[Docs] [txt|pdf|xml] [Tracker] [Email] [Diff1] [Diff2] [Nits]

Versions: (draft-pastor-i2nsf-vnsf-attestation) 00 01 02

Interface to Network Security Functions                        A. Pastor
Internet-Draft                                                  D. Lopez
Intended status: Experimental                             Telefonica I+D
Expires: September 14, 2017                                      A. Shaw
                                                    Hewlett Packard Labs
                                                          March 13, 2017

  Remote Attestation Procedures for Network Security Functions (NSFs)
                 through the I2NSF Security Controller


   This document describes the procedures a client can follow to assess
   the trust on an external NSF platform and its client-defined
   configuration through the I2NSF Security Controller.  The procedure
   to assess trustworthiness is based on a remote attestation of the
   platform and the NSFs running on it performed through a Trusted
   Platform Module (TPM) invoked by the Security Controller.

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on September 14, 2017.

Copyright Notice

   Copyright (c) 2017 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect

Pastor, et al.         Expires September 14, 2017               [Page 1]

Internet-Draft         Remote Attestation for NSFs            March 2017

   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
   2.  Requirements Language  . . . . . . . . . . . . . . . . . . . .  3
   3.  Establishing Client Trust  . . . . . . . . . . . . . . . . . .  4
     3.1.  First Step: Client-Agnostic Attestation  . . . . . . . . .  4
     3.2.  Second Step: Client-Specific Attestation . . . . . . . . .  5
     3.3.  Trusted Computing  . . . . . . . . . . . . . . . . . . . .  5
   4.  NSF Attestation Principles . . . . . . . . . . . . . . . . . .  7
     4.1.  Requirements for a Trusted NSF Platform  . . . . . . . . .  8
       4.1.1.  Trusted Boot . . . . . . . . . . . . . . . . . . . . .  8
       4.1.2.  Remote Attestation Service . . . . . . . . . . . . . .  9
       4.1.3.  Secure Boot  . . . . . . . . . . . . . . . . . . . . . 10
   5.  Remote Attestation Procedures  . . . . . . . . . . . . . . . . 11
     5.1.  Trusted Channel with the Security Controller . . . . . . . 12
     5.2.  Security Controller Attestation  . . . . . . . . . . . . . 13
     5.3.  Platform Attestation . . . . . . . . . . . . . . . . . . . 14
   6.  Security Considerations  . . . . . . . . . . . . . . . . . . . 14
   7.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 14
   8.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 15
     8.1.  Normative References . . . . . . . . . . . . . . . . . . . 15
     8.2.  Informative References . . . . . . . . . . . . . . . . . . 15
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 15

Pastor, et al.         Expires September 14, 2017               [Page 2]

Internet-Draft         Remote Attestation for NSFs            March 2017

1.  Introduction

   As described in [I-D.ietf-i2nsf-problem-and-use-cases], the use of
   externally provided NSF implies several additional concerns in
   security.  The most relevant threats associated with a externalized
   platform are detailed in [I-D.ietf-i2nsf-framework].  As stated
   there, mutual authentication between the user and the NSF environment
   and, more importantly, the attestation of the components in this
   environment by clients, could address these threats and provide an
   acceptable level of risk.  In particular:

   o  Client impersonation will be minimized by mutual authentication,
      and since appropriate records of such authentications will be made
      available, events are suitable for auditing (as a minimum) in the
      case of an incident.

   o  Attestation of the NSF environment, especially when performed
      periodically, will allow clients to detect the alteration of the
      processing components, or the installation of malformed
      components.  Mutual authentication will again provide an audit

   o  Attestation relying on independent Trusted Third Parties will
      alleviate the impact of malicious activity on the side of the
      provider by issuing the appropriate alarms in the event of any NSF
      environment manipulation.

   o  While it is true that any environment is vulnerable to malicious
      activity with full physical access (and this is obviously beyond
      the scope of this document), the application of attestation
      mechanisms raises the degree of physical control necessary to
      perform an untraceable malicious modification of the environment.

