[Docs] [txt|pdf] [Tracker] [Email] [Diff1] [Diff2] [Nits]

Versions: 00 01

Network Working Group                             Albert J. Tian
Internet Draft                                    Redback Networks
Expiration Date: Jan 2005                         George Apostolopoulos
                                                  July 2004

             Source Routed MPLS LSP using Domain Wide Label


1. Status of this Memo

   By submitting this Internet-Draft, I certify that any applicable
   patent or other IPR claims of which I am aware have been disclosed,
   or will be disclosed, and any of which I become aware will be
   disclosed, in accordance with RFC 3668.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as ``work in progress.''

   The list of current Internet-Drafts can be accessed at

   The list of Internet-Draft Shadow Directories can be accessed at

2. Abstract

   One advantage that MPLS provides is that it allows traffic to be
   directed through an explicit path that deviates from IP routing.
   Such ability is widely used in traffic-engineering and fast-reroute.
   Currently signaling protocols such as RSVP is needed to establish and
   maintain such an explicit Label Switched Path. When there are a large
   number of such signaled LSPs in the network, the aggregated signaling
   and maintenance overhead can be significant.

   In this paper, we propose a way to establish a source routed explicit
   path with zero signaling overhead. The scheme uses a stack of labels

Tian & Apostolopoulos                                           [Page 1]

Internet Draft   draft-tian-mpls-lsp-source-route-01.txt       July 2004

   and requires domain wide LDP FEC to label bindings.

3. Introduction

   On merging capable LSRs, LDP builds merging LSP trees rooted at the
   egress of the FEC. LDP allocated labels usually are only of local
   significance.  In other words, an FEC can bind to different labels on
   different links in a network. By doing so, each LSR can achieve
   conflict free label allocation without any coordination.

   But in some cases, a domain wide FEC to label binding may be
   desirable. In a domain wide FEC to label binding, a given label is
   always bound to the same FEC on all links in the network, if a
   binding for the given label exists. We call such a label a Domain
   Wide Label(DWL).

   Consider the following example where FEC-d corresponds to a loopback
   interface address d on LSR-D. In traditional FEC to label binding,
   FEC-d can bind to different labels on different links:

              label 30  label 20  label 10
    FEC-d : A ------- B ------- C ------- D

   In domain wide label binding, FEC-D binds to the same label 10 on all

              label 10  label 10  label 10
    FEC-d : A ------- B ------- C ------- D

4. Terminologies

   Domain Wide Label (DWL): A label is said to be a Domain Wide Label if
   the FECs that map to that label are always the same on all links in a
   MPLS domain.

   Local Label: A label is said to be a local label if multiple
   distinctive FECs can map to that label on different links in a MPLS

Tian & Apostolopoulos                                           [Page 2]

Internet Draft   draft-tian-mpls-lsp-source-route-01.txt       July 2004

5. Source Routed LSP

   DWL allows an efficient way to support source routing in an LDP
   enabled network using a stack of labels.

5.1. An example

   For example, in the following network there are 6 LSRs A through F.
   Each LSR has a loopback interface with a domain wide label allocated
   for it. Assuming LDP is running on all the LSRs and LDP can be
   enhanced to distribute such domain wide label bindings throughout the
   MPLS domain. The domain wide labels still have the same semantics as
   other LDP labels, just that the same label here always maps to the
   same FEC on all LSRs in the MPLS domain. Later in this document, we
   will give out the details on the LDP enhancements.

            +-------> 60/30/P ---> 30/P -------->+
            ^                                    |
            |      D-----------E-----------F     |
            |      | 40        50       60 |     v
       50/60/30/P  |                       |     P
                   | 10        20       30 |

                             Fig. 1

   The domain wide label allocation on all LSRs are as follows:

    LSR Label Loopback-Interface-prefix/FEC
    A   10    a
    B   20    b
    C   30    c
    D   40    d
    E   50    e
    F   60    f

   In this example, all LSRs would use label 10 to deliver packets to
   address a on LSR A, and use label 30 to deliver packets to address c
   on LSR C, and so on and so forth.

   Lets say that normally LSR A would use label 30 to deliver packets to
   C along path A-B-C. So FEC c to label 30 mapping must be installed on
   all LSRs on the path. Here we assume this can be achieved by the
   enhanced LDP.

   Now if LSR A wants to use an alternative path A-D-E-F-C to deliver
   packets to C, it can push an additional label stack 40/50/60/30 on to

Tian & Apostolopoulos                                           [Page 3]

Internet Draft   draft-tian-mpls-lsp-source-route-01.txt       July 2004

   the packet and forward the packet according to label FIB. Here 40 is
   the top (outer most) label. If PHP is enabled, the top label 40 will
   be popped on LSR A and the packet will be forwarded to LSR D
   according to the action associated with label 40. When the packet
   arrives on LSR D, the top label 50 will determine the nexthop to be
   LSR E with action pop. Similar procedures will happen on LSR E and F,
   eventually deliver the payload P to LSR C.

