extensions, as the Opaque LSAs will be silently
   ignored.

   The result of having routers that do not implement these extensions
   is that the traffic engineering topology will be missing pieces;
   however, if the topology is connected, TE paths can still be
   calculated and ought to work.


5. Normative References

   [1] Moy, J., "OSPF Version 2", RFC 2328, April 1998.

   [4] Kompella, K., Rekhter, Y., et al, "OSPF Extensions in Support of
       Generalized MPLS," work in progress.

   [6] Kompella, K., and Y. Rekhter, "Signalling Unnumbered Links in
       RSVP-TE," work in progress.

   [7] Bradner, S., "Key words for use in RFCs to Indicate Requirement
       Levels", BCP 14, RFC 2119, March 1997.

   [8] Coltun, R., "The OSPF Opaque LSA Option," RFC 2370, July 1998.

   [9] IEEE, "IEEE Standard for Binary Floating-Point Arithmetic",
       Standard 754-1985, 1985 (ISBN 1-5593-7653-8).




Katz, Yeung, Kompella        Standards Track                   [Page 11]

Internet Draft           TE Extensions to OSPFv2            October 2002


6. Informative References

   [2] Awduche, D., et al, "Requirements for Traffic Engineering Over
   MPLS," RFC 2702, September 1999.

   [3] Smit, H. and T. Li, "ISIS Extensions for Traffic Engineering,"
   work in progress.

   [5] Kompella, K., Rekhter, Y., and A. Kullberg, "Signalling
   Unnumbered Links in CR-LDP," work in progress.

   [10] Narten, T., and H. Alvestrand, "Guidelines for Writing an IANA
   Considerations Section in RFCs", RFC 2434, BCP 26, October 1998.

   [11] Murphy, S., Badger, M., and B. Wellington, "OSPF with Digital
   Signatures", RFC 2154, June 1997.


7. Security Considerations

   This document specifies the contents of Opaque LSAs in OSPFv2.  As
   Opaque LSAs are not used for SPF computation or normal routing, the
   extensions specified here have no affect on IP routing.  Tampering
   with TE LSAs may have an effect on traffic engineering computations,
   however, and it is suggested that whatever mechanisms are used for
   securing the transmission of normal OSPF LSAs be applied equally to
   all Opaque LSAs, including the TE LSAs specified here.

   Note that the mechanisms in [1] and [11] apply to Opaque LSAs.  It is
   suggested that any future mechanisms proposed to secure/authenticate
   OSPFv2 LSA exchanges be made general enough to be used with Opaque
   LSAs.


8. IANA Considerations

   The top level Types in a TE LSA as well as Types for sub-TLVs in a TE
   Link TLV are to be registered with IANA.

   Following the guidelines set in [10], top level Types in TE LSAs from
   3 through 32767 are to be assigned by Expert Review (the said Expert
   to be decided by the IESG).  Types from 32768 through 65535 are
   reserved for Private Use.  In all cases, assigned values Types MUST
   be registered with IANA.

   Also, sub-Types of a TE Link TLV from 10 to 32767 are to be assigned
   by Expert Review; values from 32768 through 32772 are reserved for
   Private Use; and values from 32773 through 65535 are to be assigned



Katz, Yeung, Kompella        Standards Track                   [Page 12]

Internet Draft           TE Extensions to OSPFv2            October 2002


   First Come First Served.  In all cases, assigned values are to be
   registered with IANA.


9. Authors' Addresses

   Dave Katz
   Juniper Networks
   1194 N. Mathilda Ave.
   Sunnyvale, CA 94089 USA

   Phone:  +1 408 745 2000
   Email:  dkatz@juniper.net

   Derek M. Yeung
   Procket Networks, Inc.
   1100 Cadillac Court
   Milpitas, CA 95035 USA

   Phone:  +1 408 635-7900
   Email: myeung@procket.com

   Kireeti Kompella
   Juniper Networks
   1194 N. Mathilda Ave.
   Sunnyvale, CA 94089 USA

   Phone:  +1 408 745 2000
   Email:  kireeti@juniper.net


10. IPR Notices

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; neither does it represent that it
   has made any effort to identify any such rights.  Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11.  Copies of
   claims of rights made available for publication and any assurances of
   licenses to be made available, or the result of an attempt made to
   obtain a general license or permission for the use of such
   proprietary rights by implementors or users of this specification can
   be obtained from the IETF Secretariat.

   The IETF invites any interested party to bring to its attention any



Katz, Yeung, Kompella        Standards Track                   [Page 13]

Internet Draft           TE Extensions to OSPFv2            October 2002


   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard.  Please address the information to the IETF Executive
   Director.


11. Full Copyright Notice

   Copyright (C) The Internet Society (2002).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implmentation may be prepared, copied, published and
   distributed, in whole or in part, without restriction of any kind,
   provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the  purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.


















Katz, Yeung, Kompella        Standards Track                   [Page 14]


Html markup produced by rfcmarkup 1.111, available from https://tools.ietf.org/tools/rfcmarkup/