   The client can have a proof that their NSFs and policies are
   correctly (from the client point of view) enforced by the Security
   Controller.  Taking into account the threats identified in
   [I-D.ietf-i2nsf-framework], this document first identifies the user
   expectations regarding remote trust establishment, briefly analyzes
   Trusted Computing techniques, and finally describes the proposed
   mechanisms for remote establishment of trust through the Security

2.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   document are to be interpreted as described in [RFC2119].

Pastor, et al.         Expires September 14, 2017               [Page 3]

Internet-Draft         Remote Attestation for NSFs            March 2017

   In this document, these words will appear with that interpretation
   only when in ALL CAPS.  Lower case uses of these words are not to be
   interpreted as carrying RFC-2119 significance.

3.  Establishing Client Trust

   From a high-level standpoint, in any I2NSF platform, the client
   connects and authenticates to the Security Controller, which then
   initializes the procedures for authentication and authorization (and
   likely accounting and auditing) to track the loading and unloading of
   the client's NSFs, addressing the verification of the whole software
   stack: firmware, (host and guest) OSes, NSFs themselves and, in a
   virtualized environment, the virtualization system (hypervisors,
   container frameworks...).  Afterwards, user traffic from the client
   domain goes through the NSF platform that hosts the corresponding
   NSFs.  The user's expectations of the platform behavior are thus

   o  The user traffic will be treated according to the client-specified
      NSFs, and no other processing will be performed by the Security
      Controller or the platform itself (e.g. traffic eavesdropping).

   o  Each NSF (and its corresponding policies) behaves as configured by
      the client.

   We will refer to the attestation of these two expectations as the
   "client-agnostic attestation" and the "client-specific attestation".
   Trusted Computing techniques play a key role in addressing these

3.1.  First Step: Client-Agnostic Attestation

   This is the first interaction between a client and a Security
   Controller: the client wants to attest that he is connected to a
   genuine Security Controller before continuing with the
   authentication.  In this context, two properties characterize the
   genuineness of the Security Controller:

   1.  That the identity of the Security Controller is correct

   2.  That it will process the client credentials and set up the client
       NSFs and policies properly.

   Once these two properties are proven to the client, the client knows
   that their credentials will only be used by the Security Controller
   to set up the execution of their NSFs.

Pastor, et al.         Expires September 14, 2017               [Page 4]

Internet-Draft         Remote Attestation for NSFs            March 2017

3.2.  Second Step: Client-Specific Attestation

   From the security enforcement point of view, the client agnostic
   attestation focuses on the initialization of the execution platform
   for the NSFs.  This second step aims to prove to clients that their
   security is enforced accordingly with their choices (i.e.  NSFs and
   policies).  The attestation can be performed at the initialization of
   the NSFs, before any user traffic is processed by the NSFs, and
   optionally during the execution of the NSFs.

   Support of static attestation, performed at initialization time, for
   the execution platform and the NSFs is REQUIRED for a Security
   Controller managing NSFs, and MUST be performed before any user
   traffic is redirected through any set of NSFs.  The Security
   Controller MUST provide proof to the client that the instantiated
   NSFs and policies are the ones chosen.

   Additionally to the NSFs instantiation attestation, a continuous
   attestation of the Security Controller and the NSF execution MAY be
   required by a client to ensure their security.  The sampling periods
   for the continuous attestation of NSFs an Controller MAY be

3.3.  Trusted Computing

   In a nutshell, Trusted Computing (TC) aims at answering the following
   question: "As a user or administrator, how can I have some assurance
   that a computing system is behaving as it should?".  The major
   enterprise level TC initiative is the Trusted Computing Group [TCG],
   which has been established for more than a decade, that primarily
   focuses on developing TC for commodity computers (servers, desktops,
   laptops, etc.).

   The overall scheme proposed by TCG for using Trusted Computing is
   based on a step-by-step extension of trust, called a Chain of Trust.
   It uses a transitive mechanism: if a user can trust the first
   execution step and each step correctly attests the next executable
   software for trustworthiness, then a user can trust the system.

