[Docs] [txt|pdf] [Tracker] [Email] [Diff1] [Diff2] [Nits] [IPR]

Versions: 00 01 02 03

Network Working Group                     Ping Pan (Juniper Networks)
Internet Draft                       Nischal Sheth (Juniper Networks)
Expiration Date: May 2002               Dave Cooper (Global Crossing)
Network Working Group                  George Swallow (Cisco Systems)
                                   Sanjay Wadhwa (Unisphere Networks)
                                                Ron Bonica (Worldcom)



               Detecting Data Plane Liveliness in RSVP-TE

                       draft-pan-lsp-ping-02.txt

Status of this Memo

This document is an Internet-Draft and is in full conformance with all
provisions of Section 10 of RFC2026.

Internet-Drafts are working documents of the Internet Engineering Task
Force (IETF), its areas, and its working groups.  Note that other groups
may also distribute working documents as Internet-Drafts.

Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time.  It is inappropriate to use Internet-Drafts as reference material
or to cite them other than as ``work in progress.''

The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt

The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.

Abstract

This document describes a simple and efficient mechanism that can be
used to detect data plane failures in MPLS LSP's. The proposed mechanism
requires a new optional RSVP object.  The processing overhead imposed on
LSR control plane is kept to minimum.


Sub-IP Summary ID

This document describes a simple and efficient mechanism that can be
used to detect data plane failures in MPLS LSP's. The proposed mechanism
requires a new optional RSVP object.  The processing overhead imposed on
LSR control plane is kept to minimum.




draft-pan-lsp-ping-02.txt                                       ^L[Page 1]


Internet Draft          draft-pan-lsp-ping-02.txt           October 2001


RELATED DOCUMENTS

May be found in the "references" section.

WHERE DOES IT FIT IN THE PICTURE OF THE SUB-IP WORK

Fits the MPLS box.

WHY IS IT TARGETED AT THIS WG

MPLS WG is currently looking at MPLS-specific error detection and
recovery mechanisms.  This work presents a simple mechanism to detect a
specific MPLS data plane failure, that cannot be detected by MPLS
control plane.  One possible cause of such failure may be due to memory
corruption.

JUSTIFICATION

The WG should consider this document, as it allows network operators to
detect MPLS LSP data plane failures in the network. This type of
failures had occurred in MPLS networks.



1. Introduction

   This document describes a simple and efficient mechanism that can be
   used to detect data plane failures in MPLS LSP's. The proposed
   mechanism requires a new optional RSVP object.  The processing
   overhead imposed on LSR control plane is kept to minimum.



2. Motivation

   When an LSP has failed to deliver user traffic, the failure cannot
   always be detected by the MPLS control plane.  In the case of this
   draft we are addressing the RSVP-TE component.  There is a need to
   provide a tool that would enable users to detect such traffic "black
   holes" within a reasonable period of time.  Such a tool should
   additionally have the following characteristics. It should not
   introduce a heavy processing overhead on LSR's.  It should not open
   the door to potential DOS attacks.  In this document, we describe a
   mechanism, termed "LSP-ping", that accomplishes these goals.







draft-pan-lsp-ping-02.txt                                       ^L[Page 2]


Internet Draft          draft-pan-lsp-ping-02.txt           October 2001


3. LSP-ping Extension


3.1. RSVP-TE Extension

   To test an LSP's liveliness, an ingress LSR sends LSP-ping messages
   that contains an LSP_ECHO object over the LSP being tested.  When an
   egress LSR receives the message, it needs to acknowledge the ingress
   LSR by copying the LSP_ECHO object into a RSVP Resv message.  The
   object has the following format:


         Class = LSP_ECHO  (use form 11bbbbbb for compatibility)

         C-Type = 1

         +-------------+-------------+-------------+-------------+
         |                   Source  Identifier                  |
         +-------------+-------------+-------------+-------------+

         Source Identifier

            This value is assigned by ingress LSR to uniquely identify
            the sending process.  This would allow an ingress LSR to
            identify the returned responses if there are multiple
            instances of LSP-ping running.



3.2. LSP-ping message

   During the LSP liveliness test, an ingress LSR sends probe packets to
   the egress LSR's control plane over the LSP that is being tested.
   This packet must be encapsulated in UDP with a well-known port
   number.  The reason for choosing UDP is described below.