   If PHP is disabled on these LSRs, the labels will not be popped at
   the penultimate hop resulting in one extra label on the label stack
   in the packet.

   Similarly, LSR A can use stack 50/30 to specify a Loosely Source
   Routed Path A-E-C. In this case top label will deliver the packet to
   LSR E, and the next label 30 will deliver the packet to LSR C.

5.2. Benefits of Source Routed LSP

   There are several advantages of such source routed LSPs.

5.2.1. Zero signaling and maintenance overhead

   Since these LSPs are source routed, there is no signaling overhead
   and no maintenance overhead. Also only the headend of the LSP needs
   to maintain the state related to the LSP, other LSRs on the LSP are
   not even aware of the existence of such LSPs.

   This makes source routed LSPs perfect for establishing bypass LSPs
   for fast-reroute. In such applications, numerous bypass LSPs need to
   be created and maintained yet only to be used very infrequently when
   some link or node fails in a network.

5.2.2. Zero signaling delay

   Also because the LSPs are source routed, they can be used immediately
   after the stack of labels are determined. This allows LSPs to be
   adjusted on the fly without any interruption. In other words, make-
   before-break is inherit in the design.

Tian & Apostolopoulos                                           [Page 4]

Internet Draft   draft-tian-mpls-lsp-source-route-01.txt       July 2004

5.3. Other Benefits of DWL

5.3.1. DWL and LDP node protection

   In applications such as LDP node protection as described in [SHEN00],
   an LSR needs to learn labels allocated by the next-nexthop LSR for a
   given FEC. Without DWL, protocol extensions as outlined in [SHEN00]
   will be needed to propagate that information. In a DWL enabled LDP
   network, the protocol extensions described in [SHEN00] will not be
   needed since the next-nexthop label for a FEC will be the same as the
   label allocated on the local box if that label is a DWL.

5.3.2. DWL can help in troubleshooting

   DWL makes the network easier to troubleshoot. Since each FECs using
   DWL bind to the same label on all the hops, packets with such a label
   can be correlated to the FEC easily.

6. Strictly Source Routed Segments over High Cost Links

   Using a stack of DWLs, one can construct a Loosely Source Routed
   Path(LSRP), with each DWL representing a loose segment on the path.

   In most LDP enabled networks, at direct link between two LSRs is the
   shortest path between the two according to routing. In such a
   network, a DWL for a directly connected neighbor will deliver packets
   over one or more of the directly connect links to that neighbor. In
   this case, strict segments in an explicit path can be implemented
   using DWLs.

   However, in some cases if all direct links between two adjacent LSRs
   have been configured with higher link costs than the shortest
   indirect paths, then these direct links will not be used by IP
   routing except for packets whose destination address is the interface
   address on the far end of the high cost link.

       |                           |
       |                           |
       |                           | loopback label 100
       X-------------3-------------Y interface address label 10

                 Fig. 2

Tian & Apostolopoulos                                           [Page 5]

Internet Draft   draft-tian-mpls-lsp-source-route-01.txt       July 2004

   In the example given in Fig. 2, the costs of the links among three
   LSRs X, Y and Z are marked on the links. Label 100 is a DWL for FEC whose egress is a loopback interface address on LSR Y.
   Even when there is a direct link between X and Y, MPLS packets
   arriving on X with top label 100 will still be forwarded to LSR Z,
   since the path X-Z-Y has a better metric. The only traffic that will
   be sent over the direct link between X and Y is traffic from X with
   destination, and vise versa, due to the fact that most of
   the implementations prefer directly connected interface route over
   any other route types.

   In order to guarantee a Strictly Source Routed Segment between X and
   Y in this scenario, a new Longest Match Address FEC element (LM-
   Address FEC element) is introduced that uses longest prefix match
   instead of exact match to find its matching route. The LM-Address FEC
   element is defined in as follows:

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     | LM-Address(4) |     Address Family            | Host Addr Len |
     |                                                               |
     |                     Host Addr                                 |
     |                                                               |

     Address Family
        Two octet quantity containing a value from ADDRESS FAMILY
        NUMBERS in [RFC1700] that encodes the address family for the
        address prefix in the Prefix field.

     Host Addr Len
        Length of the Host address in octets.

     Host Addr
        An address encoded according to the Address Family field.