Pastor, et al.         Expires September 14, 2017               [Page 5]

Internet-Draft         Remote Attestation for NSFs            March 2017

                |           |    extends PCR
                | Platform  +------------------------+
                |           |                        |
                +-----^-----+                        |
                      |                              |
                      |measures                      |
                +-----------+                        |
                | Security  |    extends PCR         |
                |           +---------------------+  |
                | Controller|                     |  |
                +-----^-----+                     |  |
                      |                           |  |
                      |measures                 +-v--v----------+
                +-----------+                   |               |
                |           |    extends PCR    |               |
                | Bootloader+-------------------> Root of Trust |
                |           |                   |               |
                +-----^-----+                   |               |
                      |                         +-^--^----------+
                      |measures                   |  |
                +-----------+                     |  |
                |           |    extends PCR      |  |
                | BIOS      +---------------------+  |
                |           |                        |
                +-----^-----+                        |
                      |                              |
                      |measures                      |
                +-----------+                        |
                | Bootblock |    extends PCR         |
                |  (CRTM)   +------------------------+
                |           |

                   Figure 1: Applying Trusted Computing

   Effectively, during the loading of each piece of software, the
   integrity of each piece of software is measured and stored inside a
   log that reflects the different boot stages, as illustrated in the
   figure above.  Later, at the request of a user, the platform can
   present this log (signed with the unique identity of the platform),
   which can be checked to prove the platform identity and attest the
   state of the system.  The base element for the extension of the Chain
   of Trust is called the Core Root of Trust.

   The TCG has created a standard for the design and usage of a secure
   crypto-processor to address the storage of keys, general secrets,

Pastor, et al.         Expires September 14, 2017               [Page 6]

Internet-Draft         Remote Attestation for NSFs            March 2017

   identities, and platform integrity measurements: the Trusted Platform
   Module (TPM).  When using a TPM as a root of trust, measurements of
   the software stack are stored in special on-board Platform
   Configuration Registers (PCRs) on a discrete TPM.  There are normally
   a small number of PCRs that can be used for storing measurements;
   however, it is not possible to directly write to a PCR.  Instead,
   measurements must be stored using a process called Extending PCRs.

   The extend operation can update a PCR by producing a global hash of
   the concatenated values of the previous PCR value with the new
   measurement value.  The Extend operation allows for an unlimited
   number of measurements to be captured in a single PCR, since the size
   of the value is always the same and it retains a verifiable ordered
   chain of all the previous measurements.

   Attestation of the virtualization platform will thus rely on a
   process of measuring the booted software and storing a chained log of
   measurements, typically referred to as Trusted Boot.  The user will
   either validate the signed set of measurements with a trusted third
   party verifier who will assess whether the software configuration is
   trusted, or the user can check for themselves against their own set
   of reference digest values (measurements) that they have obtained a
   priori, and having already known the public endorsement key of the
   remote Root of Trust.

   Trusted Boot should not be confused with a different mechanism known
   as "Secure Boot", as they both are designed to solve different
   problems.  Secure Boot is a mechanism for a platform owner to lock a
   platform to only execute particular software.  Software components
   that do not match the configuration digests will not be loaded or
   executed.  This mechanism is particularly useful in preventing
   malicious software that attempts to install itself in the boot record
   (a bootkit) from successfully infecting a platform on reboot.  A
   common standard for implementing Secure Boot is described in [UEFI].
   Secure Boot only enforces a particular configuration of software, it
   does not allow a user to attest or quote for a series of

4.  NSF Attestation Principles

   Following the general requirements described in
   [I-D.ietf-i2nsf-framework] the Security Controller will become the
   essential element to implement the measurements described above,
   relying on a TPM for the Root of Trust.

   A mutual authentication of clients and the Security Controller MUST
   be performed, establishing the desired level of assurance.  This

Pastor, et al.         Expires September 14, 2017               [Page 7]

Internet-Draft         Remote Attestation for NSFs            March 2017

   level of assurance will determine how stringent are the requirements
   for authentication (in both directions), and how detailed the
   collected measurements and their verification will be.  Furthermore,
   the NSF platform MUST run a TPM, able to collect measurements of the
   platform itself, the Security Controller, and the NSFs being
   executed.  The Security Controller MUST make the attestation
   measurements available to the client, directly or by means of a
   Trusted Third Party.