   We call the UDP-encapsulated packet as "an LSP-ping message".  Each
   LSP-ping message must carry sufficient amount of information that can
   identify the testing LSP.  At minimum, it must contain an SESSION, an
   SENDER_TEMPLATE and an LSP_ECHO object.  The SESSION and
   SENDER_TEMPLATE object MUST use the format specified in [RSVP-TE].

   Each LSP-ping message has a common header and a set of RSVP objects.
   An LSP-ping message may look like the following:


         +-------------+-------------+-------------+-------------+
         |           Length          |          Reserved         |



draft-pan-lsp-ping-02.txt                                       ^L[Page 3]


Internet Draft          draft-pan-lsp-ping-02.txt           October 2001


         +-------------+-------------+-------------+-------------+
         //                    LSP_ECHO Object                  //
         +-------------+-------------+-------------+-------------+
         //                    SESSION Object                   //
         +-------------+-------------+-------------+-------------+
         //                SENDER_TEMPLATE Object               //
         +-------------+-------------+-------------+-------------+
         //                     padding....                     //
         +-------------+-------------+-------------+-------------+


   The common header consists of a length field, that is the LSP-ping
   message length including the common header itself, in bytes. The
   length value MUST satisfy the MTU constraint of the testing LSP.



4. Operation

   For the sake of brevity in the context of this document by "the
   control plane" we mean "the RSVP-TE component of the control plane".

   Consider an LSP between an ingress LSR and an egress LSR spanning
   multiple LSR hops.


4.1. Procedures at the ingress LSR

   Before initiating the liveliness test, the user must make sure that
   both ingress and egress LSR can support the LSR-ping.

   When an LSP needs to be tested, the ingress LSR sends ICMP
   ECHO_REQUEST messages [ICMP] over the LSP periodically.  The period
   is controlled by a timer.  The value of the time interval should be
   configurable.

   If there are multiple LSPs between the ingress and egress LSRs, the
   ECHO_REQUEST messages MUST be differentiated by using unique
   identifiers in the Identifier field of the ECHO_REQUEST message.

   If the ingress LSR does not receive ICMP ECHO_REPLY messages from the
   egress for a long period of time, it is likely that there is an LSP
   failure on either the forward path (from ingress to egress) or the
   reverse path (from egress to ingress), or both.

   When the ingress LSR suspects that the LSP may have failed and the
   RSVP control plane shows the LSP as operational, the ingress LSR MUST
   send LSP-ping messages to the egress over the LSP, periodically.  The



draft-pan-lsp-ping-02.txt                                       ^L[Page 4]


Internet Draft          draft-pan-lsp-ping-02.txt           October 2001


   value of the time interval should be configurable.

   The ingress LSR selects a unique Source_Identifer value for this
   particular test and places it in the LSP_ECHO object.  The ingress
   LSR includes the LSP_ECHO object along with the SESSION and
   SENDER_TEMPLATE objects of the LSP under test.

   If the ingress LSR does not receive an Resv message from the egress
   LSR that consists of an LSP_ECHO object within a period of time, it
   declares the LSP as "down".  At this point, the ingress LSR should
   apply the necessary procedures to fix the LSP.  This may include
   generating a message to network management, tearing-down and re-
   building the LSP, and/or rerouting user traffic to a backup LSP.

   During the test, ICMP ECHO_REQUEST and LSP-ping messages MUST set the
   IP TTL field to one in the IP header. This is to prevent the
   misbehavior at egress LSR's.

   To test an LSP that carries non-IP traffic, before injecting ICMP and
   LSP-ping messages into the LSP, the IPv4 Explicit NULL label should
   be prepended to such messages. The ingress and egress LSR's must
   follow the procedures defined in [LABEL-STACKING].



4.2. Procedures at the egress LSR

   When the egress LSR receives an ICMP ECHO_REQUEST message, it handles
   the message according to the procedures defined in [ICMP] (this is
   irrespective of whether the message is used for an LSP liveliness
   test or not).  It is possible that the ICMP processing is entirely
   done by the hardware or in the IP fast data path, thus, the initial
   ICMP "ping" messages have little impact on control plane's
   performance.

   When the egress LSR receives an LSP-ping message, it needs to deliver
   the message to the control plane. To avoid potential DOS attacks, it
   is recommended to regulate the LSP-ping traffic going to the control
   plane. A rate limiter should be applied to the well-known UDP port
   defined above.