   The LM-Address FEC element is essentially the same as the Host
   Address FEC element, except that it has a different FEC element type

   To solve the strict hop over high cost link problem, a DWL needs to
   be allocated on Y and bound to LM-Address FEC element  When
   the binding is advertised to X, X performs a longest prefix match in
   its routing table and finds the route A LSP will be
   created with link X-Y as the outgoing interface.

Tian & Apostolopoulos                                           [Page 6]

Internet Draft   draft-tian-mpls-lsp-source-route-01.txt       July 2004

   To specify a strict hop over a high cost link in an explicit path,
   the interface address needs to be used.

7. LDP extensions for DWL

7.1. Reserve a pool of labels for DWL

   A pool of labels need to be set aside on all LSRs in the domain to be
   used as DWLs. Local labels MUST not be allocated from this pool,
   otherwise we can not guarantee that the same label always maps to the
   same FEC. After the pool of labels are reserved, LSRs can then
   allocate domain wide labels from the pool.

   Implementations MUST allow user to configure the DWL label range.
   All LSRs in a domain MUST agree on the range of labels reserved for
   DWL to avoid allocating local labels from the DWL pool.

   Since most existing implementations allocate local labels from near
   the lower end of the label space, label ranges near the higher end of
   the label space is usually more suitable for DWLs.

7.2. Allocating DWL

   In most cases, each LSR is allocated a unique DWL from the DWL pool
   for its loopback interface address FEC. This FEC to DWL binding will
   be propagated throughout the MPLS domain using LDP.

   This allocation can be achieved in several ways:
     a) manually allocate via configuration, or
     b) automatically allocate through a centralized server, or
     c) algorithmically derived from something else.

   Method a) is the most strait forward. In this case the operator needs
   to make sure there are no conflicts in DWL allocations.  Since each
   LSR only needs one or in some cases two DWLs, this should not be a
   big burden for operators.

7.3. Advertising and Detecting DWL

   An LSR can determine if a label is a DWL by checking if it falls
   within the DWL range. Hence DWL can be advertised using the existing
   Generic Label TLV.

Tian & Apostolopoulos                                           [Page 7]

Internet Draft   draft-tian-mpls-lsp-source-route-01.txt       July 2004

7.4. Extensions to Label Mapping Procedures

   When a LABEL MAPPING message is received with a DWL in the label TLV,
   the receiving LSR SHOULD try to allocate the same label for the FEC.
   If the received DWL is already allocated to a different FEC, a local
   label SHOULD be allocated for the FEC, and a NOTIFICATION message
   with non-fatal status code SHOULD be sent to the advertising router.

   The value of the status code is TBD.

7.5. PHP

   Since DWL label values need to be communicated to adjacent LSRs so
   that they can be further propagated upstream, implicit-null label can
   not be used to signal PHP operation. One solution is to infer PHP
   from ADDRESS messages.

   For FEC with /32 Prefix FEC elements, or Host Address FEC elements,
   or LM-Address FEC elements, if all the addresses in the FEC are among
   the addresses in the ADDRESS messages from the advertising LSR, and
   the advertising LSR is not a targeted neighbor, then PHP is assumed
   for the LSP unless otherwise instructed by local policy.

8. Construct Source Routed LSP using DWL

   Assuming an explicitly routed path is specified by a list of IP
   prefixes, each of which represents either a loose hop or a strict
   hop.  Given such a path, we can construct a Source Routed LSP using
   the following algorithm:

    a) Set the current node to be the last node in the path, and set the
       label stack to be empty.

    b) For the IP prefix of the current node, find an FEC element that
       exactly matches the IP prefix. Host Address FEC elements and
       LM-Address FEC elements are considered of having prefix length
       32. Then find the DWL that is bound to that FEC element. Push
       the DWL onto the stack.

       If such DWL can not be found, abort the algorithm with an error.

    c) If the current node is the first node in the path, terminate the
       Otherwise set the current node to its predecessor in the path
       and goto step a).

Tian & Apostolopoulos                                           [Page 8]

Internet Draft   draft-tian-mpls-lsp-source-route-01.txt       July 2004

   The resulting label stack represents a source routed LSP, and can be
   used to forward packets from the starting point to the last hop
   following the desired path.

9. Other Considerations

9.1. Interface Label Space

   A LSR support interface label space needs to reserve the same DWL
   label range on all interfaces, and needs to allocate the same label
   for an FEC out of the reserved DWL label range.

9.2. ATM and Frame Lable Encoding

   For a network using ATM label TLV or Frame Relay Label TLV, a
   seperate DWL label range must be defined for each different label
   encodings. Still DWLs can be advertised using the same ATM Label TLV
   or the Frame Relay Label TLV.