   As described in [I-D.ietf-i2nsf-framework], a trusted connection
   between the client and the Security Controller MUST be established
   and all traffic to and from the NSF environment MUST flow through
   this connection

   NOTE: The reference to results from WGs such as NEA and SACM is
   currently under consideration and will be included here.

4.1.  Requirements for a Trusted NSF Platform

   Although a discrete hardware TPM is RECOMMENDED, relaxed alternatives
   (such as embedded CPU TPMs, or memory and execution isolation
   mechanisms) MAY also be applied when the required level of assurance
   is lower.  This reduced level of assurance MUST be communicated to
   the client by the Security Controller during the initial mutual
   authentication phase.  The Security Controller MUST use a set of
   capabilities to negotiate the level of assurance with the client.

4.1.1.  Trusted Boot

   NOTE: This section is derived from the original version of the
   document, focused on virtual NSFs.  Although it seems to be
   applicable to any modern physical appliance, we must be sure all
   these considerations are 100% applicable to physical NSFs as well,
   and provide exceptions when that is not the case.  Support from an
   expert in physical node attestation is required here.

   All clients who interact with a Security Controller MUST be able to:

   a.  Identify the Security Controller based on the public key of a
       Root of Trust.

   b.  Retrieve a set of measurements of all the base software the
       Security Controller has booted (i.e. the NSF platform).

   This requires that firmware and software MUST be measured before
   loading, with the resulting value being used to extend the
   appropriate PCR register.  The general usage of PCRs by each software
   component SHOULD conform to open standards, in order to make

Pastor, et al.         Expires September 14, 2017               [Page 8]

Internet-Draft         Remote Attestation for NSFs            March 2017

   verifying attestation reports interoperable, as it is the case of TCG
   Generic Server Specification [TCGGSS].

   The following list describes which PCR registers SHOULD be used
   during a Trusted Boot process:

   o  PCRs 00-03: for use by the CRTM (Initial EEPROM or PC BIOS)

   o  PCRs 04-07: for use by the bootloader stages

   o  PCRs 08-15: for use by the booted base system

   A signed audit log of boot measurements should also be provided.  The
   PCR values can also be used as an identity for dynamically decrypting
   encrypted blobs on the platform (such as encryption keys or
   configurations that belong to operating system components).  Software
   can choose to submit pieces of data to be encrypted by the Root of
   Trust (which has its own private asymmetric key and PCR registers)
   and only have it decrypted based on some criteria.  These criteria
   can be that the platform booted into a particular state (e.g. a set
   of PCR values).  Once the desired criteria are described and the
   sensitive data is encrypted by the root of trust, the data has been
   sealed to that platform state.  The sealed data will only be
   decrypted when the platform measurements held in the root of trust
   match the particular state.

   Trusted Boot requires the use of a root of trust for safely storing
   measurements and secrets.  Since the Root of Trust is self-contained
   and isolated from all the software that is measured, it is able to
   produce a signed set of platform measurements to a local or remote
   user.  However, Trusted Boot does not provide enforcement of a
   configuration, since the root of trust is a passive component not in
   the execution path, and is solely used for safe independent storage
   of secrets and platform measurements.  It will respond to attestation
   requests with the exact measurements that were made during the
   software boot process.  Sealing and unsealing of sensitive data is
   also a strong advantage of Trusted Boot, since it prevents leakage of
   secrets in the event of an untrusted software configuration.