   At the control plane, based on the RSVP SESSION and SENDER_TEMPLATE
   objects carried in the LSP-ping message, the LSR can find the
   corresponding LSP in its RSVP-TE database.  The LSR then checks to
   see if the Resv message for this LSP contains an LSP_ECHO object with
   the same Source_Identifier value.  If not, the LSR adds or updates
   the LSP_ECHO object and refreshes the Resv message.




draft-pan-lsp-ping-02.txt                                       ^L[Page 5]


Internet Draft          draft-pan-lsp-ping-02.txt           October 2001


4.3. Procedures for the intermediate LSR's

   At intermediate LSRs, normal RSVP processing procedures will cause
   the LSP_ECHO object to be forwarded as RSVP messages are refreshed.

   At the LSR's that support LSP-ping, the Resv messages that carry the
   LSP_ECHO object MUST be delivered upstream immediately.

   Note that an intermediate LSR using RSVP refresh reduction [RSVP-
   REFRESH], the new or changed LSP_ECHO object will cause the LSR to
   classify the RSVP message as a trigger message.



5. Security Considerations

   The mechanism introduced in this document can prevent potential DOS
   attacks.  The security  considerations pertaining to the original
   RSVP protocol remain relevant.



6. IANA Guidelines

   IANA [RFC-IANA] will assign a UDP port to LSP-ping packet, and a RSVP
   c-class to LSP_ECHO object.



7. Intellectual Property Considerations

   Juniper Networks, Inc. is seeking patent protection on technology
   described in this Internet-Draft. If technology in this Internet-
   Draft is adopted as a standard, Juniper Networks agrees to license,
   on reasonable and non-discriminatory terms, any patent rights it
   obtains covering such technology to the extent necessary to comply
   with the standard.














draft-pan-lsp-ping-02.txt                                       ^L[Page 6]


Internet Draft          draft-pan-lsp-ping-02.txt           October 2001


8. Acknowledgments

   This is the outcome of many discussions among many people, that also
   include Manoj Leelanivas, Paul Traina, Kireeti Kompella, Yakov
   Rekhter, Der-Hwa Gan, Brook Bailey and Eric Rosen.



9. References

   [ICMP] J. Postel, "Internet Control Message Protocol", RFC792.

   [RSVP] R. Braden, Ed., et al, "Resource ReSerVation protocol (RSVP)
   -- version 1 functional specification," RFC2205.

   [RSVP-TE] D. Awduche, et al, "RSVP-TE: Extensions to RSVP for LSP
   tunnels" Internet Draft.

   [LABEL-STACKING] E. Rosen, et al, "MPLS Label Stack Encoding",
   RFC3032.

   [RSVP-REFRESH] L. Berger, et al, "RSVP Refresh Overhead Reduction
   Extensions", RFC2961.

   [RFC-IANA] T. Narten and H. Alvestrand, "Guidelines for Writing an
   IANA Considerations Section in RFCs", RFC 2434.



10. Author Information





















draft-pan-lsp-ping-02.txt                                       ^L[Page 7]


Internet Draft          draft-pan-lsp-ping-02.txt           October 2001



Ping Pan
Juniper Networks
1194 N.Mathilda Ave
Sunnyvale, CA 94089
e-mail: pingpan@juniper.net
phone: 408.745.3704

Nischal Sheth
Juniper Networks
1194 N.Mathilda Ave
Sunnyvale, CA 94089
e-mail: nsheth@juniper.net
phone: 408.745.2068

Dave Cooper
Global Crossing
960 Hamlin Court
Sunnyvale, CA 94089
email: dcooper@gblx.net
phone: 916.415.0437

George Swallow
Cisco Systems, Inc.
250 Apollo Drive
Chelmsford, MA 01824
e-mail:  swallow@cisco.com
phone: 978.244.8143

Sanjay Wadhwa
Unisphere Networks, Inc.
10 Technology Park Drive
Westford, MA 01886-3146
email: swadhwa@unispherenetworks.com
phone: 978.589.0697

Ronald P. Bonica
WorldCom
22001 Loudoun County Pkwy
Ashburn, Virginia, 20147
email: ronald.p.bonica@wcom.com
phone: 703.886.1681









draft-pan-lsp-ping-02.txt                                       ^L[Page 8]


Html markup produced by rfcmarkup 1.129d, available from https://tools.ietf.org/tools/rfcmarkup/