9.3. Verification of Source Routed Paths

   Standard tools such as MPLS ping and MPLS traceroute can be used to
   verify a source routed path is functioning as expected.

9.4. Compatibility Considerations

   The solution proposed in this document is compatible with existing
   LDP specification. LSRs that do not understand DWL will not get the
   benefit of DWL, but basic LDP connectivity should remain intact.

9.5. Loop Prevention

   One very nice attribute of the source routed LSP is that as long as
   each hop is loop free, the path will also be loop free.

   It is possible to construct a LSP that visits the same LSR twice by
   including the same DWL twice in the stack, but no infinite loop will
   be created.

   It is recommended for LSRs that support DWL to copy TTL values from
   the outer label to inner label when a label is popped, to avoid
   delayed TTL expiration.

Tian & Apostolopoulos                                           [Page 9]

Internet Draft   draft-tian-mpls-lsp-source-route-01.txt       July 2004

10. Security Considerations

   This document proposed a new and efficient way to implement source
   routing. All known security concerns related to source routing may
   also be concerns here.

   Please note that an attacker can use a stack of labels to perform
   source routing today if label bindings are known on all routers on
   the path. With this proposal, if label bindings on one router is
   known to the attacker, then source routing can be utilized by the

   The main security concerns related to source routing include the
   following scenarios where source routing may be abused:

    - to bypass administrative control
    - to make a malicious packet appear as if it had come from a trusted
    - to reach otherwise unreachable part of the network such as
      private address space
    - to collect information about a network

   The concerns can be eliminated by not accepting DWLs from outside the
   trusted domain. This can be achieved by doing the following:

    1) Do not accept labeled packets from outside the trusted domain.

       If labeled packets must be accepted from outside, then do not
       accept DWLs from outside the trusted domain. Since the DWL range
       is known, this policy can be achieved by label based filtering
       at the entrance points of the trusted domain to block packets
       with any DWLs in the label stack.

    2) Do not accept labeled packets arriving from tunnels (such as GRE
       or IP-in-IP, etc). This can be achieved by disabling protocol ID
       MPLS at tunnel next protocol ID demux point.

       If MPLS over tunnel must be supported, then do not accept
       labeled packets from tunnels originated from outside the trusted

       If labeled packet must be accepted from tunnels originated from
       outside the trusted domain, then do not accept labeled packets
       with DWLs from these tunnels.

   One difference between MPLS source route and IP source route option
   is that the IP source route option is designed to specify the path
   for both the request in the forwarding direction and the response in

Tian & Apostolopoulos                                          [Page 10]

Internet Draft   draft-tian-mpls-lsp-source-route-01.txt       July 2004

   the reverse direction, while MPLS source route can only specify the
   path in the forward direction. Therefore the security risk for MPLS
   source route is lower than the IP source route option.

11. IANA Considerations

   A new LM-Address FEC element TLV is defined in this document with FEC
   element type 0x04. This LDP extension requires this FEC element type
   to be allocated by IANA.

   A new status code for LDP NOTIFICATION message to notify the
   conflicts in DWLs needs to be defined and allcoated by IANA.

12. Acknowledgments

   The authors would like to thank Naiming Shen, Enke Chen and Acee
   Lindem for their comments.

13. References

    [RFC3036] L. Andersson, P. Doolan, N. Feldman, A. Fredette, and B.
    Thomas, "LDP Specification", RFC 3036, January 2001.

    [SHEN00]  N. Shen, E. Chen, A. Tian, "Discovering LDP Next-Nexthop
    Labels", draft-shen-mpls-ldp-nnhop-label-01.txt, work in progress.

    [SHEN01]  N. Shen and P. Pan, "Nexthop Fast ReRoute for IP and
    MPLS", draft-shen-nhop-fastreroute-01.txt, work in progress.

14. Author Information

   Albert Jining Tian
   Redback Networks, Inc.
   300 Holger Way
   San Jose, CA 95134
   Email: tian@redback.com

   George Apostolopoulos
   ICS-FORTH, Institue of Computer Science,
   Foundation of Research and Technology Hellas
   Email: georgeap@ics.forth.gr

Tian & Apostolopoulos                                          [Page 11]

Internet Draft   draft-tian-mpls-lsp-source-route-01.txt       July 2004

15. Full Copyright Statement

   Copyright (C) The Internet Society (year).  This document is subject
   to the rights, licenses and restrictions contained in BCP 78, and
   except as set forth therein, the authors retain all their rights.

   This document and the information contained herein are provided on an

Tian & Apostolopoulos                                          [Page 12]

Html markup produced by rfcmarkup 1.129c, available from https://tools.ietf.org/tools/rfcmarkup/