4.1.2.  Remote Attestation Service

   A service MUST be present for providing signed attestation report
   (e.g. the measurements) from the Root of Trust (RoT) to the client.
   In case of failure to communicate with the service, the client MUST
   assume the service cannot be trusted and seek an alternative Security

   Since some forms of RoT require serialised access (i.e. due to slow

Pastor, et al.         Expires September 14, 2017               [Page 9]

Internet-Draft         Remote Attestation for NSFs            March 2017

   access to hardware), latency of getting an attestation report could
   increase with simultaneous requests.  Simultaneous requests could
   occur if multiple Trusted Third Parties (TTP) request attestation
   reports at the same time.  This MAY be improved through batching of
   requests, in a special manner.  In a typical remote attestation
   protocol, the client sends a random number ("nonce") to the RoT in
   order to detect any replay attacks.  Therefore, caching of an
   attestation report does not work, since there is the possibility that
   it may not be a fresh report.  The solution is to batch the nonce for
   each requestor until the RoT is ready for creating the attestation
   report.  The report will be signed by the embedded identity of the
   RoT to provide data integrity and authenticity, and the report will
   include all the nonces of the requestors.  Regardless of the number
   of the number of nonces included, the requestor verifying the
   attestation report MUST check to see if the requestor's nonce was
   included in order to detect replay attacks.  In addition to the
   attestation report containing PCRs, an additional report known as an
   SML (Secure Measurement Log) can be returned to the requestor to
   provide more information on how to verify the report (e.g. how to
   reproduce the PCR values).  The integrity of the SML is protected by
   a PCR measurement in the RoT.  An example of an open standard for
   responses is [TCGIRSS].  Further details are discussed in
   Section 5.2.

   As part of initial contact, the Security Controller MAY present a
   list of external TTPs that the client can use to verify it.  However,
   the client MUST assess whether these external verifiers can be
   trusted.  The client can also choose to ignore or discard the
   presented verifiers.

   Finally, to prevent malicious relaying of attestation reports from a
   different host, the authentication material of the secure channel
   (e.g.  TLS, IPSec, etc.)  SHOULD be bound to the RoT and verified by
   the connected client, unless the lowest levels of assurance have been
   chosen and an explicit warning issued.  This is also addressed in
   Section 5.1.

4.1.3.  Secure Boot

   Using a mechanism such as Secure Boot helps provide strong prevention
   of software attacks.  Furthermore, in combination with a hardware-
   based TPM, Secure Boot can provide some resilience to physical
   attacks (e.g. preventing a class of offline attacks and unauthorized
   system replacement).  For NSF providers, it is RECOMMENDED that
   Secure Boot is employed wherever possible with an appropriate
   firmware update mechanism, due to the possible threat of software/
   firmware modifications in either public places or privately with
   inside attackers.

Pastor, et al.         Expires September 14, 2017              [Page 10]

Internet-Draft         Remote Attestation for NSFs            March 2017

5.  Remote Attestation Procedures

   The establishment of trust with the Security Controller and the NSF
   platform consists of three main phases, which need to be coordinated
   by the client:

   1.  Trusted channel with the Security Controller.  During this phase,
       the client securely connects to the Security Controller to avoid
       that any data can be tampered with or modified by an attacker if
       the network cannot be considered trusted.  The establishment of
       the trusted channel is completed after the next step.

   2.  Security Controller attestation.  During this phase, the client
       verifies that the Security Controller components responsible for
       handling the credentials and for the isolation with respect to
       other potential clients are behaving correctly.  Furthermore, it
       is verified that the identity of the platform attested is the
       same of the one presented by the Security Controller during the
       establishment of the secure connection.

   3.  Platform attestation.  During this step, which can be repeated
       periodically until the connection is terminated, the Security
       Controller verifies the integrity of the elements composing the
       NSF platform.  The components responsible for this task have been
       already attested during the previous phase.

                 3. Attestation    | Trusted  |   3. Attestation
              +-------------------->  Third   <----------+
              |                    |  Party   |          |
              |                    +----------+ +--------+-------+
   +----------v-------+                         |  +-----v-----+ |
   |      Client      |                         |  | Security  | |
   |                  |  1. Trusted channel     |  | Controller| |
   | 2. Get Cert      +------+ handshake +--------->           | |
   | 3. Attestation   |                         |  +-----------+ |
   | 4. Cont.handshake|                         |                |
   |                  |                         |                |
   |                  |                         |  +---------+   |
   |                  |                         |  |   NSF   |   |
   |                  |                         |  +---------+   |
   +------------------+                         +----------------+

                  Figure 2: Steps for remote attestation

Pastor, et al.         Expires September 14, 2017              [Page 11]

Internet-Draft         Remote Attestation for NSFs            March 2017

   In the following each step, as depicted in the above figure, is
   discussed in more detail.

5.1.  Trusted Channel with the Security Controller

   A trusted channel is an enhanced version of the secured channel that.
   It adds the requirement of integrity verification of the contacted
   endpoint by the other peer during the initial handshake to the
   functionality of the secured channel.  However, simply transmitting
   the integrity measurements over the channel does not guarantee that
   the platform verified is the channel endpoint.  The public key or the
   certificate for the secure communication MUST be included as part of
   the measurements presented by the contacted endpoint during the
   remote attestation.  This way, a malicious platform cannot relay the
   attestation to another platform as its certificate will not be
   present in the measurements list of the genuine platform.

   In addition, the problem of a potential loss of control of the
   private key must be addressed (a malicious endpoint could prove the
   identity of the genuine endpoint).  This is done by defining a long-
   lived Platform Property Certificate.  Since this certificate connects
   the platform identity to the AIK public key, an attacker cannot use a
   stolen private key without revealing his identity, as it may use the
   certificate of the genuine endpoint but cannot create a quote with
   the AIK of the other platform.

   Finally, since the platform identity can be verified from the
   Platform Property Certificate, the information in the certificate to
   be presented during the establishment of a secure communication is
   redundant.  This allows for the use of self-signed certificates.
   This would simplify operational procedures in many environments,
   especially when they are multi-tenant.  Thus, in place of
   certificates signed by trusted CAs, the use of self-signed
   certificates (which still need to be included in the measurements
   list) is RECOMMENDED.

   The steps required for the establishment of a trusted channel with
   the Security Controller are as follows:

   1.  The client begins the trusted channel handshake with the selected
       Security Controller.

   2.  The certificate of the Security Controller is collected and used
       for verifying the binding of the attestation result to the
       contacted endpoint.

   3.  The client performs the remote attestation protocol with the
       Security Controller, either directly or with the help of a

Pastor, et al.         Expires September 14, 2017              [Page 12]

Internet-Draft         Remote Attestation for NSFs            March 2017

       Trusted Third Party.  The Trusted Third Party MAY perform the
       verification of attestation quotes on behalf of multiple clients.

   4.  If the result of the attestation is positive, the application
       continues the handshake and establishes the trusted channel.
       Otherwise, it closes the connection.

5.2.  Security Controller Attestation

   During the establishment of the trusted channel, the client attests
   the Security Controller by verifying the identity of the contacted
   endpoint and its integrity.  Initially the Security Controller
   measures all of the hardware and software components involved in the
   boot process of the NSF platform, in order to build the chain of

   Since a client may not have enough functionality to perform the
   integrity verification of a Security Controller, the client MAY
   request the status of a Security Controller to be computed by a
   Trusted Third Party (TTP).  This choice has the additional advantage
   of preventing an attacker from easily determining the software
   running at the Security Controller.

   If the client directly performs the remote attestation, it executes
   the following steps:

   1.  Ask the Security Controller to generate an integrity report with
       the format defined in [TCGIRSS].

   2.  The Security Controller retrieves the measurements and asks the
       TPM to sign the PCRs with an Attestation Identity Key (AIK).
       This signature provides the client with the evidence that the
       measurements received belong to the Security Controller being

   3.  Once the integrity report has been generated it is sent back to
       the client.

   4.  The client first checks if the integrity report is valid by
       verifying the quote and the certificate associated to the AIK,
       and then determines if the Security Controller is behaving as
       expected (i.e. its software has not been compromised and
       isolation among the clients connected to it is enforced).  As
       part of the verification, the client also checks that the digest
       of the certificate, received during the trusted channel
       handshake, is present among measurements.

   If the client has limited computation resources, it may contact a TTP

Pastor, et al.         Expires September 14, 2017              [Page 13]

Internet-Draft         Remote Attestation for NSFs            March 2017

   which, in turn, attests the Security Controller and returns the
   result of the integrity evaluation to the client, following the same
   steps depicted above.

5.3.  Platform Attestation

   The main outcome of the Security Controller attestation is to detect
   whether or not it is correctly configuring the operational
   environment for NSFs to be managed by the connecting client (the NSF
   platform, or just platform) in a way that any user traffic is
   processed only by these NSFs that are part of the platform.  Platform
   attestation, instead, evaluates the integrity of the NSFs running on
   the platform.

   Platform attestation does not imply a validation of the mechanisms
   the Security Controller can apply to select the appropriate NSFs to
   enforce the Service Policies applicable to specific flows.  The
   selection of these NSFs is supposed to happen independent of the
   attestation procedures, and trust on the selection process and the
   translation of policies into function capabilities has to be based on
   the trust clients have on the Security Controller being attested as
   the one that was intended to be used.  An attestation of the
   selection and policy mapping procedures constitute an interesting
   research problem, but it is out of the scope of this document.

   The procedures are essentially similar to the ones described in the
   previous section.  This step MAY be applied periodically if the level
   of assurance selected by the user requires it.

   Attesting NSFs, especially if they are running as virtual machines,
   can become a costly operation, especially if periodic monitoring is
   required by the requested level of assurance.  There are several
   proposals to make this feasible, from the proposal of virtual TPMs in
   [VTPM] to the application of Virtual Machine Introspection through an
   integrity monitor described by [VMIA].

6.  Security Considerations

   This document is specifically oriented to security and it is
   considered along the whole text.

7.  IANA Considerations

   This document requires no IANA actions.

Pastor, et al.         Expires September 14, 2017              [Page 14]

Internet-Draft         Remote Attestation for NSFs            March 2017

8.  References

8.1.  Normative References

              Lopez, D., Lopez, E., Dunbar, L., Strassner, J., and R.
              Kumar, "Framework for Interface to Network Security
              Functions", draft-ietf-i2nsf-framework-04 (work in
              progress), October 2016.

              Hares, S., Lopez, D., Zarny, M., Jacquenet, C., Kumar, R.,
              and J. Jeong, "I2NSF Problem Statement and Use cases",
              draft-ietf-i2nsf-problem-and-use-cases-11 (work in
              progress), March 2017.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/
              RFC2119, March 1997,

   [TCG]      "Trusted Computing Group (TCG)",

   [TCGGSS]   "TCG Generic Server Specification, Version 1.0",

   [TCGIRSS]  "Infrastructure Work Group Integrity Report Schema
              Specification, Version 1.0",

8.2.  Informative References

   [UEFI]     "UEFI Specification Version 2.2 (Errata D), Tech. Rep.".

   [VMIA]     Schiffman, J., Vijayakumar, H., and T. Jaeger, "Verifying
              System Integrity by Proxy",

   [VTPM]     "vTPM:Virtualizing the Trusted Platform Module", <https://

Pastor, et al.         Expires September 14, 2017              [Page 15]

Internet-Draft         Remote Attestation for NSFs            March 2017

Authors' Addresses

   Antonio Pastor
   Telefonica I+D
   Zurbaran, 12
   Madrid,   28010

   Phone: +34 913 128 778
   Email: antonio.pastorperales@telefonica.com

   Diego R. Lopez
   Telefonica I+D
   Editor Jose Manuel Lara, 9 (1-B)
   Seville,   41013

   Phone: +34 913 129 041
   Email: diego.r.lopez@telefonica.com

   Adrian L. Shaw
   Hewlett Packard Labs
   Long Down Avenue
   Bristol,   BS34 8QZ

   Phone: +44 117 316 2877
   Email: als@hpe.com

Pastor, et al.         Expires September 14, 2017              [Page 16]

Html markup produced by rfcmarkup 1.123, available from https://tools.ietf.org/tools/rfcmarkup/